Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Order and defectivity nanometrology by image processing and analysis of sub-20 nm BCPs features for lithographic applications

  • Simao, Claudia
  • Tuchapsky, D.
  • Khunsin, W.
  • Amann, A.
  • Morris, Michael A.
  • Sotomayor Torres, C. M.
Trabajo presentado al III Dimensional Optical Metrology and Inspection for Practical Applications, celebrado en Baltimore (US) del 5 al 6 de mayo de 2014., The line patterns obtained by the self-assembly of the block copolymer (BCP) polystyrene-b-polyethylene oxide (PS-b-PEO) was investigated. The hexagonal PS-b-PEO 42k-11.5k in a thin film was solvent annealed in a chlorophorm saturated atmosphere for three different annealing times. The microphase segregation of this BCP returned 18nm cylinders of PEO through the PS matrix, with an approximately 40 n periodicity, as expected. Under chlorophorm vapours, the PEO cylinders oriented perpendicular to the silicon substrate while increasing the annealing time. These cylinders formed linear patterns with different alignment. To achieve insights about the percentage of alignment, defect type pareto and density, and order quantification to compare the three annealing recipes, the samples were analysed with innovative image analysis software specifically developed in our laboratory to identify elements and defects of line arrays from block copolymer self-assembly. From this technique, it was extracted dimensional metrology estimating pitch size and placement error, and the line-width of the lines was estimated. Secondly, the methodology allows identification and quantification of typical defects observable in BCP systems, such as turning points, disclination or branching points, break or lone points and end points. The defect density and the quantification of the alignment were estimated using our technique. The methodology presented here represents a step forward in dimensional metrology and defect analysis of BCP DSA systems and can be readily used to analyze other lithographic or non-lithographic patterns., The research leading to these results received funding from the European Union FP7 under the project LAMAND (grant agreement n° 245565), MERGING (grant agreement no. 309150) and QUANTIHEAT (grant agreement no. 604668), and the Spanish MINECO under the project TAPHOR (contract nr. MAT2012-31392) and the Science Foundation Ireland under grant number 09/SIRG/I1615., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning thermal transport in ultrathin silicon membranes by surface nanoscale engineering

  • Neogi, Sanghamitra
  • Reparaz, J. S.
  • Pereira, Luiz Felipe C.
  • Graczykowski, Bartlomiej
  • Wagner, M. R.
  • Sledzinska, Marianna
  • Shchepetov, A.
  • Prunnila, M.
  • Ahopelto, Jouni
  • Sotomayor Torres, C. M.
  • Donadio, Davide
ACS AuthorChoice - This is an open access article published under an ACS AuthorChoice License, which permits copying and redistribution of the article or any adaptations for non-commercial purposes., A detailed understanding of the connections of fabrication and processing to structural and thermal properties of low-dimensional nanostructures is essential to design materials and devices for phononics, nanoscale thermal management, and thermoelectric applications. Silicon provides an ideal platform to study the relations between structure and heat transport since its thermal conductivity can be tuned over 2 orders of magnitude by nanostructuring. Combining realistic atomistic modeling and experiments, we unravel the origin of the thermal conductivity reduction in ultrathin suspended silicon membranes, down to a thickness of 4 nm. Heat transport is mostly controlled by surface scattering: rough layers of native oxide at surfaces limit the mean free path of thermal phonons below 100 nm. Removing the oxide layers by chemical processing allows us to tune the thermal conductivity over 1 order of magnitude. Our results guide materials design for future phononic applications, setting the length scale at which nanostructuring affects thermal phonons most effectively., This work is partly funded by the European Commission FP7-ENERGY-FET project MERGING, NMP QUANTIHEAT and ICT NANOTHERM, with Grant Agreement Nrs: 309150, 604668 and 318117, respectively. S.N. and D.D. acknowledge financial support from MPG under the MPRG program. J.S.R., M.R.W., and C.M.S.T. acknowledge support form the Spanish MINECO projects TAPHOR (MAT-2012-31392) and nanoTHERM (CONSOLIDER CSD2010-00044). M.R.W. acknowledges support of the Marie Curie Postdoctoral Fellowship HeatProNano (Grant No. 628197). M.P. and A.S. acknowledge funding from the Academy of Finland (Grant No. 252598)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Titanium particle incorporation in block copolymer templates

  • Kreuzer, Martin
  • Simao, Claudia
  • Díaz, Ana
  • Sotomayor Torres, C. M.
Template-directed formation of titanium structures on block copolymer templates has been recently reported [1]. Here, the incorporation of titanium in a thin film template is studied. We show that the surface free energy contrast in microphase-separated polystyrene-block-polyethylene oxide templates is not limited to the template film surface, but directs the assembly of titanium atoms in the template thin film. The details of the self-assembly of titanium particles on the block copolymer nanostructured surface and inside the 3D film structure are studied with selected amounts of titanium. Evaporated titanium preferentially wets the polystyrene block of the block copolymer film and diffuses inside the film, conserving the block copolymer nanostructure. Increasing deposition leads to the formation of a mesoporous titanium layer on the block copolymer film, which reproduces that of the underlying template, in this particular case with a thickness of 12 nm and a periodic pore-to-pore distance of 35 nm. The formation of a mesoporous titanium layer prevents from further titanium diffusion inside the block copolymer film. The combination of the X-ray scattering techniques presented here provides sufficient sensitivity to follow the titanium formation in the three dimensional network of the block copolymer films., The authors acknowledge the financial support from the European Commission FP7 for the Integrated Infrastructure Initiative N. 262348 European Soft Matter (ESMI) and projects LAMAND (GA No. 245565), QUANTIHEAT (GA No. 604668) and MERGING (GA No. 309150). The Spanish MINECO project TAPHOR (MAT2012–31392) and the Deutsche Forschungsgemeinschaft (Grant No. KR 4522/1-1) are also acknowledged. The work at ICN2 is partially supported by the Spanish MINECO Severo Ochoa Centres of Excellence (SEV-2013-0295)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal conductivity of MoS2 polycrystalline nanomembranes

  • Sledzinska, Marianna
  • Graczykowski, Bartlomiej
  • Sachat, Alexandros el
  • Reparaz, J. S.
  • Alzina, Francesc
  • Colombo, Luciano
  • Roche, Stephan
  • Sotomayor Torres, C. M.
arXiv:1604.04865.-- et al., Heat conduction in 2D materials can be effectively engineered by means of controlling nanoscale grain structure. Afavorable thermal performance makes these structures excellent candidates for integrated heat management units. Here we show combined experimental and theoretical studies for MoS nanosheets in a nanoscale grain-size limit.Wereport thermal conductivity measurements on 5 nm thick polycrystalline MoS by means of 2-laser Raman thermometry. The free-standing, drum-like MoS nanomembranes were fabricated using a novel polymer- and residue-free, wet transfer, in which we took advantage of the difference in the surface energies between MoS and the growth substrate to transfer the CVD-grown nanosheets. The measurements revealed a strong reduction in the in-plane thermal conductivity down to about 0.73 ± 0.25 W m K. The results are discussed theoretically using finite elements method simulations for a polycrystalline film, and a scaling trend of the thermally conductivity with grain size is proposed., The authors acknowledge the financial support from the FP7 projects MERGING (Grant No. 309150) and QUANTIHEAT (No. 604668); the Spanish MICINN project PHENTOM (FIS2015-70862-P); and the program Severo Ochoa (Grant SEV-2013-0295). SR acknowledges funding from the Spanish Ministry of Economy and Competitiveness and the European Regional Development Fund (FIS2015-67767-P (MINECO/FEDER)); and MP acknowledges the program Juan de la Cierva (FPDI-2013-18968)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Two-dimensional phononic crystals: Disorder matters

  • Wagner, M. R.
  • Graczykowski, Bartlomiej
  • Reparaz, J. S.
  • Sachat, Alexandros el
  • Sledzinska, Marianna
  • Alzina, Francesc
  • Sotomayor Torres, C. M.
The design and fabrication of phononic crystals (PnCs) hold the key to control the propagation of heat and sound at the nanoscale. However, there is a lack of experimental studies addressing the impact of order/disorder on the phononic properties of PnCs. Here, we present a comparative investigation of the influence of disorder on the hypersonic and thermal properties of two-dimensional PnCs. PnCs of ordered and disordered lattices are fabricated of circular holes with equal filling fractions in free-standing Si membranes. Ultrafast pump and probe spectroscopy (asynchronous optical sampling) and Raman thermometry based on a novel two-laser approach are used to study the phononic properties in the gigahertz (GHz) and terahertz (THz) regime, respectively. Finite element method simulations of the phonon dispersion relation and three-dimensional displacement fields furthermore enable the unique identification of the different hypersonic vibrations. The increase of surface roughness and the introduction of short-range disorder are shown to modify the phonon dispersion and phonon coherence in the hypersonic (GHz) range without affecting the room-temperature thermal conductivity. On the basis of these findings, we suggest a criteria for predicting phonon coherence as a function of roughness and disorder., The authors acknowledge financial support from the EU FP7 project MERGING (Grant 309150), NANO-RF (Grant 318352), and QUANTIHEAT (Grant 604668); the Spanish MICINN projects nanoTHERM (Grant CSD2010-0044) and PHENTOM (FIS2015-70862-P); and the Severo Ochoa Program (MINECO, Grant SEV-2013-0295). M.R.W. acknowledges the postdoctoral Marie Curie Fellowship (IEF) HeatProNano (Grant 628197)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Thermal conductivity and air-mediated losses in periodic porous silicon membranes at high temperatures

  • Graczykowski, Bartlomiej
  • Sachat, Alexandros el
  • Reparaz, J. S.
  • Sledzinska, Marianna
  • Wagner, M. R.
  • Chávez-Angel, Emigdio
  • Volz, Sebastian
  • Alzina, Francesc
  • Sotomayor Torres, C. M.
Resumen del trabajo presentado a la NanoTech Poland International Conference and Exhibition, celebrada en Poznán (Polonia) del 1 al 3 de junio de 2017., Progress in the last few decades in nano-scale thermal transport has enabled a significant degree of control over heat and sound propagation by lattice vibrations - phonons. The latest investigations on the thermal properties of silicon, the most common material in electronics, micro- and nano-electro-mechanical systems (MEMS and NEMS) and photonics, have pointed to nanostructuring as a highly efficient approach to acoustic phonon engineering. Heat conduction in silicon can be effectively engineered by means of submicrometer porous thin free-standing membranes. Tunable thermal properties make these structures good candidates for integrated heat management units such as waste heat recovery, rectification or efficient heat dissipation. However, possible applications require detailed thermal characterization at high temperatures which, up to now, has been an experimental challenge. In this work we use the contactless two-laser Raman thermometry to study heat dissipation in periodic porous membranes at high temperatures via lattice conduction and air-mediated losses. We find the reduction of the thermal conductivity and its temperature dependence closely correlated with the structure feature size. Based on two-phonon Raman spectra, we attribute this behavior to diffuse (incoherent) phononboundary scattering. Furthermore, we investigate and quantify the heat dissipation via natural air-mediated cooling, which can be tuned by engineering the porosity., The authors acknowledge the financial support from the FP7 project MERGING (Grant No. 309150) and QUANTIHEAT (Grant No 604668); the Spanish MINECO projects nanoTHERM (Grant No. CSD2010- 595 0044) and PHENTOM (FIS2015-70862-P) and the program Severo Ochoa (Grant SEV-2013-0295). B.G. acknowledges the support from the Homing Programme (Homing/2016-1/2) granted by the Foundation for Polish Science., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Impact of the regularization parameter in the mean free path reconstruction method: Nanoscale heat transport and beyond

  • Sanchez-Martinez, Miguel-Ángel
  • Alzina, Francesc
  • Oyarzo, Juan
  • Sotomayor Torres, C. M.
  • Chávez-Angel, Emigdio
The understanding of the mean free path (MFP) distribution of the energy carriers in materials (e.g., electrons, phonons, magnons, etc.) provides a key physical insight into their transport properties. In this context, MFP spectroscopy has become an important tool to describe the contribution of carriers with different MFP to the total transport phenomenon. In this work, we revise the MFP reconstruction technique and present a study on the impact of the regularization parameter on the MFP distribution of the energy carriers. By using the L-curve criterion, we calculate the optimal mathematical value of the regularization parameter. The effect of the change from the optimal value in the MFP distribution is analyzed in three case studies of heat transport by phonons. These results demonstrate that the choice of the regularization parameter has a large impact on the physical information obtained from the reconstructed accumulation function, and thus cannot be chosen arbitrarily. The approach can be applied to various transport phenomena at the nanoscale involving carriers of different physical nature and behavior., This research was funded by the EU FP7 project QUANTIHEAT (Grant No 604668) and the Spanish MINECO-Feder project PHENTOM (FIS2015-70862-P). M.-Á.S.-M. acknowledges support from SO-FPI fellowship BES 2015-075920. ICN2 acknowledges support from Severo Ochoa Program (MINECO, Grant SEV-2017-0706) and funding from the CERCA Programme/Generalitat de Catalunya., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

In-line metrology for roll-to-roll UV assisted nanoimprint lithography using diffractometry

  • Kreuzer, Martin
  • Whitworth, Guy L.
  • Francone, Achille
  • Gomis-Bresco, J.
  • Kehagias, N.
  • Sotomayor Torres, C. M.
We describe and discuss the optical design of a diffractometer to carry out in-line quality control during roll-to-roll nanoimprinting. The tool measures diffractograms in reflection geometry, through an aspheric lens to gain fast, non-invasive information of any changes to the critical dimensions of target grating structures. A stepwise tapered linear grating with constant period was fabricated in order to detect the variation in grating linewidth through diffractometry. The minimum feature change detected was ∼40 nm to a precision of 10 nm. The diffractometer was then integrated with a roll-to-roll UV assisted nanoimprint lithography machine to gain dynamic measurements in situ., The authors acknowledge the financial support from the EU projects, FLEXPOL (No. H2020- NMBP-PILOT-2016-721062), FP7 QUANTIHEAT (No. FP7-NMP-2013-LARGE-7-604668), as well as the MINECO Project PHENTOM (No. FIS2015-70862-P). M.K. acknowledges financial support from the Deutsche Forschungsgemeinschaft (No. KR 4522/1-1). The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa programme of the Spanish Ministry of Economy, Industry and Competitiveness (MINECO, Grant No. SEV-2013-0295)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crossover from ballistic to diffusive thermal transport in suspended graphene membranes

  • Sachat, Alexandros el
  • Köneman, F.
  • Menges, F.
  • Del Corro, Elena
  • Garrido, Jose A.
  • Sotomayor Torres, C. M.
  • Alzina, Francesc
  • Gotsmann, B.
We report heat transport measurements on suspended single-layer graphene disks with radius of 150–1600 nm using a high-vacuum scanning thermal microscope. The results of this study revealed a radius-dependent thermal contact resistance between tip and graphene, with values between 1.15 and 1.52  ×  108 KW−1. The observed scaling of thermal resistance with radius is interpreted in terms of ballistic phonon transport in suspended graphene discs with radius smaller than 775 nm. In larger suspended graphene discs (radius  >775 nm), the thermal resistance increases with radius, which is attributed to in-plane heat transport being limited by phonon–phonon resistive scattering processes, which resulted in a transition from ballistic to diffusive thermal transport. In addition, by simultaneously mapping topography and steady-state heat flux signals between a self-heated scanning probe sensor and graphene with 17 nm thermal spatial resolution, we demonstrated that the surface quality of the suspended graphene and its connectivity with the Si/SiO2 substrate play a determining role in thermal transport. Our approach allows the investigation of heat transport in suspended graphene at sub-micrometre length scales and overcomes major limitations of conventional experimental methods usually caused by extrinsic thermal contact resistances, assumptions on the value of the graphene's optical absorbance and limited thermal spatial resolution., AE, FA and CMST acknowledge financial support from the FP7 project QUANTIHEAT (No. 604668) and the Spanish MICINN project PHENTOM (FIS2015-70862-P). ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grants No. SEV-2013-0295 and No. SEV-2017-0706) and by the CERCA programme/Generalitat de Catalunya. FK and BG acknowledge funding in through the H2020 European project CONNECT under the grant agreement number 688612 (www.connect-h2020.eu). FM acknowledges support by The Branco Weiss Fellowship–Society in Science administered by the ETH Zurich., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Quantifying thermal transport in buried semiconductor nanostructures via cross-sectional scanning thermal microscopy

  • Spièce, Jean
  • Evangeli, Charalambos
  • Robson, Alexander James
  • Sachat, Alexandros el
  • Haenel, Linda
  • Alonso Carmona, M. Isabel
  • Garriga Bacardi, Miquel
  • Robinson, Benjamin J.
  • Oehme, Michael
  • Schulze, Jörg
  • Alzina, Francesc
  • Sotomayor Torres, C. M.
  • Kolosov, Oleg V.
Managing thermal transport in nanostructures became a major challenge in the development of active microelectronic, optoelectronic and thermoelectric devices, stalling the famous Moore's law of clock speed increase of microprocessors for more than a decade. To find the solution to this and linked problems, one needs to quantify the ability of these nanostructures to conduct heat with adequate precision, nanoscale resolution, and, essentially, for the internal layers buried in the 3D structure of modern semiconductor devices. Existing thermoreflectance measurements and “hot wire” 3ω methods cannot be effectively used at lateral dimensions of a layer below a micrometre; moreover, they are sensitive mainly to the surface layers of a relatively high thickness of above 100 nm. Scanning thermal microscopy (SThM), while providing the required lateral resolution, provides mainly qualitative data of the layer conductance due to undefined tip–surface and interlayer contact resistances. In this study, we used cross-sectional SThM (xSThM), a new method combining scanning probe microscopy compatible Ar-ion beam exit nano-cross-sectioning (BEXP) and SThM, to quantify thermal conductance in complex multilayer nanostructures and to measure local thermal conductivity of oxide and semiconductor materials, such as SiO2, SiGex and GeSny. By using the new method that provides 10 nm thickness and few tens of nm lateral resolution, we pinpoint crystalline defects in SiGe/GeSn optoelectronic materials by measuring nanoscale thermal transport and quantifying thermal conductivity and interfacial thermal resistance in thin spin-on materials used in extreme ultraviolet lithography (eUV) fabrication processing. The new capability of xSThM demonstrated here for the first time is poised to provide vital insights into thermal transport in advanced nanoscale materials and devices., The authors acknowledge the EU QUANTIHEAT FP7 project no. 604668 and the Horizon 2020 Graphene Flagship Core 3 project no. 881603, EPSRC EP/G015570/1 EP/K023373/1, EP/G06556X/1. EP/V00767X/1 and EP/P006973/1 and Faraday Institution NEXGENNA project for the overall support, and Paul Instrument Fund, c/o The Royal Society grant on “Infrared non-contact atomic force microscopy (ncAFM-IR)” for the equipment support. We are also grateful to our industrial collaborators Leica Microsystems, Lancaster Materials Analysis Ltd and Bruker for the financial and instrumentation support. LTD to ICN2 is supported by the Spanish MINECO (Severo Ochoa Centers of Excellence Program under Grant SEV-2017-0706 and CEX2019-000917-S) and by the Generalitat de Catalunya (Grants 2017SGR806, 2017SGR488, and the CERCA Program). We thank Severine Gomès from CNRS and Harry Hoster from Lancaster Energy for the helpful discussions on the measurements, and Andy Cockburn and Mike Kocsic from IMEC for the interesting materials and discussion of applications., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanoscale Mapping of Thermal and Mechanical Properties of Bare and Metal-Covered Self-Assembled Block Copolymer Thin Films

  • Sachat, Alexandros el
  • Spièce, Jean
  • Evangeli, Charalambos
  • Robson, Alexander James
  • Kreuzer, Martin
  • Rodríguez-Laguna, María del Rocío
  • Chávez-Angel, Emigdio
  • Sledzinska, Marianna
  • Sotomayor Torres, C. M.
  • Kolosov, Oleg V.
  • Alzina, Francesc
We report on the structural, mechanical, and thermal analysis of 40 nm thick polystyrene-block-poly(ethylene oxide) (PS-b-PEO) block copolymer (BCP) films coated with evaporated chromium layers of different thicknesses (1, 2, and 5 nm). Solvent annealing processes allow the structural control of the BCP films morphology by rearranging the position of the PEO cylinders parallel to the substrate plane. High-vacuum scanning thermal microscopy and ultrasonic force microscopy measurements performed in ambient pressure revealed that coated ultrathin metal layers strongly influence the heat dissipation in the BCP films and the local surface stiffness of the individual BCP domains, respectively. The measured tip-sample effective thermal resistance decreases from 6.1 × 107 to 2.5 × 107 K W-1 with increasing Cr film thickness. In addition, scanning probe microscopy measurements allow the thermal and mechanical mapping of the two segregated polymer domains (PEO-PS) of sub-50 nm characteristic sizes, with sub-10 nm thermal spatial resolution. The results revealed the effect of the surface morphology of the BCP and the incorporation of the metal film on the nanoscale thermal properties and volume self-assembly on the mechanical properties. The findings from this study provide insight into the formation of high aspect ratio BCP-metal structures with the more established applications in lithography. In addition, knowledge of the thermal and mechanical properties at the nanoscale is required in emergent applications, where BCPs, or polymers in general, are part of the structure or device. The performance of such devices is commonly related to the requirement of increased heat dissipation while maintaining mechanical flexibility., The authors acknowledge the financial support from the EU FP7 project QUANTIHEAT (Grant No. 604668) and The Royal Society Paul Instrument Fund, EPSRC Grant EP/K023373/1. ICN2 is supported by Spanish MINECO (Severo Ochoa Centers of Excellence Program under Grant SEV-2017-0706 and PHENTOM project under Grant FIS2015-70862-P) and by the Generalitat de Catalunya (Grant 2017SGR806 and the CERCA Program), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Local Heat Dissipation and Elasticity of Suspended Silicon Nanowires Revealed by Dual Scanning Electron and Thermal Microscopies

  • Sojo-Gordillo, Jose M
  • Gadea-Diez, Gerard
  • Renahy, David
  • Salleras, Marc
  • Duque-Sierra, Carolina
  • Vincent, Pascal
  • Fonseca, Luis
  • Chapuis, Pierre-Olivier
  • Morata, Alex
  • Gomès, Séverine
  • Tarancón, Albert
A novel combined setup, with a scanning thermal microscope (SThM) embedded in a scanning electron microscope (SEM), is used to characterize a suspended silicon rough nanowire (NW), which is epitaxially clamped at both sides and therefore monolithically integrated in a microfabricated device. The rough nature of the NW surface, which prohibits vacuum-SThM due to loose contact for heat dissipation, is circumvented by decorating the NW with periodic platinum dots. Reproducible approaches over these dots, enabled by the live feedback image provided by the SEM, yield a strong improvement in thermal contact resistance and a higher accuracy in its estimation. The results-thermal resistance at the tip-sample contact of 188±3.7K µW-1 and thermal conductivity of the NW of 13.7±1.6W m-1 K-1-are obtained by performing a series of approach curves on the dots. Noteworthy, the technique allows measuring elastic properties at the same time-the moment of inertia of the NW is found to be (6.1±1.0) × 10-30m4-which permits to correlate the respective effects of the rough shell on heat dissipation and on the NW stiffness. The work highlights the capabilities of the dual SThM/SEM instrument, in particular the interest of systematic approach curves with well-positioned and monitored tip motion., This investigation has been supported by the Spanish Ministry of Education through the FPU grant , and by the University and Research Secretary of the Business and Knowledge Department of the Generalitat de Catalonia in the project FEM‐IoT (). This research as also been supported by the Spanish National Research Agency (AEi) though the project (AEI/FEDER, EU) . This research has used the Spanish ICTS Network , partially funded by FEDER funds through project . This work has also been supported by the French National Research Agency (ANR) through the projects and the project (LabEx iMUST). The European Commission also supported this investigation through the project (GA 766853) and the project (GA 604668). FPU18/01494 001‐P‐001662 PID2019‐110142RB‐C21 THERMOLOGICS MICRONANOFABS MINATEC‐PLUS‐2 FICTS2019‐02‐40 TIPTOP ANR‐16‐CE09‐0023 ATTSEM ANR‐10‐LABX‐0064 EFINED H2020‐FETOPEN‐2016‐2017 QUANTIHEAT NMP‐2013‐LARGE‐7, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Using oxides to compute with heat

  • Nataf, Guillaume F.
  • Volz, Sebastian
  • Ordonez Miranda, Jose
  • Íñiguez, Jorge
  • Rurali, Riccardo
  • Dkhil, Brahim
One of the most innovative possibilities offered by oxides is the use of heat currents for computational purposes. Towards this goal, phase-change oxides, including ferroelectrics, ferromagnets and related materials, could reproduce sources, logic units and memories used in current and future computing schemes., This Comment was cofunded by the European Union (European Research Council (ERC), DYNAMHEAT, No. 101077402; European Program FP7-NMP-LARGE-7, QUANTIHEAT, No. 604668). Views and opinions expressed are, however, those of the authors only and do not necessarily reflect those of the European Union or the ERC. J.Í.-G. acknowledges the funding of the Luxembourg National Research Fund (FNR) through Grant C21/MS/15799044/FERRODYNAMICS. R.R. acknowledges financial support by MCIN/AEI/10.13039/501100011033 under grant PID2020–119777GB-I00, and the Severo Ochoa Centres of Excellence Program under grant CEX2019–000917-S, and by the Generalitat de Catalunya under grant 2021 SGR 01519., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Lead-free room-temperature ferroelectric thermal conductivity switch using anisotropies in thermal conductivities

  • Féger, Lucile
  • Escorihuela Sayalero, Carlos
  • Rampnoux, Jean-Michel
  • Kontou, Kyriaki
  • Bah, Micka
  • Íñiguez, Jorge
  • Cazorla, Claudio
  • Monot-Laffez, Isabelle
  • Douri, Sarah
  • Grauby, Stéphane
  • Rurali, Riccardo
  • Dilhaire, Stefan
  • Gomès, Séverine
  • Nataf, Guillaume F.
Materials with on-demand control of thermal conductivity are the prerequisites to build thermal conductivity switches, where the thermal conductivity can be turned ON and OFF. However, the ideal switch, while required to develop novel approaches to solid-state refrigeration, energy harvesting, and even phononic circuits, is still missing. It should consist of an active material only, be environment friendly, and operate near room temperature with a reversible, fast, and large switching ratio. Here, we first predict by ab initio electronic structure calculations that ferroelectric domains in barium titanate exhibit anisotropic thermal conductivities. We confirm this prediction by combining frequency-domain thermoreflectance and scanning thermal microscopy measurements on a single crystal of barium titanate. We then use this gained knowledge to propose a lead-free thermal conductivity switch without inactive material, operating reversibly with an electric field. At room temperature, we find a switching ratio of 1.6 $\pm$ 0.3, exceeding the performances of state-of-the-art materials suggested for thermal conductivity switches., We thank F. Barcella, R. Doineau, and B. Negulescu for technical support for aluminum sputtering. We thank J. C. A. Abanto for technical support for developing 3D simulation for SThM measurement post-treatment. This paper was cofunded by the European Union [European Research Council (ERC), DYNAMHEAT, Grant No. 101077402; European Program FP7-NMP-LARGE-7, QUANTIHEAT, Grant No. 604668]. We acknowledge financial support by MCIN/AEI/10.13039/501100011033 under Grant No. PID2020-119777GB-I00, the “Ramón y Cajal” fellowship RYC2018-024947-I and the Severo Ochoa Centres of Excellence Program (CEX2019-000917-S), by the Generalitat de Catalunya (2021 SGR 01519), and by the Luxembourg National Research Fund (C21/MS/15799044/FERRODYNAMICS). Some of this work has been performed on the CERTeM (microelectronics technological research and development center) technological platform supported by French region Centre Val de Loire, Tours Metropolis and FEDER funds., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal conductivity of MoS2 polycrystalline nanomembranes

  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Placidi, Marcel
  • Saleta Reig, David|||0000-0003-3189-2331
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Alzina, Francesc|||0000-0002-7082-0624
  • Mortazavi, Bohayra|||0000-0003-3031-5057
  • Quey, Romain|||0000-0002-1593-8179
  • Colombo, Luciano|||0000-0001-5335-4652
  • Roche, Stephan|||0000-0003-0323-4665
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Heat conduction in 2D materials can be effectively engineered by means of controlling nanoscale grain structure. Afavorable thermal performance makes these structures excellent candidates for integrated heat management units. Here we show combined experimental and theoretical studies for MoS₂ nanosheets in a nanoscale grain-size limit.Wereport thermal conductivity measurements on 5 nm thick polycrystalline MoS₂ by means of 2-laser Raman thermometry. The free-standing, drum-like MoS₂ nanomembranes were fabricated using a novel polymer- and residue-free, wet transfer, in which we took advantage of the difference in the surface energies between MoS₂ and the growth substrate to transfer the CVD-grown nanosheets. The measurements revealed a strong reduction in the in-plane thermal conductivity down to about 0.73 ± 0.25 W m⁻¹ K⁻¹. The results are discussed theoretically using finite elements method simulations for a polycrystalline film, and a scaling trend of the thermally conductivity with grain size is proposed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal transport in epitaxial Si1-xGe x alloy nanowires with varying composition and morphology

  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Spiece, J.
  • Alonso Carmona, Maria Isabel|||0000-0001-7669-5871
  • Goñi, Alejandro|||0000-0002-1193-3063
  • Garriga, Miquel|||0000-0002-6683-0790
  • Vaccaro, Pablo Oscar
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Kolosov, O. V.
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Alzina, Francesc|||0000-0002-7082-0624
We report on structural, compositional, and thermal characterization of self-assembled in-plane epitaxial SiGe alloy nanowires grown by molecular beam epitaxy on Si (001) substrates. The thermal properties were studied by means of scanning thermal microscopy (SThM), while the microstructural characteristics, the spatial distribution of the elemental composition of the alloy nanowires and the sample surface were investigated by transmission electron microscopy and energy dispersive x-ray microanalysis. We provide new insights regarding the morphology of the in-plane nanostructures, their size-dependent gradient chemical composition, and the formation of a 5 nm thick wetting layer on the Si substrate surface. In addition, we directly probe heat transfer between a heated scanning probe sensor and SiGe alloy nanowires of different morphological characteristics and we quantify their thermal resistance variations. We correlate the variations of the thermal signal to the dependence of the heat spreading with the cross-sectional geometry of the nanowires using finite element method simulations. With this method we determine the thermal conductivity of the nanowires with values in the range of 2-3 W m K. These results provide valuable information in growth processes and show the great capability of the SThM technique in ambient environment for nanoscale thermal studies, otherwise not possible using conventional techniques.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

In-line metrology for roll-to-roll UV assisted nanoimprint lithography using diffractometry

  • Kreuzer, Martin|||0000-0002-7305-5016
  • Whitworth, Guy L.|||0000-0002-5060-6946
  • Francone, Achille|||0000-0001-7757-9901
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Kehagias, Nikolaos|||0000-0002-2698-383X
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We describe and discuss the optical design of a diffractometer to carry out in-line quality control during roll-to-roll nanoimprinting. The tool measures diffractograms in reflection geometry, through an aspheric lens to gain fast, non-invasive information of any changes to the critical dimensions of target grating structures. A stepwise tapered linear grating with constant period was fabricated in order to detect the variation in grating linewidth through diffractometry. The minimum feature change detected was ∼40 nm to a precision of 10 nm. The diffractometer was then integrated with a roll-to-roll UV assisted nanoimprint lithography machine to gain dynamic measurements in situ.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal conductivity and air-mediated losses in periodic porous silicon membranes at high temperatures

  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Wu, Yang|||0000-0002-0128-7280
  • Volz, Sebastian
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Heat conduction in silicon can be effectively engineered by means of sub-micrometre porous thin free-standing membranes. Tunable thermal properties make these structures good candidates for integrated heat management units such as waste heat recovery, rectification or efficient heat dissipation. However, possible applications require detailed thermal characterisation at high temperatures which, up to now, has been an experimental challenge. In this work we use the contactless two-laser Raman thermometry to study heat dissipation in periodic porous membranes at high temperatures via lattice conduction and air-mediated losses. We find the reduction of the thermal conductivity and its temperature dependence closely correlated with the structure feature size. On the basis of two-phonon Raman spectra, we attribute this behaviour to diffuse (incoherent) phonon-boundary scattering. Furthermore, we investigate and quantify the heat dissipation via natural air-mediated cooling, which can be tuned by engineering the porosity.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Impact of the regularization parameter in the mean free path reconstruction method, Nanoscale heat transport and beyond

  • Sanchez Martinez, Miguel Ángel
  • Alzina, Francesc|||0000-0002-7082-0624
  • Oyarzo, Juan
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
The understanding of the mean free path (MFP) distribution of the energy carriers in materials (e.g., electrons, phonons, magnons, etc.) provides a key physical insight into their transport properties. In this context, MFP spectroscopy has become an important tool to describe the contribution of carriers with different MFP to the total transport phenomenon. In this work, we revise the MFP reconstruction technique and present a study on the impact of the regularization parameter on the MFP distribution of the energy carriers. By using the L-curve criterion, we calculate the optimal mathematical value of the regularization parameter. The effect of the change from the optimal value in the MFP distribution is analyzed in three case studies of heat transport by phonons. These results demonstrate that the choice of the regularization parameter has a large impact on the physical information obtained from the reconstructed accumulation function, and thus cannot be chosen arbitrarily. The approach can be applied to various transport phenomena at the nanoscale involving carriers of different physical nature and behavior.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tuning Thermal Transport in Ultrathin Silicon Membranes by Surface Nanoscale Engineering

  • Neogi, Sanghamitra
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Pereira, Luiz Felipe C.
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Shchepetov, Andrey
  • Prunnila, Mika
  • Ahopelto, Jouni|||0000-0003-3372-6097
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Donadio, Davide|||0000-0002-2150-4182
A detailed understanding of the connections of fabrication and processing to structural and thermal properties of low-dimensional nanostructures is essential to design materials and devices for phononics, nanoscale thermal management, and thermoelectric applications. Silicon provides an ideal platform to study the relations between structure and heat transport since its thermal conductivity can be tuned over 2 orders of magnitude by nanostructuring. Combining realistic atomistic modeling and experiments, we unravel the origin of the thermal conductivity reduction in ultrathin suspended silicon membranes, down to a thickness of 4 nm. Heat transport is mostly controlled by surface scattering: rough layers of native oxide at surfaces limit the mean free path of thermal phonons below 100 nm. Removing the oxide layers by chemical processing allows us to tune the thermal conductivity over 1 order of magnitude. Our results guide materials design for future phononic applications, setting the length scale at which nanostructuring affects thermal phonons most effectively.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Record low thermal conductivity of polycrystalline MoS2 films, tuning the thermal conductivity by grain orientation

  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Quey, Romain|||0000-0002-1593-8179
  • Mortazavi, Bohayra|||0000-0003-3031-5057
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Placidi, M.
  • Saleta Reig, David|||0000-0003-3189-2331
  • Navarro Urrios, Daniel|||0000-0001-9055-1583
  • Alzina, Francesc|||0000-0002-7082-0624
  • Colombo, Luciano|||0000-0001-5335-4652
  • Roche, Stephan|||0000-0003-0323-4665
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We report a record low thermal conductivity in polycrystalline MoS obtained for ultrathin films with varying grain sizes and orientations. By optimizing the sulfurization parameters of nanometer-thick Mo layers, five MoS films containing a combination of horizontally and vertically oriented grains, with respect to the bulk (001) monocrystal, were grown. From transmission electron microscopy, the average grain size, typically below 10 nm, and proportion of differently oriented grains were extracted. The thermal conductivity of the suspended samples was extracted from a Raman laser-power-dependent study, and the lowest value of thermal conductivity of 0.27 W m K, which reaches a similar value as that of Teflon, is obtained in a polycrystalline sample formed by a combination of horizontally and vertically oriented grains in similar proportion. Analysis by means of molecular dynamics and finite element method simulations confirm that such a grain arrangement leads to lower grain boundary conductance. We discuss the possible use of these thermal insulating films in the context of electronics and thermoelectricity.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Two-Dimensional Phononic Crystals, Disorder Matters

  • Wagner, Markus R.|||0000-0002-7367-5629
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
The design and fabrication of phononic crystals (PnCs) hold the key to control the propagation of heat and sound at the nanoscale. However, there is a lack of experimental studies addressing the impact of order/disorder on the phononic properties of PnCs. Here, we present a comparative investigation of the influence of disorder on the hypersonic and thermal properties of two-dimensional PnCs. PnCs of ordered and disordered lattices are fabricated of circular holes with equal filling fractions in free-standing Si membranes. Ultrafast pump and probe spectroscopy (asynchronous optical sampling) and Raman thermometry based on a novel two-laser approach are used to study the phononic properties in the gigahertz (GHz) and terahertz (THz) regime, respectively. Finite element method simulations of the phonon dispersion relation and three-dimensional displacement fields furthermore enable the unique identification of the different hypersonic vibrations. The increase of surface roughness and the introduction of short-range disorder are shown to modify the phonon dispersion and phonon coherence in the hypersonic (GHz) range without affecting the room-temperature thermal conductivity. On the basis of these findings, we suggest a criteria for predicting phonon coherence as a function of roughness and disorder.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Crossover from ballistic to diffusive thermal transport in suspended graphene membranes

  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Köenemann, F.
  • Menges, F.
  • Del Corro, Elena|||0000-0001-6452-9139
  • Garrido, Jose|||0000-0001-5621-1067
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Alzina, Francesc|||0000-0002-7082-0624
  • Gotsmann, B.
We report heat transport measurements on suspended single-layer graphene disks with radius of 150-1600 nm using a high-vacuum scanning thermal microscope. The results of this study revealed a radius-dependent thermal contact resistance between tip and graphene, with values between 1.15 and 1.52 × 10 KW. The observed scaling of thermal resistance with radius is interpreted in terms of ballistic phonon transport in suspended graphene discs with radius smaller than 775 nm. In larger suspended graphene discs (radius.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Quantifying thermal transport in buried semiconductor nanostructures, Via cross-sectional scanning thermal microscopy

  • Spièce, Jean
  • Evangeli, Charalambos|||0000-0003-3867-8530
  • Robson, Alexander J.
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Haenel, Linda
  • Alonso, M. Isabel
  • Garriga, Miquel|||0000-0002-6683-0790
  • Robinson, Benjamin James|||0000-0001-8676-6469
  • Oehme, Michael|||0000-0002-1637-1338
  • Schulze, Jörg
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia
  • Kolosov, Oleg Victor|||0000-0003-3278-9643
Managing thermal transport in nanostructures became a major challenge in the development of active microelectronic, optoelectronic and thermoelectric devices, stalling the famous Moore's law of clock speed increase of microprocessors for more than a decade. To find the solution to this and linked problems, one needs to quantify the ability of these nanostructures to conduct heat with adequate precision, nanoscale resolution, and, essentially, for the internal layers buried in the 3D structure of modern semiconductor devices. Existing thermoreflectance measurements and "hot wire"3ω methods cannot be effectively used at lateral dimensions of a layer below a micrometre; moreover, they are sensitive mainly to the surface layers of a relatively high thickness of above 100 nm. Scanning thermal microscopy (SThM), while providing the required lateral resolution, provides mainly qualitative data of the layer conductance due to undefined tip-surface and interlayer contact resistances. In this study, we used cross-sectional SThM (xSThM), a new method combining scanning probe microscopy compatible Ar-ion beam exit nano-cross-sectioning (BEXP) and SThM, to quantify thermal conductance in complex multilayer nanostructures and to measure local thermal conductivity of oxide and semiconductor materials, such as SiO2, SiGex and GeSny. By using the new method that provides 10 nm thickness and few tens of nm lateral resolution, we pinpoint crystalline defects in SiGe/GeSn optoelectronic materials by measuring nanoscale thermal transport and quantifying thermal conductivity and interfacial thermal resistance in thin spin-on materials used in extreme ultraviolet lithography (eUV) fabrication processing. The new capability of xSThM demonstrated here for the first time is poised to provide vital insights into thermal transport in advanced nanoscale materials and devices.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanoscale mapping of thermal and mechanical properties of bare and metal-covered self-assembled block copolymer thin films

  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Spièce, Jean
  • Evangeli, Charalambos|||0000-0003-3867-8530
  • Robson, Alexander James
  • Kreuzer, Martin|||0000-0002-7305-5016
  • Rodríguez Laguna, María del Rocío|||0000-0001-5582-1728
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Kolosov, Oleg Victor|||0000-0003-3278-9643
  • Alzina, Francesc|||0000-0002-7082-0624
We report on the structural, mechanical, and thermal analysis of 40 nm thick polystyrene-block-poly(ethylene oxide) (PS-b-PEO) block copolymer (BCP) films coated with evaporated chromium layers of different thicknesses (1, 2, and 5 nm). Solvent annealing processes allow the structural control of the BCP films morphology by rearranging the position of the PEO cylinders parallel to the substrate plane. High-vacuum scanning thermal microscopy and ultrasonic force microscopy measurements performed in ambient pressure revealed that coated ultrathin metal layers strongly influence the heat dissipation in the BCP films and the local surface stiffness of the individual BCP domains, respectively. The measured tip-sample effective thermal resistance decreases from 6.1 × 107 to 2.5 × 107 K W-1 with increasing Cr film thickness. In addition, scanning probe microscopy measurements allow the thermal and mechanical mapping of the two segregated polymer domains (PEO-PS) of sub-50 nm characteristic sizes, with sub-10 nm thermal spatial resolution. The results revealed the effect of the surface morphology of the BCP and the incorporation of the metal film on the nanoscale thermal properties and volume self-assembly on the mechanical properties. The findings from this study provide insight into the formation of high aspect ratio BCP-metal structures with the more established applications in lithography. In addition, knowledge of the thermal and mechanical properties at the nanoscale is required in emergent applications, where BCPs, or polymers in general, are part of the structure or device. The performance of such devices is commonly related to the requirement of increased heat dissipation while maintaining mechanical flexibility.