Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biomass Ash and Phase Change Material (PCM) for Energy Efficiency of Sustainable Cement–Lime Composites

  • Guardia, Cynthia
  • Guerrero Bustos, Ana María
  • Barluenga, Gonzalo
This article belongs to the Special Issue Advances in Research on Phase Change Materials for Thermal Energy Storage Applications, Sustainability and nearly zero-energy consumption of new and existing buildings is a keystone in the new guidelines established by the European Commission. Likewise, waste management is in the focus of reducing the impact of industrial processes. The use of industrial byproducts, such as biomass ashes (BA), can be an interesting solution for waste valorization, reducing the carbon footprint and enhancing sustainability. In addition, Phase Change Materials (PCMs) can be used for improving energy efficiency due to their thermal storage capacity. An experimental study on the effect of biomass ash (BA) and PCM on the microstructure, chemical, physical and mechanical properties of cement–lime pastes was carried out. The partial replacement of cement with BA reduced compressive strength although did not substantially modify other paste properties, while the addition of PCM had a huge impact on microstructure and, therefore, physical and mechanical properties. PCM had a remarkable effect on thermal properties, endowing thermal storage capacity and reducing thermal conductivity, and the combination with BA further improved paste thermal properties., The authors acknowledge the financial support provided by the University of Alcalá (Spain), the Spanish Ministry of Universities and the European Union “Next Generation EU”—Margarita Salas Grant, awarded to Dr. Cynthia Guardia and the project CALTH3D (TED2021-132585B-I00) and RED2022-134219-T, funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033). The authors gratefully acknowledge the financial support from the European Commission through the Marie Skłodowska-Curie Actions (MSCA) under Grant Agreement ID: 101086440, BEST—Bio-based Energy-efficient Materials and Structures for Tomorrow project (https://doi.org/10.3030/101086440)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal energy storage-enhanced self-leveling mortars made of pre-placed perlite aggregates filled with bio-based phase change materials

  • Zanjani, Mahdi M.K.
  • Ferreira, Saulo Rocha
  • Lagazzo, Alberto
  • Basbus, Juan F.
  • Fachinotti, Victor D.
  • Caggiano, Antonio
Data will be made available on request., This study investigates the development and performance of self-leveling mortars (SLMs) enhanced with Phase Change Materials (PCMs) and expanded perlite aggregates to provide Thermal Energy Storage (TES) functionality for energy-efficient buildings. A cementitious encapsulation method was used to coat PCM-saturated perlite, forming durable macro-encapsulated aggregates. To preserve the structural integrity of these inclusions during casting, the pre-placed aggregate method was employed in combination with a highly flowable self-consolidating mortar matrix. Three mortar formulations were produced and analyzed: (a) reference SLM, (b) SLM with expanded perlite, and (c) SLM with PCM-filled perlite. Thermal performance was assessed through dynamic “DKK” tests and a custom ASTM C1363-19 Hot-Box apparatus. Tests revealed that PCM-enhanced mortars achieved the highest thermal buffering effect, exhibiting plateaus at 25–30 °C and reduced heat flux values. The apparent thermal conductivity, during the PCM phase change, dropped to 0.28 W/(m·K), demonstrating effective latent heat absorption. The results clearly demonstrate enhanced passive thermal regulation with delayed heat transfer responses, supporting the use of PCM-perlite SLMs as energy-storage building materials. Complementary tests were then performed to verify the material, mechanical, and durability feasibility of the composites. Mechanical tests showed that the reference SLM achieved the highest compressive and flexural strengths, at 60.14 MPa and 5.79 MPa, respectively. The incorporation of expanded perlite reduced the compressive strength to 29.02 MPa, while PCM-enhanced aggregates further reduced it to 17.62 MPa. A slight improvement in flexural strength was observed for the PCM composite (i.e., 3.46 MPa) compared to the uncoated perlite (3.08 MPa), indicating potential reinforcement by the encapsulation shell. Water absorption tests revealed that PCM-enhanced perlite mortars exhibited low absorption within the first 180 min but experienced a sharp increase at 72 h (i.e., 3 days), surpassing all other mixes and suggesting long-term permeability issues. SEM-EDS analyses indicated high Ca/Si ratios (∼7.75) in the shell, and TGA results showed minimal portlandite decomposition, both supporting the hypothesis of calcium hydroxide consumption by silica fume to form additional C–S–H gels. Overall, PCM-perlite SLMs show strong potential for TES-enabled building applications., This work was supported within the framework of the following projects/grants: PRIN 2022 project OPTIMA (OPTImized use of phase change MAterials for energy and seismic retrofitting of buildings). Project Code 2022MP7A4C, funded by the Italian Ministry of University and Research (MUR) under the PRIN 2022 call, in accordance with the Decree of the Secretary General No. 1401 of 18 September 2024, for the period 2025–2027. European Union – Horizon 2020 Marie Skłodowska-Curie Actions: HORIZON-TMA-MSCA-SE-2021 “BEST – Bio-based Energy-efficient Materials and Structures for Tomorrow” (Grant Agreement No. 101086440, DOI: 10.3030/101086440). HORIZON-MSCA-2023-PF-01-01 - MSCA “SMART-NRG – Solutions for constructions and building materials based on Energy Absorption”, Marie Skłodowska-Curie Postdoctoral Fellowship (Grant Agreement No. 101153320, DOI 10.3030/101153320). Work Package WP5 – “Interventi integrati e sostenibili per costruzioni esistenti” (Coordinated by Prof. F. da Porto and Prof. A. Prota), as part of the DPC-ReLUIS 2024–2026 projects funded by the Dipartimento della Protezione Civile. Italian National Recovery and Resilience Plan (PNRR), Mission 4 “Education and Research”, Component 1, Investment 3.4 “Transnational Education (TNE)”, funded by the European Union – NextGenerationEU, under the MUR Directorial Decree prot. no. 167 of 03 October 2023, “Avviso per la concessione di finanziamenti destinati a iniziative educative transnazionali”, within the project TNE23-00074 “Fragility, Marginality, Mobility, Energy Transition – FraMMET”, CUP C96G23000270001., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thermal energy storage-enhanced self-leveling mortars made of pre-placed perlite aggregates filled with bio-based phase change materials

  • Zanjani, Mahdi M.K.
  • Ferreira, Saulo Rocha
  • Lagazzo, Alberto
  • Basbus, Juan F.
  • Fachinotti, Victor D.
  • Caggiano, Antonio
This study investigates the development and performance of self-leveling mortars (SLMs) enhanced with Phase Change Materials (PCMs) and expanded perlite aggregates to provide Thermal Energy Storage (TES) functionality for energy-efficient buildings. A cementitious encapsulation method was used to coat PCM-saturated perlite, forming durable macro-encapsulated aggregates. To preserve the structural integrity of these inclusions during casting, the pre-placed aggregate method was employed in combination with a highly flowable self-consolidating mortar matrix. Three mortar formulations were produced and analyzed: (a) reference SLM, (b) SLM with expanded perlite, and (c) SLM with PCM-filled perlite. Thermal performance was assessed through dynamic “DKK” tests and a custom ASTM C1363-19 Hot-Box apparatus. Tests revealed that PCM-enhanced mortars achieved the highest thermal buffering effect, exhibiting plateaus at 25–30 °C and reduced heat flux values. The apparent thermal conductivity, during the PCM phase change, dropped to 0.28 W/(m·K), demonstrating effective latent heat absorption. The results clearly demonstrate enhanced passive thermal regulation with delayed heat transfer responses, supporting the use of PCM-perlite SLMs as energy-storage building materials. Complementary tests were then performed to verify the material, mechanical, and durability feasibility of the composites. Mechanical tests showed that the reference SLM achieved the highest compressive and flexural strengths, at 60.14 MPa and 5.79 MPa, respectively. The incorporation of expanded perlite reduced the compressive strength to 29.02 MPa, while PCM-enhanced aggregates further reduced it to 17.62 MPa. A slight improvement in flexural strength was observed for the PCM composite (i.e., 3.46 MPa) compared to the uncoated perlite (3.08 MPa), indicating potential reinforcement by the encapsulation shell. Water absorption tests revealed that PCM-enhanced perlite mortars exhibited low absorption within the first 180 min but experienced a sharp increase at 72 h (i.e., 3 days), surpassing all other mixes and suggesting long-term permeability issues. SEM-EDS analyses indicated high Ca/Si ratios (∼7.75) in the shell, and TGA results showed minimal portlandite decomposition, both supporting the hypothesis of calcium hydroxide consumption by silica fume to form additional C–S–H gels. Overall, PCM-perlite SLMs show strong potential for TES-enabled building applications.
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Early age and hardened properties of 3D printable cement-lime mortars with microencapsulated PCM and cellulose microfibers

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The design of sustainable functionalized materials suitable for new building technologies has become a challenge for the construction sector. In this study, 3D printable cement-lime mortars incorporating microencapsulated phase change material (PCM) and cellulose microfibers (CMF) were designed and experimentally characterized considering the requirements for architectural applications. The use of lime aims to reduce environmental impact, PCM intends to enhance thermal performance and CMF to provide early age integrity. Two reference mortars were designed, with and without CMF, and PCM was incorporated at 10, 20 and 30% into both reference mixtures. An experimental program was carried out evaluating mortars’ fresh state rheological properties, early age performance and short- and long-term hardened-state physical, thermal and mechanical properties. Long- term carbonation was also assessed. The experimental approach provided a comprehensive understanding of how these components interact across all relevant stages of material development, from fresh state to long-term performance. Lime densified mortar matrix, due to carbonation, contributing to strength gain and reducing water absorption. PCM improved thermal behavior by enhancing their energy storage capacity up to a 35 – 40%, while CMF mitigated early age setting delays in mixtures containing PCM but reduced the thermal storage enhancement at PCM contents above 20%., European Commission, Junta de Castilla-La Mancha
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Piezoresistivity in self-compacting concrete mixes with hybrid additions of carbon fibers and nanofibers

  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
SMARTINCS"23 Conference on Self-Healing, Multifunctional and Advanced Repair Technologies in Cementitious Systems, Self-sensing properties of concrete structures can be achieved through the incorporation of additions in carbon-based materials (CBM) that modify electrical properties and provide piezoresistive (PZR) properties to the cement paste. PZR in pastes and mortar mixes with different types of carbon-based materials such as fibers of different sizes has been extensively tested. However, very limited studies on selfsensing properties in concrete are available due to the lower content of paste volume that leads to a decrease of concrete PZR. However, self-compacting concrete (SCC) can be an ideal candidate to implement PZR, due to two fundamental traits: the larger amount of paste of SCC compared to a conventional concrete and larger volumetric fraction of fiber can be incorporated due to a reduced effect on SCC workability and consistency. The present study aims to assess PZR properties of SCC with carbon-based components of different sizes. Combining carbon nanofibers (NFC) and carbon fibers (CF), in hybrid systems, could lead to obtain SCC with self-sensing properties identifying their effectiveness thresholds. The self-detection performance of PZR-SCC samples under mechanical stress was verified by resistivity and PZR experimental tests., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Sisal fiber reinforced mortar for 3D printing applications in construction

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Pimentel Tinoco, Matheus
  • Mendoza Reales, Óscar Aurelio
  • Dias Toledo Filho, Romildo
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The use short fibers in mortars can address some issues for 3D printing (3DP) technology, providing reinforcing and improving material sustainability. Among fibers, Sisal fiber (SF) is a good option for mortar reinforcement due to its natural origin, irregular cross-section and high flexibility. The aim of this study was to assess fresh and hardened properties of sisal fibers on 3D printable bio-based mortars for architectural applications. A 3D printable reference mortar with a 0-0.6 sand and a water to cement ratio of 0.45 was designed. The reference mortar was reinforced with 0.5, 1 and 1.5% volumetric fraction (VF) of 13 mm length SF and with 1% VF of a shorter SF of 6.5 mm length. An experimental evaluation of 3DP mortars comprising several rheological parameters at fresh state and physical and mechanical properties in hardened state was carried out to assess mortars? extrudability, printability and hardened performance. Printability was also evaluated by trials using a manual extruder and a robotic 3D printer. It was found that SF reduced mortar consistency initially and over time, modifying effective thixotropy. On the other hand, the length and amount of SF and the casting procedure showed differences on the physical and mechanical properties. Mortars with small SF amounts showed good printability while higher amounts were prone to clog the 3DP pumping system., Comisión Europea (Fondos Next Generation), Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Biomass ash and phase change material (PCM) for energy efficiency of sustainable cement-lime composites

  • Guardia Martín, Cynthia|||0000-0003-4442-8933
  • Guerrero Bustos, Ana
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Sustainability and nearly zero-energy consumption of new and existing buildings is a keystone in the new guidelines established by the European Commission. Likewise, waste management is in the focus of reducing the impact of industrial processes. The use of industrial byproducts, such as biomass ashes (BA), can be an interesting solution for waste valorization, reducing the carbon footprint and enhancing sustainability. In addition, Phase Change Materials (PCMs) can be used for improving energy efficiency due to their thermal storage capacity. An experimental study on the effect of biomass ash (BA) and PCM on the microstructure, chemical, physical and mechanical properties of cement–lime pastes was carried out. The partial replacement of cement with BA reduced compressive strength although did not substantially modify other paste properties, while the addition of PCM had a huge impact on microstructure and, therefore, physical and mechanical properties. PCM had a remarkable effect on thermal properties, endowing thermal storage capacity and reducing thermal conductivity, and the combination with BA further improved paste thermal properties., Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Experimental results and numerical analysis of capillary water absorption of lime-cement mortars with PCM and cellulose fibres for 3DP applications

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Caggiano, Antonio
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Artículos completos del congreso MECOM 2025, This study assesses the moisture transport phenomena of 3D printing lime-cement mortars with Phase Change Materials (PCM) and Cellulose Fibers (F) for architectural applications comparing experimental results and numerical analyses. A lime-cement control mortar was designed and cellulose fibers and different percentages of PCM (i.e., 10, 20 and 30%) were added, leading to a total of eight different mixtures. Physical and mechanical characterization tests were performed on mortar samples and capillary water absorption tests were carried out over 24h. Based on the experimental results, a computational nonlinear FE-based Moisture Diffusion model was calibrated to simulate the data., Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Bio-based self-modulating thermal and moisture buffer mortars for architectural applications

  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Varela Recio, Hugo|||0000-0001-8094-6071
New construction materials for architectural applications need to face environmental impact and energy efficiency issues. Self-modulating materials are promising solutions to optimize the energy performance of buildings, by compensating climatic hygro-thermal changes. Phase-change materials (PCM) and Superabsorbent polymers (SAP) highlight among bio-based components that can be used to design self-modulating mortars. On one hand, PCM can storage and release thermal energy, modulating heat flow and reducing heating and cooling energy demand. On the other, SAP can help to achieve suitable indoor conditions as they level air humidity and contribute to an evaporative cooling effect. In addition, these polymeric materials can be made from renewable bio-resources, becoming bio-based materials. This paper presents a study reporting materials selection, mortar composition design and experimental tests and procedures used to assess thermal and moisture self-modulating properties of PCM and SAP modified mortars for architectural applications as buffer layers. A pervious cement-lime mixture was designed and different amounts and combinations of two types of SAP (spherical and irregular particle shape) and a microencapsulated PCM were evaluated. Mortars? fresh workability and setting and hardened physical and mechanical properties, microstructure, thermal (heat conductivity and storage properties) and hygric parameters (water and vapor transport and storage) and long term carbonation were studied. The preliminary results of self-modulating mortars showed that SAP and PCM can increase moisture and thermal properties, enhancing buffer capacities of architectural mortar renderings., Comunidad de Madrid, Universidad de Alcalá, Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

3D printable cement-based composites reinforced with Sisal fibers: Rheology, printability and hardened properties

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Pimentel Tinoco, Matheus
  • Mendoza Reales, Óscar Aurelio
  • Toledo Filho, Romildo Dias
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Reinforcement of cement-based systems is one of the main unsolved issues for 3D printing technology (3DP). The use of short fibers is a promising way to improve cement-based systems fresh and hardened strength, overcoming this limitation. Among natural fibers, Sisal fibers (SF) can be an excellent option, due to their irregular crosssection morphology, water retention capacity and high Young modulus. In this study, fresh and hardened properties of 3D printable cement-limestone filler mortar reinforced with 1 % volumetric fraction (VF) of 6.5 mm SF and 0.5, 1 and 1.5 % VF of 13 mm SF was assessed. Fresh state mortar rheology was evaluated using flow table test (FT), Self-weight cone-penetration (WCP), Displacement-controlled cone-penetration (DCP) and fresh squeeze tests (SQT). 3DP was evaluated on mortars using a manual extruder and a 3D cartesian robotic printer. Hardened physical and mechanical properties were tested, comparing the effect of 3DP and SF reinforcement on conventional and 3D printed specimens. It was observed that SF slightly modified mortars" rheology and cohesiveness, while SF improved fresh mechanical behavior and enhanced flexural strength and toughness index (IT) on hardened state, due to SF alignment produced by 3DP. Water capillarity and open porosity was also modified by 3DP, due to particle squeezing and fiber´s alignment during extrusion. Higher VF and longer fibers reduced robotic printability and produced discontinuities and pumping blockage, showing limits for SF addition., Comisión Europea (Fondos Next Generation), Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Printability assessment of 3D printing cement-lime mortars with microencapsulated PCM

  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
An experimental study was conducted to evaluate the printability of cement–lime mortars designed for 3D printing applications, incorporating a microencapsulated phase-change material (PCM) and cellulose microfibers (CMFs). The influence of both PCM and CMFs on mortars’ rheology was measured by rheometer tests (DSR) and cone penetration tests (CPT). A ram extrusion test was used to evaluate the extrudability, and an unconfined uniaxial compression test (UUCT) allowed the assessment of buildability. Finally, several lab-scale prototypes were 3D-printed. The results showed that the incorporation of PCM affected mortar’s rheology and workability due to the reduction in paste volume and the increase in superplasticizer (SP) demand. However, the spherical particle shape of microencapsulated PCM was found to ease the extrusion process. After being extruded, mortars with lower volumetric fractions of PCM exhibited increased fresh strength and stiffness, whereas larger amounts reduced both parameters. The use of CMFs considerably reduced the extrusion force and improved the extrusion quality. Lab-scale 3D-printed prototypes were successfully manufactured using mortars with a 20% volumetric fraction of PCM., European Commission, Junta de Comunidades de Castilla-La Mancha