Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Mixed Ionic-Electronic Conduction in NiFe2O4-Ce0.8Gd0.2O2-delta Nanocomposite Thin Films for Oxygen Separation

  • Solis Díaz, Cecilia
  • Toldrá-Reig, Fidel
  • Somacescu, Simona
  • García-Fayos, Julio
  • Palafox, Elena
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] NiFe2O4-Ce0.8Gd0.2O2-delta (NFO/CGO) nanocomposite thin films were prepared by simultaneously radio-frequency (RF) magnetron sputtering of both NFO and CGO targets. The aim is the growth of a CO2-stable composite layer that combines the electronic and ionic conduction of the separate NFO and the CGO phases for oxygen separation. The effect of the deposition temperature on the microstructure of the film was studied to obtain high-quality composite thin films. The ratio of both phases was changed by applying different power to each ceramic target. The amount of each deposited phase as well as the different oxidation states of the nanocomposite constituents were analyzed by means of X-ray photoelectron spectroscopy (XPS). The transport properties were studied by conductivity measurements as a function of temperature and pO(2). These analyses enabled (1)selection of the best deposition temperature (400 degrees C), (2)correlation of the p-type electronic behavior of the NFO phase with the hole hopping between Ni3+-Ni2+, and (3)following the conductivity behavior of the grown composite layer (prevailing ionic or electronic character) attained by varying the amount of each phase. The sputtered layer exhibited high ambipolar conduction and surface-exchange activity. A 150 nm-thick nanograined thin film was deposited on a 20 mu m-thick Ba0.5Sr0.5Co0.8Fe0.2O3-delta asymmetric membrane, resulting in up to 3.8 mLmin(-1)cm(-2) O-2 permeation at 1000 degrees C under CO2 atmosphere., Funding from European Union (FP7 Project Green-CC- Grant Agreement 608524), the Spanish Government (ENE2014-57651 and SEV-2016-0683) is kindly acknowledged. The authors also want to acknowledge the Electron Microscopy Service from the Universitat Politecnica de Valencia for their support in the SEM analysis performed in this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermochemical stability of LaxSr1-xCoyFe1-yO3-delta and NiFe2O4-Ce0.8Tb0.2O2-delta, under real conditions for its application in oxygen transport membranes for oxyfuel combustion

  • Bermúdez, José M.
  • García-Fayos, Julio
  • Reina, Tomás R.
  • Reed, Graham
  • Persoon, E.
  • Görtz, Daniel
  • Schroeder, M.
  • Millán, M
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] This work addresses the thermochemical stability of ceramic materials ¿typically used in oxygen transport membranes¿ under the harsh gas environments found in oxyfuel combustion processes. Specifically, a dual-phase NiFe2O4-Ce0.8Tb0.2O2-¿ (NFO-CTO) composite and a single-phase La0.6Sr0.4Co0.2Fe0.8O3-¿ (LSCF) were studied. The effect of the main contaminants present in this kind of processes (CO2, SO2 and H2O) has been tested. NFO-CTO composite remains stable under all the conditions studied whereas LSCF presents a poor stability in the presence of CO2 and SO2. Regardless of the treatment, NFO-CTO conserves its crystalline structure, without giving rise to new species due to segregation or incorporation of sulphur and/or carbon. On the contrary, LSCF is prone to degradation in contact with CO2 and SO2, segregating Sr in the form of SrCO3 and SrSO4 and Co and Fe in the form of CoO and Fe3O4. It is also shown that SO2 interaction with LSCF is stronger than in the case of CO2. A concentration of just 2000¿ppm of SO2 in CO2 is enough to subdue the formation of SrCO3, promoting the segregation of Sr only in the form of SrSO4. With the results presented in this work, it is possible to conclude that the NFO-CTO is a suitable candidate from the thermochemical viewpoint to be used as membrane material in 4-end modules for oxygen generation integrated into oxyfuel combustion processes whereas the use of LSCF should be dismissed., Financial support by the EU through FP7 GREEN-CC Project (Grant Agreement Number: 608524). The Spanish Government (ENE2014-57651 and SEV-2016-0683 grants) is gratefully acknowledged by JGF and JMS.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Improving the performance of oxygen transport membranes in simulated oxy-fuel power plant conditions by catalytic surface enhancement

  • Pirou, Stéven
  • García-Fayos, Julio
  • Kiebach, Ragnar
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The stability of dual-phase oxygen transport membranes consisting of 70 vol% (Y2O3)(0.01)(Sc2O3)(0.10)(ZrO2)(0.89) and 30 vol% MnCo2O4 (10Sc1YSZ-MCO (70-30 vol%)) was investigated in simulated oxy-fuel power plant fluegas (250 ppm SO2, 5% O-2, 3% H2O, balance CO2). Additionally, the influence of catalytic porous backbones on the performance of the membrane was studied in the same conditions. The chemical stability of the dual-phase membrane was investigated by X-ray diffraction (XRD), Raman spectroscopy and field emission scanning electron microscopy (FE SEM). The tests performed before and after the exposure to the simulated flue gas showed excellent chemical stability. Electrochemical impedance spectroscopy (EIS) measurements were performed on activated (Ce-Pr catalyst) and non-activated porous catalytic backbones made of: (i) (Y2O3)(0.08)(ZrO2)(0.92) (8YSZ), (ii) 8YSZ-MCO (40-60 vol%), (iii) 10Sc1YSZ-MCO (40-60 vol%), (iv) 10Sc1YSZ-MCO (70-30 vol%), and (v) Ce0.8Tb0.2O2-d (CTO)-NiFe2O4 (NFO) (40-60 vol%) to achieve a better understanding of the oxygen surface reactions (especially in SO2 and CO2 containing atmospheres). The lowest polarization resistances (R-p) were found for 10Sc1YSZ-MCO (40-60 vol%) and CTO-NFO (40-60 vol%) porous backbones. Oxygen permeation tests realized on 10Sc1YSZ-MCO membranes demonstrated that the catalytic porous backbones can significantly influence the oxygen permeation flux, and improvements of up to 55% were achieved. Both EIS and oxygen permeation measurements showed a significant influence of SO2 on the oxygen oxidation/reduction reactions (increase of R-p, decrease of oxygen permeation fluxes) due to SO2 adsorption and blocking of active sites for the oxygen reactions. Nevertheless, no microstructural degradation was found after SO2 exposure and initial Rp values and oxygen permeation fluxes could be recovered in most cases., The financial support from EU through the "Graded Membranes for Energy Efficient New Generation Carbon Capture Process (GREEN-CC)" project (Grant agreement no. 608524) is gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Oxygen permeation improvement under CO2-rich environments through catalytic activation of hierarchically-structured perovskite membranes

  • Gaudillere, Cyril Christian
  • García Fayos, Julio
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Catalytic activation of a highly porous La0.6Sr0.4Co0.2Fe0.8O3- (LSCF) freeze-cast asymmetric membrane has been realized by screen-printing a 30m thick LSCF porous layer over the dense top layer of the asymmetric membrane. Membrane activation leads to a noticeable improvement of the oxygen permeation flux (JO(2)) in the low-temperature region (<700 degrees C), at which catalytic gas exchange is the most limiting process. An enhancement of 54% in JO(2) is obtained (JO(2)=0.17mLmin(-1)cm(-2)) in air at 600 degrees C thanks to the addition of the LSCF catalytic porous layer, whereas the maximum oxygen permeation is reached when pure oxygen is fed to the membrane at 1000 degrees C with a high value of 16.3mLmin(-1)cm(-2). The most appealing effect of the catalytic layer is its protective feature under oxycombustion conditions, that is, under a CO2-rich atmosphere at high temperature. Indeed, the oxygen permeation drop in the presence of CO2 is significantly lower in the presence of a catalytic porous layer. Interestingly, the full recovery of JO(2) flux after CO2 removal in the sweep flux evidences the absence of a carbonation process. Finally, the stability of the functionalized membrane was evaluated at 850 degrees C and under a 50% CO2-containing atmosphere; this revealed a linear degradation rate for oxygen permeation of 4.27x10(-2)mLmin(-1)cm(-2) per day., Funding from the Spanish Government (ENE2011-24761 and SEV-2012-0267 grants) and EC (FP7 GREEN-CC Grant Agreement 608524) is kindly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Freeze-casting: Fabrication of highly porous and hierarchical ceramic supports for energy applications

  • Gaudillere, Cyril Christian
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The manufacture of structured ceramic porous support knows an important boom since more than a decade with the development of new shaping techniques. Among the most promising ones, the freeze-casting also called Ice-Templating allows the fabrication of ceramic parts exhibiting high porosity (>50%) and vertically aligned and hierarchically organized pores. Such structures were firstly conceived for biomedical applications like bone substitute and tissue engineering, but the distinctive features of freeze-cast structures have attracted the attention of diverse scientific fields, especially in high temperature ceramic based energy production systems. Indeed, technologies like (a) Solid Oxide Fuel Cell (SOFC) and Electrolyser Cell (SOEC), (b) gas separation (O-2, H-2) by asymmetric supported membranes based on mixed ionic and electronic conductors (MIEC) or hydrogen-permeable metals, and (c) Catalytic Membrane Reactor (CMR) systems present a porous component in their physical structure. This latest, presenting a tortuous pathway for gas access and as a consequence, a high transport limitation, is known to be a limiting component for the operation at high flow streams that would enable to reach industrial target. The aim of this paper is to give an overview of the freeze-casting ceramic shaping method and to show how its implementation could be useful for several energy applications where key components comprise a porous scaffold. A detailed presentation of the freeze-casting process and of the characteristics of the resulting porous parts is firstly given. The characteristic of freeze-cast parts and the drawbacks of conventional porous scaffolds existing in energy applications are drawn in order to highlight the expected beneficial effect of this new shaping technique as possible substitute to the conventional ones. Finally, a review of the state of the art freeze-cast based energy applications developed up to now and expected to be promising is given to illustrate the large perspectives opened by the implementation of the freeze-casting of ceramics for energy fields. Here we suggest discussing about the feasibility of incorporate freeze-cast porous support in high temperature ceramic-based energy applications. (C) 2016 SECV. Published by Elsevier Espana, S.L.U., [ES] La fabricación de soportes cerámicos porosos a través de nuevas técnicas de conformado es clave en el desarrollo de nuevos dispositivos en el sector energético y de la ingeniería química. La técnica de freeze-casting (colado por congelación) permite obtener componentes cerámicos muy bien sinterizados, con muy alta porosidad y poros con formas concretas. Los poros se orientan de manera que las propiedades de transporte de fluidos a su través son óptimos con respecto a otros tipos de estructuras porosas más irregulares. Concretamente, en el sector de la energía los soportes porosos se utilizan en aplicaciones tales como pilas de combustibles de óxidos sólidos o electrolizadores, membranas para la separación de gases, típicamente O2 o H2, y reactores catalíticos de membrana. En este artículo se revisan de manera exhaustiva los desarrollos en estos campos utilizando freeze-casting para el conformado de cuerpos porosos cerámicos. © 2016 SECV. Publicado por Elsevier España, S.L.U, Financial support by the Spanish Ministry for Science and Innovation (ENE2011-24761 and SEV-2012-0267 grants) and by the EU through FP7 GREEN-CC Project (Grant Agreement Number: 608524) is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Oxygen transport membranes in a biomass/coal combined strategy for reducing CO2 emissions: Permeation study of selected membranes under different CO2-rich atmospheres

  • García Fayos, Julio
  • Vert Belenguer, Vicente Bernardo
  • Solis Díaz, Cecilia
  • Gaudillere, Cyril Christian
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] This contribution introduces how the integration of biomass as fuel in power plants would balance CO2 emissions and the related role of oxygen transport membranes (OTM) on it. CO2 capture techniques could be introduced to minimize CO2 emissions at the cost of a substantial energy penalty in the overall process. Among the different approaches, the use of pure O2 and/or N2-free oxidation gases for combustion and/or for gasification leads to promising energy efficiencies. Ceramic OTM membranes could be successfully integrated in such thermal processes, which enable to increase the net plant efficiency when CO2 capture is implemented. Further, this work reviews how selected ceramic materials and membrane architectures behave under CO2 containing atmospheres at high temperatures above 700 °C. These conditions have been selected for checking the viability of these membrane compositions and configurations to fit in an oxy-co-gasification process, involving coal and biomass. The tested asymmetric membranes present competitive oxygen fluxes in the range 0.6 1.2 ml min&#8722;1 cm&#8722;2 when using CO2 as (inlet) sweep gas at 850 °C (optimal membrane operation conditions in oxy-fuel power plant) and stable oxygen production up to 100 h of continuous operation in similar conditions. Specifically, La0.6Sr0.4Co0.2Fe0.8O3&#8722;ä and NiFe2O4 Ce0.8Tb0.2O2&#8722;ä composite materials showed the best results for oxygen permeation and time stability under CO2-rich atmospheres., Financial support by the Spanish Government (ENE2011-24761 and SEV-2012-0267 grants), by the EU through FP7 GREEN-CC Project (GA 608524), and by the Helmholtz Association of German Research Centers through the Helmholtz Portfolio MEM-BRAIN is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Maximizing oxygen permeation via catalytic functionalization under oxyfuel conditions

  • Almar-Liante, Laura|||0000-0001-5103-3812
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
  • Garcia-Fayos, Julio
  • Ruhl, Rian
  • Navarrete Algaba, Laura
  • Laqdiem-Marin, Marwan
  • Joo, Jong Hoon
  • Bouwmeester, Henny J. M.
[EN] Oxygen transport membranes (OTMs) offer a promising route for high-efficiency, cost-effective oxygen supply in energy and chemical industries, with the potential to significantly reduce CO2 and NOx emissions when integrated into oxy-combustion processes. However, conventional OTMs suffer from poor chemical stability in CO2-rich environments, prompting the development of dual-phase membranes that, while more stable, typically exhibit lower oxygen permeation rates. In this study, we address this limitation by enhancing the surface exchange kinetics of Fe2NiO4-Ce0.8Tb0.2O2-delta (NFO-CTO) membranes by surface modification with various oxygen oxidation-reduction reaction (OORR) catalysts, including Ce, Pr, Sm, Tb, Co, Nb, Zr, and Al oxides, and Pr-based binary oxides. Comprehensive characterization using electrochemical impedance spectroscopy, oxygen isotopic exchange, and gas permeation measurements revealed a substantial improvement in surface reaction kinetics. Catalyst activation led to a six-fold increase in oxygen flux under standard conditions and up to a 2.5-fold enhancement under harsh environments containing CO2 and SO2 at 850 degrees C, mimicking oxyfuel combustion conditions. This work demonstrates that rational catalyst selection and integration can overcome fundamental surface limitations in dual-phase membranes, offering a viable strategy to advance oxygen separation technologies for sustainable energy applications., Financial support from the Spanish Government (PID2022-139663OB-100 and CEX2021-001230-S grant funded by MCIN/AEI/10.13039/501100011033) and the Generalitat Valenciana (CIPROM/2022/10) is also acknowledged. Financial support by the EU through FP7 GREEN-CC Project (Grant Agreement Number: 608524). We thank the support of the Electronic Microscopy Service of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Enhancing oxygen permeation through Fe2NiO4-Ce0.8Tb0.2O2-delta composite membranes using porous layers activated with Pr6O11 nanoparticles

  • García-Fayos, Julio
  • Ruhl, R.
  • Navarrete Algaba, Laura
  • Bouwmeester, H.
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Fe2NiO4-Ce0.8Tb0.2O2-delta (NFO-CTO) composite membranes are of interest to separate oxygen from air. In this study, we investigate the influence of the catalytic activation of NFO-CTO membranes on the oxygen permeation rate. Specifically, the effect of activating porous NFO-CTO layers -coated on both sides of the dense NFO-CTO membrane - with Pr6O11 nanoparticles is studied. Measurements in the temperature range 850-700 degrees C revealed a 2-4 fold increase in the oxygen flux after coating a 30 mm-thick porous NFO-CTO layer on both membrane sides, and a 6-12 fold increase relative to the bare membrane after activating the porous layers coated on both sides of the membrane with Pr6O11 nanoparticles. No degradation of the oxygen fluxes was found in CO2-containing atmospheres. Pulse isotopic exchange measurements confirmed an increase in the oxygen surface exchange rate of more than one order of magnitude after dispersion of Pr6O11 nanoparticles on the surface of NFO-CTO composite powders. Electrochemical impedance spectroscopy measurements on symmetrical cells, using Gd-doped ceria (CGO) as the electrolyte and Pr6O11-activated NFO-CTO electrodes, showed a 10-fold decrease in the polarization resistance compared to non-infiltrated electrodes in air. Modification of porous layers by activation with Pr6O11 nanoparticles is considered a viable route to enhance the oxygen fluxes across composite membranes., Financial support by the EU through FP7 GREEN-CC Project (Grant Agreement Number: 608524) and the Spanish Government (ENE2014-57651 and SEV-2016-0683 grants) is gratefully acknowledged. The support of the Servicio de Microscopia Electronica of the Universitat Politecnica de Valencia is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Catalyst Screening for Oxidative Coupling of Methane Integrated in Membrane Reactors

  • García-Fayos, Julio
  • Lobera González, Maria Pilar
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Increased availability of methane from shale gas and stranded gas deposits in the recent years may facilitate the production of ethylene by means of potentially more competitive routes than the state-of-the-art steam cracking processes. One appealing route is the oxidative coupling of methane (OCM), which is considered in this work for the production of ethylene by means of the use of catalytic membrane reactors (CMR) based on Ba0.5Sr0.5Co0.8Fe0.2O3-delta (BSCF) ceramic material. In a first approach, a screening of 15 formulations as catalysts for the ethylene-ethane production was conducted on CMR consisting of disk-shaped planar BSCF membranes. At 900 degrees C, the maximum C-2 selectivity was 70%, reached with Ba0.5Sr0.5FeO3-delta and La0.5Ce0.1Sr0.4Co0.8Fe0.2O3-delta catalysts. On the other hand, low CH4 conversions (X-CH4) resulted in C-2 yields below 3%. Operation at 1,000 degrees C significantly shifted X-CH4 for all the activated membranes due to the decrease in CH4/O-2 ratios, thus obtaining C-2 yields close to 9% and productivities of ca. 1.2ml.min(-1).cm(-2) with Ce0.9Gd0.1O2-delta and Ba0.5Sr0.5Co0.8Fe0.2O3-delta impregnated with Mn-Na2WO4 catalysts. The performance of OCM reaction was also studied in a tubular catalytic membrane reactor. Tubular configuration improved C-2 yield by minimizing CH4/O-2 ratios up to 1.7, obtaining a maximum of 15.6% at 900 degrees C with a BSCF capillary membrane activated with a packed bed of 2 wt% Mn/5 wt% Na2WO4 on SiO2 catalyst., Financial support by the Spanish Government (ENE2014-57651 and SEV-2012-0267 grants) and by the EU through FP7 GREEN-CC Project (GA 608524), is gratefully acknowledged. The authors want also acknowledge the Electron Microscopy Service from the Universitat Politecnica de Valencia for their support in the SEM analysis performed in this work.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dual-phase membrane based on LaCo0.2Ni0.4Fe0.4O3-x-Ce0.8Gd0.2O2-x composition for oxygen permeation under CO2/SO2-rich gas environments

  • García-Fayos, Julio
  • Baunmann, Stefan
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] A dual-phase material with high ambipolar conductivity composed by the perovskite LaCo0.2Ni0.4Fe0.4O3-delta (LCNF) as the electronic phase and the fluorite Ce0.8Gd0.2O2-delta (CGO20) as oxide-ion conductor is proposed for use as oxygen transport membrane. The chemical compatibility between both materials depends on the synthesis method, i.e. one-pot sol-gel synthesis leads to the formation of the fluorite and the perovskite phases, as well as a third NiO-based phase. The formation of this last phase can be avoided by previously stabilizing the phases separately. The composite material shows high electrical conductivity, i.e., 7.25 S cm(-1) at 800 degrees C for LCNF-CGO20 with NiO impurity, and 2.6 S cm(-1) at 800 degrees C for LCNF-CGO20. A maximum oxygen flux, J(O-2), of 0.74 ml min(-1) cm(-2) is obtained at 1000 degrees C for a surface-activated membrane in Air/Ar gradient at ambient pressure. The membranes were tested under i) 30% CO2 in Ar, and ii) 250 ppm of SO2 in 30% CO2 in Ar, reproducing oxyfuel-like conditions. Oxygen flux decreases in these atmospheres, especially at temperatures below 900 degrees C, due to competitive adsorption of these gases with the O-2. After CO2 and SO2 exposure, initial oxygen fluxes are recovered when switching back to Ar sweeping at temperatures above 900 degrees C. Nevertheless, at temperatures < 900 degrees C the original J(O-2) before SO2 exposure is not fully recovered and postmortem FESEM images reveal the membrane surface degradation in SO2., Financial support by the Spanish Government (ENE2014-57651 and SEV-2016-0683 grants), by the EU through FP7 GREEN-CC Project (GA 608524), and by the Helmholtz Association of German Research Centers through the Helmholtz Portfolio MEM-BRAIN is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dual-Phase Oxygen Transport Membranes for Stable Operation in Environments Containing Carbon Dioxide and Sulfur Dioxide

  • García Fayos, Julio
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] Dual-phase membranes are appealing candidates for oxygen transport membranes owing to their unique combination of ambipolar electron-ion transport and endurance. However, O-2 separation in industrial environments demands very high stability and effectiveness in the presence of CO2- and SO2-bearing process gases. Here, the composition of dual-phase membranes based on NiFe2O4-Ce0.8Tb0.2O2-delta (NFO-CTO) was optimized and the effective performance of catalytically-activated membranes was assessed in presence of CO2 and SO2. Further insight into the limiting mechanisms in the permeation was gained through electrical conductivity studies, permeation testing in several conditions and impedance spectroscopy analysis. The dual-phase membranes were prepared by one-pot sol-gel method and their permeability increases with increasing fluorite content. An O-2 flux of 0.25 (ml min(-1) cm(-2)) mm at 1000 degrees C was obtained for a thick self-standing membrane with 40:60 NFO/CTO composition. An in-depth study mimicking typical harsh conditions encountered in oxyfuel flue gases was performed on a 50:50 NFO/CTO membrane. CO2 content as well as SO2 presence in the sweep gas stream were evaluated in terms of O-2 permeation. O-2 fluxes of 0.13 and 0.09 mL min(-1) cm(-) 2 at 850 degrees C were obtained for a 0.59 mm thick membrane under CO2 and 250 ppm SO2 in CO2 sweep conditions, respectively. Extended periods at work under CO2- and SO2-containing atmospheres revealed good permeation stability over time. Additionally, XRD, backscattered electrons detector (BSD)-SEM, and energy-dispersive X-ray spectroscopy (EDS) analysis of the spent membrane confirmed material stability upon prolonged exposure to SO2., Financial support by the Spanish Ministry for Science and Innovation (ENE2011-24761 and SEV-2012-0267 Grants) and by the EU through FP7 GREEN-CC Project (Grant Agreement Number: 608524) is gratefully acknowledged. The authors would like to express their gratitude to Dr. Cecilia Solis for Scanning Electron Microscopy analysis.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improving the performance of oxygen transport membranes in simulated oxy-fuel power plant conditions by catalytic surface enhancement

  • García-Fayos, Julio
  • Balaguer, María
  • Serra Alfaro, José Manuel
The stability of dual-phase oxygen transport membranes consisting of 70¿vol% (Y2O3)0.01(Sc2O3)0.10(ZrO2)0.89 and 30¿vol% MnCo2O4 (10Sc1YSZ-MCO (70-30¿vol%)) was investigated in simulated oxy-fuel power plant flue-gas (250¿ppm SO2, 5% O2, 3% H2O, balance CO2). Additionally, the influence of catalytic porous backbones on the performance of the membrane was studied in the same conditions. The chemical stability of the dual-phase membrane was investigated by X-ray diffraction (XRD), Raman spectroscopy and field emission scanning electron microscopy (FE SEM). The tests performed before and after the exposure to the simulated flue gas showed excellent chemical stability. Electrochemical impedance spectroscopy (EIS) measurements were performed on activated (Ce-Pr catalyst) and non-activated porous catalytic backbones made of: (i) (Y2O3)0.08(ZrO2)0.92 (8YSZ), (ii) 8YSZ-MCO (40¿60¿vol%), (iii) 10Sc1YSZ-MCO (40¿60¿vol%), (iv) 10Sc1YSZ-MCO (70-30¿vol%), and (v) Ce0.8Tb0.2O2-¿ (CTO) - NiFe2O4 (NFO) (40¿60¿vol%) to achieve a better understanding of the oxygen surface reactions (especially in SO2 and CO2 containing atmospheres). The lowest polarization resistances (Rp) were found for 10Sc1YSZ-MCO (40¿60¿vol%) and CTO-NFO (40¿60¿vol%) porous backbones. Oxygen permeation tests realized on 10Sc1YSZ-MCO membranes demonstrated that the catalytic porous backbones can significantly influence the oxygen permeation flux, and improvements of up to 55% were achieved. Both EIS and oxygen permeation measurements showed a significant influence of SO2 on the oxygen oxidation/reduction reactions (increase of Rp, decrease of oxygen permeation fluxes) due to SO2 adsorption and blocking of active sites for the oxygen reactions. Nevertheless, no microstructural degradation was found after SO2 exposure and initial Rp values and oxygen permeation fluxes could be recovered in most cases., The financial support from EU through the “Graded Membranes for Energy Efficient New Generation Carbon Capture Process (GREEN-CC)” project (Grant agreement no. 608524) is gratefully acknowledged by the authors.