Pasar al contenido principal

PRODUCCION ELECTROQUIMICA DE HIDROGENO MEDIANTE INTERFACES OPTIMIZADAS BASADAS EN GRAFENO. PHOTOGRAPH

PID2019-104272RB-C51

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Venciendo la degradación climática del patrimonio pétreo mediante recubrimiento con nanomateriales basados en carbono

  • González Domínguez, José Miguel
  • Búrdalo, Gabriel
  • Caldevilla, Pablo
  • Calvo Peña, Víctor
  • Fernández, Sagrario
  • González Campelo, D.
  • Martínez, Marta
  • Martínez García, Rebeca
  • Ortiz Marqués, Almudena
  • Palencia, Covadonga
  • Rodríguez Fernández, Carlos
  • Zelli, Flavia
  • Fernández-Raga, María
Resumen de la comunicación oral presentada en el XVII Simposio de Investigadores Jóvenes de la RSEQ, celebrado en la Universidad de Alcalá de Henares, 23-26 noviembre 2021., Cada año se notan más los efectos del cambio climático, que conllevan episodios de lluvia más agresivos y cambios térmicos más acusados. Estos cambios meteorológicos suponen un impacto muy grave, como el daño que pueden generar al patrimonio pétreo, altamente amenazado sobretodo en piedras blandas debido a su susceptibilidad a daños ocasionados por el agua. Las administraciones responsables de la protección del patrimonio tratan de paliar este desgaste con medidas que buscan proteger el bien de interés, pero bajo la máxima de que sean tratamientos que no alteren la apariencia física del mismo y que sean reversibles. Estos tratamientos que se realizan, si bien no son agresivos con el monumento, resultan muy costosos e ineficaces cuando, por causa de la escasez de recursos, no pueden realizarse con la frecuencia requerida (al menos una vez cada 5 años). Y esto conduce a que muchos monumentos esperando el tratamiento van abandonándose a su suerte. Nuestro equipo ya ha logrado encontrar y patentar una posible alternativa de protección basada en óxido de grafeno, de excelentes características: un recubrimiento transparente, más duradero, resistente e inocuo para la piedra. Además, se cumplen los requerimientos específicos de la protección monumental, que es no poner en riesgo el aspecto físico ni la estética del monumento. Además, mediante la actual financiación del MICINN se explorarán otros nanomateriales sostenibles y biodegradables. Esta prometedora idea supondrá que ni la economía, pues es barato y perdura su protección periodos superiores a los 10 años, ni el medio ambiente, pues buscamos recubrimientos que cumplan con los principios de sostenibilidad ambiental, fueran afectadas. Y además este proyecto combina estos trabajos y pruebas con el desarrollo de una herramienta digital SIG que permita evaluar y calcular el mejor tratamiento y su coste para distintos monumentos de un territorio, así como gestionar mejor los limitados recursos de las administraciones que custodian estos monumentos, indicando la fecha y localización de las aplicaciones y la prioridad de actuación bajo criterios objetivos., Overcoming the climatic degradation of the stone-based cultural heritage by shielding with sustainable nanomaterials (NANOSHIELD). Proyecto MICINN Retos PID2020-120439RA-I00.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Puntos de carbono poliméricos. Síntesis y desarrollo de nuevos nanomateriales de carbono fluorescentes y su implicación en la producción de hidrógeno sostenible

  • Álvarez Sánchez, Miguel Ángel
  • Martínez-Barón, Carlos
  • Hernández-Ferrer, Javier
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
Póster presentado en el XVII Simposio de Investigadores Jóvenes de la RSEQ (2021), celebrado en la Universidad de Alcalá de Henares, 23-26 noviembre., Los puntos de carbono poliméricos, pertenecientes a la familia de puntos de carbono (del inglés Carbon Dots), han despertado gran interés en los últimos años por sus excelentes propiedades de fluorescencia, que se puede modificar para que emitan en un rango variado de longitudes de onda. Esto, sumado a su bajo coste de síntesis, gran estabilidad fotoquímica, facilidad de funcionalización, baja toxicidad, elevada biocompatibilidad y solubilidad en agua, los posicionan como una potente alternativa a los puntos cuánticos convencionales, en su mayoría tóxicos por la presencia de metales pesados. Por todo ello, estos materiales resultan muy prometedores para aplicaciones en una gran variedad de campos, como son la biomedicina (diagnóstico, terapia, detección), la fotocatálisis (degradación de contaminantes) y la energía (fotovoltaica) entre otros. Los puntos poliméricos comúnmente emiten en el azul y su mecanismo de fluorescencia ha sido estudiado en profundidad. [5] Sin embargo, se han reportado pocos ejemplos de puntos poliméricos con una emisión de fluorescencia desplazada hacia el rojo. En este trabajo se presenta la producción, optimización y caracterización de puntos poliméricos solubles en agua, con fluorescencia en el verde y elevado rendimiento cuántico. Además, estos puntos poliméricos, implementados sobre un fotoánodo de óxido de titanio, han mejorado la fotoactividad del mismo para procesos de producción limpia de hidrógeno por escisión fotoelectroquímica del agua., Este trabajo ha sido financiado por MICINN/AEI con el proyecto PID2019-104272RB-C51/AEI/10.13039/50110 0 011033 y por el gobierno de Aragón, grupos reconocidos DGA-T03_20R. Agradecimientos a la DGA por la financiación del contrato predoctoral para el periodo 2019-2023., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nanocristales de quitina: Síntesis, caracterización y aplicaciones de un nanomaterial sostenible

  • Calvo Peña, Víctor
  • Ulcuango, Matías
  • González Domínguez, José Miguel
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen de la comunicación oral presentada en el XVII Simposio de Investigadores Jóvenes RSEQ, 23-26 noviembre 2021, celebrado en Alcalá de Henares., Los biopolímeros nanoestructurados tienen propiedades excepcionales, se extraen de fuentes naturales y tienen el potencial de sustituir plásticos de fuentes no sostenibles, como el petróleo. Estas cualidades se deben a su tamaño en la nano-escala (entre 1 y 100 nm), siendo el más investigado la nanocelulosa en sus distintas variedades. La quitina es el segundo biopolímero más abundante tras la celulosa y se encuentra en distintos seres vivos, por ejemplo, en los exoesqueletos de crustáceos y artrópodos, aportando rigidez y dureza. [3] La quitina se puede transformar en nanocristales de quitina (NCQ) a través de un proceso de hidrólisis ácida. [4] Distintas aplicaciones de los NCQ son la estabilización eficiente en agua de nanomateriales de carbono, la preparación de aerogeles o su uso como refuerzo de otros materiales. En este trabajo se presenta un método optimizado para la obtención de NCQ dispersos en agua con un rendimiento superior al 60% frente al 30% del método inicial. Se han caracterizado por diversas técnicas como difracción de rayos X, termogravimetría o microscopía de transmisión electrónica. Se ha probado también la capacidad de redispersión de los NCQ tras liofilizarlos, obteniendo una dispersión de calidad similar tras un proceso sencillo basado en ultrasonidos, lo cual no sucede con otros biopolímeros nanoestructurados, como los nanocristales de celulosa. Se ha probado el uso de estos NCQ como dispersante en tintas tanto de nanotubos de carbono de una sola capa como de nanofibras de carbono y su integración in situ y ex situ como refuerzo en xerogeles de nanocelulosa bacteriana. En definitiva, la presente comunicación demuestra el enorme potencial de los NCQ como agente dispersante, refuerzo, y aditivo sostenible para obtener desde una perspectiva verde una variedad de nanomateriales compuestos., Financiación del MICINN/AEI bajo los proyectos PID2019-104272RB-C51/AEI/10.13039/501100011033 y PID2020-120439RA-I00, y del Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_20R). Víctor C. agradece a la DGA por la financiación de su contrato predoctoral (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Fabricación de electrodos fotoactivos para la escisión de la molécula de agua a partir de tintas basadas en nanocelulosa

  • Martínez-Barón, Carlos
  • González Domínguez, José Miguel
  • Ansón-Casaos, Alejandro
  • Hernández-Ferrer, Javier
  • Maser, Wolfgang K.
  • Benito, Ana M.
Póster presentado en la Reunión Bienal de la Sociedad Española de Catálisis - SECAT 2021, celebrada en Valencia, del 18 al 20 de octubre 2021., Financiación de MICINN y AEI (PID2019-104272RB-C51/AEI/10.13039/501100011033), y Gobierno de Aragón (Grupo Reconocido GCNN T03_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Aerogeles unidireccionales de óxido de grafeno como soporte de electrocatalizadores

  • Carrera Jiménez, Clara
  • Hernández-Ferrer, Javier
  • González Domínguez, José Miguel
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • García-Bordejé, José Enrique
Póster presentado en la 9ª Jornada de Jóvenes Investigadores de Física y Química de Aragón, celebrada en Zaragoza el 16 de diciembre de 2021., El traslado de propiedades del grafeno hacia estructuras 3-D es de gran interés para la catálisis, electrocatálisis y el almacenamiento de energía. Sin embargo, el grafeno es proclive a apilarse, perdiendo sus propiedades y disminuyendo el área superficial. Los aerogeles de grafeno pueden evitar el problema del apilamiento, logrando mantener propiedades fundamentales como un gran área superficial, gran porosidad para la difusión de moléculas grandes, flexibilidad, resistencia mecánica y conductividad eléctrica. Aquí presentamos un método sintético para producir aerogeles de óxido de grafeno reducido (rGO) controlando la porosidad y la estructura interna, para su uso como soporte de electrocatalizadores en la reacción de evolución de hidrógeno (HER)., MICINN/AEI. PID2019-104272RB-C51/AEI/10.13039/501100011033 Grupo Reconocido DGA T03_20R, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Catalytic activity of MWCNT-based inks synthetized by different methods

  • Lorca, Sebastián
  • Santos, Florencio
  • Padilla Martínez, Javier
  • Urbina, Antonio
  • González Domínguez, José Miguel
  • García-Bordejé, José Enrique
  • Álvarez Sánchez, Miguel Ángel
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Fernández Romero, Antonio J.
Abstract of the poster presented at "Current Trends in Electrochemistry", 41st Meeting of the Electrochemistry Group of the Spanish Royal Society of Chemistry and 1st French-Spanish Atelier/Workshop on Electrochemistry, Paris (July 6 - 9, 2021)., Research on new catalyst materials for the oxygen reduction reaction (ORR) is the main goal for many research groups around the world, due to its application in fuel cells and metal/air batteries. ORR mainly occurs by two pathways, in alkaline media, the direct four-electron transfer pathway from O2 to OH- or in a two-steps mechanism, where hydrogen peroxide (HO2-) is formed in the first reaction. On fuel cells and metal air batteries applications, the catalyst must be optimized to get the oxygen reduced directly to water through the 4 electrons mechanism1. Due to high price of the precious metals, new materials are tested to be used as catalyst in ORR. Among them, researchers have focused their attention mainly on metal oxides, perovskites or carbonaceous materials. In this communication, we have studied four carbonaceous-based inks synthetized by ultrasonic or hydrothermal methods2, using a rotating ring-disk electrode (RRDE) (Figure 1.A). The production of HO2- (%HO2-), transferred electrons and others parameters will be analyzed and the results will be discussed in depth. Finally, the inks were used as catalysts in the cathode of a PVA-KOH-based zinc/air batteries to replace the most widely used catalyst to date, MnO2, The authors thank the financial support from Fundación Séneca (Región de Murcia, Spain; Ref: 20985/PI/18 and 19882-GERM-15), Spanish Agencia Estatal de Investigación (PID2019-104272RB-C55/ AEI/10.13039/501100011033 and PID2019-104272RB-C51/AEI/10.13039/501100011033), and Gobierno de Aragón (DGA T03_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nanocristales de quitina y sus híbridos funcionales con potenciales aplicaciones en energía y sostenibilidad

  • Calvo Peña, Víctor
  • Ulcuango, Matías
  • González Domínguez, José Miguel
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen de la comunicación oral presentada en la 9ª Jornada de Jóvenes Investigadores de Física y Química de Aragón, celebrada el 16 de diciembre de 2021 en Zaragoza., Los biopolímeros nanoestructurados tienen propiedades excepcionales, se extraen de fuentes naturales y tienen el potencial de sustituir plásticos de fuentes no sostenibles, como el petróleo. Estas cualidades se deben a su tamaño en la nano-escala (entre 1 y 100 nm), siendo el más investigado la nanocelulosa en sus distintas variedades [1,2]. La quitina es el segundo biopolímero más abundante tras la celulosa y se encuentra en distintos seres vivos, por ejemplo, en los exoesqueletos de crustáceos y artrópodos, aportando rigidez y dureza [3]. La quitina se puede transformar en nanocristales de quitina (NCQ) a través de un proceso de hidrólisis ácida [4]. Distintas aplicaciones de los NCQ son la estabilización eficiente en agua de nanomateriales de carbono, la preparación de aerogeles o su uso como refuerzo de otros materiales [5,6]. En este trabajo se presenta un método optimizado para la obtención de NCQ dispersos en agua con un rendimiento superior al 60% frente al 30% del método inicial. Se han caracterizado por diversas técnicas como difracción de rayos X, termogravimetría o microscopía de transmisión electrónica. Se ha probado también la capacidad de redispersión de los NCQ tras liofilizarlos, obteniendo una dispersión de calidad similar tras un proceso sencillo basado en ultrasonidos, lo cual no sucede con otros biopolímeros nanoestructurados, como los nanocristales de celulosa. Se ha probado el uso de NCQ como dispersante en tintas tanto de nanotubos de carbono como de nanofibras de carbono y su integración in situ y ex situ como refuerzo en xerogeles de nanocelulosa bacteriana. En definitiva, la presente comunicación demuestra el enorme potencial de NCQ como agente dispersante, refuerzo, y aditivo sostenible para obtener desde una perspectiva verde una variedad de nanomateriales compuestos., Financiación del MICINN/AEI bajo los proyectos PID2019-104272RB-C51/ AEI/10.13039/501100011033 y PID2020-120439RA-I00, y del Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_20R). Víctor C. agradece a la DGA por la financiación de su contrato predoctoral (Ref. CUS/581/2020).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Carbon nanostructures: Building blocks for sustainable layered photoelectrochemical device structures

  • Benito, Ana M.
  • Ansón-Casaos, Alejandro
  • Hernández-Ferrer, Javier
  • González Domínguez, José Miguel
  • Ciria, José Carlos
  • Maser, Wolfgang K.
1 figura.-- Resumen del póster presentado en el congreso ChemOnTubes 2022, celebrado en Donostia-San Sebastián, del 24 al 28 de abril., Layered film architectures fabricated through liquid phase processing technologies enjoy great interest for the development of optoelectronic and photoelectrochemical devices, whereby aspects of sustainability are becoming of increased importance. In this presentation we show that carbon nanostructures, such as graphene oxide, carbon nanotubes and carbon dots with their unique electrical and optical properties can be sustainably processed from surfactant-free aqueous dispersions into layered photoelectrodes. Effects of nanostructurization for the development of functional hybrids and environmentally friendly water-based dispersions, as well as the relevance of interface interactions for attaining enhanced charge-transfer and photoelectrochemical performance of the photoelectrode with respect to water-splitting activities are discussed., Spanish MICINN/AEI: PID2019-104272RB-C51/AEI/10.13039/501100011033; Government of Aragón: Grupos Reconocidos DGA T03_20R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Graphene Oxide: The spring-dance of electrons ("Una Jota Aragonesa")

  • Maser, Wolfgang K.
  • Palacios-Lidón, E.
  • Colchero, J.
  • Ortuño, Miguel
  • Colom, E.
  • Somoza, Andrés M.
  • Benito, Ana M.
Resumen del póster presentado en el congreso ChemOnTubes 2022, celebrado en Donostia-San Sebastián (España), del 24 al 28 de abril., Graphene oxide is a unique nanoscale object with tunable electronic properties, largely influenced by the presence of oxygen functional groups located on the basal plane [1-3]. In this work shine light on the nanoscale charge density and dynamics of isolated GO nanosheets, probed by Kelvin Probe Microscopy [4]. We visualize the existence of charge-domains with respective charge interactions. We further reveal short range fluctuations of jumping electrons and the existence of very long-term relaxation times. The experimental findings are consistent with theoretical simulations, underlining that graphene oxide needs to be understood in terms of an electron glass revealing hopping transport between charge-domains., Spanish MICINN/AEI: Projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2019-104272RB-C52/AEI/10.13039/501100011033; Government of Aragón: Grupos Reconocidos DGA T03_20R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Single-walled carbon nanotubes/nanocellulose hybrid films: towards the development of PEC water splitting photoanodes

  • Martínez-Barón, Carlos
  • González Domínguez, José Miguel
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen de la comunicación oral presentada en el Congreso ChemOnTubes 2022, celebrado en Donostia-San Sebastián (España) del 24 al 28 de Abril., Hydrogen is considered as one of the most suitable alternatives to fossil fuels if produced from water using renewable resources. Particularly, photoelectrochemical (PEC) water splitting is a well-known technology that allows to obtain green hydrogen through a combination of electricity and sunlight. This process requires photoelectrodes composed of a conductive substrate and a photoactive phase. The present work demonstrates that singlewalled carbon nanotubes (SWCNTs) can be processed along with nanocellulose, a biocompatible adjuvant that enables waterborne inks, into conductive films [1]. SWCNT inks were spray-coated over glass substrates in the form of films. Their low electrical resistivity values (Figure 1a) highlight that SWCNT films are valuable alternatives to typically employed opaque substrates in electrochemical devices, such as pyrolytic graphite. Subsequently, a TiO2 layer was deposited onto the SWCNT films, thus rendering the desired photoanodes (Figure 1b). Electrochemical measurements show that the as-prepared photoanodes display a noticeable photocurrent (Figure 1c), being a clear indicative of their water splitting activity. This is an unprecedented feature for this type of electrode configuration., Spanish MICINN/AEI: PID2019-104272RB-C51/AEI/10.13039/501100011033; Government of Aragón: Grupos Reconocidos DGA T03_20R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Highly fluorescent green emissive Carbon Dots: synthesis, characterization and their use in green H2 production

  • Álvarez Sánchez, Miguel Ángel
  • Martínez-Barón, Carlos
  • Hernández-Ferrer, Javier
  • Ansón-Casaos, Alejandro
  • Calvo Peña, Víctor
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
1 figure.-- Comunicación oral presentada en el congreso ChemOnTubes 2022, celebrado en San Sebastián, del 24 al 28 abril., Carbon Dots (CDs) have attracted considerable attention due to their excellent photoluminescence (PL), high photochemical stability, easy functionalization, water solubility, low toxicity and good biocompatibility, among others. All these properties elevate CDs as a potential alternative to conventional quantum dots, thus overcoming issues of toxicity due to the presence of heavy metals [1]. The outstanding properties of CDs have enabled their application in many research fields, such as biomedicine [2], photocatalysis, photovoltaics, photoelectrochemistry [3], and sensing. Actually, most of the reported CDs show intrinsic blue emission, whose PL mechanism has been studied in depth [4]. However, there is increased research activity to obtain CDs with longer emission wavelengths. Herein, we present the bottom-up microwave synthesis, optimization and characterization of water-soluble CDs with high PL quantum yield and green emission. Moreover, the intense PL is maintained even in the solid state, when embedded in a biopolymer matrix. Finally, we demonstrate that the CDs show great promise as sensitizers in TiO2 photoanodes, integrated into a photoelectrochemical cell for the production of green hydrogen., Spanish MICINN/AEI: PID2019-104272RB-C51/AEI/10.13039/501100011033; Government of Aragón: Grupos Reconocidos DGA T03_20R and PhD grant of MAA IIU/796/2019., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Titanium dioxide electrodes for water photo-electrolysis: modelling of photoelectrochemical processes

  • Ansón-Casaos, Alejandro
  • Ciria, José Carlos
  • Martínez-Barón, Carlos
  • Benito, Ana M.
  • Maser, Wolfgang K.
1 figure.-- Abstract of the work presented at the EHEC 2022, European Hydrogen Energy Conference 18-20 May, 2022. Madrid, Spain., Solar photoelectrolysis of water is considered as a promising route towards green hydrogen production. Since its first demonstration in 1969 [1], improving the efficiency of the process remains the major challenge. Current research efforts focus on the development of improved photoelectrodes enabling higher photocurrents and larger solar-to-hydrogen conversion. Of special interest are photoactive semiconductors being used as photoanodes. Employing concepts of nanostructuring and doping combined with liquid phase technologies for constructing favorable layered configurations, metal oxides offer strategic advantages when it comes towards the use of abundant non-critical materials and sustainable fabrication of efficient large-area photoanodes. Deeper comprehension of the underlying photoelectrochemical processes provides the necessary feedback to a successful progress. In this presentation, boron-doped nanostructured TiO2 film electrodes are used as photoanode. We show that its photoelectrochemical performance can be successfully described by mathematical and physical models. This finding is of wider general interest to understand and improve the performance of nanostructured layered photoanode architectures., Financial support from Spanish MICINN/AEI under project PID2019-104272RB-C51/AEI/10.13039/ 501100011033 and the Diputación General de Aragón under project T03_20R (Grupo Reconocido) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Oxygen reduction reaction by cobalt dispersed on carbon nanostructured materials

  • Hernández-Ferrer, Javier
  • Carrera Jiménez, Clara
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • García-Bordejé, José Enrique
1 figura.-- Resumen del póster presentado en el IX International Symposium on Carbon for Catalysis, CARBOCAT, 28-30 junio 2022, Zaragoza, España., Transition metal modified carbon nanomaterials are being widely investigated as electrocatalysts for the oxygen reduction reaction, since they are promising candidates for the replacement of precious metal catalysts in fuel cells, as well as other applications. These materials possess a high versatility; depending on the preparation conditions, and subsequently, the structure and electronic environment of the supported cobalt (single site, nanoparticulate), high activities and selectivities may be achieved for both the four-electron and two-electron pathways. The nature of carbon support is also known to be of crucial importance in these materials [1]. Heteroatom inclusion (N-doping) and the porosity of the material are some of the key parameters than can be explored, and tailored towards the desired application. In this work, Multi-walled carbon nanotubes (MWCNTs, Nanocyl), electrochemically synthesized nitrogen-doped graphene quantum dots (NGQDs), and graphene aerogels (GA) were used as support for cobalt electrocatalysts., Ministerio de Ciencia e Innovación (PID2019-104272RB-C51/AEI/10.13039/501100011033 project), and Gobierno de Aragón (Grupo Reconocido T03_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Photoelectrocatalytic water splitting on carbon dot/titania electrodes with methanol oxidation

  • Ansón-Casaos, Alejandro
  • Hernández Ferrer, Mariano
  • Lira-Cantú, Mónica
  • Benito, Ana M.
  • Maser, Wolfgang K.
1 figure, 2 tables.-- Abstract of the poster presented at the 9th International Symposium on Carbon for Catalysis, IX CarboCat, 28th-30th June, Zaragoza, Spain., Short-chain alcohols such as methanol (MeOH) work well as hole scavengers in the photocatalytic water splitting on TiO2. Besides, MeOH is widely studied as a model pollutant in water. Both ideas are often combined to achieve efficient water purification processes with the simultaneous production of hydrogen. In this communication, we present a photoelectrochemical study on carbon dot (CD)/TiO2 electrodes., Financial support from Spanish MICINN/AEI under project PID2019-104272RB-C51/AEI/ 10.13039/501100011033 and the Diputación General de Aragón under project T03_20R (Grupo Reconocido) is acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Unidirectionally porous RGO aerogels as electrocatalyst support

  • Carrera Jiménez, Clara
  • Hernández-Ferrer, Javier
  • González Domínguez, José Miguel
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • García-Bordejé, José Enrique
2 figures.-- Abstract of the poster presented at the IX Carbocat 2022, 28th-30th June, Zaragoza, Spain., Interest in 3D-graphene structures is increasing as a way to translate the characteristics of individual graphene sheets onto the macroscale. Among them, graphene aerogels offer useful properties such as high specific surface area, open porous network allowing ion transport, flexibility, tough mechanical strength while constituting conductive framework structures.[1] Gelation of graphene oxide (GO) dispersions is the most common way to obtain graphene aerogels.[2] For this, GO dispersions are subjected to an hydrothermal treatment in an autoclave that leads to the removal of oxygenated functional groups. This reduction directly increases the hydrophobicity and reduces the amount of surface charges, producing the crosslinking of the reduced GO (RGO) sheets. Therefore, phase separation takes place inducing the hydrogel formation. Eventually, a further freeze-drying step allows to obtain the desired RGO aerogels. In this work, different conditions of the hydrothermal process such as time or pH have been studied. pH has been found to be key in the reduction degree and morphology of the final RGO hydrogel and subsequent transformation into an aerogel. Varying from acidic pH to basic pH, which is attained by the addition of ammonia during the hydrogel formation, an increase of the porosity, is observed., Spanish MICINN/AEI: PID2019- 104272RB-C51/AEI/10.13039/501100011033; Government of Aragón: Grupos Reconocidos DGA T03_20R and PhD grant of CC IIU/796/2019.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Metal-free dyes with deep HOMO level for TiO2 sensitization

  • Ansón-Casaos, Alejandro
  • Orduna, Jesús
  • Martínez-Barón, Carlos
  • Blanco Cambronero, Aitana
  • Hernández-Ferrer, Javier
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Blesa, María Jesús
Work presented at the XI Franco-Spanish Workshop IBERNAM-CMC2 – 9-10th November 2023, Zaragoza (Spain)., Photoelectrochemical (PEC) water splitting is being intensively studied as a method for green hydrogen production and artificial photosynthesis. Specifically, titanium dioxide (TiO2) nanoparticles show remarkable properties as a photocatalyst and for the preparation of nanostructured photoanodes. However, as a wide bandgap semiconductor, TiO2 is only active under UV irradiation, and sensitization with organic dyes would be a convenient strategy to improve its solar conversion efficiency. In our previous work, we studied the sensitization of the TiO2 electrode through the adsorption of a metal-free donor-π-acceptor (D-π-A) dye molecule (AT-Pyri) [1]. The AT-Pyri molecule consists of an aniline donor, thiophene π-spacer, and a pyrimidine unit as the acceptor part. We showed that the AT-Pyri/TiO2 electrode was in fact active for water splitting under a wide range of visible light wavelengths, up to 600 nm. However, the system visibly degraded during transient photocurrent measurements under potentiostatic conditions in the Na2SO4 aqueous electrolyte. As a possible source of instability, we considered the oxidation potential (Eox) of AT-Pyri, which was determined to be +0.88 V vs. SHE, thus above the O2/H2O reduction potential. In this work, we evaluate the energy levels of two alternative dye molecules by means of DFT theoretical calculations. In terms of the chemical structure, we follow a simplification strategy, resulting in π-A type molecules. We select the bithiophene ring as the π-spacer, and either cyanoacetic acid (-CNCOOH) or pyrimidine (Pyri) as the acceptor and anchoring group (Figure 1). Both dyes fulfil theoretical requirements to become TiO2 sensitizers in a water splitting process, with Eox > EO2/H2O (Table 1). Next, we perform the laboratory synthesis and characterization of both dyes, which show yellowish colors. Nanostructured TiO2 electrodes on FTO/glass substrates are prepared by screen printing, and dye adsorption is successfully accomplished by immersion of TiO2 electrodes in CH2Cl2 solutions. However, the TT-CNCOOH dye desorbs from the TiO2 support and is solubilized when the electrode is put in contact with electrolytic Na2SO4 and phosphate buffer solutions, so it is not used for PEC studies. The complete PEC characterization of the TT-Pyri/TiO2 electrode is performed in a 3-electrode cell with aqueous Na2SO4 electrolyte, and under simulated solar light irradiation. The electrode is stable under cyclic voltammetry conditions between -0.5 and 0.4 V vs. Ag/AgCl. Moreover, the electrode keeps its yellow color after a 5 min photocurrent measurement under light irradiation periods of 15 s and a constant potential of 0 V vs. Ag/AgCl. The photocurrent is multiplied by 1.6 and 12.5 In the presence of glycerol and triethanolamine as sacrificial agents, respectively. The dye sensitization effect was also proved by experiments using a monochromator. However, as it is observed after a continuous photocurrent measurement for 2 h, the long-time stability is still hindered by a slow unknown degradative mechanism, which requires further investigation, Financial support from Spanish MICINN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” under project grants PID2019-104272RB-C51, PID2022-139671OB-I00 and PID2019-104307GB-I00, and the Gobierno de Aragón (DGA) under projects T03_23R and E47_23R (Grupos de Investigación Reconocidos) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Effect of post activation treatment and presence of minor amount of metal on nitrogen-doped carbon materials derived from laser-assisted pyrolysis for oxygen reduction reaction

  • Pakrieva, Ekaterina
  • Hernández-Ferrer, Javier
  • Martínez, Gema
  • Balas, Francisco
  • Hueso, José L.
  • García-Bordejé, José Enrique
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Santamaría, Jesús
Trabajo presentado a las XXXVII Jornadas Nacionales de Ingeniería Química: El puente hacía un futuro sostenible, celebradas en Castellón del 13 al 15 de septiembre de 2023.-- Temática: Energía y Sostenibilidad., The authors thank the Spanish Ministry of Science and Innovation (LAERTES project) and the European Commission (ERC-Advanced Grant CADENCE) for funding. The synthesis of materials has been performed by the Platform of Production of Biomaterials and Nanoparticles of the NANBIOSIS ICTS, more specifically by the Nanoparticle Synthesis Unit of the CIBER in BioEngineering, Biomaterials & Nanomedicine (CIBERBBN). The characterization has been carried out in the ELECMI-ICTS facilities. Financial support from Diputación General de Aragón under project T03_23R (Grupo Reconocido), Projects PID 2020-119160RB-C21 and PID2019-104272RB-C51 funded by MCIN/AEI/10.13039/501100011033 are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Sustainable fabrication of carbon nanotube electrodes based on chitin nanocrystals: unraveling Faradaic charge transfer phenomena

  • Calvo Peña, Víctor
  • Martínez-Barón, Carlos
  • Vázquez Conejo, Benjamín
  • Domínguez Alfaro, Antonio
  • Paleo, Antonio J.
  • Ansón-Casaos, Alejandro
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
Work presented at the XXV Meeting of The Portuguese Electrochemical Society (SPE2023), 30th august-1st september 2023, Coimbra (Portugal), The use of carbon nanomaterials is widespread in the scientific community due to their excellent optoelectronic and mechanical properties. In particular, carbon nanotubes (CNTs) are typically employed in electrochemical devices for different purposes, ranging from sensing to energy storage applications [1]. An effective way to transfer CNT properties from the nano- to the microscale level is by preparing CNTs-based films [1 – 3]. Commonly, CNTs are dispersed in organic solvents or water by means of surfactants, which can be detrimental for the final application. Aiming to develop sustainable CNT electrodes, chitin nanocrystals (ChNCs) emerge as a promising adjuvant towards the fabrication of waterborne environmentally-friendly CNTs inks. The present work demonstrates the feasibility of ChNCs to render stable aqueous inks of CNTs. These inks were subsequently employed for the preparation of film electrodes over glass substrates by means of spray coating. Once deposited, thickness and surface morphology of the CNT conductive films were evaluated, unraveling remarkable electrical conductivities ranging from 4.1 to 9.5 (S·cm-1). Furthermore, electrochemical measurements of the CNTs/ChNCs electrodes were carried out in a three-electrode cell. Faradaic transfer properties were evaluated using three different redox probes: ferricyanide, ascorbic acid and hydroquinone. For instance, cyclic voltammograms using the ferricyanide probe revealed enhanced charge transfer phenomena when thermally treating both CNTs/ChNCs electrodes in inert atmosphere. This fact has been supported by the standard electrochemical rate constant (k0), which decreased one order of magnitude in both cases after the thermal treatment, having a k0 of 4.1·10-5 for SWCNTs and 3.6·10-4 (cm·s-1) for MWCNTs. These values are in the range of other electrode materials [3, 4], revealing the potential of the herein shown approach., Spanish MICINN/AEI (PID2019-104272RB-C51/AEI/10.13039/501100011033, PID2020-120439RA-I00), Spanish CSIC (PIE iniciación, ref. 202280I007), Gobierno de Aragón (DGA- T03_23R and CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Caracterización de un recubrimiento de grafeno en un fotoánodo de TiO2 sensibilizado con un nuevo colorante de tipo D-pi-A

  • Ansón-Casaos, Alejandro
  • Angoy, Sergio
  • Colom, E.
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Blesa, María Jesús
Póster presentado en la XV Reunión del Grupo Español del Carbón, celebrada del 24 al 27 de abril de 2022 en Granada (España)., Proyectos financiados por el MICINN y la AEI (PID2019-104272-RB-C51/AEI/10.13039/501100011033 y PID2019-104307GB-I00/AEI/10.13039/501100011033) y el Gobierno de Aragón (Grupo Reconocido T03-20R y E47-20R)., Peer reviewed