Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 97
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and Characterization of Environmentally Friendly Insulation Materials for the Building Industry from Olive Pomace Waste

  • Gutierrez, O.
  • Fages, E.
  • Balart, Rafael|||0000-0001-5670-7126
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
[EN] This work is focused on the upgrading olive oil pomace to obtain high environmentally friendly insulation materials for the construction and building industry. Upgrading of these wastes has been carried out by using the wet-laid technology in combination with different thermoplastic binder fibers both from natural and synthetic origin. After the wetlaid process, the obtained veils or non-wovens were subjected to different processes: a hot-press moulding process or a continuous lamination process. The acoustic insulation properties were obtained by the Kundt¿s tube while the thermal insulating properties were obtained through determining heat transmission resistance (R) and heat absorption parameter (¿). These tests have revealed the excellent insulation properties of the olive pomace-derived materials, specifically, those based on high surface density non-wovens. The complementary process that follows wet-laid, i.e. hot-press moulding or continuous lamination process has a remarkable effect on insulation behaviour. In particular, the hot-pressed materials from olive pomace show better acoustic insulation while the continuously laminated materials offer the best thermal insulation properties., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) through the MAT201784909-C2-2-R program number. O. Gutierrez and E. Fages want to thank AITEX (Textile Research Institute) and the Institut Valencia de Competitivitat Empresarial (IVACE) for providing funds and equipment to develop this study within the framework of the ECOMATEX project research and development of technical, functional and sustainable materials applicable to the field of Green Cities (IMAMCI/2016/1). L. Quiles-Carrillo thanks Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). D. Lascano acknowledges UPV for the grant received though the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of Sustainable and Cost-Competitive Injection-Molded Pieces of Partially Bio-Based Polyethylene Terephthalate through the Valorization of Cotton Textile Waste

  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This study presents the valorization of cotton waste from the textile industry for the development of sustainable and cost-competitive biopolymer composites. The as-received linter of recycled cotton was first chopped to obtain short fibers, called recycled cotton fibers (RCFs), which were thereafter melt-compounded in a twin-screw extruder with partially bio-based polyethylene terephthalate (bio-PET) and shaped into pieces by injection molding. It was observed that the incorporation of RCF, in the 1¿10 wt% range, successfully increased rigidity and hardness of bio-PET. However, particularly at the highest fiber contents, the ductility and toughness of the pieces were considerably impaired due to the poor interfacial adhesion of the fibers to the biopolyester matrix. Interestingly, RCF acted as an effective nucleating agent for the bio-PET crystallization and it also increased thermal resistance. In addition, the overall dimensional stability of the pieces was improved as a function of the fiber loading. Therefore, bio-PET pieces containing 3¿5 wt% RCF presented very balanced properties in terms of mechanical strength, toughness, and thermal resistance. The resultant biopolymer composite pieces can be of interest in rigid food packaging and related applications, contributing positively to the optimization of the integrated biorefinery system design and also to the valorization of textile wastes., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) through the AGL2015-63855-C2-1-R and MAT2017-84909-C2-2-R program numbers. L.Q.-C. wants to thank the Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. is a recipient of a Juan de la Cierva Incorporación contract (IJCI-2016-29675) from MICIU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improved Toughness of Polylactide by Binary Blends with Polycarbonate with Glycidyl and Maleic Anhydride-Based Compatibilizers

  • Tejada-Oliveros, Ramon
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Montanes, Nestor|||0000-0001-6070-127X
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] This work reports on the development of polylactide (PLA) and polycarbonate (PC) blends with different compatibilizers with enhanced toughness. Since both polymers are immiscible, two types of compatibilizers are tested: petrochemical-based copolymers Xibond 160 and Xibond 920 with maleic anhydride and epoxy groups, respectively, and natural-based compatibilizers with the same functionalities, namely maleinized linseed oil (MLO) and, epoxidized linseed oil (ELO). Mechanical, thermal, and morphological characterization shows better properties for the PLA/PC (80/20 wt%) blends with chemically modified natural oils (ELO and MLO). The addition of 5 phr (parts per hundred resin) of MLO gives the maximum values for impact strength and elongation at break. Moreover, the glass transition temperature (Tg) slightly decreases with the addition of natural compatibilizers, thus showing some plasticization effect. Petroleum-derived compatibilizers give interesting results regarding tensile strength and stiffness without plasticization. PLA/PC blends show higher thermal stability than neat PLA, regardless of the compatibilizer used, since PC is much more thermally stable than PLA. The obtained results indicate that both petroleum-based and natural-derived compatibilizers positively contribute to enhance the properties of the binary PLA/PC blends. Nevertheless, the results with MLO suggest this is an interesting biobased solution to provide increased toughness to PLA/PC blends., L.Q.-C. wants to thank Universitat Politècnica de València for his postdoctoral PAID-10-20 grant from (SP20200073). J.G.-C. wants to thank Universitat Politècnica de València for his FPI grant from (SP20200080). This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the Use of Gallic Acid as a Potential Natural Antioxidant and Ultraviolet Light Stabilizer in Cast-Extruded Bio-Based High-Density Polyethylene Films

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Sammon, Chris
[Otros] This study originally explores the use of gallic acid (GA) as a natural additive in bio-based high-density polyethylene (bio-HDPE) formulations. Thus, bio-HDPE was first melt-compounded with two different loadings of GA, namely 0.3 and 0.8 parts per hundred resin (phr) of biopolymer, by twin-screw extrusion and thereafter shaped into films using a cast-roll machine. The resultant bio-HDPE films containing GA were characterized in terms of their mechanical, morphological, and thermal performance as well as ultraviolet (UV) light stability to evaluate their potential application in food packaging. The incorporation of 0.3 and 0.8 phr of GA reduced the mechanical ductility and crystallinity of bio-HDPE, but it positively contributed to delaying the onset oxidation temperature (OOT) by 36.5 ºC and nearly 44 ºC, respectively. Moreover, the oxidation induction time (OIT) of bio-HDPE, measured at 210 ºC, was delayed for up to approximately 56 and 240 min, respectively. Furthermore, the UV light stability of the bio-HDPE films was remarkably improved, remaining stable for an exposure time of 10 h even at the lowest GA content. The addition of the natural antioxidant slightly induced a yellow color in the bio-HDPE films and it also reduced their transparency, although a high contact transparency level was maintained. This property can be desirable in some packaging materials for light protection, especially UV radiation, which causes lipid oxidation in food products. Therefore, GA can successfully improve the thermal resistance and UV light stability of green polyolefins and will potentially promote the use of natural additives for sustainable food packaging applications., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. L.Q.-C. wants to thank Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. is the recipient of a Juan de la Cierva contract (IJCI-2016-29675) from MICIU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of the Loading of an Environmentally Friendly Compatibilizer Derived from Linseed Oil in Poly(Lactic Acid)/Diatomaceous Earth Composites

  • Gonzalez, Lucia
  • Agüero, Ángel
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] Maleinized linseed oil (MLO) has been successfully used as biobased compatibilizer in polyester blends. Its effciency as compatibilizer in polymer composites with organic and inorganic fillers, compared to other traditional fillers, has also been proved. The goal of this work is to optimize the amount of MLO on poly(lactic acid)/diatomaceous earth (PLA/DE) composites to open new potential to these materials in the active packaging industry without compromising the environmental effciency of these composites. The amount of DE remains constant at 10 wt% and MLO varies from 1 to 15 phr (weight parts of MLO per 100 g of PLA/DE composite). The e ect of MLO on mechanical, thermal, thermomechanical and morphological properties is described in this work. The obtained results show a clear embrittlement of the uncompatibilized PLA/DE composites, which is progressively reduced by the addition of MLO. MLO shows good miscibility at low concentrations (lower than 5 phr) while above 5 phr, a clear phase separation phenomenon can be detected, with the formation of rounded microvoids and shapes which have a positive e ect on impact strength., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. L. Quiles-Carrillo is recipient of a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD). D. Lascano acknowledges UPV for the grant received though the PAID-01-18 program. N. Montanes acknowledges the project "Development and production of new material from revalued industrial wastes for technological sector applications" for partially funding this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Valorization of Cotton Industry Byproducts in Green Composites with Polylactide

  • Carbonell-Verdu, Alfredo
  • Dominici, Franco
  • Torre, Luigi
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] New sustainable green composites based on polylactide (PLA) and cotton industry byproducts were successfully manufactured by extrusion, and subsequently by conventional injection molding. Cottonseed four was used as reinforcement fller and modifed cottonseed oil (epoxidized and maleinized cottonseed oil, ECSO and MCSO respectively) were used to improve fller-polymer matrix interactions among the interface. Mechanical properties were obtained by standard tensile, fexural, Shore D hardness and impact Charpy tests, while the surface morphology characterization on fractured specimens was carried out by using feld emission scanning electron microscopy. Thermal properties were obtained by diferential scanning calorimetry and the efect of both cottonseed four and chemically-modifed cottonseed oil was evaluated on dynamic mechanical behavior of the obtained composites. Unlike typical lignocellulosic fllers, 15 wt% cottonseed four does not lead to more brittle materials due to stress concentration phenomena. In fact, cottonseed four provides improved toughness and elongation at break (mechanical ductile properties) compared to neat PLA without any other compatibilizer. Addition of both epoxidized and maleinized cottonseed (7.5 wt%) has a positive efect on improving ductile behaviour of composites, thus leading to new green composites with good balance between processability and overall properties. In particular, the impact strength is remarkably improved which plays a key factor in these composites since PLA is, intrinsically, a brittle polymer., This work received funding from the Ministry of Economy and Competitiveness (MINECO) (Grant No. MAT2017-84909-C2-2-R). A. Carbonell-Verdu wants to thank Universitat Politecnica de Valencia for financial support through an FPI grant. L. Quiles-Carrillo wants to thank Spanish Ministry of Education, Culture, and Sports (MECD) for financial support through an FPU Grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Functionalization of Partially Bio-Based Poly(Ethylene Terephthalate) by Blending with Fully Bio-Based Poly(Amide) 10,10 and a Glycidyl Methacrylate-Based Compatibilizer

  • Jorda, Maria
  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Balart, Rafael|||0000-0001-5670-7126
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Montanes, Nestor|||0000-0001-6070-127X
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[Otros] This work shows the potential of binary blends composed of partially bio-based poly(ethyelene terephthalate) (bioPET) and fully bio-based poly(amide) 10,10 (bioPA1010). These blends are manufactured by extrusion and subsequent injection moulding and characterized in terms of mechanical, thermal and thermomechanical properties. To overcome or minimize the immiscibility, a glycidyl methacrylate copolymer, namely poly(styrene-ran-glycidyl methacrylate) (PS-GMA; XibondTM 920) was used. The addition of 30 wt % bioPA provides increased renewable content up to 50 wt %, but the most interesting aspect is that bioPA contributes to improved toughness and other ductile properties such as elongation at yield. The morphology study revealed a typical immiscible droplet-like structure and the effectiveness of the PS-GMA copolymer was assessed by field emission scanning electron microcopy (FESEM) with a clear decrease in the droplet size due to compatibilization. It is possible to conclude that bioPA1010 can positively contribute to reduce the intrinsic sti ness of bioPET and, in addition, it increases the renewable content of the developed materials, This research was funded by the Ministerio de Economía, Industria y Competitividad (MICINN) project number MAT2017-84909-C2-2-R. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). D. Lascano wants to thank UPV for the grant received though the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Pine Resin Derivatives as Sustainable Additives to Improve the Mechanical and Thermal Properties of Injected Moulded Thermoplastic Starch

  • Aldas-Carrasco, Miguel Fernando
  • Arrieta, Marina Patricia
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Fully bio-based materials based on thermoplastic starch (TPS) were developed starting from corn starch plasticized with glycerol. The obtained TPS was further blended with five pine resin derivatives: gum rosin (GR), disproportionated gum rosin (dehydroabietic acid, RD), maleic anhydride modified gum rosin (CM), pentaerythritol ester of gum rosin (LF), and glycerol ester of gum rosin (UG). The TPS¿resin blend formulations were processed by melt extrusion and further by injection moulding to simulate the industrial conditions. The obtained materials were characterized in terms of mechanical, thermal and structural properties. The results showed that all gum rosin-based additives were able to improve the thermal stability of TPS, increasing the degradation onset temperature. The carbonyl groups of gum rosin derivatives were able to interact with the hydroxyl groups of starch and glycerol by means of hydrogen bond interactions producing a significant increase of the glass transition temperature with a consequent stiffening effect, which in turn improve the overall mechanical performance of the TPS-resin injected moulded blends. The developed TPS¿resin blends are of interest for rigid packaging applications., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R) as well as by Santander-UCM (PR87/19-22628) project. M.A. thanks Secretaria Nacional de Educación Superior, Ciencia, Tecnología e Innovación (SENESCYT-Ecuador) and Escuela Politécnica Nacional. C.P. thanks Santiago Grisolía fellowship (GRISOLIAP/2019/113) from Generalitat Valenciana and M.P.A. thanks MINECO for her postdoctoral contract: Juan de la Cierva-Incorporación (FJCI-2017-33536).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

High toughness poly (lactic acid) (PLA) formulations obtained by ternary blends with poly (3-hydroxybutyrate) (PHB) and flexible polyesters from succinic acid

  • GARCÍA CAMPO, MARÍA JESÚS
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Balart, Rafael|||0000-0001-5670-7126
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This work reports the development of poly(lactic acid) (PLA) formulations with improved toughness by ternary blends with poly(3-hydroxybutyrate) (PHB) and two different flexible polyesters derived from succinic acid, namely poly(butylene succinate) (PBS) and a copolymer, poly(butylene succinate-co-adipate) (PBSA). The main aim of this work is to increase the low intrinsic toughness of PLA without compromising the thermal properties by manufacturing ternary blends using epoxidized vegetable oils as compatibilizer agents. The ternary blends were manufactured by reactive extrusion in a co-rotating extruder and were subjected to mechanical, thermal, thermos-mechanical and morphology characterization. The obtained results confirm that these two succinic acid-derived polymers, i.e., PBS and PBSA, positively contribute to increase ductile properties in ternary blends with PLA and PHB with a subsequent improvement on impact toughness. In addition, both epoxidized vegetable oils, ELO and ESBO, are responsible for somewhat compatibilization between all three polyesters in blends which gives improved ductile properties with regard to uncompatibilized ternary blends. In addition, the temperature range in which these materials can be used is broader than ternary blends with other flexible polyester such as poly(e-caprolactone), as both PBS and PBSA melt at about 100 °C. These PLA-based materials with improved impact properties offer interesting applications in the packaging industry., This work was supported by the Ministry of Economy and Competitiveness (MINECO) Grant Numbers MAT2014-59242-C2-1-R and MAT2017-84909-C2-2-R. L. Quiles-Carrillo acknowledges Generalitat Valenciana (GV) for financial support through a FPI Grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU Grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Modification of poly (lactic acid) through the incorporation of gum rosin and gum rosin derivative: Mechanical performance and hydrophobicity

  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Aldás-Carrasco, Miguel Fernando
[EN] The modification of PLA by melt compound with gum rosin (GR) and pentaerythritol ester of GR (PEGR) was investigated by studying the mechanical and thermal performance, blends morphology, wettability, and water absorption. Standard testing specimens for characterization were made at a variate resin content of 5, 10, and 15 part per hundred resin (phr) and manufactured by injection molding. It was found that GR and PEGR had a lubricating effect in PLA polymeric chains, resulting in a remarkable increase of 790 and 193% in melt flow index with only 5 phr GR and PEGR contents, respectively. A significant change in more than 10 degrees of increasing water contact angle was observed for PLA with 15 phr PEGR. Thermogravimetric analysis reveals that PEGR led to delayed PLA degradation/decomposition process to higher temperature, increasing the onset temperature (T-5%) in more than 7 degrees C for PLA with 15 phr PEGR., This research was supported by the Ministry of Economy and Competitiveness-PROMADEPCOL Ref: (MAT2017-84909-C2-2-R). Authors also want to acknowledge the postdoc contract offered to José Miguel Ferri by the Generalitat Valenciana, which project title is "BIONANOCOMPOSITES BASADOS EN MEZCLAS DE PLA Y TPS CON MEMORIA" (APOSTD/2019/122) GENERALITAT VALENCIANA (2019-2021).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Effect of Varying Almond Shell Flour (ASF) Loading in Composites with Poly(Butylene Succinate (PBS) Matrix Compatibilized with Maleinized Linseed Oil (MLO)

  • Liminana, Patricia
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Balart, Rafael|||0000-0001-5670-7126
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] In this work poly(butylene succinate) (PBS) composites with varying loads of almond shell flour (ASF) in the 10-50 wt % were manufactured by extrusion and subsequent injection molding thus showing the feasibility of these combined manufacturing processes for composites up to 50 wt % ASF. A vegetable oil-derived compatibilizer, maleinized linseed oil (MLO), was used in PBS/ASF composites with a constant ASF to MLO (wt/wt) ratio of 10.0:1.5. Mechanical properties of PBS/ASF/MLO composites were obtained by standard tensile, hardness, and impact tests. The morphology of these composites was studied by field emission scanning electron microscopy-FESEM) and the main thermal properties were obtained by differential scanning calorimetry (DSC), dynamical mechanical-thermal analysis (DMTA), thermomechanical analysis (TMA), and thermogravimetry (TGA). As the ASF loading increased, a decrease in maximum tensile strength could be detected due to the presence of ASF filler and a plasticization effect provided by MLO which also provided a compatibilization effect due to the interaction of succinic anhydride polar groups contained in MLO with hydroxyl groups in both PBS (hydroxyl terminal groups) and ASF (hydroxyl groups in cellulose). FESEM study reveals a positive contribution of MLO to embed ASF particles into the PBS matrix, thus leading to balanced mechanical properties. Varying ASF loading on PBS composites represents an environmentally-friendly solution to broaden PBS uses at the industrial level while the use of MLO contributes to overcome or minimize the lack of interaction between the hydrophobic PBS matrix and the highly hydrophilic ASF filler., This research was supported by the Ministry of Economy, Industry and Competitiveness (MINECO) program number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of pine resin derivatives on the structural, thermal, and mechanical properties of Mater-Bi type bioplastic

  • Aldas-Carrasco, Miguel Fernando
  • Arrieta, Marina Patricia
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] The effect of three additives derived from pine resin, namely, gum rosin (GR) and two pentaerythritol ester of GR, Lurefor (LF) and Unik Tack (UT), in 5, 10, and 15 wt %, on the properties of Mater-Bi, based on plasticized starch, poly(butylene adipate-co-terephthalate), and poly(epsilon-caprolactone) (PCL), obtained by injection molding processes, was studied. The mechanical, microstructural, and thermal properties were evaluated. LF had a cohesive behavior with the components of Mater-Bi, increasing the toughness of the material up to 250% accompanied by an increase of tensile modulus and tensile strength. UT had an intermediate behavior, conferring cohesive and plasticizing effects, allowing an increase of 105% in impact resistance. GR had a more marked plasticizing effect. This allows processing temperatures of about 50 degrees C lower than those used for neat Mater-Bi. In addition, an increase of the elongation at break, toughness, and impact resistance in 370, 480, and 250%, respectively, was achieved., This work was supported by the Spanish Ministry of Economy and Competitiveness, PROMADEPCOL (MAT2017-84909-C2-2-R). M. P. Arrieta thanks Complutense University of Madrid for "Ayudas para la contratacion de personal postdoctoral en formacion en docencia e investigacion en departamentos de la UCM."
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microencapsulation of Copper(II) Sulfate in Ionically Cross-Linked Chitosan by Spray Drying for the Development of Irreversible Moisture Indicators in Paper Packaging

  • Rojas-Lema, Sandra
  • Terol, Jorge
  • Fages, Eduardo
  • Prieto, Cristina
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Copper(II) sulfate-loaded chitosan microparticles were herein prepared using ionic cross-linking with sodium tripolyphosphate (STPP) followed by spray drying. The microencapsulation process was optimal using an inlet temperature of 180 ºC, a liquid flow-rate of 290 mL/h, an aspiration rate of 90%, and an atomizing gas flow-rate of 667 nL/h. Chitosan particles containing copper(II) sulfate of approximately 4 microns with a shrunken-type morphology were effciently attained and, thereafter, fixated on a paper substrate either via cross-linking with STPP or using a chitosan hydrogel. The latter method led to the most promising system since it was performed at milder conditions and the original paper quality was preserved. The developed cellulose substrates were reduced and then exposed to different humidity conditions and characterized using colorimetric measurements in order to ascertain their potential as irreversible indicators for moisture detection. The results showed that the papers coated with the copper(II) sulfate-containing chitosan microparticles were successfully able to detect ambient moisture shown by the color changes of the coatings from dark brown to blue, which can be easily seen with the naked eye. Furthermore, the chitosan microparticles yielded no cytotoxicity in an in vitro cell culture experiment. Therefore, the cellulose substrates herein developed hold great promise in paper packaging as on-package colorimetric indicators for monitoring moisture in real time., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. S.R.-L. is a recipient of a Santiago Grisolia grant from Generalitat Valenciana (GVA) (GRISOLIAP/2019/132). S.T.-G. acknowledges MICI for his Juan de la Cierva Incorporación contract (IJCI-2016-29675). L.Q.-C. thanks GVA for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and Characterization of Environmentally Friendly Wood Plastic Composites from Biobased Polyethylene and Short Natural Fibers Processed by Injection Moulding

  • Dolza, Celia
  • Fages, Eduardo
  • Gonga, Eloi
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] Environmentally friendly wood plastic composites (WPC) with biobased high density polyethylene (BioHDPE) as the polymer matrix and hemp, flax and jute short fibers as natural reinforcements, were melt-compounded using twin-screw extrusion and shaped into pieces by injection molding. Polyethylene-graft-maleic anhydride (PE-g-MA) was added at two parts per hundred resin to the WPC during the extrusion process in order to reduce the lack in compatibility between the lignocellulosic fibers and the non-polar polymer matrix. The results revealed a remarkable improvement of the mechanical properties with the combination of natural fibers, along with PE-g-MA, highly improved stiffness and mechanical properties of neat BioHDPE. Particularly, hemp fiber drastically increased the Young¿s modulus and impact strength of BioHDPE. Thermal analysis revealed a slight improvement in thermal stability with the addition of the three lignocellulosic fibers, increasing both melting and degradation temperatures. The incorporation of the fibers also increased water absorption due to their lignocellulosic nature, which drastically improved the polarity of the composite. Finally, fire behavior properties were also improved in terms of flame duration, thanks to the ability of the fibers to form char protective barriers that isolate the material from oxygen and volatiles., : This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. AITEX wants to thank the European Regional Development Fund (ERDF) from the European Union for co-funding the project NABITEX Innovative technical textiles based on SUDOE natural fibers to be applied in Habitat Sector through the Interreg SUDOE Program (SOE2/P1/P0524). L.Q.-C. wants to thank Universitat Politècnica de València for his post-doctoral PAID-10-20 grant from (SP20200073). J.G.-C. wants to thank Universitat Politècnica de València for his FPI grant from (SP20200080).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A new bio-based fibre-reinforced polymer obtained from sheep wool short fibres and PLA

  • Fernando Aldas Carrasco, Miguel
  • Rouault, Nicolas Jerome
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] Within the cheese industry is used the milk of a specific species of sheep whose wool is not suitable for the fibre industry. Therefore, this fibre becomes a waste by-product. To take advantage of this waste, the formulation of a fibre-reinforced polymer based on a poly(lactic acid) (PLA) matrix plasticised with maleinised linseed oil (MLO) is proposed. The work began by evaluating the feasibility of four fibre-cleaning processes. Then, to study the composition and processing conditions of the material, a complete factorial design of experiment 22, improved with four centre-points, was considered. Afterwards, the mechanical and thermal properties of the formulations were assessed. The results showed that the most suitable washing method was the one similar to the industrial cleaning process. The reprocessing of the material increased its homogeneity due to an improvement in the fibre-matrix interface. The Pareto chart showed that there was no interaction between the wool content and the number of times the material was reprocessed. In general, the addition of sheep wool to a PLA/MLO matrix did not significantly modify the mechanical and thermal properties of the matrix. These results indicate a viable alternative to reduce the wool waste generated in the food industry by means of new bio-based material formulations., This work was supported by the Spanish Ministry of Economy and Competitiveness, Promadepcol (MAT2017-84909-C2-2-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of PBAT Processability and Mechanical Performance by Blending with Pine Resin Derivatives for Injection Moulding Rigid Packaging with Enhanced Hydrophobicity

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Aldas, Miguel
  • Arrieta, Marina P.
[EN] Polybutylene adipate-co-terephthalate (PBAT) is a biodegradable polymer with good features for packaging applications. However, the mechanical performance and high prices of PBAT limit its current usage at the commercial level. To improve the properties and reduce the cost of PBAT, pine resin derivatives, gum rosin (GR) and pentaerythritol ester of GR (UT), were proposed as sustainable additives. For this purpose, PBAT was blended with 5, 10, and 15 wt.% of additives by melt-extrusion followed by injection moulding. The overall performance of the formulations was assessed by tensile test, microstructural, thermal, and dynamic mechanical thermal analysis. The results showed that although good miscibility of both resins with PBAT matrix was achieved, GR in 10 wt.% showed better interfacial adhesion with the PBAT matrix than UT. The thermal characterization suggested that GR and UT reduce PBAT melting enthalpy and enhance its thermal stability, improving PBAT processability. A 10 wt.% of GR significantly increased the tensile properties of PBAT, while a 15 wt.% of UT maintained PBAT tensile performance. The obtained materials showed higher hydrophobicity than neat PBAT. Thus, GR and UT demonstrated that they are advantageous additives for PBAT-resin compounding for rigid food packaging which are easy to process and adequate for industrial scalability. At the same time, they enhance its mechanical and hydrophobic performance., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), projects: PROMADEPCOL (MAT2017-84909-C2-2-R) and CTM2017-88989-P as well as by the European Union s Horizon 2020 research and innovation program under grant agreement no. 860407 BIO-PLASTICS EUROPE. M.A. thanks Secretaría de Educación Superior, Ciencia, Tecnología e Innovación (SENESCYT) and Escuela Politécnica Nacional (EPN). C.P. thanks Santiago Grisolía fellowship (GRISOLIAP/2019/113) from Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Upgrading Argan Shell Wastes in Wood Plastic Composites with Biobased Polyethylene Matrix and Different Compatibilizers

  • Jordá-Reolid, María
  • Stefani, Pablo Marcelo
  • Rojas-Lema, Sandra Paola
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] The present study reports on the development of wood plastic composites (WPC) based on micronized argan shell (MAS) as a filler and high-density polyethylene obtained from sugarcane (Bio-HDPE), following the principles proposed by the circular economy in which the aim is to achieve zero waste by the introduction of residues of argan as a filler. The blends were prepared by extrusion and injection molding processes. In order to improve compatibility between the argan particles and the green polyolefin, different compatibilizers and additional filler were used, namely polyethylene grafted maleic anhydride (PE-g-MA 3 wt.-%), maleinized linseed oil (MLO 7.5 phr), halloysite nanotubes (HNTs 7.5 phr), and a combination of MLO and HNTs (3.75 phr each). The mechanical, morphological, thermal, thermomechanical, colorimetric, and wettability properties of each blend were analyzed. The results show that MAS acts as a reinforcing filler, increasing the stiffness of the Bio-HDPE, and that HNTs further increases this reinforcing effect. MLO and PE-g-MA, altogether with HNTs, improve the compatibility between MAS and Bio-HDPE, particularly due to bonds formed between oxygen-based groups present in each compound. Thermal stability was also improved provided by the addition of MAS and HNTs. All in all, reddish-like brown wood plastic composites with improved stiffness, good thermal stability, enhanced compatibility, and good wettability properties were obtained., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Properties of biobased epoxy resins from epoxidized linseed oil (ELO) crosslinked with a mixture of cyclic anhydride and maleinized linseed oil

  • Samper, María-Dolores|||0000-0002-5102-8412
  • Ferri, J.M|||0000-0002-1269-4973
  • Balart, Rafael|||0000-0001-5670-7126
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Carbonell-Verdu, Alfredo
[EN] This works aims at the development thermosetting resins derived from epoxidized linseed oil (ELO) of high biobased content, by using a mixture of crosslinking agents, i.e. methyl nadic anhydride (MNA) and maleinized linseed oil (MLO). By using only MNA as crosslinking agent, the obtained resins are characterized by high stiffness and, consequently, high fragility. When MLO content increasing in the crosslinking mixture, up to 25 wt%, a decrease in mechanical resistant and thermomechanical is detected, thus indicating that MLO can provide flexibility to ELO-based thermosetting resins which is an interesting issue to obtain tailored properties by selecting the appropriate mixture composition. In general, the thermosetting resin crosslinked with 10 wt% MLO and 40 wt% MNA gives balanced properties together with noticeable biobased content, thus broadening the potential of these materials for uses in green composites and coatings, This work has been supported by the Spanish Ministry of Economy and Competitiveness, PROMADEPCOL (MAT2017-84909-C2-2-R). MDS is recipient of a APOSTD2018 contract (APOSTD/2018/209) from Conselleria d'Educacio, Investigacio, Cultura y Esport de la Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bilayer films of poly(epsilon-caprolactone) electrosprayed with gum rosin microspheres: Processing and characterization

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Samper, María-Dolores|||0000-0002-5102-8412
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Aldas, Miguel
  • ARRIETA, Marina Patricia
[EN] Bilayer systems, consisting of electrosprayed gum rosin microspheres (eGR) and poly(epsilon-caprolactone) (PCL), were prepared. First, the electrospraying processing conditions of GR in two different solvents, dichloromethane, and chloroform, were optimized. Various electrospraying polymeric solution flow rates and applied voltages were tested and morphologically analyzed in terms of particle size distribution and microspheres density. The conditions at which a homogeneous and narrow microspheres size distribution was achieved were chosen as the best for each solvent. The eGR was deposited onto a compression-molded PCL film to obtain the bilayer systems. The bilayer systems were characterized by their visual appearance, microstructural analyses, thermal and mechanical performance, and surface wettability. It was determined that the mechanical and thermal behavior of PCL film was not affected due to the addition of the eGR microspheres layer. Meanwhile, the eGR layer considerably changes the surface color of the PCL film, reduces the film transparency, and produces a blocking effect in the UVB region and high blockage in the UVA region. In addition, the microspheres layer presents a tunable hydrophobicity depending on the solvent used, reaching values of ultrahydrophobic surfaces. Thus, the obtained result reveals a great potential to easily process bilayer systems with high interest in sustainable agricultural, packaging, and/or biomedical applications., Spanish Ministry of Economy and Competitiveness (MINECO), Grant/Award Number: PROMADEPCOL (MAT2017-84909-C2-2-R)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Faba bean protein films reinforced with cellulose nanocrystals as edible food packaging material

  • Rojas-Lema, Sandra
  • Nilsson, Klara
  • Trifol, Jon
  • Langton, Maud
  • Moriana, Rosana
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
[EN] In the present work, transparent films were obtained by the solution casting method from faba bean protein isolate (FBP), reinforced with different cellulose nanocrystals (CNCs) content (1, 3, 5 and 7 wt%), obtained by acid hydrolysis of pine cone, and using glycerol as plasticizer. The influence of different CNCs loadings on the mechanical, thermal, barrier, optical, and morphological properties was discussed. Microstructurally, the FTIR and FESEM results corroborated the formation of intramolecular interactions between the CNCs and proteins that lead to more compact and homogeneous films. These interactions had a positive influence on the mechanical strength properties, which is reflected in higher tensile strength and Young's modulus in reinforced films with respect to the control film, resulting in stiffer films as the CNCs content increases. Thermal stability of the FBP films was also improved with the presence of CNCs, by increasing the characteristic onset degradation temperature. In addition, the linkages formed between the CNCs, and proteins reduced the water affinity of the reinforced films, leading to a reduction in their moisture content and water solubility, and an increase in their water contact angle, obtaining more hydrophobic films as the CNCs content in the matrix increased. The addition of CNCs in the FBP film also considerably improved its barrier properties, reducing its water vapour transmission rate (WVTR) and oxygen transmission rate (OTR). The present work shows the possibility of obtaining biobased and biodegradable films of CNC-reinforced FBP with improved mechanical, thermal and barrier properties, and low water susceptibility, which can be of great interest in the food packaging sector as edible food packaging material., This research was supported by the Ministry of Science and Inno-vation (MICI) [MAT2017-84909-C2-2-R] . S. Rojas-Lema thanks the Generalitat Valenciana (GVA) for the financial support through a San-tiago Grisolia grant (GRISOLIAP/2019/132) . D. Garcia-Garcia wants to thank the Ministry of Science, Innovation and Universities for their financial support through the "Jose Castillejo" mobility grant (CAS19/00332).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A Deeper Microscopic Study of the Interaction between Gum Rosin Derivatives and a Mater-Bi Type Bioplastic

  • Aldas-Carrasco, Miguel Fernando
  • Arrieta, Marina P.
  • E. Rayón|||0000-0002-0653-2046
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] The interaction between gum rosin and gum rosin derivatives with Mater-Bi type bioplastic, a biodegradable and compostable commercial bioplastic, were studied. Gum rosin and two pentaerythritol esters of gum rosin (Lurefor 125 resin and Unik Tack P100 resin) were assessed as sustainable compatibilizers for the components of Mater-Bi® NF 866 polymeric matrix. To study the influence of each additive in the polymeric matrix, each gum rosin-based additive was compounded in 15 wt % by melt-extrusion and further injection molding process. Then, the mechanical properties were assessed, and the tensile properties and impact resistance were determined. Microscopic analyses were carried out by field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and atomic force microscopy with nanomechanical assessment (AFM-QNM). The oxygen barrier and wettability properties were also assayed. The study revealed that the commercial thermoplastic starch is mainly composed of three phases: A polybutylene adipate-co-terephthalate (PBAT) phase, an amorphous phase of thermoplastic starch (TPSa), and a semi-crystalline phase of thermoplastic starch (TPSc). The poor miscibility among the components of the Mater-Bi type bioplastic was confirmed. Finally, the formulations with the gum rosin and its derivatives showed an improvement of the miscibility and the solubility of the components depending on the additive used, This research was funded by Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R) and M.P.A. s contract: Juan de la Cierva-Incorporación (FJCI-2017-33536).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of Compatibilized Polyamide 1010/Coconut Fibers Composites by Reactive Extrusion with Modified Linseed Oil and Multi-functional Petroleum Derived Compatibilizers

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Puglia, D.
  • Dominici, F.
  • Torre, L.
[EN] This work reports the preparation and characterization of fully bio-based polymer composites with coconut fibers (CFs) as an alternative to wood-plastic composites (WPCs), typically based on petroleum derived materials. Polyamide 1010 (PA1010) was melt-extruded with 20 wt% of CFs and, after that, shaped into pieces by injection molding. Four different multi-functionalized compatibilizers were tested to increase the polymer-fiber interactions with the subsequent improvement on toughness. These consisted of two chemically modified vegetable oils, namely maleinized and epoxidized linseed oil (MLO and ELO) respectively, and two commercial additives derived from petroleum and based on glycidyl functionality, that is, low-functionality epoxy-based styrene-acrylic oligomer (ESAO) and polystyrene-glycidyl methacrylate random copolymer (PS-GMA). The addition of all four compatibilizers improved both the mechanical and thermomechanical properties of the composites, thus resulting in high-performance composite materials with relatively low water uptake. Furthermore, the morphology of the obtained composites revealed an extraordinary embedment of the fibers into the biopolymer matrix, which plays a crucial role in improving toughness. Among all the tested compatibilizers, those derived from vegetable oils can be considered the most interesting ones due to they offer a more sustainable solution., This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. Quiles-Carrillo and Torres-Giner are recipients of a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) and a Juan de la Cierva contract (IJCI-2016-29675) from MICIU, respectively. The microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images. The authors thank Polyscope for kindly supplying Xibond (TM) 920 for this study.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancement of the processing window and performance of polyamide 1010/bio-based high-density polyethylene blends by melt mixing with natural additives

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] This work reports the enhancement of the processing window and the mechanical and thermal properties of biopolymer blends of polyamide 1010 (PA1010) and bio-based high-density polyethylene (bio-HDPE) at 70/30 (wt/wt) achieved by means of natural additives. The overall performance of the binary blend melt-mixed without additives was poor due to both the relatively low thermal stability of bio-HDPE at the processing temperatures of PA1010, that is, 210¿240 ºC, and the lack or poor miscibility between the two biopolymers. Gallic acid (GA), a natural phenolic compound, was added at 0.8 parts per hundred resin (phr) of biopolymer blend to enhance the thermal stability of the green polyolefin and therefore enlarge the processing window of the binary blend. Maleinized linseed oil (MLO), a multi-functionalized vegetable oil, was then incorporated at 5 phr to compatibilize the biopolymers and its performance was also compared with that of a conventional petroleum-derived copolymer, namely, poly(ethylene-co-acrylic acid) (PE-co-AA). The resultant biopolymer blends showed a remarkable enhancement in the thermal stability and also improved toughness when both natural additives were combined. This work can potentially serve as a sound base study for the mechanical recycling of similar blends based on bio-based but non-biodegradable polymers., This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. LQ-C and ST-G are recipients of an FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) and a Juan de la Cierva-Incorporacion contract (IJCI-2016-29675) from MICIU, respectively. The microscopy services at Universitat Politecnica de Valencia (UPV) are acknowledged for their help in collecting and analysing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evaluation of Different Compatibilization Strategies to Improve the Performance of Injection-Molded Green Composite Pieces Made of Polylactide Reinforced with Short Flaxseed Fibers

  • Agüero, Ángel
  • Rojas-Lema, Sandra Paola
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Green composites made of polylactide (PLA) and short flaxseed fibers (FFs) at 20 wt % were successfully compounded by twin-screw extrusion (TSE) and subsequently shaped into pieces by injection molding. The linen waste derived FFs were subjected to an alkalization pretreatment to remove impurities, improve the fiber surface quality, and make the fibers more hydrophobic. The alkali-pretreated FFs successfully reinforced PLA, leading to green composite pieces with higher mechanical strength. However, the pieces also showed lower ductility and toughness and the lignocellulosic fibers easily detached during fracture due to the absence or low interfacial adhesion with the biopolyester matrix. Therefore, four different compatibilization strategies were carried out to enhance the fiber-matrix interfacial adhesion. These routes consisted on the silanization of the alkalized FFs with a glycidyl silane, namely (3-glycidyloxypropyl) trimethoxysilane (GPTMS), and the reactive extrusion (REX) with three compatibilizers, namely a multi-functional epoxy-based styrene-acrylic oligomer (ESAO), a random copolymer of poly(styrene-co-glycidyl methacrylate) (PS-co-GMA), and maleinized linseed oil (MLO). The results showed that all the here-tested compatibilizers improved mechanical strength, ductility, and toughness as well as the thermal stability and thermomechanical properties of the green composite pieces. The highest interfacial adhesion was observed in the green composite pieces containing the silanized fibers. Interestingly, PS-co-GMA and, more intensely, ESAO yielded the pieces with the highest mechanical performance due to the higher reactivity of these additives with both composite components and their chain-extension action, whereas MLO led to the most ductile pieces due to its secondary role as plasticizer for PLA., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. D.L. and J.I.-M. thanks UPV for the grant received through the PAID-01-18 and PAID-01-19 (SP2019001) programs, respectively. S.T.-G. is recipient of a Juan de la Cierva contract (IJCI-2016-29675) from MICIU while S.R.J. is funded through the Santiago Gisolía contract (GRISOLIAP/2019/132) from Generalitat Valenciana (GVA). The microscopy services of UPV are also acknowledged for their help in collecting and analyzing the FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and Characterization of Weft-Knitted Fabrics of Naturally Occurring Polymer Fibers for Sustainable and Functional Textiles

  • Ferrándiz, Marcela
  • Fages, Eduardo
  • Rojas-Lema, Sandra Paola
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] This study focuses on the potential uses in textiles of fibers of soy protein (SP) and chitin, which are naturally occurring polymers that can be obtained from agricultural and food processing by-products and wastes. The as-received natural fibers were first subjected to a three-step manufacturing process to develop yarns that were, thereafter, converted into fabrics by weft knitting. Different characterizations in terms of physical properties and comfort parameters were carried out on the natural fibers and compared to waste derived fibers of coir and also conventional cotton and cotton-based fibers, which are widely used in the textile industry. The evaluation of the geometry and mechanical properties revealed that both SP and chitin fibers showed similar fineness and tenacity values than cotton, whereas coir did not achieve the expected properties to develop fabrics. In relation to the moisture content, it was found that the SP fibers outperformed the other natural fibers, which could successfully avoid variations in the mechanical performance of their fabrics as well as impair the growth of microorganisms. In addition, the antimicrobial activity of the natural fibers was assessed against different bacteria and fungi that are typically found on the skin. The obtained results indicated that the fibers of chitin and also SP, being the latter functionalized with biocides during the fiber-formation process, showed a high antimicrobial activity. In particular, reductions of up to 100% and 60% were attained for the bacteria and fungi strains, respectively. Finally, textile comfort was evaluated on the weft-knitted fabrics of the chitin and SP fibers by means of thermal and tactile tests. The comfort analysis indicated that the thermal resistance of both fabrics was similar to that of cotton, whereas their air permeability was higher, particularly for chitin due to its higher fineness, which makes these natural fibers very promising for summer clothes. Both the SP and chitin fabrics also presented relatively similar values of fullness and softness than the pure cotton fabric in terms of body feeling and richness. However, the cotton/polyester fabric was the only one that achieved a good range for uses in winter-autumn cloths. Therefore, the results of this work demonstrate that non-conventional chitin and SP fibers can be considered as potential candidates to replace cotton fibers in fabrics for the textile industry due to their high comfort and improved sustainability. Furthermore, these natural fibers can also serve to develop novel functional textiles with antimicrobial properties., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Maleinized Linseed Oil as Epoxy Resin Hardener for Composites with High Bio Content Obtained from Linen Byproducts

  • Fombuena, Vicent|||0000-0001-7266-6205
  • Jorda-Vilaplana, Amparo
  • Montanes, Nestor|||0000-0001-6070-127X
  • Petrucci, Roberto
  • Dominici, Franco
  • Torre, Luigi
[EN] Green composites, with more than 78 wt.% of products obtained from linen Linum usitatissimum, were developed in this research work. Epoxidized linseed oil (ELO) was used as bio-based resin, a mix of nadic methyl anhydride (MNA) and maleinized linseed oil (MLO) were used as cross-linkers and finally, flax fabrics were used to obtain composite laminates by resin transfer molding (RTM). The flax fibers were modified using amino-silane, glycidyl-silane and maleic anhydride treatment in order to increase the compatibility between lignocellulosic fibers and the polymeric matrix. Mechanical and thermal properties were studied by flexural, tensile and impact test, as well as dynamic mechanical analyses (DMA) to study the viscoelastic behavior. Contrary to what could be expected, when fibers are previously treated in presence of MLO, a reduction of anchorage points is obtained causing a substantial increase in the ductile properties compared with composites without previous fiber treatment or without MLO., This work was supported by the Ministry of Economy and Competitiveness (MINECO) (grant number MAT2017-84909-C2-2-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Compatibilization and Characterization of Polylactide and Biopolyethylene Binary Blends by Non-Reactive and Reactive Compatibilization Approaches

  • Ferri, J.M|||0000-0002-1269-4973
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • E. Rayón|||0000-0002-0653-2046
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Balart, Rafael|||0000-0001-5670-7126
[EN] In this study, different compatibilizing agents were used to analyze their influence on immiscible blends of polylactide (PLA) and biobased high-density polyethylene (bioPE) 80/20 (wt/wt). The compatibilizing agents used were polyethylene vinyl acetate (EVA) with a content of 33% of vinyl acetate, polyvinyl alcohol (PVA), and dicumyl peroxide (DPC). The influence of each compatibilizing agent on the mechanical, thermal, and microstructural properties of the PLA-bioPE blend was studied using different microscopic techniques (i.e., field emission electron microscopy (FESEM), transmission electron microscopy (TEM), and atomic force microscopy with PeakForce quantitative nanomechanical mapping (AFM-QNM)). Compatibilized PLA-bioPE blends showed an improvement in the ductile properties, with EVA being the compatibilizer that provided the highest elongation at break and the highest impact-absorbed energy (Charpy test). In addition, it was observed by means of the different microscopic techniques that the typical droplet-like structure is maintained, but the use of compatibilizers decreases the dimensions of the dispersed droplets, leading to improved interfacial adhesion, being more pronounced in the case of the EVA compatibilizer. Furthermore, the incorporation of the compatibilizers caused a very marked decrease in the crystallinity of the immiscible PLA-bioPE blend, This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU), project numbers MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and characterization of environmentally friendly composites from poly(butylene succinate) (PBS) and almond shell flour with different compatibilizers

  • Liminana, P.
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This work reports the enhancement of the properties of poly (butylene succinate) (PBS) composites containing 30 wt% almond shell flour (ASF) by using different compatibilizer families: epoxy, maleic anhydride and acrylic. With regard to the epoxy compatibilizers, epoxidized linseed oil (ELO) and epoxidized soybean oil (ESBO) were used. Two maleic anhydride-derived compatibilizers, namely, maleinized linseed oil (MLO) and dodecenyl succinic anhydride (DDSA) were used. Finally, two acrylic monomers, namely methyl methacrylate (MMA) and acrylic acid (AA) were employed. Uncompatibilized and compatibilized PBS/ASF composites were characterized in terms of their mechanical properties, morphology, thermal behaviour and thermomechanical performance. The obtained results suggest that all three vegetable oil-derived compatibilizers (ELO, ESBO and MLO) give a remarkable increase in ductile properties while poor compatibilization is obtained with the acrylic monomers. These vegetable-oil derived compatibilizers could represents an interesting environmentally friendly solution to compatibilizing polyester-type polymers and their composites with lignocellulosic materials., This work was supported by the Ministry of Economy and Competitiveness (MINECO) grant numbers MAT2014-59242-C2-1-R and MAT2017-84909-C2-2-R. L. Quiles-Carrillo acknowledges Generalitat Valenciana (GV) for financial support through a FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding

  • Agüero, Ángel
  • Morcillo, Maria del Carmen
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Fenollar, Octavio|||0000-0003-4323-7414
[EN] This research work aims to study the influence of the reprocessing cycles on the mechanical, thermal, and thermomechanical properties of polylactide (PLA). To this end, PLA was subjected to as many as six extrusion cycles and the resultant pellets were shaped into pieces by injection molding. Mechanical characterization revealed that the PLA pieces presented relatively similar properties up to the third reprocessing cycle, whereas further cycles induced an intense reduction in ductility and toughness. The effect of the reprocessing cycles was also studied by the changes in the melt fluidity, which showed a significant increase after four reprocessing cycles. An increase in the bio-polyester chain mobility was also attained with the number of the reprocessing cycles that subsequently favored an increase in crystallinity of PLA. A visual inspection indicated that PLA developed certain yellowing and the pieces also became less transparent with the increasing number of reprocessing cycles. Therefore, the obtained results showed that PLA suffers a slight degradation after one or two reprocessing cycles whereas performance impairment becomes more evident above the fourth reprocessing cycle. This finding suggests that the mechanical recycling of PLA for up to three cycles of extrusion and subsequent injection molding is technically feasible., This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). D. Lascano wants to thank UPV for the grant received through the PAID-01-18 program. S. Torres-Giner is recipient of a Juan de la Cierva¿ Incorporación contract (IJCI-2016-29675) from MICIU. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Green antioxidant composites based on coffee by-products from the alcohol industry

  • Terroba-Delicado, Enrique
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] Bio-based high-density polyethylene (BioHDPE)-loaded composites with different amounts of spent coffee powder (up to 30 wt.%) were successfully produced. The use of coffee residues coming from the alcoholic beverage industry in a BioHDPE matrix resulted in a remarkable improvement in the antioxidant properties of the composites. Waste spent coffee powder reduced the elastic modulus, hardness and storage modulus; the reduction was proportional to the amount of by-product considered. To improve the interaction between the highly hydrophobic BioHDPE matrix and the highly hydrophilic spent coffee powder, a copolymer - namely, poly(ethylene-graft-maleic anhydride) (PE-g-MA) - was used. PE-g-MA addition resulted in an improved interaction between the particles and poly(lactic acid), as confirmed by field emission scanning electron microscopy. On the other hand, the presence of the lignocellulosic filler resulted in a low load transfer between the two components, which led to a decrease in tensile strength. The introduction of coffee powder resulted in an improvement in thermal stability, as confirmed by thermogravimetry and differential scanning calorimetry. Finally, antioxidant activity was also observed in the composites, wherein a 27% reduction in 2,2-diphenyl-1-picrylhydrazyl was reported for the composite with the highest coffee content. The presence of antioxidant substances (coffee oil) was confirmed by Fourier transform infrared spectroscopy., This research is a part of the grant PID2020-116496RB-C22, funded by MCIN/AEI/10.13039/501100011033, and the grant TED2021-131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union "NextGenerationEU"/PRTR. The authors also thank Generalitat Valenciana-GVA for funding this research through the grant numbers AICO/2021/025 and CIGE/2021/094. Funded with Aid for First Research Projects (PAID-06-22), Vice-rectorate for Research of the Universitat Politecnica de Valencia (UPV). J. Ivorra-Martinez would like to express thanks for FPU19/01759 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. J. Gomez-Caturla would like to express thanks for FPU20/01732 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. Also, Microscopy Services at UPV are also acknowledged for their help in collecting and analyzing images. The authors also want to acknowledge Licores Sinc (Alcoy, Spain) for its collaboration in this project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacturing and Characterization of Hybrid Composites with Basalt and Flax Fabrics and a Partially Bio-based Epoxy Resin

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Balart, Rafael|||0000-0001-5670-7126
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
  • Agüero-Rodríguez, Ángel
[EN] This research is focused on manufacturing and characterization of hybrid composite laminates obtained different stacking sequences of basalt and flax fabrics with silane treatments embedded in a partially bio-sourced epoxy resin as matrix. They were manufactured by the vacuum-assisted resin infusion molding and mechanical properties were tested in tensile, flexural and impact conditions. The effect of the coupling agent on the fiber/matrix interface was studied by FESEM. The effect of temperature on mechanical properties was evaluated by DMTA and TMA. FESEM images revealed improved fiber/matrix interactions with silane treatment, having a more satisfactory effect on basalt fibers than on flax fibers because of its silica-based structure, leading to improved mechanical properties. It is worthy to note that the hybrid stacking sequence has no remarkable influence on the elongation at break. On the contrary, the hybrid stacking sequence offered a great influence on both the elastic modulus and the tensile strength., This research was funded by the Ministerio de Economía, Industria y Competitividad (MICINN) project number MAT2017-84909-C2-2-R. D. Lascano wants to thank UPV for the grant received though the PAID-01-18 program. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of the Curing and Post-Curing Conditions for the Manufacturing of Partially Bio-Based Epoxy Resins with Improved Toughness

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This research deals with the influence of different curing and post-curing temperatures on the mechanical and thermomechanical properties as well as the gel time of an epoxy resin prepared by the reaction of diglycidyl ether of bisphenol A (DGEBA) with an amine hardener and a reactive diluent derived from plants at 31 wt %. The highest performance was obtained for the resins cured at moderate-to-high temperatures, that is, 80 degrees C and 90 degrees C, which additionally showed a significant reduction in the gel time. This effect was ascribed to the formation of a stronger polymer network by an extended cross-linking process of the polymer chains during the resin manufacturing. Furthermore, post-curing at either 125 degrees C or 150 degrees C yielded thermosets with higher mechanical strength and, more interestingly, improved toughness, particularly for the samples previously cured at moderate temperatures. In particular, the partially bio-based epoxy resin cured at 80 degrees C and post-cured at 150 degrees C for 1 h and 30 min, respectively, showed the most balanced performance due to the formation of a more homogeneous cross-linked structure., This research was supported by the Spanish Ministry of Science, Innovation, and Universities (MICIU) through the MAT2017-84909-C2-2-R program number. D.L. acknowledges Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. L.Q.-C. wants to thank the Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. is a recipient of a Juan de la Cierva¿Incorporación contract (IJCI-2016-29675) from MICIU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bio-Polyethylene-Based Composites Reinforced with Alkali and Palmitoyl Chloride-Treated Coffee Silverskin

  • Dominici, Franco
  • Luzi, Francesca
  • Puglia, Debora
  • Torre, Luigi
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Balart, Rafael|||0000-0001-5670-7126
[EN] This work investigates the feasibility of using coffee silverskin (CSS) as a reinforcing agent in biobased polyethylene (BioPE) composites, by adding it in bulk and thin film samples. The effect of two different treatments, alkali bleaching (CSS_A) and esterification with palmitoyl chloride (CSS_P), on mechanical, thermal, morphological and water absorption behavior of produced materials at different CSS loading (10, 20 and 30 wt %) was investigated. A reactive graft copolymerization of BioPE with maleic anhydride was considered in the case of alkali treated CSS. It was found that, when introduced in bulk samples, improvement in the elastic modulus and a reduction in strain at maximum stress were observed with the increase in CSS fraction for the untreated and treated CSS composites, while the low aspect ratio of the CSS particles and their poor adhesion with the polymeric matrix were responsible for reduced ductility in films, decreasing crystallinity values and reduction of elastic moduli. When CSS_A and CSS_P are introduced in the matrix, a substantial reduction in the water uptake is also obtained in films, mainly due to presence of maleated PE, that builds up some interactions to eliminate the amounts of OH groups and hydrophobized CSS, due to the weakened absorption capacity of the functionalized CSS., This research was partially funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. D.G.G. wants to thank the Universitat Politècnica de València for financial support through a postdoctoral contract [PAID-10-18].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Impact of Biodegradable Plastics in the Properties of Recycled Polyethylene Terephthalate

  • Aldas, Miguel
  • Bertomeu, David
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Rosa-Ramírez, Harrison de la|||0000-0002-2913-7938
  • Ferri, J.M|||0000-0002-1269-4973
  • Samper, María-Dolores|||0000-0002-5102-8412
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Since biodegradable materials are unwittingly mixed with synthetic materials, this work aimed to study the feasibility of reliably identifying some biopolymers, treated as contaminants, in the recycling process of polyethylene terephthalate (PET). The results showed that the miscibility between PET-PLA and PET-PHB is good. However, PHB is degraded in the recycling of PET due to the high processing temperatures used; meanwhile, PET and TPS are poorly miscible, characteristics also reflected in the microstructure. The contaminants decrease the mechanical properties of the recycled PET. WCA, FTIR, and DSC, do not allow to identify of these contaminants. FESEM resulted in the most successful technique to detect the biodegradable polymers in the PET matrix. No significant degradation of PET under composting conditions was obtained due to the presence of biodegradable polymers, and the effects of the biodegradable contaminants continue to reduce the mechanical performance of the recycled PET after 1 year of storage., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R). M.A. thanks Secretaria de Educacion Superior, Ciencia, Tecnologia e Innovacion (SENESCYT, Ecuador) and Escuela Politecnica Nacional. C.P. thanks Santiago Grisolia fellowship (GRISOLIAP/2019/113) from Generalitat Valenciana. J.M.F. thanks to Posdoctoral GVA fellowship (APOSTD/2019/122). from Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Efect of Different Compatibilizers on Injection-Molded Green Fiber-Reinforced Polymers Based on Poly(lactic acid)-Maleinized Linseed Oil System and Sheep Wool

  • Pawlak, Franciszek
  • Aldas-Carrasco, Miguel Fernando
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] A method to modify polymers is that of introducing fibers in a matrix to produce a fiber-reinforced polymer (FRP). Consequently, the aim of this work was to study the compatibility effect of four coupling agents on wool FRP properties, using poly(lactic acid) plasticized with maleinized linseed oil as polymer matrix. The content of wool assessed was 1 phr. The compatibilizers were (3-(2-aminoethylamino)propyl)-trimethoxysilane, trimethoxy (2-(7-oxabicyclo (4.1.0)hept-3-yl) ethyl) silane, tris(2-methoxyethoxy)(vinyl) silane and titanium (IV) (triethanolaminate)isopropoxide. Initially, wool was modified with coupling agents in an acetone/water (50/50) solution. Mechanical properties were evaluated by tensile and flexural properties, hardness by Shore D measurement and impact resistance by Charpy's energy. Differential scanning calorimetry, dynamic thermo-mechanical analysis, and thermogravimetric analysis were conducted to evaluate the interaction among components and the effect of the coupling agents on the thermal properties of the original material. Color, wettability and scanning electron microscopy were used to describe physical and microstructural properties. Modification of fibers allows achieving improved mechanical properties and changes the thermal properties of the FRPs slightly. Coupling agent treatment helps to formulate PLA-MLO and sheep wool materials and to improve their performance, thereby creating a broader spectrum of applications for PLA maintaining the bio-based character of the material., This work has been supported by the Spanish Ministry of Economy and Competitiveness, PROMADEPCOL (MAT2017-84909-C2-2-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Identification of biodegradable polymers as contaminants in the thermoplastic recycling process

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Ferri, J.M|||0000-0002-1269-4973
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Aldás-Carrasco, Miguel Fernando
  • Bertomeu, David
  • Pawlak, Franciszek
[EN] In this work, the presence of biodegradable polymers in recycled plastic materials was characterized using readily available techniques. Recycled polypropylene (PP), polystyrene (PS) and polyethylene terephthalate (PET) were studied. The contamination of these plastics with polylactic acid (PLA), polyhydroxybutyrate (PHB) and thermoplastic starch (TPS) was simulated using 10 wt.% of the contaminant. Fourier transform infrared spectrometry (FTIR) and differential scanning calorimetry (DSC) were used as characterization techniques. In addition, the effect of aging on recycled products from PET blends contaminated with TPS and PHB was studied. The results show changes in the intensity of the FTIR spectra bands of the PS and PP blends contaminated with biodegradable polymers. By DSC, changes in the cold crystallization peak of recycled PET are observed when mixed with TPS and PHB. When the contaminant is PLA, the changes are masked due to the thermal characteristics of both materials. In PS, changes in the calorimetric curves are identified by the presence of PLA and PHB. Contamination with PLA, PHB and TPS hinders the processing of recycled PET after one year of storage due to the aging of the material., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), projects: PROMADEPCOL (MAT2017-84909-C2-2-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacturing and Characterization of Highly Environmentally Friendly Sandwich Composites from Polylactide Cores and Flax-Polylactide Faces

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Balart, Rafael|||0000-0001-5670-7126
  • Montanes, Nestor|||0000-0001-6070-127X
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Guillén-Pineda, René Miguel
[EN] This work focuses on the manufacturing and characterization of highly environmentally friendly lightweight sandwich structures based on polylactide (PLA) honeycomb cores and PLA-flax fabric laminate skins or facings. PLA honeycombs were manufactured using PLA sheets with different thicknesses ranging from 50 to 500 mu m. The PLA sheets were shaped into semi-hexagonal profiles by hot-compression molding. After this stage, the different semi-hexagonal sheets were bonded together to give hexagonal panels. The skins were manufactured by hot-compression molding by stacking two Biotex flax/PLA fabrics with 40 wt% PLA fibers. The combined use of temperature (200 degrees C), pressure, and time (2 min) allowed PLA fibers to melt, flow, and fully embed the flax fabrics, thus leading to thin composite laminates to be used as skins. Sandwich structures were finally obtained by bonding the PLA honeycomb core with the PLA-flax skins using an epoxy adhesive. A thin PLA nonwoven was previously attached to the external hexagonal PLA core, to promote mechanical interlock between the core and the skins. The influence of the honeycomb core thickness on the final flexural and compression properties was analyzed. The obtained results indicate that the core thickness has a great influence on the flexural properties, which increases with core thickness; nevertheless, as expected, the bonding between the PLA honeycomb core and the skins is critical. Excellent results have been obtained with 10 and 20 mm thickness honeycombs with a core shear of about 0.60 and facing bending stresses of 31-33 MPa, which can be considered as candidates for technical applications. The ultimate load to the sample weight ratio reached values of 141.5 N center dot g(-1) for composites with 20 mm thick PLA honeycombs, which is comparable to other technical composite sandwich structures. The bonding between the core and the skins is critical as poor adhesion does not allow load transfer and, while the procedure showed in this research gives interesting results, new developments are necessary to obtain standard properties on sandwich structures., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Tailoring the Properties of Thermo-Compressed Polylactide Films for Food Packaging Applications by Individual and Combined Additions of Lactic Acid Oligomer and Halloysite Nanotubes

  • Rojas-Lema, Sandra
  • Melendez-Rodriguez, Beatriz
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] In this work, films of polylactide (PLA) prepared by extrusion and thermo-compression were plasticized with oligomer of lactic acid (OLA) at contents of 5, 10, and 20 wt%. The PLA sample containing 20 wt% of OLA was also reinforced with 3, 6, and 9 parts per hundred resin (phr) of halloysite nanotubes (HNTs) to increase the mechanical strength and thermal stability of the films. Prior to melt mixing, ultrasound-assisted dispersion of the nanoclays in OLA was carried out at 100 ºC to promote the HNTs dispersion in PLA and the resultant films were characterized with the aim to ascertain their potential in food packaging. It was observed that either the individual addition of OLA or combined with 3 phr of HNTs did not significantly affect the optical properties of the PLA films, whereas higher nanoclay contents reduced lightness and induced certain green and blue tonalities. The addition of 20 wt% of OLA increased ductility of the PLA film by nearly 75% and also decreased the glass transition temperature (Tg) by over 18 ºC. The incorporation of 3 phr of HNTs into the OLA-containing PLA films delayed thermal degradation by 7 ºC and additionally reduced the permeabilities to water and limonene vapors by approximately 8% and 47%, respectively. Interestingly, the highest barrier performance was attained for the unfilled PLA film plasticized with 10 wt% of OLA, which was attributed to a crystallinity increase and an effect of ¿antiplasticization¿. However, loadings of 6 and 9 phr of HNTs resulted in the formation of small aggregates that impaired the performance of the blend films. The here-attained results demonstrates that the properties of ternary systems of PLA/OLA/HNTs can be tuned when the plasticizer and nanofiller contents are carefully chosen and the resultant nanocomposite films can be proposed as a bio-sourced alternative for compostable packaging applications., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. S.R.-L is a recipient of a Santiago Grisolia grant from Generalitat Valenciana (GVA) (GRISOLIAP/2019/132). L.Q.-C. wants to thank GVA for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812), while D.G.-G. also acknowledges GVA for his postdoctoral contract (APOSTD/2019/201). B.M.-R. and S.T.-G. acknowledge MICIU for her FPI grant (BES-2016-077972) and his Juan de la Cierva¿Incorporación contract (IJCI-2016-29675), respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Quantification of poisons for Ziegler Natta catalysts and effects on the production of polypropylene by gas chromatographic with simultaneous detection: Pulsed discharge helium ionization, mass spectrometry and flame ionization

  • Hernandez-Fernandez, Joaquin
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] This article describes a new simultaneous method for the analysis of sulfur-type poisons, hydrocarbons and permanent gases affecting the productivity of the Ziegler Natta catalyst during the synthesis of polypropylene on an industrial scale in a fluidized-bed reactor. The identification was achieved employing a configuration of the seven-valve chromatographic system, with events at different times, allowing distribution of the sample through multiple columns, and finally reaching the helium ionization detectors of pulsed discharge, flame ionization and mass spectrometry. The results obtained show a good precision of the method used because the variability was less than 1.02% in area and 0.49% in retention time for short term precision and longer term precision. The quantification of these species was successful after performing the calibration curve with the dynamic mixer showing an r(2) higher than 0.9945 and excellent linearity. The lowest LOD value was 0.01 mg kg(-1) for carbonyl sulphide, hydrogen sulfide, ethylmercaptan and propylmercaptan and the lowest LOQ was 0.03 mg kg(-1) for hydrogen sulfide. The highest LOD and LOQ values were for oxygen and carbon dioxide with 0.40 and 0.93 mg kg(-1) respectively. With this configuration, the correlation of data between the three detectors was simplified, having almost identical retention times for the analytes studied. The poisons detected and quantified in the samples were: hydrogen sulfide (0.1-0.5 mg kg(-1)), carbonyl sulphide (0.012-0.06 mg kg(-1)), carbon disulphide (0.04-0.22 mg kg(-1)), methylmercaptan (0.12-12.51 mg kg(-1)), ethylmercaptan (0.9-5.5 mg kg(-1)), carbon dioxide (0.10-3.0 mg kg(-1)), oxygen (0.55-6.1 mg kg(-1)), acetylene (0.15-3.5 mg kg(-1)) and methylacetylene (0.04-0.2 mg kg(-1)). The productivity losses were between 5 and 22%. (C) 2019 Elsevier B.V. All rights reserved.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

The Effect of Halloysite Nanotubes on the Fire Retardancy Properties of Partially Biobased Polyamide 610

  • Marset, David
  • Dolza, Celia
  • Fages, Eduardo
  • Gonga, Eloi
  • Gutiérrez, Óscar
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] The main objective of the work reported here was the analysis and evaluation of halloysite nanotubes (HNTs) as natural flame retardancy filler in partially biobased polyamide 610 (PA610), with 63% of carbon from natural sources. HNTs are naturally occurring clays with a nanotube-like shape. PA610 compounds containing 10%, 20%, and 30% HNT were obtained in a twin-screw co-rotating extruder. The resulting blends were injection molded to create standard samples for fire testing. The incorporation of the HNTs in the PA610 matrix leads to a reduction both in the optical density and a significant reduction in the number of toxic gases emitted during combustion. This improvement in fire properties is relevant in applications where fire safety is required. With regard to calorimetric cone results, the incorporation of 30% HNTs achieved a significant reduction in terms of the peak values obtained of the heat released rate (HRR), changing from 743 kW/m(2) to about 580 kW/m(2) and directly modifying the shape of the characteristic curve. This improvement in the heat released has produced a delay in the mass transfer of the volatile decomposition products, which are entrapped inside the HNTs' lumen, making it difficult for the sample to burn. However, in relation to the ignition time of the samples (TTI), the incorporation of HNTs reduces the ignition start time about 20 s. The results indicate that it is possible to obtain polymer formulations with a high renewable content such as PA610, and a natural occurring inorganic filler in the form of a nanotube, i.e., HNTs, with good flame retardancy properties in terms of toxicity, optical density and UL94 test., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacturing and compatibilization of PLA/PBAT binary blends by cottonseed oil-based derivatives

  • Carbonell-Verdu, A.
  • Dominici, F.
  • Torre, L.
  • Ferri, J.M|||0000-0002-1269-4973
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Balart, Rafael|||0000-0001-5670-7126
[EN] This research work aims at the compatibilization of poly(lactic acid)/poly(butylene adipate-co-terephthalate), PLA/PBAT binary blends by using cottonseed oil derivatives, i.e. epoxidized (ECSO) and maleinized (MCSO) cottonseed oil. The potential of these vegetable oil-based compatibilizers are compared versus the effects of a conventional styrene-acrylic oligomer. The base PLA/PBAT binary blend composition was 80 wt% PLA/20 wt% PBAT and the amount of compatibilizer was set to 1 and 7.5 wt%. The effects of the different compatibilizers were evaluated on PLA/PBAT films in terms of mechanical and thermal properties as well as blend's morphology by field emission scanning electron microscopy (FESEM). Complementary, biodisintegration tests in controlled compost soil and surface properties were evaluated to assess the effects of the compatibilizers. Addition of 1 wt% ECSO and MCSO led to a remarkable increase in the elongation at break up to values over 100% with regard to neat PLA. Despite this, maximum elongation at break was obtained for the compatibilized PLA/PBAT blend with 7.5 wt% MCSO, reaching values of about 321.2% respect neat PLA keeping mechanical resistant properties, such as Young's modulus and tensile strength, at high levels. Therefore, vegetable oil-derived compatibilizers stand out as environmentally friendly additives for PLA/PBAT binary blends with improved properties., This work was supported by the Ministry of Economy and Competitiveness (MINECO) (grant number MAT2017-84909-C2-2-R). A. Carbonell-Verdu wants to thank Universitat Politecnica de Valencia for financial support through an FPI grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Gum Rosin as a Size Control Agent of Poly(butylene adipate-co-terephthalate) (PBAT) Domains to Increase the Toughness of Packaging Formulations Based on Polylactic Acid (PLA)

  • Aldás-Carrasco, Miguel Fernando
  • Motoc, Dana Luca
  • PEPONI, LAURA
  • Arrieta, Marina Patricia
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Gum rosin (GR) was used as a natural additive to improve the compatibility between polylactic acid, PLA, and poly(butylene adipate-co-terephthalate, PBAT, blended with 20 wt.% of PBAT (PLA/PBAT). The PBAT was used as a soft component to increase the ductility of PLA and its fracture toughness. The coalescence of the PBAT domains was possible due to the plasticization effect of the GR component. These domains contributed to increasing the toughness of the final material due to the variation and control of the PBAT domains' size and consequently, reducing the stress concentration points. The GR was used in contents of 5, 10, 15, and 20 phr. Consequently, the flexural properties were improved and the impact resistance increased up to 80% in PLA/PBAT_15GR with respect to the PLA/PBAT formulation. Field emission scanning electron microscope (FESEM) images allowed observing that the size of PBAT domains of 2-3 mu m was optimal to reduce the impact stress. Differential scanning calorimetry (DSC) analysis showed a reduction of up to 8 degrees C on the PLA melting temperature and up to 5.3 degrees C of the PLA glass transition temperature in the PLA/PBAT_20GR formulation, which indicates an improvement in the processability of PLA. Finally, transparent films with improved oxygen barrier performance and increased hydrophobicity were obtained suggesting the potential interest of these blends for the food packaging industry, This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Toughened Poly(Lactic Acid) PLA Formulations by Binary Blends with Poly(Butylene Succinate-co-Adipate) PBSA and Their Shape Memory Behaviour

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This study reports the effect of poly(butylene succinate-co-adipate) (PBSA) on the mechanical performance and shape memory behavior of poly(lactic acid) (PLA) specimens that were manufactured by injection molding and hot-press molding. The poor miscibility between PLA and PBSA was minimized by the addition of an epoxy styrene-acrylic oligomer (ESAO), which was commercially named Joncryl®. It was incorporated during the extrusion process. Tensile, impact strength, and hardness tests were carried out following international standards. PLA/PBSA blends with improved mechanical properties were obtained, which highlighted the sample that was compatibilized with ESAO, leading to a remarkable enhancement in elongation at break, but showing poor shape memory behaviour. Field Emission Scanning Electron Microscopy (FESEM) images showed how the ductile properties were improved, while PBSA loading increased, thus leading to minimizing the brittleness of neat PLA. The differential scanning calorimetry (DSC) analysis revealed the low miscibility between these two polymers and the improving effect of PBSA in PLA crystallization. The bending test carried out on the sheets of PLA/PBSA blends showed the direct influence that the PBSA has on the reduction of the shape memory that is intrinsically offered by neat PLA., This research was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) program numbers MAT2017-84909-C2-2-R. L.Q.-C wants to thank GV for his FPI grant (ACIF/2016/182) and the MECD for his FPU grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental study of the auto-catalytic effect of triethylaluminum and TiCl4 residuals at the onset of non-additive polypropylene degradation and their impact on thermo-oxidative degradation and pyrolysis

  • Hernandez-Fernandez, Joaquin
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] In this article, the pyrolysis and thermo-oxidative degradation of five industrial waste products was carried out in a discontinuous quartz reactor at 550 ¿C under the auto-catalytic effect of residues of titanium tetrachloride (TiCl4), triethylaluminium (TEAL), and iron (Fe). We using the coupled on-site analysis of an GC¿MS/FID/ PDHID with 7 valves and 8 columns in series. The study also discusses the effect of the concentration of the catalyst residuals with the Eac (activation energy) and the evolution of the profile of permanent oxygenated gases, hydrocarbons and sulfurs, as well as the functional waste groups from decomposition during pyrolysis and thermo-oxidative degradation. The origin of the degradation and the beginnings of PP pyrolysis and thermooxidative degradation are explained by hydrolysis mechanisms and thermal reactions that imply successive reactions with these (TEAL), TiO2, and chloride residues, giving rise to ethyl radicals and explaining the formation of alcohols, ketones, carboxylic acids, alkynes and alkenes. The study also found that the gaseous profiles are very consistent with the DTG curves and the Eac, in terms of the appearance of peaks and relevant stages throughout the total temperature range. The effect of Cl, Fe and TEAL on the PP degradation is very high upon passing from an inert to an oxidative atmosphere. This reduces the content of hydrocarbons and oxygenates to CO2 between 49 and 66% because of the attack of the oxygen atom. In the pyrolysis the propylene content oscillates between 42 and 56%. Finally, the initial reaction mechanisms, and the secondary reaction routes, are proposed and demonstrated experimentally in function of the primary volatile compounds quantified. The thermo-oxidative properties of the five PP waste products improve significantly with the addition of 0.1% of a secondary antioxidant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacturing and Properties of Binary Blend from Bacterial Polyester Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) and Poly(caprolactone) with Improved Toughness

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Verdu, Isabel
[EN] Polyhydroxyalkanoates (PHAs) represent a promising group of bacterial polyesters for new applications. Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) is a very promising bacterial polyester with potential uses in the packaging industry; nevertheless, as with many (almost all) bacterial polyesters, PHBH undergoes secondary crystallization (aging) which leads to an embrittlement. To overcome or minimize this, in the present work a flexible petroleum-derived polyester, namely poly(e-caprolactone), was used to obtain PHBH/PCL blends with different compositions (from 0 to 40 PCL wt %) using extrusion followed by injection moulding. The thermal analysis of the binary blends was studied by means of differential scanning calorimetry (DSC) and thermogravimetry (TGA). Both TGA and DSC revealed immiscibility between PHBH and PCL. Mechanical dynamic thermal analysis (DMTA) allowed a precise determination of the glass transition temperatures (Tg) as a function of the blend composition. By means of field emission scanning electron microscopy (FESEM), an internal structure formed by two phases was observed, with a PHBH-rich matrix phase and a finely dispersed PCL-rich phase. These results confirmed the immiscibility between these two biopolymers. However, the mechanical properties obtained through tensile and Charpy tests, indicated that the addition of PCL to PHBH considerably improved toughness. PHBH/PCL blends containing 40 PCL wt % offered an impact resistance double that of neat PHBH. PCL addition also contributed to a decrease in brittleness and an improvement in toughness and some other ductile properties. As expected, an increase in ductile properties resulted in a decrease in some mechanical resistant properties, e.g., the modulus and the strength (in tensile and flexural conditions) decreased with increasing wt % PCL in PHBH/PCL blends., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU), project numbers MAT2017-84909-C2-2-R. This work was supported by the POLISABIO program, grant number (2019-A02). Juan Ivorra-Martinez is the recipient of an FPI grant from Universitat Politècnica de València (PAID-2019-SP20190011). Luis Quiles-Carrillo wants to thank GVA for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Films Based on Mater-Bi(R) Compatibilized with Pine Resin Derivatives: Optical, Barrier, and Disintegration Properties

  • Aldás-Carrasco, Miguel Fernando
  • Arrieta, Marina Patricia
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • Ferri, J.M|||0000-0002-1269-4973
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Mater-Bi(R) NF866 (MB) was blended with gum rosin and two pentaerythritol esters of gum rosin (labeled as LF and UT), as additives, to produce biobased and compostable films for food packaging or agricultural mulch films. The films were prepared by blending MB with 5, 10, and 15 wt.% of each additive. The obtained films were characterized by optical, colorimetric, wettability, and oxygen barrier properties. Moreover, the additives and the MB-based films were disintegrated under composting conditions and the effect of each additive on the biodegradation rate was studied. All films were homogeneous and optically transparent. The color of the films tended to yellow tones due to the addition of pine resin derivatives. All the formulated films presented a complete UV-transmittance blocking effect in the UVA and UVB region, and those with 5 wt.% of pine resin derivatives increased the MB hydrophobicity. Low amounts of resins tend to maintain the oxygen transmission rate (OTR) values of the neat MB, due to its good solubilizing and compatibilizing effects. The disintegration under composting conditions test revealed that gum rosin completely disintegrates in about 90 days, while UT degrades 80% and LF degrades 5%, over 180 days of incubation. As expected, the same tendency was obtained for the disintegration of the studied films, although Mater-Bi(R) reach 28% of disintegrability over the 180 days of the composting test., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), projects: PROMADEPCOL (MAT2017-84909-C2-2-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of PLA film ductility by plasticization with epoxidized karanja oil

  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Carbonell-Verdu, A.
  • Arrieta, Marina Patricia
[EN] In this work, karanja oil has been epoxidized and further used as biobased plasticizer to improve some properties of poly (lactic acid) (PLA). The use of epoxidized karanja oil (EKO) has been studied because karanja oil is used in organic farming as an insecticide and generating an epoxidation of the oil can act as a PLA plasticizer. Melt extrusion was used to plasticize PLA with different EKO amounts in the 0e10 wt%. The formulations with EKO decrease the glass transition temperature as the EKO content increases and, in addition, generates an increase in elongation at break. Plasticizer saturation is observed by scanning electron microscopy (SEM) above 5% of EKO. PLA formulation with 5 wt% shows an optimal balance between the improvement of the fragility of the material, improving the elongation at breakage by 77%, using a relatively small concentration of plasticizer. Moreover, all materials were disintegrated under composting conditions at laboratory scale level., This research was supported by the Ministry of Economy and Competitiveness (MINECO) [MAT2017-84909-C2-2-R] and Santander-UCM (PR87/19e22628). D. Garcia-Garcia wants to thanks the Generalitat Valenciana for their financial support through a post-doctoral grant (APOSTD/2019/201). M.P. Arrieta acknowledge for Juan de la Cierva (FJCI-2017-33536) contract from the MINECO.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Ultraviolet Radiation Exposure Time on Styrene-Ethylene-Butadiene-Styrene (SEBS) Copolymer

  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Crespo, J.E|||0000-0003-1372-4289
  • Parres, F.|||0000-0002-1083-9526
  • Samper, María-Dolores|||0000-0002-5102-8412
[EN] The effect of ultraviolet radiation on styrene-ethylene-butadiene-styrene (SEBS) has been studied at different exposures times in order to obtain a better understanding of the mechanism of ageing. The polymer materials were mechanically tested and then their surfaces were analyzed using a scanning electron microscope (SEM) and atomic force microscopy (AFM). Moreover, the optical analysis of contact angle (OCA) was used to evaluate the surface energy (gamma(s)) and the yellowing index (YI) and attenuated total reflectance infrared spectroscopy (ATR-FTIR) were used to observe structural and physical changes in aging SEBS. The results obtained for the SEBS, in relation to the duration of exposure, showed superficial changes that cause a decrease in the surface energy (gamma(s)) and, therefore, a decrease in surface roughness. This led to a reduction in mechanical performance, decreasing the tensile strength by about 50% for exposure times of around 200 hours., This work was supported by the Ministry of Economy and Competitiveness (MINECO) grant number MAT2017-84909-C2-2-R). Daniel Garcia-Garcia acknowledges Generalitat Valenciana (GVA) for financial support through a postdoctoral contract (APOSTD/2019/201).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ductility and Toughness Improvement of Injection-Molded Compostable Pieces of Polylactide by Melt Blending with Poly(e-caprolactone) and Thermoplastic Starch

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
  • Jorda-Vilaplana, Amparo
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Pineiro, Federico
[EN] The present study describes the preparation and characterization of binary and ternary blends based on polylactide (PLA) with poly("-caprolactone) (PCL) and thermoplastic starch (TPS) to develop fully compostable plastics with improved ductility and toughness. To this end, PLA was first melt-mixed in a co rotating twin-screw extruder with up to 40 wt % of different PCL and TPS combinations and then shaped into pieces by injection molding. The mechanical, thermal, and thermomechanical properties of the resultant binary and ternary blend pieces were analyzed and related to their composition. Although the biopolymer blends were immiscible, the addition of both PCL and TPS remarkably increased the flexibility and impact strength of PLA while it slightly reduced its mechanical strength. The most balanced mechanical performance was achieved for the ternary blend pieces that combined high PCL contents with low amounts of TPS, suggesting a main phase change from PLA/TPS (comparatively rigid) to PLA/PCL (comparatively flexible). The PLA-based blends presented an ¿island-and-sea¿ morphology in which the TPS phase contributed to the fine dispersion of PCL as micro-sized spherical domains that acted as a rubber-like phase with the capacity to improve toughness. In addition, the here-prepared ternary blend pieces presented slightly higher thermal stability and lower thermomechanical stiffness than the neat PLA pieces. Finally, all biopolymer pieces fully disintegrated in a controlled compost soil after 28 days. Therefore, the inherently low ductility and toughness of PLA can be successfully improved by melt blending with PCL and TPS, resulting in compostable plastic materials with a great potential in, for instance, rigid packaging applications., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) program numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R, and by the EU H2020 project YPACK (reference number 773872).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Silane-Functionalized Sheep Wool Fibers from Dairy Industry Waste for the Development of Plasticized PLA Composites with Maleinized Linseed Oil for Injection-Molded Parts

  • Pawlak, Franciszek
  • Aldas, Miguel
  • Arrieta, Marina Patricia
  • Parres, F.|||0000-0002-1083-9526
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Poly(lactic acid) (PLA) was plasticized with maleinized linseed oil (MLO) and further reinforced with sheep wool fibers recovered from the dairy industry. The wool fibers were firstly functionalized with 1 and 2.5 phr of tris(2-methoxyethoxy)(vinyl) (TVS) silane coupling agent and were further used in 1, 5, and 10 phr to reinforce the PLA/MLO matrix. Then, the composite materials were processed by extrusion, followed by injection-molding processes. The mechanical, thermal, microstructural, and surface properties were assessed. While the addition of untreated wool fibers to the plasticized PLA/MLO matrix caused a general decrease in the mechanical properties, the TVS treatment was able to slightly compensate for such mechanical losses. Additionally, a shift in cold crystallization and a decrease in the degree of crystallization were observed due to the fiber silane modification. The microstructural analysis confirmed enhanced interaction between silane-modified fibers and the polymeric matrix. The inclusion of the fiber into the PLA/MLO matrix made the obtained material more hydrophobic, while the yellowish color of the material increased with the fiber content., This research was funded by MINECO under projects: PROMADEPCOL: MAT2017-84909-C2-2-R and CTM2017-88989-P as well as by European Union s Horizon 2020 research and innovation program under grant agreement no. 860407 BIO-PLASTICS EUROPE.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacturing and Characterization of Green Composites with Partially Biobased Epoxy Resin and Flaxseed Flour Wastes

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Rojas-Lema, Sandra Paola
[EN] In the present work, green¿composites from a partially biobased epoxy resin (BioEP) reinforced with lignocellulosic particles, obtained from flax industry by¿products or wastes, have been manufactured by casting. In this study, the flaxseed has been crushed by two different mechanical milling processes to achieve different particle sizes, namely coarse size (CFF), and fine size (FFF) particle flaxseed flour, with a particle size ranging between 100¿220 ¿m and 40¿140 ¿m respectively. Subsequently, different loadings of each particle size (10, 20, 30, and 40 wt%) were mixed with the BioEP resin and poured into a mold and subjected to a curing cycle to obtain solid samples for mechanical, thermal, water absorption, and morphological characterization. The main aim of this research was to study the effect of the particle size and its content on the overall properties of composites with BioEP. The results show that the best mechanical properties were obtained for composites with a low reinforcement content (10 wt%) and with the finest particle size (FFF) due to a better dispersion into the matrix, and a better polymer¿particle interaction too. This also resulted in a lower water absorption capacity due to the presence of fewer voids in the developed composites. Therefore, this study shows the feasibility of using flax wastes from the seeds as a filler in highly environmentally friendly composites with a wood¿like appearance with potential use in furniture or automotive sectors., This research was funded by Spanish Ministry of Science, Innovation, and Universities (MICIU), project numbers MAT2017-84909-C2-2-R. This work was supported by the POLISABIO program grant number (2019-A02). D. Lascano thanks Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. D. Garcia-Garcia wants to thank Generalitat Valenciana (GVA) for their financial support through a post-doctoral grant (APOSTD/2019/201). S. Rojas-Lema is a recipient of a Santiago Grisolía contract (GRISOLIAP/2019/132) from GVA. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhanced Interfacial Adhesion of Polylactide/Poly(e-caprolactone)/Walnut Shell Flour Composites by Reactive Extrusion with Maleinized Linseed Oil

  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Montanes, Nestor|||0000-0001-6070-127X
  • Richart, Nuria
[EN] Novel green composites were prepared by melt compounding a binary blend of polylactide (PLA) and poly("-caprolactone) (PCL) at 4/1 (wt/wt) with particles of walnut shell flour (WSF) in the 10¿40 wt % range, which were obtained as a waste from the agro-food industry. Maleinized linseed oil (MLO) was added at 5 parts per hundred resin (phr) of composite to counteract the intrinsically low compatibility between the biopolymer blend matrix and the lignocellulosic fillers. Although the incorporation of WSF tended to reduce the mechanical strength and thermal stability of PLA/PCL, the MLO-containing composites filled with up to 20 wt % WSF showed superior ductility and a more balanced thermomechanical response. The morphological analysis revealed that the performance improvement attained was related to a plasticization phenomenon of the biopolymer blend and, more interestingly, to an enhancement of the interfacial adhesion of the green composites achieved by extrusion with the multi-functionalized vegetable oil., This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers AGL2015-63855-C2-1-R and MAT2017-84909-C2-2-R. L.Q.-C. holds a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) whereas S.T.-G. is a recipient of a Juan de la Cierva Incorporación contract (IJCI-2016-29675) from MICIU.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

In Situ Compatibilization of Biopolymer Ternary Blends by Reactive Extrusion with Low-Functionality Epoxy-Based Styrene Acrylic Oligomer

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Lagaron, J.M.
[EN] The present study reports on the use of low-functionality epoxy-based styrene¿acrylic oligomer (ESAO) to compatibilize immiscible ternary blends made of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), polylactide (PLA), and poly(butylene adipate-co-terephthalate) (PBAT). The addition during melt processing of low-functionality ESAO at two parts per hundred resin (phr) of biopolymer successfully changed the soften inclusion phase in the blend system to a thinner morphology, yielding biopolymer ternary blends with higher mechanical ductility and also improved oxygen barrier performance. The compatibilization achieved was ascribed to the in situ formation of a newly block terpolymer, i.e. PHBVb- PLA-b-PBAT, which was produced at the blend interface by the reaction of the multiple epoxy groups present in ESAO with the functional terminal groups of the biopolymers. This chemical reaction was mainly linear due to the inherently low functionality of ESAO and the more favorable reactivity of the epoxy groups with the carboxyl groups of the biopolymers, which avoided the formation of highly branched and/or cross-linked structures and thus facilitated the films processability. Therefore, the reactive blending of biopolymers at different mixing ratios with low-functionality ESAO represents a straightforward methodology to prepare sustainable plastics at industrial scale with different physical properties that can be of interest in, for instance, food packaging applications., This research was funded by the EU H2020 project YPACK (Reference number 773872) and by the Spanish Ministry of Science, Innovation, and Universities (MICIU) with project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. L. Quiles-Carrillo wants to thank the Spanish Ministry of Education, Culture, and Sports (MECD) for financial support through his FPU Grant Number FPU15/03812. Torres-Giner also acknowledges the MICIU for his Juan de la Cierva contract (IJCI-2016-29675).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A comparative study on the effect of different reactive compatibilizers on injection-molded pieces of bio-based high-density polyethylene/polylactide blends

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
  • Jorda-Vilaplana, Amparo
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] The present study reports on the development of binary blends consisting of bio-based high-density polyethylene (bio-HDPE) with polylactide (PLA), in the 5¿20 wt % range, prepared by melt compounding and then shaped into pieces by injection molding. In order to enhance the miscibility between the green polyolefin and the biopolyester, different reactive compatibilizers were added during the melt-blending process, namely polyethylene grafted maleic anhydride (PE-g-MA), poly(ethylene-co-glycidyl methacrylate) (PE-co-GMA), maleinized linseed oil (MLO), and a combination of MLO with dicumyl peroxide (DCP). Among the tested compatibilizers, the dual addition of MLO and DCP provided the binary blend pieces with the most balanced mechanical performance in terms of rigidity and impact strength as well as the highest thermal stability. The fracture surface of the binary blend piece processed with MLO and DCP revealed the formation of a continuous structure in which the dispersed PLA phase was nearly no discerned in the bio-HDPE matrix. The resultant miscibility improvement was ascribed to both the high solubility and plasticizing effect of MLO on the PLA phase as well as the crosslinking effect of DCP on both biopolymers. The latter effect was particularly related to the formation of macroradicals of each biopolymer that, thereafter, led to the in situ formation of bio HDPE-co-PLA copolymers and also to the development of a partially crosslinked network in the binary blend. As a result, cost-effective and fully bio-based polymer pieces with improved mechanical strength, high toughness, and enhanced thermal resistance were obtained., This research was funded by the EU H2020 project YPACK (reference number 773872) and by the Ministry of Science, Innovation, and Universities (MICIU, project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R). Quiles-Carrillo and Torres-Giner are recipients of a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) and a Juan de la Cierva contract (IJCI-2016-29675) from the MICIU, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dynamic-Mechanical and Decomposition Properties of Flax/Basalt Hybrid Laminates Based on an Epoxidized Linseed Oil Polymer

  • Motoc, Dana Luca
  • Ferri, J.M|||0000-0002-1269-4973
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Balart, Rafael|||0000-0001-5670-7126
[EN] This contribution focuses on the development of flax and flax/basalt hybrid reinforced composites based on epoxidized linseed oil (ELO) resin, exploiting the feasibility of different ratios of glutaric anhydride (GA) to maleinized linseed oil (MLO) in the hardener system (50:0, 40:10 and 30:20 wt.%) to provide crosslinked thermosets with balanced properties. The hybrid laminates have been manufactured by resin transfer molding (RTM) and subjected to dynamic-mechanical (DMA) and thermal gravimetry (TGA) analysis. The presence of glutaric anhydride (GA) resulted in hard and relatively brittle flax and flax/basalt laminates, whose loss moduli decreased as the number of basalt plies diminished. Furthermore, the increase in MLO content in the GA:MLO hardener system shifted the glass transition temperatures (T-g) from 70 degrees C to 59 and 56 degrees C, which is representative of a decrease in brittleness of the crosslinked resin. All samples exhibited two stages of their decomposition process irrespective of the MLO content. The latter influenced the residual mass content that increased with the increase of the MLO wt.% from 10 to 30 wt.%, with shifts of the final degradation temperatures from 410 degrees C to 425 degrees C and 445 degrees C, respectively., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improved Toughness in Lignin/Natural Fiber Composites Plasticized with Epoxidized and Maleinized Linseed Oils

  • Dominici, Franco
  • Carbonell-Verdu, Alfredo
  • Luzi, Francesca
  • Torre, Luigi
  • Puglia, Debora
  • Samper, María-Dolores|||0000-0002-5102-8412
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] The use of maleinized (MLO) and epoxidized (ELO) linseed oils as potential biobased plasticizers for lignin/natural fiber composites formulations with improved toughness was evaluated. Arboform®, a lignin/natural fiber commercial composite, was used as a reference matrix for the formulations. The plasticizer content varied in the range 0¿15 wt % and mechanical, thermal and morphological characterizations were used to assess the potential of these environmentally friendly modifiers. Results from impact tests show a general increase in the impact-absorbed energy for all the samples modified with bio-oils. The addition of 2.5 wt % of ELO to Arboform (5.4 kJ/m2) was able to double the quantity of absorbed energy (11.1 kJ/m2) and this value slightly decreased for samples containing 5 and 10 wt %. A similar result was obtained with the addition of MLO at 5 wt %, with an improvement of 118%. The results of tensile and flexural tests also show that ELO and MLO addition increased the tensile strength as the percentage of both oils increased, even if higher values were obtained with lower percentages of maleinized oil due to the possible presence of ester bonds formed between multiple maleic groups present in MLO and the hydroxyl groups of the matrix. Thermal characterization confirmed that the mobility of polymer chains was easier in the presence of ELO molecules. On the other hand, MLO presence delayed the crystallization event, predominantly acting as an anti-nucleating agent, interrupting the folding or packing process. Both chemically modified vegetable oils also efficiently improved the thermal stability of the neat matrix.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Manufacturing and Characterization of Functionalized Aliphatic Polyester from Poly(lactic acid) with Halloysite Nanotubes

  • Montava-Jorda, Sergi|||0000-0002-5378-0333
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Montanes, Nestor|||0000-0001-6070-127X
  • Chacon, Victor
[EN] This work reports the potential of poly(lactic acid)-PLA composites with different halloysite nanotube (HNTs) loading (3, 6 and 9 wt%) for further uses in advanced applications as HNTs could be used as carriers for active compounds for medicine, packaging and other sectors. This work focuses on the effect of HNTs on mechanical, thermal, thermomechanical and degradation of PLA composites with HNTs. These composites can be manufactured by conventional extrusion-compounding followed by injection molding. The obtained results indicate a slight decrease in tensile and flexural strength as well as in elongation at break, both properties related to material cohesion. On the contrary, the stiffness increases with the HNTs content. The tensile strength and modulus change from 64.6 MPa/2.1 GPa (neat PLA) to 57.7/2.3 GPa MPa for the composite with 9 wt% HNTs. The elongation at break decreases from 6.1% (neat PLA) down to a half for composites with 9 wt% HNTs. Regarding flexural properties, the flexural strength and modulus change from 116.1 MPa and 3.6 GPa respectively for neat PLA to values of 107.6 MPa and 3.9 GPa for the composite with 9 wt% HNTs. HNTs do not affect the glass transition temperature with invariable values of about 64 degrees C, or the melt peak temperature, while they move the cold crystallization process towards lower values, from 112.4 degrees C for neat PLA down to 105.4 degrees C for the composite containing 9 wt% HNTs. The water uptake has been assessed to study the influence of HNTs on the water saturation. HNTs contribute to increased hydrophilicity with a change in the asymptotic water uptake from 0.95% (neat PLA) up to 1.67% (PLA with 9 wt % HNTs) and the effect of HNTs on disintegration in controlled compost soil has been carried out to see the influence of HNTs on this process, which is a slight delay on it. These PLA-HNT composites show good balanced properties and could represent an interesting solution to develop active materials., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) through the MAT2017-84909-C2-2-R program number. D. Lascano wants to thank UPV for the grant received though the PAID-01-18 program. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of microwave-assisted extraction of phenolic compounds with antioxidant activity from carob pods

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Mellinas, Cristina
  • Garrigos, M.C.
[EN] A microwave-assisted extraction (MAE) procedure to obtain phenolic compounds from carob bark was optimized by using response surface methodology. A four-factor, three-level Box-Behnken design with five central points was used to evaluate the influence of temperature, solid-liquid ratio, ethanol concentration and time in carob bark extraction in terms of antioxidant activity (DPPH) and total extraction yield. Optimal extraction conditions were found using 80 ºC, 35% (v/v) ethanol, a ratio of 35 mL/g and 29.5 min. Total phenolics content (TPC), antioxidant activity (DPPH, FRAP, ABTS), carbohydrates content and main polyphenols composition (HPLC) were determined at optimal conditions. An experimental total yield of 66.5% was obtained with a TPC value of 33.6 mg GAE/g DW and polysaccharides content of 345.4 mg glucose/g DW. A high antioxidant activity was also shown by the three methods tested. The results showed the potential of carob pods skin as a natural source of phenolic compounds, in particular gallic acid, and the effectiveness of MAE as extraction technique for the revalorization of this agro-food waste., This research was supported by the Spanish Ministry of Science, Innovation and Universities (MICIU) programs MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R and by the EU H2020 project YPACK (reference number 773872). Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Torres-Giner also thank MINECO for his Juan de la Cierva contract (IJCI-2016-29675).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A New Route of Valorization of Petrochemical Wastewater: Recovery of 1,3,5-Tris (4-tert-butyl-3-hydroxy-2,6-dimethyl benzyl)¿1,3,5-triazine-2,4,6-(1H,3H,5H)-trione (Cyanox 1790) and Its Subsequent Application in a PP Matrix to Improve Its Thermal Stability

  • Hernández-Fernández, Joaquin
  • Ortega-Toro, Rodrigo
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] The various chemicals in industrial wastewater can be beneficial for improving its circularity. If extraction methods are used to capture valuable components from the wastewater and then recirculate them throughout the process, the potential of the wastewater can be fully exploited. In this study, wastewater produced after the polypropylene deodorization process was evaluated. These waters remove the remains of the additives used to create the resin. With this recovery, contamination of the water bodies is avoided, and the polymer production process becomes more circular. The phenolic component was recovered by solid-phase extraction and HPLC, with a recovery rate of over 95%. FTIR and DSC were used to evaluate the purity of the extracted compound. After the phenolic compound was applied to the resin and its thermal stability was analyzed via TGA, the compound's efficacy was finally determined. The results showed that the recovered additive improves the thermal qualities of the material., This research was partially funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R Nanolignin.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the Use of Phenolic Compounds Present in Citrus Fruits and Grapes as Natural Antioxidants for Thermo-Compressed Bio-Based High-Density Polyethylene Films

  • Rojas-Lema, Sandra Paola
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Balart, Rafael|||0000-0001-5670-7126
[EN] This study originally explores the use of naringin (NAR), gallic acid (GA), caffeic acid (CA), and quercetin (QUER) as natural antioxidants for bio-based high-density polyethylene (bio-HDPE). These phenolic compounds are present in various citrus fruits and grapes and can remain in their leaves, peels, pulp, and seeds as by-products or wastes after juice processing. Each natural additive was first melt-mixed at 0.8 parts per hundred resin (phr) of bio-HDPE by extrusion and the resultant pellets were shaped into films by thermo-compression. Although all the phenolic compounds colored the bio-HDPE films, their contact transparency was still preserved. The chemical analyses confirmed the successful inclusion of the phenolic compounds in bio-HDPE, though their interaction with the green polyolefin matrix was low. The mechanical performance of the bio-HDPE films was nearly unaffected by the natural compounds, presenting in all cases a ductile behavior. Interestingly, the phenolic compounds successfully increased the thermo-oxidative stability of bio-HDPE, yielding GA and QUER the highest performance. In particular, using these phenolic compounds, the onset oxidation temperature (OOT) value was improved by 43 and 41.5 ºC, respectively. Similarly, the oxidation induction time (OIT) value, determined in isothermal conditions at 210 ºC, increased from 4.5 min to approximately 109 and 138 min. Furthermore, the onset degradation temperature in air of bio-HDPE, measured for the 5% of mass loss (T5%), was improved by up to 21 ºC after the addition of NAR. Moreover, the GA- and CA-containing bio-HDPE films showed a high antioxidant activity in alcoholic solution due to their favored release capacity, which opens up novel opportunities in active food packaging. The improved antioxidant performance of these phenolic compounds was ascribed to the multiple presence of hydroxyl groups and aromatic heterocyclic rings that provide these molecules with the features to permit the delocalization and the scavenging of free radicals. Therefore, the here-tested phenolic compounds, in particular QUER, can represent a sustainable and cost-effective alternative of synthetic antioxidants in polymer and biopolymer formulations, for which safety and environmental issues have been raised over time, This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Kinetic Analysis of the Thermal Degradation of Recycled Acrylonitrile-Butadiene-Styrene by non-Isothermal Thermogravimetry

  • Balart, Rafael|||0000-0001-5670-7126
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] This work presents an in-depth kinetic study of the thermal degradation of recycled acrylonitrile-butadiene-styrene (ABS) polymer. Non-isothermal thermogravimetric analysis (TGA) data in nitrogen atmosphere at different heating rates comprised between 2 and 30 K min¿1 were used to obtain the apparent activation energy (Ea) of the thermal degradation process of ABS by isoconversional (differential and integral) model-free methods. Among others, the differential Friedman method was used. Regarding integral methods, several methods with different approximations of the temperature integral were used, which gave different accuracies in Ea. In particular, the Flynn-Wall-Ozawa (FWO), the Kissinger-Akahira-Sunose (KAS), and the Starink methods were used. The results obtained by these methods were compared to the Kissinger method based on peak temperature (Tm) measurements at the maximum degradation rate. Combined Kinetic Analysis (CKA) was also carried out by using a modified expression derived from the general Sestak-Berggren equation with excellent results compared with the previous methods. Isoconversional methods revealed negligible variation of Ea with the conversion. Furthermore, the reaction model was assessed by calculating the characteristic "y(¿)" and "z(¿)" functions and comparing them with some master plots, resulting in a nth order reaction model with n = 1.4950, which allowed calculating the pre-exponential factor (A) of the Arrhenius constant. The results showed that Ea of the thermal degradation of ABS was 163.3 kJ mol¿1, while ln A was 27.5410 (A in min¿1). The predicted values obtained by integration of the general kinetic expression with the calculated kinetic triplet were in full agreement with the experimental data, thus giving evidence of the accuracy of the obtained kinetic parameters., This research was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) program numbers MAT2017-84909-C2-2-R. L.Q.-C. wants to thank the Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812), while S.T.-G. is a recipient of a Juan de la Cierva - Incorporacion contract (IJCI-2016-29675) from MINECO.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of different compatibilizers on environmentally friendly composites from poly(lactic acid) and diatomaceous earth

  • Agüero-Rodríguez, Ángel
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Jorda-Vilaplana, Amparo
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] Environmentally friendly composites from poly(lactic acid) (PLA) and diatomaceous earth (DE) were successfully manufactured by extrusion, followed by injection moulding. DE was used as a filler; several compatibilizer/coupling agents, namely (3-glycidyloxypropyl)trimethoxysilane, epoxy styrene acrylic oligomer and maleinized linseed oil, were used to improve polymer¿filler interactions. Mechanical characterization was carried out by standard tensile, impact and hardness tests while morphological characterization of the fractured surfaces was conducted by field emission scanning electron microscopy. The effect of DE was evaluated by differential scanning calorimetry and dynamic mechanical thermal behaviour. The results show that the addition of DE provides an improved tensile modulus and induces more brittle composites due to stress concentration phenomena. The addition of compatibilizers in PLA-DE positively contributes to improve ductile properties, thus leading to high environmental efficiency materials with balancedmechanical properties. Specifically, the compatibility improvement between the PLA and DE was good with maleinized linseed oil and contributed to improving the impact strength, which is a key factor in PLA-based composites due to the intrinsic brittleness of neat PLA., This research was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) program number MAT2017-84909-C2-2-R. L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and the MECD for his FPU grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Deposition of gum rosin microspheres on polypropylene microfibres used in face masks to enhance their hydrophobic behaviour

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • E. Rayón|||0000-0002-0653-2046
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Aldás-Carrasco, Miguel Fernando
  • Arrieta, Marina Patricia
[EN] The present study aims to investigate the effects of gum rosin (GR) microspheres coating over the hydrophobicity of the outer layer of a polypropylene (PP) based surgical face mask. The gum rosin coating was deposited over the surface of the face mask outer layer by electrospraying technique. The deposition of GR microspheres was confirmed by field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR) analysis. The thermal analysis determined a cooperative effect between the microspheres and the mask fibre to increase the maximum degradation rate temperature and the onset degradation temperature. To follow the effect of the GR microspheres coating over the hydrophobicity of the surgical face mask, FESEM and wettability analyses were conducted before and after 3, 6, and 9 h of wearing time. In the FESEM image, it was seen that the microsphere was homogeneously distributed over the nonwoven fibre and its presence increases the roughness of the fibres due to the bulge of microspheres. The wettability measurements suggest that the microspheres coating helps to keep the original hydrophobicity of the outer layer of the surgical face mask even after 6 h of wearing time. Indeed, after 9 h of wearing time, the water contact angle (WCA) of the GR coated face mask is higher than the WCA of the surgical face mask without the coating at 3 h of wearing time. Therefore, the gun rosin microspheres coating improved the hydrophobicity of the surgical face mask which may allow improved protection and/or extended lifetime of use., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R). Cristina Pavon thanks Santiago Grisolía fellowship (GRISOLIAP/2019/113) from Generalitat Valenciana. Miguel Aldas thanks Secretaria de Educación Superior, Ciencia, Tecnología e Innovación (SENESCYT, Ecuador) and Escuela Politécnica Nacional.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Torrefaction of Coffee Husk Flour for the Development of Injection-Molded Green Composite Pieces of Polylactide with High Sustainability

  • Ortiz-Barajas, Diana L.
  • Arévalo-Prada, Johan A.
  • Rueda-Ordóñez, Yesid J.
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Coffee husk, a major lignocellulosic waste derived from the coffee industry, was first ground into flour of fine particles of approximately 90 mu m and then torrefied at 250 degrees C to make it more thermally stable and compatible with biopolymers. The resultant torrefied coffee husk flour (TCHF) was thereafter melt-compounded with polylactide (PLA) in contents from 20 to 50 wt% and the extruded green composite pellets were shaped by injection molding into pieces and characterized. Although the incorporation of TCHF reduced the ductility and toughness of PLA, filler contents of 20 wt% successfully yielded pieces with balanced mechanical properties in both tensile and flexural conditions and improved hardness. Contents of up to 30 wt% of TCHF also induced a nucleating effect that favored the formation of crystals of PLA, whereas the thermal degradation of the biopolyester was delayed by more than 7 degrees C. Furthermore, the PLA/TCHF pieces showed higher thermomechanical resistance and their softening point increased up to nearly 60 degrees C. Therefore, highly sustainable pieces were developed through the valorization of large amounts of coffee waste subjected to torrefaction. In the Circular Bioeconomy framework, these novel green composites can be used in the design of compostable rigid packaging and food contact disposables., This research work was funded by the Spanish Ministry of Science and Innovation (MICI), project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R, and by the Industrial University of Santander.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Peroxide-Induced Synthesis of Maleic Anhydride-Grafted Poly(butylene succinate) and Its Compatibilizing Effect on Poly(butylene succinate)/Pistachio Shell Flour Composites

  • Rojas-Lema, Sandra Paola
  • Arévalo-Aguado, Jordi|||0000-0002-0669-0933
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Framing the Circular Bioeconomy, the use of reactive compatibilizers was applied in order to increase the interfacial adhesion and, hence, the physical properties and applications of green composites based on biopolymers and food waste derived lignocellulosic fillers. In this study, poly(butylene succinate) grafted with maleic anhydride (PBS-g-MAH) was successfully synthetized by a reactive melt-mixing process using poly(butylene succinate) (PBS) and maleic anhydride (MAH) that was induced with dicumyl peroxide (DCP) as a radical initiator and based on the formation of macroradicals derived from the hydrogen abstraction of the biopolymer backbone. Then, PBS-g-MAH was used as reactive compatibilizer for PBS filled with different contents of pistachio shell flour (PSF) during melt extrusion. As confirmed by Fourier transform infrared (FTIR), PBS-g-MAH acted as a bridge between the two composite phases since it was readily soluble in PBS and could successfully form new esters by reaction of its multiple MAH groups with the hydroxyl (-OH) groups present in cellulose or lignin of PSF and the end ones in PBS. The resultant compatibilized green composites were, thereafter, shaped by injection molding into 4-mm thick pieces with a wood-like color. Results showed significant increases in the mechanical and thermomechanical rigidity and hardness, meanwhile variations on the thermal stability were negligible. The enhancement observed was related to the good dispersion and the improved filler-matrix interfacial interactions achieved by PBS-g-MAH and also to the PSF nucleating effect that increased the PBS's crystallinity. Furthermore, water uptake of the pieces progressively increased as a function of the filler content, whereas the disintegration in controlled compost soil was limited due to their large thickness., This research was funded by the Ministry of Science and Innovation (MICI) project number MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of mechanical and thermal properties of poly(3-hydroxybutyrate) (PHB) blends with surface-modified halloysite nanotubes (HNT)

  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Fombuena, Vicent|||0000-0001-7266-6205
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Balart, Rafael|||0000-0001-5670-7126
[EN] The effect of two hydrophobic treatments on the hydrophilic nature of halloysite nanotubes (HNT) was studied in this research work: a silanization with (3-glycidyloxypropyl) trimethoxysilane (GLYMO) and a surface treatment with a natural aromatic compound, i.e. caffeic acid (CA). In addition, the effect of 3¿wt% of unmodified HNT, silanized HNT (HNTSIL) and caffeic acid-modified HNT (HNTCA) on mechanical, thermal and morphological properties of a binary blend of poly(3-hydroxybutyrate) (PHB) and poly(¿-caprolactone) (PCL) with a weight ratio of 75/25, respectively was evaluated. These blends and their corresponding composites with HNT were partially compatibilized by reactive extrusion with dicumyl peroxide (DCP) and further processed by injection molding. The effectiveness of the surface treatments on HNT was followed by Fourier transformed infrared spectroscopy (FTIT), thermogravimetric analysis (TGA), field emission scanning electron microscopy (FESEM) and contact angle measurements. The obtained results suggested a clear hydrophobizing effect of both surface treatments on HNT but the hydrophobic nature the caffeic acid treatment can provide to HNT is greater than silanization. FESEM study on HNT-loaded PHB/PCL blends showed increased compatibility between modified-HNT and the polymeric matrix, as well as a better particle dispersion. In particular, 3¿wt% HNTCA lead to an increase in tensile strength and elongation at break of 11.4% and 74%, respectively, with regard to composites with unmodified HNT. In addition, thermal analysis, evaluated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), revealed a decrease in the melt peak temperature of 6.5¿°C for composites with 3¿wt% HNTCA as well a delay in the onset degradation temperature, thus leading to a broader processing window which enhances PHB processing by conventional techniques., This work was supported by the Ministry of Economy and Competitiveness (MINECO) [MAT2017-84909-C2-2-R]. D. Garcia-Garcia wants to thank the Spanish Ministry of Education, Culture and Sports for the financial support through a FPU grant [FPU13/06011].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of Maleinized Linseed Oil Loading as a Biobased Compatibilizer in Poly(Butylene Succinate) Composites with Almond Shell Flour

  • Limiñana-Gregori, Patricia
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] Green composites of poly(butylene succinate) (PBS) were manufactured with almond shell flour (ASF) by reactive compatibilization with maleinized linseed oil *MLO) by extrusion and subsequent injection molding. ASF was kept constant at 30 wt %, while the effect of different MLO loading on mechanical, thermal, thermomechanical, and morphology properties was studied. Uncompatibilized PBS/ASF composites show a remarkable decrease in mechanical properties due to the nonexistent polymer¿filler interaction, as evidenced by field emission scanning electron microscopy (FESEM). MLO provides a plasticization effect on PBS/ASF composites but, in addition, acts as a compatibilizer agent since the maleic anhydride groups contained in MLO are likely to react with hydroxyl groups in both PBS end chains and ASF particles. This compatibilizing effect is observed by FESEM with a reduction of the gap between the filler particles and the surrounding PBS matrix. In addition, the Tg of PBS increases from ¿28 °C to ¿12 °C with an MLO content of 10 wt %, thus indicating compatibilization. MLO has been validated as an environmentally friendly additive to PBS/ASF composites to give materials with high environmental efficiency., This work was supported by the Ministry of Economy and Competitiveness (MINECO) grant number MAT2017-84909-C2-2-R. L.Q.-C. wants to thank Generalitat Valenciana (GV) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

New Materials for 3D-Printing Based on Polycaprolactone with Gum Rosin and Beeswax as Additives

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Aldas-Carrasco, Miguel Fernando
[EN] In this work, different materials for three-dimensional (3D)-printing were studied, which based on polycaprolactone with two natural additives, gum rosin, and beeswax. During the 3D-printing process, the bed and extrusion temperatures of each formulation were established. After, the obtained materials were characterized by mechanical, thermal, and structural properties. The results showed that the formulation with containing polycaprolactone with a mixture of gum rosin and beeswax as additive behaved better during the 3D-printing process. Moreover, the miscibility and compatibility between the additives and the matrix were concluded through the thermal assessment. The mechanical characterization established that the addition of the mixture of gum rosin and beeswax provides greater tensile strength than those additives separately, facilitating 3D-printing. In contrast, the addition of beeswax increased the ductility of the material, which makes the 3D-printing processing difficult. Despite the fact that both natural additives had a plasticizing effect, the formulations containing gum rosin showed greater elongation at break. Finally, Fourier-Transform Infrared Spectroscopy assessment deduced that polycaprolactone interacts with the functional groups of the additives., This research was supported by the Spanish State Agency of Research trough the project MAT2017-84909-C2-2-R and Universidad Politecnica de Valencia-GVA through the project "Development".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Valorization of Linen Processing By-Products for the Development of Injection-Molded Green Composite Pieces of Polylactide with Improved Performance

  • Agüero, Ángel
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] This work reports the development and characterization of green composites based on polylactide (PLA) containing fillers and additives obtained from by-products or waste-streams from the linen processing industry. Flaxseed flour (FSF) was first produced by the mechanical milling of golden flaxseeds. The resultant FSF particles were melt-compounded at 30 wt% with PLA in a twin-screw extruder. Two multi-functionalized oils derived from linseed, namely epoxidized linseed oil (ELO) and maleinized linseed oil (MLO), were also incorporated during melt mixing at 2.5 and 5 parts per hundred resin (phr) of composite. The melt-compounded pellets were thereafter shaped into pieces by injection molding and characterized. Results showed that the addition of both multi-functionalized linseed oils successfully increased ductility, toughness, and thermal stability of the green composite pieces whereas water diffusion was reduced. The improvement achieved was related to both a plasticizing effect and, more interestingly, an enhancement of the interfacial adhesion between the biopolymer and the lignocellulosic particles by the reactive vegetable oils. The most optimal performance was attained for the MLO-containing green composite pieces, even at the lowest content, which was ascribed to the higher solubility of MLO with the PLA matrix. Therefore, the present study demonstrates the potential use of by-products or waste from flax (Linum usitatissimum L.) to obtain renewable raw materials of suitable quality to develop green composites with high performance for market applications such as rigid food packaging and food-contact disposable articles in the frame of the Circular Economy and Bioeconomy., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A comparative study on the reactive compatibilization of melt-processed polyamide 1010/polylactide blends by multi-functionalized additives derived from linseed oil and petroleum

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Rallini, M.
  • Dominici, F.
  • Torre, L.
[EN] This research work describes the manufacturing and characterization of novel engineering materials consisted of fully bio-based blends of polyamide 1010 (PA1010) with 20 wt% of polylactide (PLA). Four different compatibilizers were used to enhance the miscibility and the performance of the biopolymer blends. Two multi-functionalized vegetable oils (maleinized linseed oil (MLO) and epoxidized linseed oil (ELO)) and two petroleum-derived glycidyl-based additives (epoxy styrene-acrylic oligomer (ESAO) and styrene-glycidyl methacrylate copolymer (PS-GMA)) were tested during melt compounding. The resultant biopolymer blends were processed by either cast film extrusion or injection molding to obtain films and pieces, respectively. Thin films with an average thickness of 50¿60 µm and thick pieces of 4 mm were obtained, and their mechanical, morphological, thermal, thermomechanical, barrier and, optical properties were characterized. Although all four compatibilizers successfully provided compatibilization to the blends, the chemically modified vegetable oils, that is, MLO and ELO yielded the injection-molded pieces with the most balanced mechanical properties in terms of strength and toughness. Besides, the resultant films showed very low oxygen transmission rate values, thus broadening the potential of these biopolymer blends for the food packaging industry, This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. Quiles-Carrillo and Torres-Giner are recipients of a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) and a Juan de la Cierva contract (IJCI-2016-29675) from MICIU, respectively. Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images. Authors thank Polyscope for kindly supplying XibondTM 920 for this study.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Kinetic Analysis of the Curing of a Partially Biobased Epoxy Resin Using Dynamic Differential Scanning Calorimetry

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
[EN] This research presents a cure kinetics study of an epoxy system consisting of a partially bio-sourced resin based on diglycidyl ether of bisphenol A (DGEBA) with amine hardener and a biobased reactive diluent from plants representing 31 wt %. The kinetic study has been carried out using differential scanning calorimetry (DSC) under non-isothermal conditions at different heating rates. Integral and derivative isoconversional methods or model free kinetics (MFK) have been applied to the experimental data in order to evaluate the apparent activation energy, Ea, followed by the application of the appropriate reaction model. The bio-sourced system showed activation energy that is independent of the extent of conversion, with Ea values between 57 and 62 kJ·mol¿1, corresponding to typical activation energies of conventional epoxy resins. The reaction model was studied by comparing the calculated y(¿) and z(¿) functions with standard master plot curves. A two-parameter autocatalytic kinetic model of Šesták¿Berggren [SB(m,n)] was assessed as the most suitable reaction model to describe the curing kinetics of the epoxy resins studied since it showed an excellent agreement with the experimental data., This research was supported by the Spanish Ministry of Economy and Competitiveness (MINECO) program number MAT2017-84909-C2-2-R. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and the MECD for his FPU grant (FPU15/03812).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development and Characterization of Sustainable Composites from Bacterial Polyester Poly(3-Hydroxybutyrate-co-3-hydroxyhexanoate) and Almond Shell Flour by Reactive Extrusion with Oligomers of Lactic Acid

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Manuel-Mañogil, Jose
[EN] Eco-effcient Wood Plastic Composites (WPCs) have been obtained using poly(hydroxybutyrate-co-hexanoate) (PHBH) as the polymer matrix, and almond shell flour (ASF), a by-product from the agro-food industry, as filler/reinforcement. These WPCs were prepared with different amounts of lignocellulosic fillers (wt %), namely 10, 20 and 30. The mechanical characterization of these WPCs showed an important increase in their stiffness with increasing the wt % ASF content. In addition, lower tensile strength and impact strength were obtained. The field emission scanning electron microscopy (FESEM) study revealed the lack of continuity and poor adhesion among the PHBH-ASF interface. Even with the only addition of 10 wt % ASF, these green composites become highly brittle. Nevertheless, for real applications, the WPC with 30 wt % ASF is the most attracting material since it contributes to lowering the overall cost of the WPC and can be manufactured by injection moulding, but its properties are really compromised due to the lack of compatibility between the hydrophobic PHBH matrix and the hydrophilic lignocellulosic filler. To minimize this phenomenon, 10 and 20 phr (weight parts of OLA-Oligomeric Lactic Acid per one hundred weight parts of PHBH) were added to PHBH/ASF (30 wt % ASF) composites. Differential scanning calorimetry (DSC) suggested poor plasticization effect of OLA on PHBH-ASF composites. Nevertheless, the most important property OLA can provide to PHBH/ASF composites is somewhat compatibilization since some mechanical ductile properties are improved with OLA addition. The study by thermomechanical analysis (TMA), confirmed the increase of the coeffcient of linear thermal expansion (CLTE) with increasing OLA content. The dynamic mechanical characterization (DTMA), revealed higher storage modulus, E¿, with increasing ASF. Moreover, DTMA results confirmed poor plasticization of OLA on PHBH-ASF (30 wt % ASF) composites, but interesting compatibilization effects., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. This work was supported by the POLISABIO program grant number (2019-A02). J. Ivorra-Martinez is the recipient of an FPI grant from Universitat Politècnica de València (PAID-2019). L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bioactive Multilayer Polylactide Films with Controlled Release Capacity of Gallic Acid Accomplished by Incorporating Electrospun Nanostructured Coatings and Interlayers

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Montanes, Nestor|||0000-0001-6070-127X
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Lagaron, Jose M.
[EN] The present research reports on the development of bi- and multilayer polylactide (PLA) films by the incorporation of electrospun nanostructured PLA coatings and interlayers containing the antioxidant gallic acid (GA) at 40 wt% onto cast-extruded PLA films. To achieve the bilayer structures, submicron GA-loaded PLA fibers were applied on 200-µm cast PLA films in the form of coatings by electrospinning for 1, 2, and 3 h. For the multilayers, the cast PLA films were first coated on one side by electrospinning, then sandwiched with 10-µm PLA film on the other side, and the resultant whole structure was finally thermally post-treated at 150 ºC without pressure. Whereas the bilayer PLA films easily delaminated and lacked transparency, the multilayers showed sufficient adhesion between layers and high transparency for deposition times during electrospinning of up to 2 h. The incorporation of GA positively contributed to delaying the thermal degradation of PLA for approximately 10 ºC, as all films were thermally stable up to 345 ºC. The in vitro release studies performed in saline medium indicated that the GA released from the bilayer PLA films rapidly increased during the first 5 h of immersion while it stabilized after 45¿250 h. Interestingly, the PLA multilayers offered a high sustained release of GA, having the capacity to deliver the bioactive for over 1000 h. In addition, in the whole tested period, the GA released from the PLA films retained most of its antioxidant functionality. Thus, during the first days, the bilayer PLA films can perform as potent vehicles to deliver GA while the multilayer PLA films are able to show a sustained release of the natural antioxidant for extended periods, This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) program numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R and by the EU H2020 project YPACK (reference number 773872).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improvement of Impact Strength of Polylactide Blends with a Thermoplastic Elastomer Compatibilized with Biobased Maleinized Linseed Oil for Applications in Rigid Packaging

  • Tejada-Oliveros, Ramón
  • Balart, Rafael|||0000-0001-5670-7126
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Montanes, Nestor|||0000-0001-6070-127X
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] This research work reports the potential of maleinized linseed oil (MLO) as biobased compatibilizer in polylactide (PLA) and a thermoplastic elastomer, namely, polystyrene¿b¿(ethylene¿ran¿butylene)¿b¿styrene (SEBS) blends (PLA/SEBS), with improved impact strength for the packaging industry. The effects of MLO are compared with a conventional polystyrene¿b¿poly(ethylene¿ran¿butylene)¿b¿polystyrene¿graft¿maleic anhydride terpolymer (SEBS¿g¿MA) since it is widely used in these blends. Uncompatibilized and compatibilized PLA/SEBS blends can be manufactured by extrusion and then shaped into standard samples for further characterization by mechanical, thermal, morphological, dynamical¿mechanical, wetting and colour standard tests. The obtained results indicate that the uncompatibilized PLA/SEBS blend containing 20 wt.% SEBS gives improved toughness (4.8 kJ/m2) compared to neat PLA (1.3 kJ/m2). Nevertheless, the same blend compatibilized with MLO leads to an increase in impact strength up to 6.1 kJ/m2, thus giving evidence of the potential of MLO to compete with other petroleum¿ derived compatibilizers to obtain tough PLA formulations. MLO also provides increased ductile properties, since neat PLA is a brittle polymer with an elongation at break of 7.4%, while its blend with 20 wt.% SEBS and MLO as compatibilizer offers an elongation at break of 50.2%, much higher than that provided by typical SEBS¿g¿MA compatibilizer (10.1%). MLO provides a slight decrease (about 3 °C lower) in the glass transition temperature (Tg) of the PLA¿rich phase, thus showing some plasticization effects. Although MLO addition leads to some yellowing due to its intrinsic yellow colour, this can contribute to serving as a UV light barrier with interesting applications in the packaging industry. Therefore, MLO represents a cost¿effective and sustainable solution to the use of conventional petroleum¿derived compatibilizers., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Injection-Molded Parts of Partially Biobased Polyamide 610 and Biobased Halloysite Nanotubes

  • Marset, David
  • Dolza, Celia
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
  • Balart, Rafael|||0000-0001-5670-7126
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
[EN] This works focuses on the development of environmentally friendly composites with a partially biobased polyamide 610 (PA610), containing 63% biobased content, and a natural inorganic filler at the nanoscale, namely, halloysite nanotubes (HNTs). PA610 composites containing 10, 20, and 30 wt% HNTs were obtained by melt extrusion in a twin screw co-rotating extruder. The resulting composites were injection-molded for further characterization. The obtained materials were characterized to obtain reliable data about their mechanical, thermal, and morphological properties. The effect of the HNTs wt% on these properties was evaluated. From a mechanical standpoint, the addition of 30 wt% HNTs gave an increase in tensile modulus of twice the initial value, thus verifying how this type of natural load provides increased stiffness on injection molded parts. The materials prepared with HNTs slightly improved the thermal stability, while a noticeable improvement on thermomechanical resistance over a wide temperature range was observed with increasing HNTs content. The obtained results indicate that high biobased content composites can be obtained with an engineering thermoplastic, i.e., PA610, and a natural inorganic nanotubeshaped filler, i.e., HNTs, with balanced mechanical properties and attractive behavior against high temperature., This research was funded by the Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancing the Thermal Stability of Polypropylene by Blending with Low Amounts of Natural Antioxidants

  • Hernández-Fernández, Joaquín
  • Arrieta, Marina Patricia
  • E. Rayón|||0000-0002-0653-2046
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Natural antioxidants are added in very low amounts to protect a polypropylene (PP) matrix against thermo-oxidative degradation during processing. Thus, PP is melt-blended with caffeic, chlorogenic, trans-ferrulic, and p-coumaric acids, and also with flavone and 3-hydroxyflavone at 0.1 wt% with respect to the PP matrix. Neat PP and PP blended with three traditional antioxidants are prepared for comparison. A complete structural, thermal, and mechanical characterization is conducted. Ferrulic acid and particularly caffeic acid increases the thermal stability, showing also the highest activation energy. The structural changes of PP-based films due to the polymer thermal degradation at high temperature (i.e., 400 degrees C) followed by FTIR reveal that antioxidants effectively delay the thermal degradation process. The wettability and the mechanical performance are also studied to get information regarding the industrial application of such films. While caffeic acid provides a more flexible material, ferrulic acid provides higher water resistance. Finally, AFM-QNM shows that PP with caffeic acid has the highest miscibility., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO), PROMADEPCOL (MAT2017-84909-C2-2-R). M.P.A. thanks MINECO for Juan de la Cierva-incorporación postdoctoral contract (FJCI-2017-33536).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Development of Injection-Molded Polylactide Pieces with High Toughness by the Addition of Lactic Acid Oligomer and Characterization of Their Shape Memory Behavior

  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Moraga, Giovanni
  • Rojas-Lema, Sandra Paola
[EN] This work reports the effect of the addition of an oligomer of lactic acid (OLA), in the 5-20 wt% range, on the processing and properties of polylactide (PLA) pieces prepared by injection molding. The obtained results suggested that the here-tested OLA mainly performs as an impact modifier for PLA, showing a percentage increase in the impact strength of approximately 171% for the injection-molded pieces containing 15 wt% OLA. A slight plasticization was observed by the decrease of the glass transition temperature (T-g) of PLA of up to 12.5 degrees C. The OLA addition also promoted a reduction of the cold crystallization temperature (T-cc) of more than 10 degrees C due to an increased motion of the biopolymer chains and the potential nucleating effect of the short oligomer chains. Moreover, the shape memory behavior of the PLA samples was characterized by flexural tests with different deformation angles, that is, 15 degrees, 30 degrees, 60 degrees, and 90 degrees. The obtained results confirmed the extraordinary effect of OLA on the shape memory recovery (R-r) of PLA, which increased linearly as the OLA loading increased. In particular, the OLA-containing PLA samples were able to successfully recover over 95% of their original shape for low deformation angles, while they still reached nearly 70% of recovery for the highest angles. Therefore, the present OLA can be successfully used as a novel additive to improve the toughness and shape memory behavior of compostable packaging articles based on PLA in the new frame of the Circular Economy., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. L.Q.-C. wants to thank Generalitat Valenciana (GVA) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). D.L. thanks Universitat Politècnica de València (UPV) for the grant received through the PAID-01-18 program. S.T.-G. is recipient of a Juan de la Cierva contract (IJCI-2016-29675) from MICIU. S.R.-L. is recipient of a Santiago Grisolía contract (GRISOLIAP/2019/132) from GVA. J.I.-M. wants to thank UPV for an FPI grant PAID-01-19 (SP2019001). Microscopy services of UPV are acknowledged for their help in collecting and analyzing the microscopy images. Authors also thank Condensia Química S.A. for kindly supplying Glyoplast OLA 2.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Films Based on Thermoplastic Starch Blended with Pine Resin Derivatives for Food Packaging

  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Aldás-Carrasco, Miguel Fernando
  • Hernández-Fernández, Joaquín
  • Arrieta, Marina Patricia
[EN] Completely biobased and biodegradable thermoplastic starch (TPS) based materials with a tunable performance were prepared for food packaging applications. Five blends were prepared by blending TPS with 10 wt%. of different pine resins derivatives: gum rosin (GR), disproportionated gum rosin (RD), maleic anhydride-modified gum rosin (CM), pentaerythritol ester of gum rosin (LF), and glycerol ester of gum rosin (UG). The materials were characterized in terms of thermo-mechanical behavior, surface wettability, color performance, water absorption, X-ray diffraction pattern, and disintegration under composting conditions. It was determined that pine resin derivatives increase the hydrophobicity of TPS and also increase the elastic component of TPS which stiffen the TPS structure. The water uptake study revealed that GR and LF were able to decrease the water absorption of TPS, while the rest of the resins kept the water uptake ability. X-ray diffraction analyses revealed that GR, CM, and RD restrain the aging of TPS after 24 months of aging. Finally, all TPS-resin blends were disintegrated under composting conditions during the thermophilic incubation period (90 days). Because of the TPS-resin blend's performance, the prepared materials are suitable for biodegradable rigid food packaging applications., This research was funded by MINECO, with the project: PROMADEPCOL: MAT2017-84909-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Injection-molded parts of fully bio-based polyamide 1010 strengthened with waste derived slate fibers pretreated with glycidyl- and amino-silane coupling agents

  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Montanes, Nestor|||0000-0001-6070-127X
  • Balart, Rafael|||0000-0001-5670-7126
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Fully bio-based polyamide 1010 (PA1010) was melt-compounded with 15 wt% of slate fibers (SFs), which were obtained from wastes of the tile industry, and the resultant composites were shaped into parts by injection molding. The as-received fibers were first thermally treated and afterwards subjected to surface modification with glycidyl- and amino-silane coupling agents to improve the interfacial adhesion of the composites. The incorporation of both the glycidyl-silane slate fiber (G-SF) and amino-silane slate fiber (A-SF) remarkably improved the mechanical strength of PA1010, inducing a 3-fold increase in tensile modulus. The composite parts prepared with the silanized SFs also presented higher thermal stability and improved thermomechanical resistance. Water uptake was reduced below 1%, encouragingly suggesting that the mechanical performance of the PA1010/SF composites would be scarcely affected by atmospheric humidity. G-SF was the most effective in strengthening PA1010. This improvement was ascribed to the higher reactivity of the cyclic anhydride in the coupled silane with the terminal hydroxyl groups of the biopolymer., The Spanish Ministry of Science, Innovation and Universities MICIU) is acknowledged for funding through the MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R projects. Quiles-Carrillo holds a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) whereas Torres-Giner is a recipient of a Juan de la Cierva-Incorporacion contract (IJCI-2016-29675) from MICIU.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ductility and Toughness Improvement of Injection-Molded Compostable Pieces of Polylactide by Melt Blending with Poly(ε-caprolactone) and Thermoplastic Starch

  • Quiles-Carrillo, Luis
  • Montanes, Néstor
  • Pineiro, Fede
  • Jorda-Vilaplana, Amparo
  • Torres-Giner, Sergio
The present study describes the preparation and characterization of binary and ternary blends based on polylactide (PLA) with poly(ε-caprolactone) (PCL) and thermoplastic starch (TPS) to develop fully compostable plastics with improved ductility and toughness. To this end, PLA was first melt-mixed in a co-rotating twin-screw extruder with up to 40 wt % of different PCL and TPS combinations and then shaped into pieces by injection molding. The mechanical, thermal, and thermomechanical properties of the resultant binary and ternary blend pieces were analyzed and related to their composition. Although the biopolymer blends were immiscible, the addition of both PCL and TPS remarkably increased the flexibility and impact strength of PLA while it slightly reduced its mechanical strength. The most balanced mechanical performance was achieved for the ternary blend pieces that combined high PCL contents with low amounts of TPS, suggesting a main phase change from PLA/TPS (comparatively rigid) to PLA/PCL (comparatively flexible). The PLA-based blends presented an “island-and-sea” morphology in which the TPS phase contributed to the fine dispersion of PCL as micro-sized spherical domains that acted as a rubber-like phase with the capacity to improve toughness. In addition, the here-prepared ternary blend pieces presented slightly higher thermal stability and lower thermomechanical stiffness than the neat PLA pieces. Finally, all biopolymer pieces fully disintegrated in a controlled compost soil after 28 days. Therefore, the inherently low ductility and toughness of PLA can be successfully improved by melt blending with PCL and TPS, resulting in compostable plastic materials with a great potential in, for instance, rigid packaging applications., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) program numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R, and by the EU H2020 project YPACK (reference number 773872). L.Q.-C. wants to thank Generalitat Valenciana (GV) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. also acknowledges the MICIU for his Juan de la Cierva contract (IJCI-2016-29675)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Sustainable and Cost-Competitive Injection-Molded Pieces of Partially Bio-Based Polyethylene Terephthalate through the Valorization of Cotton Textile Waste

  • Montava-Jordà, Sergi
  • Torres-Giner, Sergio
  • Ferrándiz-Bou, Santiago
  • Quiles-Carrillo, Luis
  • Montanes, Néstor
This study presents the valorization of cotton waste from the textile industry for the development of sustainable and cost-competitive biopolymer composites. The as-received linter of recycled cotton was first chopped to obtain short fibers, called recycled cotton fibers (RCFs), which were thereafter melt-compounded in a twin-screw extruder with partially bio-based polyethylene terephthalate (bio-PET) and shaped into pieces by injection molding. It was observed that the incorporation of RCF, in the 1–10 wt% range, successfully increased rigidity and hardness of bio-PET. However, particularly at the highest fiber contents, the ductility and toughness of the pieces were considerably impaired due to the poor interfacial adhesion of the fibers to the biopolyester matrix. Interestingly, RCF acted as an effective nucleating agent for the bio-PET crystallization and it also increased thermal resistance. In addition, the overall dimensional stability of the pieces was improved as a function of the fiber loading. Therefore, bio-PET pieces containing 3–5 wt% RCF presented very balanced properties in terms of mechanical strength, toughness, and thermal resistance. The resultant biopolymer composite pieces can be of interest in rigid food packaging and related applications, contributing positively to the optimization of the integrated biorefinery system design and also to the valorization of textile wastes., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) through the AGL2015-63855-C2-1-R and MAT2017-84909-C2-2-R program numbers, We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced interfacial adhesion of polylactide/poly(ε-caprolactone)/walnut shell flour composites by reactive extrusion with maleinized linseed oil

  • Montava-Jordà, Sergi
  • Quiles-Carrillo, Luis
  • Richart, Nuria
  • Torres Giner, Sergio
  • Montanes, Néstor
Novel green composites were prepared by melt compounding a binary blend of polylactide (PLA) and poly(ε-caprolactone) (PCL) at 4/1 (wt/wt) with particles of walnut shell flour (WSF) in the 10–40 wt % range, which were obtained as a waste from the agro-food industry. Maleinized linseed oil (MLO) was added at 5 parts per hundred resin (phr) of composite to counteract the intrinsically low compatibility between the biopolymer blend matrix and the lignocellulosic fillers. Although the incorporation of WSF tended to reduce the mechanical strength and thermal stability of PLA/PCL, the MLO-containing composites filled with up to 20 wt % WSF showed superior ductility and a more balanced thermomechanical response. The morphological analysis revealed that the performance improvement attained was related to a plasticization phenomenon of the biopolymer blend and, more interestingly, to an enhancement of the interfacial adhesion of the green composites achieved by extrusion with the multi-functionalized vegetable oil., This research was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers AGL2015-63855-C2-1-R and MAT2017-84909-C2-2-R. L.Q.-C. holds a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) whereas S.T.-G. is a recipient of a Juan de la Cierva—Incorporación contract (IJCI-2016-29675) from MICIU., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimization of the curing and post-curing conditions for the manufacturing of partially bio-based epoxy resins with improved toughness

  • Lascano, Diego
  • Quiles-Carrillo, Luis
  • Torres-Giner, Sergio
  • Boronat, Teodomiro
  • Montanes, Néstor
© The Author(s)., This research deals with the influence of different curing and post-curing temperatures on the mechanical and thermomechanical properties as well as the gel time of an epoxy resin prepared by the reaction of diglycidyl ether of bisphenol A (DGEBA) with an amine hardener and a reactive diluent derived from plants at 31 wt %. The highest performance was obtained for the resins cured at moderate-to-high temperatures, that is, 80 ∘C and 90 ∘C , which additionally showed a significant reduction in the gel time. This effect was ascribed to the formation of a stronger polymer network by an extended cross-linking process of the polymer chains during the resin manufacturing. Furthermore, post-curing at either 125 ∘C or 150 ∘C yielded thermosets with higher mechanical strength and, more interestingly, improved toughness, particularly for the samples previously cured at moderate temperatures. In particular, the partially bio-based epoxy resin cured at 80 ∘C and post-cured at 150 ∘C for 1 h and 30 min, respectively, showed the most balanced performance due to the formation of a more homogeneous cross-linked structure., This research was supported by the Spanish Ministry of Science, Innovation, and Universities (MICIU) through the MAT2017-84909-C2-2-R program number., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding

  • Agüero, Ángel
  • Morcillo, Maria del Carmen
  • Quiles-Carrillo, Luis
  • Balart, Rafael
  • Boronat, Teodomiro
  • Lascano, Diego
  • Torres Giner, Sergio
  • Fenollar, Octavio
© 2019 by the authors., This research work aims to study the influence of the reprocessing cycles on the mechanical, thermal, and thermomechanical properties of polylactide (PLA). To this end, PLA was subjected to as many as six extrusion cycles and the resultant pellets were shaped into pieces by injection molding. Mechanical characterization revealed that the PLA pieces presented relatively similar properties up to the third reprocessing cycle, whereas further cycles induced an intense reduction in ductility and toughness. The effect of the reprocessing cycles was also studied by the changes in the melt fluidity, which showed a significant increase after four reprocessing cycles. An increase in the bio-polyester chain mobility was also attained with the number of the reprocessing cycles that subsequently favored an increase in crystallinity of PLA. A visual inspection indicated that PLA developed certain yellowing and the pieces also became less transparent with the increasing number of reprocessing cycles. Therefore, the obtained results showed that PLA suffers a slight degradation after one or two reprocessing cycles whereas performance impairment becomes more evident above the fourth reprocessing cycle. This finding suggests that the mechanical recycling of PLA for up to three cycles of extrusion and subsequent injection molding is technically feasible., This research was funded by by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Injection-Molded Polylactide Pieces with High Toughness by the Addition of Lactic Acid Oligomer and Characterization of Their Shape Memory Behavior

  • Lascano, Diego
  • Moraga, Giovanni
  • Ivorra-Martinez, Juan
  • Rojas-Lema, Sandra
  • Torres Giner, Sergio
  • Balart, Rafael
  • Boronat, Teodomiro
  • Quiles-Carrillo, Luis
© 2019 by the authors., This work reports the effect of the addition of an oligomer of lactic acid (OLA), in the 5–20 wt% range, on the processing and properties of polylactide (PLA) pieces prepared by injection molding. The obtained results suggested that the here-tested OLA mainly performs as an impact modifier for PLA, showing a percentage increase in the impact strength of approximately 171% for the injection-molded pieces containing 15 wt% OLA. A slight plasticization was observed by the decrease of the glass transition temperature (Tg) of PLA of up to 12.5 °C. The OLA addition also promoted a reduction of the cold crystallization temperature (Tcc) of more than 10 °C due to an increased motion of the biopolymer chains and the potential nucleating effect of the short oligomer chains. Moreover, the shape memory behavior of the PLA samples was characterized by flexural tests with different deformation angles, that is, 15°, 30°, 60°, and 90°. The obtained results confirmed the extraordinary effect of OLA on the shape memory recovery (Rr) of PLA, which increased linearly as the OLA loading increased. In particular, the OLA-containing PLA samples were able to successfully recover over 95% of their original shape for low deformation angles, while they still reached nearly 70% of recovery for the highest angles. Therefore, the present OLA can be successfully used as a novel additive to improve the toughness and shape memory behavior of compostable packaging articles based on PLA in the new frame of the Circular Economy., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bioactive Multilayer Polylactide Films with Controlled Release Capacity of Gallic Acid Accomplished by Incorporating Electrospun Nanostructured Coatings and Interlayers

  • Quiles Carrillo, Luis
  • Montanes, Néstor
  • Lagarón Cabello, José María
  • Balart, Rafael
  • Torres Giner, Sergio
The present research reports on the development of bi- and multilayer polylactide (PLA) films by the incorporation of electrospun nanostructured PLA coatings and interlayers containing the antioxidant gallic acid (GA) at 40 wt% onto cast-extruded PLA films. To achieve the bilayer structures, submicron GA-loaded PLA fibers were applied on 200-µm cast PLA films in the form of coatings by electrospinning for 1, 2, and 3 h. For the multilayers, the cast PLA films were first coated on one side by electrospinning, then sandwiched with 10-µm PLA film on the other side, and the resultant whole structure was finally thermally post-treated at 150 °C without pressure. Whereas the bilayer PLA films easily delaminated and lacked transparency, the multilayers showed sufficient adhesion between layers and high transparency for deposition times during electrospinning of up to 2 h. The incorporation of GA positively contributed to delaying the thermal degradation of PLA for approximately 10 °C, as all films were thermally stable up to 345 °C. The in vitro release studies performed in saline medium indicated that the GA released from the bilayer PLA films rapidly increased during the first 5 h of immersion while it stabilized after 45–250 h. Interestingly, the PLA multilayers offered a high sustained release of GA, having the capacity to deliver the bioactive for over 1000 h. In addition, in the whole tested period, the GA released from the PLA films retained most of its antioxidant functionality. Thus, during the first days, the bilayer PLA films can perform as potent vehicles to deliver GA while the multilayer PLA films are able to show a sustained release of the natural antioxidant for extended periods., This research was supported by the Ministry of Science, Innovation, and Universities (MICIU) program numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R and by the EU H2020 project YPACK (reference number 773872).L.Q.-C. wants to thank Generalitat Valenciana (GV) for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. acknowledges MICIU for his Juan de la Cierva–Incorporación contract (IJCI-2016-29675)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

On the Use of Gallic Acid as a Potential Natural Antioxidant and Ultraviolet Light Stabilizer in Cast-Extruded Bio-Based High-Density Polyethylene Films

  • Quiles Carrillo, Luis
  • Montava-Jordà, Sergi
  • Boronat, Teodomiro
  • Sammon, Chris
  • Torres Giner, Sergio
This study originally explores the use of gallic acid (GA) as a natural additive in bio-based high-density polyethylene (bio-HDPE) formulations. Thus, bio-HDPE was first melt-compounded with two different loadings of GA, namely 0.3 and 0.8 parts per hundred resin (phr) of biopolymer, by twin-screw extrusion and thereafter shaped into films using a cast-roll machine. The resultant bio-HDPE films containing GA were characterized in terms of their mechanical, morphological, and thermal performance as well as ultraviolet (UV) light stability to evaluate their potential application in food packaging. The incorporation of 0.3 and 0.8 phr of GA reduced the mechanical ductility and crystallinity of bio-HDPE, but it positively contributed to delaying the onset oxidation temperature (OOT) by 36.5 °C and nearly 44 °C, respectively. Moreover, the oxidation induction time (OIT) of bio-HDPE, measured at 210 °C, was delayed for up to approximately 56 and 240 min, respectively. Furthermore, the UV light stability of the bio-HDPE films was remarkably improved, remaining stable for an exposure time of 10 h even at the lowest GA content. The addition of the natural antioxidant slightly induced a yellow color in the bio-HDPE films and it also reduced their transparency, although a high contact transparency level was maintained. This property can be desirable in some packaging materials for light protection, especially UV radiation, which causes lipid oxidation in food products. Therefore, GA can successfully improve the thermal resistance and UV light stability of green polyolefins and will potentially promote the use of natural additives for sustainable food packaging applications., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evaluation of Different Compatibilization Strategies to Improve the Performance of Injection-Molded Green Composite Pieces Made of Polylactide Reinforced with Short Flaxseed Fibers

  • Agüero, Ángel
  • Garcia-Sanoguera, David
  • Lascano, Diego
  • Rojas-Lema, Sandra
  • Ivorra-Martinez, Juan
  • Fenollar, Octavio
  • Torres-Giner, Sergio
© 2020 by the authors., Green composites made of polylactide (PLA) and short flaxseed fibers (FFs) at 20 wt % were successfully compounded by twin-screw extrusion (TSE) and subsequently shaped into pieces by injection molding. The linen waste derived FFs were subjected to an alkalization pretreatment to remove impurities, improve the fiber surface quality, and make the fibers more hydrophobic. The alkali-pretreated FFs successfully reinforced PLA, leading to green composite pieces with higher mechanical strength. However, the pieces also showed lower ductility and toughness and the lignocellulosic fibers easily detached during fracture due to the absence or low interfacial adhesion with the biopolyester matrix. Therefore, four different compatibilization strategies were carried out to enhance the fiber–matrix interfacial adhesion. These routes consisted on the silanization of the alkalized FFs with a glycidyl silane, namely (3-glycidyloxypropyl) trimethoxysilane (GPTMS), and the reactive extrusion (REX) with three compatibilizers, namely a multi-functional epoxy-based styrene-acrylic oligomer (ESAO), a random copolymer of poly(styrene-co-glycidyl methacrylate) (PS-co-GMA), and maleinized linseed oil (MLO). The results showed that all the here-tested compatibilizers improved mechanical strength, ductility, and toughness as well as the thermal stability and thermomechanical properties of the green composite pieces. The highest interfacial adhesion was observed in the green composite pieces containing the silanized fibers. Interestingly, PS-co-GMA and, more intensely, ESAO yielded the pieces with the highest mechanical performance due to the higher reactivity of these additives with both composite components and their chain-extension action, whereas MLO led to the most ductile pieces due to its secondary role as plasticizer for PLA., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tailoring the Properties of Thermo-Compressed Polylactide Films for Food Packaging Applications by Individual and Combined Additions of Lactic Acid Oligomer and Halloysite Nanotubes

  • Rojas-Lema, Sandra
  • Quiles Carrillo, Luis
  • Garcia-Garcia, Daniel
  • Meléndez-Rodríguez, Beatriz
  • Balart, Rafael
  • Torres Giner, Sergio
© 2020 by the authors, In this work, films of polylactide (PLA) prepared by extrusion and thermo-compression were plasticized with oligomer of lactic acid (OLA) at contents of 5, 10, and 20 wt%. The PLA sample containing 20 wt% of OLA was also reinforced with 3, 6, and 9 parts per hundred resin (phr) of halloysite nanotubes (HNTs) to increase the mechanical strength and thermal stability of the films. Prior to melt mixing, ultrasound-assisted dispersion of the nanoclays in OLA was carried out at 100 °C to promote the HNTs dispersion in PLA and the resultant films were characterized with the aim to ascertain their potential in food packaging. It was observed that either the individual addition of OLA or combined with 3 phr of HNTs did not significantly affect the optical properties of the PLA films, whereas higher nanoclay contents reduced lightness and induced certain green and blue tonalities. The addition of 20 wt% of OLA increased ductility of the PLA film by nearly 75% and also decreased the glass transition temperature (Tg) by over 18 °C. The incorporation of 3 phr of HNTs into the OLA-containing PLA films delayed thermal degradation by 7 °C and additionally reduced the permeabilities to water and limonene vapors by approximately 8% and 47%, respectively. Interestingly, the highest barrier performance was attained for the unfilled PLA film plasticized with 10 wt% of OLA, which was attributed to a crystallinity increase and an effect of “antiplasticization”. However, loadings of 6 and 9 phr of HNTs resulted in the formation of small aggregates that impaired the performance of the blend films. The here-attained results demonstrates that the properties of ternary systems of PLA/OLA/HNTs can be tuned when the plasticizer and nanofiller contents are carefully chosen and the resultant nanocomposite films can be proposed as a bio-sourced alternative for compostable packaging applications., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mechanical Recycling of Partially Bio-Based and Recycled Polyethylene Terephthalate Blends by Reactive Extrusion with Poly(styrene-co-glycidyl methacrylate)

  • Montava-Jordà, Sergi
  • Lascano, Diego
  • Quiles-Carrillo, Luis
  • Montanes, Néstor
  • Boronat, Teodomiro
  • Martínez-Sanz, Antonio V.
  • Ferrándiz-Bou, Santiago
  • Torres-Giner, Sergio
In the present study, partially bio-based polyethylene terephthalate (bio-PET) was melt-mixed at 15–45 wt% with recycled polyethylene terephthalate (r-PET) obtained from remnants of the injection blowing process of contaminant-free food-use bottles. The resultant compounded materials were thereafter shaped into pieces by injection molding for characterization. Poly(styrene-co-glycidyl methacrylate) (PS-co-GMA) was added at 1–5 parts per hundred resin (phr) of polyester blend during the extrusion process to counteract the ductility and toughness reduction that occurred in the bio-PET pieces after the incorporation of r-PET. This random copolymer effectively acted as a chain extender in the polyester blend, resulting in injection-molded pieces with slightly higher mechanical resistance properties and nearly the same ductility and toughness than those of neat bio-PET. In particular, for the polyester blend containing 45 wt% of r-PET, elongation at break (εb) increased from 10.8% to 378.8% after the addition of 5 phr of PS-co-GMA, while impact strength also improved from 1.84 kJ·m−2 to 2.52 kJ·m−2. The mechanical enhancement attained was related to the formation of branched and larger macromolecules by a mechanism of chain extension based on the reaction of the multiple glycidyl methacrylate (GMA) groups present in PS-co-GMA with the hydroxyl (–OH) and carboxyl (–COOH) terminal groups of both bio-PET and r-PET. Furthermore, all the polyester blend pieces showed thermal and dimensional stabilities similar to those of neat bio-PET, remaining stable up to more than 400 °C. Therefore, the use low contents of the tested multi-functional copolymer can successfully restore the properties of bio-based but non-biodegradable polyesters during melt reprocessing with their recycled petrochemical counterparts and an effective mechanical recycling is achieved., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of the Mechanical and Thermal Properties of Injection-Molded Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/Hydroxyapatite Nanoparticles Parts for Use in Bone Tissue Engineering

  • Ivorra-Martinez, Juan
  • Quiles-Carrillo, Luis
  • Boronat, Teodomiro
  • Torres-Giner, Sergio
  • Covas, José A.
© 2020 by the authors., In the present study, poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) [P(3HB-co-3HHx)] was reinforced with hydroxyapatite nanoparticles (nHA) to produce novel nanocomposites for potential uses in bone reconstruction. Contents of nHA in the 2.5–20 wt % range were incorporated into P(3HB-co-3HHx) by melt compounding and the resulting pellets were shaped into parts by injection molding. The addition of nHA improved the mechanical strength and the thermomechanical resistance of the microbial copolyester parts. In particular, the addition of 20 wt % of nHA increased the tensile (Et) and flexural (Ef) moduli by approximately 64% and 61%, respectively. At the highest contents, however, the nanoparticles tended to agglomerate, and the ductility, toughness, and thermal stability of the parts also declined. The P(3HB-co-3HHx) parts filled with nHA contents of up to 10 wt % matched more closely the mechanical properties of the native bone in terms of strength and ductility when compared with metal alloys and other biopolymers used in bone tissue engineering. This fact, in combination with their biocompatibility, enables the development of nanocomposite parts to be applied as low-stress implantable devices that can promote bone reconstruction and be reabsorbed into the human body., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R and the POLISABIO program with grant number 2019-A02., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A comparative study on the effect of different reactive compatibilizers on injection‐molded pieces of bio‐based high‐density polyethylene/polylactide blends

  • Quiles-Carrillo, L.
  • Montanes, N.
  • Jorda‐Vilaplana, A.
  • Balart, Rafael
  • Torres-Giner, S.
The present study reports on the development of binary blends consisting of bio‐based high‐density polyethylene (bio‐HDPE) with polylactide (PLA), in the 5–20 wt % range, prepared by melt compounding and then shaped into pieces by injection molding. In order to enhance the miscibility between the green polyolefin and the biopolyester, different reactive compatibilizers were added during the melt‐blending process, namely polyethylene‐grafted maleic anhydride (PE‐g‐MA), poly(ethylene‐co‐glycidyl methacrylate) (PE‐co‐GMA), maleinized linseed oil (MLO), and a combination of MLO with dicumyl peroxide (DCP). Among the tested compatibilizers, the dual addition of MLO and DCP provided the binary blend pieces with the most balanced mechanical performance in terms of rigidity and impact strength as well as the highest thermal stability. The fracture surface of the binary blend piece processed with MLO and DCP revealed the formation of a continuous structure in which the dispersed PLA phase was nearly no discerned in the bio‐HDPE matrix. The resultant miscibility improvement was ascribed to both the high solubility and plasticizing effect of MLO on the PLA phase as well as the crosslinking effect of DCP on both biopolymers. The latter effect was particularly related to the formation of macroradicals of each biopolymer that, thereafter, led to the in situ formation of bio‐HDPE‐co‐PLA copolymers and also to the development of a partially crosslinked network in the binary blend. As a result, cost‐effective and fully bio‐based polymer pieces with improved mechanical strength, high toughness, and enhanced thermal resistance were obtained., This research was funded by the EU H2020 project YPACK (reference number 773872) and by the Ministry of Science, Innovation, and Universities (MICIU, project numbers MAT2017‐84909‐C2‐2‐R and AGL2015‐63855‐C2‐1‐R). Quiles‐Carrillo and Torres‐Giner are recipients of a FPU grant (FPU15/03812) from the Spanish Ministry of Education, Culture, and Sports (MECD) and a Juan de la Cierva contract (IJCI‐2016‐29675) from the MICIU, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In situ compatibilization of biopolymer ternary blends by reactive extrusion with low-functionality epoxy-based styrene–acrylic oligomer

  • Quiles-Carrillo, L.
  • Montanes, N.
  • Lagarón Cabello, José María
  • Balart, Rafael
  • Torres-Giner, S.
The present study reports on the use of low-functionality epoxy-based styrene–acrylic oligomer (ESAO) to compatibilize immiscible ternary blends made of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), polylactide (PLA), and poly(butylene adipate-co-terephthalate) (PBAT). The addition during melt processing of low-functionality ESAO at two parts per hundred resin (phr) of biopolymer successfully changed the soften inclusion phase in the blend system to a thinner morphology, yielding biopolymer ternary blends with higher mechanical ductility and also improved oxygen barrier performance. The compatibilization achieved was ascribed to the in situ formation of a newly block terpolymer, i.e. PHBV-b-PLA-b-PBAT, which was produced at the blend interface by the reaction of the multiple epoxy groups present in ESAO with the functional terminal groups of the biopolymers. This chemical reaction was mainly linear due to the inherently low functionality of ESAO and the more favorable reactivity of the epoxy groups with the carboxyl groups of the biopolymers, which avoided the formation of highly branched and/or cross-linked structures and thus facilitated the films processability. Therefore, the reactive blending of biopolymers at different mixing ratios with low-functionality ESAO represents a straightforward methodology to prepare sustainable plastics at industrial scale with different physical properties that can be of interest in, for instance, food packaging applications., This research was funded by the EU H2020 project YPACK (Reference number 773872) and by the Spanish Ministry of Science, Innovation, and Universities (MICIU) with project numbers MAT2017-84909-C2-2-R and AGL2015-63855-C2-1-R. L. Quiles-Carrillo wants to thank the Spanish Ministry of Education, Culture, and Sports (MECD) for financial support through his FPU Grant Number FPU15/03812. Torres-Giner also acknowledges the MICIU for his Juan de la Cierva contract (IJCI-2016-29675)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microencapsulation of Copper(II) Sulfate in Ionically Cross-Linked Chitosan by Spray Drying for the Development of Irreversible Moisture Indicators in Paper Packaging

  • Rojas-Lema, Sandra
  • Terol, Jorge
  • Fages, Eduardo
  • Balart, Rafael
  • Quiles-Carrillo, Luis
  • Prieto López, Cristina
  • Torres Giner, Sergio
© 2020 by the authors, Copper(II) sulfate-loaded chitosan microparticles were herein prepared using ionic cross-linking with sodium tripolyphosphate (STPP) followed by spray drying. The microencapsulation process was optimal using an inlet temperature of 180 °C, a liquid flow-rate of 290 mL/h, an aspiration rate of 90%, and an atomizing gas flow-rate of 667 nL/h. Chitosan particles containing copper(II) sulfate of approximately 4 µm with a shrunken-type morphology were efficiently attained and, thereafter, fixated on a paper substrate either via cross-linking with STPP or using a chitosan hydrogel. The latter method led to the most promising system since it was performed at milder conditions and the original paper quality was preserved. The developed cellulose substrates were reduced and then exposed to different humidity conditions and characterized using colorimetric measurements in order to ascertain their potential as irreversible indicators for moisture detection. The results showed that the papers coated with the copper(II) sulfate-containing chitosan microparticles were successfully able to detect ambient moisture shown by the color changes of the coatings from dark brown to blue, which can be easily seen with the naked eye. Furthermore, the chitosan microparticles yielded no cytotoxicity in an in vitro cell culture experiment. Therefore, the cellulose substrates herein developed hold great promise in paper packaging as on-package colorimetric indicators for monitoring moisture in real time., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Torrefaction of Coffee Husk Flour for the Development of Injection-Molded Green Composite Pieces of Polylactide with High Sustainability

  • Ortiz-Barajas, Diana L.
  • Arévalo-Prada, Johan A.
  • Fenollar, Octavio
  • Rueda-Ordóñez, Yesid J.
  • Torres-Giner, Sergio
© 2020 by the authors., Coffee husk, a major lignocellulosic waste derived from the coffee industry, was first ground into flour of fine particles of approximately 90 µm and then torrefied at 250 °C to make it more thermally stable and compatible with biopolymers. The resultant torrefied coffee husk flour (TCHF) was thereafter melt-compounded with polylactide (PLA) in contents from 20 to 50 wt% and the extruded green composite pellets were shaped by injection molding into pieces and characterized. Although the incorporation of TCHF reduced the ductility and toughness of PLA, filler contents of 20 wt% successfully yielded pieces with balanced mechanical properties in both tensile and flexural conditions and improved hardness. Contents of up to 30 wt% of TCHF also induced a nucleating effect that favored the formation of crystals of PLA, whereas the thermal degradation of the biopolyester was delayed by more than 7 °C. Furthermore, the PLA/TCHF pieces showed higher thermomechanical resistance and their softening point increased up to nearly 60 °C. Therefore, highly sustainable pieces were developed through the valorization of large amounts of coffee waste subjected to torrefaction. In the Circular Bioeconomy framework, these novel green composites can be used in the design of compostable rigid packaging and food contact disposables., This research work was funded by the Spanish Ministry of Science and Innovation (MICI), project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R, and by the Industrial University of Santander., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Gum rosin as a size control agent of poly(Butylene adipate-co-terephthalate) (pbat) domains to increase the toughness of packaging formulations based on polylactic acid (pla)

  • Aldas, M.
  • Ferri, J. M.
  • Motoc, D. L.
  • Peponi, Laura
  • Arrieta, Marina P.
  • López-Martínez, J.
Gum rosin (GR) was used as a natural additive to improve the compatibility between polylactic acid, PLA, and poly(butylene adipate-co-terephthalate, PBAT, blended with 20 wt.% of PBAT (PLA/PBAT). The PBAT was used as a soft component to increase the ductility of PLA and its fracture toughness. The coalescence of the PBAT domains was possible due to the plasticization effect of the GR component. These domains contributed to increasing the toughness of the final material due to the variation and control of the PBAT domains’ size and consequently, reducing the stress concentration points. The GR was used in contents of 5, 10, 15, and 20 phr. Consequently, the flexural properties were improved and the impact resistance increased up to 80% in PLA/PBAT_15GR with respect to the PLA/PBAT formulation. Field emission scanning electron microscope (FESEM) images allowed observing that the size of PBAT domains of 2–3 µm was optimal to reduce the impact stress. Differential scanning calorimetry (DSC) analysis showed a reduction of up to 8C on the PLA melting temperature and up to 5.3C of the PLA glass transition temperature in the PLA/PBAT_20GR formulation, which indicates an improvement in the processability of PLA. Finally, transparent films with improved oxygen barrier performance and increased hydrophobicity were obtained suggesting the potential interest of these blends for the food packaging industry., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Valorization of linen processing by-products for the development of injection-molded green composite pieces of polylactide with improved performance

  • Agüero, Ángel
  • Lascano, Diego
  • Garcia-Sanoguera, David
  • Fenollar, Octavio
  • Torres Giner, Sergio
This work reports the development and characterization of green composites based on polylactide (PLA) containing fillers and additives obtained from by-products or waste-streams from the linen processing industry. Flaxseed flour (FSF) was first produced by the mechanical milling of golden flaxseeds. The resultant FSF particles were melt-compounded at 30 wt% with PLA in a twin-screw extruder. Two multi-functionalized oils derived from linseed, namely epoxidized linseed oil (ELO) and maleinized linseed oil (MLO), were also incorporated during melt mixing at 2.5 and 5 parts per hundred resin (phr) of composite. The melt-compounded pellets were thereafter shaped into pieces by injection molding and characterized. Results showed that the addition of both multi-functionalized linseed oils successfully increased ductility/ toughness, and thermal stability of the green composite pieces whereas water diffusion was reduced. The improvement achieved was related to both a plasticizing effect and, more interestingly, an enhancement of the interfacial adhesion between the biopolymer and the lignocellulosic particles by the reactive vegetable oils. The most optimal performance was attained for the MLO-containing green composite pieces, even at the lowest content, which was ascribed to the higher solubility of MLO with the PLA matrix. Therefore, the present study demonstrates the potential use of by-products or waste from flax (Linum usitatissimum L.) to obtain renewable raw materials of suitable quality to develop green composites with high performance for market applications such as rigid food packaging and food-contact disposable articles in the frame of the Circular Economy and Bioeconomy., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R., Peer reviewed