Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 41
Encontrada(s) 1 página(s)

IRTA Pubpro. Open Digital Archive
Publication Artículo científico (JournalArticle)

Compact analytical flow system for the simultaneous determination of L-lactic and L-malic in red wines

  • Giménez-Gómez, Pablo
  • Gutiérrez-Capitán, Manuel
  • Capdevila, Fina
  • Puig-Pujol, Anna
  • Jiménez-Jorquera, Cecilia
  • Fernández-Sánchez, César
During the malolactic fermentation of red wines, L-malic acid is mainly converted to L-lactic acid. Both acids should be precisely measured during the entire process to guarantee the quality of the final wine, thus making real-time monitoring approaches of great importance in the winemaking industry. Traditional analytical methods based on laboratory procedures are currently applied and cannot be deployed on-site. In this work, we report on the design and development of a bi-parametric compact analytical flow system integrating two electrochemical biosensors that could be potentially applied in this scenario. The developed flow-system will allow for the first time the simultaneous measurement of both acids in real scenarios at the real-time and in remote way. Miniaturized thin-film platinum four-electrode chips are fabricated on silicon substrates by standard photolithographic techniques and further implemented in a polymeric fluidic structure. This includes a 15 µL flow cell together with the required fluidic channels for sample and reagent fluid management. The four-electrode chip includes counter and pseudo-reference electrodes together with two working electrodes. These are sequentially modified with electropolymerized polypyrrole membranes that entrap the specific receptors for selectively detecting both target analytes. The analytical performance of both biosensors is studied by chronoamperometry, showing a linear range from 5 × 10−6 to 1 × 10−4 M (LOD of 3.2 ± 0.3 × 10−6 M) and from 1 × 10−7 to 1 × 10−6 M (LOD of 6.7 ± 0.2 × 10−8 M) for the L-lactate and the L-malate, respectively. Both biosensors show long-term stability, retaining more than the 90% of their initial sensitivity after more than 30 days, this being a prerequisite for monitoring the whole process of the malolactic fermentation of the red wines (time between 20 and 40 days). The flow system performance is assessed with several wine samples collected during the malolactic fermentation process of three red wines, showing an excellent agreement with the results obtained with the standard method., info:eu-repo/semantics/publishedVersion
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Compact analytical flow system for the simultaneous determination of L-lactic and L-malic in red wines

  • Giménez-Gómez, Pablo
  • Gutiérrez-Capitán, Manuel
  • Capdevila, Fina
  • Puig-Pujol, Anna
  • Jiménez-Jorquera, Cecilia
  • Fernández Sánchez, César
During the malolactic fermentation of red wines, L-malic acid is mainly converted to L-lactic acid. Both acids should be precisely measured during the entire process to guarantee the quality of the final wine, thus making real-time monitoring approaches of great importance in the winemaking industry. Traditional analytical methods based on laboratory procedures are currently applied and cannot be deployed on-site. In this work, we report on the design and development of a bi-parametric compact analytical flow system integrating two electrochemical biosensors that could be potentially applied in this scenario. The developed flow-system will allow for the first time the simultaneous measurement of both acids in real scenarios at the real-time and in remote way. Miniaturized thin-film platinum four-electrode chips are fabricated on silicon substrates by standard photolithographic techniques and further implemented in a polymeric fluidic structure. This includes a 15 µL flow cell together with the required fluidic channels for sample and reagent fluid management. The four-electrode chip includes counter and pseudo-reference electrodes together with two working electrodes. These are sequentially modified with electropolymerized polypyrrole membranes that entrap the specific receptors for selectively detecting both target analytes. The analytical performance of both biosensors is studied by chronoamperometry, showing a linear range from 5 × 10-6 to 1 × 10-4 M (LOD of 3.2 ± 0.3 × 10-6 M) and from 1 × 10-7 to 1 × 10-6 M (LOD of 6.7 ± 0.2 × 10-8 M) for the L-lactate and the L-malate, respectively. Both biosensors show long-term stability, retaining more than the 90% of their initial sensitivity after more than 30 days, this being a prerequisite for monitoring the whole process of the malolactic fermentation of the red wines (time between 20 and 40 days). The flow system performance is assessed with several wine samples collected during the malolactic fermentation process of three red wines, showing an excellent agreement with the results obtained with the standard method., Funding text 1 We acknowledge the group of Dr. Iluminada Gallardo (Chemistry Department, Universitat Autònoma de Barcelona, Spain) for kindly helping us with the polypyrrole distillation process. This work used the Spanish ICTS Network MICRONANOFABS and was partly supported by the Spanish Ministry of Economy, Industry and Competitiveness. Funding text 2 P.G.-G. carried out the optimization and the validation of the bi-parametric compact analytical flow system with wine samples. F.C. and A.P.-P. carried out the wine samples selection and collection, as well as the analytical measurements with standard enzymatic methods. P.G.-G., M.G.-C., C.F.-S. and C.J.-J. managed and coordinated the execution of the research activity. All the authors prepared the draft. P.G.-G. and C.F.-S revised and edited the manuscript. C.J.-J. and C.F.-S. obtained the financial support to carry out the projects associated with the manuscript., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Compact analytical flow system for the simultaneous determination of L-lactic and L-malic in red wines

  • Giménez-Gómez, Pablo
  • Gutiérrez-Capitán, Manuel
  • Capdevila, Fina
  • Puig-Pujol, Anna
  • Jiménez-Jorquera, Cecilia
  • Fernández-Sánchez, César
During the malolactic fermentation of red wines, L-malic acid is mainly converted to L-lactic acid. Both acids should be precisely measured during the entire process to guarantee the quality of the final wine, thus making real-time monitoring approaches of great importance in the winemaking industry. Traditional analytical methods based on laboratory procedures are currently applied and cannot be deployed on-site. In this work, we report on the design and development of a bi-parametric compact analytical flow system integrating two electrochemical biosensors that could be potentially applied in this scenario. The developed flow-system will allow for the first time the simultaneous measurement of both acids in real scenarios at the real-time and in remote way. Miniaturized thin-film platinum four-electrode chips are fabricated on silicon substrates by standard photolithographic techniques and further implemented in a polymeric fluidic structure. This includes a 15 µL flow cell together with the required fluidic channels for sample and reagent fluid management. The four-electrode chip includes counter and pseudo-reference electrodes together with two working electrodes. These are sequentially modified with electropolymerized polypyrrole membranes that entrap the specific receptors for selectively detecting both target analytes. The analytical performance of both biosensors is studied by chronoamperometry, showing a linear range from 5 × 10−6 to 1 × 10−4 M (LOD of 3.2 ± 0.3 × 10−6 M) and from 1 × 10−7 to 1 × 10−6 M (LOD of 6.7 ± 0.2 × 10−8 M) for the L-lactate and the L-malate, respectively. Both biosensors show long-term stability, retaining more than the 90% of their initial sensitivity after more than 30 days, this being a prerequisite for monitoring the whole process of the malolactic fermentation of the red wines (time between 20 and 40 days). The flow system performance is assessed with several wine samples collected during the malolactic fermentation process of three red wines, showing an excellent agreement with the results obtained with the standard method., info:eu-repo/semantics/publishedVersion
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Lossy mode resonance sensors based on lateral light incidence in nanocoated planar waveguides

  • Fuentes Lorenzo, Omar
  • Del Villar, Ignacio
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
The deposition of an indium oxide (In2O3) thin film on conventional planar waveguides (a coverslip and a glass slide) allows generating lossy mode resonances (LMR) by lateral incidence of light on the waveguide and by registering the optical spectrum in a spectrometer. This novel sensing system becomes an alternative to optical fibre, the substrate where LMR-based sensors have been developed so far, since it is easier to handle and more robust. An additional advantage is that cost effective waveguides, such as slides or coverslips, can be used in a platform that resembles surface plasmon resonance-based sensors in the Kretschmann configuration but without the need for a coupling prism and with the advantage of being able to generate TE and TM LMR resonances with metallic oxide or polymer thin films. The results are corroborated with simulations, which provide in-depth understanding of the phenomena involved in the sensing system. As a proof-of-concept for the optical platform, two refractometers were developed, one with low sensitivity and for a wide range of refractive indices, and the other with higher sensitivity but for a narrower refractive index range. The sensors presented here open up the path for the development of LMR-based chemical sensors, environmental sensors, biosensors, or even the generation of other optical phenomena with the deposition of multilayer structures, gratings or nanostructures, which is much easier in a planar waveguide than in an optical fibre., The authors would like to acknowledge the partial support to the Spanish Ministry of Economy and Competitiveness TEC2016-78047-R and TEC2016-79367-C2-2-R research funds, the pre-doctoral research grant and the Government of Navarre 2018/PC021-022 OPTISENS research funds.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Hg2+ optical fiber sensor based on LSPR generated by gold nanoparticles embedded in LBL nano-assembled coatings

  • Martínez Hernández, María Elena
  • Goicoechea Fernández, Javier
  • Arregui San Martín, Francisco Javier
Mercury is an important contaminant since it is accumulated in the body of living beings, and very small concentrations are very dangerous in the long term. This paper reports the fabrication of a highly sensitive fiber optic sensor using the layer-by-layer nano-assembly technique with gold nanoparticles (AuNPs). The gold nanoparticles were obtained via a water-based synthesis route that use poly acrylic acid (PAA) as stabilizing agent, in the presence of a borane dimethylamine complex (DMAB) as reducing agent, giving PAA-capped AuNPs. The sensing mechanism is based on the alteration of the Localized Surface Plasmon Resonances (LSPR) generated by AuNPs thanks to the strong chemical affinity of metallic mercury towards gold, which lead to amalgam alloys., This work was supported in part by the Spanish Agencia Estatal de Investigación (AEI) and the European Regional Development Fund (ERDF) under the Project TEC2016-79367-C2-2-R, and Public University of Navarra pre-doctoral research grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Partially coated long period fiber Bragg gratings in multicore optical fibers

  • Barrera, David
  • Goicoechea Fernández, Javier
  • Madrigal, Javier
  • González Larequi, Marta
  • Arregui San Martín, Francisco Javier
  • Sales, Salvador
Multicore optical fibers (MCFs) have attracted considerable interest in the last years due to their potential in many applications including broadband communications, microwave photonics, and optical sensing [1,2]. In optical sensing, MCFs has been used in the past for implementing curvature and shape sensors [3]. However, the potential of MCFs for optical sensing is not limited to mechanical sensors and they can be used for implementing other types of sensors. In this paper, we investigate the use of MCFs for external refractive index (RI) sensing. We use LPGs inscribed in the cores of the fiber to detect changes in the external refractive index. Partially coating the surface of the optical fiber we can modify the sensitivity of the cores., This work was supported by the Ministry of Economy and Competitiveness under the projects DIMENSION TEC2017-88029-R and TEC2016-79367-C2-2-R (AEI/FEDER), the support of FINESSE the European Union¿s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie Action grant agreement n° 722509, and the support of the Generalitat Valenciana under the grant APOSTD/2016/015.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Fluorescent sensors for the detection of heavy metal ions in aqueous media

  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
  • Corres Sanz, Jesús María
  • Arregui San Martín, Francisco Javier
Due to the risks that water contamination implies for human health and environmental protection, monitoring the quality of water is a major concern of the present era. Therefore, in recent years several efforts have been dedicated to the development of fast, sensitive, and selective sensors for the detection of heavy metal ions. In particular, fluorescent sensors have gained in popularity due to their interesting features, such as high specificity, sensitivity, and reversibility. Thus, this review is devoted to the recent advances in fluorescent sensors for the monitoring of these contaminants, and special focus is placed on those devices based on fluorescent aptasensors, quantum dots, and organic dyes., This work was supported by the Spanish State Research Agency (AEI) and the Spanish Ministry of Economy and Competitiveness through the TEC2016-79367-C2-2-R project. Nerea de Acha would also like to acknowledge her pre-doctoral fellowship (reference BES-2014-069692) funded by the Spanish Ministry of Economy and Competitiveness through the TEC2013-43679-R project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Enhancement of the sensitivity of a volatile organic compounds MOF sensor by means of its structure

  • López Torres, Diego
  • López Aldaba, Aitor
  • Elosúa Aguado, César
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
  • Arregui San Martín, Francisco Javier
In this paper, we experimentally compare several core structures of Microstructured Optical Fibers (MOFs) for low-finesse Fabry-Pérot (FP) sensors. These sensors are designed for Volatile Organic Compounds (VOCs) measurements. We deposit Indium Tin Oxide (ITO) thin films by sputtering on the MOFs and different optical phase responses of the FP were measured for saturated atmospheres of ethanol. The sensitivity of the developed sensors is demonstrated to depend on the geometry and the dimensions of the MOF-cores. The sensors show recovery times under 100 s and the baselines are fully recovered after exposure to VOC., This work was supported by the research grant TEC2016-79367-C2-2-R and TEC 2016-76021-C2-1-R (AEI/FEDER, UE) as well as Public University of Navarre program PhD grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Microstructured optical fiber sensor for soil moisture measurements

  • López Aldaba, Aitor
  • López Torres, Diego
  • Campo-Bescós, Miguel
  • López Rodríguez, José Javier
  • Yerro Lizarazu, David
  • Elosúa Aguado, César
  • Arregui San Martín, Francisco Javier
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
Trabajo presentado a la 26th International Conference on Optical Fiber Sensors. Suiza, 2019, A discrete sensor based on a Sn0₂-FP (Fabry-Pérot) cavity is presented and characterized in real soil conditions. Results are compared, for the first time to our knowledge, with a commercial capacitive sensor and gravimetric measurements., The Spanish Government projects TEC 2016-76021-C2-1-R, TEC2016-78047-R, TEC2016-79367-C2-2-R, Innocampus and the Cost Action MP 1401, as well as to the AEI/FEDER Funds are acknowledged.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Sensitivity enhancement experimental demonstration using a low cutoff wavelength SMS modified structure coated with a pH sensitive film

  • Rodríguez Rodríguez, Wenceslao Eduardo
  • Del Villar, Ignacio
  • Ruiz Zamarreño, Carlos
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
  • Rodríguez Rodríguez, Adolfo Josué
  • Domínguez Cruz, René
The multimode interference (MMI) effect in a single mode-multimode-single mode (SMS) can be used fordevelopment of wavelength shift detection based sensors. In this work, the focus is centered on obtainingwavelength shifts with low cutoff single mode fibers, which allows exploring the wavelength range from600 to 1000 nm, where optical sources and detectors are less expensive than at longer wavelengths. Inaddition, the application of a reduction in the fiber diameter of the SMS structure by means of HF etching,combined with the deposition of a thin-film, enables to enhance the sensitivity of the devices at thesame time the objective mentioned before is achieved. In this sense, the effect of the deposition of a pHsensitive thin-film on SMS structures with different diameters allowed attaining a maximum sensitivityof 15 nm per pH unit in the range from pH 4 to pH 6, which improves by a factor of 3 the sensitivity ofSMS sensors without etching operating at longer wavelengths., This work was supported by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-79367-C2-2-R, TEC2016-78047-R), Government of Navarra PI044 NANOSEN, Government of Navarra PC023-024 BIPOTSENS research grants and the Direction of Internationalization and Academic Collaboration of the Autonomous University of Tamaulipas.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Sensores de fibra óptica basados en películas delgadas con nanopartículas metálicas, Optical fiber sensors based on thin films with metallic nanoparticles

  • Martínez Hernández, María Elena
El estudio del nanoensamblado de nanopartículas metálicas sobre fibra ópticaha contribuido al desarrollo de sensores con mayor sensibilidad y eficiencia. Las aplicaciones que se pueden obtener en este campo pueden variar en función de ciertos parámetros como el tipo de nanopartícula metálica, ruta de síntesis, set-up o técnica de nanoensamblado. Esta tesis se centra en la síntesis de nanopartículas metálicas de oro (AuNPs) y plata (AgNPs) y su posterior nanoensamblado en películas delgadas usando las técnicas Layer-by-Layer Embedding (LbL-E) y el proceso de In-Situ Synthesis (ISS), para el desarrollo de sensores de fibra óptica. Este trabajo se encuentra dividido en tres bloques,el primero se centra en el uso de la técnica LbL-E para el desarrollo de sensores plasmónicos de fibra óptica para la detección de parámetros químicos. En segundo lugar, la técnica ISS se ha utilizado como alternativa parala fabricación de un nuevo dispositivo sensor de humedad basado en una cavidad interferométrica de Fabry-Perot en puntade una fibra óptica. Por último, se compara los efectos sobre la sensibilidad de los Tilted Fiber Bragg Grating (TFBG) al índice de refracción externo al utilizar ambas técnicas (ISS y LbL-E) para el nanoensamblaje de AuNPs., The study of the nanoassembly of metallic nanoparticles on optical fiber has contributed to the development of sensors with greater sensitivity and efficiency. The applications that can be obtained in this field may vary depending on certain parameters such as the type of metallic nanoparticle, synthesis route, set-up or nanoassembly technique. This thesis focuses on the synthesis of metallic gold (AuNPs) and silver (AgNPs) nanoparticles and their subsequent nanoassembly in thin films using Layer-by-Layer Embedding (LbL-E) technique and the In-Situ synthesis (ISS) process, for the development of fiber optic sensors. This work is divided into three blocks. The first focuses on using the LbL-E technique to develop fiber optic plasmonic sensors for the detection of chemical parameters. Secondly, the ISS technique has been used as an alternative for fabricating a new humidity sensor device based on a Fabry-Perot interferometric cavity at the end of an optical fiber. Finally, the effects on the sensitivity of Tilted Fiber Bragg Gratings to the external refractive index when using both techniques (ISS and LbL-E) for the nanoassembly of AuNPs are compared., The development of this work has been possible thanks to the Public University of Navarre (UPNA) and by the sponsoring of the Spanish Agencia Estatal de Investigación (AEI) and the European Regional Development Fund (ERDF) under the Projects TEC2016-79367-C2-2-R and PID2019-106070RB-I00., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Luminescence-based optical sensors fabricated by means of the layer-by-layer nano-assembly technique

  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
  • Matías Maestro, Ignacio
  • Arregui San Martín, Francisco Javier
Luminescence-based sensing applications range from agriculture to biology, including medicine and environmental care, which indicates the importance of this technique as a detection tool. Luminescent optical sensors are required to be highly stable, sensitive, and selective, three crucial features that can be achieved by fabricating them by means of the layer-by-layer nano-assembly technique. This method permits us to tailor the sensors0 properties at the nanometer scale, avoiding luminophore aggregation and, hence, self-quenching, promoting the diffusion of the target analytes, and building a barrier against the undesired molecules. These characteristics give rise to the fabrication of custom-made sensors for each particular application., This work was supported by the Spanish State Research Agency (AEI) through the TEC2016- 79367-C2-2-R project and the European Regional Development Fund (ERDF-FEDER). Nerea de Acha would also like to acknowledge her pre-doctoral fellowship (reference BES-2014-069692) funded by the Spanish Ministry of Economy and Competitiveness through the TEC2013-43679-R project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Micro and nanostructured materials for the development of optical fibre sensors

  • Elosúa Aguado, César
  • Arregui San Martín, Francisco Javier
  • Del Villar, Ignacio
  • Ruiz Zamarreño, Carlos
  • Corres Sanz, Jesús María
  • Bariáin Aisa, Cándido
  • Goicoechea Fernández, Javier
  • Hernáez Sáenz de Zaitigui, Miguel
  • Rivero Fuente, Pedro J.
  • Socorro Leránoz, Abián Bentor
  • Urrutia Azcona, Aitor
  • Sánchez Zábal, Pedro
  • Zubiate Orzanco, Pablo
  • López Torres, Diego
  • Acha Morrás, Nerea de
  • Ascorbe Muruzabal, Joaquín
  • Ozcariz Celaya, Aritz
  • Matías Maestro, Ignacio
The measurement of chemical and biomedical parameters can take advantage of the features exclusively offered by optical fibre: passive nature, electromagnetic immunity and chemical stability are some of the most relevant ones. The small dimensions of the fibre generally require that the sensing material be loaded into a supporting matrix whose morphology is adjusted at a nanometric scale. Thanks to the advances in nanotechnology new deposition methods have been developed: they allow reagents from different chemical nature to be embedded into films with a thickness always below a few microns that also show a relevant aspect ratio to ensure a high transduction interface. This review reveals some of the main techniques that are currently been employed to develop this kind of sensors, describing in detail both the resulting supporting matrices as well as the sensing materials used. The main objective is to offer a general view of the state of the art to expose the main challenges and chances that this technology is facing currently., This work was supported by the Spanish State Research Agency (AEI) and European Regional Development Fund (ERDF-FEDER), TEC2016-79367-C2-2-R and TEC2016-78047-R projects.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Fabrication of long period gratings by periodically removing the coating of cladding-etched single mode optical fiber towards optical fiber sensor development

  • Ascorbe Muruzabal, Joaquín
  • Corres Sanz, Jesús María
  • Del Villar, Ignacio
  • Matías Maestro, Ignacio
Here, we present a novel method to fabricate long period gratings using standard single mode optical fibers (SMF). These optical devices were fabricated in a three-step process, which consisted of etching the SMF, then coating it with a thin-film and, the final step, which involved removing sections of the coating periodically by laser ablation. Tin dioxide was chosen as the material for this study and it was sputtered using a pulsed DC sputtering system. Theoretical simulations were performed in order to select the appropriate parameters for the experiments. The responses of two different devices to different external refractive indices was studied, and the maximum sensitivity obtained was 6430 nm/RIU for external refractive indices ranging from 1.37 to 1.39., This work was supported by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-78047-R and TEC2016-79367-C2-2-R), and by the Government of Navarre through the project with reference 2017/PI044.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Optical fiber vacuum sensor based on etched SMS structure and PDMS coating

  • Ascorbe Muruzabal, Joaquín
  • Fuentes Lorenzo, Omar
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
  • Corres Sanz, Jesús María
In this work, an optical fiber vacuum sensor based on a single-mode multimode single-mode (SMS) structure coated with polydimethylsiloxane (PDMS) is studied. The SMS structure generates an interferometric pattern based on multimode interference. The structure is dip-coated with a layer of PDMS, whose optical properties change when it is subjected to varying vacuum pressure. Different strategies are applied in an attempt to improve the final performance of the sensor, such as decreasing the diameter of the fiber and modifying the properties of the coating by modifying the proportion of solvent. Decreasing the diameter of the optical fiber and using toluene as a solvent are both proved to be successful strategies for increasing the sensitivity of the sensor. The devices are studied in the 1×10-3–10 mbar range with a maximum wavelength shift of 12 nm, leading to a maximum sensitivity of 35 nm/mbar. The simplicity of the fabrication process, which can be applied to more sensitive structures, suggests that PDMS may be a good choice for the development of optical fiber vacuum sensors., This work was supported by the Spanish Agencia Estatal de Investigación (AEI), Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-79367-C2-2-R) and a Torres-Quevedo grant from the Science and Innovation Ministry (PTQ2018-010221).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Real time measuring system of multiple chemical parameters using microstructured optical fibers based sensors

  • López Aldaba, Aitor
  • López Torres, Diego
  • Elosúa Aguado, César
  • Arregui San Martín, Francisco Javier
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
In this paper, a multiplexing system for simultaneous interrogation of optical fiber sensors which measure different parameters is presented and validated. The whole system has been tested with 6 different sensing heads with different purposes: one temperature sensing head, two relative humidity sensors and three VOCs leak sensors; all of them based on microstructured optical fibers. The interrogation system uses the FFT technique to isolate each sensor's interference, enabling their simultaneous interrogation. The system interrogates all the sensors at frequencies up to 1 KHz, showing a good performance of each measurement without crosstalk between sensors. The developed system is independent of the sensors' purpose or of the multiplexing topology., This work was supported in part by the Spanish Comisión Interministerial de Ciencia y Tecnología within projects under Grant TEC2016-76021-C2-1-R, Grant TEC2016-78047-R, and Grant TEC2016-79367-C2-2-R, in part by the Cost Action MP1401, and in part by the FEDER funds from the European Union.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Contribution to the development of optical fibre sensors based on microstructured optical fibres to detect gases and volatile organic compounds, Contribución al desarrollo de sensores de fibra óptica basados en fibras micro estructuradas para la detección de gases y compuestos orgánicos volátiles

  • López Torres, Diego
Desde la primera publicación relacionada con las fibras micro estructuradas (MOFs), el desarrollo de sensores basados en fibra óptica (OFSs), que utilizan este tipo de fibras, se ha visto incrementado atrayendo el interés de numerosos grupos de investigación debido al importante papel que juegan en numerosas aplicaciones. Debido a sus propiedades y estructuras únicas, las MOFs son muy útiles en aplicaciones ópticas de sensado, especialmente de gases y compuestos orgánicos volátiles (VOCs). Por estas razones, esta tesis doctoral propone la utilización de este tipo de fibras para generar y desarrollar nuevas estructuras y montajes, capaces de detectar estos parámetros, gases y VOCs. Además, se han realizado diferentes estudios y se han utilizado diferentes técnicas (destacando la transformada rápida de Fourier (FFT) y la multiplexación WDM…), para mejorar las características de los sensores, intentando conseguir de esta manera que el sistema final fuera lo más competitivo posible., Since the first publications related to Microstructured Optical Fibres (MOFs), the development of Optical Fibre Sensors (OFSs), based on this type of fibres, has been increased attracting the interest of many research groups because of the important role that they play in diverse applications. Due to their unique geometric structures and features, MOFs are very useful for optical sensing applications, especially gases and Volatile Organic Compounds (VOC) sensing. Taking it into account, this PhD. work proposes the utilization of MOFs to carry out and to develop new structures and set-ups capable to detect these parameters, gases and VOCs. Moreover, different studies and techniques, such as Fast Fourier Transform (FFT) or WDM multiplexing, have been used with the aim of improving the features of the sensors trying to make the final system as competitive as possible., La realización de este trabajo ha sido posible gracias a las aportaciones económicas recibidas por parte de la Universidad Pública de Navarra (UPNA), así como del patrocinio de la UPNA y del Ministerio de Economía y Competitividad, a través de los proyectos CICYT fondos TEC2013-43679-R, TEC2016-79367-C2-2-R. Este trabajo fue posible también gracias a los proyectos concedidos por el Gobierno de Navarra, con referencia 2016/PI012 EXCELSEN y a la financiación otorgada por la Fundación CAN a través de los proyectos CAN2015-70221 y BINACS: Bio Inspired Nanocoatings for Cellular Scaffolds., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Is there a frontier in sensitivity with lossy mode resonance (LMR) based refractometers?

  • Ozcariz Celaya, Aritz
  • Ruiz Zamarreño, Carlos
  • Zubiate Orzanco, Pablo
  • Arregui San Martín, Francisco Javier
A tin dioxide thin layer has been studied in order to improve the sensitivity of lossy mode resonances (LMR) based sensors. The effects of the thin film thickness and the polarization of light in a SnO2 coated D-shaped single mode optical fiber have been evaluated. The optimization of such parameters in the fabrication of refractometers have led to an unprecedented sensitivity of over one million nanometers per refractive index unit (RIU), which means a sensitivity below 10^(−9) RIU with a pm resolution detector. This achievement is a milestone for the development of new high sensitivity devices and opens the door to new industrial applications, such as gear oil degradation, or biomedical devices where previous devices could not provide enough sensitivity., The authors would like to acknowledge the partial support to the Spanish Ministry of Economy and Competitiveness TEC2016-79367-C2-2-R research funds, the Spanish Ministry of Education FPU15/05663 predoctoral research grant, the Public University of Navarre (UPNA) pre-doctoral research grant and Government of Navarre 2016/PC026 BIOPTSENS and 64/2015 research funds.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Optical fiber sensors based on microstructured optical fibers to detect gases and volatile organic compounds: a review

  • López Torres, Diego
  • Elosúa Aguado, César
  • Arregui San Martín, Francisco Javier
Since the first publications related to microstructured optical fibers (MOFs), the development of optical fiber sensors (OFS) based on them has attracted the interest of many research groups because of the market niches that can take advantage of their specific features. Due to their unique structure based on a certain distribution of air holes, MOFs are especially useful for sensing applications: on one hand, the increased coupling of guided modes into the cladding or the holes enhances significantly the interaction with sensing films deposited there; on the other hand, MOF air holes enhance the direct interaction between the light and the analytes that get into in these cavities. Consequently, the sensitivity when detecting liquids, gasses or volatile organic compounds (VOCs) is significantly improved. This paper is focused on the reported sensors that have been developed with MOFs which are applied to detection of gases and VOCs, highlighting the advantages that this type of fiber offers., This work was carried out with the financial support of MINECO (Spain) through TEC2016-79367-C2-2-R (AEI/FEDER, UE) as well as Public University of Navarre PhD grants program., This work was carried out with the financial support of MINECO (Spain) through TEC2016-79367-C2-2-R (AEI/FEDER, UE).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Sensitivity enhancement in low cutoff wavelength long-period fiber gratings by cladding diameter reduction

  • Del Villar, Ignacio
  • Partridge, Matthew
  • Rodríguez Rodríguez, Wenceslao Eduardo
  • Fuentes Lorenzo, Omar
  • Socorro Leránoz, Abián Bentor
  • Díaz Lucas, Silvia
  • Corres Sanz, Jesús María
  • James, Stephen
  • Tatam, Ralph
The diameter of long-period fiber gratings (LPFGs) fabricated in optical fibers with a low cutoff wavelength was be reduced by hydrofluoric acid etching, enhancing the sensitivity to refractive index by more than a factor of 3, to 2611 nm/refractive index unit in the range from 1.333 to 1.4278. The grating period selected for the LPFGs allowed access to the dispersion turning point at wavelengths close to the visible range of the optical spectrum, where optical equipment is less expensive. As an example of an application, a pH sensor based on the deposition of a polymeric coating was analyzed in two situations: with an LPFG without diameter reduction and with an LPFG with diameter reduction. Again, a sensitivity increase of a factor of near 3 was obtained, demonstrating the ability of this method to enhance the sensitivity of thin-film-coated LPFG chemical sensors., This work was supported by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-79367-C2-2-R, TEC2016-78047-R), by the Government of Navarre through the project with reference 2017/PI044 and with funding from the Engineering and Physical Sciences Research Council (EPSRC) UK, EP/L010437/1.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Femtomolar detection by nanocoated fiber label-free biosensors

  • Chiavaioli, Francesco
  • Zubiate Orzanco, Pablo
  • Del Villar, Ignacio
  • Ruiz Zamarreño, Carlos
  • Giannetti, Ambra
  • Tombelli, Sara
  • Trono, Cosimo
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
  • Baldini, Francesco
The advent of optical fibre-based biosensors combined with that of nanotechnologies has provided an oppor-tunity for developing in situ, portable, lightweight, versatile and high-performance optical sensing platforms. We report on the generation of lossy mode resonances by the deposition of nm-thick metal oxide films on optical fibres, which makes it possible to measure precisely and accurately the changes in optical properties of the fibre-surrounding medium with very high sensitivity compared to other technology platforms, such as long period gratings or surface plasmon resonances, the gold standard in label-free and real-time biomolecular interaction analysis. This property, combined with the application of specialty structures such as D-shaped fibres, permits enhancing the light-matter interaction. SEM and TEM imaging together with X-EDS tool have been utilised to characterise the two films used, i.e. indium tin oxide and tin dioxide. More-over, the experimental transmission spectra obtained after the deposition of the nanocoatings have been numerically cor-roborated by means of wave propagation methods. With the use of a conventional wavelength interrogation system and ad-hoc developed microfluidics, the shift of the lossy mode resonance can be reliably recorded in response to very low analyte concentrations. Repeated experiments confirm a big leap in performance thanks to the capability to detect femtomolar concentrations in human serum, improving the detection limit by three orders of magnitude when compared with other fibre-based configurations. The biosensor has been regenerated several times by injecting sodium dodecyl sul-phate, which proves the capability of sensor to be reused., This work was supported by the European Community for theproject Hemospec (FP7-611682), by the National ResearchCouncil of Italy (CNR) for the Short Term Mobility program2017, by the Government of Navarra (project no. 72/2015)and by the Spanish Agencia Estatal de Investigación (AEI) andEuropean Regional Development Fund (FEDER) (TEC2016-78047-R, TEC2016-79367-C2-2-R).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Layer-by-layer nano-assembly: a powerful tool for optical fiber sensing applications

  • Rivero Fuente, Pedro J.
  • Goicoechea Fernández, Javier
  • Arregui San Martín, Francisco Javier
The ability to tune the composition of nanostructured thin films is a hot topic for the design of functional coatings with advanced properties for sensing applications. The control of the structure at the nanoscale level enables an improvement of intrinsic properties (optical, chemical or physical) in comparison with the traditional bulk materials. In this sense, among all the known nanofabrication techniques, the layer-by-layer (LbL) nano-assembly method is a flexible, easily-scalable and versatile approach which makes possible precise control of the coating thickness, composition and structure. The development of sensitive nanocoatings has shown an exceptional growth in optical fiber sensing applications due to their self-assembling ability with oppositely charged components in order to obtain a multilayer structure. This nanoassembly technique is a powerful tool for the incorporation of a wide variety of species (polyelectrolytes, metal/metal oxide nanoparticles, hybrid particles, luminescent materials, dyes or biomolecules) in the resultant multilayer structure for the design of high-performance optical fiber sensors. In this work we present a review of applications related to optical fiber sensors based on advanced LbL coatings in two related research areas of great interest for the scientific community, namely chemical sensing (pH, gases and volatile organic compounds detection) as well as biological/biochemical sensing (proteins, immunoglobulins, antibodies or DNA detection)., This work was supported by the Spanish State Research Agency (AEI) and European Regional Development Fund (ERDF-FEDER), TEC2016-79367-C2-2-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Lossy mode resonances generated in planar configuration for two-parameter sensing

  • Fuentes Lorenzo, Omar
  • Corres Sanz, Jesús María
  • Domínguez Rodríguez, Ismel
  • Del Villar, Ignacio
  • Matías Maestro, Ignacio
This work shows a new sensor structure for simultaneous measurement of two parameters, temperature and refractive index. The optical configuration consists of incidence of light on the edge of a soda-lime coverslip fully coated with a CuO thin film and partially coated with a PDMS thick layer. This planar configuration permitted to generate two separated lossy mode resonances (LMRs): one centered at 600 nm and the other at 1000 nm. The second resonance is induced by the PDMS layer and it can be used to measure the temperature due to its high thermo-optic coefficient (the sensitivity is -1.75 nm/°C in the temperature range from 20 to 40 °C), whereas the first resonance is used for sensing refractive index with sensitivity of 1460 nm/RIU in the refractive index range from 1.3328 and 1.37. Finally, a calibration test was carried out using a calibrated oil series with refractive index ranging from 1.33 to 1.36. This work demonstrates the possibility of generating multiples resonances in a single structure as simple as a coverslip, which can be used as a multi-parameter interchangeable sensor, especially suitable for biological applications or the detection of heavy metals in water., This work was supported by Spanish Agencia Estatal de Investigación (AEI). Fondo Europeo de Desarrollo Regional (FEDER) TEC2016-79367-C2-2-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

SnO2-MOF-Fabry-Perot optical sensor for relative humidity measurements

  • López Aldaba, Aitor
  • López Torres, Diego
  • Elosúa Aguado, César
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • Arregui San Martín, Francisco Javier
  • López-Amo Sáinz, Manuel
In this paper, a new optical fiber sensor for relative humidity measurements is presented and characterized. The sensor is based on a SnO2 sputtering deposition on a microstructured optical fiber (MOF) low-finesse Fabry-Pérot (FP) sensing head. The feasibility of the device as a breathing sensor is also experimentally demonstrated. The interrogation of the sensing head is carried out by monitoring the Fast Fourier Transform phase variations of the FP interference frequency. This method substitutes the necessity of tracking the optical spectrum peaks or valleys, which can be a handicap when noise or multiple contributions are present: therefore, it is low-sensitive to noise and to artifacts signal amplitude. The sensor shows a linear behavior in a wide relative humidity range (20%–90% relative humidity) in which the sensitivity is 0.14 rad/%; the maximum observed instability is 0.007 rad, whereas the highest hysteresis is 5% RH. The cross correlation with temperature is also considered and a method to lower its influence is proposed. For human breathing measurement, the registered rising and recovery times are 370 ms and 380 ms respectively., The authors are grateful to A. Ortigosa, D. Erro, Dr. M. Bravo and Dr. R.A. Perez-Herrera. We also thank the Spanish Government projects TEC2013-47264-C2-2-R, TEC 2016-76021-C2-1-R, TEC2016-78047-R, TEC2016-79367-C2-2-R, Innocampus and the Cost Action MP 1401, as well as to the AEI/FEDER Funds.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Lossy mode resonance optical sensors based on indium-gallium-zinc oxide thin film

  • Ozcariz Celaya, Aritz
  • Dominik, Magdalena
  • Smietana, Mateusz
  • Ruiz Zamarreño, Carlos
  • Del Villar, Ignacio
  • Arregui San Martín, Francisco Javier
This work discusses an application of electrically conductive and optically transparent indium-gallium-zinc oxide (IGZO) thin films for fabrication of lossy mode resonance (LMR) based optical fiber refractometers. The films have been deposited on both 200 μm in diameter multimode fused silica fiber and D-shaped fiber structure. A sensitivity of 12,929 nm/RIU was obtained in the refractive index range between 1.39 and 1.42. In case of D-shaped fiber structure the effect of polishing depth on the LMR phenomenon has also been studied., This work was supported in part by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-79367-C2-2-R, TEC2016-78047-R), as well as by the Spanish Ministry of Education (FPU15/05663 grant) and the Government of Navarra 2016/PI044 NANOSEN, 0C023/024 BIOPTSENS and 64/2015 research funds. Support from National Science Centre, Poland within grant No. 2014/14/E/ST7/00104 is also acknowledged.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Peculiarities of the structural and optical properties of rare-earth-doped phosphate glasses for temperature sensing applications

  • Elisa, M.
  • Iordache, S.M.
  • Iordache, A.M.
  • Vasiliu, Ileana Cristina
  • Grigorescu, C.E.A.
  • Sava, Bogdan Alexandru
  • Boroica, L.
  • Filip, A.V.
  • Dinca, M. C.
  • Bartha, Cristina
  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
Eu, Er, Yb-Er, and Dy-doped phosphate glasses were prepared by a wet-route processing of chemical precursors followed by melt-quenching and annealing. XRD measurements highlighted the amorphous nature of the investigated glasses. UV-Vis absorption spectra revealed peaks specific to f-f electronic transitions of the doping ions whereas FTIR and Raman spectroscopy proved the vitreous network forming role of phosphorous pentoxide. Luminescence spectra in the Vis domain, at RT, showed emission bands characteristic to the ion transitions from the excited states to the ground state. The luminescence spectra collected in the 25-160°C range exhibited a decrease of the emission intensity with temperature rise. In the case of Eu and Dy-doped glasses a relatively small decrease of the emission intensity with temperature is observed by comparison with Er and, respectively, Yb-Er-doped glass where a significant change of the emission intensity is noticed, which recommends the latter as promising candidate for sensing devices., This work was supported by UEFISCDI (Executive Unity for Financing of Higher Education, Research and Innovation), Core Program, contracts no. 16N/2019, 18N/2019, and 21N/2019, project PN-III-P1-1.2-PCCDI-2017-0871/contract 47PCCDI/2018, project PN-III-P1-1.2-PCCDI-2017-0619/contract 42PCCDI/2018, by the Ministry of Research and Innovation through Program I - Development of the National R & D System, Subprogram 1.2 - Institutional Performance - Projects for Excellence Financing in RDI, contract no.19PFE/2018, and by Spanish State Research Agency and Spanish Ministry of Economy and Competitiveness through the project TEC2016-79367-C2-2-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Title enhancement of the sensitivity of a volatile organic compounds MOF-sensor by means of its structure

  • López Torres, Diego
  • López Aldaba, Aitor
  • Elosúa Aguado, César
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
  • Arregui San Martín, Francisco Javier
Trabajo presentado en la Eurosensors 2017 Conference. París, 3–6 de septiembre de 2017., In this paper, we experimentally compare several core structures of Microstructured Optical Fibers (MOFs) for low-finesse Fabry-Pérot (FP) sensors. These sensors are designed for Volatile Organic Compounds (VOCs) measurements. We deposit Indium Tin Oxide (ITO) thin films by sputtering on the MOFs and different optical phase responses of the FP were measured for saturated atmospheres of ethanol. The sensitivity of the developed sensors is demonstrated to depend on the geometry and the dimensions of the MOF-cores. The sensors show recovery times under 100 s and the baselines are fully recovered after exposure to VOC., This work was supported by the research grant TEC2016-79367-C2-2-R and TEC 2016-76021-C2-1-R (AEI/FEDER, UE) as well as Public University of Navarre program PhD grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Generation of lossy mode resonances in planar waveguides toward development of humidity sensors

  • Fuentes Lorenzo, Omar
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
  • Del Villar, Ignacio
Lossy mode resonances (LMRs) are typically obtained with optical fibre. The Kretschmann configuration is an alternative but LMRs are generated with angles approaching grazing incidence. In this work, a new setup is explored, based on the lateral incidence of light on conventional planar waveguides such as glass slides or coverslips. Indium tin oxide was deposited onto both types of waveguides generating LMRs. The results of the simulations carried out agree well with the experimental results. As an example of the potential of this new and simple optical configuration, a humidity sensor with a sensitivity of 0.212 nm/% relative humidity (RH) in the range from 65% to 90% of RH was developed, which expedites the development of other types of sensors already explored with LMR-based optical fibre sensors., This work was supported in part by the Spanish Agencia Estatal de Investigacion (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) under Project TEC2016-78047-R and Project TEC2016-79367-C2-2-R and in part by Pinar del Rio University.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Lossy mode resonance enabling ultra-low detection limit for fibre-optic biosensors (INVITED)

  • Chiavaioli, Francesco
  • Giannetti, Ambra
  • Tombelli, Sara
  • Trono, Cosimo
  • Del Villar, Ignacio
  • Matías Maestro, Ignacio
  • Zubiate Orzanco, Pablo
  • Ruiz Zamarreño, Carlos
  • Arregui San Martín, Francisco Javier
  • Baldini, Francesco
The combination of optical fibre-based biosensors with nanotechnologies is providing the opportunity for the development of in situ, portable, lightweight, versatile and high-sensitivity optical sensing platforms. We report on the generation of lossy mode resonances (LMRs) by means of the deposition of nm-thick SnO2 film on optical fibres. This allows measuring precisely and accurately the changes in refractive index of the fibre-surrounding medium with very high sensitivity compared to other optical technology platforms, such as long period grating or surface plasmon resonance. This approach, mixed with the use of specialty fiber structures such as Dshaped fibres, allows improving the light-matter interaction in strong way. Different imaging systems, i.e. SEM and TEM along with X-EDS tool, have been used to study the optical features of the fiber coating. The shift of the LMR has been monitored in real-time thanks to conventional wavelength interrogation system and ad hoc developed microfluidics. A big leap in performance has been attained by detecting femtomolar concentrations in human serum. The biosensor reusability has been also tested by using a solution of sodium dodecyl sulphate., This work was supported by the National Research Council of Italy (CNR) for the Short Term Mobility program 2017, by the Government of Navarra (project no. 72/2015) and by the Spanish Agencia Estatal de Investigacion (AEI) and European Regional Development Fund (FEDER) (TEC2016-78047-R,TEC2016-79367-C2-2-R).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Optical fiber vacuum sensor based on modal interferometer and PDMS coating

  • Ascorbe Muruzabal, Joaquín
  • Fuentes Lorenzo, Omar
  • Corres Sanz, Jesús María
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
Trabajo presentado a la 18th IEEE Sensors Conference. Montreal, 2019, This work studies the behavior of polydimethylsiloxane (PDMS) as a transducer for optical vacuum pressure measurements. The optical structure chosen for this device is a modal interferometer achieved by splicing a coreless multimode optical fiber between two single mode fibers. Then, an etching process is applied to the obtained device, in order to decrease the diameter of the fiber and increase the sensitivity. Finally, the fiber is coated by dip-coating with a layer of PDMS, which changes its volume with pressure changes. The device has been studied in the 1x10(-3) mbar to 10 mbar range with a wavelength shift of 4 nm. A maximum sensitivity of 35 nm/mbar was obtained. The simple fabrication process, which can be applied to more sensitive structures, suggest that PDMS can be a good choice for the development of optical fiber vacuum sensors., This work was supported by Spanish Agencia Estatal de Investigacion (AEI). Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-79367-C2-2-R and TEC2016-78047-R).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Comparison between capacitive and microstructured optical fiber soil moisture sensors

  • López Aldaba, Aitor
  • López Torres, Diego
  • Campo-Bescós, Miguel
  • López Rodríguez, José Javier
  • Yerro Lizarazu, David
  • Elosúa Aguado, César
  • Arregui San Martín, Francisco Javier
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
Soil moisture content has always been an important parameter to control because it is a deterministic factor for site-specific irrigation, seeding, transplanting, and compaction detection. In this work, a discrete sensor that is based on a SnO2–FP (Fabry-Pérot) cavity is presented and characterized in real soil conditions. As far as authors know, it is the first time that a microstructured optical fiber is used for real soil moisture measurements. Its performance is compared with a commercial capacitive soil moisture sensor in two different soil scenarios for two weeks. The optical sensor shows a great agreement with capacitive sensor’s response and gravimetric measurements, as well as a fast and reversible response; moreover, the interrogation technique allows for several sensors to be potentially multiplexed, which offers the possibility of local measurements instead of volumetric: it constitutes a great tool for real soil moisture monitoring., This work was supported by the Spanish Government projects TEC2016-76021-C2-1-R, TEC2016-78047-R, TEC2016-79367-C2-2-R, Innocampus and the Cost Action MP 1401, as well as to the AEI/FEDER Funds.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Aluminum doped zinc oxide (AZO) coated optical fiber LMR refractometers. An experimental demonstration

  • Ozcariz Celaya, Aritz
  • Piña-Azamar, Dafne A.
  • Ruiz Zamarreño, Carlos
  • Domínguez Cruz, René
  • Arregui San Martín, Francisco Javier
This work presents the experimental demonstration of lossy mode resonance generation by means of aluminum doped zinc oxide thin-films. The use of such material may allow to optimize the performance of LMR-based sensors, obtaining good sensitivity at lower costs than other overlays, such as those including indium. The refractometric response of the fabricated devices is explored in different spectral regions. One refractometer working in the near infrared region was fabricated, obtaining a sensitivity of 2280 nm/RIU. A second refractometer working in the visible light spectrum was also fabricated. This second device allows to observe rough refractive index variations with the naked eye as a change of the color of the light propagating through the fiber, simplifying the setup needed for its use., This work was partly supported by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (TEC2016-79367-C2-2-R, TEC2016-78047-R ). The authors would also like to thanks the Spanish Ministry of Education (FPU15/05663 grant) and the Government of Navarra 0C023/024 BIOPTSENS and 64/2015 research funds. Dafne A. Piña-Azamar thanks CONACYT for scholarship assigned and PFCE-UAT 2016 project for the financial support to carry out this work.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Dual-cavity fiber fabry-perot interferometer coated with SnO2for relative humidity and temperature sensing

  • Domínguez Flores, Carmen E.
  • Rodríguez-Quiroz, Osvaldo
  • Monzón-Hernández, David
  • Ascorbe Muruzabal, Joaquín
  • Corres Sanz, Jesús María
  • Arregui San Martín, Francisco Javier
An optical fiber tip interferometer for the measurement of relative humidity (RH) and temperature is proposed. The optical fiber structure used, a dual-cavity optical fiber Fabry-Perot interferometer (DFFPI), is simply-to-fabricate, compact, and robust. The reflectance (RDFFPI) of the interferometer is sensitive to the refractive index (RI) and temperature of the external medium. Consequently, when the cross-section of the fiber tip was coated with a SnO 2 thin film, whose RI changes according to the humidity of the surrounding ambient, the measurement of the RH was possible. An increment of the RH produced a decrement of RI of the SnO 2 thin film, then the reflectance of the fiber tip end-face diminished, and this produced a decrement of the visibility of the interference fringes. The analysis of the RDFFPI was carried out in the Fourier domain, using a novel processing method it was possible to establish that the amplitude of two peaks of Fourier spectrum changed at a ratio of 39.49 × 10 -3 %RH -1 in the range of 40 to 90 RH%. On the other hand, the temperature of the humidity chamber was monitored, from 25 to 60 °C at a fixed RH%, by analyzing the phase shift of the interference pattern produced by the changes in the optical path length of the cavities. The good sensitivity, stability, reproducibility, and compactness of the fiber tip RH sensor make this proposal very appealing in a wide range of applications., This work was supported in part by the Consejo Nacional de Ciencia y Tecnología (CONACyT) from Mexico through the CIENCIA BÁSICA under Project 257046 and Project LN-293442, and in part by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) under Grant TEC2016-79367-C2-2-R. The work of Carmen E. Domínguez-Flores and Osvaldo Rodríguez-Quiroz were supported by the CONACyT for Ph.D. Scholarship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Humidity sensor based on Bragg gratings developed on the end facet of an optical fiber by sputtering of one single material

  • Ascorbe Muruzabal, Joaquín
  • Corres Sanz, Jesús María
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
The refractive index of sputtered indium oxide nanocoatings has been altered just by changing the sputtering parameters, such as pressure. These induced changes have been exploited for the generation of a grating on the end facet of an optical fiber towards the development of wavelength-modulated optical fiber humidity sensors. A theoretical analysis has also been performed in order to study the different parameters involved in the fabrication of this optical structure and how they would affect the sensitivity of these devices. Experimental and theoretical results are in good agreement. A sensitivity of 150 pm/%RH was obtained for relative humidity changes from 20% to 60%. This kind of humidity sensors shows a maximum hysteresis of 1.3% relative humidity., This work was supported by the Spanish Economy and Competitiveness Ministry (TEC2016-79367-C2-2-R). Joaquín Ascorbe would like to thank the Public University of Navarra for the pre-doctoral fellowship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Development of an aptamer based luminescent optical fiber sensor for the continuous monitoring of Hg2+ in aqueous media

  • Acha Morrás, Nerea de
  • Elosúa Aguado, César
  • Arregui San Martín, Francisco Javier
A fluorescent optical fiber sensor for the detection of mercury (Hg2+) ions in aqueous solutions is presented in this work. The sensor was based on a fluorophore-labeled thymine (T)-rich oligodeoxyribonucleotide (ON) sequence that was directly immobilized onto the tip of a tapered optical fiber. In the presence of mercury ions, the formation of T–Hg2+-T mismatches quenches the fluorescence emission by the labeled fluorophore, which enables the measurement of Hg2+ ions in aqueous solutions. Thus, in contrast to commonly designed sensors, neither a fluorescence quencher nor a complementary ON sequence is required. The sensor presented a response time of 24.8 seconds toward 5 × 10−12 M Hg2+. It also showed both good reversibility (higher than the 95.8%) and selectivity: the I0 /I variation was 10 times higher for Hg2+ ions than for Mn2+ ions. Other contaminants examined (Co2+, Ag+, Cd2+, Ni2+, Ca2+, Pb2+, Mn2+, Zn2+, Fe3+, and Cu2+) presented an even lower interference. The limit of detection of the sensor was 4.73 × 10−13 M Hg2+ in buffer solution and 9.03 × 10−13 M Hg2+ in ultrapure water, and was also able to detect 5 × 10−12 M Hg2+ in tap water., This work was supported by the Spanish State Research Agency (AEI) and the Spanish Ministry of Economy and Competitiveness through the TEC2016-79367-C2-2-R project.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Recent developments in fiber optics humidity sensors

  • Ascorbe Muruzabal, Joaquín
  • Corres Sanz, Jesús María
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
A wide range of applications such as health, human comfort, agriculture, food processing and storage, and electronic manufacturing, among others, require fast and accurate measurement of humidity. Sensors based on optical fibers present several advantages over electronic sensors and great research efforts have been made in recent years in this field. The present paper reports the current trends of optical fiber humidity sensors. The evolution of optical structures developed towards humidity sensing, as well as the novel materials used for this purpose, will be analyzed. Well-known optical structures, such as long-period fiber gratings or fiber Bragg gratings, are still being studied towards an enhancement of their sensitivity. Sensors based on lossy mode resonances constitute a platform that combines high sensitivity with low complexity, both in terms of their fabrication process and the equipment required. Novel structures, such as resonators, are being studied in order to improve the resolution of humidity sensors. Moreover, recent research on polymer optical fibers suggests that the sensitivity of this kind of sensor has not yet reached its limit. Therefore, there is still room for improvement in terms of sensitivity and resolution., This work was supported by a Public University of Navarra PhD fellowship and by the Spanish Economy and Competitiveness Ministry TEC2016-79367-C2-2-R Research Grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Optical fiber sensors based on gold nanorods embedded in polymeric thin films

  • Urrutia Azcona, Aitor
  • Goicoechea Fernández, Javier
  • Rivero Fuente, Pedro J.
  • Pildain Lería, Ander
  • Arregui San Martín, Francisco Javier
In this work, we present a study about the generation and analysis of optical resonances caused by gold nanorods (GNRs) embedded in films. GNRs were embedded in polymeric thin films using the Layerby-Layer nanoassembly (LbL) deposition technique. Polymer/GNRs thin films of different thicknesses were deposited on the surface of cladding removed optical fibers for sensing. The spectral responses of the optical fiber sensors were monitored during the build-up of the thin films. The generation of two Localized Surface Plasmon Resonances (LSPRs) associated to the GNRs was observed in thinner coatings. These devices with around 12 polymer/GNRs bilayers were characterized as refractometers, providing an intensity-based sensitivity up to 75.69 dB/RIU. For thicker polymer/GNRs overlays, both LSPRs bands were also generated and, additionally, it was observed a new Lossy Mode Resonance (LMR) band due to modes coupled to the sensitive coating. The dependence of these three resonance bands with the surrounding refractive index was studied. Finally, these sensors were tested in a climatic chamber in the 20-90% relative humidity (RH) range and the LMR showed a good sensitivity to RH changes while the LSPR bands remained very stable in comparison. Results showed an excellent sensitivity of 11.2 nm/%RH for the LMR, confirming the potential of this type of optical fiber sensor based on the combination of LSPRs and LMRs bands., This work was supported in part by the Spanish Ministry of Economy and Competitiveness - CICYT-FEDER TEC2013-43679R, TEC2016-79367-C2-2-R, TEC2016-78047-R and TRA2013-48603-C4-1-R Research Grants, and a UPNA post-doctoral research grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Tesis doctoral (DoctoralThesis)

Luminescence-based optical fiber oxygen sensors fabricated by means of layer-by-layer nano-assembly

  • Acha Morrás, Nerea de
Over the last decades, luminescence quenching has been established as a widespread technique for gaseous oxygen monitoring in a broad range of applications. Thus, considerable effort has been made to manufacture luminescent oxygen sensors. The performances of such sensors are determined by the oxygen indicator and the matrix that entraps this indicator as well. In spite of its versatility for fine-tuning the final features of nanostructures, the Layer-by-Layer nano-assembly technique has been rarely studied for fabricating these sensors. This could be explained by the fact that most of the optically stable and highly sensitive oxygen indicators are not water soluble. The main objective of this work is to combine these detection and deposition techniques with optical fiber setups, for the fabrication and characterization of luminescent optical fiber oxygen sensors fabricated by Layer-by-Layer nano-assembly., This PhD thesis has been possible thanks to the pre-doctoral fellowship (reference BES-2014-069692) funded by the Spanish Ministry of Economy and Competitiveness through the TEC2013-43679-R project. This work has also been supported by the Spanish State Research Agency (AEI) and the European Regional Development Fund (ERDF-FEDER) through the TEC2016-79367-C2-2-R project and by the Government of Navarra Research Grants through the project Excelsen., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Interdigital concept in photonic sensors based on an array of lossy mode resonances

  • Domínguez Rodríguez, Ismel
  • Del Villar, Ignacio
  • Fuentes Lorenzo, Omar
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
Multi-parameter detection is key in the domain of sensors. Here it is demonstrated that an indium tin oxide (ITO) nanocoating can be used to generate multiple lossy mode resonances (LMRs) in the optical spectrum. To achieve this, a nanocoating with a gradient in thickness is generated on the surface of a planar waveguide, permitting broadening of the LMR because the position of an LMR in the optical spectrum is directly related to the nanocoating thickness. The nanocoating with a gradient in thickness contributes multiple LMRs, each one centred at a different wavelength. With a further etching or deposition using a mask, a pattern of deposited and non-deposited regions can be created, resulting in isolation of the LMRs by preventing LMR overlap. This enables tracking of each central wavelength separately, which can be tuned through control of the gradient or nanocoating pattern. The array of LMR-based sensors is a photonics analogue to the interdigital concept in electronics, enabling multiple resonances to be used for multiparameter sensing., The authors would like to acknowledge the partial support to the Spanish Ministry of Economy and Competitiveness TEC2016-79367-C2-2-R and PID2019-106231RB-I00 research fund, the STARDUST project (European Commission) and the pre-doctoral research grants of the Public University of Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Comparison between different structures of suspended-core microstructured optical fibers for volatiles sensing

  • López Torres, Diego
  • López Aldaba, Aitor
  • Elosúa Aguado, César
  • Auguste, Jean-Louis
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
  • Arregui San Martín, Francisco Javier
In this paper, different core structures of microstructured optical fibers (MOFs) for low-finesse Fabry-Perot (FP) sensors are experimentally compared to get the highest sensitivity. These devices are designed for volatile organic compounds (VOCs) measurements. Indium tin oxide (ITO) thin films were deposited by sputtering on the MOFs and different optical fast Fourier transform (FFT) phase responses from the FP were measured for saturated atmospheres of ethanol. It has been demonstrated that the sensitivities of the developed sensors depend strongly on the geometry and the dimensions of the MOF-cores. The sensors show recovery times shorter than 100 s and the baselines are fully recovered after every exposure to ethanol vapors., This research was funded by the financial support of MINECO (Spain) through TEC2016-79367-C2-2-R and TEC 2016-76021-C2-1-R as well as the FEDER funds and Public University of Navarre program PhD grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Artículo científico (JournalArticle)

Improving the width of lossy mode resonances in a reflection configuration D-shaped fiber by nanocoating laser ablation

  • Fuentes Lorenzo, Omar
  • Vaiano, Patrizio
  • Del Villar, Ignacio
  • Corres Sanz, Jesús María
  • Matías Maestro, Ignacio
The full width at half maximum (FWHM) of lossy mode resonances (LMRs) in the optical spectrum depends on the homogeneity of the thin film deposited. In this Letter, a method for improving the FWHM is applied for an LMR generated by a D-shaped optical fiber in reflection configuration. For this purpose, three samples with different attenuation were deposited with DC sputtering thin films of SnO2−x, and a further controlled immersion of the samples in water was performed. A laser-cleaner method was used to improve the FWHM characteristics of one of the samples from 106 to 53 nm. This improvement can be applied to thin-film-based sensors where there is a problem with the inhomogeneity of the coating thickness. Moreover, with this technique, it was proved that a coated length of just 3–4 mm permits the generation of an LMR, with implications for the miniaturization of the final device., Gobierno de Navarra, Ayuda a Movilidad Internacional 2019; Agencia Estatal de Investigación (TEC2016-79367-C2-2-R.).