Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Production of antioxidants for biodiesel from straw black liquor depolymerization

  • Palomo de la Fuente, José Fernando
  • Molés Algarra, Samuel
  • Salafranca Lázaro, Jesús
  • Gil Lalaguna, Noemí
  • Gonzalo Callejo, Alberto
  • Sánchez Cebrián, José Luis
Black liquor produced from semichemical pulping of barley straw has been depolymerized at different temperatures (250 to 325 ºC), time (1 to 3 h) and initial solids content in the black liquor (7 to 14 %). The obtained degraded and soluble lignin was then used as biodiesel stabilizer (against oxidation). The depolymerization products have been analyzed by gel permeation chromatography, gas chromatography-mass spectrometry (GC-MS), Fourier-transform infrared spectroscopy (FTIR) and phenolic content was quantified by using the Folin-Ciocalteu method. Regarding the molecular weight distribution, temperature and time have been the most influential factors, especially temperature that decreased the observed molecular weight. The presence of volatile phenolic compounds has been determined by GC-MS. Temperature was found to be the most influential factor: the higher the temperature the lower concentration of volatile phenolics. Regarding the FTIR, the measured spectra hardly change when modifying the experimental conditions. Oxidation stability of biodiesel increased with the reaction temperature applied to black liquor, suggesting that the increase of oxidation stability is not only caused by the volatile phenolic compounds.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Adsorption performance of physically activated biochars for postcombustion Co2 capture from dry and humid flue gas

  • Manyà, Joan J.
  • García-Morcate, David
  • González, Belén
In the present study, the performance of four biomass-derived physically activated biochars for dynamic CO2 capture was assessed. Biochars were first produced from vine shoots and wheat straw pellets through slow pyrolysis (at pressures of 0.1 and 0.5 MPa) and then activated with CO2 (at 0.1 MPa and 800 C) up to different degrees of burn-off. Cyclic adsorption-desorption measurements were conducted under both dry and humid conditions using a packed-bed of adsorbent at relatively short residence times of the gas phase (12-13 s). The adsorbent prepared from the vine shoots-derived biochar obtained by atmospheric pyrolysis, which showed the most hierarchical pore size distribution, exhibited a good and stable performance under dry conditions and at an adsorption temperature of 50 C, due to the enhanced CO2 adsorption and desorption rates. However, the presence of relatively high concentrations of water vapor in the feeding gas clearly interfered with the CO2 adsorption mechanism, leading to significantly shorter breakthrough times. In this case, the highest percentages of a used bed were achieved by one of the other activated biochars tested, which was prepared from the wheat straw-derived biochar obtained by pressurized pyrolysis.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Study of the conversion of CH4/H2S mixtures at different pressures

  • Colom-Díaz, J. M.
  • Leciñena, M.
  • Peláez, A.
  • Abián, M.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
Due to the different scenarios where sour gas is present, its composition can be different and, therefore, it can be exploited through different processes, being combustion one of them. In this context, this work deals with the oxidation of CH4 and H2S at different pressures and under a wide variety of conditions. The oxidation has been evaluated experimentally in two different flow reactor set-ups, one working at atmospheric pressure and another one operating from atmospheric to high pressures (40 bar). Different CH4/H2S mixtures have been tested, together with different oxygen concentrations and in the temperature range of 500–1400 K. The experimental results obtained show that the oxidation of the CH4/H2S mixtures is shifted to lower temperatures as pressure increases, obtaining the same trends at atmospheric pressure in both experimental set-ups. H2S oxidation occurs prior to CH4 oxidation at all conditions, providing radicals to the system that promote CH4 oxidation to lower temperatures (compared to neat CH4 oxidation). This effect is more relevant as pressure increases. H2S oxidation is inhibited by CH4 at atmospheric pressure, being more noticeable when the CH4/H2S ratio is higher. At higher pressures, the H2S conversion occurs similarly in the absence or presence of CH4. The experimental results have been modeled with an updated kinetic model from previous works from the literature, which, in general, matches well the experimental trends, while some discrepancies between experimental and modeling results at atmospheric pressure and 40 bar are found in the conversion of H2S and CH4.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Joint quantification of PAH and oxy-PAH from standard reference materials (urban dust and diesel particulate matter) and diesel soot surrogate by GC-MS

  • Viteri, Fausto
  • Pezo Piña, Davinson
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María Uxue
The combustion of fossil fuels produces pollutants such as soot, which consists of carbonaceous particles whose emission is regulated by environmental laws. Soot is mainly formed from polycyclic aromatic hydrocarbons (PAH), through different reaction ways and, once formed, it can adsorb PAH on its surface. These compounds have an environmental importance due to their carcinogenic and mutagenic potential. In the last years, the oxygenated derivatives of PAH (oxy-PAH) have also been considered as dangerous since they have been found to be mutagenic for bacterial and human cells. Therefore, the purpose of this work was to quantify simultaneously selected PAH and oxy-PAH from different samples of soot. The quantification method involves Soxhlet extraction and subsequent concentration by rotary evaporation that allows to recover the analysed compounds from soot samples. The PAH and oxy-PAH were identified and quantified, by a single injection, using a gas chromatograph-mass spectrometer (GC-MS). The method showed a good repeatability using a diesel soot surrogate test sample, Printex-U. The validation process showed that most of the compounds are recovered between the values established for the Standard Reference Materials analysed, 1650b and 1649b. The values of the mass fraction of the oxy-PAH obtained in this work showed, in general, a good match with those indicated in other studies.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Physically activated wheat straw-derived biochar for biomass pyrolysis vapors upgrading with high resistance against coke deactivation

  • Di Stasi, Christian
  • Alvira, Darío
  • Greco, Gianluca
  • González, Belén
  • Manya, Joan J.
Wheat straw-derived biochars (produced through slow pyrolysis at 500 degrees C and 0.1 MPa) were physically (with CO2) and chemically (with K2CO3) activated to assess their performance as renewable and low-cost catalysts for biomass pyrolysis vapors upgrading. Preliminary cracking experiments, which were carried out at 700 degrees C using a mixture of four representative model compounds, revealed a clear correlation between the volume of micropores of the catalyst and the total gas production, suggesting that physical activation up to a degree of burn-off of 40% was the most interesting activation route. Next, steam reforming experiments were conducted using the most microporous material to analyze the effect of both the bed temperature and gas hourly space velocity (GHSV) on the total gas production. The results showed a strong dependence between the bed temperature and the total gas production, with the best result obtained at the highest temperature (750 degrees C). On the other hand, the change in GHSV led to minor changes in the total gas yield, with a maximum achieved at 14500 h(-1). Under the best operating conditions deduced in the previous stages, the addition of CO2 into the feed gas stream (partial pressure of 20 kPa) resulted in a total gas production of 98% with a H-2/CO molar ratio of 2.16. This good result, which was also observed during the upgrading of the aqueous phase of a real biomass pyrolysis oil, was ascribed to the relatively high coke gasification rate, which refresh the active surface area preventing deactivation by coke deposition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Glycerol conversion to valuable products by pressure aqueous processing using ni-al-fe catalysts

  • Raso, R.
  • Ruíz, J.
  • Oliva, M.
  • García, L.
  • Arauzo, J.
The present work studied the pressure aqueous processing of glycerol (by-product of biodiesel) without external hydrogen addition to produce value-added products. A series of Ni catalysts supported on Al2O3 and Fe as promoter were prepared through co-precipitation technique by changing the Fe/Al ratio (0, 25 and 75% molar). The prepared samples were characterized by several techniques (XRD, H2-TPR, N2 adsorption and ICP-OES). All the catalysts showed a low carbon conversion to gas and high carbon conversion to liquid products mainly 1, 2-propanediol, acetol and ethylene glycol. This work demonstrates the effects of the molar ratio of Fe/Al on physicochemical characteristics of Ni-Al-Fe catalysts and during the pressure aqueous processing (PAP) of glycerol to value-added products. El presente trabajo estudió el procesamiento acuoso a presión de glicerol (subproducto del biodiesel) sin adición externa de hidrógeno para producir productos de valor agregado. Se prepararon una serie de catalizadores de Ni soportados sobre Al2O3 y Fe como promotor mediante la técnica de coprecipitación cambiando la relación Fe/Al (0, 25 y 75% molar). Las muestras preparadas se caracterizaron mediante varias técnicas (DRX, H2-TPR, adsorción de N2 e ICP-OES). Todos los catalizadores mostraron una baja conversión de carbono a gas y una alta conversión de carbono a productos líquidos, principalmente 1,2-propanodiol, acetol y etilenglicol. Este trabajo demuestra los efectos de la relación molar de Fe/Al sobre las características fisicoquímicas de los catalizadores de Ni-Al-Fe y durante el procesamiento acuoso a presión (PAP) de glicerol para obtener productos de valor agregado.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Hydrogenolysis of glycerol with external h2 supply as value-added liquid chemicals source

  • Jarauta-Córdoba, C.
  • Ehrmaier, A.
  • Denk, C.
  • Lercher, J.A.
  • García, L.
  • Ruíz, J.
  • Arauzo, J.
The hydrogenolysis process of glycerol with external H2 supply has been studied using Ni-exchanged zeolites (FAU, LTA, ZSM-5). The reaction temperature and the oxidation state of the active phase were investigated in this work. Ni/zeolite catalysts were tested for 3 hours in a batch reactor, at different temperatures between 200 and 250 ºC and at 33 bar of initial H2 pressure. A water solution of 5 wt.% glycerol was used as a feedstock. The liquid products collected were analyzed afterwards by GC-MS and GC-FID. Several catalyst characterization techniques were performed: N2 physisorption, XRD, AAS, NH3-TPD and FTIR of adsorbed probe molecule (pyridine or NH3). The relevance of the metallic function for the hydrogenation reaction was proved. In most cases, the increase of the reaction temperature between 200 and 250 ºC implies a steady increase in the glycerol conversion and in the carbon conversion to liquid products, both for the reduced and non-reduced catalysts. The temperature also influences the selectivity to liquid products. Moreover, some temperatures were proposed as optimal for the production of certain liquids under these conditions. El proceso de hidrogenólisis del glicerol con suministro externo de H2 se ha estudiado utilizando zeolitas intercambiadas con Ni (FAU, LTA, ZSM-5). En este trabajo se investigaron la temperatura de reacción y el estado de oxidación de la fase activa. Los catalizadores de Ni/zeolita se probaron durante 3 horas en un reactor discontinuo, a diferentes temperaturas entre 200 y 250 ºC y a 33 bar de presión inicial de H2. Se utilizó como materia prima una solución acuosa de 5% en peso de glicerol. Los productos líquidos recogidos se analizaron posteriormente mediante GC-MS y GC-FID. Se realizaron varias técnicas de caracterización de catalizadores: fisisorción de N2, XRD, AAS, NH3-TPD y FTIR de la molécula sonda adsorbida (piridina o NH3). Se demostró la relevancia de la función metálica para la reacción de hidrogenación. En la mayoría de los casos, el aumento de la temperatura de reacción entre 200 y 250 ºC implica un aumento constante en la conversión de glicerol y en la conversión de carbono a productos líquidos, tanto para los catalizadores reducidos como para los no reducidos. La temperatura también influye en la selectividad hacia los productos líquidos. Además, se propusieron algunas temperaturas como óptimas para la producción de determinados líquidos en estas condiciones.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Exploratory study of polycyclic aromatic hydrocarbons occurrence and distribution in manure pyrolysis products

  • Adánez-Rubio, I.
  • Fonts, I.
  • Blas, P. de
  • Viteri, F.
  • Gea, G.
  • Alzueta, M.U.
The occurrence and distribution of polycyclic aromatic hydrocarbons (PAH) have been investigated in the products derived from the pyrolysis of pig manure at low temperatures (<550 °C) in a fixed bed reactor. The focus was on the sixteen PAH identified as priority pollutants by the US Environment Protection Agency (EPA). The pyrolysis does not generate a significant additional amount of EPA-PAH to that existing in the original pig manure, under the operational conditions studied (<550 °C). While the total EPA-PAH yield does not indicate a notable dependence on the pyrolysis temperature, the EPA-PAH distribution among the three pig manure pyrolysis products as well as the speciation changed significantly with the temperature. The proportion of heavy PAH species increased as the temperature increased. The initial EPA-PAH in the manure samples plays a significant role in both their concentration and speciation in the biochar. The relationship of the EPA-PAH concentration and speciation in the biochar with those of the raw material was corroborated with a cow manure sample and the biochars obtained from its pyrolysis. For this reason, feedstocks with low EPA-PAH concentrations are recommended in order to obtain biochars with concentrations below the maximum allowed threshold established for their use as a soil enhancer by the International Biochar Initiative (IBI) and in the European Biochar Certificate.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Functionalization of sewage sludge char by partial oxidation with molecular oxygen to enhance its adsorptive properties

  • Atienza-Martínez, M.
  • Binti Suraini, N.N.
  • Ábrego, J.
  • Fonts, I.
  • Lázaro, L.
  • Carstensen, H.H.
  • Gea, G.
This study investigates the activation of sewage sludge char through partial oxidation with molecular oxygen with the goal to increase the concentration of oxygen-containing surface functional groups and to enhance its ammonium adsorption capacity. The effects of oxidation temperature (200–350 °C), oxygen concentration (5–21 vol %) and oxidation time (30–120 min) on the degree of char oxidation are analyzed. The results obtained by thermogravimetric and elemental analysis, and Fourier Transform Infrared and X-ray Photoelectron spectroscopy corroborate the incorporation of oxygenated functional groups on the surface of sewage sludge char either at low temperature (200 °C) using air or at higher temperature (350 °C) using 5% O2 for 30 min. The oxidation of sewage sludge char hardly increases its specific surface area. The operating conditions during oxidation must be carefully controlled to avoid runaway reactions that lead to total oxidation of char. The evolution of CO and CO2 during oxidation is a good indicator of the advance of the oxidation/burn-off reactions. The ammonium adsorption capacity of sewage sludge char increases after oxidation under mild operating conditions, providing support to the idea of onsite utilization of sewage sludge as ammonium adsorbent in waste water treatment plants. This would provide a step forward towards the implementation of a circular economy.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Activated olive mill waste-based hydrochars as selective adsorbents for CO2 capture under postcombustion conditions

  • González, B.
  • Manyà, J. J.
Porous carbons are considered to be promising sorbents for carbon capture and sequestration. As precursors, the use of biomass materials has acquiring special interest due to its low cost and high availability. Among all the possibilities to convert low-value biomass into these interesting sorbents, hydrothermal carbonization has demonstrated several advantages such as lower energy consumption over pyrolysis. In this work, activated hydrochars using two-phase olive mill waste as precursor have been prepared through physical and chemical activation using CO2 and KOH, respectively. Additionally, with the aim to study the influence of the nitrogen on their adsorption capacity, N-doped adsorbents have been prepared through a one-step hydrothermal carbonization. The behaviour of these adsorbents has been studied in terms of CO2 uptake capacity at an absolute pressure of 15 kPa and temperatures of 0, 25 and 75 °C, apparent selectivity towards CO2 over N2, and isosteric heat of adsorption. Among all these samples, the physically activated hydrochar appears to be the best due to its higher CO2 uptakes, adsorption rates and values of selectivity at 25 °C. Therefore, considering these results, doping these materials with nitrogen does not appear to enhance their adsorption properties, contrary to what some authors have previously reported. © 2020 Elsevier B.V.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental Study of the Pyrolysis of NH3under Flow Reactor Conditions

  • Benés, M.
  • Pozo, G.
  • Abián, M.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
The possibility of using ammonia (NH3), as a fuel and as an energy carrier with low pollutant emissions, can contribute to the transition to a low-carbon economy. To use ammonia as fuel, knowledge about the NH3 conversion is desired. In particular, the conversion of ammonia under pyrolysis conditions could be determinant in the description of its combustion mechanism. In this work, pyrolysis experiments of ammonia have been performed in both a quartz tubular flow reactor (900-1500 K) and a non-porous alumina tubular flow reactor (900-1800 K) using Ar or N2 as bath gas. An experimental study of the influence of the reactor material (quartz or alumina), the bulk gas (N2 or Ar), the ammonia inlet concentration (1000 and 10a 000 ppm), and the gas residence time [2060/T (K)-8239/T (K) s] on the pyrolysis process has been performed. After the reaction, the resulting compounds (NH3, H2, and N2) are analyzed in a gas chromatograph/thermal conductivity detector chromatograph and an infrared continuous analyzer. Results show that H2 and N2 are the main products of the thermal decomposition of ammonia. Under the conditions of the present work, differences between working in a quartz or non-porous alumina reactor are not significant under pyrolysis conditions for temperatures lower than 1400 K. Neither the bath gas nor the ammonia inlet concentration influence the ammonia conversion values. For a given temperature and under all conditions studied, conversion of ammonia increases with an increasing gas residence time, which results into a narrower temperature window for NH3 conversion.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

CO2 adsorption on pyrolysis char from protein-containing livestock waste: How do proteins affect?

  • Gil-Lalaguna, Noemí
  • Navarro-Gil, África
  • Carstensen, Hans-Heinrich
  • Ruiz, Joaquín
  • Fonts, Isabel
  • Ceamanos, Jesús
  • Murillo, María Benita
  • Gea, Gloria
Biogas generation through anaerobic digestion provides an interesting opportunity to valorize some types of animal waste materials whose management is increasingly complicated by legal and environmental restrictions. To successfully expand anaerobic digestion in livestock areas, operational issues such as digestate management must be addressed in an economical and environmentally sustainable way. Biogas upgrading is another necessary stage before intending it to add-value applications. The high concentration of CO2 in biogas results in a reduced caloric value, so the removal of CO2 would be beneficial for most end-users. The current work evaluates the CO2 uptake properties (thermogravimetry study) of low-cost adsorbent materials produced from the animal wastes generated in the livestock area itself, specifically via pyrolysis of poorly biodegradable materials, such as meat and bone meal, and the digestate from manure anaerobic digestion. Therefore, the new element in this study with respect to other studies found in the literature related to biochar-based CO2 adsorption performance is the presence of high content of pyrolyzed proteins in the adsorbent material. In this work, pyrolyzed chars from both meat and bone meal and co-digested manure have been proven to adsorb CO2 reversibly, and also the chars produced from their representative pure proteins (collagen and soybean protein), which were evaluated as model compounds for a better understanding of the individual performance of proteins. The ultra-microporosity developed in the protein chars during pyrolysis seems to be the main explanation for such CO2 uptake capacities, while neither the BET surface area nor N-functionalities on the char surface can properly explain the observed results. Although the CO2 adsorption capacities of these pristine chars (6–41.0 mg CO2/g char) are far away from data of commercially activated carbons (~80 mg CO2/g char), this application opens a new via to integrate and valorize these wastes in the circular economy of the primary sector.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High pressure ammonia oxidation in a flow reactor

  • García-Ruiz, P.
  • Uruén, M.
  • Abián, M.
  • Alzueta, M.U.
The present work deals with an experimental and modeling analysis of ammonia oxidation at high pressure (up to 40 bar), in the 600–1275 K temperature range using a quartz tubular reactor and argon as diluent. The impact of temperature, pressure, oxygen stoichiometry and presence of NO has been analyzed on the concentrations of NH3 and N2 obtained as main products of ammonia oxidation. The main results obtained indicate that increasing either pressure or stoichiometry results in a shift of NH3 conversion to lower temperatures. The effect of pressure is particularly significant in the low range of pressures studied. The main product of ammonia oxidation is N2, while NO, NO2 and N2O concentrations are below the detection limit for all the conditions considered. The experimental results are simulated and interpreted in terms of a literature detailed chemical kinetic mechanism, which, in general, predicts satisfactorily the experimental results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Assessing the Importance of Pyrolysis Process Conditions and Feedstock Type on the Combustion Performance of Agricultural-Residue-Derived Chars

  • Manyà, J.J.
  • Alvira, D.
  • Videgain, M.
  • Duman, G.
  • Yanik, J.
The combustion performance of chars derived from vine shoots, wheat straw, and corn stover was investigated to assess the influence of both the biomass precursor and pyrolysis operating conditions. Chars were produced through slow pyrolysis at different peak temperatures (350 and 500 °C), pressures (0.1 and 0.5 MPa), and residence times of the vapor phase (50 and 150 s). From the thermogravimetric curves obtained under air, the combustion performance index (S) was calculated for each char. Apparent kinetics were also estimated using the Coats–Redfern method and assuming an F3/2 reaction model. Results show that the combustion patterns of chars were more influenced by the type of feedstock than by the pyrolysis conditions. Corn stover appeared to be the most interesting feedstock in order to produce chars with tuned reactivity. Results from partial least-squares (PLS) regression revealed that the most important factors affecting S were the contents of potassium (negative effect) and cellulose (positive effect) in the original biomass.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pyrolysis of dairy cattle manure: evolution of char characteristics

  • Atienza-Martínez, María
  • Ábrego, Javier
  • Gea, Gloria
  • Marías, Frédéric
Livestock manure management constitutes a major challenge at this time. Traditionally, this waste has been used as fertilizer. Excessive application of this residual organic matter on agricultural soils can cause soil quality degradation due to heavy metals accumulation, migration of pathogens to water sources and food, and generation of greenhouse gases. As a promising alternative to land application, pyrolysis of livestock manure allows to obtain biochar, bio-oil and syngas. The goal of this work is to study slow pyrolysis of digested dairy cattle manure (DM) both through one-step and multi-step pyrolysis at increasing temperature in the range 250-600 °C. The non-condensable gases composition was continuously analyzed by gas chromatography. Char properties were characterized by ultimate analysis, heavy metals content, ash content, higher heating value (HHV), pH, electrical conductivity (EC), water holding capacity (WHC), cation exchange capacity (CEC), textural properties (specific surface area, pore volume and average pore width) and Fourier Transform Infrared (FTIR) spectroscopy. The experimental results showed that both the product distribution and the properties of char depended on pyrolysis temperature. Char obtained after the last step of multi-step pyrolysis had similar properties to that obtained in one-step pyrolysis. Thus, the cooling and re-heating of the solid between steps did not have a significant effect on the pyrolysis pathway. Pyrolysis at between 400-550 °C allowed to reach a compromise between char pH and electrical conductivity for its potential use as soil amendment.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Reactivity and Physicochemical Properties of the Soot Produced in the Pyrolysis of 2, 5-Dimethylfuran and 2-Methylfuran

  • Alexandrino, Katiuska
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
Alkylated furan derivatives, such as 2, 5-dimethylfuran (2, 5-DMF) and 2-methylfuran (2-MF), have shown, at laboratory scale, a relatively high tendency to form soot. However, soot emissions from diesel engines are lower when diesel/2, 5-DMF and diesel/2-MF blends are used. This could indicate that the soot produced in the conversion of these compounds has high reactivity toward some gases present within the combustion chamber, reducing soot emissions in the exhaust gas. In this context, a study on the reactivity and the characterization of the soot generated in the pyrolysis of 2, 5-DMF and 2-MF, under different experimental conditions, was performed in an effort to increase the understanding of the reactivity and physicochemical properties of the soot originating in the conversion of these furan derivatives. The soot samples analyzed were obtained in previous works using different concentrations of the alkylated furan derivatives (5000, 7500, and 15â»000 ppm of 2, 5-DMF, and 9000 and 18â»000 ppm of 2-MF) and at different temperatures (1275, 1375, and 1475 K). The reactivity experiments were performed at 1275 K with 500 ppm of O2 and 2000 ppm of NO in a tubular quartz flow reactor. Different instrumental analysis techniques were employed to characterize the soot samples and to try to link the soot reactivity with its physicochemical properties. The dependence of soot reactivity and properties with soot formation conditions, namely, temperature and inlet fuel concentration, is studied.