Pasar al contenido principal

RED ESPAÑOLA EN ALMACENAMIENTO DE ENERGIA TERMICA

RED2022-134219-T

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Redes Investigación /Redes Excelencia
Año convocatoria 2022
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE LLEIDA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 110
Encontrada(s) 2 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Use of molten salts tanks for seasonal thermal energy storage for high penetration of renewable energies in the grid

  • Prieto, Cristina
  • Tagle-Salazar, Pablo D.
  • Patiño-Rodríguez, David
  • Schallenberg-Rodriguez, Julieta
  • Lyons, Padraig
  • Cabeza, Luisa F.
Energy storage is acknowledged a key technology to meet the challenges posed by the energy transition. Shortterm grid-connected storage, based on Li-Ion batteries, is becoming commonplace but seasonal energy storage at grid-scale will be needed for deep decarbonisation of the electrical power system. Pumped hydropower is considered to be the only mature technology for such applications, but this paper demonstrates that two-tanks molten salts systems, that are used today in commercial concentrating solar power (CSP) plants, can also be considered a mature technology that can be used at large scale for seasonal energy storage. This was established by evaluating the annual heat losses of molten salts tanks using validated models of these systems. The results show that the heat losses in a very well insulated molten salts tanks are around 1 K/day, which would result in good economic performance of the power block even if storage was required for up to months., This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación de España (PID2021-123511OB-C31 - MCIU/AEI/FEDER, UE; RED2022-134219-T). The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Use of artificial intelligence methods in designing thermal energy storage tanks: A bibliometric analysis

  • Mehraj, Nadiya
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
This bibliometric study examines the use of artificial intelligence (AI) methods, such as machine learning (ML) and deep learning (DL), in the design of thermal energy storage (TES) tanks. TES tanks are essential parts of energy storage systems, and improving their design has a big impact on how effectively and sustainably energy is used. With the increasing availability and advancements in AI techniques, researchers explored their application within the field of TES tank design to address challenges related to structural analysis, material selection, and optimization. However, a comprehensive analysis of the current state of research, trends, and potential areas for improvement is lacking. This study aims to bridge this gap by analysing scientific papers, patents, and publications in conference proceedings from the Scopus database to identify trends, research gaps, and areas of importance in this domain. The novelty of this study lies in its focused examination of AI methods specifically applied to TES tank design, providing a unique perspective on the intersection of these two important fields. By conducting a thorough bibliometric analysis, this study offers original insights into the current landscape and future directions of AI-enabled TES tank design research. The methodology involves a systematic search query and the use of VOSviewer software for keyword analysis. The results indicate a notable increase in publications during recent years (2020-August 2023), aligning with the growing focus on sustainable energy solutions. The most frequent keywords, such as TES, genetic algorithm (GA), and phase change material (PCM), suggest a focus on improving optimization of TES tanks with AI, while the least common keywords highlight specific areas with limited work and opportunities for future studies. In conclusion, this bibliometric analysis underscores the potential of AI to enhance the design and performance of TES tanks, emphasizes the value of further research in this area, and identifies opportunities for future advancements in AI-enabled TES tank design to contribute to energy efficiency and sustainability efforts., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU; TED2021-129462B-I00; and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to their research group (2021 SGR 01615). GREiA is TECNIO a certified agents in the category of technological development of the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Increasing the sustainability of buildings by using thermal energy storage

  • Cabeza, Luisa F.
  • Zsembinszki, Gabriel
  • Palomba, Valeria
  • Borri, Emiliano
  • Lapka, Miloslav
  • Mateu Piñol, Carles
  • Beyne, Wim
  • Mani Kala, Saranprabhu
The final energy consumption of the built environment depends on the mismatch between its instantaneous energy demand and the energy supplied by on-site sources: buildings need to be cooled when there is abundant environmental heat and heated when the surrounding environment is cold. Thermal energy storage (TES) can help to reduce the global warming potential of buildings by storing environmental, renewable or waste heat for later use when heating is needed. In this Review, we assess the economic, environmental and social aspects of TES technologies. TES tanks require high charging and discharging power, calling for the development of new heat exchangers and storage media, such as phase-change materials. Integrating TES into local energy communities could reduce energy costs and lower the emissions caused by space and water heating, but challenges remain: price volatility and the deployment of longer-term thermochemical TES for seasonal storage, for example. The efficiency of TES operation could be increased by using advanced control systems, including artificial intelligence techniques. With the development of increasingly complex systems for TES, we highlight the importance of circular design thinking and end-user engagement in optimizing the development and deployment of future TES systems., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). The authors at the University of Lleida thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA inside the program ICREA Academia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental evaluation of different macro-encapsulation designs for PCM storages for cooling applications

  • Rehman, Omais Abdur
  • Palomba, Valeria
  • Vérez, David
  • Borri, Emiliano
  • Frazzica, Andrea
  • Brancato, Vincenza
  • Botargues, Teresa
  • Ure, Zafer
  • Cabeza, Luisa F.
Extensive research has been conducted on utilizing phase change materials for cooling applications, making it one of the most explored techniques in this domain. This research paper presents a comprehensive performance evaluation of a latent heat thermal energy storage unit featuring three distinct macro-encapsulation designs for phase change materials. The study aims to assess the thermal performance, efficiency, and practical applicability of these macro-encapsulation designs in a storage system. The PCM macro-encapsulation designs under investigation include cylindrical and rectangular shapes, each possessing different geometry. Two different configurations have been considered in this study. One configuration contains same PCM mass in order to have similar storage capacity while the other configuration has maximum PCM mass that can be inserted inside the tank. The used phase change material is a salt hydrate with melting temperature of 17 °C. The experimental setup consists of a controlled test rig that simulates real-world conditions and enables the comparative analysis of the three designs. Key performance parameters such as the charging and discharging time, temperature profiles, heat transfer rate, and energy storage/retrieval rates are measured and analysed. The results obtained from the experimental study provide valuable insights into the thermal behaviour, energy storage capacity, and overall effectiveness of the three macro-encapsulation designs. It is important to mention that use of an encapsulation design is highly dependent on application. The findings of this study contribute to the understanding of the impact of different macro-encapsulation designs on performance of thermal energy storage units. The results serve as a basis for optimizing macro-encapsulation designs, improving the efficiency and reliability of latent heat storage systems, and promoting their wider adoption in various energy management applications., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 101007976 (CO-COOL). This work is partially supported by ICREA under the ICREA Academia programme. This work is also partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021- 123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal Properties and Pore Structure of Electric Arc Furnace Slag Mortars for Solar-Exposed Building Components

  • Sucupira, Luciana
  • Zsembinszki, Gabriel
  • Risco Amigó, Sara
  • Castro-Gomes, João
  • Cabeza, Luisa F.
The valorisation of electric arc furnace (EAF) slag in construction materials can reduce the consumption of virgin raw materials while creating opportunities for CO2 mineralisation. However, the combined influence of EAF slag aggregate, aggregate particle-size range and biochar addition on the mechanical, pore-structure and thermal behaviour of carbonated mortars remains insufficiently understood. This study investigated mortars produced with EAF slag as binder and, in selected formulations, as aggregate, with and without biochar. Three aggregate particle-size ranges were assessed: 0.5–1 mm, 1–2 mm, and 2–4 mm. After static compaction and accelerated carbonation, the mortars were characterised in terms of compressive strength, degree of carbonation, pore structure, thermal conductivity, heat-storage capacity and dynamic thermal response. The 100% EAF slag mixtures achieved the highest carbonation degrees, reaching 32.62% for the 1–2 mm formulation containing biochar. Among the tested mixtures, formulation 3C, consisting of 100% EAF slag without biochar and with a particle-size range of 1–2 mm, showed the most balanced overall performance, with a compressive strength of 17.91 MPa, a carbonation degree of 32.13%, a porosity of 24.01%, a thermal conductivity of 0.804 W m−1 K−1, a specific heat capacity of 884 J kg−1 K−1 and a thermal lag of 1.22 h. Although the thermal lag was limited for the 4 cm-thick specimens, the results indicate potential for carbonated EAF-slag mortars to contribute as functional layers in solar-exposed multilayer building components requiring mechanical integrity and short-term heat storage., This work was supported by FCT—Fundação para a Ciência e Tecnologia, I.P., of Research Unit C-MADE, Centre of Materials and Building Technologies, by project reference UIDB/04082/2020 and DOI identifier <https://doi.org/10.54499/UIDB/04082/2020>. The study also received support from the Marie Skłodowska-Curie Actions “Research and Innovation Staff Exchange (MSCA RISE) program” through the project “CSTO2NE—Biomimicry and carbon adsorbent eco-materials for a climate-neutral economy” (project reference 101086302). The Ministerio de Ciencia e Innovación partially funded this work—Agencia Estatal de Investigación (AEI)—NextGeneration EU (PID2021- 123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Numerical analysis of an optimal metal wool-phase change material for thermal energy storage with exceptionally high power density

  • Ribezzo, Alessandro
  • Morciano, Matteo
  • Zsembinszki, Gabriel
  • Mani Kala, Saranprabhu
  • Borri, Emiliano
  • Bergamasco, Luca
  • Fasano, Matteo
  • Chiavazzo, Eliodoro
  • Prieto, Cristina
  • Cabeza, Luisa F.
The adoption of thermal energy storage (TES) systems based on phase change material (PCM) remains limited by their low thermal conductivity, which restricts power density. Existing heat transfer enhancement techniques are often costly or come with significant drawbacks, leaving a gap for an effective and affordable solution. This study highlights metal wool as a promising alternative, offering low cost, ease of application, and retrofitting potential. While previous experiments demonstrated substantial improvements in power density using copper wool, a comprehensive numerical model to further optimize this technique is presented here. The model, incorporating CFD simulations and uncertainty analysis, was validated for bulk PCM and two copper wool-PCM composites before being extended to a wool material analysis. First, possible alternatives to copper as wool material were tested, highlighting aluminum as a viable candidate. Then, the proposed composite was found to match the discharging performance of a PCM with an effective thermal conductivity of 2.5 W/mK, a value rarely achieved by conventional enhancement techniques. Additionally, a techno-economic comparison revealed that copper wool delivered a 14.7-fold increase in thermal conductivity relative to liquid PCM at ¿6 per kg of PCM additivated¿a performance unmet by metal foams and nanocomposites. These findings confirm metal wool as a viable cost-effective and high-performance solution for improving TES systems, partially bridging the gap between efficiency and affordability., A.R. and E.C. acknowledge funding under the National Recovery and Resilience Plan (NRRP), Mission 4 Component 2 Investment 1.3—Call for tender No. 1561 of 11.10.2022 of Ministero dell’Università e della Ricerca (MUR); funded by the European Union—NextGenerationEU. This work was partially funded by the Ministerio de Ciencia e Innovacion’ - Agencia Estatal de Investigacion’ (AEI) (PID2021-123511OB-C31-MCIN/AEI/10.13039/501100011033/ FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Department de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/ 10.13039/501100011033 and FSE+. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 101036910
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Use of Textile Fiber Waste to Improve the Thermal and Mechanical Performance of Cement-Based Mortar

  • Ayed, Rabeb
  • Borri, Emiliano
  • Zsembinszki, Gabriel
  • Bouadila, Salwa
  • Cabeza, Luisa F.
  • Lazaar, Mariem
Ayed, R., Borri, E., Zsembinszki, G., Bouadila, S., Cabeza, L.F., Lazaar, M. (2024). Use of Textile Fiber Waste to Improve the Thermal and Mechanical Performance of Cement-Based Mortar. In: Ungureanu, V., Bragança, L., Baniotopoulos, C., Abdalla, K.M. (eds) 4th International Conference "Coordinating Engineering for Sustainability and Resilience" & Midterm Conference of CircularB “Implementation of Circular Economy in the Built Environment”. CESARE 2024. Lecture Notes in Civil Engineering, vol 489. Springer, Cham. https://doi.org/10.1007/978-3-031-57800-7_25, Improving the thermal properties of materials used in buildings is crucial to reducing energy demand and consumption. This study investigated the use of textile fiber waste in cement-based composites for construction applications. Mechanical and thermal characterizations were carried out to assess the behavior of cement mortars with different percentages of two types of textile fibers after 7 and 28 days of water hardening. The results show that the incorporation of fibers can significantly improve the thermal insulation capacity of buildings by reducing the thermal conductivity of cement mortar by up to 52%. In addition, the use of textile fibers can improve themechanical strength of the cement mortar, especially with a high fiber content and a longer curing time., The authors would like to thank the Research and Technology Center of Energy of Borj-Cedria, Tunisia, Ministry of Higher Education and Scientific Research for supporting this study. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This publication is based upon work from COST Action CircularB, supported by COST (European Cooperation in Science and Technology). The authors from GREiA Research Group would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREAAcademia programme.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Evaluation of the social impact of an energy system for residential heating applications based on a novel seasonal thermal energy storage

  • Borri, Emiliano
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Thermal energy storage (TES) is a key player in the energy transition to support the integration of renewable sources and reduce the energy demand supplied by fossil fuels. The EU-funded project SWS-Heating aims to develop a novel seasonal thermal energy storage based on selective water sorbents for domestic heating to increase the share of renewables. Although the main performance indicator of new technologies is energy efficiency optimization, social impact of TES is an overlooked aspect representing a strong barrier to market deployment of novel technologies. Therefore, this study uses social life-cycle assessment (S-LCA) techniques to evaluate the social impact of the proposed systems described above. The inventory developed in this study is based on qualitative data from industrial companies involved in the different stages of the system life cycle. Results showed that the system has a medium-high social impact with great potential for improvement especially in the manufacturing and end-of-life stages. In particular, to increase the value of social impact more effort should be put by companies to strengthen the engagement with local communities and support sustainability with value chain actors., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 764025 (SWS-HEATING). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021 - 123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA within the ICREA Academia programme.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

AI-aided design of high-performance thermal energy storage systems inspired by nature (Nit Europea de la Recerca 2024)

  • Mehraj, Nadiya
Renewable energy communities (REC) represent a pivotal paradigm shift in energy management, emphasizing collective action and shared resources to address environmental challenges by enabling members to pool their renewable energy resources and distribute surplus energy where it is needed most. Through collaboration and energy sharing, these communities not only reduce reliance on fossil fuels but also promote local resilience and autonomy in energy production. Thermal energy storage systems could play an important role in maximizing the effectiveness of renewable energy sharing and consumption within communities. They efficiently store excess renewable energy, ensuring its availability when needed most, thereby enhancing the reliability and stability of local energy networks while minimizing wastage., This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-12351108-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU), and by Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This project is co-funded by the European Union's research and innovation programme Horizon Europe under the project NtRecercat2425 (101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

A technical and economic comparison between concrete and latent thermal energy storage for concentrated solar power applications

  • Prieto, Cristina
  • Borri, Emiliano
  • Pavón Moreno, M. Carmen
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Thermal energy storage (TES) plays a key role in concentrating solar power (CSP) plants by enhancing dispatchability and improving overall system efficiency. This study presents a comparative techno-economic analysis of three TES configurations integrated into CSP plants: (i) the conventional two-tank molten salt system, (ii) a phase change material (PCM)-based system with a cascade arrangement, and (iii) a concrete-based system. While technical performance simulations indicate similar annual energy production across all cases, significant differences emerge in economic viability. The PCM TES system demonstrates the lowest levelized cost of electricity (LCoE) at $14.35/kWh, leveraging its high energy density and reduced material requirements, despite lower efficiency (93 % compared to 99 % in molten salt). Conversely, the concrete TES system, while capable of extended discharge at partial loads, incurs higher parasitic losses and investment costs, resulting in a higher LCoE ($16.16/kWh). The cost analysis further highlights the cost-performance quotient (CPQ) as a valuable metric for assessing TES competitiveness, with PCM exhibiting the most favorable CPQ of $1.04/kWh. These findings underscore the necessity of integrating economic assessments into TES selection for CSP plants. Moreover, the study identifies opportunities for cost reduction in concrete TES through optimized modular designs and improved material formulations. This work provides valuable insights for policymakers, engineers, and industry stakeholders aiming to enhance the financial feasibility of next-generation CSP storage solutions., This study receives funding from the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/PRTR“. CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors from University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Desarrollo y optimización de nuevos PCM en base a sales inorgánicas, para su aplicación en sistemas de almacenamiento de energía térmica a altas temperaturas (Nit Europea de la Recerca 2023)

  • Martínez, Franklin R.
Las plantas de concentración solar de potencia (CSP) son instalaciones industriales donde se aprovecha la radiación solar para producir energía eléctrica. Sin embargo, los costos de instalación de estas plantas son elevados. Reemplazar los tanques de sales fundidas por un tanque de PCM en cascada es una alternativa atractiva que ayuda a la reducción significativa de los costos de instalación., F. Rodrigo Martínez Alcocer agradece a la Beca de Doctorado Nacional para estudiantes extranjeros ANID 2021 (Folio 21211932) por el apoyo financiero en la investigación. Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) y el Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen al Gobierno de Cataluña la acreditación de calidad concedida al grupo de investigación GREiA (2021 SGR 01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos del Gobierno de Cataluña. Este trabajo está parcialmente apoyado por ICREA dentro del programa ICREA Academia. Este trabajo está cofinanciado por el programa de investigación e innovación Horizon Europe de la Unión Europea bajo el proyecto NitRecerCat (GA 101061189).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Hardware-in-the-loop tecniques for complex systems analysis: Bibliometric analysis of available literature

  • Cabeza, Luisa F.
  • Vérez, David
  • Teixidó Cairol, Mercè
Simulating complex systems in real time presents both significant advantages and challenges. Hardware-in-the-loop (HIL) simulation has emerged as an interesting technique for addressing these challenges. While HIL has gained attention in the scientific literature, its application in energy studies and power systems remains scattered and challenging to locate. This paper aims to provide an assessment of the penetration of the HIL technique in energy studies and power systems. The analysis of the literature reveals that HIL is predominantly employed in evaluating electrical systems (smart grids, microgrids, wind systems), with limited application in thermal energy systems (energy storage). Notably, the combination of electrical hardware-in-the-loop (EHIL) and thermal hardware-in-the-loop (THIL) techniques has found application in the assessment of vehicle thermal management systems and smart cities and, recently, has also been adopted in building systems. The findings highlight the potential for further exploration and expansion of the HIL technique in diverse energy domains, emphasizing the need for addressing challenges such as hardware-software compatibility, real-time data acquisition, and system complexity., This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615) and the GRIHO research group (2021 SGR 01620). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA inside the program ICREA Academia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal energy storage in energy communities: A perspective overview through a bibliometric analysis

  • Brunelli, Luca
  • Borri, Emiliano
  • Pisello, Anna Laura
  • Nicolini, Andrea
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
The climate and energy crisis requires immediate countermeasures. Renewable energy communities (RECs) are capable of enhancing the consumption of renewable energy, involving citizens with a leading role in the energy transition process. The main objective of a REC is to maximize the consumption of renewable energy by reducing the mismatch between energy supply and demand. This is possible through the use of strategies and technologies including energy storage systems. Among these, the use of thermal energy storage (TES) is an efficient strategy due to the lower investment required compared to other storage technologies, like electric batteries. This study aims to define the role of TES in RECs, through a bibliometric analysis, in order to highlight research trends and possible gaps. This study shows that the existing literature on TES does not present terms related to RECs, thus presenting a research gap. On the other hand, RESs address the topic of energy storage in the literature, without focusing on TES in particular but considering the general aspect of the topic. Therefore, this leaves open a possibility for the development of research on TES as a possible technology applied to a REC to maximize the renewable energy sharing., Funding: This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE) and by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). L. Brunelli acknowledges Fondazione Perugia for the support given through the “EDUCER” project (21082, 2022.0406). Acknowledgments: The authors at the University of Lleida thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA inside the program ICREA Academia. L. Brunelli aknowledgments are due to the PhD school in Energy and Sustainable Development at CIRIAF from the University of Perugia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Artificial intelligence and thermal energy storage: A review of design techniques and applications

  • Mehraj, Nadiya
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
Thermal energy storage systems (TES) are becoming increasingly popular owing to its great energy capacity and efficiency. However, traditional TES design methods are often time-consuming, and due to the intricate and nonlinear nature of such systems, the results could be unreliable. The design and improvement of TES has made use of artificial intelligence (AI) techniques such artificial neural networks, fuzzy logic, evolutionary algorithms, and machine learning models. This review paper offered a thorough analysis of AI techniques for TES system design and optimization, comparing them to conventional design approaches, outlining the benefits and drawbacks of AI optimization techniques, and discussing how AI was used in TES systems. The purpose of the study was to define the existing issues, opportunities, and prospects for research in this field, as well as to provide advice for researchers, practitioners, and policymakers about the selection and deployment of AI approaches for TES system design. The article showed how AI techniques had the potential to improve the functionality, effectiveness, and long-term viability of TES systems by looking at recent research and cases., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU, TED2021-129462B-I00, and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to their research groups (2021 SGR 01615). GREiA is TECNIO a certified agents in the category of technological development of the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Development of copper metal wool incorporated in a latent thermal energy storage tank for improved charging and discharging

  • Mani Kala, Saranprabhu
  • Ribezzo, Alessandro
  • Zsembinszki, Gabriel
  • Borri, Emiliano
  • Prieto, Cristina
  • Cabeza, Luisa F.
The thermal energy storage tank is an essential component of a conventional thermal energy storage system. Nevertheless, low charging and discharging rates is one of the different problems associated with them. Many research studies were conducted to improve the charging and discharging characteristics of thermal energy storage tanks. Those include the addition of nanoparticles, heat pipes, metal foams, and encapsulation of the phase change material. Even though those approaches improved the thermal performance of the storage tank, they also promoted some problems, like nanoparticle deposition, suppression of natural convection, and reduced energy density. This study, used a different approach to improve the thermal performance, integrating copper metal wool of two discrete thicknesses perpendicular to the heat transfer fluid carrying tubes. Accordingly, with two different packaging factor four different configurations of metal wool-packed tanks were developed and compared against the reference, i.e., a conventional shell and tube tank. The thermal performance of the developed cases was tested using a custom-built test rig. The integration of copper metal wool reduced the charging and discharging time significantly. However, the fully stacked fine fibre wool packed tank showed a remarkable 85% reduction in solidification time and a 37.4% reduction in melting time compared to the conventional shell and tube tank. Moreover, it showed a higher mean power than all the developed cases, with 414% enhancement during the discharging cycle and 42% during the charging cycle. Thus, the incorporation of metal wool into a tank is an effective way to enhance its thermal performance., This project has received funding from the European Union’s Horizon 2020 Research and Innovation Programme under Grant Agreement N. 101036910 (StoRIES). This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors at the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal energy storage for direct steam generation concentrating solar power plants: Concept and materials selection

  • Prieto, Cristina
  • Cabeza, Luisa F.
  • Pavón Moreno, M. Carmen
  • Palomo, Elena
Direct steam generation (DSG) concentrating solar power (CSP) plants uses water as heat transfer fluid, and it is a technology available today. It has many advantages, but its deployment is limited due to the lack of an adequate long-term thermal energy storage (TES) system. This paper presents a new TES concept for DSG CSP plants. This system is based on three blocks, a saturated block based on phase change materials, an overheating block that elevates the vapor temperature of a heat transfer fluid to the desired values, and a preheating block that increases the temperature difference between a cold tank and a hot tank of a non-phase change thermal storage material. After a deep selection and characterization process, the material to be used is LiOH/KOH, since although it has the disadvantage of high corrosion, the identified advantages overcome it as an ideal PCM for this process., This work was partially funded by the Ministerio de Ciencia e Innovacion ´ de Espana ˜ [(TED2021-132216A-I00) (ITC-20111061- FEDER-Innterconecta-Composol), (PID2021-123511OB-C31 - MCIU/ AEI/FEDER, UE), and (RED2022-134219-T)]. The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2017 SGR 1537). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Desarrollo de una herramienta computacional de simulación de sistemas de almacenamiento térmico (TES) para plantas de concentración solar (Nit Europea de la Recerca 2023)

  • Tagle-Salazar, Pablo D.
¿Qué es un Sistema de Almacenamiento de Energía Térmica? Sistema que “guarda” energía en forma de calor en períodos de alta producción (día) para usarlo como fuente en períodos de alta demanda (noche). Esto permite obtener una generación de potencia más estable, disminuyendo los efectos de la intermitencia solar., Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31-MCIN/AEI/10.13039/501100011033/FEDER, UE) y el Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen al Gobierno de Cataluña la acreditación de calidad concedida al grupo de investigación GREiA (2021 SGR 01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos del Gobierno de Cataluña. Este trabajo está parcialmente apoyado por ICREA dentro del programa ICREA Academia. El proyecto NitRecerCat (GA 101061189) está cofinanciado por el programa de investigación e innovación Horizonte Europa de la Unión Europea.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Potential of the Use of Sodium Chloride (NaCl) in ThermalEnergy Storage Applications

  • Cabeza, Luisa F.
  • Martínez, Franklin R.
  • Zsembinszki, Gabriel
  • Borri, Emiliano
Energy storage is a group of technologies that decrease the gap between energy supply and energy demand. Thermal energy storage (TES) reduces this gap at not only different temperatures but also at different places or power. Design criteria include the integration of the storage system into the whole application system, maximum load, and high-energy density. Since energy density is given by the material used, the selection of the storage material is key to the success of any energy storage system. In this paper, the potential of sodium chloride (NaCl) to be used in TES, both using sensible TES and latent TES, is evaluated for low-temperature applications and for high-temperature ones. This material is found to have high potential for successful applications, both in buildings and in industry., This work was partially funded by the Ministerio de Ciencia eInnovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB - C31—MCI N/A E I/10.13 039/5 0110 0 011033/ F E DER ,UE), and Ministerio de Ciencia e Innovación—Agencia Estatal deInvestigación (AEI) (RED2022-134219-T). Franklin R. MartinezAlcocer thanks the National Doctorate Scholarship for foreign stu-dents ANID 2021 Folio 21211932 for the financial support in the re-search. This work is partially supported by ICREA under the ICREAAcademia program. The authors would like to thank the CatalanGovernment for the quality accreditation given to their research group(2021 SGR 01615). GREiA is a certified agent of TECNIO in the cate-gory of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Innovative refractory concrete for high temperature thermal energy storage

  • Castro Chicot, José Ramón
  • Santini, Carolina
  • Zsembinszki, Gabriel
  • Mani Kala, Saranprabhu
  • Martínez, Franklin R.
  • Risco Amigó, Santiago
  • Fabiani, Claudia
  • Pisello, Anna Laura
  • Cabeza, Luisa F.
Thermal energy storage (TES) systems play an important role in the management of thermal energy and associated consumption. Furthermore, using TES, combustion of fossil fuels and their associated environmental impacts are avoided. In particular, demand for high temperature energy storage is increasing and research focuses on the development of suitable materials for these applications. A limited number of studies focus on the use of sensible heat storage systems that exploit concrete as a TES under high temperature conditions for concentrating solar power (CSP) plant systems. The main drawback to overcome in concrete TES is the degradation of the concrete after charging and discharging thermal cycles. This study aims to develop a novel concrete formulation designed for high-temperature applications and capable of withstanding thermal cycling. To achieve this, a refractory concrete was conceptualized using calcium aluminate cement (CAC) and refractory aggregates, specifically basalt and chamotte. The formulation also incorporates a heat treatment applied after the cu[[ring period to enhance its performance under extreme thermal conditions. This heat treatment is what allows to transform a CAC concrete, that unites the dispersed material through hydraulic nodes, into a refractory concrete, that unites the dispersed material through its ceramisation. The new concrete formulation was analysed to evaluate its performance before and after 25 thermal cycles. Results show that thermal conductivity and compressive strength after ceramisation have values around 1.7 W/m⋅K and 52 MPa, respectively. It was also observed that the initial thermal treatment was not necessary, because the ceramisation of the concrete can also be achieved during the thermal cycling process if the correct heating and cooling rates are used. The developed new concrete formulation containing refractory aggregates demonstrated excellent thermo-physical and mechanical properties that make it suitable for high-temperature TES applications (temperatures up to 700 ◦C)., This project has received funding from the European Union's Horizon 2020 Research and Innovation Programme under Grant Agreement 101036910 (StoRIES). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This study received funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU"/PRTR". The authors from University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme. This work was partially funded by the European Union—NextGenerationEU under Italian Ministry of University and Research (MUR) National Innovation Ecosystem grants ECS00000041— VITALITY—CUP J97G22000170005 and CUP B43C22000470005. The authors thank the PhD school in Energy and Sustainable Development at CIRIAF University of Perugia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental characterization of phase change materials for thermal energy storage for solar energy applications in the temperature range between 400 ºC and 600 ºC

  • Martínez, Franklin R.
  • Borri, Emiliano
  • Ushak, Svetlana
  • Mani Kala, Saranprabhu
  • Prieto, Cristina
  • Cabeza, Luisa F.
Concentrating solar power (CSP) plants are seen as a key technology to achieve the needed energy transition since its use together with a thermal energy storage (TES) system ensures electricity dispatchability decreasing CSP plants environmental impact and life cycle costs. Latent TES using phase change materials (PCMs) has risen as a very interesting storage technology for such applications. Nevertheless, the selection of the adequate TES system and PCM, is one of the problems researchers and practitioners face to implement such technology. This paper presents a full characterization of fifteen PCMs suitable to work in the temperature range 400-600 ◦C. Melting temperature, melting enthalpy, degradation temperature, and solid-state thermal conductivity are presented, complemented with corrosion behaviour tests against stainless steel and Alloy 20. Moreover, the findings obtained in the characterization of the selected fifteen PCMs highlight the need of these analyses, as notable differences were observed compared to the available data, particularly in thermal stability and thermal conductivity. Furthermore, the compatibility test reveals that out of the fifteen selected PCMs, only two PCMs (binary mixtures of carbonates) are potentially compatible with stainless-steel 314 and Alloy 20 fibres under environmental conditions (air atmosphere). Finally, the results presented will allow researchers and practitioners to have very detailed data on the characterisation of those PCMs., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE, and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N° 1523A0006 and ANID/FONDECYT REGULAR N° 1231721 projects.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Analysis on integration of heat pumps and thermal energy storage in current energy system: From research outputs to energy policies

  • Rehman, Omais Abdur
  • Borri, Emiliano
  • Palomba, Valeria
  • Frazzica, Andrea
  • Brancato, Vincenza
  • Botargues, Teresa
  • Cabeza, Luisa F.
This paper presents a comprehensive examination of the integration of heat pumps and thermal energy storage (TES) within the current energy system. Utilizing bibliometric analysis, recent research trends and gaps are identified, shedding light on the evolving landscape of this dynamic field. The study delves into the research outputs since 1969, offering insights into the global scholarly contributions shaping the discourse. Furthermore, an extensive policy analysis is conducted, focusing on seven countries with the highest research output. The interplay between research advancements and energy policies is explored, providing an understanding of the practical implications of the integration of heat pumps and TES. An understanding is tried to reach as how research and policy sector influence each other. This analysis contributes not only to the academic understanding of the subject but also informs policymakers about potential pathways for enhancing energy efficiency and sustainability in heating and cooling sector., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 101007976 (CO-COOL). This work is partially supported by ICREA under the ICREA Academia programme. This work is also partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Modelat de tancs d’emmagatzematge d’energia tèrmica mitjançant l’ús d’eines d’intel·ligència artificial

  • Rojas Cala, Edgar Felipe
Les fonts d’energia renovable s’enfronten a múltiples desafiaments, entre els quals hi ha la necessitat de garantir una producció contínua. Una solució a aquest problema és l’emmagatzematge de l’energia generada per utilitzar-la en moments en què aquestes fonts no siguin eficients. Una alternativa viable és l’emmagatzematge d’energia tèrmica (TES, per les seves sigles en anglès). Aquesta tecnologia consisteix en un sistema format per una part de transport i una altra d’emmagatzematge, essent aquesta darrera especialment important, ja que permet reduir les pèrdues energètiques i augmentar l’eficiència del sistema. modelatge la simulació de l’emmagatzematge d’energia tèrmica, concretament mitjançant dinàmica de fluids computacional (CFD, per les seves sigles en anglès), requereix habitualment eines especialitzades, personal qualificat i una inversió considerable tant en recursos computacionals com econòmics. En aquest context, aquest estudi proposa una alternativa més accessible i eficient als mètodes convencionals de modelatge: l’ús d’eines d’intel·ligència artificial (IA) per a la simulació de dipòsits TES. La recerca va començar amb una revisió de l’estat de la qüestió, on es va identificar una oportunitat de desenvolupament deguda a un buit existent en l’aplicació de la IA al modelatge de dipòsits TES. A partir d’aquesta troballa, es va dur a terme una primera fase experimental utilitzant un disseny senzill de dipòsit TES. Es va entrenar un model de xarxa neuronal amb dades generades mitjançant simulacions CFD convencionals. Els resultats obtinguts van ser prometedors i van evidenciar el potencial d’aquesta aproximació per a una implementació a major escala. En una segona etapa, la recerca es va orientar al desenvolupament d’una eina d’IA més robusta, versàtil i escalable per al modelatge de dipòsits TES. Es van establir dos objectius principals: primer, modelar el comportament del dipòsit en diferents moments temporals; segon, permetre que el model es pogués generalitzar a diferents configuracions de dipòsit, variant la quantitat de components interns. Ambdues línies de treball van donar resultats encoratjadors. Tanmateix, es va fer evident la necessitat d’una recerca més profunda i multidisciplinària que abordi altres aspectes rellevants, amb l’objectiu de desenvolupar una eina capaç de substituir els mètodes actuals de modelatge de dipòsits TES., Aquest treball està parcialment finançat pel Ministeri de Ciència i Innovació - Agència Estatal de Recerca (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) i el Ministeri de Ciència, Innovació Estatal de Recerca (AEI) (RED2022-134219-T). ). Els autors agraeixen a la Generalitat de Catalunya l’acreditació de qualitat concedida al grup de recerca GREiA (2021 SGR 01615). GREiA és un agent certificat TECNIO en la categoria de desenvolupadors tecnològics de la Generalitat de Catalunya. Aquest treball està parcialment secundat per ICREA dins del programa ICREA Academia. Aquest projecte está cofinançat pel programa de recerca i innovació de la Unió Europea Horizon Europe, en el marc del projecte NitRecercat2425 (101162003).
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Desarrollo de una herramienta computacional de simulación de sistemas de almacenamiento térmico para plantas de concentración solar

  • Tagle-Salazar, Pablo D.
La concentración solar es una tecnología que convierte la luz del sol en electricidad. Funciona concentrando los rayos solares en un receptor, lo que calienta un fluido a 565 °C. Este calor se utiliza para generar vapor y mover una turbina que produce electricidad. Sin embargo, la producción de electricidad se detiene al anochecer. Para solucionar esto, se emplea un sistema de almacenamiento de energía que guarda el exceso de calor generado durante el día y lo libera por la noche. Esto asegura un suministro constante de energía, eficiente y sostenible, incluso cuando no existe solo. Buscamos desarrollar un programa computacional que simule el funcionamiento de plantas solares acoplado a diferentes tipos de almacenamiento de energía térmica, con el fin de comparar el rendimiento de estas plantas y visualizar la influencia de los distintos esquemas para almacenar calor en la producción de energía., Este trabajo está parcialmente financiado por el Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T) y el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE). Este trabajo está parcialmente apoyado por ICREA dentro del programa ICREA Academia. Los autores agradecen al Departament de Recerca i Universitats de la Generalitat de Catalunya la acreditación de calidad otorgada a su grupo de investigación (2021 SGR 01615). GREiA es agente certificado TECNIO en la categoría de desarrolladores tecnológicos de la Generalitat de Catalunya.. Este proyecto está cofinanciado por el programa de investigación e innovación de la Unión Europea Horizonte Europa, dentro del proyecto NitRecercat2425 (101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Compatibility of carbonate mixtures to be used as molten salts with different metal alloys to be used as container materials

  • Cabeza, Luisa F.
  • Martínez, Franklin R.
  • Borri, Emiliano
The energy transition can only be achieved if the global energy sector is transformed from a fossil-based system to a zero-carbon-based source system. To achieve this aim, two technologies have shown promising advances in high-temperature application. Concentrating solar power (CSP) plants are seen as a key technology to achieve the needed energy transition, and carbon dioxide (CO2) capture and storage (CCS) is a promising technology for decarbonizing the industrial sector. To implement both technologies, molten carbonate salts are considered promising material. However, their corrosive behavior needs to be evaluated, especially at high temperatures, where corrosion is more aggressive in metal structures. This paper presents an experimental evaluation of the static corrosion of two molten carbonate salts, a Li2CO3-Na2CO3-K2CO3-LiOH·H2O (56.65-12.19-26.66-4.51wt.%) mixture and a Li2CO3 salt, under an air atmosphere with five corrosion-resistant metal alloys, including Alloy 600, Alloy 601, Alloy 625, Alloy 214, and Alloy X1. In this study, the corrosion rate and mass losses were quantified. In addition, in all the cases, the results of the experimental evaluation showed corrosion rate values between 0.0009 mg/cm2·yr and 0.0089 mg/cm2·yr., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE), and Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N° 1522A0006 and ANID/FONDECYT REGULAR N° 1231721 projects. This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the company STAX for their contribution to the study.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Investigation of melting process in a PCM-based modular shell-and-coil latent thermal energy storage unit filled with coconut oil using image-processing-based techniques

  • Andrzejczyk, Rafał
  • Rogowski , Michał
  • Saqib, Muhammad
  • Muszyński, Tomasz
  • Cabeza, Luisa F.
This study explores the melting of coconut oil, a biodegradable phase-change material, in a shell-and-coil latent heat thermal energy storage unit under a constant heat flux of 519 W/m2, optimized through prior parametric studies of coil geometries and boundary conditions. A novel image processing approach, implemented via MATLAB's Image Segmenter, employs two distinct methods to analyze the melting process. The first method uses binarization to quantify the liquid fraction, revealing exponential growth that confirms convection-driven heat transfer, enhanced by coconut oil's low thermal conductivity. The second method calculates the equivalent diameter of the melting front, based on the coil's elliptical shape, to track its spatial progression. Compared to volume-averaged temperature calculations, the liquid fraction shows good initial agreement but diverges after 2000s due to image processing limitations, such as sensitivity to lighting and coil boundary effects. A theoretical model for melting front thickness was developed, though further experiments are needed for generalization. With low heat flux uncertainty this study underscores the potential of image processing for non-intrusive analysis of complex LTES geometries, advancing designs for low-temperature applications like solar thermal systems. The following study will be used to develop an enhanced and optimized model for complex geometries based on image processing techniques in the future., This research work was supported by the National Centre for Research and Development, Poland (Project No. LIDER/4/0008/L-9/ 17/NCBR/2018). Special thanks to Mr. Przemysław Kozak and PhD Michal Fabrykiewicz who were Lider project team members. This work was partially funded by the Ministerio de Ciencia e Innovacion ´ - Agencia Estatal de Investigacion ´ (AEI) (PID2021-123511OB-C31 - MCIN/AEI/1 0.13039/501100011033/FEDER, UE and RED2022-134219-T). Dr. Cabeza would also like to thank the Generalitat de Catalunya for the quality accreditation granted to her research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers of the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Enhancement of heat transfer through the incorporation of copper metal wool in latent heat thermal energy storage systems

  • Ribezzo, Alessandro
  • Morciano, Matteo
  • Zsembinszki, Gabriel
  • Risco Amigó, Santiago
  • Mani Kala, Saranprabhu
  • Borri, Emiliano
  • Bergamasco, Luca
  • Fasano, Matteo
  • Chiavazzo, Eliodoro
  • Prieto, Cristina
  • Cabeza, Luisa F.
The design of thermal energy storage (TES) tank is the key part that can limit charging and discharging process. Most research findings highlight that the use of fins augments the heat transfer rate. This work experimentally investigates the use of aligned copper wools as fillers to enhance the thermal performance of a lab-scale shelland- tube TES tank filled with phase change material (PCM). Two copper wools with different fibre thicknesses were chosen and discretely laid around the TES tank tubes in two design patterns. Accordingly, five shell-andtube TES tank configurations were obtained, including the reference, for performance evaluation. The TES tank was loaded with n-octadecane as PCM for all the cases studied. The results showed up to a 16 % reduction in melting time with the inclusion of copper wool. The TES tank significantly increased the mean power during charging (53 %) and discharging (205 %). The addition of metal wool into the TES tank enables the PCM to release the heat at a constant temperature during the entire phase transition process. And the overall efficiency of the TES tank was found to get improved. Therefore, a copper wool integrated TES tank would be a beneficial addition to thermal energy storage systems., This project was funded by the European Union's Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Department de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Assessing the impact of copper wools on a phase change material-based TES tank prototype

  • Ribezzo, Alessandro
  • Morciano, Matteo
  • Zsembinszki, Gabriel
  • Risco Amigó, Santiago
  • Mani Kala, Saranprabhu
  • Borri, Emiliano
  • Bergamasco, Luca
  • Fasano, Matteo
  • Chiavazzo, Eliodoro
  • Cabeza, Luisa F.
Comunicació presentada al 9th European Thermal Sciences Conference (Eurotherm 2024), Lake Bled, Slovenia, 10-13 de juny de 2024., Phase Change Materials (PCMs) stand out as a promising solution within the current array of Thermal Energy Storage (TES) technologies, thanks to their superior energy storage capacities (compared to sensible solutions) and technological readiness. Nonetheless, the limited thermal conductivity of these materials may lead to incomplete phase transitions during use, resulting in a decrease in their effective energy storage capabilities. The major solutions to mitigate this issue that are present in literature either require a significant modification in the heat exchanger design (e.g. by fins) or are costly and still lack robustness and reliability (e.g. by additivities). In this study, the use of copper wools is proposed as fillers within a PCM-based heat exchanger prototype, and the assessment of its impact on the heat transfer behaviour of the material is evaluated by performing charging and discharging processes. This type of inclusion was chosen as it is relatively cheap, it can be implemented within an already existing heat exchanger, and it does not suffer from segregation. Two different wools were tested in two configurations, thus resulting in five test cases (four containing the wools and one containing solely PCM). The promising results, especially the remarkable decrease in the time needed for the complete solidification of the PCM within the tank (up to 67%), open the opportunity to additional numerical analyses regarding different configurations and/or materials, thus possibly targeting further optimizations in terms of the specific energy density and the specific power density., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recercai Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Partial support of the Italian National Project PRIN Heat transfer and Thermal Energy Storage Enhancement by Foams and Nanoparticles (2017F7KZWS) is also acknowledged.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Renewable Energy Community Integration: sharing of renewable through thermal energy storage technology

  • Brunelli, Luca
Renewable energy communities (REC) represent a pivotal paradigm shift in energy management, emphasizing collective action and shared resources to address environmental challenges, by enabling members to pool their renewable energy resources, and distribute surplus energy where it is needed most. Through collaboration and energy sharing, these communities not only reduce reliance on fossil fuels but also promote local resilience and autonomy in energy production. Thermal energy storage systems could play an important role in maximizing the effectiveness of renewable energy sharing and consumption. within communities. They efficiently store excess renewable energy, ensuring its availability when needed most, thereby enhancing the reliability and stability of local energy networks while minimizing wastage., This work is partially supported by ICREA under the ICREA Academia programme. The authors would lke to thank the Departament de Recerca | Universitats of the Catalan Government for the quallty accreditation glven to their research. This project is co-funded by the group (2021 SGR 01615). GREA Is certified agent TECNIO In the category of technology developers from the European Union's Govemnment of Cataionia. This work was partully funded by the Ministerio de Ciencla e Innovacidn - Aencla Estatal de Innovation programme Horizon Europe, Investigación (AEI) (PID2021-12351108-C31 - MCIN/AE1/10.13039/501100011033/FEDER, UE), and by Miniterio de Ciencia e Innovación - Agencia Estatal de Investigaoón (AEI) (RED2022-134219-T). This project is co-funded by the European Union’s research and innovation programme Horizon Europe, under the project NtRecercat2425 (101162003).
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Desarrollo y optimización de nuevos PCM en base a sales inorgánicas, para su aplicación en sistemas de almacenamiento de energía térmica a altas temperaturas (Nit Europea de la Recerca 2024)

  • Martínez, Franklin R.
Las plantas de concentración solar de potencia CSP, son instalaciones industriales donde se aprovecha la radiación solar para producir energía eléctrica. Los rayos solares son reflejados desde una superficie extensa y concentrados en un solo punto (superficie reducida) para calentar el fluido calo portador (HTF) a una temperatura de 565ºC, este fluido caliente ingresa al intercambiador de calor donde cede al agua el calor acumulado, produciendo vapor, el cual ingresa a la turbina donde se genera energía eléctrica., Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) y el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen a la Generalitat de Catalunya la acreditación de calidad concedida al grupo de investigación GREiA (2021 SGR 01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos de la Generalitat de Catalunya. Este trabajo está parcialmente respaldado por ICREA dentro del programa ICREA Academia. Este proyecto está cofinanciado por el programa de investigación e innovación de la Unión Europea Horizon Europe, en el marco del proyecto NitRecercat2425 (101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Environmental performance of a multi-energy liquid air energy storage (LAES) system in cogeneration asset – A life cycle assessment-based comparison with lithium ion (Li-ion) battery

  • Tafone, Alessio
  • Borri, Emiliano
  • Cabeza, Luisa F.
  • Romagnoli, Alessandro
Increase in energy demand is shaping both developed and developing countries globally. As a result, the endeavour to reduce carbon emissions also encompasses electrical energy storage systems to ensure environmentally friendly power production and distribution. Currently, the scientific community is actively exploring and developing new storage technologies for this purpose. The focus of this work is to compare the eco-friendliness of a relatively novel technology such as liquid air energy storage (LAES) with an established storage solution such as Li-Ion battery (Li-ion). The comparison is carried out through Life Cycle Assessment (LCA) methodology which aims to assess the environmental impacts from each life stage, according to different impact categories. In particular, the study refers to the unitary storage and the delivery of electricity as well as cooling energy, considering all the inefficiencies and limits of each technology. The results show that in the full electric case study Li-ion battery environmentally outperform LAES due to (1) the higher round trip efficiency and (2) the significantly high environmental impact of the diathermic oil utilized by LAES, accounting for 92 % of the manufacture and disposal phase. Conversely, the cogeneration case study highlights that the “flexibility” and “dualism” of LAES, capable to efficiently deliver both electricity and cooling, offset the impact related to the higher electricity consumption during the use phase. Notably in energy mix frameworks with high share of primary energy source from fossil fuels, cogenerative LAES demonstrates superior environmental performance compared to Li-ion battery (i.e. 1302 kgCO2eq/MWhe vs 1140 kgCO2eq/MWhe for Singapore energy mix), attributable to its reduced electricity consumption., This project was funded by the European Union’s Horizon 2020 Research and Innovation Programme under No. 101007976 (COCOOL). This work is partially supported by ICREA under the ICREA Academia programme. This work is also partially funded by Ministerio de Ciencia e Innovacion´ —Agencia Estatal de Investigacion ´ (AEI) (PID2021- 123511OB-C31 - MCIN/AEI/10.13039/ 501100011033/FEDER, EU and RED2022-134219-T). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal Energy Storage Using Phase Change Materials in High-Temperature Industrial Applications: Multi-Criteria Selection of the Adequate Material

  • Cabeza, Luisa F.
  • Martínez, Franklin R.
  • Borri, Emiliano
  • Ushak, Svetlana
  • Prieto, Cristina
Thermal energy storage (TES) plays an important role in industrial applications with intermittent generation of thermal energy. In particular, the implementation of latent heat thermal energy storage (LHTES) technology in industrial thermal processes has shown promising results, significantly reducing sensible heat losses. However, in order to implement this technology, a proper selection of materials is important. In this study, a new multi-criteria phase change material (PCM) selection methodology is presented, which considers relevant factors from an application and material handling point of view, such as hygroscopicity, metal compatibility (corrosion), level hazard, cost, and thermal and atmospheric stability. The methodology starts after setting up the system requirements where the PCM will be used, then a material screening is able to find all possible candidates that are listed with all available properties as listed before. Then, a color map is produced, with a qualitative assessment of material properties drawbacks, hazard level, melting enthalpy, and price. The experimentation starts with a preliminary set of tests on hygroscopicity and one-week corrosion test, which allows disregarding PCMs and selecting a short list of potential PCMs that would need further characterization before the final selection., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE), and Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N◦ 1522A0006 and ANID/FONDECYT REGULAR N◦ 1231721 projects.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Energy saving potential of variable thermophysical envelope energy storage technologies in different climatic regions

  • Ji, Pengcheng
  • Guo, Yong
  • Weschler, Louise B.
  • Cabeza, Luisa F.
  • Zsembinszki, Gabriel
  • Yang, Rui
  • Zhang, Yinping
Climate change mitigation necessitates higher use of renewable energy in buildings instead of fossil fuels. There is great potential to achieve this goal when the thermophysical properties of a building envelope are variable. To identify the ideal variable thermophysical properties (specific heat and thermal conductivity) for building envelopes located in given climate regions, an inverse problem approach based on particle swarm optimization (PSO) was employed. The energy consumptions of rooms were calculated when the building envelope thermophysical properties are ideally variable or constant for seven representative cities located in five climatic regions in China. The results show that when the thermal conductivity of exterior wall is ideally variable, the energysaving ratio can reach 7-15 % in seven cities, corresponding to energy saving amount of 0.03-0.78 kgce/(m2⋅year), and when the specific heat of interior building envelope is ideally variable, the energy saving ratio can reach 37-100 %, corresponding to energy saving amount of 0.21-3.06 kgce/(m2⋅year). The corresponding annual CO2 emission reduction is between 0.02 and 1.90 kg/(m2⋅year) and between 0.10 and 8.07 kg/(m2⋅year), respectively. Variable thermophysical properties have highest energy-saving and CO2 emission reduction potential in the severe cold region. Conversely, in the moderate temperature region, their impact is insignificant. The present study can help to provide direction for developing materials ith variable thermophysical properties for building envelopes in different climate regions., The research was supported by Natural Science Foundation of China (51976106, 52378102). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors from the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Methodology for the Prediction of the Thermal Conductivity of Concrete by Using Neural Networks

  • Rosa, Ana Carolina
  • Elomari, Youssef
  • Calderón, Alejandro
  • Mateu Piñol, Carles
  • Haddad, Assed
  • Boer, Dieter
The energy consumption of buildings presents a significant concern, which has led to a demand for materials with better thermal performance. Thermal conductivity (TC), among the most relevant thermal properties, is essential to address this demand. This study introduces a methodology integrating a Multilayer Perceptron (MLP) and a Generative Adversarial Network (GAN) to predict the TC of concrete based on its mass composition and density. Three scenarios using experimental data from published papers and synthetic data are compared and reveal the model’s outstanding performance across training, validation, and test datasets. Notably, the MLP trained on the GAN-augmented dataset outperforms the one with the real dataset, demonstrating remarkable consistency between the model’s predictions and the actual values. Achieving an RMSE of 0.0244 and an R2 of 0.9975, these outcomes can offer precise quantitative information and advance energy-efficient materials., The authors would like to acknowledge financial support from the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES), Finance Code 001, Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq), Fundação de Amparo à Pesquisa do Estado do Rio de Janeiro (Faperj) 2019-E-26/202.568/2019 (245653), and “Ministerio de Ciencia, Innovación y Universidades” of Spain [PID2021-127713OA-I00, PID2021-123511OB-C32, PID2021-123511OB-C33, PID2021-124139NB-C22-MCIN/AEI/10.13039/501100011033/FEDER, EU, TED2021-129851B-I00- /AEI/10.13039/501100011033/Unión Europea NextGenerationEU/PRTR and RED2022-134219-T]
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Integration of thermal energy storage (TES) technologies in buildings (Nit Europea de la Recerca 2024)

  • Ahmed, Waqar
1. What is thermal energy? What does thermal energy storage mean? Thermal energy is the energy that comes from heat. It's the energy that helps to keep things warm or cool. Thermal energy storage is a way to save heat or cold so you can use it later when you need it. 2. What does thermal energy storage (TES) do in buildings? TES helps to keep buildings warm in winter and cool in summer by storing heat or cold and using it when needed. A building with good TES system, we can reduce heating bills and use less energy from the electricity grid., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE), and by Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia This project is co-funded by the European Union’s research and innovation programme Horizon Europe, under the project NitRecercat2425 (101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Development of a bio-inspired TES tank for heat transfer enhancement in latent heat thermal energy storage systems

  • Cabeza, Luisa F.
  • Mani Kala, Saranprabhu
  • Zsembinszki, Gabriel
  • Vérez, David
  • Risco Amigó, Santiago
  • Borri, Emiliano
Thermal energy storage (TES) systems play a very important part in addressing the energy crisis. Therefore, numerous researchers are striving to improve the efficiency of TES tanks. The TES technology has the potential to reach new heights when the biological behavior of nature is incorporated into the design of TES tanks. By mimicking the branched vein pattern observed in plants and animals, the heat transfer fluid (HTF) tube of a TES tank can enhance the heat transfer surface area, hence improving its thermal efficiency without the need to add other enhancements of heat transfer methods. Accordingly, in this study, a unique additive-manufacturing-based bio-inspired TES tank was designed, developed, and tested. A customized testing setup was used to assess the bio-inspired TES tank's thermal performance. A comparison was made between the bio-inspired TES tank and a conventional shell-and-tube TES tank. The latent TES system's thermal performance was significantly enhanced by the biomimetic approach for the design of a TES tank, even before the optimization of its design. The results showed that, compared to the shell-and-tube TES tank, the bio-inspired TES tank had a higher discharging rate and needed 52% less time to release the stored heat., This study has received funding from the European Union’s Horizon Europe Research and Innovation Programme under grant agreement No. 101103552 (SUSHEAT). However, the views and opinions expressed are those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE), Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI)—NextGeneration EU (TED2021-129462B-I00—MCIN/AEI/10.13039/501100011033/NextGenerationEU/PRTR), and Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work was partially supported by ICREA under the ICREA Academia program.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Integration of thermal energy storage (TES) technologies in buildings (Nit Europea de la Recerca 2025)

  • Ahmed, Waqar
Thermal energy is the energy that comes from heat. It is the energy that helps to keep things warm or cool. Thermal energy storage (TES) is a way to save heat or cold so you can use it later when you need it. TES helps to keep buildings warm in winter and cool in summer by storing heat or cold and using it when needed. In a building with a good TES system, we can reduce heating bills and use less energy from the electricity grid., This project is also co-funded by the European Union’s project BIOBUILD (GA 101135629). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/501100011033/FEDER, UE) and by the Ministerio de Ciencia e Innovación y Universidades – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is also supported by the RYC2023-044196-L, funded by MCIN/AEI/10.13039/501100011033 and FSE+. This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is a certified TECNIO agent in the category of technology developers of the Government of Catalonia. This project is co-funded by the European Union’s research and innovation programme Horizon Europe under the project NitRecercat (GA 101162003).
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Use of bibliometric analysis to evaluate the influence of cement and concrete on carbon capture, utilization, and storage over the years

  • Santini, Carolina
Cement industry produced high quantities of CO2 increasing the concept of concrete as a nonsustainable material. This work aim to analyse all the relevant research focused on CO2 capture, utilization and storage (CCUS) in cement-concrete sector., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE), and by Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia This project is co-funded by the European Union’s research and innovation programme Horizon Europe, under the project NitRecercat2425 (101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Failure analysis of the leakage and ignition of heat transfer fluid in a concentrating solar power (CSP) pilot plant

  • Prieto, Cristina
  • López-Román, Antón
  • Cabeza, Luisa F.
Concentrating solar power (CSP) is a technology seen key to achieve the worldwide energy transition targets. Although it is a mature robust technology, different failures in CSP plant have been reported in the literature to visualize potential point of maintenance interest. Following the same philosophy, this paper reports a failure occurred at a CSP storage pilot plant, where leakage and ignition of different joint balls suddenly occurred after several hours of testing. The experimental assessment carried out confirmed spontaneous ignition of the heat transfer fluid-soaked insulation material of the piping after leakage. The results of this study emphasize the significance of proactive maintenance and daily inspections in solar fields., This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación de España (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 1615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Experimental evaluation of different macro-encapsulation designs for PCM storages for cooling applications

  • Rehman, Omais Abdur
This research activity presents a comprehensive performance evaluation of a latent heat thermal energy storage unit featuring three distinct macro-encapsulation designs for phase change materials. The study aims to assess the thermal performance, efficiency, and practical applicability of these macro-encapsulation designs within an energy storage system., Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31-MCIN/AEI/10.13039/501100011033/FEDER, UE) y por el Ministerio de Ciencia, Innovación y Universidades – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen al Gobierno de Cataluña la acreditación de calidad concedida al grupo de investigación GREiA (2021SGR01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos por el Gobierno de Cataluña. Este trabajo está parcialmente apoyado por ICREA en el marco del programa ICREA Academia. Cofinanciado por el programa de investigación e innovación Horizon Europe de la Unión Europea, en el marco del proyecto NitRecerCat (GA101061189)..
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Synthetic data through combinatorial optimization of pairwise probabilities

  • Salvia Hornos, Josep M.
  • Fernàndez Camon, César
  • Mateu Piñol, Carles
The generation of synthetic data is a critical area of research in domains where real data are either not available in large quantities or cannot be directly used. Different techniques have been developed to produce high-quality, realistic synthetic datasets which retain the statistical properties of the original data. State-of-the-art results focus on the use of neural networks to capture the latent space extracted from the data. While recent advances in the field of deep learning motivate the application in this new context, this paper proposes a naive baseline to generate synthetic data based on pairwise probabilities. We name the technique DISCO (Discrete Intersection Synthesizer through Combinatorial Optimization), a novel synthetic generator for tabular data. DISCO models data by optimizing the intersection of pairwise probabilities on each generated row in order to resemble the original dataset. Our approach preserves marginal (and pairwise) distributions and as a result, resembles the original data with high fidelity with a very simple approach. Evaluation on various synthetic and real-world datasets as well as regression and classification tasks prove DISCO’s ability to generate high-quality data that rivals state-of-the-art models in both statistical accuracy and machine learning efficacy., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. Josep Maria Salvia Hornos reports funding from Generalitat de Catalunya AGAUR DI-2024-00020. Cèsar Fernández reports funding by the Spanish MCIN/AEI/10.130- 39/501100011033/, FEDER, UE in project IDs PID2022-138564OAI00 and PID2022-137971OB-I00. Carles Mateu reports that this work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/ FEDER, UE and RED2022-134219-T).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

A transient heat losses model for two-tank storage systems with molten salts

  • Tagle-Salazar, Pablo D.
  • Prieto, Cristina
  • López-Román, Antón
  • Cabeza, Luisa F.
Concentrating Solar Power (CSP) is a proven and mature technology for energy supply. In recent years, electricity generation based on this technology has increased worldwide, to a large degree due to its high dispatchability when coupled with an energy storage system. Commercially, most plants store the energy in molten salts in a two-tank configuration. This study focuses on this storage configuration and proposes a mathematical model for the thermal losses in these tanks, both at nominal conditions and during transients. With this model at its core, a computational tool for thermal performance analysis in OpenModelica is developed. This dynamic thermal model includes the estimation of local heat loss due to assembly defects, which are heat flows that cannot be determined by theoretical modelling. The development of a semi-empirical correlation for estimating local heat loss is also presented. Simulation results showed that this local heat loss may represent a share about 40% of the total heat loss in a small-scale tank. A comparison of the characteristics of the model proposed in a previous work is also presented to establish the innovation of the model. Two thermal storage systems with different tank designs and sizes were simulated to compare the results using the present model with data available in the literature. Results show good agreement in transient thermal behaviour of heat flows, temperatures, and cooling rates when compared with data from other authors for the same tank., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 838311 (CSP plus). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU, TED2021-132216A-I00 and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Molten salts tanks thermal energy storage: aspects to consider during design

  • Prieto, Cristina
  • Blindu, Adrian
  • Cabeza, Luisa F.
  • Valverde, Juan
  • García, Guillermo
Concentrating solar power plants use sensible thermal energy storage, a mature technology based on molten salts, due to the high storage efficiency (up to 99%). Both parabolic trough collectors and the central receiver system for concentrating solar power technologies use molten salts tanks, either in direct storage systems or in indirect ones. But even though this is a mature technology, it still shows challenges in its implementation and operation. This paper underscores the critical importance of stringent design criteria for molten salt tanks in thermal storage technology. Focusing on the potential ramifications of design failures, the study explores various dimensions where an inadequate design can lead to severe consequences, even jeopardizing the viability of the entire technology. Key areas discussed include structural integrity, corrosion, thermal shock, thermal expansions, and others. By elucidating the multifaceted risks associated with design shortcomings, this paper aims to emphasize the necessity of thorough reviews and adherence to robust design principles for ensuring the success, safety, and sustainability of thermal storage technology., This work was partially funded by the Ministerio de Ciencia e Innovación de España [(PID2021-123511OB-C31—MCIU/AEI/FEDER, UE) (TED2021-132216A-I00) (RED2022-134219-T)].
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Progress and prospects of cold thermal energy storage for liquid air energy storage systems - A critical review

  • Tafone, Alessio
  • Borri, Emiliano
  • Cabeza, Luisa F.
  • O'Callaghan, Odhran
  • Donnellan, Philip
  • Mashayekh, Afshin
  • Kothari, Rohit
  • Haglind, Fredrik
  • Li, Dacheng
  • Xu, Lejin
  • Ding, Yulong
  • Li, Yongliang
  • Yang, Lizhong
  • Romagnoli, Alessandro
  • Dzido, Aleksandra
  • Krawczyk, Piotr
Electrical energy storage plays a vital role in enabling renewable energy integration and achieving decarbonization targets under the Paris Agreement. Liquid air energy storage (LAES) is a promising large-scale, longduration storage technology due to its scalability, site flexibility, and high energy density. A crucial component of LAES performance is the cold thermal energy storage (CTES), which recovers cryogenic exergy during air regasification to recovery during the liquefaction phase, significantly improving the round trip efficiency. This paper presents a comprehensive and critical review of CTES technologies for LAES, aiming to identify optimal design approaches based on current literature and industrial practices. The review covers sensible and latent heat storage systems, hybrid and cascade configurations, and advanced geometries, assessed through thermodynamic and techno-economic performance indicators. Our analysis finds that packed beds with sensible heat materials are the most mature and cost-effective option, while phase change material-based systems offer higher efficiency potential-achieving round-trip efficiency improvements of up to 55 %-but face challenges in material cost, availability, and scalability. Hybrid and cascade configurations show promise in simulations, though experimental data remain limited. Cold storage losses are shown to impact round-trip efficiency up to seven times more than heat losses, highlighting the strategic importance of CTES optimization. The authors identify key research needs in dynamic system modeling, scalable material development, and lifecycle techno-economic assessment. Addressing these gaps will be critical to advancing CTES as a performance-enhancing and cost-effective component of next-generation LAES systems.
Repositori Obert UdL
Publicación Capítulo o parte de un libro (BookPart)

Buildings (< 50 kWh/day). Integrated Batteries with Phase Change Materials (PCM) for Peak Shaving and Load Management: The HYBUILD Example

  • Frazzica, Andrea
  • Valeria , Palomba
  • Aloisio, Davide
  • Zsembinszki, Gabriel
  • Ferraro, Marco
  • Sergi, Francesco
  • Cabeza, Luisa F.
The continuous increasing of renewable-based energy systems, both for heating and power generation, at building level requires the development of innova-tive compact hybrid energy storages. These technologies are able to support the flex-ible operation of such complex systems, increasing the exploitability of renewables and the overall system efficiency. In this chapter, a brief overview of different storage technologies, such as thermal, electric and hybrid, at building level is provided, mostly focusing on their integration with onsite renewable generation and smart grids. The analysis highlights the relevant role of flexible energy storages at building level as well as the lack of innovative components able to provide multiple services (e.g. heating, cooling, domestic hot water and power) to buildings. In such a back-ground, the experience carried out in the framework of the EU-funded HYBUILD project is described. The overall concept, integrating electric batteries, latent, and thermochemical storages, with highly efficient reversible heat pumps is described, showing the different options developed for continental and mediterranean climates. The fully integrated Mediterranean system, validated both at lab-scale and in a demo building, demonstrated the ability of increasing the share of renewables in buildings, maximizing the self-consumption and increasing the overall energy efficiency of the system., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 768824 (HYBUILD). This work was partially funded by the Ministerio de Ciencia, Innovación y Universidades de España (RTI2018-093849-B-C31–MCIU/AEI/FEDER, UE) and the Ministerio de Ciencia e Inno-vación (PID2021-123511OB-C31—MCIN/AEI/https://doi.org/10.13039/501100011033/FEDER, UE) and by the Ministerio de Ciencia, Innovación y Universidades–Agencia Estatal de Investi-gación (AEI) (RED2018-102431-T and RED2022-134219-T). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537 and 2022 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Disseny d'un procés de producció continu de precursors de materials de canvi de fase (PCM) a partir de residus procedents de la indústria agroalimentària

  • Font Prieur, Daylen Yara
El projecte té com a objectiu obtenir materials de canvi de fase (PCM) a través de la producció de l'àcid 9,10-dihidroxiesteàric (DHSA). El procés inclou diverses etapes, pretenent l'extracció eficient dels àcids grassos insaturats a partir de greixos biològics no comestibles procedents de la indústria agroalimentària, per ser utilitzats com a PCM en l'emmagatzematge d'energia tèrmica. L'obtenció d'àcids i èsters són una proposta atractiva per a la indústria a causa del creixent interès i demanda, tant de productes fàcilment degradables per al medi ambient, com de substituts en síntesi orgàniques. El DHSA és un component valuós com a precursor de PCM a causa de les seves propietats termodinàmiques. Els PCM són materials útils com l'emmagatzematge d'energia tèrmica, susceptibles de tenir aplicacions a l'àmbit, per exemple, de la construcció. El procés inclou l'ús de substàncies químiques inflamables o explosives, cosa que en compromet l'escalat. Aquest projecte s'orienta a la producció a escala de PCM de manera segura a partir de biomassa no comestible., Aquest treball està parcialment finançat pel Ministeri de Ciència i Innovació - Agència Estatal de Recerca (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) i el Ministeri de Ciència, Innovació Estatal de Recerca (AEI) (RED2022-134219-T). ). Els autors agraeixen a la Generalitat de Catalunya l’acreditació de qualitat concedida al grup de recerca GREiA (2021 SGR 01615). GREiA és un agent certificat TECNIO en la categoria de desenvolupadors tecnològics de la Generalitat de Catalunya. Aquest treball està parcialment secundat per ICREA dins del programa ICREA Academia. Aquest projecte está cofinançat pel programa de recerca i innovació de la Unió Europea Horizon Europe, en el marc del projecte NitRecercat2425 (101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Formulation and development of composite materials for thermally driven and storage‑integrated cooling technologies: a review

  • Borri, Emiliano
  • Ushak, Svetlana
  • Li, Yongliang
  • Frazzica, Andrea
  • Zhang, Yannan
  • Milian, Yanio
  • Grageda, Mario
  • Li, Dacheng
  • Cabeza, Luisa F.
  • Brancato, Vincenza
The energy consumption for cooling takes up 50% of all the consumed final energy in Europe, which still highly depends on the utilization of fossil fuels. Thus, it is required to propose and develop new technologies for cooling driven by renewable energy. Also, thermal energy storage is an emerging technology to relocate intermittent low-grade heat source, like solar thermal energy and industrial waste heat as well as to exploit off-peak electricity, for cooling applications. This review aims to summarize the recent advances in thermally driven cooling and cold storage technologies, focusing on the formation and fabrication of adopted composites materials, including sorption materials, phase change materials, and slurries. Herein, first the classifications, selection criteria, and properties for these three types of materials is discussed. Then, the application potentials of all the materials are prospected in terms of economic analysis and sustainability., Acknowledgements The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certifed agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme. This project has received funding from ThumbsUp (Thermal energy storage solUtions to optimally Manage BuildingS and Unlock their grid balancing and fexibility Potential). ThumbsUP is a Horizon Europe Project supported by the European Commission under contract No. 101096921. Funding This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement CO-COOL (101007976). Authors acknowledge to ANID/ PUENTE No 1522A0006 and ANID/FONDECYT REGULAR No 1231721 projects. This work was partially funded by the Ministerio de Ciencia e Innovación de España [(PID2021-123511OB-C31— MCIU/AEI/FEDER, UE) (RED2022-134219-T)]. The authors at the University of Birmingham gratefully acknowledge the fnancial supports from the Engineering and Physical Sciences Research Council (EPSRC) of the UK (EP/T022701/1). Data availability Data is available und
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Transient performance modelling of solar tower power plants with molten salt thermal energy storage systems

  • Tagle-Salazar, Pablo D.
  • Cabeza, Luisa F.
  • Prieto, Cristina
Concentrating solar power (CSP) has emerged as a dynamic and promising technology, demonstrating a burgeoning market potential for power generation through the utilization of solar thermal resources. Notably, global installed capacity has witnessed a substantial uptick in recent years, indicative that this technology is increasing traction worldwide. To optimize the utilization of CSP systems, particularly during periods of low or absent solar radiation, the integration of thermal energy storage (TES) systems using molten salts has become a prevailing strategy. This research introduces an innovative transient modelling tailored for the comprehensive annual performance analysis of a solar tower power plant coupled to a two-tank TES system, incorporating molten salts as the storage medium. The modelling of the power plant is conducted using OpenModelica, a versatile software platform renowned for its capability in system-level modelling and simulation. The simulation outcomes encompass a power plant configuration boasting a turbine gross output of 110 MWe. The results of performance parameters are subsequently contrasted with those generated by commercially available software tool, effectively corroborating the accuracy and effectiveness of the proposed simulation approach. The obtained results demonstrate a favourable concurrence in the transient behaviour of performance parameters, considering heat flows, state of charge, net power, and others, with a discrepancy of less than 1 % in annual production when benchmarked against a commercial software reference. Particularly, the incorporation of the local heat loss due to assembly defects within the thermal modelling of the TES system exerts a discernible albeit relatively minor influence on the overall performance of the power plant. The occurrence of local heat loss primarily stems from distortions or imperfections within the construction, including the structure, insulation layers, or foundation, thereby creating thermal bridges between the storage fluid and the external ambient environment. This impact, while small, is not negligible, as it introduces the potential for the power block to unexpectedly shut down owing to TES system depletion, a behaviour that is challenging to simulate when neglecting local heat loss., CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This study receives funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/“PRTR”. This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Phase change materials for thermal energy storage in industrial applications

  • Martínez, Franklin R.
  • Borri, Emiliano
  • Mani Kala, Saranprabhu
  • Ushak, Svetlana
  • Cabeza, Luisa F.
This study reports the results of the screening process done to identify viable phase change materials (PCMs) to be integrated in applications in two different temperature ranges: 60–80 °C for mid-temperature applications and 150–250 °C for high-temperature applications. The comprehensive review involved an extensive analysis of scientific literature and commercial material datasheets. A total of 65 PCMs for mid-temperature applications and 36 PCMs for high-temperature applications were identified through this extensive search. Moreover, an extensive experimental characterization of 14 preselected PCMs is included. Experimental techniques including differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and hot disk were used. The values obtained were compared to the ones found in the available literature and technical datasheets to see potential differences in the thermal behavior., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101103552 (SUSHEAT). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovacion´ - Agencia Estatal de Investigacion´ (AEI) (PID2021-123511OB-C31 - MCIN/ AEI/10.13039/501100011033/FEDER, UE), and Ministerio de Ciencia e Innovacion´ - Agencia Estatal de Investigacion´ (AEI) (RED2022-134219-T). S. Ushak acknowledges to ANID/PUENTE Nº 1522A0006 and ANID/FONDECYT REGULAR Nº 1231721 projects. This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Optimizing the design of TES tanks for thermal energy storage applications an integrated biomimetic-genetic algorithm approach

  • Mehraj, Nadiya
  • Mateu Piñol, Carles
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Building upon an experimentally validated bio-inspired thermal energy storage (TES) tank design, this study introduced a novel computational framework that integrated genetic algorithms (GA) with biomimetic principles to systematically generate TES tank geometries. Inspired by natural thermal distribution patterns found in vascular networks, the AI-driven methodology explored 13 geometric parameters, focusing on branching structures and spatial distribution, and resulted in computationally generated designs with a 29% increase in heat transfer surface area while maintaining manufacturability constraints within a fixed tank diameter of 150 mm and height of 155 mm. Unlike previous biomimetic TES studies that relied on predefined geometric configurations, this approach developed AI-driven bio-inspired structures within experimentally validated dimensional constraints, ensuring geometric relevance while allowing for broader structural exploration. The resulting designs exhibited key characteristics of high-efficiency bio-inspired configurations while providing a systematic, scalable methodology for TES tank architecture. This study represented the first step in integrating AI-driven biomimicry into TES tank design, establishing a structured framework for generating high-performance, manufacturable configurations. While the current work focused on computational design, future research will emphasize experimental validation and real-world implementation to confirm the practical thermal and structural benefits of these AI-generated bio-inspired designs. By bridging the gap between computational intelligence and nature-inspired engineering, this research provided a scalable pathway for developing more efficient, manufacturable, and sustainable TES solutions for energy storage applications., Funding: This study has received funding from the European Union’s Horizon Europe Research and Innovation Programme under grant agreement No. 101103552 (SUSHEAT). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was also partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI)—NextGeneration EU (TED2021-129462BI00— MCIN/AEI/10.13039/501100011033/ NextGenerationEU/PRTR, PID2021-123511OB-C31— MCIN/AEI/10.13039/501100011033/FEDER, UE, and RED2022-134219-T). Acknowledgments: This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental investigation of mono and hybrid GNP − MWCNT nano-enhanced phase change materials for thermal energy storage applications

  • Güngör, Sercan Gülce
  • Martínez, Franklin R.
  • Borri, Emiliano
  • Gasa, Gemma
  • Esen, Mehmet
  • Cabeza, Luisa F.
This study aims to examine the effect of carbon-based nanoparticles of different sizes and morphologies, which are 2D graphene nanoplatelets (GNPs) and 1D multi-walled carbon nanotubes (MWCNTs). These are used in mono and hybrid forms to investigate the thermal properties of n-octadecane, an organic phase change material. The thermal conductivity, latent heat, and phase change temperature of nano-enhanced phase change material (NePCM) samples are analyzed at different concentrations ranging from 0 to 2.5% by weight. Improvements in thermal conductivity values are 22.3% and 52.3% when MWCNT and GNP are added separately, respectively, and 39.6% when adding the hybrid of GNP and MWCNT is added. Reductions in latent heat values are 5.8% and 5.7% when MWCNT and GNP are used separately and 6.6% when GNP + MWCNT are used together. The experimental measurement values are evaluated using statistical analysis and multi-objective optimization. According to the results, this optimization process identifies the most suitable NePCM sample., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021- 123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia Programme. The authors from University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This study was partially supported by the Scientific Research Projects Coordination Unit of Firat University. Project number: TEKF.25.58. The authors from Firat University would like to thank the Scientific Research Projects Coordination Unit of Firat University.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Diseño de tanques de almacenamiento de energía termica (TES) mediante el uso de redes neuronales e inteligencia artificial

  • Rojas Cala, Edgar Felipe
Los tanques de almacenamiento de energía térmica son depósitos que permiten almacenar energía térmica para ser usada después de mucho tiempo; esto, gracias al uso de diferentes materiales y diseños que permiten absorber, almacenar yliberar esta energía, Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) y el Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen al Gobierno de Cataluña la acreditación de calidad concedida al grupo de investigación GREiA (2021SGR01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos del Gobierno de Cataluña. Este trabajo está parcialmente apoyado por ICREA dentro del programa ICREA Academia. El proyecto NitRecercaCat (GA 101061189) está cofinanciado por el programa de investigación e innovación Horizonte Europa de la Unión Europea.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental and computational assessment of building structures reinforced with textile fiber waste to improve thermo-mechanical performance

  • Ayed, Rabeb
  • Borri, Emiliano
  • Skouri, Safa
  • Lachheb, Mohamed
  • Bouadila, Salwa
  • Younsi, Zohir
  • Cabeza, Luisa F.
  • Lazaar, Mariem
Faced with the growing demand for energy-efficient construction and the need to address environmental challenges, the building sector must innovate to reduce energy consumption and promote sustainability. This study investigates a dual solution to these challenges by enhancing the thermo-mechanical performance of building materials through the integration of textile fiber waste, using a combination of experimental and computational methodologies. This investigation focused on incorporating textile fiber wastes in cementitious composites for construction applications. A series of mechanical and thermal tests were carried out on the cement mortars with different proportions of incorporated textile fibers after 7 and 28 days of water curing. The results showed that the incorporation of fibers can significantly improve the thermal insulation of buildings by reducing the thermal conductivity of cement mortar by up to 52%. To complement experimental findings, computational models were developed using COMSOL Multiphysics 6.2 software to predict the thermal diffusivity and volumetric heat capacity of textile-reinforced mortars. These models revealed that mortars incorporating 40% textile fibers as a sand replacement achieved significant reductions in thermal conductivity, thermal diffusivity, and volumetric heat capacity by approximately 40%, 21%, and 23%, respectively, compared with ordinary cement mortar. Furthermore, this study numerically examined the potential of combining textile-reinforced mortar with phase-change material (PCM) in building applications. The aim of the research was to overcome the challenges of cooling buildings in scorching summer conditions. The optimization of roof and wall composition was based on an assessment of air temperature variation within a space., Funding This study was supported by the Thermal Processes Laboratory of the Research and Technology Center of Energy (CRTEn) and the University of Tunis El Manar in Tunisia. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This publication is based upon work from COST Action CircularB, supported by COST (European Cooperation in Science and Technology). This work is partially supported by ICREA under the ICREA Academia programme. Acknowledgments The authors from GREiA Research Group would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme. This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Heat transfer enhancement of thermal energy storage systems using phase change materials: experimental work

  • Megra, Kassahun Tadesse
Growing energy demand and environmental concerns are accelerating the shift to renewable sources. Solar and other renewables need efficient storage due to their intermittent nature. TES systems using phase change materials (PCMs) are promising for storing heat at constant temperatures. This research enhances TES performance by optimizing heat transfer and evaluating PCMs under real conditions. The results aim to support efficient and sustainable integration of renewable energy., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement HYBRIDplus (101084182) and SUNSHINE (101103552). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This paper is part of the RYC2023-044196, funded by MCIN/AEI/10.13039/501100011033 and FSE+, and Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/501100011033/FEDER, UE). This work is also partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is a certified TECNIO agent in the category of technology developers of the Government of Catalonia. This project is also co-funded by the European Union’s research and innovation programme Horizon Europe under the project NitRecercat2425 (GA 101162003).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental evaluation of a hybrid electrical and thermal energy storage system in a pilot residential house during summer conditions in a Mediterranean climate

  • Zsembinszki, Gabriel
  • Vérez, David
  • Cabeza, Luisa F.
The integration of various types of renewable energy sources, coupled with the implementation of energy storage systems, can enhance solar energy utilisation and reduce primary energy consumption in buildings. This paper focuses on experimentally assessing the effectiveness of an innovative hybrid electric/thermal system designed to provide cooling, heating, and domestic hot water (DHW) services for single-family houses in Mediterranean climate regions. Specifically, the system integrates a sorption chiller coupled with a heat pump and a hybrid electric/thermal energy storage system to enhance overall system efficiency. It includes Fresnel solar collectors and photovoltaic panels to reduce the reliance on primary energy derived from fossil fuels. Experimental testing was conducted at a pilot house located in Spain over one representative week in the summer. The results were assessed based on various key performance indicators (KPIs), including the thermal energy efficiency ratio and performance ratio, electric selfconsumption, self-sufficiency, and share of renewables, among others. The sorption chiller exhibited a relatively low thermal efficiency ratio of 0.35 and a higher thermal performance factor of 1.88, indicating limited use of this component. Positive outcomes were obtained for selfconsumption, self-sufficiency, and share of renewables, which attained a weekly average of 0.80, 0.50, and 0.67, respectively., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 768824 (HYBUILD). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU; and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank all the persons that contributed to the design and development of the installation evaluated in this paper.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental characterization of phase change materials for thermal energy storage in the temperature range between 270 °C and 400 °C

  • Martínez, Franklin R.
  • Borri, Emiliano
  • Ushak, Svetlana
  • Mani Kala, Saranprabhu
  • Prieto, Cristina
  • Cabeza, Luisa F.
Thermal energy storage (TES) with phase change materials (PCM) is an interesting technology to be used to improve the energy efficiency of industrial processes, contributing to their decarbonization and the integration of renewable energy sources. Even though literature lists many materials that can be used as PCM in the temperature range between 270 °C and 400 °C, most of them lack a full characterisation, jeopardising their potential implementation by practitioners and scientists. Therefore, this paper presents a complete experimental characterisation of 24 PCMs, with melting temperature, melting enthalpy, degradation temperature, and thermal conductivity in the solid state (at room temperature) determination. Moreover, corrosion tests with two different stainless-steel fibres and with Alloy 20 fibres is presented. The findings obtained in the characterization highlight the necessity of these analyses, as notable differences were observed compared to the available data, particularly in thermal stability and thermal conductivity. Moreover, the findings obtained in the compatibility test reveals that out of the 24 selected PCMs, 11 are potentially compatible with Alloy 20, and 8 with both stainless-steel fibres under environmental conditions (air atmosphere). Finally, the results presented will allow researchers and practitioners to have very detailed data on the characterisation of those PCMs., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovacion´ - Agencia Estatal de Investigacion´ (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/ 501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N◦ 1523A0006 and ANID/FONDECYT REGULAR N◦ 1231721 projects
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploring the role of surface roughness in concrete-based thermal energy storage systems: A computational study

  • Rahjoo, Mohammad
  • Rojas, Esther
  • Goracci, Guido
  • Dolado, Jorge S.
This study computationally investigates the effect of thermal energy storage (TES) material surface roughness on heat transfer fluid (HTF) flow dynamics and heat transfer capabilities. The motivation is to further understand systems where concrete as the TES material directly interfaces with air as the HTF, based on previous research suggesting potential benefits of avoiding differential thermal expansion issues associated with metallic tubes. A k-ε turbulence model in COMSOL Multiphysics examined air flow over concrete surfaces with five levels of roughness from 0 to 3 mm peak height. Increasing surface roughness enhances turbulence and significantly improves heat transfer and thermal storage performance, with 7 % higher charging efficiency and energy storage capacity and 55.6 % greater heat transfer rate from 0.3 to 3 mm roughness, despite a 138 % increase in pressure drop. Applying artificial surface modifications like indentations or fins could further optimize efficiency by amplifying heat transfer advantages of increased roughness while moderating pressure losses. This indicates a promising direction for future research on enhancing thermal energy storage through concrete surface optimization and substantiates the potential of concrete as an inexpensive, scalable, high performance TES material., This work was born under the umbrella of the project “Energy storage solutions based on concrete (E-CRETE)” (RTI2018-098554-B-I00) funded by MCIN/AEI/10.13039/501100011033 (Program I+D+i RETOS INVESTIGACIÓN 2018) and PCTE (PID2022-137845NB-C22) funded by MCIN/AEI/10.13039/501100011033. Mohammad Rahjoo acknowledges the grant PRE2019-087676 funded by MCIN/AEI/10.13039/501100011033 and co-financed by the European Social Fund under the 2019 call for grants for predoctoral contracts for the training of doctors contemplated in the State Training Subprogram of the State Program for the Promotion of Talent and its Employability in R&D&I, within the framework of the State Plan for Scientific and Technical Research and Innovation 2017–2020. In addition, the economic support from POVAZSKA is acknowledged. Jorge S. Dolado acknowledges the funding from the Gobierno Vasco UPV/EHU (project no. IT1569-22). This work is partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biomass Ash and Phase Change Material (PCM) for Energy Efficiency of Sustainable Cement–Lime Composites

  • Guardia, Cynthia
  • Guerrero Bustos, Ana María
  • Barluenga, Gonzalo
This article belongs to the Special Issue Advances in Research on Phase Change Materials for Thermal Energy Storage Applications, Sustainability and nearly zero-energy consumption of new and existing buildings is a keystone in the new guidelines established by the European Commission. Likewise, waste management is in the focus of reducing the impact of industrial processes. The use of industrial byproducts, such as biomass ashes (BA), can be an interesting solution for waste valorization, reducing the carbon footprint and enhancing sustainability. In addition, Phase Change Materials (PCMs) can be used for improving energy efficiency due to their thermal storage capacity. An experimental study on the effect of biomass ash (BA) and PCM on the microstructure, chemical, physical and mechanical properties of cement–lime pastes was carried out. The partial replacement of cement with BA reduced compressive strength although did not substantially modify other paste properties, while the addition of PCM had a huge impact on microstructure and, therefore, physical and mechanical properties. PCM had a remarkable effect on thermal properties, endowing thermal storage capacity and reducing thermal conductivity, and the combination with BA further improved paste thermal properties., The authors acknowledge the financial support provided by the University of Alcalá (Spain), the Spanish Ministry of Universities and the European Union “Next Generation EU”—Margarita Salas Grant, awarded to Dr. Cynthia Guardia and the project CALTH3D (TED2021-132585B-I00) and RED2022-134219-T, funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033). The authors gratefully acknowledge the financial support from the European Commission through the Marie Skłodowska-Curie Actions (MSCA) under Grant Agreement ID: 101086440, BEST—Bio-based Energy-efficient Materials and Structures for Tomorrow project (https://doi.org/10.3030/101086440)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Macroencapsulated phase change material assessment for envelope applications: effect of low temperature variation rates and actual size

  • Alvarez-Rodriguez, Matias
  • Alonso-Martínez, Mar
  • Coz Diaz, Juan José del
  • Espina, Aránzazu
  • García-Granda, Santiago
Data will be made available on request., Traditional PCM characterization methods analyze small samples of PCM alone using high temperature variation rates. However, previous studies concluded that the thermal properties of the PCMs alone and the macroencapsulated PCMs differ. As such, there is a lack of research into the characterization of whole PCM macrocapsules at low temperature variation rates. This work presents a novel experimental method to characterize macroencapsulated PCMs for building envelopes based on evaluating the thermal response of whole PCM macrocapsules: PCM, capsule material, and air gap. Two temperature variation rates were used: 0.5 °C/h and 1 °C/h, typical of building envelope applications. This methodology determines the latent heat, phase change temperature range, and peak phase change temperature of whole PCM macrocapsules. Four commercial macroencapsulated PCMs were subjected to the developed methodology. Consistency in the experimental results across multiple tests demonstrates the reliability of the proposed procedure. The results reveal that the temperature variation rate and phase change process significantly affect the thermal response of macroencapsulated PCMs. At lower rates (0.5 °C/h), the phase change temperature ranges were narrower, with differences in range amplitude of up to 2 °C between melting and solidification. Additionally, latent heat values in the macroencapsulated PCMs were consistently lower than the values specified by the manufacturer for the PCM alone (up to 57.78 % lower). This highlights both the influence of the PCM mass and the whole macrocapsule's effect. The phase change properties of a macroencapsulated PCM were compared with the values obtained through differential scanning calorimetry (DSC) on PCM alone. The experimental results demonstrate that, although DSC accurately characterizes PCMs, it overestimates the thermal energy storage capacity of whole macroencapsulated PCMs. Phase change temperature ranges obtained under realistic temperature variation rates in building envelopes are narrower than in traditional DSC tests at higher rates. These findings underscore the need for specific experimental characterization of macroencapsulated PCMs for building applications, contributing to improved energy efficiency and thermal comfort in buildings. Our methodology can be applied to any other macroencapsulated PCM, being a powerful tool to bridge the gap between the thermal behavior of macroencapsulated PCM and PCM alone., The authors greatly appreciate the collaboration of the GICONSIME and SYSTAM Research Groups at the University of Oviedo. Furthermore, this work was supported by the Spain's Ministry of Universities (FPU21/05062) and Spain's Ministry of Science and Innovation and through Research Projects PID2021-128056OA-I00, PID2020-113558RB-C41, TED2021-131976B-I00 and RED2022-134219-T; and Foundation for the Promotion in Asturias of Applied Scientific Research and Technology through project SV-PA-21-AYUD 2021 51328., Peer reviewed
Repositorio Institucional de la Universidad de Burgos (RIUBU)
Publicación Tesis doctoral (DoctoralThesis)

Investigación sobre el equilibrio de fases de nuevos materiales y fluidos renovables para usos energéticos mediante técnicas experimentales

  • Rubio Pérez, Gabriel
La creación de sistemas de gestión y generación energética más sostenibles sigue siendo una prioridad tanto a nivel europeo como internacional, tal y como muestran proyectos como el Horizonte Europa, los Objetivos de Desarrollo Sostenible (ODS) o las iniciativas de la Agencia Internacional de Energía (IEA). Si bien las energías renovables obstentan un papel central en esta transición energética, otras técnicas complementarias están siendo también desarrolladas para compensar algunas de sus desventajas, como el suministro intermitente o el desacoplo entre generación y consumo de energía. Así, el almacenamiento de energía adquiere un matiz indispensable, incluyendo el almacenamiento de energía térmica (TES). En concreto, el almacenamiento de energía térmica mediante materiales de cambio de fase (PCM) concentra parte de la atención de la comunidad científica por su gran potencial y versatilidad. En la presente Tesis se cubren las principales metodologías experimentales empleadas en el estudio y la creación de los PCM, incluyendo resultados experimentales para respaldar su validez., The creation of more sustainable energy generation and management systems remains a priority at both European and international levels, as shown by projects such as Horizon Europe, the Sustainable Development Goals (SDGs) or the initiatives of the International Energy Agency (IEA). While renewable energies hold a key role in this energy transition, other complementary techniques are also being developed to compensate for some of their disadvantages, such as intermitent supply or the decoupling of energy generation and consumption. Thus, energy storage becomes indispensable, including Thermal Energy Storage (TES). Thermal energy storage by means of Phase Change Materials (PCM) is particularly receiving a great deal of atention from the scientific community due to its great potential and versatility. The present Thesis covers the main experimental methodologies employed in the study and creation of PCMs, including experimental results to support their validity., El desarrollo de esta Tesis se enmarca en las actividades realizadas por la Red Española de Almacenamiento de Energía Térmica (RedTES), que ha sido financiada de nuevo recientemente para los próximos años (ayuda RED2022-134219-T) por la Agencia Estatal de Investigación mediante las ayudas 2022 a “Redes de Investigación” en el marco del Programa Estatal para Impulsar la Investigación Cientifico-Técnica y su Transferencia, del Plan Estatal de Investigación Cientifica, Técnica y de Innovación 2021-2023. Quiero agradecer profundamente a la RedTES toda la ayuda que me han brindado sus miembros, tanto material como humana, sin la cual el desarrollo de esta Tesis no habría sido posible. También quiero agradecer al Ministerio de Ciencia, Innovación y Universidades la financiación obtenida estos años mediante una beca de Formación del Profesorado Universitario (FPU), convocatoria 2018, que me ha permitido llevar a cabo todo el trabajo realizado estos años.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A transient heat losses model for two-tank storage systems with molten salts

  • Tagle-Salazar, Pablo D.
  • Prieto, Cristina
  • López-Román, Antón
  • Cabeza, Luisa F.
Concentrating Solar Power (CSP) is a proven and mature technology for energy supply. In recent years, electricity generation based on this technology has increased worldwide, to a large degree due to its high dispatchability when coupled with an energy storage system. Commercially, most plants store the energy in molten salts in a two-tank configuration. This study focuses on this storage configuration and proposes a mathematical model for the thermal losses in these tanks, both at nominal conditions and during transients. With this model at its core, a computational tool for thermal performance analysis in OpenModelica is developed. This dynamic thermal model includes the estimation of local heat loss due to assembly defects, which are heat flows that cannot be determined by theoretical modelling. The development of a semi-empirical correlation for estimating local heat loss is also presented. Simulation results showed that this local heat loss may represent a share about 40% of the total heat loss in a small-scale tank. A comparison of the characteristics of the model proposed in a previous work is also presented to establish the innovation of the model. Two thermal storage systems with different tank designs and sizes were simulated to compare the results using the present model with data available in the literature. Results show good agreement in transient thermal behaviour of heat flows, temperatures, and cooling rates when compared with data from other authors for the same tank., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 838311 (CSP plus). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU, TED2021-132216A-I00 and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal energy storage for direct steam generation concentrating solar power plants: Concept and materials selection

  • Prieto, Cristina
  • Cabeza, Luisa F.
  • Pavón Moreno, M. Carmen
  • Palomo, Elena
Direct steam generation (DSG) concentrating solar power (CSP) plants uses water as heat transfer fluid, and it is a technology available today. It has many advantages, but its deployment is limited due to the lack of an adequate long-term thermal energy storage (TES) system. This paper presents a new TES concept for DSG CSP plants. This system is based on three blocks, a saturated block based on phase change materials, an overheating block that elevates the vapor temperature of a heat transfer fluid to the desired values, and a preheating block that increases the temperature difference between a cold tank and a hot tank of a non-phase change thermal storage material. After a deep selection and characterization process, the material to be used is LiOH/KOH, since although it has the disadvantage of high corrosion, the identified advantages overcome it as an ideal PCM for this process., This work was partially funded by the Ministerio de Ciencia e Innovacion ´ de Espana ˜ [(TED2021-132216A-I00) (ITC-20111061- FEDER-Innterconecta-Composol), (PID2021-123511OB-C31 - MCIU/ AEI/FEDER, UE), and (RED2022-134219-T)]. The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2017 SGR 1537). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Failure analysis of the leakage and ignition of heat transfer fluid in a concentrating solar power (CSP) pilot plant

  • Prieto, Cristina
  • López-Román, Antón
  • Cabeza, Luisa F.
Concentrating solar power (CSP) is a technology seen key to achieve the worldwide energy transition targets. Although it is a mature robust technology, different failures in CSP plant have been reported in the literature to visualize potential point of maintenance interest. Following the same philosophy, this paper reports a failure occurred at a CSP storage pilot plant, where leakage and ignition of different joint balls suddenly occurred after several hours of testing. The experimental assessment carried out confirmed spontaneous ignition of the heat transfer fluid-soaked insulation material of the piping after leakage. The results of this study emphasize the significance of proactive maintenance and daily inspections in solar fields., This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación de España (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 1615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

AI-aided design of high-performance thermal energy storage systems inspired by nature (Nit Europea de la Recerca 2024)

  • Mehraj, Nadiya
Renewable energy communities (REC) represent a pivotal paradigm shift in energy management, emphasizing collective action and shared resources to address environmental challenges by enabling members to pool their renewable energy resources and distribute surplus energy where it is needed most. Through collaboration and energy sharing, these communities not only reduce reliance on fossil fuels but also promote local resilience and autonomy in energy production. Thermal energy storage systems could play an important role in maximizing the effectiveness of renewable energy sharing and consumption within communities. They efficiently store excess renewable energy, ensuring its availability when needed most, thereby enhancing the reliability and stability of local energy networks while minimizing wastage., This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-12351108-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU), and by Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This project is co-funded by the European Union's research and innovation programme Horizon Europe under the project NtRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Phase change materials for thermal energy storage in industrial applications

  • Martínez, Franklin R.
  • Borri, Emiliano
  • Mani Kala, Saranprabhu
  • Ushak, Svetlana
  • Cabeza, Luisa F.
This study reports the results of the screening process done to identify viable phase change materials (PCMs) to be integrated in applications in two different temperature ranges: 60–80 °C for mid-temperature applications and 150–250 °C for high-temperature applications. The comprehensive review involved an extensive analysis of scientific literature and commercial material datasheets. A total of 65 PCMs for mid-temperature applications and 36 PCMs for high-temperature applications were identified through this extensive search. Moreover, an extensive experimental characterization of 14 preselected PCMs is included. Experimental techniques including differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and hot disk were used. The values obtained were compared to the ones found in the available literature and technical datasheets to see potential differences in the thermal behavior., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101103552 (SUSHEAT). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovacion´ - Agencia Estatal de Investigacion´ (AEI) (PID2021-123511OB-C31 - MCIN/ AEI/10.13039/501100011033/FEDER, UE), and Ministerio de Ciencia e Innovacion´ - Agencia Estatal de Investigacion´ (AEI) (RED2022-134219-T). S. Ushak acknowledges to ANID/PUENTE Nº 1522A0006 and ANID/FONDECYT REGULAR Nº 1231721 projects. This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Analysis on integration of heat pumps and thermal energy storage in current energy system: From research outputs to energy policies

  • Rehman, Omais Abdur
  • Borri, Emiliano
  • Palomba, Valeria
  • Frazzica, Andrea
  • Brancato, Vincenza
  • Botargues, Teresa
  • Cabeza, Luisa F.
This paper presents a comprehensive examination of the integration of heat pumps and thermal energy storage (TES) within the current energy system. Utilizing bibliometric analysis, recent research trends and gaps are identified, shedding light on the evolving landscape of this dynamic field. The study delves into the research outputs since 1969, offering insights into the global scholarly contributions shaping the discourse. Furthermore, an extensive policy analysis is conducted, focusing on seven countries with the highest research output. The interplay between research advancements and energy policies is explored, providing an understanding of the practical implications of the integration of heat pumps and TES. An understanding is tried to reach as how research and policy sector influence each other. This analysis contributes not only to the academic understanding of the subject but also informs policymakers about potential pathways for enhancing energy efficiency and sustainability in heating and cooling sector., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 101007976 (CO-COOL). This work is partially supported by ICREA under the ICREA Academia programme. This work is also partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal Properties and Pore Structure of Electric Arc Furnace Slag Mortars for Solar-Exposed Building Components

  • Sucupira, Luciana
  • Zsembinszki, Gabriel
  • Risco Amigó, Sara
  • Castro-Gomes, João
  • Cabeza, Luisa F.
The valorisation of electric arc furnace (EAF) slag in construction materials can reduce the consumption of virgin raw materials while creating opportunities for CO2 mineralisation. However, the combined influence of EAF slag aggregate, aggregate particle-size range and biochar addition on the mechanical, pore-structure and thermal behaviour of carbonated mortars remains insufficiently understood. This study investigated mortars produced with EAF slag as binder and, in selected formulations, as aggregate, with and without biochar. Three aggregate particle-size ranges were assessed: 0.5–1 mm, 1–2 mm, and 2–4 mm. After static compaction and accelerated carbonation, the mortars were characterised in terms of compressive strength, degree of carbonation, pore structure, thermal conductivity, heat-storage capacity and dynamic thermal response. The 100% EAF slag mixtures achieved the highest carbonation degrees, reaching 32.62% for the 1–2 mm formulation containing biochar. Among the tested mixtures, formulation 3C, consisting of 100% EAF slag without biochar and with a particle-size range of 1–2 mm, showed the most balanced overall performance, with a compressive strength of 17.91 MPa, a carbonation degree of 32.13%, a porosity of 24.01%, a thermal conductivity of 0.804 W m−1 K−1, a specific heat capacity of 884 J kg−1 K−1 and a thermal lag of 1.22 h. Although the thermal lag was limited for the 4 cm-thick specimens, the results indicate potential for carbonated EAF-slag mortars to contribute as functional layers in solar-exposed multilayer building components requiring mechanical integrity and short-term heat storage., This work was supported by FCT—Fundação para a Ciência e Tecnologia, I.P., of Research Unit C-MADE, Centre of Materials and Building Technologies, by project reference UIDB/04082/2020 and DOI identifier <https://doi.org/10.54499/UIDB/04082/2020>. The study also received support from the Marie Skłodowska-Curie Actions “Research and Innovation Staff Exchange (MSCA RISE) program” through the project “CSTO2NE—Biomimicry and carbon adsorbent eco-materials for a climate-neutral economy” (project reference 101086302). The Ministerio de Ciencia e Innovación partially funded this work—Agencia Estatal de Investigación (AEI)—NextGeneration EU (PID2021- 123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Renewable Energy Community Integration: sharing of renewable through thermal energy storage technology

  • Brunelli, Luca
Renewable energy communities (REC) represent a pivotal paradigm shift in energy management, emphasizing collective action and shared resources to address environmental challenges, by enabling members to pool their renewable energy resources, and distribute surplus energy where it is needed most. Through collaboration and energy sharing, these communities not only reduce reliance on fossil fuels but also promote local resilience and autonomy in energy production. Thermal energy storage systems could play an important role in maximizing the effectiveness of renewable energy sharing and consumption. within communities. They efficiently store excess renewable energy, ensuring its availability when needed most, thereby enhancing the reliability and stability of local energy networks while minimizing wastage., This work is partially supported by ICREA under the ICREA Academia programme. The authors would lke to thank the Departament de Recerca | Universitats of the Catalan Government for the quallty accreditation glven to their research. This project is co-funded by the group (2021 SGR 01615). GREA Is certified agent TECNIO In the category of technology developers from the European Union's Govemnment of Cataionia. This work was partully funded by the Ministerio de Ciencla e Innovacidn - Aencla Estatal de Innovation programme Horizon Europe, Investigación (AEI) (PID2021-12351108-C31 - MCIN/AE1/10.13039/501100011033/FEDER, UE), and by Miniterio de Ciencia e Innovación - Agencia Estatal de Investigaoón (AEI) (RED2022-134219-T). This project is co-funded by the European Union’s research and innovation programme Horizon Europe, under the project NtRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental investigation of mono and hybrid GNP − MWCNT nano-enhanced phase change materials for thermal energy storage applications

  • Güngör, Sercan Gülce
  • Martínez, Franklin R.
  • Borri, Emiliano
  • Gasa, Gemma
  • Esen, Mehmet
  • Cabeza, Luisa F.
This study aims to examine the effect of carbon-based nanoparticles of different sizes and morphologies, which are 2D graphene nanoplatelets (GNPs) and 1D multi-walled carbon nanotubes (MWCNTs). These are used in mono and hybrid forms to investigate the thermal properties of n-octadecane, an organic phase change material. The thermal conductivity, latent heat, and phase change temperature of nano-enhanced phase change material (NePCM) samples are analyzed at different concentrations ranging from 0 to 2.5% by weight. Improvements in thermal conductivity values are 22.3% and 52.3% when MWCNT and GNP are added separately, respectively, and 39.6% when adding the hybrid of GNP and MWCNT is added. Reductions in latent heat values are 5.8% and 5.7% when MWCNT and GNP are used separately and 6.6% when GNP + MWCNT are used together. The experimental measurement values are evaluated using statistical analysis and multi-objective optimization. According to the results, this optimization process identifies the most suitable NePCM sample., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021- 123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia Programme. The authors from University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This study was partially supported by the Scientific Research Projects Coordination Unit of Firat University. Project number: TEKF.25.58. The authors from Firat University would like to thank the Scientific Research Projects Coordination Unit of Firat University.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Hardware-in-the-loop tecniques for complex systems analysis: Bibliometric analysis of available literature

  • Cabeza, Luisa F.
  • Vérez, David
  • Teixidó Cairol, Mercè
Simulating complex systems in real time presents both significant advantages and challenges. Hardware-in-the-loop (HIL) simulation has emerged as an interesting technique for addressing these challenges. While HIL has gained attention in the scientific literature, its application in energy studies and power systems remains scattered and challenging to locate. This paper aims to provide an assessment of the penetration of the HIL technique in energy studies and power systems. The analysis of the literature reveals that HIL is predominantly employed in evaluating electrical systems (smart grids, microgrids, wind systems), with limited application in thermal energy systems (energy storage). Notably, the combination of electrical hardware-in-the-loop (EHIL) and thermal hardware-in-the-loop (THIL) techniques has found application in the assessment of vehicle thermal management systems and smart cities and, recently, has also been adopted in building systems. The findings highlight the potential for further exploration and expansion of the HIL technique in diverse energy domains, emphasizing the need for addressing challenges such as hardware-software compatibility, real-time data acquisition, and system complexity., This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615) and the GRIHO research group (2021 SGR 01620). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA inside the program ICREA Academia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Disseny d'un procés de producció continu de precursors de materials de canvi de fase (PCM) a partir de residus procedents de la indústria agroalimentària

  • Font Prieur, Daylen Yara
El projecte té com a objectiu obtenir materials de canvi de fase (PCM) a través de la producció de l'àcid 9,10-dihidroxiesteàric (DHSA). El procés inclou diverses etapes, pretenent l'extracció eficient dels àcids grassos insaturats a partir de greixos biològics no comestibles procedents de la indústria agroalimentària, per ser utilitzats com a PCM en l'emmagatzematge d'energia tèrmica. L'obtenció d'àcids i èsters són una proposta atractiva per a la indústria a causa del creixent interès i demanda, tant de productes fàcilment degradables per al medi ambient, com de substituts en síntesi orgàniques. El DHSA és un component valuós com a precursor de PCM a causa de les seves propietats termodinàmiques. Els PCM són materials útils com l'emmagatzematge d'energia tèrmica, susceptibles de tenir aplicacions a l'àmbit, per exemple, de la construcció. El procés inclou l'ús de substàncies químiques inflamables o explosives, cosa que en compromet l'escalat. Aquest projecte s'orienta a la producció a escala de PCM de manera segura a partir de biomassa no comestible., Aquest treball està parcialment finançat pel Ministeri de Ciència i Innovació - Agència Estatal de Recerca (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) i el Ministeri de Ciència, Innovació Estatal de Recerca (AEI) (RED2022-134219-T). ). Els autors agraeixen a la Generalitat de Catalunya l’acreditació de qualitat concedida al grup de recerca GREiA (2021 SGR 01615). GREiA és un agent certificat TECNIO en la categoria de desenvolupadors tecnològics de la Generalitat de Catalunya. Aquest treball està parcialment secundat per ICREA dins del programa ICREA Academia. Aquest projecte está cofinançat pel programa de recerca i innovació de la Unió Europea Horizon Europe, en el marc del projecte NitRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Use of Textile Fiber Waste to Improve the Thermal and Mechanical Performance of Cement-Based Mortar

  • Ayed, Rabeb
  • Borri, Emiliano
  • Zsembinszki, Gabriel
  • Bouadila, Salwa
  • Cabeza, Luisa F.
  • Lazaar, Mariem
Ayed, R., Borri, E., Zsembinszki, G., Bouadila, S., Cabeza, L.F., Lazaar, M. (2024). Use of Textile Fiber Waste to Improve the Thermal and Mechanical Performance of Cement-Based Mortar. In: Ungureanu, V., Bragança, L., Baniotopoulos, C., Abdalla, K.M. (eds) 4th International Conference "Coordinating Engineering for Sustainability and Resilience" & Midterm Conference of CircularB “Implementation of Circular Economy in the Built Environment”. CESARE 2024. Lecture Notes in Civil Engineering, vol 489. Springer, Cham. https://doi.org/10.1007/978-3-031-57800-7_25, Improving the thermal properties of materials used in buildings is crucial to reducing energy demand and consumption. This study investigated the use of textile fiber waste in cement-based composites for construction applications. Mechanical and thermal characterizations were carried out to assess the behavior of cement mortars with different percentages of two types of textile fibers after 7 and 28 days of water hardening. The results show that the incorporation of fibers can significantly improve the thermal insulation capacity of buildings by reducing the thermal conductivity of cement mortar by up to 52%. In addition, the use of textile fibers can improve themechanical strength of the cement mortar, especially with a high fiber content and a longer curing time., The authors would like to thank the Research and Technology Center of Energy of Borj-Cedria, Tunisia, Ministry of Higher Education and Scientific Research for supporting this study. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This publication is based upon work from COST Action CircularB, supported by COST (European Cooperation in Science and Technology). The authors from GREiA Research Group would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREAAcademia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental evaluation of different macro-encapsulation designs for PCM storages for cooling applications

  • Rehman, Omais Abdur
  • Palomba, Valeria
  • Vérez, David
  • Borri, Emiliano
  • Frazzica, Andrea
  • Brancato, Vincenza
  • Botargues, Teresa
  • Ure, Zafer
  • Cabeza, Luisa F.
Extensive research has been conducted on utilizing phase change materials for cooling applications, making it one of the most explored techniques in this domain. This research paper presents a comprehensive performance evaluation of a latent heat thermal energy storage unit featuring three distinct macro-encapsulation designs for phase change materials. The study aims to assess the thermal performance, efficiency, and practical applicability of these macro-encapsulation designs in a storage system. The PCM macro-encapsulation designs under investigation include cylindrical and rectangular shapes, each possessing different geometry. Two different configurations have been considered in this study. One configuration contains same PCM mass in order to have similar storage capacity while the other configuration has maximum PCM mass that can be inserted inside the tank. The used phase change material is a salt hydrate with melting temperature of 17 °C. The experimental setup consists of a controlled test rig that simulates real-world conditions and enables the comparative analysis of the three designs. Key performance parameters such as the charging and discharging time, temperature profiles, heat transfer rate, and energy storage/retrieval rates are measured and analysed. The results obtained from the experimental study provide valuable insights into the thermal behaviour, energy storage capacity, and overall effectiveness of the three macro-encapsulation designs. It is important to mention that use of an encapsulation design is highly dependent on application. The findings of this study contribute to the understanding of the impact of different macro-encapsulation designs on performance of thermal energy storage units. The results serve as a basis for optimizing macro-encapsulation designs, improving the efficiency and reliability of latent heat storage systems, and promoting their wider adoption in various energy management applications., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 101007976 (CO-COOL). This work is partially supported by ICREA under the ICREA Academia programme. This work is also partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021- 123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Use of artificial intelligence methods in designing thermal energy storage tanks: A bibliometric analysis

  • Mehraj, Nadiya
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
This bibliometric study examines the use of artificial intelligence (AI) methods, such as machine learning (ML) and deep learning (DL), in the design of thermal energy storage (TES) tanks. TES tanks are essential parts of energy storage systems, and improving their design has a big impact on how effectively and sustainably energy is used. With the increasing availability and advancements in AI techniques, researchers explored their application within the field of TES tank design to address challenges related to structural analysis, material selection, and optimization. However, a comprehensive analysis of the current state of research, trends, and potential areas for improvement is lacking. This study aims to bridge this gap by analysing scientific papers, patents, and publications in conference proceedings from the Scopus database to identify trends, research gaps, and areas of importance in this domain. The novelty of this study lies in its focused examination of AI methods specifically applied to TES tank design, providing a unique perspective on the intersection of these two important fields. By conducting a thorough bibliometric analysis, this study offers original insights into the current landscape and future directions of AI-enabled TES tank design research. The methodology involves a systematic search query and the use of VOSviewer software for keyword analysis. The results indicate a notable increase in publications during recent years (2020-August 2023), aligning with the growing focus on sustainable energy solutions. The most frequent keywords, such as TES, genetic algorithm (GA), and phase change material (PCM), suggest a focus on improving optimization of TES tanks with AI, while the least common keywords highlight specific areas with limited work and opportunities for future studies. In conclusion, this bibliometric analysis underscores the potential of AI to enhance the design and performance of TES tanks, emphasizes the value of further research in this area, and identifies opportunities for future advancements in AI-enabled TES tank design to contribute to energy efficiency and sustainability efforts., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU; TED2021-129462B-I00; and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to their research group (2021 SGR 01615). GREiA is TECNIO a certified agents in the category of technological development of the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental characterization of phase change materials for thermal energy storage in the temperature range between 270 °C and 400 °C

  • Martínez, Franklin R.
  • Borri, Emiliano
  • Ushak, Svetlana
  • Mani Kala, Saranprabhu
  • Prieto, Cristina
  • Cabeza, Luisa F.
Thermal energy storage (TES) with phase change materials (PCM) is an interesting technology to be used to improve the energy efficiency of industrial processes, contributing to their decarbonization and the integration of renewable energy sources. Even though literature lists many materials that can be used as PCM in the temperature range between 270 °C and 400 °C, most of them lack a full characterisation, jeopardising their potential implementation by practitioners and scientists. Therefore, this paper presents a complete experimental characterisation of 24 PCMs, with melting temperature, melting enthalpy, degradation temperature, and thermal conductivity in the solid state (at room temperature) determination. Moreover, corrosion tests with two different stainless-steel fibres and with Alloy 20 fibres is presented. The findings obtained in the characterization highlight the necessity of these analyses, as notable differences were observed compared to the available data, particularly in thermal stability and thermal conductivity. Moreover, the findings obtained in the compatibility test reveals that out of the 24 selected PCMs, 11 are potentially compatible with Alloy 20, and 8 with both stainless-steel fibres under environmental conditions (air atmosphere). Finally, the results presented will allow researchers and practitioners to have very detailed data on the characterisation of those PCMs., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovacion´ - Agencia Estatal de Investigacion´ (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/ 501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N◦ 1523A0006 and ANID/FONDECYT REGULAR N◦ 1231721 projects
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Modelat de tancs d’emmagatzematge d’energia tèrmica mitjançant l’ús d’eines d’intel·ligència artificial

  • Rojas Cala, Edgar Felipe
Les fonts d’energia renovable s’enfronten a múltiples desafiaments, entre els quals hi ha la necessitat de garantir una producció contínua. Una solució a aquest problema és l’emmagatzematge de l’energia generada per utilitzar-la en moments en què aquestes fonts no siguin eficients. Una alternativa viable és l’emmagatzematge d’energia tèrmica (TES, per les seves sigles en anglès). Aquesta tecnologia consisteix en un sistema format per una part de transport i una altra d’emmagatzematge, essent aquesta darrera especialment important, ja que permet reduir les pèrdues energètiques i augmentar l’eficiència del sistema. modelatge la simulació de l’emmagatzematge d’energia tèrmica, concretament mitjançant dinàmica de fluids computacional (CFD, per les seves sigles en anglès), requereix habitualment eines especialitzades, personal qualificat i una inversió considerable tant en recursos computacionals com econòmics. En aquest context, aquest estudi proposa una alternativa més accessible i eficient als mètodes convencionals de modelatge: l’ús d’eines d’intel·ligència artificial (IA) per a la simulació de dipòsits TES. La recerca va començar amb una revisió de l’estat de la qüestió, on es va identificar una oportunitat de desenvolupament deguda a un buit existent en l’aplicació de la IA al modelatge de dipòsits TES. A partir d’aquesta troballa, es va dur a terme una primera fase experimental utilitzant un disseny senzill de dipòsit TES. Es va entrenar un model de xarxa neuronal amb dades generades mitjançant simulacions CFD convencionals. Els resultats obtinguts van ser prometedors i van evidenciar el potencial d’aquesta aproximació per a una implementació a major escala. En una segona etapa, la recerca es va orientar al desenvolupament d’una eina d’IA més robusta, versàtil i escalable per al modelatge de dipòsits TES. Es van establir dos objectius principals: primer, modelar el comportament del dipòsit en diferents moments temporals; segon, permetre que el model es pogués generalitzar a diferents configuracions de dipòsit, variant la quantitat de components interns. Ambdues línies de treball van donar resultats encoratjadors. Tanmateix, es va fer evident la necessitat d’una recerca més profunda i multidisciplinària que abordi altres aspectes rellevants, amb l’objectiu de desenvolupar una eina capaç de substituir els mètodes actuals de modelatge de dipòsits TES., Aquest treball està parcialment finançat pel Ministeri de Ciència i Innovació - Agència Estatal de Recerca (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) i el Ministeri de Ciència, Innovació Estatal de Recerca (AEI) (RED2022-134219-T). ). Els autors agraeixen a la Generalitat de Catalunya l’acreditació de qualitat concedida al grup de recerca GREiA (2021 SGR 01615). GREiA és un agent certificat TECNIO en la categoria de desenvolupadors tecnològics de la Generalitat de Catalunya. Aquest treball està parcialment secundat per ICREA dins del programa ICREA Academia. Aquest projecte está cofinançat pel programa de recerca i innovació de la Unió Europea Horizon Europe, en el marc del projecte NitRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Diseño de tanques de almacenamiento de energía termica (TES) mediante el uso de redes neuronales e inteligencia artificial

  • Rojas Cala, Edgar Felipe
Los tanques de almacenamiento de energía térmica son depósitos que permiten almacenar energía térmica para ser usada después de mucho tiempo; esto, gracias al uso de diferentes materiales y diseños que permiten absorber, almacenar yliberar esta energía, Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) y el Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen al Gobierno de Cataluña la acreditación de calidad concedida al grupo de investigación GREiA (2021SGR01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos del Gobierno de Cataluña. Este trabajo está parcialmente apoyado por ICREA dentro del programa ICREA Academia. El proyecto NitRecercaCat (GA 101061189) está cofinanciado por el programa de investigación e innovación Horizonte Europa de la Unión Europea.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Increasing the sustainability of buildings by using thermal energy storage

  • Cabeza, Luisa F.
  • Zsembinszki, Gabriel
  • Palomba, Valeria
  • Borri, Emiliano
  • Lapka, Miloslav
  • Mateu Piñol, Carles
  • Beyne, Wim
  • Mani Kala, Saranprabhu
The final energy consumption of the built environment depends on the mismatch between its instantaneous energy demand and the energy supplied by on-site sources: buildings need to be cooled when there is abundant environmental heat and heated when the surrounding environment is cold. Thermal energy storage (TES) can help to reduce the global warming potential of buildings by storing environmental, renewable or waste heat for later use when heating is needed. In this Review, we assess the economic, environmental and social aspects of TES technologies. TES tanks require high charging and discharging power, calling for the development of new heat exchangers and storage media, such as phase-change materials. Integrating TES into local energy communities could reduce energy costs and lower the emissions caused by space and water heating, but challenges remain: price volatility and the deployment of longer-term thermochemical TES for seasonal storage, for example. The efficiency of TES operation could be increased by using advanced control systems, including artificial intelligence techniques. With the development of increasingly complex systems for TES, we highlight the importance of circular design thinking and end-user engagement in optimizing the development and deployment of future TES systems., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) and (RED2022-134219-T). The authors at the University of Lleida thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA inside the program ICREA Academia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Numerical analysis of an optimal metal wool-phase change material for thermal energy storage with exceptionally high power density

  • Ribezzo, Alessandro
  • Morciano, Matteo
  • Zsembinszki, Gabriel
  • Mani Kala, Saranprabhu
  • Borri, Emiliano
  • Bergamasco, Luca
  • Fasano, Matteo
  • Chiavazzo, Eliodoro
  • Prieto, Cristina
  • Cabeza, Luisa F.
The adoption of thermal energy storage (TES) systems based on phase change material (PCM) remains limited by their low thermal conductivity, which restricts power density. Existing heat transfer enhancement techniques are often costly or come with significant drawbacks, leaving a gap for an effective and affordable solution. This study highlights metal wool as a promising alternative, offering low cost, ease of application, and retrofitting potential. While previous experiments demonstrated substantial improvements in power density using copper wool, a comprehensive numerical model to further optimize this technique is presented here. The model, incorporating CFD simulations and uncertainty analysis, was validated for bulk PCM and two copper wool-PCM composites before being extended to a wool material analysis. First, possible alternatives to copper as wool material were tested, highlighting aluminum as a viable candidate. Then, the proposed composite was found to match the discharging performance of a PCM with an effective thermal conductivity of 2.5 W/mK, a value rarely achieved by conventional enhancement techniques. Additionally, a techno-economic comparison revealed that copper wool delivered a 14.7-fold increase in thermal conductivity relative to liquid PCM at ¿6 per kg of PCM additivated¿a performance unmet by metal foams and nanocomposites. These findings confirm metal wool as a viable cost-effective and high-performance solution for improving TES systems, partially bridging the gap between efficiency and affordability., A.R. and E.C. acknowledge funding under the National Recovery and Resilience Plan (NRRP), Mission 4 Component 2 Investment 1.3—Call for tender No. 1561 of 11.10.2022 of Ministero dell’Università e della Ricerca (MUR); funded by the European Union—NextGenerationEU. This work was partially funded by the Ministerio de Ciencia e Innovacion’ - Agencia Estatal de Investigacion’ (AEI) (PID2021-123511OB-C31-MCIN/AEI/10.13039/501100011033/ FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Department de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/ 10.13039/501100011033 and FSE+. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 101036910
Recercat. Dipósit de la Recerca de Catalunya
Publicación Capítulo o parte de un libro (BookPart)

Buildings (< 50 kWh/day). Integrated Batteries with Phase Change Materials (PCM) for Peak Shaving and Load Management: The HYBUILD Example

  • Frazzica, Andrea
  • Valeria , Palomba
  • Aloisio, Davide
  • Zsembinszki, Gabriel
  • Ferraro, Marco
  • Sergi, Francesco
  • Cabeza, Luisa F.
The continuous increasing of renewable-based energy systems, both for heating and power generation, at building level requires the development of innova-tive compact hybrid energy storages. These technologies are able to support the flex-ible operation of such complex systems, increasing the exploitability of renewables and the overall system efficiency. In this chapter, a brief overview of different storage technologies, such as thermal, electric and hybrid, at building level is provided, mostly focusing on their integration with onsite renewable generation and smart grids. The analysis highlights the relevant role of flexible energy storages at building level as well as the lack of innovative components able to provide multiple services (e.g. heating, cooling, domestic hot water and power) to buildings. In such a back-ground, the experience carried out in the framework of the EU-funded HYBUILD project is described. The overall concept, integrating electric batteries, latent, and thermochemical storages, with highly efficient reversible heat pumps is described, showing the different options developed for continental and mediterranean climates. The fully integrated Mediterranean system, validated both at lab-scale and in a demo building, demonstrated the ability of increasing the share of renewables in buildings, maximizing the self-consumption and increasing the overall energy efficiency of the system., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 768824 (HYBUILD). This work was partially funded by the Ministerio de Ciencia, Innovación y Universidades de España (RTI2018-093849-B-C31–MCIU/AEI/FEDER, UE) and the Ministerio de Ciencia e Inno-vación (PID2021-123511OB-C31—MCIN/AEI/https://doi.org/10.13039/501100011033/FEDER, UE) and by the Ministerio de Ciencia, Innovación y Universidades–Agencia Estatal de Investi-gación (AEI) (RED2018-102431-T and RED2022-134219-T). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537 and 2022 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Transient performance modelling of solar tower power plants with molten salt thermal energy storage systems

  • Tagle-Salazar, Pablo D.
  • Cabeza, Luisa F.
  • Prieto, Cristina
Concentrating solar power (CSP) has emerged as a dynamic and promising technology, demonstrating a burgeoning market potential for power generation through the utilization of solar thermal resources. Notably, global installed capacity has witnessed a substantial uptick in recent years, indicative that this technology is increasing traction worldwide. To optimize the utilization of CSP systems, particularly during periods of low or absent solar radiation, the integration of thermal energy storage (TES) systems using molten salts has become a prevailing strategy. This research introduces an innovative transient modelling tailored for the comprehensive annual performance analysis of a solar tower power plant coupled to a two-tank TES system, incorporating molten salts as the storage medium. The modelling of the power plant is conducted using OpenModelica, a versatile software platform renowned for its capability in system-level modelling and simulation. The simulation outcomes encompass a power plant configuration boasting a turbine gross output of 110 MWe. The results of performance parameters are subsequently contrasted with those generated by commercially available software tool, effectively corroborating the accuracy and effectiveness of the proposed simulation approach. The obtained results demonstrate a favourable concurrence in the transient behaviour of performance parameters, considering heat flows, state of charge, net power, and others, with a discrepancy of less than 1 % in annual production when benchmarked against a commercial software reference. Particularly, the incorporation of the local heat loss due to assembly defects within the thermal modelling of the TES system exerts a discernible albeit relatively minor influence on the overall performance of the power plant. The occurrence of local heat loss primarily stems from distortions or imperfections within the construction, including the structure, insulation layers, or foundation, thereby creating thermal bridges between the storage fluid and the external ambient environment. This impact, while small, is not negligible, as it introduces the potential for the power block to unexpectedly shut down owing to TES system depletion, a behaviour that is challenging to simulate when neglecting local heat loss., CSP-ERA.NET is supported by the European Commission within the EU Framework Programme for Research and Innovation Horizon 2020 (Cofund ERA-NET Action, N° 838311). This study receives funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU”/“PRTR”. This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental and computational assessment of building structures reinforced with textile fiber waste to improve thermo-mechanical performance

  • Ayed, Rabeb
  • Borri, Emiliano
  • Skouri, Safa
  • Lachheb, Mohamed
  • Bouadila, Salwa
  • Younsi, Zohir
  • Cabeza, Luisa F.
  • Lazaar, Mariem
Faced with the growing demand for energy-efficient construction and the need to address environmental challenges, the building sector must innovate to reduce energy consumption and promote sustainability. This study investigates a dual solution to these challenges by enhancing the thermo-mechanical performance of building materials through the integration of textile fiber waste, using a combination of experimental and computational methodologies. This investigation focused on incorporating textile fiber wastes in cementitious composites for construction applications. A series of mechanical and thermal tests were carried out on the cement mortars with different proportions of incorporated textile fibers after 7 and 28 days of water curing. The results showed that the incorporation of fibers can significantly improve the thermal insulation of buildings by reducing the thermal conductivity of cement mortar by up to 52%. To complement experimental findings, computational models were developed using COMSOL Multiphysics 6.2 software to predict the thermal diffusivity and volumetric heat capacity of textile-reinforced mortars. These models revealed that mortars incorporating 40% textile fibers as a sand replacement achieved significant reductions in thermal conductivity, thermal diffusivity, and volumetric heat capacity by approximately 40%, 21%, and 23%, respectively, compared with ordinary cement mortar. Furthermore, this study numerically examined the potential of combining textile-reinforced mortar with phase-change material (PCM) in building applications. The aim of the research was to overcome the challenges of cooling buildings in scorching summer conditions. The optimization of roof and wall composition was based on an assessment of air temperature variation within a space., Funding This study was supported by the Thermal Processes Laboratory of the Research and Technology Center of Energy (CRTEn) and the University of Tunis El Manar in Tunisia. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This publication is based upon work from COST Action CircularB, supported by COST (European Cooperation in Science and Technology). This work is partially supported by ICREA under the ICREA Academia programme. Acknowledgments The authors from GREiA Research Group would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme. This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Enhancement of heat transfer through the incorporation of copper metal wool in latent heat thermal energy storage systems

  • Ribezzo, Alessandro
  • Morciano, Matteo
  • Zsembinszki, Gabriel
  • Risco Amigó, Santiago
  • Mani Kala, Saranprabhu
  • Borri, Emiliano
  • Bergamasco, Luca
  • Fasano, Matteo
  • Chiavazzo, Eliodoro
  • Prieto, Cristina
  • Cabeza, Luisa F.
The design of thermal energy storage (TES) tank is the key part that can limit charging and discharging process. Most research findings highlight that the use of fins augments the heat transfer rate. This work experimentally investigates the use of aligned copper wools as fillers to enhance the thermal performance of a lab-scale shelland- tube TES tank filled with phase change material (PCM). Two copper wools with different fibre thicknesses were chosen and discretely laid around the TES tank tubes in two design patterns. Accordingly, five shell-andtube TES tank configurations were obtained, including the reference, for performance evaluation. The TES tank was loaded with n-octadecane as PCM for all the cases studied. The results showed up to a 16 % reduction in melting time with the inclusion of copper wool. The TES tank significantly increased the mean power during charging (53 %) and discharging (205 %). The addition of metal wool into the TES tank enables the PCM to release the heat at a constant temperature during the entire phase transition process. And the overall efficiency of the TES tank was found to get improved. Therefore, a copper wool integrated TES tank would be a beneficial addition to thermal energy storage systems., This project was funded by the European Union's Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Department de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Investigation of melting process in a PCM-based modular shell-and-coil latent thermal energy storage unit filled with coconut oil using image-processing-based techniques

  • Andrzejczyk, Rafał
  • Rogowski , Michał
  • Saqib, Muhammad
  • Muszyński, Tomasz
  • Cabeza, Luisa F.
This study explores the melting of coconut oil, a biodegradable phase-change material, in a shell-and-coil latent heat thermal energy storage unit under a constant heat flux of 519 W/m2, optimized through prior parametric studies of coil geometries and boundary conditions. A novel image processing approach, implemented via MATLAB's Image Segmenter, employs two distinct methods to analyze the melting process. The first method uses binarization to quantify the liquid fraction, revealing exponential growth that confirms convection-driven heat transfer, enhanced by coconut oil's low thermal conductivity. The second method calculates the equivalent diameter of the melting front, based on the coil's elliptical shape, to track its spatial progression. Compared to volume-averaged temperature calculations, the liquid fraction shows good initial agreement but diverges after 2000s due to image processing limitations, such as sensitivity to lighting and coil boundary effects. A theoretical model for melting front thickness was developed, though further experiments are needed for generalization. With low heat flux uncertainty this study underscores the potential of image processing for non-intrusive analysis of complex LTES geometries, advancing designs for low-temperature applications like solar thermal systems. The following study will be used to develop an enhanced and optimized model for complex geometries based on image processing techniques in the future., This research work was supported by the National Centre for Research and Development, Poland (Project No. LIDER/4/0008/L-9/ 17/NCBR/2018). Special thanks to Mr. Przemysław Kozak and PhD Michal Fabrykiewicz who were Lider project team members. This work was partially funded by the Ministerio de Ciencia e Innovacion ´ - Agencia Estatal de Investigacion ´ (AEI) (PID2021-123511OB-C31 - MCIN/AEI/1 0.13039/501100011033/FEDER, UE and RED2022-134219-T). Dr. Cabeza would also like to thank the Generalitat de Catalunya for the quality accreditation granted to her research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers of the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Molten salts tanks thermal energy storage: aspects to consider during design

  • Prieto, Cristina
  • Blindu, Adrian
  • Cabeza, Luisa F.
  • Valverde, Juan
  • García, Guillermo
Concentrating solar power plants use sensible thermal energy storage, a mature technology based on molten salts, due to the high storage efficiency (up to 99%). Both parabolic trough collectors and the central receiver system for concentrating solar power technologies use molten salts tanks, either in direct storage systems or in indirect ones. But even though this is a mature technology, it still shows challenges in its implementation and operation. This paper underscores the critical importance of stringent design criteria for molten salt tanks in thermal storage technology. Focusing on the potential ramifications of design failures, the study explores various dimensions where an inadequate design can lead to severe consequences, even jeopardizing the viability of the entire technology. Key areas discussed include structural integrity, corrosion, thermal shock, thermal expansions, and others. By elucidating the multifaceted risks associated with design shortcomings, this paper aims to emphasize the necessity of thorough reviews and adherence to robust design principles for ensuring the success, safety, and sustainability of thermal storage technology., This work was partially funded by the Ministerio de Ciencia e Innovación de España [(PID2021-123511OB-C31—MCIU/AEI/FEDER, UE) (TED2021-132216A-I00) (RED2022-134219-T)].
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Potential of the Use of Sodium Chloride (NaCl) in ThermalEnergy Storage Applications

  • Cabeza, Luisa F.
  • Martínez, Franklin R.
  • Zsembinszki, Gabriel
  • Borri, Emiliano
Energy storage is a group of technologies that decrease the gap between energy supply and energy demand. Thermal energy storage (TES) reduces this gap at not only different temperatures but also at different places or power. Design criteria include the integration of the storage system into the whole application system, maximum load, and high-energy density. Since energy density is given by the material used, the selection of the storage material is key to the success of any energy storage system. In this paper, the potential of sodium chloride (NaCl) to be used in TES, both using sensible TES and latent TES, is evaluated for low-temperature applications and for high-temperature ones. This material is found to have high potential for successful applications, both in buildings and in industry., This work was partially funded by the Ministerio de Ciencia eInnovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB - C31—MCI N/A E I/10.13 039/5 0110 0 011033/ F E DER ,UE), and Ministerio de Ciencia e Innovación—Agencia Estatal deInvestigación (AEI) (RED2022-134219-T). Franklin R. MartinezAlcocer thanks the National Doctorate Scholarship for foreign stu-dents ANID 2021 Folio 21211932 for the financial support in the re-search. This work is partially supported by ICREA under the ICREAAcademia program. The authors would like to thank the CatalanGovernment for the quality accreditation given to their research group(2021 SGR 01615). GREiA is a certified agent of TECNIO in the cate-gory of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Compatibility of carbonate mixtures to be used as molten salts with different metal alloys to be used as container materials

  • Cabeza, Luisa F.
  • Martínez, Franklin R.
  • Borri, Emiliano
The energy transition can only be achieved if the global energy sector is transformed from a fossil-based system to a zero-carbon-based source system. To achieve this aim, two technologies have shown promising advances in high-temperature application. Concentrating solar power (CSP) plants are seen as a key technology to achieve the needed energy transition, and carbon dioxide (CO2) capture and storage (CCS) is a promising technology for decarbonizing the industrial sector. To implement both technologies, molten carbonate salts are considered promising material. However, their corrosive behavior needs to be evaluated, especially at high temperatures, where corrosion is more aggressive in metal structures. This paper presents an experimental evaluation of the static corrosion of two molten carbonate salts, a Li2CO3-Na2CO3-K2CO3-LiOH·H2O (56.65-12.19-26.66-4.51wt.%) mixture and a Li2CO3 salt, under an air atmosphere with five corrosion-resistant metal alloys, including Alloy 600, Alloy 601, Alloy 625, Alloy 214, and Alloy X1. In this study, the corrosion rate and mass losses were quantified. In addition, in all the cases, the results of the experimental evaluation showed corrosion rate values between 0.0009 mg/cm2·yr and 0.0089 mg/cm2·yr., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE), and Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N° 1522A0006 and ANID/FONDECYT REGULAR N° 1231721 projects. This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the company STAX for their contribution to the study.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Use of bibliometric analysis to evaluate the influence of cement and concrete on carbon capture, utilization, and storage over the years

  • Santini, Carolina
Cement industry produced high quantities of CO2 increasing the concept of concrete as a nonsustainable material. This work aim to analyse all the relevant research focused on CO2 capture, utilization and storage (CCUS) in cement-concrete sector., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE), and by Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia This project is co-funded by the European Union’s research and innovation programme Horizon Europe, under the project NitRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Desarrollo y optimización de nuevos PCM en base a sales inorgánicas, para su aplicación en sistemas de almacenamiento de energía térmica a altas temperaturas (Nit Europea de la Recerca 2024)

  • Martínez, Franklin R.
Las plantas de concentración solar de potencia CSP, son instalaciones industriales donde se aprovecha la radiación solar para producir energía eléctrica. Los rayos solares son reflejados desde una superficie extensa y concentrados en un solo punto (superficie reducida) para calentar el fluido calo portador (HTF) a una temperatura de 565ºC, este fluido caliente ingresa al intercambiador de calor donde cede al agua el calor acumulado, produciendo vapor, el cual ingresa a la turbina donde se genera energía eléctrica., Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE) y el Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen a la Generalitat de Catalunya la acreditación de calidad concedida al grupo de investigación GREiA (2021 SGR 01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos de la Generalitat de Catalunya. Este trabajo está parcialmente respaldado por ICREA dentro del programa ICREA Academia. Este proyecto está cofinanciado por el programa de investigación e innovación de la Unión Europea Horizon Europe, en el marco del proyecto NitRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Evaluation of the social impact of an energy system for residential heating applications based on a novel seasonal thermal energy storage

  • Borri, Emiliano
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Thermal energy storage (TES) is a key player in the energy transition to support the integration of renewable sources and reduce the energy demand supplied by fossil fuels. The EU-funded project SWS-Heating aims to develop a novel seasonal thermal energy storage based on selective water sorbents for domestic heating to increase the share of renewables. Although the main performance indicator of new technologies is energy efficiency optimization, social impact of TES is an overlooked aspect representing a strong barrier to market deployment of novel technologies. Therefore, this study uses social life-cycle assessment (S-LCA) techniques to evaluate the social impact of the proposed systems described above. The inventory developed in this study is based on qualitative data from industrial companies involved in the different stages of the system life cycle. Results showed that the system has a medium-high social impact with great potential for improvement especially in the manufacturing and end-of-life stages. In particular, to increase the value of social impact more effort should be put by companies to strengthen the engagement with local communities and support sustainability with value chain actors., This project was funded by the European Union's Horizon 2020 Research and Innovation Programme under No. 764025 (SWS-HEATING). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (PID2021 - 123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, EU and RED2022-134219-T). The authors thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA within the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Environmental performance of a multi-energy liquid air energy storage (LAES) system in cogeneration asset – A life cycle assessment-based comparison with lithium ion (Li-ion) battery

  • Tafone, Alessio
  • Borri, Emiliano
  • Cabeza, Luisa F.
  • Romagnoli, Alessandro
Increase in energy demand is shaping both developed and developing countries globally. As a result, the endeavour to reduce carbon emissions also encompasses electrical energy storage systems to ensure environmentally friendly power production and distribution. Currently, the scientific community is actively exploring and developing new storage technologies for this purpose. The focus of this work is to compare the eco-friendliness of a relatively novel technology such as liquid air energy storage (LAES) with an established storage solution such as Li-Ion battery (Li-ion). The comparison is carried out through Life Cycle Assessment (LCA) methodology which aims to assess the environmental impacts from each life stage, according to different impact categories. In particular, the study refers to the unitary storage and the delivery of electricity as well as cooling energy, considering all the inefficiencies and limits of each technology. The results show that in the full electric case study Li-ion battery environmentally outperform LAES due to (1) the higher round trip efficiency and (2) the significantly high environmental impact of the diathermic oil utilized by LAES, accounting for 92 % of the manufacture and disposal phase. Conversely, the cogeneration case study highlights that the “flexibility” and “dualism” of LAES, capable to efficiently deliver both electricity and cooling, offset the impact related to the higher electricity consumption during the use phase. Notably in energy mix frameworks with high share of primary energy source from fossil fuels, cogenerative LAES demonstrates superior environmental performance compared to Li-ion battery (i.e. 1302 kgCO2eq/MWhe vs 1140 kgCO2eq/MWhe for Singapore energy mix), attributable to its reduced electricity consumption., This project was funded by the European Union’s Horizon 2020 Research and Innovation Programme under No. 101007976 (COCOOL). This work is partially supported by ICREA under the ICREA Academia programme. This work is also partially funded by Ministerio de Ciencia e Innovacion´ —Agencia Estatal de Investigacion ´ (AEI) (PID2021- 123511OB-C31 - MCIN/AEI/10.13039/ 501100011033/FEDER, EU and RED2022-134219-T). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Development of a bio-inspired TES tank for heat transfer enhancement in latent heat thermal energy storage systems

  • Cabeza, Luisa F.
  • Mani Kala, Saranprabhu
  • Zsembinszki, Gabriel
  • Vérez, David
  • Risco Amigó, Santiago
  • Borri, Emiliano
Thermal energy storage (TES) systems play a very important part in addressing the energy crisis. Therefore, numerous researchers are striving to improve the efficiency of TES tanks. The TES technology has the potential to reach new heights when the biological behavior of nature is incorporated into the design of TES tanks. By mimicking the branched vein pattern observed in plants and animals, the heat transfer fluid (HTF) tube of a TES tank can enhance the heat transfer surface area, hence improving its thermal efficiency without the need to add other enhancements of heat transfer methods. Accordingly, in this study, a unique additive-manufacturing-based bio-inspired TES tank was designed, developed, and tested. A customized testing setup was used to assess the bio-inspired TES tank's thermal performance. A comparison was made between the bio-inspired TES tank and a conventional shell-and-tube TES tank. The latent TES system's thermal performance was significantly enhanced by the biomimetic approach for the design of a TES tank, even before the optimization of its design. The results showed that, compared to the shell-and-tube TES tank, the bio-inspired TES tank had a higher discharging rate and needed 52% less time to release the stored heat., This study has received funding from the European Union’s Horizon Europe Research and Innovation Programme under grant agreement No. 101103552 (SUSHEAT). However, the views and opinions expressed are those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE), Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI)—NextGeneration EU (TED2021-129462B-I00—MCIN/AEI/10.13039/501100011033/NextGenerationEU/PRTR), and Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work was partially supported by ICREA under the ICREA Academia program.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Development of copper metal wool incorporated in a latent thermal energy storage tank for improved charging and discharging

  • Mani Kala, Saranprabhu
  • Ribezzo, Alessandro
  • Zsembinszki, Gabriel
  • Borri, Emiliano
  • Prieto, Cristina
  • Cabeza, Luisa F.
The thermal energy storage tank is an essential component of a conventional thermal energy storage system. Nevertheless, low charging and discharging rates is one of the different problems associated with them. Many research studies were conducted to improve the charging and discharging characteristics of thermal energy storage tanks. Those include the addition of nanoparticles, heat pipes, metal foams, and encapsulation of the phase change material. Even though those approaches improved the thermal performance of the storage tank, they also promoted some problems, like nanoparticle deposition, suppression of natural convection, and reduced energy density. This study, used a different approach to improve the thermal performance, integrating copper metal wool of two discrete thicknesses perpendicular to the heat transfer fluid carrying tubes. Accordingly, with two different packaging factor four different configurations of metal wool-packed tanks were developed and compared against the reference, i.e., a conventional shell and tube tank. The thermal performance of the developed cases was tested using a custom-built test rig. The integration of copper metal wool reduced the charging and discharging time significantly. However, the fully stacked fine fibre wool packed tank showed a remarkable 85% reduction in solidification time and a 37.4% reduction in melting time compared to the conventional shell and tube tank. Moreover, it showed a higher mean power than all the developed cases, with 414% enhancement during the discharging cycle and 42% during the charging cycle. Thus, the incorporation of metal wool into a tank is an effective way to enhance its thermal performance., This project has received funding from the European Union’s Horizon 2020 Research and Innovation Programme under Grant Agreement N. 101036910 (StoRIES). This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors at the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Experimental evaluation of different macro-encapsulation designs for PCM storages for cooling applications

  • Rehman, Omais Abdur
This research activity presents a comprehensive performance evaluation of a latent heat thermal energy storage unit featuring three distinct macro-encapsulation designs for phase change materials. The study aims to assess the thermal performance, efficiency, and practical applicability of these macro-encapsulation designs within an energy storage system., Este trabajo está parcialmente financiado por el Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31-MCIN/AEI/10.13039/501100011033/FEDER, UE) y por el Ministerio de Ciencia, Innovación y Universidades – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). Los autores agradecen al Gobierno de Cataluña la acreditación de calidad concedida al grupo de investigación GREiA (2021SGR01615). GREiA es un agente certificado TECNIO en la categoría de desarrolladores tecnológicos por el Gobierno de Cataluña. Este trabajo está parcialmente apoyado por ICREA en el marco del programa ICREA Academia. Cofinanciado por el programa de investigación e innovación Horizon Europe de la Unión Europea, en el marco del proyecto NitRecerCat (GA101061189)..
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Innovative refractory concrete for high temperature thermal energy storage

  • Castro Chicot, José Ramón
  • Santini, Carolina
  • Zsembinszki, Gabriel
  • Mani Kala, Saranprabhu
  • Martínez, Franklin R.
  • Risco Amigó, Santiago
  • Fabiani, Claudia
  • Pisello, Anna Laura
  • Cabeza, Luisa F.
Thermal energy storage (TES) systems play an important role in the management of thermal energy and associated consumption. Furthermore, using TES, combustion of fossil fuels and their associated environmental impacts are avoided. In particular, demand for high temperature energy storage is increasing and research focuses on the development of suitable materials for these applications. A limited number of studies focus on the use of sensible heat storage systems that exploit concrete as a TES under high temperature conditions for concentrating solar power (CSP) plant systems. The main drawback to overcome in concrete TES is the degradation of the concrete after charging and discharging thermal cycles. This study aims to develop a novel concrete formulation designed for high-temperature applications and capable of withstanding thermal cycling. To achieve this, a refractory concrete was conceptualized using calcium aluminate cement (CAC) and refractory aggregates, specifically basalt and chamotte. The formulation also incorporates a heat treatment applied after the cu[[ring period to enhance its performance under extreme thermal conditions. This heat treatment is what allows to transform a CAC concrete, that unites the dispersed material through hydraulic nodes, into a refractory concrete, that unites the dispersed material through its ceramisation. The new concrete formulation was analysed to evaluate its performance before and after 25 thermal cycles. Results show that thermal conductivity and compressive strength after ceramisation have values around 1.7 W/m⋅K and 52 MPa, respectively. It was also observed that the initial thermal treatment was not necessary, because the ceramisation of the concrete can also be achieved during the thermal cycling process if the correct heating and cooling rates are used. The developed new concrete formulation containing refractory aggregates demonstrated excellent thermo-physical and mechanical properties that make it suitable for high-temperature TES applications (temperatures up to 700 ◦C)., This project has received funding from the European Union's Horizon 2020 Research and Innovation Programme under Grant Agreement 101036910 (StoRIES). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This study received funding from the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (MCIN/AEI/10.13039/501100011033) through the PCI2020-120695-2 project and the European Union “NextGenerationEU"/PRTR". The authors from University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme. This work was partially funded by the European Union—NextGenerationEU under Italian Ministry of University and Research (MUR) National Innovation Ecosystem grants ECS00000041— VITALITY—CUP J97G22000170005 and CUP B43C22000470005. The authors thank the PhD school in Energy and Sustainable Development at CIRIAF University of Perugia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Optimizing the design of TES tanks for thermal energy storage applications an integrated biomimetic-genetic algorithm approach

  • Mehraj, Nadiya
  • Mateu Piñol, Carles
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
Building upon an experimentally validated bio-inspired thermal energy storage (TES) tank design, this study introduced a novel computational framework that integrated genetic algorithms (GA) with biomimetic principles to systematically generate TES tank geometries. Inspired by natural thermal distribution patterns found in vascular networks, the AI-driven methodology explored 13 geometric parameters, focusing on branching structures and spatial distribution, and resulted in computationally generated designs with a 29% increase in heat transfer surface area while maintaining manufacturability constraints within a fixed tank diameter of 150 mm and height of 155 mm. Unlike previous biomimetic TES studies that relied on predefined geometric configurations, this approach developed AI-driven bio-inspired structures within experimentally validated dimensional constraints, ensuring geometric relevance while allowing for broader structural exploration. The resulting designs exhibited key characteristics of high-efficiency bio-inspired configurations while providing a systematic, scalable methodology for TES tank architecture. This study represented the first step in integrating AI-driven biomimicry into TES tank design, establishing a structured framework for generating high-performance, manufacturable configurations. While the current work focused on computational design, future research will emphasize experimental validation and real-world implementation to confirm the practical thermal and structural benefits of these AI-generated bio-inspired designs. By bridging the gap between computational intelligence and nature-inspired engineering, this research provided a scalable pathway for developing more efficient, manufacturable, and sustainable TES solutions for energy storage applications., Funding: This study has received funding from the European Union’s Horizon Europe Research and Innovation Programme under grant agreement No. 101103552 (SUSHEAT). Views and opinions expressed are, however, those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was also partially funded by Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI)—NextGeneration EU (TED2021-129462BI00— MCIN/AEI/10.13039/501100011033/ NextGenerationEU/PRTR, PID2021-123511OB-C31— MCIN/AEI/10.13039/501100011033/FEDER, UE, and RED2022-134219-T). Acknowledgments: This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Energy saving potential of variable thermophysical envelope energy storage technologies in different climatic regions

  • Ji, Pengcheng
  • Guo, Yong
  • Weschler, Louise B.
  • Cabeza, Luisa F.
  • Zsembinszki, Gabriel
  • Yang, Rui
  • Zhang, Yinping
Climate change mitigation necessitates higher use of renewable energy in buildings instead of fossil fuels. There is great potential to achieve this goal when the thermophysical properties of a building envelope are variable. To identify the ideal variable thermophysical properties (specific heat and thermal conductivity) for building envelopes located in given climate regions, an inverse problem approach based on particle swarm optimization (PSO) was employed. The energy consumptions of rooms were calculated when the building envelope thermophysical properties are ideally variable or constant for seven representative cities located in five climatic regions in China. The results show that when the thermal conductivity of exterior wall is ideally variable, the energysaving ratio can reach 7-15 % in seven cities, corresponding to energy saving amount of 0.03-0.78 kgce/(m2⋅year), and when the specific heat of interior building envelope is ideally variable, the energy saving ratio can reach 37-100 %, corresponding to energy saving amount of 0.21-3.06 kgce/(m2⋅year). The corresponding annual CO2 emission reduction is between 0.02 and 1.90 kg/(m2⋅year) and between 0.10 and 8.07 kg/(m2⋅year), respectively. Variable thermophysical properties have highest energy-saving and CO2 emission reduction potential in the severe cold region. Conversely, in the moderate temperature region, their impact is insignificant. The present study can help to provide direction for developing materials ith variable thermophysical properties for building envelopes in different climate regions., The research was supported by Natural Science Foundation of China (51976106, 52378102). This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31- MCIN/AEI/10.13039/501100011033/FEDER, UE and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors from the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental characterization of phase change materials for thermal energy storage for solar energy applications in the temperature range between 400 ºC and 600 ºC

  • Martínez, Franklin R.
  • Borri, Emiliano
  • Ushak, Svetlana
  • Mani Kala, Saranprabhu
  • Prieto, Cristina
  • Cabeza, Luisa F.
Concentrating solar power (CSP) plants are seen as a key technology to achieve the needed energy transition since its use together with a thermal energy storage (TES) system ensures electricity dispatchability decreasing CSP plants environmental impact and life cycle costs. Latent TES using phase change materials (PCMs) has risen as a very interesting storage technology for such applications. Nevertheless, the selection of the adequate TES system and PCM, is one of the problems researchers and practitioners face to implement such technology. This paper presents a full characterization of fifteen PCMs suitable to work in the temperature range 400-600 ◦C. Melting temperature, melting enthalpy, degradation temperature, and solid-state thermal conductivity are presented, complemented with corrosion behaviour tests against stainless steel and Alloy 20. Moreover, the findings obtained in the characterization of the selected fifteen PCMs highlight the need of these analyses, as notable differences were observed compared to the available data, particularly in thermal stability and thermal conductivity. Furthermore, the compatibility test reveals that out of the fifteen selected PCMs, only two PCMs (binary mixtures of carbonates) are potentially compatible with stainless-steel 314 and Alloy 20 fibres under environmental conditions (air atmosphere). Finally, the results presented will allow researchers and practitioners to have very detailed data on the characterisation of those PCMs., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE, and RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+. Franklin R. Martinez Alcocer thanks the National Doctorate Scholarship for foreign students ANID 2021 Folio 21211932 for the financial support in the research. S. Ushak acknowledges to ANID/PUENTE N° 1523A0006 and ANID/FONDECYT REGULAR N° 1231721 projects.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Use of molten salts tanks for seasonal thermal energy storage for high penetration of renewable energies in the grid

  • Prieto, Cristina
  • Tagle-Salazar, Pablo D.
  • Patiño-Rodríguez, David
  • Schallenberg-Rodriguez, Julieta
  • Lyons, Padraig
  • Cabeza, Luisa F.
Energy storage is acknowledged a key technology to meet the challenges posed by the energy transition. Shortterm grid-connected storage, based on Li-Ion batteries, is becoming commonplace but seasonal energy storage at grid-scale will be needed for deep decarbonisation of the electrical power system. Pumped hydropower is considered to be the only mature technology for such applications, but this paper demonstrates that two-tanks molten salts systems, that are used today in commercial concentrating solar power (CSP) plants, can also be considered a mature technology that can be used at large scale for seasonal energy storage. This was established by evaluating the annual heat losses of molten salts tanks using validated models of these systems. The results show that the heat losses in a very well insulated molten salts tanks are around 1 K/day, which would result in good economic performance of the power block even if storage was required for up to months., This work was partially funded by the Ministerio de Ciencia e Innovación de España TED2021-132216A-I00 funded by MCIN/AEI/10.13039/501100011033 and the European Union by NextGenerationEU/PRTR. This work was partially funded by the Ministerio de Ciencia e Innovación de España (PID2021-123511OB-C31 - MCIU/AEI/FEDER, UE; RED2022-134219-T). The authors at University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREiA (2021 SGR 01615). GREiA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Integration of thermal energy storage (TES) technologies in buildings

  • Ahmed, Waqar
1. What is thermal energy? What does thermal energy storage mean? Thermal energy is the energy that comes from heat. It's the energy that helps to keep things warm or cool. Thermal energy storage is a way to save heat or cold so you can use it later when you need it. 2. What does thermal energy storage (TES) do in buildings? TES helps to keep buildings warm in winter and cool in summer by storing heat or cold and using it when needed. A building with good TES system, we can reduce heating bills and use less energy from the electricity grid., This work was partially funded by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE), and by Ministerio de Ciencia e Innovación – Agencia Estatal de Investigación (AEI) (RED2022-134219-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia This project is co-funded by the European Union’s research and innovation programme Horizon Europe, under the project NitRecercat2425 (101162003).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal energy storage in energy communities: A perspective overview through a bibliometric analysis

  • Brunelli, Luca
  • Borri, Emiliano
  • Pisello, Anna Laura
  • Nicolini, Andrea
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
The climate and energy crisis requires immediate countermeasures. Renewable energy communities (RECs) are capable of enhancing the consumption of renewable energy, involving citizens with a leading role in the energy transition process. The main objective of a REC is to maximize the consumption of renewable energy by reducing the mismatch between energy supply and demand. This is possible through the use of strategies and technologies including energy storage systems. Among these, the use of thermal energy storage (TES) is an efficient strategy due to the lower investment required compared to other storage technologies, like electric batteries. This study aims to define the role of TES in RECs, through a bibliometric analysis, in order to highlight research trends and possible gaps. This study shows that the existing literature on TES does not present terms related to RECs, thus presenting a research gap. On the other hand, RESs address the topic of energy storage in the literature, without focusing on TES in particular but considering the general aspect of the topic. Therefore, this leaves open a possibility for the development of research on TES as a possible technology applied to a REC to maximize the renewable energy sharing., Funding: This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE) and by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (RED2022-134219-T). L. Brunelli acknowledges Fondazione Perugia for the support given through the “EDUCER” project (21082, 2022.0406). Acknowledgments: The authors at the University of Lleida thank the Generalitat de Catalunya for the quality accreditation granted to the GREiA research group (2021 SGR 01615). GREiA is a TECNIO-certified agent in the category of technological development of the Gobierno de Cataluña. This work is partially supported by ICREA inside the program ICREA Academia. L. Brunelli aknowledgments are due to the PhD school in Energy and Sustainable Development at CIRIAF from the University of Perugia.