Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Study of ni/al-fe catalyst stability in the aqueous phase hydrogenolysis of glycerol

  • Raso, R.
  • García, L.
  • Ruiz, J.
  • Oliva, M.
  • Arauzo, J.
The present work studied the stability and reusability of Ni/Al-Fe catalyst in the aqueous phase hydrogenolysis of glycerol without external hydrogen addition. The catalyst based on 28 molar % of Ni with 3/1 molar ratio of Al/Fe was prepared through co-precipitation. This catalyst presented the best performance in our last study which compares several Ni/Al-Fe catalysts with different molar ratios of Al/Fe. To see the influence of the pressurized water on the physicochemical characteristics of Ni/Al-Fe catalyst, a test of up to 9 h has been carried out. Fresh and used catalysts were characterized by various techniques: X-ray Diffraction (XRD), N2-physisorption, field emission scanning electron microscopy (FESEM) and STEM. Glycerol conversion and carbon yield to gases and liquids did not vary significantly when compared at 3 h and 9 h. Furthermore, the morphology of the catalyst remains stable after continuous recycling under severe hydrothermal conditions. The nickel rich phase of the catalyst, which was determined by XRD and scanning transmission electron microscopy (STEM) techniques, showed a stable size after 9 h under reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effects of slow-pyrolysis conditions on the products yields and properties and on exergy efficiency: A comprehensive assessment for wheat straw

  • Greco, Gianluca
  • Di Stasi, Christian
  • Rego, Filipe
  • González, Belén
  • Manyà, Joan J.
In the present work, the effects of the peak temperature (400–550 °C), absolute pressure (0.2–0.9 MPa), gas residence time (100–200 s) and reactor atmosphere (pure N2 or a mixture of CO2/N2) on the pyrolysis behavior of wheat straw pellets were investigated. A factorial design of experiments was adopted to assess the effects of the above-mentioned factors on the pyrolysis products, the exergy efficiencies related to them and to the overall process, and the heat required. The pyrolysis energy/exergy assessment is nowadays of great interest, for the scaling of the installations from lab-scale to commercial-scale. Results showed that, as expected, the peak temperature was the most influential factor on the yields and distributions of all the pyrolysis products as well as the char properties related to its potential stability and pore size distribution. However, an increased pressure enhanced the release of the gas species at the expense of the liquid products, without altering the final char yield. The char exergy efficiency was negatively affected by an increase in peak temperature, whereas its effect on the exergy efficiency of the produced gas resulted to be positive. It was also found that pressurized pyrolysis favored the exergy efficiency of the process, even at relatively high pyrolysis peak temperature. For the biomass feedstock and the range of operating conditions studied here, thermodynamic irreversibilities of the pyrolysis system were considerably lowered when the process was conducted at 550 °C, 0.9 MPa and using a mixture of CO2 and N2 as carrier gas at relatively short residence times.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of the Ni-Co/Al-Mg catalyst loading in the continuous aqueous phase reforming of the bio-oil aqueous fraction

  • Lozano, P.
  • Simón, A.I.
  • García, L.
  • Ruiz, J.
  • Oliva, M.
  • Arauzo, J.
The effect of catalyst loading in the Aqueous Phase Reforming (APR) of bio-oil aqueous fraction has been studied with a Ni-Co/Al-Mg coprecipitated catalyst. Because of the high content of water in the bio-oil aqueous fraction, APR could be a useful process to convert this fraction into valuable products. Experiments of APR with continuous feeding of aqueous solution of acetol, butanol and acetic acid as the only compound, together with a simulated and a real aqueous fraction of bio-oil, were carried out. Liquid products in the liquid effluent of the APR model compounds were quantified and the reaction pathways were revised. The increase of catalyst loading produced an increase of gas production and a gas with higher alkanes content. Acetol was the compound with the highest reactivity while the conversion of acetic acid was very low. The presence of acetic acid in the feed caused catalyst deactivation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Effect of H2S on the S-PAH formation during ethylene pyrolysis

  • Adánez-Rubio, I.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M.U.
The effect of the H2S presence on the formation of six different sulphurated polycyclic hydrocarbons (S-PAH), during the pyrolysis of ethylene-H2S mixtures, has been studied in a tubular flow reactor installation. Experiments with different inlet H2S concentrations (0.3, 0.5 and 1%) and temperatures of reaction (between 1075 and 1475 K) have been carried out. The 16 compounds that the Environmental Protection Agency (EPA) has stated as EPA-PAH priority pollutants were also analysed. EPA-PAH compounds were the majority of quantified PAH, and also S-PAH were found and quantified. For temperatures studied, the S-PAH/EPA-PAH ratio values showed a maximum value at 1075 K and a minimum value at 1175 K. With respect to the effect of the inlet concentration of H2S, the S-PAH/EPA-PAH ratio values increased with the increase of the H2S concentration.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Importance of pyrolysis temperature and pressure in the concentration of polycyclic aromatic hydrocarbons in wood waste-derived biochars

  • Greco, Gianluca
  • Videgain, María
  • Di Stasi, Christian
  • Pires, Elisabet
  • Manyà, Joan J.
Biochar addition to soil can lead to potential environmental risks due to its content of polycyclic aromatic hydrocarbons (PAHs). Until now, previous research focused on assessing the influence of pyrolysis peak temperature and feedstock on the formation and evolution of PAHs. Nevertheless, the effects of other important process parameters —such as pressure, gas residence time, and type of carrier gas— have not been comprehensively explored. To fill this gap, a 2-level full factorial design of experiments was conducted to assess the influence of the above-mentioned parameters on the pyrolysis behavior of an untreated wood waste as well as the properties of resulting biochars, including their PAHs contents. Results showed that the highest production of PAHs was reached at lower peak temperatures, whereas an increase in temperature led to a substantial reduction of the final PAHs content. An increased pressure also resulted in a marked decrease in PAHs, probably as a consequence of the higher carrier gas flow rates used under pressurized conditions, which could inhibit the generation of PAHs by condensation and polymerization. The outstanding results obtained from the phytotoxicity assessment for three plant species (barley, watercress, and basil) suggest that PAHs were not the major responsible for the observed short-term phytotoxic effects of biochars, since a considerable part of the phytotoxic compounds in biochar can be removed by a simple water washing step.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Interaction of NH3 and NO under combustion conditions. Experimental flow reactor study and kinetic modeling simulation

  • Alzueta, M.U.
  • Ara, L.
  • Mercader, V.D.
  • Delogu, M.
  • Bilbao, R.
The interaction between ammonia and NO under combustion conditions is analyzed in the present work, from both experimental and kinetic modelling points of view. An experimental systematic study of the influence of the main variables for the NH3sbnd]NO interaction is made using a laboratory tubular flow reactor installation. Experiments are performed at atmospheric pressure and variables analyzed include: temperature in the 700–1500 K range, air stoichiometry, from pyrolysis to very oxidizing conditions, and the NH3/NO ratio, in the 0.7–3.5 range. Nitrogen and argon have been used as diluent gas. A literature reaction mechanism has been used to simulate the present experimental results and discuss the main findings. Reaction path analysis has allowed the identification of the reaction routes under the studied conditions. The simulations reflect the main experimental trends observed. Main results show that NO reduction by NH3 occurs at any conditions studied, but is more intense under oxygen excess conditions. Interactions of NH3 and NO proceeds in a molar basis with optimum conversions of NO of up to almost 100%. © 2021
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Wheat-straw-derived activated biochar as a renewable support of Ni-CeO2 catalysts for CO2 methanation

  • Di Stasi C.
  • Renda S.
  • Greco G.
  • González B.
  • Palma V.
  • Manyà J.J.
Ceria-and urea-doped activated biochars were used as support for Ni-based catalysts for CO2 methanation purposes. Different materials were prepared and tested to find the best catalytic formulation. After several CO2 methanation experiments—carried out at 0.35–1.0 MPa and 300–500¿C—it was found that the most suitable catalyst was a wheat-straw-derived activated biochar loaded with 30 wt.% of CeO2 and 20 wt.% of Ni. Using this catalyst, a CO2 conversion of 65% with a CH4 selectivity of 95% was reached at 1.0 MPa, 400¿C, and 13, 200 h-1 . From the study of the influence of the gas hourly space velocity, it was deduced that the most likely reaction mechanism was a reverse water–gas shift reaction, followed by CO hydrogenation. N-doping of the carbon support as an alternative to the use of ceria was also investigated. However, both CO2 conversion and selectivity toward CH4 values were clearly lower than those obtained for the ceria-containing catalyst cited above. The outcomes of this work indicate that a renewable biomass-derived support can be effectively employed in the catalytic conversion of CO2 to methane. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Biomass-derived carbons physically activated in one or two steps for CH4/CO2 separation

  • Greco, G.
  • Canevesi, R.L.S.
  • Di Stasi, C.
  • Celzard, A.
  • Fierro, V.
  • Manyà Cervelló, J. J.
The present study aims at evaluating the suitability of producing activated carbons (ACs) derived from wheat straw by a one-step synthesis approach, as an alternative to more conventional two steps production processes (i.e., pyrolysis and subsequent activation). The performance of the produced ACs, in one or two steps, as sustainable and selective CO2 adsorbents for CH4/CO2 separation is compared. In addition, the influence of pyrolysis conditions on the properties of the resulting two-step ACs is carefully analyzed. We show that the biochar-based precursors of ACs presenting the best textural properties were obtained under mild conditions of maximum temperature and absolute pressure during pyrolysis. The one-step ACs were fully comparable —in terms of textural properties as well as CO2 uptake and selectivity— to those produced by the more conventional two-step synthesis process. In addition, results obtained from breakthrough curve simulations highlight that the best AC in terms of CH4 recovery under dynamic conditions was produced by a one-step activation. Therefore, the one-step process appears to be as an attractive route for the production of engineered carbon materials, which can lead to significant cost savings in large-scale production systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Plant-derived hard carbon as anode for sodium-ion batteries: A comprehensive review to guide interdisciplinary research

  • Alvira, D.
  • Antorán, D.
  • Manyà, J.J.
Sodium-ion batteries (SIBs) are one of the most promising candidates to replace lithium-ion batteries (LIBs) in grid-scale energy storage applications. SIBs technology is still in an early development stage and new feasible and low-cost active materials are required. The design of high-performance anodes and the fully understanding of the sodium storage mechanisms are the main bottleneck to overcome. Hard carbons (HCs) are extensively studied as anode material since sodium ions can be intercalated in pseudographitic domains and reversibly adsorbed in surface edges, defects and nanopores. This review aims at providing a comprehensive overview of the current state of knowledge of plant-derived HC anodes in SIBs, which can be helpful for researchers from different backgrounds working in the field. Working principles of SIBs are summarized, together with a detailed description of the Na-ion storage mechanisms in hard carbon anodes proposed to date. Finally, an exhaustive literature review on the performance of plant-derived HCs in SIBs is presented, with special focus on the synthesis pathways (including activation and/or doping treatments).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Thermodynamic and physical property estimation of compounds derived from the fast pyrolysis of lignocellulosic materials

  • Fonts, Isabel
  • Atienza-Martinez, Maria
  • Carstensen, Hans-Heinrich
  • Benes, Mario
  • Pinheiro Pires, Anamaria Paiva
  • Garcia-Perez, Manuel
  • Bilbao, Rafael
The development of biomass pyrolysis oil refineries is a very promising path for the production of biofuels and bioproducts from lignocellulosic materials. Given that bio-oil is a complex mixture of organic compounds, the production of valuable bioproducts may imply the use of different separation processes, such as distillation, selective condensation, crystallization based on melting points, liquid-liquid extraction or adsorption, and/or upgrading treatments, such as catalytic cracking or hydrodeoxygenation. In this context, the main objectives of this work are (1) to propose a simple but representative composition of the bio-oil, which can be used as a bio-oil surrogate, and (2) to determine selected thermodynamic, physical, and molecular properties of the organic compounds included in the bio-oil surrogate using different estimation methods and calculation procedures. These properties are critical temperature, critical pressure, critical volume, normal boiling point, enthalpy of vaporization, vapor pressure curves, normal melting point, enthalpy of fusion, heat capacities of gas, liquid, and solid, gas and liquid standard enthalpy of formation, gas standard Gibbs free energy of formation, Hansen solubility parameters, molecular volume, and molecular diameter. This group of properties has been selected for their possible application in the simulation or design of thermochemical, separation, and upgrading processes. Additionally, the suitability of the estimated thermodynamic properties and the proposed surrogate composition has been assessed by comparing experimental and literature data with the apparent enthalpy of formation of the bio-oil predicted from the weight-averaged contributions of the compounds as well as the heat required for the pyrolysis process at 500 °C.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental and Modeling Evaluation of Dimethoxymethane as an Additive for High-Pressure Acetylene Oxidation

  • Marrodán, Lorena
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
The high-pressure oxidation of acetylene–dimethoxymethane (C2H2–DMM) mixtures in a tubular flow reactor has been analyzed from both experimental and modeling perspectives. In addition to pressure (20, 40, and 60 bar), the influence of the oxygen availability (by modifying the air excess ratio, λ) and the presence of DMM (two different concentrations have been tested, 70 and 280 ppm, for a given concentration of C2H2 of 700 ppm) have also been analyzed. The chemical kinetic mechanism, progressively built by our research group in the last years, has been updated with recent theoretical calculations for DMM and validated against the present results and literature data. Results indicate that, under fuel-lean conditions, adding DMM enhances C2H2 reactivity by increased radical production through DMM chain branching pathways, more evident for the higher concentration of DMM. H-abstraction reactions with OH radicals as the main abstracting species to form dimethoxymethyl (CH3OCHOCH3) and methoxymethoxymethyl (CH3OCH2OCH2) radicals are the main DMM consumption routes, with the first one being slightly favored. There is a competition between β-scission and O2-addition reactions in the consumption of both radicals that depends on the oxygen availability. As the O2 concentration in the reactant mixture is increased, the O2-addition reactions become more relevant. The effect of the addition of several oxygenates, such as ethanol, dimethyl ether (DME), or DMM, on C2H2 high-pressure oxidation has been compared. Results indicate that ethanol has almost no effect, whereas the addition of an ether, DME or DMM, shifts the conversion of C2H2 to lower temperatures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Assembly and electrochemical testing of renewable carbon-based anodes in SIBs: a practical guide

  • Alvira, Darío
  • Antorán, Daniel
  • Manyà, Joan J.
Sodium-ion batteries (SIBs) are considered as a promising candidate to replace lithium-ion batteries (LIBs) in large-scale energy storage applications. Abundant sodium resources and similar working principles make this technology attractive to be implemented in the near future. However, the development of high-performance carbon anodes is a focal point to the upcoming success of SIBs in terms of power density, cycling stability, and lifespan. Fundamental knowledge in electrochemical and physicochemical techniques is required to properly evaluate the anode performance and move it in the right direction. This review aims at providing a comprehensive guideline to help researchers from different backgrounds (e.g., nanomaterials and thermochemistry) to delve into this topic. The main components, lab configurations, procedures, and working principles of SIBs are summarized. Moreover, a detailed description of the most used electrochemical and physicochemical techniques to characterize electrochemically active materials is provided.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

An experimental and modeling study of acetylene-dimethyl ether mixtures oxidation at high-pressure

  • Marrodán, Lorena
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
The oxidation of acetylene (as soot precursor) and dimethyl ether (DME, as a promising fuel additive) mixtures has been analyzed in a tubular flow reactor, under high-pressure conditions (20, 40 and 60 bar), in the 450–1050 K temperature range. The effect of varying the air excess ratio (λ≈0.7, 1 and 20) and the percentage of DME with respect to acetylene (10 and 40%) has been analyzed from both experimental and modeling points of view. The addition of DME modifies the composition of the radical pool, increasing the production of OH radicals which cause a shift in the onset temperature for C2H2 conversion to lower temperatures; the higher the amount of DME, the lower the temperature. The presence of DME favors the oxidation of C2H2 towards products such as CO and CO2, eliminating carbon from the paths that lead to the formation of soot. On the other hand, in the presence of C2H2, DME begins to be consumed at temperatures higher than those required for the high-pressure oxidation of neat DME, around 175–200 K more. Consequently, the negative temperature coefficient (NTC) region characteristic of this compound at low temperatures is not observed under those conditions. However, an additional analysis of the influence of DME inlet concentration (at 20 bar and λ=1) indicates that, if the amount of DME in the mixture is increased to 500 ppm and more (700 or 1000 ppm), the reaction pathways responsible for this high DME reactivity at low temperatures become more relevant and the NTC region can now be observed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Conversion of NH3 and NH3-NO mixtures in a CO2 atmosphere. A parametric study

  • Alzueta, María U.
  • Giménez-López, Jorge
  • Mercader, Víctor D.
  • Bilbao, Rafael
The present work addresses the oxidation of ammonia and ammonia-nitric oxide mixtures in a CO2 atmosphere, characteristic of oxy-fuel processes and/or biogas combustion, from both experimental and kinetic modelling points of view. A parametric study of NH3 and NH3/NO mixtures oxidation is carried out, evaluating the influence of the temperature (700–1500 K), stoichiometry (from pyrolysis, λ = 0, to significantly oxidizing conditions, λ = 3.3), gas residence time (low values, 195/T(K) s and high values, 3100/T(K) s) and NH3/NO ratio (0.5–2.2), at atmospheric pressure under well-controlled laboratory conditions using two tubular flow reactor setups. Experimental results have been simulated with an updated literature reaction mechanism, which has been used to interpret the experimental observations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Experimental and simulation study of the high pressure oxidation of dimethyl carbonate

  • Alexandrino, K.
  • Millera, Á.
  • Bilbao, R.
  • Alzueta, M. U.
An experimental and modeling study of the oxidation at high pressure of dimethyl carbonate (DMC) has been performed in a quartz tubular flow reactor. Experimental and simulated concentrations of DMC, CO, CO2 and H2 have been obtained for different temperatures (500–1073 K), pressures (20, 40, and 60 atm) and stoichiometries (λ = 0.7, 1, and 35). Both pressure and concentration of oxygen are important parameters for conversion of DMC. The simulations have been carried out using a detailed kinetic mechanism previously developed by the research group. In general, the model is able to reproduce the experimental trends of the different concentration profiles, although some discrepancies are observed between experimental and simulation results. The performance of the model was also evaluated through the simulation of literature data of the oxidation of DMC at atmospheric pressure in a flow reactor and of the DMC ignition delay times under low and high pressures. In this sense, this work contributes to the knowledge of the combustion process of DMC, by providing new experimental data on the conversion of DMC at high pressures and using a kinetic model for the interpretation of the results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

CO assisted NH3 oxidation

  • Alzueta, María U.
  • Salas, Iris
  • Hashemi, Hamid
  • Glarborg, Peter
In the present work, experimental results from the literature on the effect of CO on the NH oxidation in the absence and presence of NO are supplemented with novel flow reactor results and interpreted in terms of a detailed chemical kinetic model. The kinetic model provides a satisfactory prediction over a wide range of conditions for oxidation in flow reactors and for flame speeds of CO/NH. With increasing levels of CO, the generation of chain carriers gradually shifts from being controlled by the amine reaction subset to being dominated by the oxidation chemistry of CO, facilitating reaction at lower temperatures. At elevated temperature, presence of CO causes a change in selectivity of NH oxidation from N to NO. The present work provides a thorough evaluation of the amine subset of the reaction mechanism for the investigated conditions and offers a kinetic model that reliably can be used for post-flame oxidation modeling in engines and gas turbines fueled by ammonia with a hydrocarbon or alcohol as co-fuel.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Antioxidant additives produced from Argan shell lignin depolymerization

  • Afailal, Zainab
  • Gil-Lalaguna, Noemi
  • Torrijos, María Teresa
  • Gonzalo, Alberto
  • Arauzo, Jesús
  • Sánchez, José Luis
The present work summarizes the results of an experimental study focused on producing antioxidant additives for biofuels from argan shell lignin. The generation of this waste has noticeably increased in specific regions of Morocco as a result of the upward trend in the production of argan oil. Lignin extracted from argan shells via a semi-chemical pulping process was depolymerized under hydrothermal conditions in a stirred autoclave reactor at a temperature range of 250-350 °C. Lignin conversion to phenolic compounds was conducted in subcritical water together with different reaction medium (H2, CO2, and HCOOH). The organic fraction in the aqueous liquid product was extracted and blended with biodiesel at a dosage of 1 wt % to evaluate its antioxidant potential. According to the obtained results, the biodiesel oxidation stability time was drastically improved up to 400%. The depolymerization temperature was observed as a critical factor in the antioxidant potential of the additives, showing a maximum value at 300 °C, regardless of the reaction medium. An extensive characterization of the produced additives was performed. The phenolic monomers present in the produced additives were identified using gas chromatography-mass spectrometry, finding a notable presence of catechol, especially in the additives obtained at 300 °C, which led to the best results of biodiesel oxidation stability. Gel permeation chromatography analyses of the additives also showed a well dissolution of relatively big molecules (up to 7000 Da) in biodiesel. More efforts are required to verify the actual antioxidant potential of these types of molecules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Thermochemical valorization of argan nutshells: Torrefaction and air–steam gasification

  • Afailal, Zainab
  • Gil-Lalaguna, Noemí
  • Fonts, Isabel
  • Gonzalo, Alberto
  • Arauzo, Jesús
  • Sánchez, José Luis
The upswing of argan’s oil for the cosmetic industry has increased the farming of this plant and originated an unexplored residue of complex treatment, its nutshells. This work deals with the characterization of this feedstock, its pretreatment via torrefaction and its gasification either with or without the pretreatment stage. Torrefaction was carried out in a continuous auger reactor at two temperatures, 220 and 250 °C. Hemicellulose was almost totally removed from argan nutshells after torrefaction. Compared to the raw argan shells, the torrefied solids showed an increased content of fixed carbon, a noticeable reduction in the O/C ratio and a significant increase in the HHV, the higher the torrefaction temperature. Chemical thermodynamic equilibrium calculations were implemented to the gasification stage to calculate the equivalence ratio for auto-thermal operation and to assess the effect of temperature and steam-to-biomass ratio on gas yield and composition. Air-steam gasification was also experimentally tested for the raw and torrefied materials at the operational conditions drawn from the simulation results. The torrefied material gasification yielded four times more char than the raw material, while tar production from the torrefied material was only reduced in the presence of steam (anyway starting from a low value: 0.7 g/m3STP for raw argan shells vs 0.3 g/m3STP for the torrefied material). Nor gas production, neither the H2/CO ratio nor the energy content in syngas were improved by gasifying the torrefied material, so torrefaction does not appear to be a profitable pretreatment stage for the gasification of argan nutshells from the point of view of syngas quality.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Aqueous phase hydrogenolysis of glycerol with in situ generated hydrogen over Ni/Al3Fe1 catalyst: effect of the calcination temperature

  • Raso, Raquel
  • Lete, Alejandro
  • García, Lucía
  • Ruiz, Joaquín
  • Oliva, Miriam
  • Arauzo, Jesús
The present work studied the influence of the calcination temperature on the aqueous phase hydrogenolysis of glycerol with in situ generated hydrogen over a Ni/Al3Fe1 catalyst. The Ni/Al3Fe1 catalyst was synthesized by the co-precipitation method at 28 mol% of Ni (Ni/(Ni + Al + Fe)) and a molar ratio of Al/Fe of 3/1. The prepared catalyst was calcined at different temperatures (500–750 °C). The obtained samples were tested for the aqueous phase hydrogenolysis (APH) of glycerol and characterized by several analytical techniques (ICP-OES, H2-TPR, XRD, N2-physisorption, NH3-TPD, STEM, FESEM, and TGA). The catalyst calcined at 625 °C was selected as the best sample due to its high acidity, metal dispersion, and catalytic activity; 1,2-propanediol was the highest carbon selectivity product. In addition, it experienced lower metal leaching than the catalyst calcined at 500 °C
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Waste hemp hurd as a sustainable precursor for affordable and high-rate hard carbon-based anodes in sodium-ion batteries

  • Antorán, D.
  • Alvira, D.
  • Peker, M. E.
  • Malón, H.
  • Irusta, S.
  • Sebastián, V.
  • Manyà, J. J.
The present study reports the promising potential of waste hemp-hurd-derived carbons as anodes in sodium-ion batteries (SIBs). Carbons were produced through an easily scalable process consisting of pyrolysis of raw biomass at 500 °C followed by mild chemical activation of the resulting char through wet impregnation with K2CO3 and subsequent heating of the solid phase (after filtration and drying) up to 700 or 800 °C under nitrogen. The best electrochemical performance was observed for the hard carbon activated at a char-K2CO3 mass ratio of 1:4 and heated up to 800 °C, which exhibited an excellent initial coulombic efficiency (73%) and achieved reversible charge capacities of 267 and 79 mAh g–1 at 0.03 and 1 A g–1, respectively. This material also exhibited an impressive cyclic stability and rate capability, with a capacity retention of 96% after 300 cycles at a current density of 2 A g–1. This more than satisfactory performance could be related to the textural and structural features of the hard carbon, which include moderate interconnected microporosity (with pore sizes below 1 nm), an appropriate concentration of defects in the carbon structure, relatively large interplanar distances, and a certain number of closed pores.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Production of Antioxidant Additives and High-quality Activated Biochar from Pyrolysis of Argan Shells

  • Afailal, Zainab
  • Gil-Lalaguna, Noemí
  • Macías, Robert J.
  • Gonzalo, Alberto
  • Sánchez, José Luis
An integral valorization route based on a pyrolysis process has been proposed to find sustainable applications for argan shells focused on the simultaneous production of activated biochar and antioxidant additives from bio-oil. The bio-oil obtained in the pyrolysis process was furtherly upgraded (hydrothermal treatment and extraction process) to obtain antioxidant additives. On the other hand, the biochar obtained in the pyrolysis was used as a feedstock to produce high-quality activated biochar (by physical activation with CO2). The increase in the pyrolysis temperature (350–550 °C) hardly affected the pyrolysis products distribution (biochar yields of 28–34 wt.% and bio-oil yields between 51 and 55 wt.%), but it led to a slight decrease in the content of phenolic monomers extracted from bio-oil (from 63 wt.% at 350 °C to 53 wt.% at 550 °C). When these extracted fractions were blended with biodiesel (<1 wt.%), improvements of up to 300% in biodiesel oxidation stability were attained. The hydrothermal treatment of the bio-oil did not show noteworthy effects either on the production or antioxidant performance of the extracted fractions if compared with the fractions extracted from the raw bio-oil. Regarding the valorization of argan shells biochar, the activated biochar prepared from it showed considerable potential as an adsorbent material for CO2 (125 mg of CO2 per g of the activated biochar) or phenols (complete removal of 99.6% in 4 h of contact time). It was characterized by a high BET surface area (up to 1500 m2/g), a high carbon content (up to 95 wt.%), low ash content (around 2 wt.%), and a pH of around 8.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

A combined experimental and modeling study on isopropyl nitrate pyrolysis

  • Vin, Nicolas
  • Carstensen, Hans-Heinrich
  • Herbinet, Olivier
  • Bourgalais, Jérémy
  • Alzueta, María Ujué
  • Battin-Leclerc, Frédérique
Alkyl nitrates thermally decompose by homolytic cleavage of the weak nitrate bond at very low temperatures (e.g., around 500 K at reaction times of a few seconds). This provides the opportunity to study the subsequent chemistry of the initially formed radical (or its subsequent pyrolysis products, if unstable) and nitrogen dioxide at such mild conditions. In this work this idea is applied to isopropyl nitrate (iPN) pyrolysis, which is studied in a tubular reactor at atmospheric pressure, temperatures ranging from 373 to 773 K, and residence times of around 2 s. At the experimental conditions, iPN decomposition starts at 473 K with O–N bond fission producing isopropoxy radical (i-C3H7O) and NO2. i-C3H7O is rapidly converted to acetaldehyde (CH3CHO), which is the most abundant product detected, and methyl radicals. Other major products detected are formaldehyde (CH2O), methanol (CH3OH), nitromethane (CH3NO2), NO, methane, formamide (CHONH2), and methyl nitrite (CH3ONO). Four literature nitrogen chemistry models─three of those augmented with iPN specific reactions─have been tested for their ability to predict the iPN decomposition and product profiles. The mechanism by the Curran group performs best, but it still underpredicts the observed high formaldehyde and methanol yields. A rate analysis indicates that the branching ratio of the reaction between methyl radicals and nitrogen dioxide is of significant importance. Based on recent theoretical and experimental data, new rate expressions for the two reactions CH3 + NO2 → CH3O + NO and CH3 + NO2 + He → CH3ONO2 + He are calculated and incorporated in the kinetic models. It is shown that this change clearly improves the predictions, although additional work is needed to achieve good agreement between calculated and measured species profiles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Aqueous phase hydrogenolysis of glycerol over Ni/Al-Fe catalysts without external hydrogen addition

  • Raso, R.
  • García, L.
  • Ruiz, J.
  • Oliva, M.
  • Arauzo, J.
The present work studied the aqueous phase hydrogenolysis (APH) of glycerol (a by-product of biodiesel manufacturing) without external hydrogen addition to produce value-added products. A series of catalysts based on 28 molar % of Ni were prepared through co-precipitation by changing the Al/Fe molar ratio. The calcined and used catalysts were characterized by several techniques (ICP-OES, N2-physisorption, XRD, H2-TPR, NH3-TPD, FESEM and STEM). This work examines the effects of the molar ratio of Al/Fe on the physicochemical characteristics of Ni/Al-Fe catalysts and during the APH of glycerol. All the catalysts showed low carbon yields to gases and high carbon yields to liquid products, mainly 1, 2-propanediol, acetol and ethylene glycol. Ni/Al3Fe1 catalyst gave the best performance in the APH of glycerol: the highest glycerol conversion (42.31 %), carbon yield to gases (6.57 %) and carbon yield to liquids (30.45%). 1, 2-propanediol was the liquid product with the highest carbon selectivity (70.89%).
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

An insight into the separation of 1, 2-propanediol, ethylene glycol, acetol and glycerol from an aqueous solution by adsorption on activated carbon

  • Fortea J.
  • García L.
  • Ruiz J.
  • Oliva M.
  • Arauzo J.
Glycerol conversion processes such as aqueous phase reforming and hydrogenolysis generate value-added compounds highly diluted in water. Because distillation is a high energy demand separation step, adsorption could be an attractive alternative to recover these chemicals. Adsorption isotherms of 1, 2-propanediol, acetol, ethylene glycol and glycerol onto activated carbon were determined by batch adsorption experiments. These isotherms were fitted slightly better to the Freundlich equation than to the Langmuir equation. Acetol is the compound with the highest adsorption at concentrations smaller than 1 M. Properties of the adsorbate such as the -OH group number, chain length, molecular size and dipole moment, besides characteristics of the adsorbent such as the surface area, oxygen and ash content, are considered to explain the observed results. Moreover, adsorption experiments were performed with mixtures of compounds and it was determined that the molar amount adsorbed is less than predicted from the adsorption isotherms of the individual compounds treated separately. In addition, the influence of the activated carbon thermal pretreatment temperature on the adsorption capacity has been studied, the optimum being 800¿C. An analysis of the influence of the activated carbon characteristics showed that the most important parameters are the total pore volume and the ash content. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Optimization of the operating conditions for steam reforming of slow pyrolysis oil over an activated biochar-supported Ni–Co catalyst

  • Di Stasi, C.
  • Cortese, M.
  • Greco, G.
  • Renda, S.
  • González, B.
  • Palma, V.
  • Manyà, J.J.
Highly performing activated biochar-based catalysts were produced for steam reforming of slow pyrolysis oil. The raw biochar obtained from the slow pyrolysis step was physically activated with CO2 at 700 °C and 1.0 MPa and then employed as support. Preliminary tests on steam reforming of acetic acid at 600 °C showed that using activated biochar-supported catalysts containing 10 wt % Ni and 7 wt % Co led to a conversion above 90% with a relatively slow deactivation rate. When a representative organic model compounds mixture was used as feed, relatively fast deactivation of the catalyst was observed, probably due to the adsorption of heavy organic compounds, which could subsequently react to form not easily desorbable reaction intermediates. However, the dual Ni–Co catalysts exhibited a good performance during the steam reforming of a real slow pyrolysis oil at 750 °C, showing long stability and a constant carbon conversion of 65%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Accounting for molecular flexibility in photoionization: case of tert-butyl hydroperoxide

  • Bourgalais, J.
  • Jiang, Z.
  • Bloino, J.
  • Herbinet, O.
  • Carstensen, H. -H
  • Garcia, G. A.
  • Arnoux, P.
  • Tran, L. -S
  • Vanhove, G.
  • Nahon, L.
  • Battin-Leclerc, F.
  • Hochlaf, M.
tert-Butyl hydroperoxide (tBuOOH) is a common intermediate in the oxidation of organic compounds that needs to be accurately quantified in complex gas mixtures for the development of chemical kinetic models of low temperature combustion. This work presents a combined theoretical and experimental investigation on the synchrotron-based VUV single photon ionization of gas-phase tBuOOH in the 9.0 - 11.0 eV energy range, including dissociative ionization processes. Computations consist of the determination of the structures, vibrational frequencies and the energetics of neutral and ionic tBuOOH. The Franck-Condon spectrum for the tBuOOH+ (X+) + e- ¿ tBuOOH (X) + h¿ transition is computed, where special treatment is undertaken because of the flexibility of tBuOOH, in particular regarding the OOH group. Through comparison of the experimental mass-selected threshold photoelectron spectra with explicitly correlated coupled cluster calculations and Franck-Condon simulations that account for the flexibility of the molecule, an estimation of the ionization energy is given. The appearance energy of the only fragment observed within the above-mentioned energy range, identified as the tert-butyl C4H9+, is also reported. Finally, the signal branching ratio between the parent and the fragment ions is provided as a function of photon energy, essential to quantify tBuOOH in gas-phase oxidation/combustion experiments via advanced mass spectrometry techniques.