Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Modelling TiO2 photoanodes for PEC water splitting: Decoupling the influence of intrinsic material properties and film thickness

  • Ansón-Casaos, A.
  • Ciria, J.C.
  • Martínez Barón, C.
  • Villacampa, B.
  • Benito, A.M.
  • Maser, W.K.
Semiconductor metal oxides are intensively studied in electrodes for photoelectrochemical (PEC) water splitting. On a series of nanoparticulate TiO2 photoanodes, we analyze specific fabrication variables by means of data fitting. First, the experimental outcome is gathered using PEC characterization techniques, mostly cyclic voltammetry and transient photocurrent measurements. Subsequently, we apply models to gain insights into the involved charge trapping and transfer phenomena. We find that capacitance coefficients and the switch-on transient kinetics depend on the TiO2 layer thickness, respectively indicating surface mechanisms and stationary regimes that are mediated by light accessibility. On the contrary, exponential factors of capacitance are independent of thickness, but reflect changes in the density of electron states with different sintering atmospheres. Also, the transfer resistance in the electrolyte side is indirectly influenced by sintering. Through meticulous quantitative analysis of trends, we stablish simple mathematical relationships that connect thickness-dependent parameters. This knowledge delves into fundamental mechanisms governing the TiO2 photoelectrode behaviour, and aims to facilitate further improvements in the efficiency of materials and electrodes for green hydrogen production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Oil-in-Water Pickering Emulsions Stabilized with Nanostructured Biopolymers: A Venue for Templating Bacterial Cellulose

  • Calvo, Víctor
  • Fuentes, Laura
  • Berdejo, Daniel
  • González-Domínguez, José M.
  • Maser, Wolfgang K.
  • Benito, Ana M.
Pickering emulsions (PEs) differ from conventional emulsions in the use of solid colloidal particles as stabilizing agents instead of traditional amphiphilic molecules. Nanostructured biopolymers (NBs) emerge as a promising alternative for PE stabilization owing to their remarkable biocompatibility, abundant availability, and low cost. To explore this potential, a study is herein presented, in which cellulose nanocrystals (CNCs), both type I and type II allomorphs, and chitin nanocrystals (ChNCs) were used for stabilizing oil-in-water PEs prepared by the use of ultrasound. Sunflower oil was selected as the oil phase as it offers the advantages of being edible, renewable, and inexpensive. By utilizing ζ-potential, static light diffraction, and visual observations, we determined the optimal oil/water ratio for each type of NB to obtain stable emulsions after 14 days. The optimized PEs were used to form bacterial nanocellulose composites through emulsion templating. To our knowledge, this study represents a pioneering work in exploiting oil-in-water PEs for this approach. Additionally, it entails the first utilization of nonmercerized type II CNCs as stabilizers for PEs, while also establishing a direct comparison among the most relevant NBs. The resulting composites exhibited a unique morphology, composed of larger pores compared to standard bacterial nanocellulose aerogels. These findings highlight the notable potential of NBs as stabilizers for PEs and their ability to generate green nanocomposites with tailored properties.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Towards sustainable TiO2 photoelectrodes based on cellulose nanocrystals as a processing adjuvant

  • Martínez-Barón, C.
  • Calvo, V.
  • Hernández-Ferrer, J.
  • Villacampa, B.
  • Ansón-Casaos, A.
  • González-Domínguez, J. M.
  • Maser, W. K.
  • Benito, A. M.
Photoelectrodes of TiO2 in the form of films are commonly fabricated using screen printing techniques, employing viscous commercial TiO2 pastes. However, these pastes comprise environmentally unfriendly, multicomponent formulations designed to manufacture the photoactive TiO2 nanoparticles. To strive for sustainable processing and pave the way for the use of liquid-phase film processing technologies, the inherent limited water dispersibility of TiO2 nanoparticles must be overcome. In this study, we show that cellulose nanocrystals, produced via an environmentally benign one-pot hydrolysis process, enable the preparation of stable TiO2 water dispersions. The remarkable stability of these dispersions, evidenced by their outstanding ξ-potential values of −34 mV, facilitates the fabrication of macroporous TiO2 photoactive films throughout spray coating. Employed as photoanodes in a photoelectrochemical cell, our TiO2 photoanodes are compared with conventional TiO2 electrodes obtained from commercial pastes under water splitting conditions. Interestingly, our photoanodes reveal a remarkable three-fold enhancement of the photocurrent performance (132 vs. 46 μA cm−2) and a four-fold increase in the on–off response rate (4 vs. 1 s). These findings underscore the valuable role of cellulose nanocrystals as a green processing asset for achieving TiO2 water dispersions. Moreover, they serve as sacrificial adjuvants for preparing highly macroporous and functional film photoelectrodes, representing a significant step forward in the pursuit of sustainable and efficient materials processing.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Carbon nanomaterials-Based Inks and Electrodes Using Chitin Nanocrystals

  • Calvo, Víctor
  • Martínez-Barón, Carlos
  • Vázquez-Conejo, Benjamín
  • Domínguez-Alfaro, Antonio
  • Paleo, Antonio J.
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • González-Domínguez, José M.
Dispersing 1D carbon nanomaterials (CNMs) for film processing traditionally relies on surfactants or organic solvents. These methods, however, raise environmental concerns and can negatively impact the final properties of the CNMs. In this work we demonstrate that chitin nanocrystals (ChNCs) synthesized via acid hydrolysis provide a greener pathway for the development of waterborne CNMs-based inks, including single-walled carbon nanotubes, multiwalled carbon nanotubes, and carbon nanofibers. Various concentrations of ChNCs were mixed with each type of CNM to maximize the CNM concentration within the ink. In-depth characterization of the CNM/ChNC inks preceded their processing into supported conductive films by spray-coating. A subsequent thermal treatment of ChNCs at 450 °C leads to the efficient removal of ChNC and results in a significant enhancement of the electrical conductivity. Moreover, freeing the CNMs network structure contributes to increased electrochemical performance of the treated films, as expressed by improved Faradaic charge transfer efficiencies and kinetics reflected by 1 order of magnitude reduced rate constants, when tested with various redox probes. Our findings highlight the potential of ChNCs as a sustainable processing adjuvant of CNMs, leading to electrically conductive electrodes with suitable electrochemical properties for their use in diverse devices and applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Hybrids of Deep HOMO Organic Cyanoacrylic Acid Dyes and Graphene Nanomaterials for Water Splitting Photoanodes

  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Orduna, Jesús
  • Villacampa, Belén
  • Blesa, María-Jesús
Dye-sensitization is a promising strategy to improve the light absorption and photoactivity abilities of wide-bandgap semiconductors, like TiO2. For effective water-splitting photoanodes with no sacrificial agents, the electrochemical potential of the dye must exceed the thermodynamic threshold needed for the oxygen evolution reaction. This study investigates two promising organic cyanoacrylic dyes, designed to meet that criterion by means of theoretical calculations. Both yellow-colored dyes were synthesized and characterized by optical and photoelectrochemical techniques, demonstrating strong light absorption in the visible region, suitable experimental reduction potentials, and adsorption from the organic solvent onto mesoporous TiO2 layers. In addition, to promote immobilization in aqueous electrolytes, the dyes were hybridized with graphene oxide or multi-walled carbon nanotubes. Photoelectrochemical analysis of the dye-sensitized photoelectrodes demonstrated efficient charge transfer from the dyes to the TiO2 photoanode under simulated solar light. While the starting photocurrent notably surpassed the blank TiO2, a subsequent decay points to kinetic obstacles that still need to be overcome.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Fabrication of α-Fe<sub>2</sub>O<sub>3</sub> Nanoparticles/g-C<sub>3</sub>N<sub>4</sub> Direct Z-Scheme Heterojunction of Durable Photocatalytic Activity

  • Galán-González, Alejandro
  • Fernández, Isaías
  • Zaluzec, Nestor J.
  • Cambré, Sofie
  • Arenal, Raul
  • Benito, Ana M.
  • Maser, Wolfgang K.
The fabrication of a nanohybrid photocatalyst that combines α-Fe2O3 nanoparticles with graphitic carbon nitride (g-C3N4) is reported. The ensuing direct Z-scheme heterojunction greatly boosts the photocatalytic activity of the α-Fe2O3/g-C3N4 nanohybrids. This results in organic dye degradation rates more than two times higher than its individual components, promoted by the efficient charge separation and transfer of the Z-scheme heterojunction mechanism of the nanohybrid photocatalyst. In addition, recyclability tests show an outstanding stability of the nanohybrids spanning five consecutive dye degradation experiments, during which the degradation rate is slightly improved. The origin of the improved photocatalytic performance of the nanohybrid lies in the intimate interaction between α-Fe2O3 and g-C3N4 afforded by the two-step fabrication process, which enables the direct and controlled growth of α-Fe2O3 nanoparticles on g-C3N4. A first ultrasound impregnation step promotes the effective anchoring of stable Fe species via Fe−N and C−N/C−O bonding, while a second microwave phase conversion step induces the subsequent growth of α-Fe2O3 nanoparticles on the g-C3N4 sheets. Careful control of the FeCl3 precursor concentration up to a threshold value of 0.25 M during impregnation enables complete control over their size and phase. This approach clearly highlights the benefits of microwave reactor systems in the fabrication of hematite-based Z-scheme photocatalytic, overcoming the limitations of conventional thermal treatment technology.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Novel Methodology to Assess Salt Movement Between Mortar and Stones from Heritage in Spain

  • Pollet, Linde
  • Antolín-Rodríguez, Andrea
  • Gisbert-Aguilar, Josep
  • Búrdalo-Salcedo, Gabriel
  • Juan-Valdés, Andrés
  • García-Álvarez, César
  • Raga-Martín, Angel
  • Schroeyers, Wouter
  • Calvo, Víctor
  • Fernández-Raga, María
The development of sustainable cementitious materials is crucial to reduce the environmental footprint of the construction industry. Alkali-activated materials (AAMs) have emerged as promising environmentally friendly alternatives; however, their compatibility with natural stone in heritage structures remains poorly understood, especially regarding salt migration and related damage to stones. This study presents a novel methodology for assessing salt movement in solid materials between two types of stones—Boñar and Silos—and two types of binders: blended Portland cement (BPC) and an AAM. The samples underwent capillarity and immersion tests to evaluate water absorption, salt transport, and efflorescence behavior. The capillarity of the Silos stone was 0.148 kg·m−2·t−0.5, whereas this was 0.0166 kg·m−2·t−0.5 for the Boñar stone, a ninefold difference. Conductivity mapping and XRD analysis revealed that AAM-based mortars exhibit a significantly higher release of salts, primarily sodium sulfate, which may pose a risk to adjacent porous stones. In contrast, BPC showed lower salt mobility and different salt compositions. These findings highlight the importance of evaluating the compatibility between alternative binders and heritage stones. The use of AAMs may pose significant risks due to their tendency to release soluble salts. Although, in the current experiments, no pore damage or mechanical degradation was observed, additional studies are required to confirm this. A thorough understanding of salt transport mechanisms is therefore essential to ensure that sustainable restoration materials do not inadvertently accelerate the deterioration of structures, a process more problematic when the deterioration affects heritage monuments.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Novel Egg White Protein–Chitin Nanocrystal Biocomposite Films with Enhanced Functional Properties

  • Baquero-Aznar, Víctor
  • Calvo, Víctor
  • González-Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • Salvador, María Luisa
  • González-Buesa, Jaime
This study aims to develop egg white protein (EWP) biocomposite films reinforced with chitin nanocrystals (ChNCs, 1–5 wt.%) by compression molding to overcome the mechanical and barrier limitations of protein-based films for sustainable packaging. ChNC incorporation may modulate film microstructure, crystallinity, and thermal stability, thereby enhancing functional performance. Films were prepared by adding ChNCs either as aqueous suspensions or lyophilized powder, and their structural, thermal, mechanical, optical, and barrier properties were systematically evaluated. Scanning electron microscopy confirmed a more homogeneous dispersion of ChNCs when added as suspensions, while powder addition promoted partial aggregation. X-ray diffraction revealed increased crystallinity with ChNC reinforcement. Mechanical tests showed that films with 2 wt.% ChNCs in suspension exhibited the highest tensile strength, whereas those with 5 wt.% in powder form became stiffer but less extensible. Oxygen permeability was not significantly affected, while water vapor permeability decreased by up to 14.5% at 2 wt.% ChNCs incorporated as powder. Transparency and color remained largely unchanged by ChNC addition, except for a slight increase in yellowness. Overall, these findings demonstrate that the incorporation method and concentration of ChNCs play a crucial role in tailoring the physicochemical performance of EWP films. The results provide new insights into the design of EWP-based nanocomposites and support their potential as bio-derived materials for advanced food packaging applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

3-component (N, Fe, Co) atomically dispersed ORR catalysts prepared by laser-driven decomposition of organic precursors

  • Pakrieva, Ekaterina
  • Hernandez-Ferrer, Javier
  • Martinez, Gema
  • Balas, Francisco
  • García-Bordeje, Enrique
  • Anson-Casaos, Alejandro
  • Simonelli, Laura
  • Bartolome, Fernando
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Hueso, Jose L.
  • Santamaria, Jesus
The sluggish kinetics of the oxygen reduction reaction (ORR) remain a key bottleneck for the commercialization of proton exchange membrane fuel cells (PEMFCs), driving the search for efficient, non-precious metal catalysts. Herein, we present a laser-assisted pyrolysis strategy for the synthesis of nitrogen-doped carbon (NC) materials, both metal-free and containing atomically dispersed Fe and Co, using aerosolized phthalocyanine precursors and a near-instantaneous rapid decomposition under a high-energy laser beam, while preventing metal aggregation. A single-step post-synthetic thermal activation under an NH₃/N₂ atmosphere further tailors the textural and surface properties, without requiring ammonia co-feeding during laser pyrolysis, acid etching, or multiple treatments, marking a significant improvement over our previously reported single atom (Fe-N/C) protocols. The resulting Fe_Co/NC_tr catalyst exhibits high specific surface area, enhanced microporosity, improved graphitization, and increased abundance of electrochemically beneficial nitrogen sites. Compared to our earlier reported Fe–N/C catalysts, Fe_Co/NC_tr delivers significantly higher limiting current densities and enhanced durability in alkaline media. Overall, the developed Fe_Co/NC catalyst exhibits good ORR catalytic activity and outstanding long-term stability in alkaline media, comparable to the state-of-the-art commercial Pt/C catalysts. Cyanide poisoning tests confirm the essential role of atomically dispersed Fe2+ and Co2+ as active ORR sites.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The role of mild microwave irradiation in liquid-phase graphene oxide reduction toward aqueous dispersions and conductive films

  • Benito, A.M.
  • Galán-González, A.
  • Arenal, R.
  • Ansón-Casaos, A.
  • Maser, W.K.
The scalable and sustainable production of high-quality, solution-processable graphene materials remains a central challenge in nanomaterial research. This study investigates the reduction of graphene oxide (GO) in aqueous dispersions using low-power microwave (MW) irradiation and conventional thermal reflux, comparing four common chemical reductants, ascorbic acid, glucose, hydrazine, and sodium borohydride, alongside a reductant-free route. MW irradiation at 200 W induces rapid deoxygenation and enhancement of sp2-domain signatures within seconds, whereas reflux requires extended heating to achieve comparable effects. XPS and Raman analyses reveal that MW treatment promotes a more uniform reduction across reductants and leads to significantly larger apparent crystallite sizes (La) than reflux. Importantly, although chemical reductants remain active under MW conditions, their influence on structural reorganization and electrical performance is considerably diminished, demonstrating that MW field itself governs defect elimination and sp2-domain enrichment under these mild aqueous conditions. The reductant-free MW route yields the highest conductivity (88.4 S/m for 150 nm films) and the largest sp2-domains among all samples. Combined spectroscopic, electrical, and electronic microscopy evidence supports a mechanism in which MW irradiation selectively removes highly defective, oxygen-rich, and sp3-hybridized regions rather than reconstructing the graphene lattice, thereby enriching the remaining framework in extended sp2 networks. Overall, these results position mild MW irradiation as a rapid, and scalable strategy for producing structurally enhanced, water-dispersible rGO dispersions suitable for solution-processed graphene films.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Carbon nanotube film electrodes enabled by nanostructured biopolymers through aqueous processing

  • Martínez-Barón, Carlos
  • Calvo, Víctor
  • Álvarez-Sánchez, Miguel Ángel
  • Pascual, F. Javier
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • Ansón-Casaos, Alejandro
  • González-Domínguez, José Miguel
Processing carbon nanotubes (CNTs) into conductive films via liquid-phase is highly attractive for the fabrication of electronic and electrochemical device components. However, conventional deposition methods usually suffer from several limitations, including environmental concerns, loss of intrinsic properties, and poor reproducibility. Nanostructured biopolymers (NBs), such as cellulose (CNCs) and chitin (ChNCs) nanocrystals, offer an environmentally friendly strategy for dispersing CNTs in water alternative to organic solvents, surfactants or chemical functionalization. In this work, we present the first direct comparison of conductive and electroactive films resulting from using CNCs and ChNCs as dispersing agents for both single-walled and multi-walled CNTs. The as-made aqueous dispersions are used as inks to fabricate CNT/NB films via spray coating, achieving excellent homogeneity, controllable film thickness, and sheet resistances mostly below 130 Ohm Sq-1. Furthermore, we demonstrate that postdeposition thermal treatment at 450 1C in an inert atmosphere effectively pyrolyzes the non-conductive NB matrix while increasing contacts between CNTs in the network, leading to enhanced electrical conductivities and lectrochemically active surface areas. These findings highlight NBs as greener processing agents for the formulation of waterborne CNT inks and emphasize their relevance for the controlled and sustainable fabrication of conductive films and electrodes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Tuning 2e− and 4e− oxygen reduction pathways in laser-driven FeC electrocatalysts for H2O2 production and Zn–air batteries

  • Pakrieva, Ekaterina
  • Hernández-Ferrer, Javier
  • Rueda-Flores, Ana
  • Balas, Francisco
  • García-Bordeje, Enrique
  • Ansón-Casaos, Alejandro
  • Usoltsev, Oleg
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Hueso, Jose L.
Electrocatalytic oxygen reduction plays a central role in electrochemical energy technologies and in the production of hydrogen peroxide. Achieving selective control over the two-electron (2e−) and four-electron (4e−) oxygen reduction reaction (ORR) pathways within a single catalyst platform remains challenging. Here, we report a laser-driven synthesis of Fesingle bondC nanostructures that enables tunable ORR selectivity through controlled post-treatment. Air annealing at 300 °C yields high H2O2 selectivity (~75% at 0.65 V vs RHE), attributed to oxygen-rich groups and well-developed mesoporosity. Notably, with an optimized 2-electron catalyst, 80 ppm of H2O2 with 94% faradaic efficiency was achieved after 24 h of electrolysis. In contrast, an ammonia based (NH3/N2) treatment at 900 °C promotes the formation of a microporous structure and the incorporation of nitrogen species, resulting in selective water production (~86% at 0.65 V vs RHE). The 4-electron catalyst delivers power and stability comparable to Pt/GC in a primary zinc–air battery. These findings demonstrate a practical approach for tuning ORR selectivity within a Fe-containing carbon-based platform, using scalable processing and trace Fe contents (<0.1 wt%) with Fe present as atomically dispersed sites, limiting leaching and Fenton-type reactions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Quantitative correlation between cyclic voltammetry and electrochemical impedance spectroscopy models on TiO2 film electrodes

  • Ansón-Casaos, Alejandro
  • Ciria, José C.
  • Esteban-Tello, Pedro
  • Galán-González, Alejandro
  • Hernández-Ferrer, Javier
  • Maser, Wolfgang K.
  • Benito, Ana M.
Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) are widely used to characterize semiconductor electrodes, yet their quantitative equivalence is not often established. Here, we introduce a model framework that clarifies when CV and EIS probe the same physical processes and when they diverge on TiO2 film photoelectrodes with controlled thickness and morphology. EIS measurements are registered at different potentials, covering the whole CV window, and show a progressive evolution. In the general case, outside the charge-accumulation regime, the low-frequency limit of EIS converges quantitatively with a density-of-states-based CV description, demonstrating that both techniques capture identical electronic responses. At more cathodic potentials, systematic deviations arise: EIS yields larger capacitances and lower Faradaic resistances than CV. These discrepancies possibly originate from the different timescales of the techniques, as the longer polarization of EIS may activate slow electrochemical processes that are kinetically inaccessible during CV. The divergence between CV and EIS therefore suggests an onset for different charge transport regimes. In this way, the proposed framework provides a predictive diagnostic tool for TiO2 film electrodes, supporting a consistent interpretation and cross-validation of classical CV and EIS data.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Bottom-up assembly of cellulose nanocrystals as a green entry to structured functional carbons

  • Güemes, Lucas
  • Calvo, Víctor
  • Maya-Segura, Vanessa B.
  • Pires, Elísabet
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • García-Bordejé, Enrique
  • González-Domínguez, José M.
The bottom-up assembly of cellulose nanocrystals (CNCs) into porous scaffolds offers a sustainable route to translate their intrinsic properties into functional 3D materials. This strategy enables precise control over porous architectures, unlocking opportunities for high-performance materials tailored to specific applications. Here, we present the fabrication of structured carbons derived from nanocellulose precursors. CNCs are isolated from cellulosic feedstock in type-I and type-II crystalline allomorphs via a one-pot synthesis process followed by minimal processing steps. The resulting aqueous CNC colloids self-assemble into cross-linked hydrogels through controlled hydrothermal aggregation, followed by lyophilization to produce macroporous aerogels (bulk porosities up to 98%). Each allomorph exhibits distinct aggregation behavior, explored for the first time with type-II CNCs. As proof of concept, these aerogels undergo pyrolysis at varying temperatures and subsequent sulfonation, yielding highly porous carbons functionalized with sulfonic acid groups (functionalization degree of ca. 2400 μmol·g−1). The resulting materials combine macroporosity from hydrothermal assembly with microporosity generated during pyrolysis and sulfonation, forming a hierarchical structure ideal for catalytic applications. Their performance is demonstrated in solketal synthesis (yielding ∼90% of solketal in consecutive cycles after 4 h at room temperature) positioning CNC-based sulfonated aerogels as a greener alternative to conventional Brønsted acid catalysts and surpassing classical activated carbons in sustainability and design.