Pasar al contenido principal

DISEÑO INNOVADOR DE CELDAS ELECTROQUIMICAS REGENERATIVAS DE TEMPERATURA INTERMEDIA

RTI2018-095088-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Intermediate-Temperature Electrochemical Performance of Air Electrodes for Solid Oxide Cells with Spray-Pyrolyzed Active Layers

  • Zapata-Ramírez, Víctor
  • Dos Santos-Gómez, Lucía
  • Mather, Glenn C.
  • Marrero-López, David
  • Pérez-Coll, Domingo
The potential of interactive layers of mixed-conducting oxides for improving the performance of air electrodes of solid oxide cells in the intermediate-temperature range is demonstrated. Active layers of CeGdO (CGO), CePrO (CPO), and SrFeMoO (SFM) with thickness in the range 200-400 nm are deposited on CGO-based electrolyte by spray pyrolysis, followed by deposition of a SFM/CGO composite air electrode by painting. The morphologies and phase composition of the active layers are examined by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy microanalysis. The electrochemical performance of the electrolyte-electrode assemblies is determined by impedance spectroscopy in the range 600-800 °C. Significant improvements in the performance of the electrode process and the geometrically normalized ohmic conductance are observed for the assembly with a CPO active layer with mixed-oxide-ionic-electronic conductivity, especially in the low-temperature range, attributable to extension of the surface path of the electrochemical reactions. The CGO intermediate layer also improves performance but to a lesser degree, most likely due to better ionic-current collection in comparison to the assemblies with either SFM as the active layer or no active layer., We acknowledge the “Fundacioń Domingo Martínez” (Ayuda a la Investigación 2017. Área de Materiales: celdas decombustible) and “Ministerio de Ciencia, Innovación y Universidades” (RTI2018-095088-B-I00 and RTI2018-093735-B-I00) for financial support. Collaboration between the research groups was facilitated by the “Red de Excelencia”program (MINECO, MAT2017-090695-REDT).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Perspectives on Cathodes for Protonic Ceramic Fuel Cells

  • Mather, Glenn C.
  • Muñoz-Gil, Daniel
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Marrero-López, David
  • Pérez-Coll, Domingo
This article belongs to the Special Issue Recent Advances in Electrodes for Proton-Conducting Solid Oxide Fuel Cells., Protonic ceramic fuel cells (PCFCs) are promising electrochemical devices for the efficient and clean conversion of hydrogen and low hydrocarbons into electrical energy. Their intermediate operation temperature (500–800 °C) proffers advantages in terms of greater component compatibility, unnecessity of expensive noble metals for the electrocatalyst, and no dilution of the fuel electrode due to water formation. Nevertheless, the lower operating temperature, in comparison to classic solid oxide fuel cells, places significant demands on the cathode as the reaction kinetics are slower than those related to fuel oxidation in the anode or ion migration in the electrolyte. Cathode design and composition are therefore of crucial importance for the cell performance at low temperature. The different approaches that have been adopted for cathode materials research can be broadly classified into the categories of protonic–electronic conductors, oxide-ionic–electronic conductors, triple-conducting oxides, and composite electrodes composed of oxides from two of the other categories. Here, we review the relatively short history of PCFC cathode research, discussing trends, highlights, and recent progress. Current understanding of reaction mechanisms is also discussed., This work was funded by MICINN (Spain), grant numbers RTI2018-095088-B-I00 and RTI2018-093735-B-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

SrZr0.9Y0.1O3−δ thin films by in-situ synthesis of triple alkoxide for protonic ceramic electrolyser membranes

  • Triviño Peláez, Ángel
  • Mather, Glenn C.
  • Pérez-Coll, Domingo
  • Aparicio, Mario
  • Mosa Ruiz, Jadra
[EN] Synthesis of the proton-conducting electrolyte SrZrYO(SZY) was undertaken by the sol–gel method employing an all-alkoxide route from reaction of strontium alkoxide produced in-situ and commercial zirconium and yttrium alkoxides. The solution was homogenized by a previous ligand exchange in 2-methoxyethanol to control the polycondensation rate and achieve SZY at the low final firing temperature of 700–800 °C. SZY thin films (~270 nm) were assisted by dip-coating on different substrates and characterized by scanning and transmission electron microscopy, grazing X-ray diffraction and confocal micro-Raman spectroscopy, revealing well-crystallized SZY phase with orthorhombic symmetry (space group, Pnma). Impedance spectroscopy of a thin film deposited on a quartz substrate revealed that protons contribute to transport in wet conditions as confirmed by a lower conductivity in DO-humidified air (1.02 eV) compared to HO-wetted air (0.99 eV), with the difference in activation energy consistent with a conductive isotope effect. [Figure not available: see fulltext.]., Ministerio de Ciencia, Innovación y Universidades of Spain for financial support (project ENE2015-66183-R, MAT2017-90695-3295-REDT, RTI2018-095088-B-I00 and student grant FPI BES-2016-077023). We also thank D. Ruiz and Dr. A. del Campo for their assistance with the experimental techniques., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced proton conductivity and stability of Ba-deficient BaCe0.8Y0.2O3-δ

  • Triviño Peláez, Ángel
  • Pérez-Coll, Domingo
  • Mosa Ruiz, Jadra
  • Ritter, Clemens
  • Amador, Ulises
  • Mather, Glenn C.
[EN] A-cation deficiency has a significant impact on the properties of proton-conducting perovskites (ABO), depending on factors such as the ionic radius, concentration of dopant and degree of substoichiometry of the A-site cation. Here, we focus on the influence of Ba deficiency on the structure, stability and partial electrical conductivities of the perovskite BaCeYO (BCY20). Neutron powder diffraction is employed to determine a monoclinic symmetry (space group I2/m) for BaCeYO (B95CY20), with greater distortion and specific free volume than BCY20. Confocal Raman microscopy integrated with atomic force microscopy and X-ray diffraction confirm improved resistance to carbonate formation in the Ba-deficient material. Electrical conductivity is also greater for B95CY20 in both wet and dry oxidising and moderate reducing conditions, reaching ≈1.4 and 1 S m in dry conditions of O and N, respectively, at 600 °C. Partial conductivities determined by a defect-chemistry-based method indicate that proton conductivity is dominant in wet air for temperatures <700 °C and greater for B95CY20 (≈0.95 S m at 600 °C) in comparison to BCY20 (≈0.58 S m at 600 °C), with an associated hydration enthalpy of −128 kJ mol. Mixed oxide ionic-electronic conductivity dominates in dry oxidising conditions and, again, is greater for Ba substoichiometric material., We thank MICINN (Spain) for financial assistance through the predoctoral grant BES-2016-077023 and projects RTI2018-095088-B-I00, RTI2018-09573-J-I00 and MAT2017-90695-REDT. Access to the neutron facilities at the Institut Laue Langevin (Grenoble, France) is gratefully acknowledged (proposal EASY-459; DOI: 10.5291/ILL-DATA.EASY-459)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Processing and characterisation of BaZr0.8Y0.2O3- δ proton conductor densified at 1200 °c

  • Triviño Peláez, Ángel
  • Pérez-Coll, Domingo
  • Aparicio, Mario
  • Fagg, Duncan P.
  • Mosa Ruiz, Jadra
  • Mather, Glenn C.
[EN] Barium zirconate-based perovskites (BZY) are intensely studied proton conductors for high-temperature electrochemical applications; however, their refractory nature means excessive temperatures are required for sintering (∼1700 °C). Although different strategies have been employed to improve densification, a high-temperature step (1300-1700 °C) is generally required to achieve sufficient grain growth and good electrical properties. Here, sol-gel synthesis using alkoxide precursors is employed to obtain BaZr0.8Y0.2O3-δ sinter-reactive powders with Ba excess at 750 °C. High relative densities (∼98%) of ceramic bodies with an average grain size ∼190 nm were obtained on sintering isostatically-pressed pellets at the uniquely low temperature of 1200 °C for 4 hours on addition of 4% mol ZnO as a sintering agent to the Ba-excess sol-gel powders. Impedance spectroscopy indicates that the resistance of the greater grain-boundary volume arising from the low densification temperature is largely offset by a higher specific grain-boundary conductivity than that of the same composition sintered at 1650 °C with larger grain size. Conductivity measurements for prolonged periods in dry and wet (pH2O ∼ 0.022 atm) 90% N2 : 10% H2 and 90% Ar : 10% CO2 atmospheres at 500 °C verified that Ba excess in the starting composition did not contribute to deteriorating chemical stability. Processing of sol-gel BZY nanopowders with Ba excess combined with ZnO sintering aid is thus demonstrated as a successful low-temperature route for obtaining BZY with high density, stability and sufficient grain growth for electrochemical applications. This journal is, We thank MICINN in Spain for financial support through projects RTI2018-095088-B-I00, RTI2018-095373-J-100 and predoctoral grant BES-2016-077023. DPF also thanks the FCT (Fundação para a Ciência e a Tecnologia, grants numbers PTDC/QUI-ELT/3681/2020, POCI-01-0145-FEDER-032241, UIDB/00481/2020 and UIDP/00481/2020) and the Centro Portugal Regional Operational Programme (Centro2020), under the PORTUGAL 2020 Partnership Agreement, through the European Regional Development Fund (ERDF), grant number CENTRO-01-0145-FEDER-022083. We acknowledge support of the publication fee by the CSIC (Spain) Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimisation of high-performance, cobalt-free SrFe1-xMoxO3-δ cathodes for solid oxide fuel cells prepared by spray pyrolysis

  • Zapata-Ramírez, Víctor
  • Rosendo-Santos, Paula
  • Amador, Ulises
  • Mather, Glenn C.
  • Pérez-Coll, Domingo
[EN] Strontium-ferrite-based perovskites as cobalt-free cathodes for intermediate-temperature solid oxide fuel cells (IT-SOFCs) have been analysed employing structural, stability and electrochemical studies. Neutron diffraction of SrFeO and SrFeMoO prepared by a Pechini method confirmed that SrFeO undergoes a phase transition from tetragonal to cubic symmetry at 300–400 °C, whereas Mo-doping stabilises cubic symmetry in the range RT-900 °C. Spray-pyrolysed electrodes offered significantly lower area-specific resistances of 0.2 and 0.11 Ω cm for SrFeO and SrFeMoO at 700 °C, respectively, in comparison to their analogues synthesised by the Pechini method (0.55 and 0.42 Ω cm), and lower grain size, as confirmed by scanning electron microscopy. Thermal cycling and ageing studies indicated a more robust response for the spray-pyrolysed electrodes, in particular the Mo-doped phase, which achieved a stable electrode-polarisation resistance <0.1 Ω cm for 10 heating/cooling cycles and 100 h of ageing at 700 °C. Anode-supported single cells with a thin CeGdO electrolyte produced performances of 0.5 and 0.9 W cm at 700 and 800 °C, respectively. SrFeMoO deposited by spray pyrolysis is, thus, proposed as a promising cobalt-free cathode for IT-SOFC based on its good structural stability and highly competitive electrochemical performance., The authors acknowledge the Fundación Domingo Martínez (“Ayuda a la Investigación 2017. Área de Materiales: celdas de combustible”) and “Ministerio de Ciencia, Innovación y Universidades” (RTI2018-095088-B-I00) for financial support. We also thank the Spanish MICINN and the Agencia Estatal de Investigación (AEI)/Fondo Europeo de Desarrollo Regional (FEDER/UE) for funding the Project PID2019-106662RB-C41. UA and PRS thank University San Pablo CEU (USP CEU) for financial support. We thank Institut Laue-Langevin (ILL) for allocation of beam time (experiment code 5-21-1132 https://doi.org/10.5291/ILL-DATA. 5-21- 1132). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The effects of Sr content on the performance of Nd1- xSrxCoO3-δair-electrode materials for intermediate temperature solid oxide fuel cells under operational conditions

  • Muñoz-Gil, Daniel
  • Azcondo, María Teresa
  • Ritter, Clemens
  • Fabelo, Oscar
  • Pérez-Coll, Domingo
  • Mather, Glenn C.
  • Amador, Ulises
  • Boulahya, Khalid
The potential of the perovskite system Nd1-xSrxCoO3-δ (x = 1/3 and 2/3) as cathode material for solid oxide fuel cells (SOFCs) has been investigated via detailed structural, electrical, and electrochemical characterization. The average structure of x = 1/3 is orthorhombic with a complex microstructure consisting of intergrown, adjacent, perpendicularly oriented domains. This orthorhombic symmetry remains throughout the temperature range 373-1073 K, as observed by neutron powder diffraction. A higher Sr content of x = 2/3 leads to stabilization of the cubic perovskite with a homogeneous microstructure and with a higher oxygen vacancy content and cobalt oxidation state than the orthorhombic phase at SOFC operation temperature. Both materials are p-type electronic conductors with high total conductivities of 690 and 1675 S·cm-1 at 473 K in air for x = 1/3 and 2/3, respectively. Under working conditions, both compounds exhibit similar electronic conductivities, since x = 2/3 loses more oxygen on heating than x = 1/3, associated with a greater loss of p-type charger carriers. However, composite cathodes prepared with Nd1/3Sr2/3CoO3-δ and Ce0.8Gd0.2O2-δ present lower ASR values (0.10 ω·cm2 at 973 K in air) than composites prepared with Nd2/3Sr1/3CoO3-δ and Ce0.8Gd0.2O2-δ (0.34 ω·cm2). The high activity for the oxygen electrochemical reaction at intermediate temperatures is likely attributable to a large disordered oxygen-vacancy concentration, resulting in a very promising SOFC cathode for real devices. © 2020 Elsevier B.V., All rights reserved., We thank MICINN for funding the projects MAT2016-78362- C4-1-R, MAT2016-78362-C4-4-R, and RTI2018-095088-BI00 and ILL for allocation of beam time (experiment codes 5- 24-583 and CRG-D1B-19-379; DOI: 10.5291/ILL-DATA. CRG-2713). The authors also thank the “Comunidad de Madrid” and European Structural Funds for their financial support of the MATERYENER3-CM (S2013/MIT-2753) project. We are also grateful to the “Red de Excelencia” (MINECO, MAT 2017-090695-REDT) for facilitating collaboration between the Spanish groups. U.A. and M.T.A. also thank USP-CEU for financial support., The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.inorgchem.0c01049. (Figure S1) PXRD patterns Nd2/3Sr1/3CoO3−δ and Nd1/3Sr2/3CoO3−δ; (Figure S2) thermal evolution of the unit cell volume of Nd2/3Sr1/3CoO3−δ and (b) Nd1/3Sr2/3CoO3−δ in air; (Figure S3) NPD for Nd1/3Sr2/3CoO3−δ at 1073 K in air (Figure S4); mass loss and oxygen loss a function of temperature for Nd2/3Sr1/3CoO3−δ and Nd1/3Sr2/3CoO3−δ; (Table S1) nominal and experimental (determined by EDS) compositions for the Nd2/3Sr1/3CoO3−δ sample used for NPD and electrical characterization; (Table S2) nominal and experimental (determined by EDS) compositions for the Nd1/3Sr2/3CoO3−δ sample used for NPD and electrical characterization; (Table S3) structural parameters for Nd1−xSrxCoO3−δ obtained from joint fitting of NPD and PXRD data; (Table S4) selected structural information for Nd1−xSrxCoO3−δ (x = 1/3, 2/3) obtained from NPD data, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mechanochemical processing of BaZr1−yYyO3−δ (y = 0.15, 0.20) protonic ceramic electrolytes: Phase purity, microstructure, electrical properties and comparison with other preparation routes

  • Antunes, Isabel
  • Pérez-Coll, Domingo
  • Narendar, Narendar
  • Soares, Helena S.
  • Mather, Glenn C.
  • Frade, Jorge R.
  • Fagg, Duncan P.
BaZrO<inf>3</inf>-based materials have been intensively researched due to their potential application as high-temperature proton conductors in devices such as proton ceramic fuel cells (PCFCs), separation membranes and electrolysers. Nonetheless, their implementation in these devices has often been constrained due to their processing difficulties, namely the formation of Ba-deficient compositions, coexistence of separate perovskite phases or the formation of segregated phases of the acceptor dopant. In this context, the current article shows mechanosynthesis to be an efficient preparation method for Ba(Zr,Y)O<inf>3-δ</inf> materials, producing pure powders, containing nanometric crystallites, that offer good densification and grain growth. The phase formation, microstructure and electrical properties of the most promising BaZr<inf>1-y</inf>Y<inf>y</inf>O<inf>3-δ</inf> compositions, with yttrium contents of y = 0.15 (BZY15) and y = 0.20 (BZY20) are investigated and compared with literature data of materials made by other processing routes. Such a comparison highlights that phase separation of such compositions, commonly reported in the literature, does not occur for these mechanosynthesised materials of high homogeneity. Furthermore, high electrical performances can be obtained by this technique that can compete with some of the best reported in the literature. Electrical conductivity as a function of both oxygen and water partial pressure, in the temperature range of 550 °C − 850 °C, are measured for both compositions and the partial conductivities of protons, oxygen vacancies and electron holes are determined from the defect model. The electron-hole conductivity of BZY20 is observed to be higher than that of BZY15 under all conditions, while proton and oxide-ion conductivities are shown to be higher for the composition BZY15. © 2021 Elsevier B.V., All rights reserved., The authors acknowledge the projects, POCI-01-0145-FEDER-032241, UID/EMS/00481/2020-FCT – FCT - Fundação para a Ciencia e a Tecnologia; and CENTRO-01-0145-FEDER-022083 - Centro Portugal Regional Operational Programme (Centro2020), under the PORTUGAL 2020 Partnership Agreement, through the European Regional Development Fund (ERDF) and also the “Ministerio de Ciencia, Innovación y Universidades” Spain (RTI2018-095088-B-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of the addition mechanism of ZnO sintering aid on densification, microstructure and electrical properties of Ba(Zr,Y)O3-δ proton-conducting perovskite

  • Soares, Helena S.
  • Antunes, Isabel
  • Loureiro, Francisco J.A.
  • Pérez-Coll, Domingo
  • Willinger, Marc-Georg
  • Brandão, Ana D.
  • Mather, Glenn C.
  • Fagg, Duncan P.
We explore three different potential mechanisms to introduce 4 mol% ZnO sintering additive to the promising yttrium-doped barium zirconate (Ba(Zr,Y)O<inf>3-δ</inf>, BZY) proton conductor. The mechanisms involve Zn substitution for Y, Zr, or B-site cation excess. The addition of ZnO promotes high densification levels (up to 98% of the theoretical value) at 1300 °C, irrespective of the mechanism. However, scanning electron microscopy shows that the B-site cation excess mechanism leads to an impaired grain growth compared to the other mechanisms. Rietveld refinement of the lattice-parameters and scanning transmission electron microscopy-energy dispersive X-ray spectroscopy indicates that Zn resides in both grains and grain boundaries in all cases. Determination of partial conductivities demonstrates that the Zr substitution mechanism provides slightly higher values of bulk protonic conductivity, as well as a higher hydration enthalpy. In contrast, the B-site excess mechanism provides the highest specific grain-boundary conductivity, as a result of greater Zn segregation to the grain boundary. © 2021 Elsevier B.V., All rights reserved., The authors acknowledge the projects, UID/EMS/00481/2019-FCT, PTDC/CTM-CTM/2156/2020, PTDC/QUI-ELT/3681/2020, POCI-01-0247-FEDER-039926, POCI-01-0145-FEDER-032241, UIDB/00481/2020 and UIDP/00481/2020 and CENTRO-01-0145-FEDER-022083 - Centro Portugal Regional Operational Programme (Centro2020), under the PORTUGAL 2020 Partnership Agreement, through the European Regional Development Fund (ERDF) and MICINN, Spain (RTI2018-095088-B-I00)., Appendix A. Supplementary data The following is the Supplementary data at this article: https://doi.org/10.1016/j.ijhydene.2021.05.109, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

YBaCuO-type perovskites as potential air electrodes for SOFCs. The case of YSr2Cu2FeO7+δ

  • López-Paz, Sara A.
  • Marín-Gamero, Rafael
  • de Irujo-Labalde, Xabier
  • Sánchez-Marcos, Jorge
  • Pérez-Coll, Domingo
  • Álario-Franco, M.Ángel
  • García-Martín, Susana
The electrochemical properties of YSr2Cu2FeO7+δ with YBaCuO-type structure have been studied. The temperature dependent oxygen content of this oxide has a marked influence on its p-type conducting behavior, since topochemical oxygen release occurs on heating above 673 K while reversible oxygen uptake takes place on cooling. Mixed valence Fe3+/Fe4+ and Cu2+/Cu3+ in combination with anion vacancies within the oxygen-sublattice suggest mixed (electronic and ionic) conductivity in this oxide. Electrochemical measurements indicate that YSr2Cu2FeO7+δ shows high oxygen reduction reaction activity at intermediate temperatures, revealing its potential applications as an air electrode in SOFCs., We dedicate this article to the memory of Professor Emilio Morán Miguélez. We will always remember him. We thank the Agencia Estatal de Investigación (AEI)/Fondo Europeo de Desarrollo Regional (FEDER/UE) for funding the Projects PID2019-106662RB-C44 and MAT2016-78362-C4-4-R. D. P.-C. thanks the Project RTI2018-095088. S. L.-P. thanks the MECD for the grant FPU-016/00732. S. G.-M. and M. A. A.-F. also thank Fundación Ramón Areces (Project FRA2019/03)., Peer reviewed