Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Electrochemical Synthesis of an Organic Thermoelectric Power Generator

  • Serrano-Claumarchirant. José F.
  • Brotons-Alcázar, Isaac
  • Culebras, M.
  • Cantarero, A.
  • Muñoz-Espí, Rafael
  • Gomez, C.M.
  • Sanchis Sánchez, María Jesús|||0000-0002-3528-3966
[EN] Energy harvesting through residual heat is considered one of the most promising ways to power wearable devices. In this work, thermoelectric textiles were prepared by coating the fabrics, first with multiple-wall carbon nanotubes (MWCNTs) by using the layer-by-layer technique and second with poly(3,4-ethylenedioxythiophene) (PEDOT) deposited by electrochemical polymerization. Sodium deoxycholate and poly(diallyldimethylammonium chloride) were used as stabilizers to prepare the aqueous dispersions of MWCNTs. The electrochemical deposition of PEDOT on the MWCNT-coated fabric was carried out in a three-electrode electrochemical cell. The polymerization of PEDOT on the fabric increased the electrical conductivity by ten orders of magnitude (through the plane), establishing an excellent path for electric transport across the fabrics. In addition, the fibers showed a Seebeck coefficient of 14.3 ¿V K¿1, which is characteristic of highly doped PEDOT. As a proof of concept, several thermoelectric modules were made with different elements based on the coated acrylic and cotton fabrics. The best generator made of 30 thermoelectric elements using acrylic fabrics exhibited an output power of 0.9 ¿W with a temperature difference of 31 K., This research was supported by the General Direction of Scientific and Technical Research of the Spanish Government through a grant of the Program Consolider Ingenio (grant no. CSD2010-0044) and grant MAT2015-63955-R. J.F.S.-C. and I.B.-A. acknowledge the financial support by the Spanish Ministry of Education, Culture and Sport through the FPU Training Program. Finally, R.M.-E. thanks the financial support of the Spanish Ministry of Science and Innovation through a Ramon y Cajal grant (grant no. RYC-2013-13451).
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A single-source precursor route to anisotropic halogen-doped zinc oxide particles as a promising candidate for new transparent conducting oxide materials

  • Lehr, Daniela
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Flock, Johanna
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Klaiber, Alexander
  • Dekorsy, Thomas
  • Polarz, Sebastian
Numerous applications in optoelectronics require electrically conducting materials with high optical transparency over the entire visible light range. A solid solution of indium oxide and substantial amounts of tin oxide for electronic doping (ITO) is currently the most prominent example for the class of so-called TCOs (transparent conducting oxides). Due to the limited, natural occurrence of indium and its steadily increasing price, it is highly desired to identify materials alternatives containing highly abundant chemical elements. The doping of other metal oxides (e.g., zinc oxide, ZnO) is a promising approach, but two problems can be identified. Phase separation might occur at the required high concentration of the doping element, and for successful electronic modification it is mandatory that the introduced heteroelement occupies a defined position in the lattice of the host material. In the case of ZnO, most attention has been attributed so far to n-doping via substitution of Zn²+ by other metals (e.g., Al³+). Here, we present first steps towards n-doped ZnO-based TCO materials via substitution in the anion lattice (O²- versus halogenides). A special approach is presented, using novel single-source precursors containing a potential excerpt of the target lattice 'HalZn·Zn₃O₃' preorganized on the molecular scale (Hal = I, Br, Cl). We report about the synthesis of the precursors, their transformation into halogene-containing ZnO materials, and finally structural, optical and electronic properties are investigated using a combination of techniques including FT-Raman, low- T photoluminescence, impedance and THz spectroscopies.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Correction, A single-source precursor route to anisotropic halogen-doped zinc oxide particles as a promising candidate for new transparent conducting oxide materials

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal conductivity of MoS2 polycrystalline nanomembranes

  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Placidi, Marcel
  • Saleta Reig, David|||0000-0003-3189-2331
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Alzina, Francesc|||0000-0002-7082-0624
  • Mortazavi, Bohayra|||0000-0003-3031-5057
  • Quey, Romain|||0000-0002-1593-8179
  • Colombo, Luciano|||0000-0001-5335-4652
  • Roche, Stephan|||0000-0003-0323-4665
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Heat conduction in 2D materials can be effectively engineered by means of controlling nanoscale grain structure. Afavorable thermal performance makes these structures excellent candidates for integrated heat management units. Here we show combined experimental and theoretical studies for MoS₂ nanosheets in a nanoscale grain-size limit.Wereport thermal conductivity measurements on 5 nm thick polycrystalline MoS₂ by means of 2-laser Raman thermometry. The free-standing, drum-like MoS₂ nanomembranes were fabricated using a novel polymer- and residue-free, wet transfer, in which we took advantage of the difference in the surface energies between MoS₂ and the growth substrate to transfer the CVD-grown nanosheets. The measurements revealed a strong reduction in the in-plane thermal conductivity down to about 0.73 ± 0.25 W m⁻¹ K⁻¹. The results are discussed theoretically using finite elements method simulations for a polycrystalline film, and a scaling trend of the thermally conductivity with grain size is proposed.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Reduction of the thermal conductivity in free-standing silicon nano-membranes investigated by non-invasive Raman thermometry

  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Cuffe, John|||0000-0003-2915-5383
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Shchepetov, Andrey
  • Jiang, Hua
  • Prunnila, Mika
  • Ahopelto, Jouni|||0000-0003-3372-6097
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We report on the reduction of the thermal conductivity in ultra-thin suspended Si membranes with high crystalline quality. A series of membranes with thicknesses ranging from 9 nm to 1.5 μm was investigated using Raman thermometry, a novel contactless technique for thermal conductivity determination. A systematic decrease in the thermal conductivity was observed as reducing the thickness, which is explained using the Fuchs-Sondheimer model through the influence of phonon boundary scattering at the surfaces. The thermal conductivity of the thinnest membrane with d = 9 nm resulted in (9 ± 2) W/mK, thus approaching the amorphous limit but still maintaining a high crystalline quality.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Thermal conductivity and air-mediated losses in periodic porous silicon membranes at high temperatures

  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Wu, Yang|||0000-0002-0128-7280
  • Volz, Sebastian
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Heat conduction in silicon can be effectively engineered by means of sub-micrometre porous thin free-standing membranes. Tunable thermal properties make these structures good candidates for integrated heat management units such as waste heat recovery, rectification or efficient heat dissipation. However, possible applications require detailed thermal characterisation at high temperatures which, up to now, has been an experimental challenge. In this work we use the contactless two-laser Raman thermometry to study heat dissipation in periodic porous membranes at high temperatures via lattice conduction and air-mediated losses. We find the reduction of the thermal conductivity and its temperature dependence closely correlated with the structure feature size. On the basis of two-phonon Raman spectra, we attribute this behaviour to diffuse (incoherent) phonon-boundary scattering. Furthermore, we investigate and quantify the heat dissipation via natural air-mediated cooling, which can be tuned by engineering the porosity.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanoparticle shape anisotropy and photoluminescence properties, Europium containing ZnO as a model case

  • Gerigk, Melanie
  • Ehrenreich, Philipp
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Wimmer, Ilona
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Schmidt-Mende, Lukas
  • Polarz, Sebastian
The precise control over electronic and optical properties of semiconductor (SC) materials is pivotal for a number of important applications like in optoelectronics, photocatalysis or in medicine. It is well known that the incorporation of heteroelements (doping as a classical case) is a powerful method for adjusting and enhancing the functionality of semiconductors. Independent from that, there already has been a tremendous progress regarding the synthesis of differently sized and shaped SC nanoparticles, and quantum-size effects are well documented experimentally and theoretically. Whereas size and shape control of nanoparticles work fairly well for the pure compounds, the presence of a heteroelement is problematic because the impurities interfere strongly with bottom up approaches applied for the synthesis of such particles, and effects are even stronger, when the heteroelement is aimed to be incorporated into the target lattice for chemical doping. Therefore, realizing coincident shape control of nanoparticle colloids and their doping still pose major difficulties. Due to a special mechanism of the emulsion based synthesis method presented here, involving a gelation of emulsion droplets prior to crystallization of shape-anisotropic ZnO nanoparticles, heteroelements can be effectively entrapped inside the lattice. Different nanocrystal shapes such as nanorods, -prisms, -plates, and -spheres can be obtained, determined by the use of certain emulsification agents. The degree of morphologic alterations depends on the type of incorporated heteroelement M, concentration, and it seems that some shapes are more tolerant against doping than others. Focus was then set on the incorporation of Eu³⁺ inside the ZnO particles, and it was shown that nanocrystal shape and aspect ratios could be adjusted while maintaining a fixed dopant level. Special PL properties could be observed implying energy transfer from ZnO excited near its band-gap (3.3 eV) to the Eu³⁺ states mediated by defect luminescence of the nanoparticles. Indications for an influence of shape on photoluminescence (PL) properties were found. Finally, rod-like Eu@ZnO colloids were used as tracers to investigate their uptake into biological samples like HeLa cells. The PL was sufficient for identifying green and red emission under visible light excitation.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Hypersonic phonon propagation in one-dimensional surface phononic crystal

  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Kehagias, Nikolaos|||0000-0002-2698-383X
  • Alzina, Francesc|||0000-0002-7082-0624
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
Hypersonic, thermally activated surface acoustic waves propagating in the surface of crystalline silicon patterned with periodic stripes were studied by Brillouin light scattering. Two characteristic directions (normal and parallel to the stripes) of surface acoustic waves propagation were examined exhibiting a distinctive propagation behavior. The measured phononic band structure exhibits diverse features, such as zone folding, band gap opening, and hybridization to local resonance for waves propagating normal to the stripes, and a variety of dispersive modes propagating along the stripes. Experimental results were supported by theoretical calculations performed using finite element method.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Acoustic phonon propagation in ultra-thin Si membranes under biaxial stress field

  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Alzina, Francesc|||0000-0002-7082-0624
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Shchepetov, Andrey
  • Prunnila, Mika
  • Ahopelto, Jouni|||0000-0003-3372-6097
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We report on stress induced changes in the dispersion relations of acoustic phonons propagating in 27 nm thick single crystalline Si membranes. The static tensile stress (up to 0.3 GPa) acting on the Si membranes was achieved using an additional strain compensating silicon nitride frame. Dispersion relations of thermally activated hypersonic phonons were measured by means of Brillouin light scattering spectroscopy. The theory of Lamb wave propagation is developed for anisotropic materials subjected to an external static stress field. The dispersion relations were calculated using the elastic continuum approximation and taking into account the acousto-elastic effect. We find an excellent agreement between the theoretical and the experimental dispersion relations.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Spatial mapping of exciton lifetimes in single ZnO nanowires

  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Callsen, Gordon|||0000-0001-6390-3977
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Güell, Frank|||0000-0002-6528-9007
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Hoffmann, Axel
We investigate the spatial dependence of the exciton lifetimes in single ZnO nanowires. We have found that the free exciton and bound exciton lifetimes exhibit a maximum at the center of nanowires, while they decrease by 30% towards the tips. This dependence is explained by considering the cavity-like properties of the nanowires in combination with the Purcell effect. We show that the lifetime of the bound-excitons scales with the localization energy to the power of 3/2, which validates the model of Rashba and Gurgenishvili at the nanoscale.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Tuning Thermal Transport in Ultrathin Silicon Membranes by Surface Nanoscale Engineering

  • Neogi, Sanghamitra
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Pereira, Luiz Felipe C.
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Shchepetov, Andrey
  • Prunnila, Mika
  • Ahopelto, Jouni|||0000-0003-3372-6097
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
  • Donadio, Davide|||0000-0002-2150-4182
A detailed understanding of the connections of fabrication and processing to structural and thermal properties of low-dimensional nanostructures is essential to design materials and devices for phononics, nanoscale thermal management, and thermoelectric applications. Silicon provides an ideal platform to study the relations between structure and heat transport since its thermal conductivity can be tuned over 2 orders of magnitude by nanostructuring. Combining realistic atomistic modeling and experiments, we unravel the origin of the thermal conductivity reduction in ultrathin suspended silicon membranes, down to a thickness of 4 nm. Heat transport is mostly controlled by surface scattering: rough layers of native oxide at surfaces limit the mean free path of thermal phonons below 100 nm. Removing the oxide layers by chemical processing allows us to tune the thermal conductivity over 1 order of magnitude. Our results guide materials design for future phononic applications, setting the length scale at which nanostructuring affects thermal phonons most effectively.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Two-Dimensional Phononic Crystals, Disorder Matters

  • Wagner, Markus R.|||0000-0002-7367-5629
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Sachat, Alexandros el|||0000-0003-3798-9724
  • Sledzinska, Marianna|||0000-0001-8592-1121
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
The design and fabrication of phononic crystals (PnCs) hold the key to control the propagation of heat and sound at the nanoscale. However, there is a lack of experimental studies addressing the impact of order/disorder on the phononic properties of PnCs. Here, we present a comparative investigation of the influence of disorder on the hypersonic and thermal properties of two-dimensional PnCs. PnCs of ordered and disordered lattices are fabricated of circular holes with equal filling fractions in free-standing Si membranes. Ultrafast pump and probe spectroscopy (asynchronous optical sampling) and Raman thermometry based on a novel two-laser approach are used to study the phononic properties in the gigahertz (GHz) and terahertz (THz) regime, respectively. Finite element method simulations of the phonon dispersion relation and three-dimensional displacement fields furthermore enable the unique identification of the different hypersonic vibrations. The increase of surface roughness and the introduction of short-range disorder are shown to modify the phonon dispersion and phonon coherence in the hypersonic (GHz) range without affecting the room-temperature thermal conductivity. On the basis of these findings, we suggest a criteria for predicting phonon coherence as a function of roughness and disorder.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Modification of Akhieser mechanism in Si nanomembranes and thermal conductivity dependence of the Q-factor of high frequency nanoresonators

  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Zarate, Ramón A.
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We present and validate a reformulated Akhieser model that takes into account the reduction of thermal conductivity due to the impact of boundary scattering on the thermal phonons' lifetime. We consider silicon nanomembranes with mechanical mode frequencies in the GHz range as textbook examples of nanoresonators. The model successfully accounts for the measured shortening of the mechanical mode lifetime. Moreover, the thermal conductivity is extracted from the measured lifetime of the mechanical modes in the high-frequency regime, thereby demonstrating that the Q-factor can be used as an indication of the thermal conductivity and/or diffusivity of a mechanical resonator.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A novel contactless technique for thermal field mapping and thermal conductivity determination, two-laser Raman thermometry

  • Reparaz, Juan Sebastián|||0000-0001-9679-0075
  • Chávez Ángel, Emigdio|||0000-0002-9783-0806
  • Wagner, Markus R.|||0000-0002-7367-5629
  • Graczykowski, Bartlomiej|||0000-0003-4787-8622
  • Gomis-Bresco, Jordi|||0000-0002-6066-7064
  • Alzina, Francesc|||0000-0002-7082-0624
  • Sotomayor Torres, Clivia M.|||0000-0001-9986-2716
We present a novel contactless technique for thermal conductivity determination and thermal field mapping based on creating a thermal distribution of phonons using a heating laser, while a second laser probes the local temperature through the spectral position of a Raman active mode. The spatial resolution can be as small as 300 nm, whereas its temperature accuracy is ±2 K. We validate this technique investigating the thermal properties of three free-standing single crystalline Si membranes with thickness of 250, 1000, and 2000 nm. We show that for two-dimensional materials such as free-standing membranes or thin films, and for small temperature gradients, the thermal field decays as T(r) ∝ ln(r) in the diffusive limit. The case of large temperature gradients within the membranes leads to an exponential decay of the thermal field, T ∝ exp[ - A·ln(r)]. The results demonstrate the full potential of this new contactless method for quantitative determination of thermal properties. The range of materials to which this method is applicable reaches far beyond the here demonstrated case of Si, as the only requirement is the presence of a Raman active mode.