Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

FDOT reconstruction and setting optimization using singular value analysis with automatic thresholding

  • Chamorro Servent, Judit
  • Aguirre, Juan
  • Ripoll Lorenzo, Jorge
  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
2009 IEEE Nuclear Science Symposium Conference Record (NSS/MIC), Orlando, Florida, 25-31 October 2009, Fluorescence Enhanced Diffuse Optical Tomography (FDOT) retrieves 3D distributions of fluorophore concentration in small animals, non-invasively and in vivo. The FDOT problem can be formulated as a system of equations, d=Wf, where W is a weight matrix that couples the measurements (d) to the unknown spatial distribution (f) of the fluorophore concentration (forward problem). The Singular Value Decomposition (SVD) of W has been previously employed to solve the inverse problem (image reconstruction) and to study the imaging performance of FDOT. To achieve good image quality it is necessary to determine the number of useful singular values to retain. We use an automatic method that analytically calculates a threshold to select the significant singular values for SVD reconstruction of FDOT experiments previously validity in our laboratory. Afterwards, this work appraises the effect of different settings of the acquisition parameters (distribution of mesh points, density of sources and detectors) of a parallel-plate noncontact FDOT, in order to achieve the best possible imaging performance, i.e., minimum number of singular values of W, maximum information content in acquired measurements and minimum computational cost. We conclude that the use of a mesh with lower density in the direction perpendicular to the plates achieves better performance than the usual isotropic mesh points distribution. Any increase in the number of mesh points, sources and detectors at distances shorter than the photon mean free path leads to slight improvements in image quality while increasing computational burden., This work is supported in part by Fundacion Caja Navarra (#12180), Ministerio de Ciencia e Innovacion (TEC2008-06715 and TEC2007-64731) and EU-FP7 project FMTXCT-201792.
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Complete Scheme for Beam Hardening Correction in Small Animal Computed Tomography

  • Molina, Claudia de
  • Sisniega, Alejandro
  • Desco Menéndez, Manuel
  • Vaquero López, Juan José
  • Abella García, Mónica
Proceedings of: 2012 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC). Anaheim, California, USA. October 29 - November 3, 2012, CT images are often affected by beam hardening artifacts (cupping and dark streaks) due to the polyenergetic nature of the X-ray beam. FDK is still the favorite reconstruction algorithm in commercial X-ray CT scanners. Several correction methods have been proposed to be included in an FDK reconstruction scheme. We present a complete correction scheme for beam hardening artifact correction in an FDK based reconstruction scenario that accounts for both cupping artifact and dark streaks avoiding the need of the knowledge of the source spectrum. The proposed correction scheme includes two steps: a linearization step of projection data and a post-reconstruction step. The first step assumes that the object is homogeneous and uses a linearization function that is calculated empirically in a previous calibration process with a simple phantom. The second step is based in the theoretical study described in Joseph and Spital, and calculates the non-linear beam-hardening distortion from a bone segmentation of the reconstructed image. The proposed correction scheme was evaluated in real studies acquired with a cone-beam micro-CT scanner: three polymethylmethacrylate cylinders (3, 4, and 6 cm diameter), a two-density cylindrical phantom and three rodent studies. Results show an average cupping reduction of 84 % in the three homogeneous phantoms and an average dark streaks reduction of 80 % in the two-density phantom and the three rodent studies. The proposed method could be incorporated easily in any cone beam micro-CT scanner and substitutes the need of the knowledge of the spectrum by empirical measurements and two parameters. Since it is based on empirical measurements, we expected to correct the artifacts derived from scattering., This work was supported in part by projects TEC2008-06715 and TEC2007-64731 (Ministerio de Ciencia e Innovaci6n), EU-FP7 FMTXCT-201792, ARTEMIS S2009/DPI-1802 (Comunidad de Madrid), and European Regional Development Funds (FEDER) and CDTI under the CENIT program (AMIT project, CEN-20101014)., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Automatic Monte-Carlo Based Scatter correction for X-ray Cone Beam CT using General Purpose Graphic Processing Units (GP-GPU): a Feasibility study

  • Sisniega, Alejandro
  • Abella García, Mónica
  • Desco Menéndez, Manuel
  • Vaquero López, Juan José
  • Lage Negro, Eduardo
Proceedings of: 2011 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC). Valencia, Spain, 23-29 October 2011, Scattered photons highly degrade the quality of X-ray images and their effect has become more important due to the increasing interest in cone-beam geometry for the acquisition of CT (CBCT) and micro-CT data. The random nature of scatter events and the great influence of the sample suggest that the most accurate methods for their estimation are Monte Carlo (MC) techniques, but their use is usually hampered by the large computation time required to obtain an acceptable estimation of the scattered radiation. We present an approach for scatter correction in CBCT by MC estimation, speeding up the computation by means of general purpose graphic processing units (GPGPU) and developing a framework for the automatic correction and reconstruction of projection data. The method consists of five stages: FDK reconstruction of the original data; histogram based automatic segmentation of the volume assigning a material and density to each voxel; fast MC estimation of the scatter signal; denoising of the independent scatter components and subtraction from original data; and FDK reconstruction of the corrected data. Every stage runs in a GPGPU using Nvidia CUD A. The MC stage is based on the MC-GPU code. To simulate polychromatic X-ray beams, the Spektr model is used to generate the source spectrum. Photon scattering is forced in order to reduce the number of events needed to obtain an acceptable scatter image weighting the photon histories to assure the correctness of the result. Further reduction in the variance is obtained by split the photon in several virtual photons which are forced point to the detector and are transported with no further interaction to the detector's surface. Furthermore, the divergence of the execution path of GPGPU kernels has been minimized. These techniques achieve a reduction of the variance of the scatter signal of two orders of magnitude and the final efficiency is improved by a factor of ~30., This work has been partially funded by the Spain Ministry of Education, FPU program; Spain Ministry of Science and Innovation, projects TEC2008-06715 and TEC2007-64731; CDTI under the CENIT Programme (AMIT Project); Comunidad de Madrid (ARTEMIS S2009/DPI-1802); and EU-FP7, FMTXCT-201792, Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Use of Split Bregman denoising for iterative reconstruction in fluorescence diffuse optical tomography

  • Chamorro Servent, Judit
  • Pérez-Juste Abascal, Juan Felipe
  • Aguirre, Juan
  • Arridge, Simon
  • Correia, Teresa
  • Ripoll Lorenzo, Jorge
  • Desco Menéndez, Manuel
  • Vaquero López, Juan José
Fluorescence diffuse optical tomography (fDOT) is a noninvasive imaging technique that makes it possible to quantify the spatial distribution of fluorescent tracers in small animals. fDOT image reconstruction is commonly performed by means of iterative methods such as the algebraic reconstruction technique (ART). The useful results yielded by more advanced l1-regularized techniques for signal recovery and image reconstruction, together with the recent publication of Split Bregman (SB) procedure, led us to propose a new approach to the fDOT inverse problem, namely, ART-SB. This method alternates a cost-efficient reconstruction step (ART iteration) with a denoising filtering step based on minimization of total variation of the image using the SB method, which can be solved efficiently and quickly. We applied this method to simulated and experimental fDOT data and found that ART-SB provides substantial benefits over conventional ART, This work was supported by Spanish Ministry of Science and Innovation (FPI program, TEC2008-06715), EU-FP7 project FMTXCT-201792, the Community of Madrid (ARTEMIS S2009/DPI-1802), European Regional development Funds (FEDER), and CDTI under the CENIT program (AMIT Project, CEN-20101014)., (European Community's Seventh Framework Program), Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Viabilidad del uso de fotodetectores SiPM en sistemas PET/IRM

  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
  • Vicente, Esther
  • España, Samuel
  • Picado, E.
  • Cal González, Jacobo
  • Fraile, L. M.
  • Herraiz, J. L.
  • Udías, José Manuel
Actas de: XXVIII Congreso Anual de la Sociedad Española de Ingeniería Biomédica (CASEIB 2010). Madrid, 24-26 de noviembre de 2010., El fotomultiplicador de silicio (SiPM) es un detector compuesto por una matriz de fotodiodos funcionando en modo avalancha, también conocido como modo Geiger. Se trata de un dispositivo de alta eficiencia en la detección de fotones que, por tratarse de un semiconductor, es compacto, teóricamente insensible a campos magnéticos, y de bajo coste. Además, la electrónica asociada es sencilla y podría integrarse en el mismo dispositivo. Estas características hacen de este componente un buen candidato para construir detectores de rayos gamma para imagen médica nuclear (PET y SPECT). En este trabajo se evalúan las prestaciones de tres detectores diferentes de 1 x 1 mm2 y una matriz de 2 x 2 SiPMs (6 x 6 mm² área activa total). Se ha analizado la dependencia de los parámetros operacionales del dispositivo en presencia de campos magnéticos estáticos intensos y de los campos de radiofrecuencia generados por un sistema de IRM preclínico, en condiciones extremas de trabajo en cuanto a intensidad y frecuencia de conmutación de los gradientes de campo. Al mismo tiempo se ha verificado que la presencia de estos dispositivos en la zona de imagen de la RM no afecta a la calidad de la misma., Este trabajo ha sido financiado por los proyectos TEC2007-64731, TEC 2008-06715-C02-1 del Ministerio de Ciencia e Innovación, por la RETIC-RECAVA del Ministerio de Sanidad y Consumo, por el programa ARTEMIS S2009/DPI-1802 de la Comunidad de Madrid, por el proyecto europeo FMT-XCT FP7-201792, los programas FPA2007-62216, TEC2008-06715-C02-01, UCM (Grupos UCM; 910059), CPAN (Consolider-Ingenio 2010) y CSPD-2007-00042. Parte de los cálculos realizados en este trabajo se han hecho en el ‘‘High Capacity Cluster for Physical Techniques’’ de la UCM, financiados en parte por la UE bajo el programa FEDER, y en otra parte por la UCM., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Reconstrucción de Tomografía Óptica Difusiva por Fluorescencia usando Compressed Sensing Split Bregman

  • Chamorro Servent, Judit
  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
  • Abascal, Juan
  • Aguirre, Juan
Actas de: XXIX Congreso Anual de la Sociedad Espñaola de Ingeniería Biomédica (CASEIB 2011). Cáceres, 16-18 Noviembre 2011., La Tomografía Óptica Difusiva por Fluorescencia (fDOT) es una técnica de imagen molecular que proporciona, de manera no invasiva e in-vivo, la distribución espacial 3D de la concentración de sondas fluorescentes en animales pequeños. Para asegurar una buena resolución de imagen es necesario un gran número de medidas. En este trabajo, proponemos el uso de 'Compressed Sensing Split Bregman' (CS-SB) como método de reconstrucción para fDOT. Por un lado, la técnica 'Compressed Sensing' permite reconstruir señales submuestreadas en ciertas condiciones. Por otro lado, la reciente aparición del método Split Bregman facilita la solución del problema, en términos de coste computacional. Presentamos resultados de CS-SB aplicado a datos simulados de fDOT. Aunque este es un trabajo preliminar, orientado al uso de CS-SB como método de reconstrucción, el objetivo final, en un futuro próximo, es utilizar dicho método para demostrar qué tanto por ciento de fuentes podemos ignorar en el momento de la adquisición manteniendo una buena calidad de imagen con una adquisición acelerada., Este trabajo due financiado en parte por el Ministerio de Ciencia e Innovación de España (FPI, TEC2008-06715 y TEC2007-64731), el proyecto europeo EU-FP7 FMTXCT-20172, la Comunidad de MAdrid (ARTEMIS S2009/DPI-1802), European Regional Development Funds (FENDER) y CDTI bajo el programa CENIT (Proyectp AMIT, CEN-20101014)., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Design of DOI PET detector Modules using phoswich and SIPMs: First Results

  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
  • Lage Negro, Eduardo
  • Sánchez, J. J.
  • Udías, José Manuel
  • Guerra, Pedro
Proceedings of: 2011 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC). Valencia, Spain, 23-29 October 2011, PET detector modules that implement depth of interaction information reduce uncertainties about the actual line-of-response after positron annihilation. This, in turn, has an effect in the spatial resolution and uniformity across the field of view of the reconstructed image. It also has an effect on the system sensitivity since it enables the use of thicker crystal with respect to a non-DOI system without deteriorating significantly the spatial resolution. In this work we evaluate a DOI detector design based on a scintillator phoswich of two types of pixelated crystals with different time decay constants. A matrix of silicon phomultipliers (SiPM) was coupled to this crystal array without any light-guide, and its outputs were connected to an anger logic type of charge divider which outputs were buffered using a transimpedance amplifier. These position signals were digitized using charge-to-digital converters, and the time decay constant of the crystal of interaction was measured using a delayed charge method. Previous works reported in the literature have demonstrated that this scheme for DOI PET detectors produce very good results in terms of spatial and energy resolution; however, the replacement of PMT with a SiPM matrix introduces some uncertainties that required further study. SiPM have demonstrated their good imaging capabilities when used with pixelated crystal scintillators, and their good timing performance allow us to predict that the DOI resolution was not going to be a problem with this technology. In this work we present quantitative results that assess the goodness of these detectors for its use on small-animal PET scanners., This work was supported in part by the CENIT-AMIT Ingenio 2010, TEC2008-06715 (Ministerio de Ciencia e Innovacion) RETIC-RECAVA (Ministerio de Sanidad y Consumo) ARTEMIS S2009/DPI-1802 (Comunidad de Madrid), and EU-FP7, FMT-XCT-201792., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Helical Optical Projection Tomography

  • Arranz, Alicia
  • Dong, Di
  • Zhu, Shouping
  • Rudin, Markus
  • Tsatsanis, Christos
  • Tian, Jie
  • Ripoll Lorenzo, Jorge
A new technique termed Helical Optical Projection Tomography (hOPT) has been developed with the aim to overcome some of the limitations of current 3D optical imaging techniques. hOPT is based on Optical Projection Tomography (OPT) with the major difference that there is a translation of the sample in the vertical direction during the image acquisition process, requiring a new approach to image reconstruction. Contrary to OPT, hOPT makes possible to obtain 3D-optical images of intact long samples without imposing limits on the sample length. This has been tested using hOPT to image long murine tissue samples such as spinal cords and large intestines. Moreover, 3D-reconstructed images of the colon of DSS-treated mice, a model for Inflammatory Bowel Disease, allowed the identification of the structural alterations. Finally, the geometry of the hOPT device facilitates the addition of a Selective Plane Illumination Microscopy (SPIM) arm, providing the possibility of delivering high resolution images of selected areas together with complete volumetric information, This work was partially supported by EC FP7 collaborative grant FMT-XCT and the Bill and Melinda Gates foundation. A.A. wishes to acknowledge support from Marie Curie IEF-2010-275137. J.R. wishes to acknowledge support from EC FP7 IMI project PREDICT-TB, and the EC FP7 CIG grant HIGH-THROUGHPUT TOMO. D.D., S.Z. and J.T. acknowledge support from the National Basic Research Program of China (973 Program) under Grant 2011CB707700, the Fellowship for Young International Scientists of the Chinese Academy of Sciences under Grant 2010Y2GA03, the National Natural Science Foundation of China under Grant 81101084 and Instrument Developing Project of the Chinese Academy of Sciences under Grant No. YZ201164, Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Corrección de atenuación de imágenes PET usando datos de TAC en el escáner para animales pequeños Argus PET/CT

  • Vicente, Esther
  • Udías, Ángel
  • López Herraiz, Joaquín
  • Udías, José Manuel
  • Desco Menéndez, Manuel
  • Vaquero López, Juan José
Actas de: XXVIII Congreso Anual de la Sociedad Española de Ingeniería Biomédica (CASEIB 2010). Madrid, 24-26 de noviembre de 2010., Existen diversos efectos físicos que degradan la calidad de la imagen PET, como por ejemplo la atenuación que sufren los fotones al atravesar el cuerpo en estudio. Este efecto reduce el número de fotones detectados, pero puede corregirse si se dispone de información anatómica del objeto. En este trabajo se describe la corrección de atenuación basada en una imagen TAC para el escáner de animales pequeños Argus PET/CT con imágenes PET reconstruidas con el algoritmo iterativo 3DOSEM., Este trabajo ha sido financiado en parte por el MEC (FPA2007-62216), la UCM (Grupos UCM, 910059), el CPAN (Consolider-Ingenio 2010, CSPD-2007-00042), la red RECAVA-RETIC el proyecto ARTEMIS (S2009/DPI-1802, Fondo Europeo de Desarrollo Regional), el proyecto ENTEPRASE (PSE-300000-2009-5, MICINN. España), por los proyectos del Ministerio de Ciencia e Innovación, TEC2007-64731, TEC 2008-06715-C02-1, la RETIC-RECAVA del Ministerio de Sanidad y Consumo, y el proyecto EU FP7 FMT-XCT-201792., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

An automatic method to select a noise threshold in the singular-value domain for reconstrucion of parallel plate non-contact FDOT images

  • Chamorro Servent, Judit
  • Aguirre, Juan
  • Ripoll Lorenzo, Jorge
  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
[Poster] 4th European Molecular Imaging Meeting, Barcelona, Spain, May 27 - 30, 2009, This work is supported in part by fundación Caja navarra (#12180), Ministerio de Ciencia e innovación (TeC2008-06715 and TeC2007-64731) and EU-FP7 project FMTXCT-201792, Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Fluorescence diffuse optical tomography using the split Bregman method

  • Abascal, Juan
  • Aguirre, Juan
  • Correia, Teresa
  • Chamorro Servent, Judit
  • Arridge, Simon
  • Ripoll Lorenzo, Jorge
  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
Purpose: Standard image reconstruction methods for fluorescence Diffuse Optical Tomography (fDOT) generally make use of L2-regularization. A better choice is to replace the L2 by a total variation functional that effectively removes noise while preserving edges. Among the wide range of approaches available, the recently appeared Split Bregman method has been shown to be optimal and efficient. Furthermore, additional constraints can be easily included. We propose the use of the Split Bregman method to solve the image reconstruction problem for fDOT with a nonnegativity constraint that imposes the reconstructed concentration of fluorophore to be positive. Methods: The proposed method is tested with simulated and experimental data, and results are compared with those yielded by an equivalent unconstrained optimization approach based on Gauss Newton (GN) method, in which the negative part of the solution is projected to zero after each iteration. In addition, the method dependence on the parameters that weigh data fidelity and nonnegativity constraints is analyzed. Results: Split Bregman yielded a reduction of the solution error norm and a better full width at tenth maximum for simulated data, and higher signal-to-noise ratio for experimental data. It is also shown that it led to an optimum solution independently of the data fidelity parameter, as long as the number of iterations is properly selected, and that there is a linear relation between the number of iterations and the inverse of the data fidelity parameter. Conclusions: Split Bregman allows the addition of a nonnegativity constraint leading to improve image quality., This study was supported by Ministerio de Ciencia e Innovación (FPI program, TEC 2007-64731, TEC 2008- 06715, and CENIT AMIT CEN-20101014), Comunidad de Madrid and European Regional Development Fund ARTEMIS S2009/DPI-1802, and EU-FP7 project FMTXCT- 201792., Publicado
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Contribución de congreso (ConferenceOutput)

Investigation of Different Compressed Sensing Approaches for Respiratory Gating in Small Animal CT

  • Pérez-Juste Abascal, Juan Felipe
  • Vaquero López, Juan José
  • Desco Menéndez, Manuel
  • Abella García, Mónica
  • Sisniega, Alejandro
  • Chavarrías, Cristina
Proceedings of: 2012 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC). Anaheim, California, USA. October 29 - November 3, 2012, Respiratory gating is necessary in cardio-thoracic small-animal imaging because of the physiological motions that are present during scanning. When applying a low-dose protocol, fewer than 180 noisy projections may be left for the reconstruction of each respiratory phase, leading to streaking artifacts. The Prior Image Constrained Compressed Sensing (PICCS) algorithm enables accurate reconstruction of highly undersampled data when a prior image is available. The gradient domain is the preferred choice for enforcing the sparsity of the variation of each phase with respect to the prior. We evaluate three CS algorithms based on the Split-Bregman approach, with different transformations of the prior penalty function: Gradient (TV-PICCS), L1-norm (L1-PICCS), and Wavelet Transform (WT-PICCS), on low-dose data acquired on a micro-CT scanner. High-dose projection data, acquired with a cone-beam micro-CT scanner, were arranged into four gates using a software-based retrospective gating and reconstructed with an FDK algorithm. To simulate the low-dose case, we took 120 projections from each gate and added Poisson noise. Prior image was obtained by the addition of all low-dose gates with Gaussian filtering. All CS methods performed very similarly in terms of noise and resolution, greatly improving FBP (79 % noise reduction) and eliminating streaks. Pixel and wavelet domains were found to be sparser than the commonly used gradient domain. In conclusion, compressed sensing using a Split-Bregman methodology is a feasible approach to reduce dose in CT respiratory gating. The selection of the sparsity transform for the prior term does not affect resolution and noise performance but it has an influence on the final image texture: Wavelet transform showed a more natural pattern than TV and L1-norm., This work was supported in part by projects TEC2008-06715 and TEC2007-64731 (Ministerio de Ciencia e innovacion), EU-FP7 FMTXCT-201792, ARTEMIS S2009/DPI-1802 (Comunidad de Madrid), and European Regional Development Funds (FEDER) and CDTI under the CENIT program (AMIT project, CEN- 20101014)., Publicado