Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 45
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Experimental study of hydrogen purge effects on performance and efficiency of an open-cathode Proton Exchange Membrane fuel cell system

  • Strahl, Stephan
  • Husar, Attila
  • Riera, Jordi
The performance and efficiency of an open-cathode PEM fuel cell system in dead-ended anode (DEA) configuration and hydrogen purges is analyzed in this work. Excess water and crossed-over nitrogen in the anode decrease the hydrogen concentration at the catalyst surface, which in turn causes performance losses. Purging the anode with hydrogen removes water and nitrogen and thus recovers the performance. However, this means wasting hydrogen and decreasing overall system efficiency. Gas chromatography was used to detect and quantify the accumulated nitrogen in the anode during DEA operation. The experiments show that the major performance limitation in the studied system is related to water instead of nitrogen. Moreover, oxygen was detected in the anode exhaust gas after long purge intervals, which is an indicator for corrosion of the cathode carbon support structure. Experimental observations revealed that the need for a hydrogen purge strongly depends on the operating conditions and the state-of-health of the fuel cell. It is shown that flooding on the anode and drying of the cathode catalyst layer may occur simultaneously during purged operation. Therefore, purge decisions must be evaluated online, depending on the operating conditions. © 2013 Elsevier B.V. All rights reserved., This work is partially funded by the National Projects MICINN DPI2011-25649 and MINECO ENE2012-36368, as well as by the 7th Framework Programme of the European Commission in the context of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) through the project PUMA-MIND FP7 303419., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance improvement by temperature control of an open-cathode PEM fuel cell system

  • Strahl, Stephan
  • Husar, Attila
  • Puleston, Pablo Federico
  • Riera, Jordi
Paper presented at the “Fundamentals & Developments of Fuel Cells Conference 2013 (FDFC2013)”, April 16–18, 2013, Karlsruhe, Germany., The work presented in this article combines experimental analysis and theoretical studies of temperature effects on the performance of an open-cathode, self-humidified PEM fuel cell system for the design of optimal control strategies. The experimental analysis shows the great potential of improving the system performance by proper thermal management. The most significant temperature dependent parameter of the system under study is the exchange current density. On the one hand it is influenced positively by a temperature increase as this lowers the activation barrier. On the other hand a higher temperature causes a reduction of the electrochemical active sites in the cathode catalyst layer due to lower water content in the ionomer and primary pores. Dynamic models for fuel cell temperature, liquid water transport and the related electrochemistry have been developed and validated against the experiment. A cascaded Extremum Seeking control algorithm with a local PI controller is proposed to regulate the temperature to a fuel cell voltage maximum. However, the slow dynamics of the temperature related catalyst-drying effect on performance complicate the optimal thermal management with model-free control strategies., This work is partially funded by the national project MICINN DPI2011-25649, as well as by the 7th Framework Programme of the European Commission in the context of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) through the project PUMA-MIND FP7 303419. The work of P. Puleston was supported by CONICET and UNLP (Argentina), as well as Marie Curie FP7-2011-IIF, ACRES (299767/911767) (EU). Finally, the authors highly appreciate the support of the LEICI and the UNLP in enabling a research stay of S. Strahl at the laboratory in La Plata., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Distributed parameter model simulation tool for PEM fuel cells

  • Sarmiento-Carnevali, María Laura
  • Serra-Prat, María
  • Batlle, Carles
In this work, a simulation tool for proton exchange membrane fuel cells (PEMFC) has been developed, based on a distributed parameter model. The tool is designed to perform studies of time and space variations in the direction of the gas channels. Results for steady-state and dynamic simulations for a single cell of one channel are presented and analyzed. Considered variables are concentrations of reactants, pressures, temperatures, humidification, membrane water content, current density, among others that have significant effects on the performance and durability of PEMFC., This work has been supported by national projects DISCPICO with reference DPI2010-15274, MESPEM with reference DPI2011-25649 and european project PUMA MIND., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A gain-scheduled LPV control for oxygen stoichiometry regulation in PEM fuel cell systems

  • Bianchi, Fernando D.
  • Kunusch, Cristian
  • Ocampo-Martínez, Carlos
  • Sánchez-Peña, Ricardo S.
The article addresses the LPV control of a Polymer Electrolyte Membrane Fuel Cell (PEMFC). In order to optimize efficiency, PEMFCs require reliable control systems ensuring stability and performance, as well as robustness to model uncertainties and external perturbations. On the other hand, PEMFCs present a highly nonlinear behavior that demands nonlinear and/or adaptive control strategies to achieve high performance in the entire operating range. Here, a linear parameter varying (LPV) gain scheduled control is proposed. The control is based on a piecewise affine LPV representation of the PEMFC, a model that can be available in practice. In order to deal with the saturation of the control action, an LPV anti-windup compensation is also proposed. The complete control strategy is applied to several experimental practical situations in a laboratory fuel cell system to evaluate its performance and the reliability of the proposed algorithms., The research of F.D. Bianchi was supported by the European Regional Development Funds (ERDF, FEDER Programa Competitivitat de Catalunya 2007-2013). The research of C. Kunusch has been supported by the Seventh Framework Programme of the European Community through the Marie Curie actions (GA: PCIG09-GA-2011-293876) and project Puma-Mind (GA: FCH-JU-2011-1-303419), as well as by the CICYT project DPI2011-25649 (MICINN-Spain). The research of C. Ocampo-Martinez has been supported by the project MACPERCON (Ref. 201250E027) of the CSIC. The research of R.S. Sánchez Peña has been supported by CONICET and grant PICT2008-290 from the PRH Program of the Ministry of Science, Technology and Innovation of Argentina., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electrode structure effects on the performance of open-cathode proton exchange membrane fuel cells: A multiscale modeling approach

  • Strahl, Stephan
  • Husar, Attila
  • Franco, Alejandro A.
In this paper we present a new dynamic multiscale model of an open-cathode Polymer Electrolyte Membrane Fuel Cell (PEMFC). The model describes two-phase water transport, electrochemistry and thermal management within a framework that combines a Computational Fluid Dynamics (CFD) approach with a micro-structurally-resolved model predicting the water filling dynamics of the electrode pores and the impact of these dynamics on the evolution of the electrochemically active surface area (ECSA). The model allows relating for the first time the cathode electrode structure to the cell voltage transient behavior during experimental changes in fuel cell temperature. The effect of evaporation rates, desorption rates and temperature changes on the performance of four different electrode pore size distributions are explored using steady-state and transient numerical simulations. The results are discussed with respect to water management and temperature control., This work is partially funded by the national project MICINNDPI2011-25649, as well as by the 7th Framework Programme of the European Commission in the context of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) through the project PUMA-MIND FP7 303419., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Experimental analysis of a degraded open-cathode PEM fuel cell stack

  • Strahl, Stephan
  • Gasamans, Noemí
  • Llorca, Jordi
  • Husar, Attila
The well-known challenges to overcome in PEM fuel cell research are their relatively low durability and the high costs for the platinum catalysts. This work focuses on degradation mechanisms that are present in open-cathode PEM fuel cell systems and their links to the decaying fuel cell performance. Therefore a degraded, open-cathode, 20 cell, PEM fuel cell stack was analyzed by means of in-situ and ex-situ techniques. Voltage transients during external perturbations, such as changing temperature, humidity and stoichiometry show that degradation affects individual cells quite differently towards the end of life of the stack. Cells located close to the endplates of the stack show the biggest performance decay. Electrochemical impedance spectroscopy (EIS) data present non-reversible catalyst layer degradation but negligible membrane degradation of several cells. Post-mortem, ex-situ experiments, such as cyclic voltammetry (CV), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) show a significant active area loss of the first cells within the stack due to Pt dissolution, oxidation and agglomeration. Scanning electron microscope (SEM) images of the degraded cells in comparison with the normally working cells in the stack show severe carbon corrosion of the cathode catalyst layers., This work is partially funded by the national projects MICINN DPI2011-25649 and MINECO ENE2012-36368, as well as by the 7th Framework Programme of the European Commission in the context of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) through the project PUMA-MIND FP7 303419., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development and implementation of a supervisor strategy and sliding mode control setup for fuel-cell-based hybrid generation systems

  • Moré, Jerónimo J.
  • Puleston, Pablo Federico
  • Kunusch, Cristian
  • Allué, Miguel
This paper presents the development and experimental results of a supervisor strategy and a sliding mode control setup to improve the performance of hybrid generation systems. The topology in this study is conformed by a core comprising a fuel cell module and a supercapacitor module, in combination with an alternative energy source module and an electrolyzer. In particular, a wind power turbine is considered as alternative power source to attain a hybrid generation system fully relying on renewable energy. First, a supervisor strategy is proposed to manage the power flows of the subsystems and coordinate the system as a whole. Subsequently, a sliding mode control setup for combined operation of the dc/dc power converters of the fuel cell/supercapacitor core is presented to track the power references synthesized by the supervisor control. Both control levels, supervisor strategy and sliding mode controllers, are implemented and assessed through extensive experimental tests under different wind conditions and heavy-load changes., This research was supported by the Universidad Nacional de La Plata, CONICET, and SECyT, from Argentina; by FP7-PEOPLE-2011 Marie-Curie Action, Project ACRES (IIF-299767/911767) and ACOFC (PCIG09-GA- 2011-293876) from the EU; by Project Puma-Mind (FCHJU-2011-1-303419); partially founded by Project MICINN DPI2011-25649 and supported by the Universitat Polit`ecnica de Catalunya, and the CSIC, from Spain., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance and degradation of Proton Exchange Membrane Fuel Cells: State of the art in modeling from atomistic to system scale

  • Jahnke, T.
  • Franco, Alejandro A.
  • Strahl, Stephan
  • Serra-Prat, María
  • Mayur, Manik
  • Bessler, Wolfgang G.
  • Kompis, C.
Jahnke, T. et al., Proton Exchange Membrane Fuel Cells (PEMFC) are energy efficient and environmentally friendly alternatives to conventional energy conversion systems in many yet emerging applications. In order to enable prediction of their performance and durability, it is crucial to gain a deeper understanding of the relevant operation phenomena, e.g., electrochemistry, transport phenomena, thermodynamics as well as the mechanisms leading to the degradation of cell components. Achieving the goal of providing predictive tools to model PEMFC performance, durability and degradation is a challenging task requiring the development of detailed and realistic models reaching from the atomic/molecular scale over the meso scale of structures and materials up to components, stack and system level. In addition an appropriate way of coupling the different scales is required. This review provides a comprehensive overview of the state of the art in modeling of PEMFC, covering all relevant scales from atomistic up to system level as well as the coupling between these scales. Furthermore, it focuses on the modeling of PEMFC degradation mechanisms and on the coupling between performance and degradation models., The research leading to this review has been partially supported by the European Union's Seventh Framework Program for the Fuel Cells and Hydrogen Joint Technology Initiative under the project PUMA MIND (grant agreement no 303419)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fault-tolerant unfalsified control for PEM fuel cell systems

  • Bianchi, Fernando D.
  • Ocampo-Martínez, Carlos
  • Kunusch, Cristian
  • Sánchez-Peña, Ricardo S.
This paper addresses the implementation of a data-driven control strategy in a real test bench based on proton exchange membrane fuel cells (PEMFCs). The proposed control scheme is based on unfalsified control, which allows adapting in real time the control law by evaluating the performance specifications based only on measured input-output data. This approach is especially suitable to deal with nonlinearity, model uncertainty, and also possible faults that may occur in PEMFCs. The control strategy has been applied to several experimental practical situations in order to evaluate not only the system performance, but also different fault scenarios. The experimental results have shown the effectiveness of the proposed approach to regulate the oxygen stoichiometry in real-time operation, as well as to maintain a proper system performance under fault situations. Also, a start-up mass-flow controller is added in order to bring the system toward its normal operating conditions., The research of C. Ocampo-Martinez and C. Kunusch has been supported by the project MACPERCON (Ref. 201250E027) of the CSIC. The research of C. Kunusch has been also supported by the 7th Framework Programme of the EU through the Marie Curie actions (GA: PCIG09-GA-2011-293876) and Puma-Mind project (GA: FCH-JU-2011-1-303419), as well as by the CICYT project DPI2011-25649 (MICINN-Spain). The research of R.S. S´anchez Peña has been supported by CONICET and grant PICT2008-290 from the PRH Program of the Ministry of Science, Technology and Innovation of Argentina., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nonlinear distributed parameter observer design for fuel cell systems

  • Luna, Julio
  • Husar, Attila
  • Serra-Prat, María
This paper presents the development of a nonlinear state observer to estimate the different gas species concentration profiles in a Proton Exchange Membrane Fuel Cell energy system. The selection of the estimated states follows functionality and fuel cell performance criteria. The implementation is based on the finite element discretisation of a fuel cell distributed parameter model. Forward and backwards discretisation of the partial derivative equations is performed to take advantage of the boundary conditions of the problem and also to apply lumped systems theory in the synthesis procedure of the observer. A second-order sliding-mode super-twisting corrective input action is implemented to reduce the estimation error to zero in a finite amount of time. The sliding-mode control approach grants a suitable corrective action without incrementing the model-dependency of the observer. Simulation results are presented to show the performance of the proposed observer of the fuel cell internal states and to extract conclusions for future research work., This work is partially funded by the Spanish national MICINN project DPI2011-25649, as well as by the 7th Framework Programme of the European Commission in the context of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) through the project PUMA-MIND FP7 303419., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dither-less extremum seeking for hydrogen minimization in PEM fuel cells

  • Castaños, Fernando
  • Kunusch, Cristian
This paper presents a nonsmooth adaptive extremum seeker that minimizes the hydrogen consumption in a fuel-cell system. The extremum seeker operates by estimating the gradient of the objective function but, unlike other seekers, it does not require a dither signal to produce such estimate. The absence of a dither signal simplifies the choice of parameter values for the seeker, and more importantly, it allows it to converge to the optimal value exactly, not only to a small neighborhood. The proper functioning of the proposed scheme is proved using nonsmooth Lyapunov analysis. The strategy is tested on the input-output map of a real polymer electrolyte fuel cell., The research of C. Kunusch has been supported by the Seventh Framework Programme of the European Community through the Marie Curie actions (GA: PCIG09-GA-2011-293876), the Puma-Mind project (GA: FCH-JU-2011-1-303419), the CICYT project DPI2011-25649 (MINECO-Spain), the CSIC MACPERCON project (201250E027) and the CSIC JAE-DOC Research Programme., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A multi-timescale modeling methodology for PEMFC performance and durability in a virtual fuel cell car

  • Mayur, Manik
  • Strahl, Stephan
  • Husar, Attila
  • Bessler, Wolfgang G.
The durability of polymer electrolyte membrane fuel cells (PEMFC) is governed by a nonlinear coupling between system demand, component behavior, and physicochemical degradation mechanisms, occurring on timescales from the sub-second to the thousand-hour. We present a simulation methodology for assessing performance and durability of a PEMFC under automotive driving cycles. The simulation framework consists of (a) a fuel cell car model converting velocity to cell power demand, (b) a 2D multiphysics cell model, (c) a flexible degradation library template that can accommodate physically-based component-wise degradation mechanisms, and (d) a time-upscaling methodology for extrapolating degradation during a representative load cycle to multiple cycles. The computational framework describes three different time scales, (1) sub-second timescale of electrochemistry, (2) minute-timescale of driving cycles, and (3) thousand-hour-timescale of cell ageing. We demonstrate an exemplary PEMFC durability analysis due to membrane degradation under a highly transient loading of the New European Driving Cycle (NEDC)., The research leading to this work has been supported by the European Union's Seventh Framework Program for the Fuel Cells and Hydrogen Joint Technology Initiative under the project PUMA MIND (grant agreement no 303419)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nonlinear observation in fuel cell systems: A comparison between disturbance estimation and High-Order Sliding-Mode techniques

  • Luna, Julio
  • Usai, Elio
  • Husar, Attila
  • Serra-Prat, María
This paper compares two Nonlinear Distributed Parameter Observers (NDPO) for the observation of a Proton Exchange Membrane Fuel Cell (PEMFC). Both NDPOs are based on the discretisation of distributed parameters models and they are used to estimate the state profile of gas concentrations in the anode and cathode gas channels of the PEMFC, giving detailed information about the internal conditions of the system. The reaction and water transport flow rates from the membrane to the channels are uncertainties of the observation problem and they are estimated throughout all the length of the PEMFC without the use of additional sensors. The first observation approach is a Nonlinear Disturbance Observer (NDOB) for the estimation of the disturbances in the NDPO. In the second approach, a novel implementation of a High-Order Sliding-Mode (HOSM) observer is developed to estimate the true value of the states as well as the reaction terms. The proposed observers are tested and compared through a simulation example at different operating points and their performance and robustness is analysed over a given case study, the New European Driving Cycle., This work has been partially funded by the Spanish national project MICAPEM (ref. DPI2015-69286-C3-2R), the Regione Autonoma della Sardegna projectCRP-7733 and the European project PUMA-MIND (ref. SPI-JTI-FCH 303419)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nonlinear predictive control for durability enhancement and efficiency improvement in a fuel cell power system

  • Luna, Julio
  • Jemei, Samir
  • Yousfi-Steiner, Nadia
  • Husar, Attila
  • Serra-Prat, María
  • Hissel, Daniel
In this work, a nonlinear model predictive control (NMPC) strategy is proposed to improve the efficiency and enhance the durability of a proton exchange membrane fuel cell (PEMFC) power system. The PEMFC controller is based on a distributed parameters model that describes the nonlinear dynamics of the system, considering spatial variations along the gas channels. Parasitic power from different system auxiliaries is considered, including the main parasitic losses which are those of the compressor. A nonlinear observer is implemented, based on the discretised model of the PEMFC, to estimate the internal states. This information is included in the cost function of the controller to enhance the durability of the system by means of avoiding local starvation and inappropriate water vapour concentrations. Simulation results are presented to show the performance of the proposed controller over a given case study in an automotive application (New European Driving Cycle). With the aim of representing the most relevant phenomena that affects the PEMFC voltage, the simulation model includes a two-phase water model and the effects of liquid water on the catalyst active area. The control model is a simplified version that does not consider two-phase water dynamics., This work has been partially funded by the Spanish national project MICAPEM (ref. DPI2015-69286-C3-2-R, MINECO/FEDER), the LABEX ACTION (ref. ANR-11-LABX-01-01) and the European project PUMA-MIND (ref. SPI-JTI-FCH 303419)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fast prediction of adsorption properties for platinum nanocatalysts with generalized coordination numbers

  • Calle-Vallejo, Federico
  • Martínez, José I.
  • García-Lastra, J. M.
  • Sautet, Philippe
  • Loffreda, David
Platinum is a prominent catalyst for a multiplicity of reactions because of its high activity and stability. As Pt nanoparticles are normally used to maximize catalyst utilization and to minimize catalyst loading, it is important to rationalize and predict catalytic activity trends in nanoparticles in simple terms, while being able to compare these trends with those of extended surfaces. The trends in the adsorption energies of small oxygen- and hydrogen-containing adsorbates on Pt nanoparticles of various sizes and on extended surfaces were analyzed through DFT calculations by making use of the generalized coordination numbers of the surface sites. This simple and predictive descriptor links the geometric arrangement of a surface to its adsorption properties. It generates linear adsorption-energy trends, captures finite-size effects, and provides more accurate descriptions than d-band centers and usual coordination numbers. Unlike electronic-structure descriptors, which require knowledge of the densities of states, it is calculated manually. Finally, it was shown that an approximate equivalence exists between generalized coordination numbers and d-band centers., F.C.V., P.S., and D.L. acknowledge EU funding through the PUMA MIND contract (Call FCH‐JU‐2011‐1, Code SP1‐JTI‐FCH‐2011.1.3, Project 303419). We thank IDRIS and CINES (project 609, GENCI/CT8) and PSMN for CPU time and assistance. J.I.M. acknowledges support from CSIC and ESF through the JAEDoc program. J.M.G.L. acknowledges support from MINECO (FIS2012‐30996) and the ReLiable project funded by the DCSR (11‐116792).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A multi-timescale modeling methodology for PEMFC performance and durability in a virtual fuel cell car

  • Mayur, Manik
  • Strahl, Stephan
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Bessler, Wolfang G.
The durability of polymer electrolyte membrane fuel cells (PEMFC) is governed by a nonlinear cou-pling between system demand, component behavior, and physicochemical degradation mechanisms, occurring on timescales from the sub-second to the thousand-hour. We present a simulation methodol-ogy for assessing performance and durability of a PEMFC under automotive driving cycles. The simu-lation framework consists of (a) a fuel cell car model converting velocity to cell power demand, (b) a 2D multiphysics cell model, (c) a flexible degradation library template that can accommodate physi-cally-based component-wise degradation mechanisms, and (d) a time-upscaling methodology for ex-trapolating degradation during a representative load cycle to multiple cycles. The computational framework describes three different time scales, (1) sub-second timescale of electrochemistry, (2) minute-timescale of driving cycles, and (3) thousand-hour-timescale of cell ageing. We demonstrate an exemplary PEMFC durability analysis due to membrane degradation under a highly transient load-ing of the New European Driving Cycle (NEDC)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Fault-tolerant unfalsified control for PEM fuel cell systems

  • Bianchi, Fernando Daniel|||0000-0001-7332-6501
  • Ocampo-Martínez, Carlos|||0000-0001-9251-6044
  • Kunusch, Cristian
  • Sánchez Peña, Ricardo Salvador
The article addresses the implementation of a data-driven control strategy in a real test bench based on proton exchange membrane fuel cells (PEMFCs). The proposed control scheme is based on Unfalsified Control (UC), which allows adapting in real-time the control law by evaluating the performance specifications based only on measured input-output data. This approach is especially suitable to deal with non-linearity, model uncertainty and also possible faults that may occur in PEMFCs. The control strategy has been applied to several experimental practical situations in order to evaluate not only the system performance but also different fault scenarios. The experimental results have shown the effectiveness of the proposed approach to regulate the oxygen stoichiometry in real-time operation as well as to maintain a proper system performance under fault situations. Also, a start-up mass-flow controller is added in order to bring the system towards its normal operating conditions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Ditherless extremum seeking for hydrogen minimization in PEM fuel cells

  • Castaños Luna, Fernando
  • Kunusch, Cristian
This paper presents a nonsmooth adaptive extremum seeker that minimizes the hydrogen consumption in a fuel-cell system. The extremum seeker operates by estimating the gradient of the objective function but, unlike other seekers, it does not require a dither signal to produce such estimate. The absence of a dither signal simplifies the choice of parameter values for the seeker, and more importantly, it allows it to converge to the optimal value exactly, not only to a small neighborhood. The proper functioning of the proposed scheme is proved using non-smooth Lyapunov analysis. The strategy is tested on the input–output map of a real polymer electrolyte fuel cells., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nonlinear observation in fuel cell systems: a comparison between disturbance estimation and High-Order Sliding-Mode techniques

  • Luna Pacho, Julio Alberto
  • Usai, Elio
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Serra, Maria|||0000-0002-9885-8093
© <year>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper compares two Nonlinear Distributed Parameter Observers (NDPO) for the observation of a Proton Exchange Membrane Fuel Cell (PEMFC). Both NDPOs are based on the discretisation of distributed parameters models and they are used to estimate the state profile of gas concentrations in the anode and cathode gas channels of the PEMFC, giving detailed information about the internal conditions of the system. The reaction and water transport flow rates from the membrane to the channels are uncertainties of the observation problem and they are estimated throughout all the length of the PEMFC without the use of additional sensors. The first observation approach is a Nonlinear Disturbance Observer (NDOB) for the estimation of the disturbances in the NDPO. In the second approach, a novel implementation of a High-Order Sliding-Mode (HOSM) observer is developed to estimate the true value of the states as well as the reaction terms. The proposed observers are tested and compared through a simulation example at different operating points and their performance and robustness is analysed over a given case study, the New European Driving Cycle., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Performance improvement by temperature control of an open-cathode PEM fuel cell system

  • Strahl, Stephan
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Puleston, Paul Federico
  • Riera, Jordi (Riera Colomer)
The work presented in this article combines experimental analysis and theoretical studies of temperature effects on the performance of an open-cathode, self-humidified PEM fuel cell system for the design of optimal control strategies. The experimental analysis shows the great potential of improving the system performance by proper thermal management. The most significant temperature dependent parameter of the system under study is the exchange current density. On the one hand it is influenced positively by a temperature increase as this lowers the activation barrier. On the other hand a higher temperature causes a reduction of the electrochemical active sites in the cathode catalyst layer due to lower water content in the ionomer and primary pores. Dynamic models for fuel cell temperature, liquid water transport and the related electrochemistry have been developed and validated against the experiment. A cascaded Extremum Seeking control algorithm with a local PI controller is proposed to regulate the temperature to a fuel cell voltage maximum. However, the slow dynamics of the temperature related catalyst-drying effect on performance complicate the optimal thermal management with model-free control strategies., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Development and implementation of a supervisor strategy and sliding mode control setup for fuel-cell-based hybrid generation systems

  • More, Jerónimo Jose
  • Puleston, Paul Federico
  • Kunusch, Cristian
  • Allué Fantova, Miguel
© 20xx IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents the development and experimental results of a supervisor strategy and a sliding mode control setup to improve the performance of hybrid generation systems. The topology in this study is conformed by a core comprising a fuel cell module and a supercapacitor module, in combination with an alternative energy source module and an electrolyzer. In particular, a wind power turbine is considered as alternative power source to attain a hybrid generation system fully relying on renewable energy. First, a supervisor strategy is proposed to manage the power flows of the subsystems and coordinate the system as a whole. Subsequently, a sliding mode control setup for combined operation of the dc/dc power converters of the fuel cell/supercapacitor core is presented to track the power references synthesized by the supervisor control. Both control levels, supervisor strategy and sliding mode controllers, are implemented and assessed through extensive experimental tests under different wind conditions and heavy-load changes., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Experimental study of hydrogen purge effects on performance and efficiency of an open-cathode proton exchange membrane fuel cell system

  • Strahl, Stephan
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Riera, Jordi (Riera Colomer)
The performance and efficiency of an open-cathode PEM fuel cell system in dead-ended anode (DEA) configuration and hydrogen purges is analyzed in this work. Excess water and crossed-over nitrogen in the anode decrease the hydrogen concentration at the catalyst surface, which in turn causes performance losses. Purging the anode with hydrogen removes water and nitrogen and thus recovers the performance. However, this means wasting hydrogen and decreasing overall system efficiency. Gas chromatography was used to detect and quantify the accumulated nitrogen in the anode during DEA operation. The experiments show that the major performance limitation in the studied system is related to water instead of nitrogen. Moreover, oxygen was detected in the anode exhaust gas after long purge intervals, which is an indicator for corrosion of the cathode carbon support structure. Experimental observations revealed that the need for a hydrogen purge strongly depends on the operating conditions and the state-of-health of the fuel cell. It is shown that flooding on the anode and drying of the cathode catalyst layer may occur simultaneously during purged operation. Therefore, purge decisions must be evaluated online, depending on the operating conditions., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nonlinear distributed parameter observer design for fuel cell systems

  • Luna Pacho, Julio Alberto
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Serra, Maria|||0000-0002-9885-8093
This paper presents the development of a nonlinear state observer to estimate the different gas species concentration profiles in a Proton Exchange Membrane Fuel Cell energy system. The selection of the estimated states follows functionality and fuel cell performance criteria. The implementation is based on the finite element discretisation of a fuel cell distributed parameter model. Forward and backwards discretisation of the partial derivative equations is performed to take advantage of the boundary conditions of the problem and also to apply lumped systems theory in the synthesis procedure of the observer. A second-order sliding-mode super-twisting corrective input action is implemented to reduce the estimation error to zero in a finite amount of time. The sliding-mode control approach grants a suitable corrective action without incrementing the model-dependency of the observer. Simulation results are presented to show the performance of the proposed observer of the fuel cell internal states and to extract conclusions for future research work., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Distributed parameter model simulation tool for PEM fuel cells

  • Sarmiento Carnevali, María Laura
  • Serra, Maria|||0000-0002-9885-8093
  • Batlle Arnau, Carles|||0000-0002-6088-6187
In this work, a simulation tool for proton exchange membrane fuel cells (PEMFC) has been developed, based on a distributed parameter model. The tool is designed to perform studies of time and space variations in the direction of the gas channels. Results for steady-state and dynamic simulations for a single cell of one channel are presented and analyzed. Considered variables are concentrations of reactants, pressures, temperatures, humidification, membrane water content, current density, among others that have significant effects on the performance and durability of PEMFC. Copyright (C) 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Control-oriented thermal modeling methodology for water-cooled PEM fuel-cell-based systems

  • Rojas Fernández, José David
  • Kunusch, Cristian
  • Ocampo-Martínez, Carlos|||0000-0001-9251-6044
  • Puig Cayuela, Vicenç|||0000-0002-6364-6429
In this paper, a new control-oriented modeling methodology for the thermal dynamics of water-cooled Proton Exchange Membrane Fuel Cells (PEMFCs) is presented and validated. This methodology is not only useful for control applications, but also can be used for predicting the temperature variation across the stack, allowing to monitor its operation. The methodology has been validated in a real 600-W, 20-cells, water cooled PEMFC, with encouraging results for both the stationary and the transient states. Results show that the proposed methodology is accurate and suitable for control purposes., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Performance and degradation of proton exchange membrane fuel cells: State of the art in modeling from atomistic to system scale

  • Jahnke, T.
  • Futter, G.
  • Latz, A.
  • Serra, Maria|||0000-0002-9885-8093
Proton Exchange Membrane Fuel Cells (PEMFC) are energy efficient and environmentally friendly alternatives to conventional energy conversion systems in many yet emerging applications. In order to enable prediction of their performance and durability, it is crucial to gain a deeper understanding of the relevant operation phenomena, e.g., electrochemistry, transport phenomena, thermodynamics as well as the mechanisms leading to the degradation of cell components. Achieving the goal of providing predictive tools to model PEMFC performance, durability and degradation is a challenging task requiring the development of detailed and realistic models reaching from the atomic/molecular scale over the meso scale of structures and materials up to components, stack and system level. In addition an appropriate way of coupling the different scales is required.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

A gain-scheduled LPV control for oxygen stoichiometry regulation in PEM fuel cell systems

  • Bianchi, Fernando Daniel|||0000-0001-7332-6501
  • Kunusch, Cristian
  • Ocampo-Martínez, Carlos|||0000-0001-9251-6044
  • Sánchez Peña, Ricardo Salvador
The article addresses the LPV control of a Polymer Electrolyte Membrane Fuel Cell (PEMFC). In order to optimize efficiency, PEMFCs require reliable control systems ensuring stability and performance, as well as robustness to model uncertainties and external perturbations. On the other hand, PEMFCs present a highly nonlinear behavior that demands nonlinear and/or adaptive control strategies to achieve high performance in the entire operating range. Here, a linear parameter varying (LPV) gain scheduled control is proposed. The control is based on a piecewise affine LPV representation of the PEMFC, a model that can be available in practice. In order to deal with the saturation of the control action, an LPV anti-windup compensation is also proposed. The complete control strategy is applied to several experimental practical situations in a laboratory fuel cell system to evaluate its performance and the reliability of the proposed algorithms., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Experimental analysis of a degraded open-cathode PEM fuel cell stack

  • Strahl, Stephan
  • Gasamans Rodríguez, Noemí
  • Llorca Piqué, Jordi|||0000-0002-7447-9582
  • Husar, Attila Peter|||0000-0001-8503-3837
The well-known challenges to overcome in PEM fuel cell research are their relatively low durability and the high costs for the platinum catalysts. This work focuses on degradation mechanisms that are present in open-cathode PEM fuel cell systems and their links to the decaying fuel cell performance. Therefore a degraded, open-cathode, 20 cell, PEM fuel cell stack was analyzed by means of in-situ and ex-situ techniques. Voltage transients during external perturbations, such as changing temperature, humidity and stoichiometry show that degradation affects individual cells quite differently towards the end of life of the stack. Cells located close to the endplates of the stack show the biggest performance decay. Electrochemical impedance spectroscopy (EIS) data present non-reversible catalyst layer degradation but negligible membrane degradation of several cells. Post-mortem, ex-situ experiments, such as cyclic voltammetry (CV), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) show a significant active area loss of the first cells within the stack due to Pt dissolution, oxidation and agglomeration. Scanning electron microscope (SEM) images of the degraded cells in comparison with the normally working cells in the stack show severe carbon corrosion of the cathode catalyst layers., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Nonlinear predictive control for durability enhancement and efficiency improvement in a fuel cell power system

  • Luna Pacho, Julio Alberto
  • Jemei, Samir
  • Yousfi-Steiner, Nadia
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Serra, Maria|||0000-0002-9885-8093
  • Hissel, Daniel
© <year>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In this work, a nonlinear model predictive control (NMPC) strategy is proposed to improve the efficiency and enhance the durability of a proton exchange membrane fuel cell (PEMFC) power system. The PEMFC controller is based on a distributed parameters model that describes the nonlinear dynamics of the system, considering spatial variations along the gas channels. Parasitic power from different system auxiliaries is considered, including the main parasitic losses which are those of the compressor. A nonlinear observer is implemented, based on the discretised model of the PEMFC, to estimate the internal states. This information is included in the cost function of the controller to enhance the durability of the system by means of avoiding local starvation and inappropriate water vapour concentrations. Simulation results are presented to show the performance of the proposed controller over a given case study in an automotive application (New European Driving Cycle). With the aim of representing the most relevant phenomena that affects the PEMFC voltage, the simulation model includes a two-phase water model and the effects of liquid water on the catalyst active area. The control model is a simplified version that does not consider two-phase water dynamics., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Electrode structure effects on the performance of open-cathode proton exchange membrane fuel cells: A multiscale modeling approach

  • Strahl, Stephan
  • Husar, Attila Peter|||0000-0001-8503-3837
  • Franco, Alejandro A.
In this paper we present a new dynamic multiscale model of an open-cathode Polymer Electrolyte Membrane Fuel Cell (PEMFC). The model describes two-phase water transport, electrochemistry and thermal management within a framework that combines a Computational Fluid Dynamics (CFD) approach with a micro-structurally-resolved model predicting the water filling dynamics of the electrode pores and the impact of these dynamics on the evolution of the electrochemically active surface area (ECSA). The model allows relating for the first time the cathode electrode structure to the cell voltage transient behavior during experimental changes in fuel cell temperature. The effect of evaporation rates, desorption rates and temperature changes on the performance of four different electrode pore size distributions are explored using steady-state and transient numerical simulations. The results are discussed with respect to water management and temperature control. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nonlinear observation in fuel cell systems: a comparison between disturbance estimation and High-Order Sliding-Mode techniques

  • Luna Pacho, Julio Alberto
  • Usai, Elio
  • Husar, Attila Peter
  • Serra, Maria
© <year>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, This paper compares two Nonlinear Distributed Parameter Observers (NDPO) for the observation of a Proton Exchange Membrane Fuel Cell (PEMFC). Both NDPOs are based on the discretisation of distributed parameters models and they are used to estimate the state profile of gas concentrations in the anode and cathode gas channels of the PEMFC, giving detailed information about the internal conditions of the system. The reaction and water transport flow rates from the membrane to the channels are uncertainties of the observation problem and they are estimated throughout all the length of the PEMFC without the use of additional sensors. The first observation approach is a Nonlinear Disturbance Observer (NDOB) for the estimation of the disturbances in the NDPO. In the second approach, a novel implementation of a High-Order Sliding-Mode (HOSM) observer is developed to estimate the true value of the states as well as the reaction terms. The proposed observers are tested and compared through a simulation example at different operating points and their performance and robustness is analysed over a given case study, the New European Driving Cycle., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Performance improvement by temperature control of an open-cathode PEM fuel cell system

  • Strahl, Stephan
  • Husar, Attila Peter
  • Puleston, Paul Federico
  • Riera, Jordi (Riera Colomer)
The work presented in this article combines experimental analysis and theoretical studies of temperature effects on the performance of an open-cathode, self-humidified PEM fuel cell system for the design of optimal control strategies. The experimental analysis shows the great potential of improving the system performance by proper thermal management. The most significant temperature dependent parameter of the system under study is the exchange current density. On the one hand it is influenced positively by a temperature increase as this lowers the activation barrier. On the other hand a higher temperature causes a reduction of the electrochemical active sites in the cathode catalyst layer due to lower water content in the ionomer and primary pores. Dynamic models for fuel cell temperature, liquid water transport and the related electrochemistry have been developed and validated against the experiment. A cascaded Extremum Seeking control algorithm with a local PI controller is proposed to regulate the temperature to a fuel cell voltage maximum. However, the slow dynamics of the temperature related catalyst-drying effect on performance complicate the optimal thermal management with model-free control strategies., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nonlinear distributed parameter observer design for fuel cell systems

  • Luna Pacho, Julio Alberto
  • Husar, Attila Peter
  • Serra, Maria
This paper presents the development of a nonlinear state observer to estimate the different gas species concentration profiles in a Proton Exchange Membrane Fuel Cell energy system. The selection of the estimated states follows functionality and fuel cell performance criteria. The implementation is based on the finite element discretisation of a fuel cell distributed parameter model. Forward and backwards discretisation of the partial derivative equations is performed to take advantage of the boundary conditions of the problem and also to apply lumped systems theory in the synthesis procedure of the observer. A second-order sliding-mode super-twisting corrective input action is implemented to reduce the estimation error to zero in a finite amount of time. The sliding-mode control approach grants a suitable corrective action without incrementing the model-dependency of the observer. Simulation results are presented to show the performance of the proposed observer of the fuel cell internal states and to extract conclusions for future research work., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental analysis of a degraded open-cathode PEM fuel cell stack

  • Strahl, Stephan
  • Gasamans Rodríguez, Noemí
  • Llorca Piqué, Jordi
  • Husar, Attila Peter
The well-known challenges to overcome in PEM fuel cell research are their relatively low durability and the high costs for the platinum catalysts. This work focuses on degradation mechanisms that are present in open-cathode PEM fuel cell systems and their links to the decaying fuel cell performance. Therefore a degraded, open-cathode, 20 cell, PEM fuel cell stack was analyzed by means of in-situ and ex-situ techniques. Voltage transients during external perturbations, such as changing temperature, humidity and stoichiometry show that degradation affects individual cells quite differently towards the end of life of the stack. Cells located close to the endplates of the stack show the biggest performance decay. Electrochemical impedance spectroscopy (EIS) data present non-reversible catalyst layer degradation but negligible membrane degradation of several cells. Post-mortem, ex-situ experiments, such as cyclic voltammetry (CV), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) show a significant active area loss of the first cells within the stack due to Pt dissolution, oxidation and agglomeration. Scanning electron microscope (SEM) images of the degraded cells in comparison with the normally working cells in the stack show severe carbon corrosion of the cathode catalyst layers., Peer Reviewed, Preprint
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Distributed parameter model simulation tool for PEM fuel cells

  • Sarmiento Carnevali, María Laura
  • Serra, Maria
  • Batlle Arnau, Carles
In this work, a simulation tool for proton exchange membrane fuel cells (PEMFC) has been developed, based on a distributed parameter model. The tool is designed to perform studies of time and space variations in the direction of the gas channels. Results for steady-state and dynamic simulations for a single cell of one channel are presented and analyzed. Considered variables are concentrations of reactants, pressures, temperatures, humidification, membrane water content, current density, among others that have significant effects on the performance and durability of PEMFC. Copyright (C) 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Fault-tolerant unfalsified control for PEM fuel cell systems

  • Bianchi, Fernando Daniel
  • Ocampo-Martínez, Carlos
  • Kunusch, Cristian
  • Sánchez Peña, Ricardo Salvador
The article addresses the implementation of a data-driven control strategy in a real test bench based on proton exchange membrane fuel cells (PEMFCs). The proposed control scheme is based on Unfalsified Control (UC), which allows adapting in real-time the control law by evaluating the performance specifications based only on measured input-output data. This approach is especially suitable to deal with non-linearity, model uncertainty and also possible faults that may occur in PEMFCs. The control strategy has been applied to several experimental practical situations in order to evaluate not only the system performance but also different fault scenarios. The experimental results have shown the effectiveness of the proposed approach to regulate the oxygen stoichiometry in real-time operation as well as to maintain a proper system performance under fault situations. Also, a start-up mass-flow controller is added in order to bring the system towards its normal operating conditions., Peer Reviewed, Postprint (author’s final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A gain-scheduled LPV control for oxygen stoichiometry regulation in PEM fuel cell systems

  • Bianchi, Fernando Daniel
  • Kunusch, Cristian
  • Ocampo-Martínez, Carlos
  • Sánchez Peña, Ricardo Salvador
The article addresses the LPV control of a Polymer Electrolyte Membrane Fuel Cell (PEMFC). In order to optimize efficiency, PEMFCs require reliable control systems ensuring stability and performance, as well as robustness to model uncertainties and external perturbations. On the other hand, PEMFCs present a highly nonlinear behavior that demands nonlinear and/or adaptive control strategies to achieve high performance in the entire operating range. Here, a linear parameter varying (LPV) gain scheduled control is proposed. The control is based on a piecewise affine LPV representation of the PEMFC, a model that can be available in practice. In order to deal with the saturation of the control action, an LPV anti-windup compensation is also proposed. The complete control strategy is applied to several experimental practical situations in a laboratory fuel cell system to evaluate its performance and the reliability of the proposed algorithms., Peer Reviewed, Postprint (author’s final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Electrode structure effects on the performance of open-cathode proton exchange membrane fuel cells: A multiscale modeling approach

  • Strahl, Stephan
  • Husar, Attila Peter
  • Franco, Alejandro A.
In this paper we present a new dynamic multiscale model of an open-cathode Polymer Electrolyte Membrane Fuel Cell (PEMFC). The model describes two-phase water transport, electrochemistry and thermal management within a framework that combines a Computational Fluid Dynamics (CFD) approach with a micro-structurally-resolved model predicting the water filling dynamics of the electrode pores and the impact of these dynamics on the evolution of the electrochemically active surface area (ECSA). The model allows relating for the first time the cathode electrode structure to the cell voltage transient behavior during experimental changes in fuel cell temperature. The effect of evaporation rates, desorption rates and temperature changes on the performance of four different electrode pore size distributions are explored using steady-state and transient numerical simulations. The results are discussed with respect to water management and temperature control. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Control-oriented thermal modeling methodology for water-cooled PEM fuel-cell-based systems

  • Rojas Fernández, José David
  • Kunusch, Cristian
  • Ocampo-Martínez, Carlos
  • Puig Cayuela, Vicenç
In this paper, a new control-oriented modeling methodology for the thermal dynamics of water-cooled Proton Exchange Membrane Fuel Cells (PEMFCs) is presented and validated. This methodology is not only useful for control applications, but also can be used for predicting the temperature variation across the stack, allowing to monitor its operation. The methodology has been validated in a real 600-W, 20-cells, water cooled PEMFC, with encouraging results for both the stationary and the transient states. Results show that the proposed methodology is accurate and suitable for control purposes., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Development and implementation of a supervisor strategy and sliding mode control setup for fuel-cell-based hybrid generation systems

  • More, Jerónimo Jose
  • Puleston, Paul Federico
  • Kunusch, Cristian
  • Allué Fantova, Miguel
© 20xx IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents the development and experimental results of a supervisor strategy and a sliding mode control setup to improve the performance of hybrid generation systems. The topology in this study is conformed by a core comprising a fuel cell module and a supercapacitor module, in combination with an alternative energy source module and an electrolyzer. In particular, a wind power turbine is considered as alternative power source to attain a hybrid generation system fully relying on renewable energy. First, a supervisor strategy is proposed to manage the power flows of the subsystems and coordinate the system as a whole. Subsequently, a sliding mode control setup for combined operation of the dc/dc power converters of the fuel cell/supercapacitor core is presented to track the power references synthesized by the supervisor control. Both control levels, supervisor strategy and sliding mode controllers, are implemented and assessed through extensive experimental tests under different wind conditions and heavy-load changes., Peer Reviewed, Postprint (author’s final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

A multi-timescale modeling methodology for PEMFC performance and durability in a virtual fuel cell car

  • Mayur, Manik
  • Strahl, Stephan
  • Husar, Attila Peter
  • Bessler, Wolfang G.
The durability of polymer electrolyte membrane fuel cells (PEMFC) is governed by a nonlinear cou-pling between system demand, component behavior, and physicochemical degradation mechanisms, occurring on timescales from the sub-second to the thousand-hour. We present a simulation methodol-ogy for assessing performance and durability of a PEMFC under automotive driving cycles. The simu-lation framework consists of (a) a fuel cell car model converting velocity to cell power demand, (b) a 2D multiphysics cell model, (c) a flexible degradation library template that can accommodate physi-cally-based component-wise degradation mechanisms, and (d) a time-upscaling methodology for ex-trapolating degradation during a representative load cycle to multiple cycles. The computational framework describes three different time scales, (1) sub-second timescale of electrochemistry, (2) minute-timescale of driving cycles, and (3) thousand-hour-timescale of cell ageing. We demonstrate an exemplary PEMFC durability analysis due to membrane degradation under a highly transient load-ing of the New European Driving Cycle (NEDC)., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Ditherless extremum seeking for hydrogen minimization in PEM fuel cells

  • Castaños Luna, Fernando
  • Kunusch, Cristian
This paper presents a nonsmooth adaptive extremum seeker that minimizes the hydrogen consumption in a fuel-cell system. The extremum seeker operates by estimating the gradient of the objective function but, unlike other seekers, it does not require a dither signal to produce such estimate. The absence of a dither signal simplifies the choice of parameter values for the seeker, and more importantly, it allows it to converge to the optimal value exactly, not only to a small neighborhood. The proper functioning of the proposed scheme is proved using non-smooth Lyapunov analysis. The strategy is tested on the input–output map of a real polymer electrolyte fuel cells., Peer Reviewed, Postprint (author’s final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Experimental study of hydrogen purge effects on performance and efficiency of an open-cathode proton exchange membrane fuel cell system

  • Strahl, Stephan
  • Husar, Attila Peter
  • Riera, Jordi (Riera Colomer)
The performance and efficiency of an open-cathode PEM fuel cell system in dead-ended anode (DEA) configuration and hydrogen purges is analyzed in this work. Excess water and crossed-over nitrogen in the anode decrease the hydrogen concentration at the catalyst surface, which in turn causes performance losses. Purging the anode with hydrogen removes water and nitrogen and thus recovers the performance. However, this means wasting hydrogen and decreasing overall system efficiency. Gas chromatography was used to detect and quantify the accumulated nitrogen in the anode during DEA operation. The experiments show that the major performance limitation in the studied system is related to water instead of nitrogen. Moreover, oxygen was detected in the anode exhaust gas after long purge intervals, which is an indicator for corrosion of the cathode carbon support structure. Experimental observations revealed that the need for a hydrogen purge strongly depends on the operating conditions and the state-of-health of the fuel cell. It is shown that flooding on the anode and drying of the cathode catalyst layer may occur simultaneously during purged operation. Therefore, purge decisions must be evaluated online, depending on the operating conditions., Peer Reviewed, Preprint
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Performance and degradation of proton exchange membrane fuel cells: State of the art in modeling from atomistic to system scale

  • Jahnke, T.
  • Futter, G.
  • Latz, A.
  • Serra, Maria
Proton Exchange Membrane Fuel Cells (PEMFC) are energy efficient and environmentally friendly alternatives to conventional energy conversion systems in many yet emerging applications. In order to enable prediction of their performance and durability, it is crucial to gain a deeper understanding of the relevant operation phenomena, e.g., electrochemistry, transport phenomena, thermodynamics as well as the mechanisms leading to the degradation of cell components. Achieving the goal of providing predictive tools to model PEMFC performance, durability and degradation is a challenging task requiring the development of detailed and realistic models reaching from the atomic/molecular scale over the meso scale of structures and materials up to components, stack and system level. In addition an appropriate way of coupling the different scales is required., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Nonlinear predictive control for durability enhancement and efficiency improvement in a fuel cell power system

  • Luna Pacho, Julio Alberto
  • Jemei, Samir
  • Yousfi-Steiner, Nadia
  • Husar, Attila Peter
  • Serra, Maria
  • Hissel, Daniel
© <year>. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/, In this work, a nonlinear model predictive control (NMPC) strategy is proposed to improve the efficiency and enhance the durability of a proton exchange membrane fuel cell (PEMFC) power system. The PEMFC controller is based on a distributed parameters model that describes the nonlinear dynamics of the system, considering spatial variations along the gas channels. Parasitic power from different system auxiliaries is considered, including the main parasitic losses which are those of the compressor. A nonlinear observer is implemented, based on the discretised model of the PEMFC, to estimate the internal states. This information is included in the cost function of the controller to enhance the durability of the system by means of avoiding local starvation and inappropriate water vapour concentrations. Simulation results are presented to show the performance of the proposed controller over a given case study in an automotive application (New European Driving Cycle). With the aim of representing the most relevant phenomena that affects the PEMFC voltage, the simulation model includes a two-phase water model and the effects of liquid water on the catalyst active area. The control model is a simplified version that does not consider two-phase water dynamics., Peer Reviewed, Postprint (author's final draft)