Skip to main content

DEMOSTRADORES TECNOLOGICOS DE FILTROS Y MULTIPLEXORES CON RESPUESTAS SELECTIVAS Y SINTONIZABLES EN NUEVAS GUIAS COMPACTAS PARA APLICACIONES ESPACIALES

TEC2016-75934-C4-1-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 53
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Multilayer Filter in Empty Substrate Integrated Waveguide With Transmission Zeros

  • Belenguer Martínez, Ángel
  • Fernández-Berlanga, Marcos D
  • Ballesteros, José A.
  • de Dios, Juan J.
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The empty substrate integrated waveguide (ESIW) technology is recently receiving special attention, since it preserves the many advantages of SIW circuits but provides an enhanced behavior due to avoidance of dielectric filling. Many circuits have been designed in the ESIW technology, including several filters with different performances. The next challenge is to achieve the maximum possible compactness degree for these circuits. In this paper, we present the design of a multilayer empty substrate integrated filter with the same performance as if it were manufactured in a single layer but significantly increasing its compactness and mechanical resistance., This work was supported by the Ministerio de Economia y Competitividad, Spanish Government, under Grant TEC2016-75934-C4-3-R and Grant TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Implementing Quasi-Elliptic Microstrip Filters Using Terminating Half Sections

  • Marín-Martínez, Sandra
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This letter presents a technique for the introduction of transmission zeros (TZs) using half section matched terminations for implementing high selectivity filters in planar technology. The proposed technique does not require any cross coupling between nonadjacent resonators or multiple signal paths, and it can be easily incorporated on any planar filter using lumped, quasi-lumped, and/or distributed elements depending on the desired response. Two different bandpass filter topologies are employed for applying the proposed technique. Both prototypes are designed, manufactured, and measured. The measured results show that the TZs can be independently located very close to the passband edges, without degrading the original filter response., This work was supported by the Spanish Ministry of Economy, Industry and Competitiveness under Grant TEC2013-48036-C3-3-R and Grant TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Slotted ESIW Antenna with high efficiency for a MIMO Radar Sensor

  • Miralles-Navarro, Enric
  • Belenguer Martinez, Angel
  • Mateo Sotos, Jorge
  • Torres Aranda, Ana María
  • Lucas Borja, Alejandro
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper introduces a slotted empty substrate integrated waveguide (ESIW) antenna for a multiple-input multiple-output (MIMO) radar sensor. The proposed system is based on the MIMO radar architecture. Orthogonal signals are sent from the transmitters, in such a manner that a MIMO image reconstruction is possible. The presented system application targets the surveillance of strategic areas in gas pipelines and nuclear plants. ESIW technology enables a high-efficiency, low-profile, and compact antenna for these MIMO systems. The fabricated device includes a transition to microstrip line, and, in consequence, the antenna can be integrated with the rest of the system in a standard integrated circuit. The slotted ESIW antenna design and measured results for the targeted application are presented in this paper. The measured results present a gain greater than 15 dBi and return loss below ¿13 dB over the targeted frequency band of operation (16¿16.5 GHz). To the best of the authors¿ knowledge, this is the first slotted ESIW antenna reported in the scientific literature up to now., This work was supported by the Ministerio de Economia y Competitividad, Spanish Government, under research projects TEC2016-75934-C4-3-R and TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Waveguide Quadruplet Diplexer for Multi-Beam Satellite Applications

  • Ossorio García, Javier
  • Melgarejo Lermas, Juan Carlos
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The objective of this paper is to describe the design of an innovative and low-cost diplexer for Ka-band multi-beam satellite applications. The device is based on the use of two quadruplets to implement a number of transmission zeros (TZs) thus obtaining high-selectivity quasi-elliptic transfer functions. The resulting diplexer structure is particularly flexible in terms of layout, does not require tuning and has an excellent high-power behavior. In addition to theory, we compare the results of our simulations with the measurements obtained with a manufactured breadboard. The comparison shows excellent agreement thereby fully validating both the design procedure, and the new diplexer structure., This work was supported in part by the MINECO (Spanish Government) through Research and Development Project under Grant TEC2016-75934-C4-1-R, and in part by the Research and Development Technicians under Grant PTA2015-10839-I.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Combline Filter Embedded in a Bed of Nails

  • Baquero Escudero, Mariano|||0000-0001-8772-5431
  • Valero-Nogueira, Alejandro|||0000-0001-9296-4162
  • Ferrando-Rocher, Miguel|||0000-0003-4098-7180
  • Bernardo-Clemente, Bernardo|||0000-0002-2781-7382
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, we propose a compact topology for high-frequency bandpass filters using coaxial cavities embedded in a bed of nails, including a complete design procedure combining equivalent circuit models and full-wave simulators. The resonance generated around a shortened cylindrical nail of the bed hosting structure is used as the basic element of the proposed filter, which is fed through groove gap waveguides. For design purposes, an equivalent circuit model of the considered resonance is first obtained, and then the coupling levels between resonators are recovered with the distance between adjacent shortened nails. In order to validate the proposed structure and its design procedure, a filter prototype with a bandpass response (centered at 30 GHz and with relative bandwidth of 1.7%) has been designed, manufactured, and measured. Good experimental results, in terms of insertion losses (with a minimum value of 1.6 dB) and return losses (greater than 16.6 dB in the whole passband), have been achieved., This work was supported in part by the Spanish Government, Ministry of Economy, National Program of Research, Development and Innovation through the project SATCOM-KA "New antennas for mobile satellite communications in Ka-band" under Project TEC2016-79700-C2-1-R and in part by the "Demostradores tecnologicos de filtros y multiplexores con respuestas selectivas y sintonizables en nuevas guias compactas para aplicaciones espaciales" under Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An Efficient Technique to Assess the Convergence of the Multimode Equivalent Network for Waveguide Devices

  • Gomez Molina, Celia
  • Quesada Pereira, Fernando
  • Alvarez Melcon, Alejandro
  • Guglielmi, Marco
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Numerical methods are widely used to analyze and design microwave components for communication applications.In the implementation of any numerical technique, however, there are always a set of parameters that must be properly adjusted in order to obtain, at the same time, computational efficiency and numerical accuracy of the results. In this context, therefore, we focus in this paper on the multimode equivalent network formulation for waveguide devices, and we propose a more intuitive and efficient strategy for choosing these parameters. Following our approach, setting only one global numerical variable is sufficient to adjust automatically the specific convergence parameters of each discontinuity to give a specific level of numerical accuracy of the results. As a consequence, the computational efficiency is significantly increased. In addition, the user experience is significantly improved since our approach eliminates all lengthy convergence tests previously needed to assure good numerical accuracy. In addition to theory, we discuss in this paper a number of numerical results that clearly demonstrate how the new strategy is very effective, thereby fully validating the theoretical formulation., This work was supported in part by the Spanish Government through the Ministerio de Educacion, Cultura y Deporte under Grant FPU15/02883, in part by the Ministerio de Economia y Competitividad through the sub-projects 4 and 1 of the coordinated project under Grant TEC2016-75934-C4-R, and in part by the Fundacion Seneca de la Region de Murcia under Grant 19494/PI/14 and Grant 20147/EE/17.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Microstrip to Empty Substrate Integrated Coaxial Line Transition

  • Quiles, Ferran
  • Belenguer Martínez, Ángel
  • Martínez-Zamora, Juan Ángel
  • Nova-Giménez, Vicente
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Substrate integrated waveguides are increasingly being used due to their capability of combining the advantages of planar circuits and traditional waveguides. The development of empty substrate integrated waveguides has substantially reduced the related insertion losses, since waves propagate through air instead of propagating through a lossy dielectric medium. Recently, a new empty coaxial structure, completely built with printed circuit boards and integrated in a substrate, has been proposed. It has been named empty substrate integrated coaxial Line (ESICL). The resulting coaxial line has low cost, easy manufacturing, low radiation, low losses, high-quality factor, and is non dispersive. A transition from grounded coplanar waveguide to ESICL already exists. In this work, a transition from microstrip to ESICL is presented for the first time. In order to demonstrate its feasibility, a back-to-back structure and a bandpass filter have been manufactured and measured., This work was supported by the Ministerio de Economia y Competitividad, Spanish Government, under Research Project TEC2016-75934-C4-3-R and Research Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental Validation of Multipactor Effect for Ferrite Materials Used in L- and S-Band Nonreciprocal Microwave Components

  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Reglero Mangada, Marta Sofía|||0000-0002-3811-843X
  • Melgarejo-Lermas, Juan Carlos
  • GUGLIELMI, MARCO
  • Moreno Cambroreno, María del Rocío
  • Mata-Sanz, Rafael
  • Montero, Isabel
  • Gonzalez Iglesias, Daniel
  • GIMENO MARTINEZ, BENITO
  • Gomez, Alvaro
  • Vegas, Ángel
  • RABOSO GARCÍA-BAQUERO, DAVID
[EN] This paper reports on the experimental measurement of power threshold levels for the multipactor effect between samples of ferrite material typically used in the practical implementation of L-and S-band circulators and isolators. For this purposes, a new family of wideband, nonreciprocal rectangular waveguide structures loaded with ferrites has been designed with a full-wave electromagnetic simulation tool. The design also includes the required magnetostatic field biasing circuits. The multipactor breakdown power levels have also been predicted with an accurate electron tracking code using measured values for the secondary electron yield (SEY) coefficient. The measured results agree well with simulations, thereby fully validating the experimental campaign., This work was supported in part by the European Space Agency (ESA) through the Research Project Novel Investigation in Multipactor Effect in Ferrite and Other Dielectrics Used in High Power RF Space Hardware under Contract AO 1-7551/13/NL/GLC, in part by the Ministerio de Economia y Competitividad (Spanish Government) through Research and Development under Project TEC2016-75934-C4-1-R and Project TEC2016-75934-C4-2-R, and in part by the European Regional Development Fund under Project TEC2014-55463-C3-3-P.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Improved low reflection transition from microstrip line to empty substrate integrated waveguide

  • Esteban González, Héctor|||0000-0002-5936-658X
  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Belenguer, Ángel
[EN] Substrate-integrated waveguides (SIWs) maintain the advantages of planar circuits (low loss, low profile, easy manufacturing, and integration in a planar circuit board) and improve the quality factor of filter resonators. Empty substrateinte-grated waveguides (ESIWs) substantially reduce the insertion losses, because waves propagate through air instead of a lossy dielectric. The first ESIW used a simple tapering transition that cannot be used for thin substrates. A new transition has recently been proposed, which includes a taper also in the microstrip line, not only inside the ESIW, and so it can be used for all substrates, although measured return losses are only 13 dB. In this letter, the cited transition is improved by placing via holes that prevent undesired radiation, as well as two holes that help to ensure good accuracy in the mechanization of the input iris, thus allowing very good return losses (over 20 dB) in the measured results. A design procedure that allows the successful design of the proposed new transition is also provided. A back-to-back configuration of the improved new transition has been successfully manufactured and measured., This work was supported in part by the Ministerio de Economia y Competitividad, Spanish Goverment, under Grant TEC2013-47037-C05-3-R and Grant TEC2013-47037-C05-1-R, and in part by the Ministerio de Educacion, Cultura y Deporte under the Fellowship Program for Training University Professors under Grant FPU14/00150.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Space Qualification of Metalized Additive Manufactured Filters

  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Nova-Giménez, Vicente
  • Ferrer, Álvaro
[EN] The space industry is seeking new solutions for the development of lightweight, inexpensive and easy-to-manufacture on-board communication payload devices. One of the proposed technologies is additive manufacturing (AM) of polymeric materials that are subsequently metallized. The devices developed using this technique must be operational in the particular space environment conditions. In this work we study the integrity of filters made by additive manufacturing against the extreme conditions of mechanical stress, temperature and power management as described in the standard of the European Space Agency (ESA) for satellite payload. To carry out this qualification for space, two types of X-band filters with identical frequency responses have been designed and manufactured: a classic H-plane waveguide cavities filter, and three filters on surface-mount technology (SMT). Two of the SMT filters are low height rectangular cavities filters, while the third one is a high circular cavities filter. This selection was intended to verify that the AM technique offered good results regardless of the devices topology. Two mechanical vibration tests were performed: sinusoidal sweep and random vibration. These tests emulate the transport and launching conditions of the satellite payload. Furthermore, it was measured the mechanical natural frequency of the filters, and its variation after being exposed to the tests in order to evaluate their physical integrity. The thermal analysis was performed emulating the temperature profile experienced by the satellite payload during working conditions. Then, the power handling tests were carried out. The secondary electron emission yield of the material (metallized polymer) was firstly measured. The power levels, location and frequency at which a multipactor discharge would occur were analyzed for both, low-height and standard-height, filters. Finally, both filters were subjected to those power levels, under high vacuum conditions, to check if the said multipactor discharges occurred. The mechanical stress and temperature tests prove that the developed filters can survive the hard launching and operation conditions of commercial satellite payloads. The multipactor tests report the high power levels that the devices can handle without risk of radiofrequency (RF) breakage. All these tests allow to fully qualify the proposed manufacturing technique for spatial applications., This work was supported in part by the Agencia Valenciana de la Innovacion Research Project under Grant INNVA1/2020/84; in part by the Agencia Estatal de Investigacion, Spain, through the Fellowship for Training PhDs under Grant BES-2017-079728; and in part by the Ministerio de Ciencia e Innovacion (MICIN), Spanish Government through the Research and Development Project PID2019-103982RB-C41 under Grant MICIN/AEI/10.13039/501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Design and Performance of a High-Q Narrow Bandwidth Bandpass Filter in Empty Substrate Integrated Coaxial Line at Ku-Band

  • Lucas Borja, Alejandro
  • Belenguer, Angel
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This letter presents the design and performance of a planar narrow bandwidth bandpass filter with high quality factor. The structure is composed of an empty substrate integrated coaxial line with the center conductor suspended in air. The component dimensions have been calculated by means of classical microwave filter design theory. The filter has been manufactured using standard printed circuit board fabrication processes. A measured insertion loss of 1.59 dB, 2.93% fractional bandwidth, and a Q-factor of 1505 have been obtained at 15 GHz. A Q-factor comparison with other substrate and empty substrate integrated technologies shows the advantages of the solution considered in this letter. The proposed filter proves to be suitable for the implementation of integrated microwave or millimeterwave subsystems with severe restrictions, i.e., low in-band losses, very narrow bandpass responses, low frequency dispersion, high out-of-band rejection, and low manufacturing cost., This work was supported by the Ministerio de Ciencia e Innovacion, Spanish Goverment, under Project TEC2016-75934-C4-X-R and Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Folded Bandpass Filter in Empty Substrate Integrated Coaxial Line at S-Band

  • Martinez, Leticia
  • Belenguer, Angel
  • Borja, Alejandro L.
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This letter presents a novel compact folded bandpass filter in empty substrate integrated coaxial line (ESICL) technology. To obtain these compact filters, the inverters are modified to provide a 180 degrees bend when inserted in an ESICL. As a result, the proposed filter has a more compact topology based on parallel resonators. A sixth-order Chebyshev bandpass filter operating at 3 GHz has been designed, manufactured, and measured to experimentally validate this new folded configuration. The length of the novel compact filter has been reduced by 82.2% with respect to an equivalent in-line filter, obtaining very similar results in terms of electrical response., This work was supported in part by the Ministerio de Economia y Competitividad, Spanish Government through Research Projects under Grant TEC2016-75934-C4-3-R and Grant TEC2016-75934-C4-1-R and in part by the Ministerio de Ciencia, Innovacion y Universidades through the Fellowship Program for Training University Professors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Empty SIW Technologies: A Major Step Toward Realizing Low-Cost and Low-Loss Microwave Circuits

  • Belenguer, Angel
  • Borja, Alejandro L.
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Substrate-integrated circuits (SICs) [1] have attracted much attention in the last several years because of their great potential. The first implementation of the concept can be found in [2] as a feeding mechanism for a slot array antenna. Deslandes and Wu [3], [4] used the term substrate-integrated waveguide (SIW) to define this waveguide integrated in a substrate where the lateral walls are synthesized with metallized via holes, and the upper and lower walls are the top and bottom metallization of the substrate. Many other SICs have been developed since the appearance of the SIW. In the substrate-integrated slab waveguide [5], the guide is synthesized on a substrate by cutting an air hole in the center of an SIW, and the frequency operating bandwidth is increased. The ridge SIW [6] also increases the operation bandwidth by drilling cylindrical air holes in the middle of the SIW. The substrate-integrated nonradiative dielectric waveguide [7] uses a specific pattern of air holes as lateral walls, creating a dielectric waveguide channel that reduces the radiation losses with respect to the SIW. The half-mode SIW [8] reduces the size of the SIW by half by exploiting the fact that there is a symmetry plane along the propagation direction that is equivalent to a magnetic wall., This work was supported by the Ministerio de Economia, Industria, y Competitividad, Spanish government, under research projects TEC2013-47037-C5-3-R, TEC2013-47037-C5-1-R, TEC2016-75934-C4-1-R, and TEC2016-75934-C4-4-R and by Generalitat Valenciana under research project PROMETEOII/2015/005.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On Space Mapping Techniques for Microwave Filter Tuning

  • Melgarejo-Lermas, Juan Carlos
  • Ossorio-García, Javier
  • GUGLIELMI, MARCO
  • Bandler, John W.
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Space mapping (SM) and aggressive SM (ASM) techniques are widely used in the synthesis and design of microwave filters. Their popularity stems from the inherent simplicity of the procedures and from their effectiveness. The objective of this article is to extend the state of the art of these techniques by discussing how they can also be used very effectively to tune microwave filters. In addition to the theory, the successful tuning of a six-pole inductive waveguide filter is discussed in detail, thereby fully validating the proposed SM techniques., This work was supported by funds from the "La Caixa" Foundation (Code: B004442) and Agencia Estatal de Investigacion (AEI) and Union Europea through Fondo Europeo de Desarrollo Regional-FEDER-"Una manera de hacer Europa" (AEI/FEDER, UE), under Research Project TEC2016-75934-C4-1-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of Vibration Effects on Communication Filters in Substrate Integrated Technologies

  • Merello, José M.
  • Nova-Giménez, Vicente
  • Belenguer, Ángel
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Esteban González, Héctor|||0000-0002-5936-658X
[EN] The growing need of space communication systems forces the industry to innovate in order to provide more robust, economical and flexible solutions. The new substrate integrated technologies enable the development of on-board communications devices with less weight and volume than the traditional waveguide-based ones. However, it is necessary to analyse the performance of these devices in the particular working conditions of satellite communications. This work studies the integrity of the electrical response of advanced communication filters under mechanical stress conditions. Four realisations of a Ku-band microwave filter in different substrate integrated technologies were developed and tested. Two mechanical vibration tests were performed: sinusoidal sweep and random vibration. These tests emulate the transport and launching conditions of the satellite payload. Furthermore, the mechanical natural frequency of the filters and its variation after being exposed to the tests have been measured to evaluate the devices integrity. For all the filters, this frequency variation is lower than 5 %, the standard threshold. This proves that the developed filters can survive the launching conditions of satellite payload, thus qualifying the technology for spatial applications., This work was supported in part by the Generalitat Valenciana Research Project (PROMETEO/2019/120); in part by the Agencia Estatal de Investigacion, Spain, under the Fellowship for Training Ph.D.s (BES-2017-079728); in part by the Ministerio de Ciencia e Innovacion (MICIN), Spanish Government, under Research and Development Project PID2019-103982RB-C41 (funded by MICIN/AEI/10.13039/501100011033); and in part by the Conferencia de Rectores de las Universidades Espanolas (CRUE)-Universitat Politecnica de Valencia (by paying the open access charge).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

A Wideband Diplexer for Ka-Band Passive Intermodulation Measurement

  • Smacchia, D.
  • Carceller, C.
  • Guglielmi, M.
  • González-Santatecla, Pablo
  • Soto Pacheco, Pablo|||0000-0002-2734-620X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Ruiz-Garnica, Jesús|||0000-0002-2361-2806
In this paper we propose a novel Ka-band waveguide diplexer for passive intermodulation (PIM) measurements. Due to the higher operating frequency, this type of measurement setup usually requires wideband filters. In addition, due to the very large separation between satellite uplink and downlink bands, the PIM measurement diplexer unit must operate over a very wide frequency band. To satisfy such wide bandwidth requirements, the proposed topology is based on a band-reject filter for the downlink frequency band which is designed to provide, at the same time, the optimal passband performance for the downlink, and the optimal equiripple rejection over the PIM band. For the PIM channel, a band-pass filter combined with a high-pass section has been used. To validate the design, a prototype has been designed and manufactured. Very good agreement is shown between simulations and measurements, thereby fully validating the proposed solution.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Novel Magnetic Coupling for Miniaturized Bandpass Filters in Embedded Coaxial SIW

  • Sirci, Stefano
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, embedded coaxial substrate integrated waveguide (CSIW) filters with innovative magnetic couplings are presented and studied. By creating the loading capacitance of a combline topology using inner layers of a low-temperature co-fired ceramic (LTCC) stack-up, it is possible to achieve resonator miniaturization while improving the spurious-free band and providing full-packaged solutions. Moreover, a new magnetic coupling scheme consisting of short-ended stripline probes is proposed and analyzed in detail, both for direct and external couplings. An in-line three-pole filter at L-band is designed, manufactured, and measured proving how the proposed approach can be used for designing wideband bandpass filter (BPF) with extremely compact size. The designed BPF is centered at 1.5 GHz with 10% fractional bandwidth (FBW), while the layout size is just 35 x 9.5 mm(2). The experimental results validate the coaxial SIW technology that allows for, at the same time, easy integration, compact size, flexible design, and enhanced stop-band performance., This research was funded by Ministerio de Economia, Industria y Competitividad, Spanish Government, under Research Project TEC2016-75934-C4-3-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization of Nematic Liquid Crystals at Microwave Frequencies

  • Nova-Giménez, Vicente
  • Villacampa, Belén
  • Kronberger, Rainer
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The use of nematic liquid crystal (LC) mixtures for microwave frequency applications presents a fundamental drawback: many of these mixtures have not been properly characterized at these frequencies, and researchers do not have an a priori clear idea of which behavior they can expect. This work is focused on developing a new procedure for the extraction of the main parameters of a nematic liquid crystal: dielectric permittivity and loss tangent at 11 GHz under different polarization voltages; splay elastic constant K11, which allows calculation of the threshold voltage (Vth); and rotational viscosity ¿11, which allows calculating the response time of any arbitrary device. These properties will be calculated by using a resonator-based method, which is implemented with a new topology of substrate integrated transmission line. The LC molecules should be rotated (polarized) by applying an electric field in order to extract the characteristic parameters; thus, the transmission line needs to have two conductors and low electric losses in order to preserve the integrity of the measurements. This method was applied to a well-known liquid crystal mixture (GT3-23002 from MERCK) obtaining the permittivity and loss tangent versus bias voltage curves, the splay elastic constant, and the rotational viscosity of the mixture. The results validate the viability of the proposed method., This work was partially funded by the Generalitat Valenciana research project PROMETEO/2019/120, by Agencia Estatal de Investigacion (Spain) under the Fellowship for Training PhDs BES-2017-079728, by Ministerio de Ciencia e Innovacion, Spanish Government, under Project PID2019-103982RB-C41, and by Gobierno de Aragon (Ref.:E47_20R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Advanced Filtering Solutions in Coaxial SIW Technology Based on Singlets, Cascaded Singlets, and Doublets

  • Sirci, Stefano
  • Sánchez-Soriano, Miguel Ángel
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The use of singlets, cascaded singlets and doublets in coaxial substrate integrated waveguide (SIW) technology is proposed in this paper, with the aim of implementing low-loss filters with very compact size and highly-selective symmetric, asymmetric as well as dual-band responses. Singlets based on coaxial SIW resonator structures with source-load coupling are presented and studied. Then, different filter examples based on N cascaded singlets are designed, fabricated and measured at 7.5 GHz, with up to N transmission zeros (TZs) that can be easily located below and above the passband. Moreover, the application of doublets based on a dual-mode coaxial SIW resonator with source-load coupling for achieving extremely compact dual-band filters is presented, and two examples with different bandwidth configuration for each channel are designed, demonstrating the flexibility of the proposed coaxial SIW structure. The obtained experimental results of the different implemented filters show a good agreement with simulations, thus confirming the interesting potential application of these structures for the design of very compact devices with advanced filtering responses., This work was supported by the Ministerio de Economia, Industria y Competitividad, Spanish Government, under Project TEC2016-75934-C4-3-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evanescent-Mode Ridge-Waveguide Radiating Filters for Space Applications

  • Sánchez-Escuderos, Daniel
  • Tosso, Giovanni
  • Angeletti, P.
  • GUGLIELMI, MARCO
  • Ruiz-Garnica, Jesús|||0000-0002-2361-2806
  • Baquero Escudero, Mariano|||0000-0001-8772-5431
  • Soto Pacheco, Pablo|||0000-0002-2734-620X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper describes a new family of all-metallic radiators based on below-cutoff apertures fed by evanescentmode ridge waveguide filters. The pass band of the filters and the polarization of the apertures are configured to radiate orthogonal signals at different center frequencies. The simultaneous operation of these radiators in an array configuration results in interleaved apertures producing overlapped fields. This strategy reduces the volume and weight of the antenna system, which is a specially appealing characteristic in satellite antennas. Each isolated evanescent-mode filter ends in a small-size aperture and is designed following a novel synthesis procedure. Next, the radiating elements are combined, and the resulting array is analyzed as a multiplexer from the input ports to the freespace region thus accounting for all mutual couplings between different apertures. To validate the theoretical formulations, a prototype has also been manufactured. The results obtained show very good agreement between simulation and measurements in terms of reflection coefficient, side-lobe level and realized gain, thereby fully validating the new family of radiating arrays., This work was supported by the Spanish Ministry of Economics and Competitiveness under Project TEC2016-79700-C2-1-R, Project TEC2016-78028-C3-3-P, Project TEC2013-47037-C5-1-R, and Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A New Family of Multiband Waveguide Filters Based on a Folded Topology

  • Melgarejo, Juan Carlos
  • Guglielmi, Marco
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this article, we describe a new family of multiband waveguide filters based on a folded topology. The folded topology allows to use the filters of different orders and the introduction of transmission zeros. The design of the multiband filter is based on the aggressive space mapping (ASM) technique and is able to take into account manufacturing details, such as round corners and tuning elements. The filter structure is validated by designing, manufacturing, and measuring a triband filter. The agreement between simulations and measurements is shown to be excellent, thereby fully validating both the filter topology and the design process., This work was supported in part by the La Caixa Foundation under Grant B004442 and in part by the Agencia Estatal de Investigacion (AEI) and Union Europea through the Fondo Europeo de Desarrollo Regional (FEDER) "Una manera de hacer Europa" (AEI/FEDER, UE) under Research Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Novel Planar and Waveguide Implementations of Impedance Matching Networks Based on Tapered Lines Using Generalized Superellipses

  • Cogollos, Santiago|||0000-0002-4189-2952
  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
[EN] For the practical implementation of RF and microwave impedance matching networks, a widely employed solution¿alternative to the use of classical impedance transformers¿is based on tapered lines. This paper shows a simple method to design smooth tapers that take into account the dispersion of the line and the required design bandwidth simultaneously. A planar taper has been designed in microstrip technology with the same length of classical ones but improving their performances. A waveguide prototype has also been designed with similar performance to a commercial one but with one third of its length. Both tapered structures have been obtained through the optimization of very few parameters using the same design strategy. As a result, the reflection coefficient of the tapers can be optimally adapted to a given specific mask using the prescribed value of physical length. Experimental results for both tapers are included for the validation of the proposed topologies and the related design method., This work was supported by MINECO (Spanish Government) through R&D under Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Miniaturization of Power Divider and 90º Hybrid Directional Coupler for C-Band Applications Using Empty Substrate-Integrated Coaxial Lines

  • Merello-Gimenez, José Manuel
  • Nova-Giménez, Vicente
  • Belenguer Martínez, Ángel
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper presents the practical realization of a power divider and a 90° hybrid directional coupler in an empty substrate-integrated coaxial line (ESICL) for C-band frequency applications. This new type of transmission line is very promising in terms of electric performance, bandwidth, integration with other planar circuits, and manufacturing simplicity. The ESICL has been designed for obtaining a wide monomode bandwidth with a characteristic impedance of 50 . Furthermore, an improvement of the efficient transition between the ESICL and the grounded coplanar waveguide, used as feeding line, has been also proposed. The passive devices built using this technology are reduced in mass and volume, keeping robustness, and providing a well-balanced power division, as well as reduced losses and high isolation in the whole operational bandwidth. Two prototypes have been manufactured and the experimental results are in good agreement with the simulated designs., This work was supported in part by the Generalitat Valenciana Research under Project PROMETEOII/2015/005, in part by the Ministerio de Educacion, Cultura y Deporte, Spain, through the Fellowship Program for Training University Professors under Grant FPU14/00150, and in part by the Ministerio de Economia y Competitividad, Spain, through the Research and Development Projects under Grant TEC2016-75934-C4-1-R and Grant TEC2016-75934-C4-3-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fast Frequency Sweep Technique Based on Segmentation for the Acceleration of the Electromagnetic Analysis of Microwave Devices

  • Martínez-Zamora, Juan Ángel
  • BELENGUER MARTÍNEZ, ANGEL
  • Esteban González, Héctor|||0000-0002-5936-658X
[EN] The characterization of communication devices in a certain frequency band can be accelerated if a fast frequency sweep technique is used instead of a discrete frequency sweep. Existing fast frequency sweep techniques are either complex or specific for a certain electromagnetic solver. In this work, a new fast frequency sweep method is proposed that consists in segmenting the device under analysis into simple building blocks. Each building block is characterized with a generalized (multimode) circuital matrix whose elements present a simple and flat frequency response that is interpolated using natural cubic splines with very few points. In this way, the response of each block along the whole frequency band is obtained efficiently and accurately with as many frequency points as desired. Then, the circuital matrices of all the blocks are cascaded and the circuital matrix of the whole device in obtained. The new fast frequency sweep was successfully applied to the analysis of different types of devices (all metallic rectangular waveguide filter, dielectric loaded rectangular waveguide filter, and substrate integrated waveguide filter). The computational times were reduced to 15% or 19%, depending on the device, when compared with a discrete frequency sweep using the same electromagnetic solver., This research was funded by Ministerio de Economia, Industria y Competitividad, Spanish Government, under Research Projects TEC2016-75934-C4-3-R and TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Additive manufacturing and metallization of high-frequency communication devices

  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Marín García, Mª Luisa|||0000-0002-9789-8894
  • Nova-Giménez, Vicente
  • Ferrer, Álvaro
  • Martínez, Asunción
  • Sandoval, Nacho
  • Ponce-Gonzalez, Luis Nicolas
[EN] Additive manufacturing (AM) can be applied to new scenarios where traditional subtractive techniques limit geometry and assembling freedom. One of these scenarios is the development of high-frequency devices for communication systems, where AM offers the capability to develop high-complexity geometries, reducing the devices' weight and cost. This is extraordinarily convenient for recent small satellites where size, weight, and integration are vital. This work presents an AM process specially optimized to develop communication devices. Industry needs have been studied, and materials and manufacturing techniques have been chosen accordingly. Two communication devices, a band-pass filter and a horn antenna, have been developed using two VAT photopolymerization (VPP) processes and different resins. Printed devices were metallized using a two-step process based on a first electroless metallisation and a final galvanic plating. The manufactured pieces were sandblasted prior to metallization to increase plating adhesion and reduce surface roughness. Finally, several dimensional analyses were performed to evaluate the effect of finishing and plating on the manufacturing process using scanning electron microscopy, profilometry, and contact metrology. The electromagnetic response of developed devices is excellent and comparable with commercial devices manufactured with subtractive techniques. A preliminary tolerance analysis was carried out to approximate the systematic deviation of the overall manufacturing process, considering the erosion of sandblasting and the thickness of copper plating. These deviations were compensated in the design step to improve the dimensional accuracy of the band-pass filter., This work was supported by the Agencia Valenciana de la Innovación research project INNVA1/2020/84, by the Agencia Estatal de Investigación (Spain) under the Fellowship for Training PhDs BES-2017-079728, and by the Ministerio de Ciencia e Innovación (MICIN, Spanish Government) through the Research and Development projectPID2019-103982RB-C41 (under Grant MICIN/ AEI/10. 13039/501100011033). Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Highly Reliable and Repeatable Soldering Technique for Assembling Empty Substrate Integrated Waveguide Devices

  • Martinez, Juan A.
  • Belenguer, Angel
  • Esteban González, Héctor|||0000-0002-5936-658X
[EN] In this paper, a novel mymargin soldering technique that improves the fabrication process of empty substrate integrated waveguide (ESIW) devices is presented. Up until now, in order to fabricate an ESIW device, the tin solder paste was distributed, before assembling, on the contact surface between layers, in order to ensure a good electrical contact. This process has a low degree of repeatability (random soldering thickness and distribution of tin) and reliability (a significant number of nonworking prototypes due to tin overflow). In this paper, we propose the mechanization of a set of plated vias just next to the metalized walls of the ESIW in the central layer. Next, in the top and bottom covers that close this ESIW, additional plated vias are drilled in the same position so that, when the device is assembled (using screws or rivets), metalized holes can be seen passing through the whole structure from top to bottom. These holes are then used as soldering vias that can guide the tin paste straight to the point where it is needed. When the paste is dried, soldered vias ensure a very good electrical contact between layers. In addition, the fluid tin fills any small gap that appears between layers, thus providing a very good electrical contact and mechanical union. This novel soldering technique has been validated with experimental results. Several prototypes of filters centered at 13 and 35 GHz have been fabricated, proving the repeatability and reliability of the proposed soldering technique., This work was supported by the Ministerio de Economiy Competitividad, Spanish Government, under Project TEC2016-75934-C4-3-R and Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Systematic procedure for the efficient design of folded waveguide comb-line filters

  • San-Blas, A. A.
  • Pérez-Guijarro, J.
  • Guglielmi, M.
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] A systematic procedure for the efficient design of folded waveguide comb-line filters is presented. The proposed strategy is based on dividing the design process in more simple stages, in order to reduce the number of variables to be optimized in each step of the design process. The electrical response of an equivalent circuit model of the waveguide component considered in each step is used as a target response. Moreover, a method for obtaining an initial value for some key dimensions of the filter is also addressed. Finally, an S-band 6-pole folded comb-line filter has been successfully designed following the proposed design strategy.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Integration of a Very High Quality Factor Filter in Empty Substrate Integrated Waveguide at Q-band

  • Martínez-Zamora, Juan Ángel
  • de Dios, Juan J.
  • Belenguer Martínez, Ángel
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Recently, new methodologies for manufacturing empty waveguides completely integrated in a planar substrate have been proposed in order to improve the performance of substrate-integrated devices. One of these alternatives is the so-called empty substrate-integrated waveguide (ESIW). The height of high-frequency substrates, where ESIW devices are integrated, is very small. Then, the capacity of storing energy of ESIW resonators is drastically reduced, and as a result, their quality factor is not as high as it could be with a higher ESIW. In order to overcome this restriction, a novel integrated structure is proposed to embed very high-quality factor filters based on the ESIW with an increased height. As a result, we show, in this letter, for the first time, the successful integration of an increased-height ESIW filter in a printed circuit board of 0.305 mm height at Q-band, achieving a quality factor above 1000, which is a remarkable result for a completely substrate-integrated device operating in this frequency band. When compared with the same filter manufactured with an ESIW with the same height as the substrate, the novel filter shows a measured quality factor 85% higher., This work was supported by the Ministerio de Economia y Competitividad, Spanish Government, under Project TEC2016-75934-C4-3-R and Project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Novel spatial domain integral equation formulation for the analysis of rectangular waveguide steps close to arbitrarily shaped dielectric and/or conducting posts

  • Quesada Pereira, Fernando Daniel
  • Gomez Molina, Celia
  • Alvarez Melcon, Alejandro
  • Guglielmi, Marco
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] In this paper, a novel integral equation formulation expressed in the spatial domain is proposed for the analysis of rectangular waveguide step discontinuities. The important novelty of the proposed formulation is that which allows to easily take into account the electrical influence of a given number of arbitrarily shaped conducting and dielectric posts placed close to the waveguide discontinuity. For the sake of simplicity, and without loss of generality, the presented integral equation has been particularized and solved for inductive rectangular waveguide geometry. In this case, the integral equation mixed-potentials kernel is written in terms of parallel plate Green¿s functions with an additional ground plane located on the waveguide step. Therefore, the unknowns of the problem are reduced to an equivalent magnetic surface current on the step aperture and equivalent magnetic and electric surface currents on the dielectric and conducting posts close to the discontinuity. The numerical solution of the final integral equation is efficiently computed after the application of acceleration techniques for the slowly convergent series representing the Green¿s functions of the problem. The numerical method has been validated through several simulation examples of practical microwave devices, including compact size band-pass cavity filters and coupled dielectric resonators filters. The results have been compared to those provided by commercial full-wave electromagnetic simulation software packages, showing in all cases a very good agreement, and with substantially enhanced numerical efficiencies., This research work has been financially supported by the Spanish Ministerio de Economia y Competitividad in the frame of the projects "Demostradores Tecnologicos de Filtros y Multiplexores con Respuestas Selectivas y Sintonizables en Nuevas Guias Compactas para Aplicaciones Espaciales (COMPASSES)" with Ref. TEC2016-75934-C4-1-R, and "Analisis y Diseno de Nuevos Componentes en Microondas y Milimetricas para Comunicaciones por Satelite (MILISAT)" with Ref. TEC2016-75934-C4-4-R. As an additional financial source we thank the regional agency Fundacion Seneca from Region de Murcia under the research project "Desarrollo de Antenas y Componentes Pasivos de Microondas para Sistemas Avanzados de Comunicaciones" with Ref. 19494/PI/14 and Ref. 20147/EE/17, and the PhD scholarship granted by the Spanish national Ministerio de Educacion, Cultura y Deporte with Ref. FPU15/02883. All results of this paper can be reproduced by using the data and information contained in the drawings and in the captions of the figures included in the paper.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the Secondary Electron Yield in Dielectrics Using Equivalent Circuital Models

  • Bañón, David
  • Socuellamos, J. M.
  • Mata-Sanz, Rafael
  • Mercadé-Morales, Laura
  • Gimeno Martínez, Benito
  • Raboso García-Baquero, David
  • Semenov, V.
  • Rakova, E.I
  • Sánchez-Royo, J. F.
  • Segura García del Río, Alfredo
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Secondary electron emission has an important role on the triggering of the multipactor effect; therefore, its study and characterization are essential in radio-frequency waveguide applications. In this paper, we propose a theoretical model, based on equivalent circuit models, to properly understand charging and discharging processes that occur in dielectric samples under electron irradiation for secondary electron emission characterization. Experimental results obtained for Pt, Si, GaS, and Teflon samples are presented to verify the accuracy of the proposed model. Good agreement between theory and experiments has been found., The authors would like to thank the European High Power Space Materials Laboratory for its contribution-a laboratory funded by the European Regional Development Fund-a way of making Europe. Many thanks to the University of Valencia (Spain) for supporting this research activity with the internal program "Assistance for temporary stays of invited researchers within the framework of the Subprogramme Attraction of Talent 2015".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Implementation of Waveguide Terminations With Low-Passive Intermodulation for Conducted Test Beds in Backward Configuration

  • Smacchia, Davide
  • Guglielmi, Marco
  • Raboso, David
  • Soto Pacheco, Pablo|||0000-0002-2734-620X
  • Morro, J. V.|||0000-0002-4699-6208
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This letter proposes a simple procedure to implement low-passive intermodulation (PIM) terminations in waveguide technology to measure conducted backward PIM. The procedure consists in inserting a filter before the waveguide termination of the test bench. This approach reduces the PIM contribution from the load and, consequently, lowers the residual PIM noise floor of the test bench. To validate the procedure, a conducted backward low-PIM setup working in K-band has been assembled and tested. The PIM performance improvement obtained fully confirms the validity of the proposed solution., This work was supported in part by the European Space Agency through several research and development contracts, in part by the Ministerio de Economia y Competitividad (Spanish Government) under Project TEC2016-75934-C4-1-R, and in part by the ESA-VSC High Power RF Space Laboratory.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the Alignment of Low-Fidelity and High-Fidelity Simulation Spaces for the Design of Microwave Waveguide Filters

  • Ossorio-García, Javier
  • Melgarejo-Lermas, Juan Carlos
  • Guglielmi, Marco
  • Bandler, John
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The objective of this paper is to advance the state of the art of aggressive space mapping (ASM) by demonstrating how, for resonant structures, and microwave filters in particular, an ASM-based optimization procedure may converge to the desired target performance in just one step. This behavior is first justifed in physical terms, using the electromagnetic cavity perturbation theory, and is then investigated numerically. Several practical filter design demonstrations are also presented. This paper is concluded with a conceptual definition of Space Alignment in the context of ASM., This work was supported by MINECO (Spanish Government) under R&D Project TEC2016-75934-C4-1-R and R&D Technicians Grant PTA2015-10839-I.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Wideband Balanced Bandpass Filters With Very Broad Common-Mode and Differential-Mode Stopbands

  • Sans, Marc
  • Selga, Jordi
  • Vélez, París
  • Bonache, J.
  • Rodríguez Pérez, Ana María
  • Martin Antonlin, Ferran
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Compact balanced bandpass filters based on a combination of multisection mirrored stepped-impedance resonators and interdigital capacitors are presented in this paper. The considered filter topology is useful to achieve wide bandwidths for the differential mode, with broad stop bands for that mode, as well as very efficient common-mode suppression. By conveniently adjusting the transmission zeros for both operation modes, the differential- and common-mode stopbands can be extended up to significantly high frequencies. Filter size and this differential- and common-mode stopband performance are the main relevant characteristics of the proposed balanced filters. The potential of the approach is illustrated by the design of a prototype order-5 balanced bandpass filter, with central frequency $f_{0} = 1.8$ GHz, 48% fractional bandwidth (corresponding to 55.4% ¿3-dB bandwidth), and 0.04-dB ripple level. The filter is automatically synthesized by means of an aggressive space-mapping software tool, specifically developed, and two (pre- and post-) optimization algorithms, necessary to determine the transmission-zero frequencies. The designed filter is as small as $0.48lambda _{g} times 0.51lambda _{g}$ , where $lambda _{g}$ is the guided wavelength at the central filter frequency, and the differential-mode stopband extends up to at least 6.5 GHz with more than 22-dB rejection. The common-mode suppression is better than 28 dB from dc up to at least 6.5 GHz., This work was supported in part by MINECO-Spain under Project TEC2013-40600-R, Project TEC2016-75650-R, and Project TEC2016-75934-C4-1-R, in part by the Generalitat de Catalunya under Project 2014SGR-157, in part by the Institucio Catalana de Recerca i Estudis Avancats (who awarded F. Martin), and in part by by FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On Multimode Equivalent Network Representation of Finite Arrays of Open-Ended Waveguides

  • Sánchez-Escuderos, Daniel
  • Guglielmi, Marco
  • Baquero Escudero, Mariano|||0000-0001-8772-5431
  • Soto Pacheco, Pablo|||0000-0002-2734-620X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This communication describes a multimode equivalent network (MEN) representation of a finite array of open-ended lossless waveguides on an infinite ground plane. The derivation is based on an integral equation formulated at the interface between the waveguides and the free-space region. The MEN is formulated using the concept of accessible and localized modes, and includes ports for the free-space plane waves. The MEN derived can be easily combined with the MENs of other microwave components, thus allowing for the accurate analysis and design of more complex systems composed of waveguide elements and radiating apertures. Both simulated and experimental results are presented showing a very good agreement, thereby fully validating the proposed equivalent network representation., This work was supported in part by the Spanish Ministry of Economics and Competitiveness under Project TEC2013-47360-C3-3-P, Project TEC2016-79700-C2-1-R, Project TEC2016-78028-C3-3-P, Project TEC2013-47037-C5-1-R, and Project TEC2016-75934-C4-1-R and in part by the Generalitat Valenciana under Project GV/2015/065.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compact Wideband Hybrid Filters in Rectangular Waveguide With Enhanced Out-of-Band Response

  • Valencia-Sullca, Joaquín Francisco
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Guglielmi, Marco
[EN] This paper describes the design procedure of a compact wideband waveguide filter, based on stepped impedance resonators (SIR) and a combined usage of capacitive and inductive coupling irises, that provides a significant improvement in the out-of-band response of the filter with respect to the state-ofthe- art. In addition to theory, several filter prototypes have been designed and manufactured. A detailed sensitivity analysis has been also carried out. Finally, simulations and measurements are compared, showing very good agreement, thereby fully validating the new filter topology., This work was supported in part by the Ministerio de Economia y Empresa (MINECO) (Spanish Government) through the R&D Project under Grant TEC2016-75934-C4-1-R and in part by Generalitat Valenciana through Santiago Grisolia under Grant GRISOLIA/2017/073.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Design of Miniaturized Substrate Integrated Filters Using Aggressive Space Mapping

  • Martínez Pérez, Jorge Daniel|||0000-0002-7119-3714
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Sirci, Stefano
[EN] An optimization procedure for the design of miniaturized substrate integrated quasi-lumped filters based on aggressive space mapping techniques is presented in this paper. A gradient-descent approach based on a lossy coarse model is employed. Thus, a 3-pole bandpass filter response centered at 10 GHz is designed, manufactured and measured, showing the validity of the technique even if strong dependencies between the different electrical and physical parameters are present.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Reconfigurable Resonator in Decoupled Empty SIW Technology Using Liquid Crystal Material

  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Nova-Giménez, Vicente
[EN] This paper presents a novel continuously tunable microwave resonator based on Liquid Crystal (LC) material. The reconfigurable device is implemented in Decoupled Empty Substrate Integrated Waveguide (DESIW) technology. DESIW technology allows both magnetic and electric DC (or low frequency) biasing of the LC. The resonator is continuously tunable in a range of 600 MHz, resulting in a measured tunability range of 8.5% around a centre frequency of 7 GHz. Moreover, the measured insertion loss of the reconfigurable device is between 4.3 dB and 6.8 dB, thus obtaining a Q-factor of 190-172., This work was partially funded by the Generalitat Valenciana research project PROMETEOII/2015/005, by the Ministerio de Educación, Cultura y Deporte (Spain) under the Fellowship Program for Training University Professors FPU14/00150, and by Ministerio de Economía y Competitividad (Spain) under R&D project TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Versatile Transition for Multilayer Compact Devices in Empty Substrate Integrated Waveguide

  • Ballesteros, José A.
  • Fernández-Berlanga, Marcos D
  • Belenguer Martínez, Ángel
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Empty substrate integrated waveguide (ESIW) devices can provide high quality and completely integrated devices, but they are usually larger than the same ones imple- mented with alternative technologies. One of the most extended strategies to compact electronic devices is the use of multilayer technology. Nevertheless, to perform multilayer devices in ESIW, a versatile and efficient transition between the guides in different layers is needed. Currently, only one multilayer device is known in this ESIW technology, which is a transition between a pair of guides built in contiguous layers that requires complex and nonstandard 3-D manufacturing processes. In this letter, a multilayer transition to connect a pair of guides separated by an arbitrary number of layers is successfully designed and experimentally validated without 3-D manufacturing processes. This novel and versatile transition opens the way to further develop multilayer compact devices in the ESIW technology such as compact filters., This work was supported by the Ministerio de Economia y Competitividad through Spanish Government under Project TEC2016-75934-C4-3-R and Project TEC2016-75934-C4-1-R. (Corresponding author: Angel Belenguer.)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Advanced Compact Setups for Passive Intermodulation Measurements of Satellite Hardware

  • Smacchia, Davide
  • Guglielmi, Marco
  • Carceller Candau, Carlos
  • Ruiz-Garnica, Jesús
  • Galdeano, Jaione
  • Raboso García-Baquero, David
  • Soto Pacheco, Pablo|||0000-0002-2734-620X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper provides the guidelines for the practical development of novel advanced test beds for passive intermodulation(PIM) measurements. The proposed test beds show high performance and are flexible, allowing for the measurement of several PIM signals of different orders, with two or more input carriers. In contrast to classic test beds for satellite hardware, based on the cascaded connection of several elements, an integrated solution involving the minimum number of hardware pieces is proposed. The result is a lower number of flanged interconnections, thus reducing residual PIM level and insertion losses. In addition, return loss degradation and harmful spurious generation in the interconnections are also avoided. Measurement test beds for conducted and radiated PIM, in both transmitted and reflected directions, are discussed, highlighting the benefits and drawbacks of each configuration. Design guidelines for the key components are fully discussed. Illustrative application examples are also reported. Finally, excellent experimental results obtained from low-PIM measurement setups, working from C-band to Ka-band, are shown, thus fully confirming the validity of the proposed configurations., This work was supported in part by the European Space Agency through several research and development contracts, in part by the Ministerio de Economia y Competitividad (Spanish Government) under Project TEC2016-75934-C4-1-R, and in part by the ESA-VSC High Power RF Space Laboratory.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microwave Filter based on Substrate Integrated Waveguide with Alternating Dielectric Line Sections

  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Juliá Morte, María
  • Nova-Giménez, Vicente
[EN] A new topology of microwave filter based on sub- strate integrated waveguide (SIW) with alternating dielectric line sections is presented in this letter. The two alternating sections are waveguides without and with a dielectric material acting, respectively, as the inverters and the resonant sections of the pro- posed filter. This topology allows to easily design and manufacture compact filters with lower losses and higher rejection band than other available SIW realizations. For validation purposes, a prototype of a four-pole bandpass filter, based on alternating dielectric line sections, has been designed and manufactured, including successful experimental results., This work was supported in part by the Generalitat Valenciana Research Project under Grant PROMETEOII/2015/005, in part by the Ministerio de Educacion, Cultura y Deporte (Spain) through the Fellowship Program for Training University Professors under Grant FPU14/00150, and in part by the Ministerio de Economia y Competitividad (Spain) through the Research and Development Project under Grant TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermal Stability Analysis of Filters in Substrate Integrated Technologies under Atmospheric Pressure and Vacuum Conditions

  • Nova-Giménez, Vicente
  • Martínez, Juan Ángel
  • Merello, José Manuel
  • Belenguer Martínez, Ángel
  • Monerris, Óscar
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Substrate integrated (SI) technologies, either completely or partially filled with dielectric, as well as completely empty (i.e. without any dielectric material), have been object of intense research in the last years. Their performance in terms of losses, cost and size are mid-way between those of classical planar lines and rectangular waveguides. Many communication devices have already been successfully designed, manufactured and measured in all these SI technologies. But these measurements are mostly done at room temperature under atmospheric pressure conditions. However, the good results (in terms of low loss, profile and cost) of these novel technologies, especially the completely empty versions, close to the performance of the rectangular waveguide, make them a very good alternative for being used in small satellite payloads. Up to now, few attention has been given to the thermal analysis of these SI technologies, still missing a complete comparative study of these effects under both, atmospheric pressure and vacuum conditions. In this work the same filter is implemented on four different SI technologies (including completely and partially filled with dielectric, as well as empty -no dielectric- versions). The four filters are designed, manufactured, and measured at different temperatures according to the thermal testing standards for space applications. The thermal study is performed under atmospheric pressure conditions and, for the first time, under high vacuum conditions. Finally, a comparison with all previous available thermal studies (all of them performed at atmospheric pressure levels) is included., This work was supported in part by the Generalitat Valenciana Research Project PROMETEO/2019/120, in part by the Ministerio de Economía y Competitividad, Spain, through the Research and Development Project under Grant TEC2016-75934-C4-1-R, and in part by the Agencia Estatal de Investigación, Spain, through the Fellowship for Training PhDs under Grant BES-2017-079728.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Stop Band Continuous Profile Filter in Empty Substrate Integrated Coaxial Line

  • Gómez, Dario
  • Belenguer Martínez, Ángel
  • Lucas Borja, Alejandro
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Substrate integrated waveguides reduce the losses and increase the quality factor of resonators in communication filters when compared with traditional planar technologies, while maintaining their low-cost and low-profile characteristics. Empty substrate integrated waveguides go one step further, removing the dielectric of the substrate. One of these transmission lines is the empty substrate integrated coaxial line (ESICL), which has the advantage of being a two-conductor structure. Thus, it propagates a transversal electric and magnetic (TEM) mode, which reduces the dispersion and the bandwidth limitation of other one conductor empty substrate integrated waveguides. Continuous profile filters, at the cost of being long structures, are very easy to manufacture and design (usually no optimization is needed), and they are highly insensitive to manufacturing tolerances. In this work, a simple continuous profile filter, with a stop band response, is designed for the first time using novel ESICL technology. The influence of the design parameters on the insertion losses and fractional bandwidth is discussed. A prototype has been successfully manufactured and measured. A sensitivity analysis shows the high tolerance of the proposed stop band filter to manufacturing errors., This research was funded by Ministerio de Economia, Industria y Competitividad, Spanish Government, under Research Projects TEC2016-75934-C4-3-R and TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Stay tuned: A novel continuously-tunable reconfigurable microwave resonator based on Liquid Crystal materials

  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Nova-Giménez, Vicente
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Wideband Transition for Increased-Height Empty Substrate Integrated Waveguide

  • Martínez-Zamora, Juan Ángel
  • BELENGUER MARTÍNEZ, ANGEL
  • de Dios, Juan J.
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] Recently, Empty Substrate Integrated Waveguide (ESIW) technology was proposed for embedding empty waveguides into planar substrates in order to improve their performance. A low-loss and narrow-band transition from microstrip to an increased height ESIW with 4 layers was presented in a previous work, and used to implement a very high-quality factor bandpass filter at Q-band. With such a narrow-band transition, based on a quarter-wavelength transformer, a very narrow-band filter response with resonators having a quality factor of 1000 was achieved. In this paper, in order to overcome the narrow-band and the 4-layers output restrictions, and extend the practical use of such increased height ESIWs beyond narrow-band filters, we present a novel wideband transition from microstrip to an increased height ESIW with an arbitrary number of layers. A full suite of wideband transitions to increased height ESIWs, built with different number of substrate layers ranging from 3 to 8, has been designed in this work to operate at Ka-band, though they can be easily transferred to other bands if the dimensions of the transition are properly scaled. To illustrate this, the original Ka-band transitions have been mapped to Ku-band, with excellent results. In order to test the proposed design method, a prototype of a 4-layer structure has been fabricated at Ka-band, achieving a good performance in the whole useful bandwidth of the ESIW., This work was supported in part by the Ministerio de Economia y Competitividad, Spanish Government, under Project TEC2016-75934-C4-3-R and Project TEC2016-75934-C4-1-R, and in part by the Consejeria de Educacion, Cultura y Deportes, Autonomous Government of Castilla-La Mancha, under Project SBPLY/17/180501/000351.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

New Decoupled Empty Substrate Integrated Waveguide Realization

  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Esteban González, Héctor|||0000-0002-5936-658X
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Belenguer Martínez, Ángel
  • Nova-Giménez, Vicente
[EN] This work presents a novel Decoupled Empty Substrate Integrated Waveguide (DESIW), which enables AC/DC decoupling in any device that is integrated in it. The decoupling strategy is performed throughout a micro-milling square pattern of easy implementation that increases the insertion losses compared to the standard ESIW. However, the DESIW related losses are still tolerable, allowing the employment of the new periodic structure in many practical applications. In particular, it can be used for the design and manufacturing of reconfigurable devices which need a bias voltage on the whole device, or just on some of its particular areas. A broadband transition from DESIW to microstrip planar lines has been also successfully designed. The new line has been manufactured and measured., This work was partially founded by the Generalitat Valenciana research project PROMETEOII/2015/005, by the Ministerio de Educacion, Cultura y Deporte (Spain) under the Fellowship Program for Training University Professors FPU14/00150 and by Ministerio de Economia y Competitividad (Spain) under R&D project TEC2016-75934-C4-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization of Nematic Liquid Crystal at Microwave Frequencies Using Split-Cylinder Resonator Method

  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Nova-Giménez, Vicente
  • Villacampa, Belén
  • de la Rua, Alberto
  • Kronberger, Rainer
[EN] Liquid crystal (LC) is an anisotropic liquid material, which flows like a liquid, but at the same time, its molecules have an orientational order like in the solid state. Thus, LC is a promising dielectric material for designing reconfigurable devices at microwave frequencies. In order to optimize the design of reconfigurable microwave devices, accurate values of the dielectric permittivity and the loss tangent of LCs are needed. However, new LCs are not well characterized at these frequencies because of its recent use for microwave applications. Therefore, the characterization in this frequency range is required for its practical use within microwave components and devices. In this paper, a split-cylinder resonator method is used for the characterization of four different nematic LCs at two frequency points, i. e., 5 and 11 GHz. This characterization includes the extraction of their complex dielectric permittivity values at these frequencies. The employed method allows to obtain the two extreme permittivity values without applying any external electric or magnetic field to polarize the LC molecules. Two different approaches, a modal analysis method and a full-wave numerical technique, have been used for determining the LC parameters obtaining similar results in both cases., This work was supported in part by the Generalitat Valenciana Research under Project PROMETEOII/2015/005, in part by the Ministerio de Educacion, Cultura y Deporte, Spain, through the Fellowship Program for Training University Professors under Grant FPU14/00150, in part by the Ministerio de Economia y Competitividad, Spain through Research and Development Projects under Grant TEC2016-75934-C4-R-1, and in part by the Gobierno de Aragon-Fondo Europeo de Desarrollo Regional (FEDER)-Fondo Social Europeo 2017-2019 under Reference E14-7R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Exploring the Tuning Range of Channel Filters for Satellite Applications Using Electromagnetic-Based Computer Aided Design Tools

  • Ossorio-García, Javier
  • Guglielmi, Marco
  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] The objective of this paper is to use electromagnetic-based computer-aided design (CAD) tools to investigate the maximum tuning range of channel filters, typically used in satellite payloads. Both circular and rectangular waveguide technologies are investigated. The results of the investigation show that single-mode rectangular waveguide implementations offer substantially wider tuning range, as opposed to classical dual-mode circular waveguide implementations. In addition to simulations, measurements are also presented indicating very good agreement with theory, thereby fully validating the CAD procedure., This work was supported in part by MINECO (Spanish Government) under Research and Development Project TEC2016-75934-C4-1-R and in part by Research and Development Technicians under Grant PTA2015-10839-I.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Controlled Out-of-Band Rejection of Filters based on SIW with Alternating Dielectric Line Sections

  • Sánchez-Marín, Juan Rafael|||0000-0003-4887-5810
  • Bachiller Martin, Maria Carmen|||0000-0002-5518-5060
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Nova-Giménez, Vicente
[EN] A study for managing the out-of-band rejection in a new topology of filters based on substrate integrated waveguide with alternating dielectric line sections (ADLSs) is presented in this letter. ADLS is a filtering structure consisting on line sections of the same width but with alternating air and dielectric filling. The design of the lengths of each section provides the central frequency and the bandwidth of bandpass filter response. The proper selection of the structure substrate dielectric permittivity can increase the rejection band up to 2 f(o). Moreover, the selection of the filter order (i.e., the number of sections with and without dielectric) can affect the depth of the rejection band. A study of the width and the depth of the rejection band is performed with different permittivities and orders for two different filters. Then, for validation purposes, the prototypes of both filters have been manufactured and measured., This work was supported in part by the Generalitat Valenciana Research Project under Grant PROMETEOII/2015/005, in part by the Ministerio de Educacion, Cultura y Deporte, Spain, through the Fellowship Program for Training University Professors under Grant FPU14/00150, and in part by the Ministerio de Economia y Competitividad, Spain, through Research and Development Project under Grant TEC2016-75934-C4-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Multipactor Effect Characterization of Dielectric Materials for Space Applications

  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Taroncher Calduch, Mariam|||0000-0001-9068-1169
  • Melgarejo-Lermas, Juan Carlos
  • Guglielmi, Marco
  • Anza Hormigo, Sergio
  • Vicente Quiles, Carlos Pascual
  • Moreno Cambroreno, María del Rocío
  • Gimeno Martínez, Benito
  • Raboso García-Baquero, David
[EN] The objective of this paper is to advance the state of the art in the characterization of the multipactor effect in dielectric materials. The materials studied are the most commonly used dielectrics in space applications, namely, Alumina, Rexolite, Rogers RT5870, Rohacell, Teflon, and Ultem 1000. In this paper, a new family of coaxial waveguide components, covering the L- and S-bands, with a wideband, low-pass response has been designed, and six different prototypes have been specifically optimized and manufactured. The six prototypes have then been used to simulate and measure the multipactor breakdown susceptibility charts for the six dielectric materials investigated. Finally, the simulation results are compared with the results of the measurement campaign indicating good agreement., This work was supported in part by the European Space Agency through Research Project "Novel Investigation in Multipactor Effect in Ferrite and Other Dielectrics Used in High Power RF Space Hardware" under Grant AO 1-7551/13/NL/GLC and in part by MINECO (Spanish Government) through Research and Development Project under Grant TEC2016-75934-C4-1-R. This paper is an expanded version from the IEEE MTT-S International Microwave Workshop Series on Advanced Materials and Processes IMWS-AMP 2017, Pavia, Italy, September 20-22, 2017.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Optimized Design of Combline Filters with Transmission Zeros

  • Vague Cardona, José Joaquín|||0000-0001-5935-3116
  • Cogollos, Santiago|||0000-0002-4189-2952
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
  • Ossorio García, Javier
  • Guglielmi, Marco
[EN] The objective of this paper is to demonstrate how inline combline filters can be designed to implement transmission zeros in the filter transfer function. Following the design procedure described in this paper, up to N-1 transmission zeros can be implemented with a filter of order N. In addition to theory, comparisons between simulated and measured results are also presented. The agreement between simulation and measurements is indeed good, thereby fully validating the new combline filter topology, and the proposed design technique.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Signal-Interference-Based Structure with Negative Group Delay Properties

  • Sánchez-Soriano, Miguel Ángel
  • Durá, Javier
  • Sirci, Stefano
  • Marini, Stephan
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
In this work, a signal-interference-based structure with negative group delay (NGD) properties is proposed. The proposed topology allows an easy control and design of the NGD characteristics, such as the group delay GD at the design frequency, the NGD bandwidth (NBW) and the maximum attenuation. For that purpose, some design closed-form expressions have been analytically obtained and design curves have been provided. The circuit sensibility as a function of the design parameters is also studied. In order to demonstrate the capabilities of the proposed structure, a proof-of-concept circuit has been designed and implemented to be centered at 1 GHz. It has shown a very broad NBW of 320 MHz, with a NGD of −0.8 ns at 1 GHz and a maximum attenuation of 15 dB.
RUA. Repositorio Institucional de la Universidad de Alicante
Publication Otros (Other)

Cover-Ended Resonators to Increase Corona Discharge Thresholds in Microstrip Bandpass Filters

  • Morales-Hernández, Aitor
  • Sánchez-Soriano, Miguel Ángel
  • Marini, Stephan
  • Boria Esbert, Vicente Enrique
  • Guglielmi, Marco
  • Marini, Stephan|||/items/f9c8c8d4-d768-49bf-aae8-bb53041bd8b4
  • Sánchez-Soriano, Miguel Ángel|||/items/b47af293-b2ab-4567-88b8-66decd71861b
In this work, corona discharge breakdown thresholds in microstrip bandpass filters are studied. If a gas is subjected to strong electric fields, gas breakdown may occur with severe consequences for microwave devices. The objective of this paper is to propose a solution for the mentioned problem for a microstrip bandpass filter, through the implementation of dielectric material covers over the open-circuit terminations of the resonators forming the filter, where the voltage magnification is maximum. A parametric study of covers' dimensions for an open-ended resonator is presented, and it is analyzed how the maximum electric field strength and the unloaded quality factor are affected. Finally, the aforementioned study is applied to the design of a fifth-order bandpass filter with hairpin resonator configuration centered at 1.6 GHz. Numerical results show that by using this strategy, the peak power handling capability (PPHC) of microstrip filters can be considerably enhanced without hardly degrading the filter response performance.
Repositorio Digital UPCT
Publication Artículo científico (JournalArticle)

Design and implementation of evanescent mode waveguide filters using dielectrics and additive manufacturing techniques

  • Pons Abenza, Alejandro
  • García Barceló, José María
  • Romera Pérez, Antonio
  • Melcón Álvarez, Alejandro
  • Quesada Pereira, Fernando Daniel
  • Hinojosa Jiménez, Juan
  • Guglielmi, Marco
  • Boria Esbert, Vicente Enrique
  • Arche Andradas, Lara
In this contribution, we describe the design of bandpass filters using evanescent mode waveguides and dielectric resonators implemented with additive manufacturing techniques. Two C-band Chebyshev evanescent mode waveguide filters of order five have been designed using a low cost commercial dielectric material (ABSplus), widely used by Fused Deposition Modeling (FDM) 3D printers. The housings of the filters have been manufactured using traditional computer numerical control (CNC) machining techniques. Practical manufacturing considerations are also discussed, including the integration of dielectric and metallic parts. We first discuss two breadboards using two different resonator geometries. We then demonstrate how different transfer functions can be easily implemented by changing the 3D printed parts in the same metallic housing. Breadboards show fractional bandwidths between 3% and 4.6% with return losses better than RL ¼ 18 dB, and spurious free ranges of SFR ¼ 1 GHz. Insertion losses are better than IL ¼ 4:3 dB. Even though dielectric losses from the plastic material are shown to be high, the measured results are quite satisfactory, thereby clearly showing that this strategy maybe useful for the fast production of low cost microwave filters implementing complex geometries., This work has been developed with funding from Thales Alenia Space (Tres Cantos, Madrid, Spain) and has also been financially supported by the Spanish Ministerio de Economía y Competitividad in the frame of the projects Ref. TEC2016-75934-C4-1-R, Ref. TEC2016-75934-C4-4-R and Ref. FPA2016-76978-C3-2-P.