Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Escaping undesired gas-phase chemistry: Microwave-driven selectivity enhancement in heterogeneous catalytic reactors

  • Ramírez, Adrian
  • Hueso, José L.
  • Abian, Olga
  • Alzueta, M.U.
  • Mallada, Reyes
  • Santamaría, Jesús
Research in solid-gas heterogeneous catalytic processes is typically aimed toward optimization of catalyst composition to achieve a higher conversion and, especially, a higher selectivity. However, even with the most selective catalysts, an upper limit is found: Above a certain temperature, gas-phase reactions become important and their effects cannot be neglected. Here, we apply a microwave field to a catalyst-support ensemble capable of direct microwave heating (MWH). We have taken extra precautions to ensure that (i) the solid phase is free from significant hot spots and (ii) an accurate estimation of both solid and gas temperatures is obtained. MWH allows operating with a catalyst that is significantly hotter than the surrounding gas, achieving a high conversion on the catalyst while reducing undesired homogeneous reactions. We demonstrate the concept with the CO 2 -mediated oxidative dehydrogenation of isobutane, but it can be applied to any system with significant undesired homogeneous contributions., Financial support from the European Research Council Advanced Grant (HECTOR267626), the Regional Government of Aragon (DGA), and the MINECO and FEDER (project CTQ2015-65226) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A study of dimethyl carbonate conversion and its impact to minimize soot and NO emissions

  • Alzueta, M. U.
  • Salinas, Pablo
  • Millera, Ángela
  • Bilbao, Rafael
  • Abián, María
6 figures, 3 tables.-- Supplementary material under CC-BY license https://creativecommons.org/licenses/by/4.0/, Fuel reformulation through the use of oxygenated compounds e.g. dimethyl carbonate (DMC) is a potential option both to reduce the harmful soot emissions and to overcome the dependence on fossil fuels since many of them are bio-derived fuels. DMC presents a relative high oxygen content as compared with other additives and suitable characteristics to be used in combustion systems. The different fundamental aspects of the DMC combustion process including its oxidation behavior its tendency to produce soot and the role of the NO presence in the reaction system were studied. Experiments were conducted under well controlled conditions using specifically designed flow reactor systems. Results demonstrated the low tendency of DMC to form soot compared to other oxygenates and its capacity to contribute to NO reduction under specific fuel-rich conditions. Modeling calculations successfully reproduce reasonably well the experimental trends observed and emphasized the sensitivity of the results to the thermodynamic data of DMC and DMC derived species., Authors acknowledge the Aragón Government and the European Social Fund, GPT group, and MINECO and FEDER (Project CTQ2015-65226-R) for financial support. Dr. M. Abián acknowledges the MINECO and Instituto de Carboquímica (ICB-CSIC) for the post-doctoral grant awarded (FPDI-2013-16172).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of dimethyl ether addition on the oxidation of acetylene in the absence and presence of NO

  • Marrodán, Lorena
  • Berdusán, Laura
  • Aranda, Verónica
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
Dimethyl ether (DME) is a promising diesel fuel additive for reducing soot and NOx emissions, because of its interesting properties and the possibility of a renewable production. An experimental and modeling study of the oxidation of acetylene (C2H2, considered as an important soot precursor) and DME mixtures has been performed under well-controlled flow reactor conditions. The influence of temperature, air excess ratio (¿) and presence of NO on the oxidation process has been analyzed. Under fuel-rich conditions, the presence of DME in these mixtures modifies the radical pool delaying the acetylene consumption. C2H2 and DME, and the radicals generated in their conversion, interact with NO achieving different levels of NO concentration diminution depending upon the operating conditions. Under fuel-lean conditions, the presence of DME in the mixtures increases the NO diminution, whereas for the other values of ¿ considered, the maximum NO decrease reached is lower than that obtained in the case of pure acetylene.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Sooting propensity of dimethyl carbonate, soot reactivity and characterization

  • Alexandrino, K.
  • Salinas, J.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
Oxygenated compounds have gained interest in the last few years because they represent an attractive alternative as additive to diesel fuel for reducing soot emissions. Although dimethyl carbonate (DMC) seems to be a good option, studies about its propensity to form soot, as well as the knowledge of the characteristics of this soot are still missing. For that reason, this paper focuses on the potential of DMC to form soot, as well as on the reactivity and characterization of this soot. Results from pyrolysis experiments performed in an atmospheric pressure flow reactor at different temperatures (1075-1475 K) and inlet DMC concentrations (approximately 33, 333 and 50, 000 ppm) show that both soot and gas yields are affected by the pyrolysis temperature, while an increase in the inlet DMC concentration only affects slightly the soot yield, without notable influence on the gas yield. DMC shows a very low tendency to produce soot because the CO/CO2 formation is favoured and thus few carbon atoms are available for soot formation. A chemical kinetic model developed, without incorporating soot particles dynamics, can predict well the gas-phase trends. The comparison of the soot amount profile obtained with the PAH amount profile determined by the model suggests a good first approach toward a model including soot formation. The soot reactivity study toward O2 (500 ppm) and NO (2000 ppm) at 1475 K, as well as its characterization, show that the higher the temperature and the inlet DMC concentration of soot formation, the lower the reactivity of the soot.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Importance of Vanadium-Catalyzed Oxidation of SO2 to SO3 in Two-Stroke Marine Diesel Engines

  • Colom, J.M.
  • Alzueta, M.U.
  • Christensen, J.M.
  • Glarborg, P.
  • Cordtz, R.
  • Schramm, J.
Low-speed marine diesel engines are mostly operated on heavy fuel oils, which have a high content of sulfur and ash, including trace amounts of vanadium, nickel, and aluminum. In particular, vanadium oxides could catalyze in-cylinder oxidation of SO2 to SO3, promoting the formation of sulfuric acid and enhancing problems of corrosion. In the present work, the kinetics of the catalyzed oxidation was studied in a fixed-bed reactor at atmospheric pressure. Vanadium oxide nanoparticles were synthesized by spray flame pyrolysis, i.e., by a mechanism similar to the mechanism leading to the formation of the catalytic species within the engine. Experiments with different particle compositions (vanadium/sodium ratio) and temperatures (300–800 °C) show that both the temperature and sodium content have a major impact on the oxidation rate. Kinetic parameters for the catalyzed reaction are determined, and the proposed kinetic model fits well with the experimental data. The impact of the catalytic reaction is studied with a phenomenological zero-dimensional (0D) engine model, where fuel oxidation and SOx formation is modeled with a comprehensive gas-phase reaction mechanism. Results indicate that the oxidation of SO2 to SO3 in the cylinder is dominated by gas-phase reactions and that the vanadium-catalyzed reaction is at most a very minor pathway.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of the presence of hydrogen sulphide on the formation of light gases, soot and PAH during the pyrolysis of ethylene

  • Viteri Moya, Fausto
  • Sánchez, Adrián
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
The formation of light gases, soot, and 16 polycyclic aromatic hydrocarbons (EPA-PAH), classified as priority pollutants by the United States Environmental Protection Agency (USEPA), has been studied during the pyrolysis of mixtures of ethylene with hydrogen sulfide (H2S) in a tubular flow reactor setup. The study was made using a constant concentration of ethylene and different inlet concentrations of H2S, in a temperature range from 1075 to 1475 K. The light gases produced were quantified by a chromatographic method. The soot amount formed was also quantified at the outlet of the reactor. The speciation of the individual EPA-PAH compounds was made by a combination of Soxhlet extraction, extract concentration by a rotary evaporator, and gas chromatography coupled to mass spectrometry. The present study shows that, under pyrolysis conditions, there is an effective interaction between H2S and hydrocarbons, forming significant amounts of CS2 and bonding sulfur to soot. The presence of H2S in the pyrolysis of ethylene contributes to slightly decrease the formation of soot and EPA- PAH, which indicates a positive effect of the sulfur compound under pyrolysis conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

A study of dimethyl carbonate conversion and its impact to minimize soot and NO emissions

  • Alzueta, María U.
  • Salinas, Pablo
  • Millera, Ángela
  • Bilbao, Rafael.
  • Abián, María
Fuel reformulation through the use of oxygenated compounds e.g. dimethyl carbonate (DMC) is a potential option both to reduce the harmful soot emissions and to overcome the dependence on fossil fuels since many of them are bio-derived fuels. DMC presents a relative high oxygen content as compared with other additives and suitable characteristics to be used in combustion systems. The different fundamental aspects of the DMC combustion process including its oxidation behavior its tendency to produce soot and the role of the NO presence in the reaction system were studied. Experiments were conducted under well controlled conditions using specifically designed flow reactor systems. Results demonstrated the low tendency of DMC to form soot compared to other oxygenates and its capacity to contribute to NO reduction under specific fuel-rich conditions. Modeling calculations successfully reproduce reasonably well the experimental trends observed and emphasized the sensitivity of the results to the thermodynamic data of DMC and DMC derived species.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Role of Potassium and Calcium on the Combustion Characteristics of Biomass Obtained from Thermogravimetric Experiments

  • Abián, M.
  • Alzueta, M.U.
  • Carvalho, A.
  • Rabaçal, M.
  • Costa, M.
This work focuses on the combustion behavior of raw and demineralized grape pomace and grape pomace doped with 0.1, 0.5, 0.82 (equal to the K concentration in the raw biomass), 3, and 6 wt % K and 0.1, 0.5, 1.08 (equal to the Ca concentration in the raw biomass), 3, and 6 wt % Ca. To identify the individual role of calcium and potassium, the biomass samples were either pyrolyzed in a N2 atmosphere or oxidized in air in a thermogravimetric analyzer (TGA) during non-isothermal runs at 10 K/min from room temperature to a maximum temperature of 1275 K. In all of the cases, the biomass pyrolysis process shows one main stage associated with the volatile matter release. This process is not significantly affected by the mineral content of biomass nor the presence of high K and Ca contents. During combustion in air, the biomass samples show two main distinct stages that are associated with the volatile matter release and the char oxidation. Whereas the main devolatilization stage is not significantly affected by the mineral content of the biomass, the char oxidation stage is shifted to higher temperatures for the demineralized biomass. Potassium and calcium play a different role on the char oxidation process. In general, char oxidation is promoted with increasing the K content, whereas Ca does not significantly influences this process. The TGA results were also used to determine the kinetic parameters of the pyrolysis and combustion processes of biomass in the presence of K and Ca.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Polycyclic aromatic hydrocarbons (PAHs) and soot formation in the pyrolysis of the butanol isomers

  • Viteri, F.
  • Gracia, S.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M. U.
The formation of polycyclic aromatic hydrocarbons (PAHs) and soot from the pyrolysis of the four butanol isomers: 1-butanol, 2-butanol, iso-butanol and tert-butanol, at three reaction temperatures (1275, 1375 and 1475 K) has been studied. The identification and quantification of the sixteen PAHs, classified by the Environmental Protection Agency (EPA) as priority pollutants, were done using the gas chromatography–mass spectrometry (GC–MS) technique. The soot formed was collected at the reactor outlet. Light gases formed were also quantified. The harmful potential of the PAHs through the benzoa]pyrene equivalent, Ba]P-eq amount, has been evaluated. The main results show that the highest formation of light gases was obtained from the pyrolysis of iso-butanol at 1275 K. The formation of H2 increases significantly as the temperature increases, following the Hydrogen abstraction carbon addition (HACA) route that leads to form PAHs which subsequently form soot. The tendency to soot formation, under the experimental conditions of the present study, is ranked as follows: tert-butanol, 2-butanol, 1-butanol and iso-butanol. The highest PAHs amount and the highest toxic potential, expressed as Ba]P-eq amount, were found in the pyrolysis of all butanol isomers at 1275 K.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Emissions of polycyclic aromatic hydrocarbons during biomass combustion in a drop tube furnace

  • Colom-Díaz, J.M.
  • Alzueta, M.U.
  • Fernandes, U.
  • Costa, M.
The objective of this work is to investigate experimentally the formation of polycyclic aromatic hydrocarbons (PAH) during the combustion of biomass in a drop tube furnace (DTF). A number of biomass fuels, including furniture residues, grape pomace, kiwi residues, olive residues, wheat straw, rice husk and platanus residues were used in this work, with the tests performed at three temperatures (900, 1000 and 1100 °C). The solid fuels feed rate was 23 g/h and the total air flow rate was 4 L/min, ensuring a residence time in the DTF of around 2 s. In order to collect the PAH in the effluent gas, a narrow tube containing XAD-2 resin was connected to the flue gas duct of the DTF. A quartz fiber filter was placed just before it to collect the particulate matter, including soot, present in the flue gas. The analysis and quantification of the PAH combined Soxhlet extraction and gas chromatograph-mass spectrometer. Flue gas concentrations of O2, CO2, CO, hydrocarbons and NOx were measured to gather information regarding the combustion conditions. The results showed two distinct features for the variation of the total PAH emissions: one decreasing with temperature and other with a maximum at 1000 °C. Grape pomace, kiwi residues and platanus residues presented the lowest PAHs emission (20.8–54.2 mg PAH/kg fuel). A direct relation between the total amount of PAHs and the toxic equivalency value was found.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

An experimental and modeling study of the ignition of dimethyl carbonate in shock tubes and rapid compression machine

  • Alexandrino, Katiuska
  • Alzueta, María U.
  • Curran, Henry J.
Ignition delay times of dimethyl carbonate DMC were measured using low- and high-pressure shock tubes and in a rapid compression machine (RCM). In this way, the effect of fuel concentration (0.75% and 1.75%), pressure (2.0, 20, and 40 atm) and equivalence ratio (0.5, 1.0, 2.0) on ignition delay times was studied experimentally and computationally using a chemical kinetic model. Experiments cover the temperature range of 795–1585 K. Several models from the literature were used to perform simulations, thus their performances to predict the present experimental data was examined. Furthermore, the effect of the thermodynamic data of the CH3O(C[dbnd]O)¿ radical species and the fuel consumption reaction CH3O(C[dbnd]O)OCH3 ¿ CH3O(C[dbnd]O)¿ + CH3, on the simulations of the ignition delay times of DMC was analyzed using the different models. Reaction path and sensitivity analyses were carried out with a final recommended model to present an in-depth analysis of the oxidation of DMC under the different conditions studied. The final model uses AramcoMech 2.0 as the base mechanism and includes a DMC sub-mechanism available in the literature in which the reaction CH3O(C[dbnd]O)OCH3 ¿ CH3O(C[dbnd]O)¿ + CH3has been modified. Good agreement is observed between calculated and experimental data. The model was also validated using available experimental data from flow reactors and opposed flow diffusion and laminar premixed flame studies showing an overall good performance.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Gas and soot formed in the dimethoxymethane pyrolysis. Soot characterization

  • Alexandrino De Freitas, Katiuska Ferbel
  • Millera Peralta, Ángela
  • Bilbao Duñabeitia, Rafael
  • Alzueta Anía, María Ujué
The many simultaneous processes occurring within in a diesel engine make difficult a thorough understanding of the mechanisms responsible for reduction of soot and/or NOX when an oxygenated compound is added to diesel fuel. Thus, in order to explore the use of oxygenated compounds as biofuels/additives, it is interesting to study their conversion under well-controlled laboratory conditions, together with kinetic studies that help to interpret and understand the reaction schemes that occur during such processes. The aim of this work has been to contribute to the knowledge of the dimethoxymethane (DMM) pyrolysis, one of the oxygenated compounds proposed in literature as alternative fuel. In this way, the influence of pyrolysis temperature (1075–1475¿K) and inlet fuel concentration (33,333 and 50,000¿ppm DMM) on the sooting propensity of DMM, soot reactivity and its properties is analyzed. Therefore, this work includes pyrolysis experiments under different experimental conditions, focusing on the gas-phase analysis and the soot formation, together with a gas-phase model. Additionally, the interaction of soot with O2 and with NO has been studied, and since soot properties are important on the oxidation rate, selected soot samples have been characterized by different instrumental techniques (elemental analysis, physical adsorption with N2, Transmission Electron Microscopy (TEM), X-Ray Diffraction (XRD), and Raman spectroscopy).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

H2S conversion in a tubular flow reactor: experiments and kinetic modeling

  • Colom Díaz, Juan Manuel
  • Abián, María
  • Ballester, M.Y.
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, Uxue
Oxidation of H2S at atmospheric pressure has been studied under different reaction atmospheres, varying the air excess ratio (lambda) from reducing lambda=0.32) to oxidizing conditions lambda=19.46). The experiments have been carried out in a tubular flow reactor, in the 700-1400¿K temperature range. The concentrations of H2S, SO2 and H2 have been determined and the experimental results have been simulated with a detailed chemical mechanism compiled in the present work. The experimental results obtained indicate that H2S consumption is shifted to lower temperatures as the stoichiometry increases, starting at 925K for reducing conditions and at 700K for the most oxidizing ones. The model reproduces well, in general, the experimental data from the present work, and those from the literature at high pressures. Supported by theoretical calculations, the isomerization of HSOO to HSO2 has been determined as an alternative and possible pathway to the final product SO2, from the key SH+O2 reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ethanol as a Fuel Additive: High-Pressure Oxidation of Its Mixtures with Acetylene

  • Marrodán, Lorena
  • Fuster, Miguel
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
An experimental and modeling study of the oxidation of acetylene-ethanol mixtures under high-pressure conditions (10-40 bar) has been carried out in the 575-1075 K temperature range in a plug-flow reactor. The influence on the oxidation process of the oxygen inlet concentration (determined by the air excess ratio, λ) and the amount of ethanol (0-200 ppm) present in the reactant mixture has also been evaluated. In general, the predictions obtained with the proposed model are in satisfactory agreement with the experimental data. For a given pressure, the onset temperature for acetylene conversion is almost the same independent of the oxygen or ethanol concentration in the reactant mixture but is shifted to lower temperatures when the pressure is increased. Under the conditions of this study, the ethanol presence does not modify the main reaction routes for acetylene conversion, with its main effect being the modification of the radical pool composition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Interaction of diesel engine soot with NO2 and O2 at diesel exhaust conditions. Effect of fuel and engine operation mode

  • Abián, M.
  • Martín, C.
  • Nogueras, P.
  • Sánchez-Valdepeñas, J.
  • Rodríguez-Fernández, J.
  • Lapuerta, M.
  • Alzueta, M.U.
This work shows a study of the reactivity of twelve different types of soot with either NO2 or O2 under reacting conditions typically present in diesel particulate filters (DPFs). The soot samples were obtained from the combustion of four conventional and alternative fuels (diesel, biodiesel and two paraffinic fuels) in a diesel engine bench operated under three different engine operation modes: a typical urban-driving mode and two variations to this mode to assess the effect of the injection settings. The main objective of the work is to relate the oxidative reactivity of the soot to the nature and the origin of each sample. The possible simultaneous elimination of soot and NOx at typical diesel exhaust conditions is examined, as well. The reactivity tests were performed in a laboratory quartz gas flow reactor, discontinuous for the solid. The soot-NO2 interaction was studied with 200 ppm of NO2 at 500 °C and the soot-O2 interaction was studied with 5% O2 at 500 °C and 600 °C. The experimental results were used to determine the time needed for the complete conversion of carbon (t) through the use of the equations of the Shrinking Core Model for solid-gas reactions with decreasing size particle and chemical reaction control. In general, the t values show that the diesel fuel generates a less reactive soot than biodiesel or the alternative paraffinic fuels. In addition, increasing the injection pressure or adding a post-injection to the original injection strategy generates a more reactive soot. These findings point out that there is potential to achieve efficient regeneration processes in DPFs through other fuels than conventional ones and via engine calibration.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High-pressure ethanol oxidation and its interaction with NO

  • Marrodán, L.
  • Arnal, Á.J.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
Ethanol has become a promising biofuel, widely used as a renewable fuel and gasoline additive. Describing the oxidation kinetics of ethanol with high accuracy is required for the development of future efficient combustion devices with lower pollutant emissions. The oxidation process of ethanol, from reducing to oxidizing conditions, and its pressure dependence (20, 40 and 60 bar) has been analyzed in the 500–1100 K temperature range, in a tubular flow reactor under well controlled conditions. The effect of the presence of NO has been also investigated. The experimental results have been interpreted in terms of a detailed chemical kinetic mechanism with the GADM mechanism (Glarborg P, Alzueta MU, Dam-Johansen K and Miller JA, 1998) as a base mechanism but updated, validated, extended by our research group with reactions added from the ethanol oxidation mechanism of Alzueta and Hernández (Alzueta MU and Hernández JM, 2002), and revised according to the present high-pressure conditions and the presence of NO. The final mechanism is able to reproduce the experimental trends observed on the reactants consumption and main products formation during the ethanol oxidation under the conditions studied in this work. The results show that the oxygen availability in the reactant mixture has an almost imperceptible effect on the temperature for the onset of ethanol consumption at a constant pressure, but this consumption is faster for the highest value of air excess ratio (¿) analyzed. Moreover, as the pressure becomes higher, the oxidation of ethanol starts at lower temperatures. The presence of NO promotes ethanol oxidation, due to the increased relevance of the interactions of CH3 radicals and NO2 (from the conversion of NO to NO2 at high pressures and in presence of O2) and the increased concentration of OH radicals from the interaction of NO2 and water.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Escaping undesired gas-phase chemistry: Microwave-driven selectivity enhancement in heterogeneous catalytic reactors

  • Ramirez, A.
  • Hueso, J.L.
  • Abian, M.
  • Alzueta, M.U.
  • Mallada, R.
  • Santamaria, J.
Research in solid-gas heterogeneous catalytic processes is typically aimed toward optimization of catalyst composition to achieve a higher conversion and, especially, a higher selectivity. However, even with the most selective catalysts, an upper limit is found: Above a certain temperature, gas-phase reactions become important and their effects cannot be neglected. Here, we apply a microwave field to a catalyst-support ensemble capable of direct microwave heating (MWH). We have taken extra precautions to ensure that (i) the solid phase is free from significant hot spots and (ii) an accurate estimation of both solid and gas temperatures is obtained. MWH allows operating with a catalyst that is significantly hotter than the surrounding gas, achieving a high conversion on the catalyst while reducing undesired homogeneous reactions. We demonstrate the concept with the CO 2 -mediated oxidative dehydrogenation of isobutane, but it can be applied to any system with significant undesired homogeneous contributions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High pressure study of H2 oxidation and its interaction with NO

  • Colom Díaz, Juan Manuel
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María Uxue
The present study deals with the oxidation of H2 at high pressure and its interaction with NO. The high pressure behavior of the H2/NOx/O2 system has been tested over a wide range of temperatures (500–1100 K) and different air excess ratios (lambda = 0.5–6.4). The experiments have been carried out in a tubular flow reactor at 10, 20 and 40 bar NO has been found to promote H2 oxidation under oxidizing conditions, reacting with HO2 radicals to form the more active OH radical, which enhances the conversion of hydrogen. The onset temperature for hydrogen oxidation, when doped with NO, was approximately the same at all stoichiometries at high pressures (40 bar), and shifted to higher temperatures as the pressure decreases. The experimental results have been analyzed with an updated kinetic model. The reaction NO + NO + O2 <--> NO2 + NO2 has been found to be important at all conditions studied and its kinetic parameters HNO + H2 <--> NH + H2O have been modified, according to its activation energy uncertainty. Furthermore, the kinetic parameters of reaction have been estimated, in order to obtain a good prediction of the oxidation behavior of H2 and NO conversion under reducing conditions. The kinetic model shows a good agreement between experimental results and model predictions over a wide range of conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

CH3SH conversion in a tubular flow reactor. Experiments and kinetic modelling

  • Alzueta, M.U.
  • Pernía, R.
  • Abián, M.
  • Millera, Á.
  • Bilbao, R.
The use of non-conventional fuel sources, such as shale gas, brings new research requisites for its proper use in an environmental friendly manner. In this context, shale gas may include different sulphur containing compounds, such as methanethiol, that is also formed as intermediate during sulphur containing residues processing. The present work includes an experimental and kinetic modelling study of the oxidation of methanethiol, CH3SH, in a quartz flow tubular reactor at atmospheric pressure and in the 300–1400 K temperature range. The influence of the temperature, the O2 concentration and the presence of H2O on the conversion regime of CH3SH and the formation of different compounds has been analysed. The experimental results have been interpreted in terms of a detailed gas-phase mechanism compiled in the present work, and the elementary steps involved in the conversion of CH3SH have been identified. In general, oxidation of CH3SH is favoured by both oxygen level and temperature, while the presence of H2O does not modify the CH3SH conversion profile. The main sulphur containing products are SO2, H2S and CS2, pointing to a significant role of other products, apart from SO2, for the control of pollutant emissions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Study of the conversion of CH4/H2S mixtures at different pressures

  • Colom-Díaz, J. M.
  • Leciñena, M.
  • Peláez, A.
  • Abián, M.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
Due to the different scenarios where sour gas is present, its composition can be different and, therefore, it can be exploited through different processes, being combustion one of them. In this context, this work deals with the oxidation of CH4 and H2S at different pressures and under a wide variety of conditions. The oxidation has been evaluated experimentally in two different flow reactor set-ups, one working at atmospheric pressure and another one operating from atmospheric to high pressures (40 bar). Different CH4/H2S mixtures have been tested, together with different oxygen concentrations and in the temperature range of 500–1400 K. The experimental results obtained show that the oxidation of the CH4/H2S mixtures is shifted to lower temperatures as pressure increases, obtaining the same trends at atmospheric pressure in both experimental set-ups. H2S oxidation occurs prior to CH4 oxidation at all conditions, providing radicals to the system that promote CH4 oxidation to lower temperatures (compared to neat CH4 oxidation). This effect is more relevant as pressure increases. H2S oxidation is inhibited by CH4 at atmospheric pressure, being more noticeable when the CH4/H2S ratio is higher. At higher pressures, the H2S conversion occurs similarly in the absence or presence of CH4. The experimental results have been modeled with an updated kinetic model from previous works from the literature, which, in general, matches well the experimental trends, while some discrepancies between experimental and modeling results at atmospheric pressure and 40 bar are found in the conversion of H2S and CH4.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Joint quantification of PAH and oxy-PAH from standard reference materials (urban dust and diesel particulate matter) and diesel soot surrogate by GC-MS

  • Viteri, Fausto
  • Pezo Piña, Davinson
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María Uxue
The combustion of fossil fuels produces pollutants such as soot, which consists of carbonaceous particles whose emission is regulated by environmental laws. Soot is mainly formed from polycyclic aromatic hydrocarbons (PAH), through different reaction ways and, once formed, it can adsorb PAH on its surface. These compounds have an environmental importance due to their carcinogenic and mutagenic potential. In the last years, the oxygenated derivatives of PAH (oxy-PAH) have also been considered as dangerous since they have been found to be mutagenic for bacterial and human cells. Therefore, the purpose of this work was to quantify simultaneously selected PAH and oxy-PAH from different samples of soot. The quantification method involves Soxhlet extraction and subsequent concentration by rotary evaporation that allows to recover the analysed compounds from soot samples. The PAH and oxy-PAH were identified and quantified, by a single injection, using a gas chromatograph-mass spectrometer (GC-MS). The method showed a good repeatability using a diesel soot surrogate test sample, Printex-U. The validation process showed that most of the compounds are recovered between the values established for the Standard Reference Materials analysed, 1650b and 1649b. The values of the mass fraction of the oxy-PAH obtained in this work showed, in general, a good match with those indicated in other studies.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of H2S on the S-PAH formation during ethylene pyrolysis

  • Adánez-Rubio, I.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
The effect of the H2S presence on the formation of six different sulphurated polycyclic hydrocarbons (S-PAH), during the pyrolysis of ethylene-H2S mixtures, has been studied in a tubular flow reactor installation. Experiments with different inlet H2S concentrations (0.3, 0.5 and 1%) and temperatures of reaction (between 1075 and 1475 K) have been carried out. The 16 compounds that the Environmental Protection Agency (EPA) has stated as EPA-PAH priority pollutants were also analysed. EPA-PAH compounds were the majority of quantified PAH, and also S-PAH were found and quantified. For temperatures studied, the S-PAH/EPA-PAH ratio values showed a maximum value at 1075 K and a minimum value at 1175 K. With respect to the effect of the inlet concentration of H2S, the S-PAH/EPA-PAH ratio values increased with the increase of the H2S concentration.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental and simulation study of the high pressure oxidation of dimethyl carbonate

  • Alexandrino, K.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M. U.
An experimental and modeling study of the oxidation at high pressure of dimethyl carbonate (DMC) has been performed in a quartz tubular flow reactor. Experimental and simulated concentrations of DMC, CO, CO2 and H2 have been obtained for different temperatures (500–1073 K), pressures (20, 40, and 60 atm) and stoichiometries (λ = 0.7, 1, and 35). Both pressure and concentration of oxygen are important parameters for conversion of DMC. The simulations have been carried out using a detailed kinetic mechanism previously developed by the research group. In general, the model is able to reproduce the experimental trends of the different concentration profiles, although some discrepancies are observed between experimental and simulation results. The performance of the model was also evaluated through the simulation of literature data of the oxidation of DMC at atmospheric pressure in a flow reactor and of the DMC ignition delay times under low and high pressures. In this sense, this work contributes to the knowledge of the combustion process of DMC, by providing new experimental data on the conversion of DMC at high pressures and using a kinetic model for the interpretation of the results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The inhibiting effect of NO addition on dimethyl ether high-pressure oxidation

  • Marrodán, L.
  • Arnal, Á.J.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
The high-pressure dimethyl ether (DME, CH3OCH3) oxidation has been investigated in a plug flow reactor in the 450–1050 K temperature range. Different pressures (20, 40 and 60 bar), air excess ratios (¿ = 0.7, 1 and 35), and the absence/presence of NO have been tested, for the first time under these conditions. An early reactivity of DME and a negative temperature coefficient (NTC) zone have been observed under the studied conditions, although under very oxidizing conditions (¿ = 35), NTC zone is almost imperceptible because DME is completely consumed at lower temperatures. A chemical kinetic mechanism has been used to describe the DME high-pressure oxidation, with a good agreement with the experimental trends observed. In general, modeling calculations with the present mechanism have been successfully compared with experimental data from literature. The presence of NO has an inhibiting effect on DME high-pressure consumption at low-temperatures because of: (i) the competition between CH3OCH2+O2¿CH3OCH2O2 and CH3OCH2+NO2¿CH3OCH2O+NO reactions, and (ii) the participation of NO in CH3OCH2O2+NO¿CH3OCH2O+NO2 reaction, preventing CH3OCH2O2 radicals continue reacting through a complex mechanism, which includes a second O2 addition and several isomerizations and decompositions, during which highly reactive OH radicals are generated. Consequently, NO and NO2 are interchanged in a cycle but never consumed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Reactivity and Physicochemical Properties of the Soot Produced in the Pyrolysis of 2, 5-Dimethylfuran and 2-Methylfuran

  • Alexandrino, Katiuska
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
Alkylated furan derivatives, such as 2, 5-dimethylfuran (2, 5-DMF) and 2-methylfuran (2-MF), have shown, at laboratory scale, a relatively high tendency to form soot. However, soot emissions from diesel engines are lower when diesel/2, 5-DMF and diesel/2-MF blends are used. This could indicate that the soot produced in the conversion of these compounds has high reactivity toward some gases present within the combustion chamber, reducing soot emissions in the exhaust gas. In this context, a study on the reactivity and the characterization of the soot generated in the pyrolysis of 2, 5-DMF and 2-MF, under different experimental conditions, was performed in an effort to increase the understanding of the reactivity and physicochemical properties of the soot originating in the conversion of these furan derivatives. The soot samples analyzed were obtained in previous works using different concentrations of the alkylated furan derivatives (5000, 7500, and 15â»000 ppm of 2, 5-DMF, and 9000 and 18â»000 ppm of 2-MF) and at different temperatures (1275, 1375, and 1475 K). The reactivity experiments were performed at 1275 K with 500 ppm of O2 and 2000 ppm of NO in a tubular quartz flow reactor. Different instrumental analysis techniques were employed to characterize the soot samples and to try to link the soot reactivity with its physicochemical properties. The dependence of soot reactivity and properties with soot formation conditions, namely, temperature and inlet fuel concentration, is studied.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

2-methylfuran pyrolysis: Gas-phase modelling and soot formation

  • Alexandrino, Katiuska
  • Baena, Cristian
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
Since the recent discoveries in the high efficiency production methods of 2, 5-dimethylfuran (2, 5-DMF) and 2-methylfuran (2-MF), and due to their good physicochemical properties, these alkylated furan derivatives have been highly considered as fuels or additives in gasoline and diesel engines. However, the cyclic structures of 2, 5-DMF and 2-MF may make them effective soot precursors. We have recently studied the capacity of 2, 5-DMF to form soot under different pyrolysis experimental conditions, in a flow reactor, and we now focus on the study of the capacity of 2-MF to form soot under the same conditions. In this way, a systematic investigation of the temperature and fuel concentration effects on the soot formed in the 2-MF pyrolysis was undertaken, in an atmospheric-pressure flow reactor, in the temperature range of 975–1475 K, and with 9000 and 18, 000 ppm of 2-MF (inlet total carbon of 45, 000 and 90, 000 ppm, respectively). The increase in the soot yield is favoured by the rise in both the temperature and the inlet 2-MF concentration, while the gas yield decreases as the temperature increases without a noticeable influence of the inlet 2-MF concentration. A gas-phase chemical kinetic model was proposed to describe both the pyrolysis of 2-MF and 2, 5-DMF. It was validated against the gas-phase data obtained in this work, as well as with a series of experimental data from literature including shock tube and flow reactors. Results show that 2-MF has a high capacity to form soot, and C4 species play a major role in the formation of intermediates that yield polycyclic aromatic hydrocarbons (PAH), well known as soot precursors. However, the soot yield in the 2-MF pyrolysis was found to be lower than that in the 2, 5-DMF pyrolysis, mainly because, according to modelling results, during the 2, 5-DMF pyrolysis the cyclopentadienyl radicals are highly formed, whose recombination yields directly naphthalene without any other intermediate.