Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Capítulo o parte de un libro (BookPart)

Influencia de la naturaleza y granulometría de los áridos en el comportamiento reológico de morteros de cementos activados alcalinamente

  • Gismera-Diez, Sara
  • Alonso, Maria del Mar
  • Puertas, Francisca
[ES] El objetivo de este trabajo es profundizar en el conocimiento del comportamiento reologico de morteros de cementos activados alcalinamente (Alkali-Activated Materials, AAMs), determinando el efecto del diámetro máximo del árido y su naturaleza (silíceo, calizo y árido reciclado). Morteros de OPC se utilizan de referencia. Se realizaron ensayos de fluidez y de Stress Growth Test; también se determinaron los parámetros reológicos por el ensayo de curva de flujo. Los morteros de AAMs son más sensible que los de OPC a la variación del diámetro máximo de los áridos; aunque no se han observado diferentes comportamientos asociados a la naturaleza del mismo. Se ha demostrado que todos los morteros se ajustan al modelo reológico de Bingham, independientemente del diámetro máximo de los áridos y de la naturaleza de los mismos., Este estudio fue financiado por el Ministerio de Economía (MINECO) bajo el Proyecto del plan Nacional BIA2013-47876-C2-1-P. Los autores desean agradecer a A. Gil, F. Morales y P. Rivilla por su ayuda con realización de las pruebas.
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Alkali-activated slag concrete: Fresh and hardened behaviour

  • Puertas, Francisca
  • González-Fonteboa, Belén
  • González-Taboada, Iris
  • Alonso López, María del Mar
  • Torres Carrasco, Manuel
  • Rojo-López, Gemma
  • Martínez-Abella, Fernando
Versión aceptada de: https://doi.org/10.1016/j.cemconcomp.2017.10.003, [Abstract:] The behaviour of fresh and hardened alkali-activated slag (AAS) and OPC concretes was compared and the effect of mixing time assessed. OPC and AAS concrete slump and rheological results proved to differ, particularly when the slag was activated with waterglass (WG). The nature of the alkaline activator was the key determinant in AAS concrete rheology. Bingham models afforded a good fit to all the OPC and AAS concretes. In OPC and NaOH-activated AAS concretes, longer mixing had an adverse effect on rheology while improving hardened performance only slightly. In WG-AAS concrete, longer mixing times, improved mechanical properties and also rheological behaviour was enhanced, in which those conditions were required to break down the microstructure. Longer mixing raised thixotropy in OPC and NaOH-activated AAS concretes, but lowered the value of this parameter in waterglass-activated slag concrete., This study was funded by the Spanish Ministry of the Economy under Projects BIA2013-47876-C2-1-P and BIA2014-58063-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Activated carbon as an alternative fuel. Effect of carbon ash on cement clinkerization

  • Husillos Rodríguez, N.
  • Martínez-Ramírez, S.
  • Blanco-Varela, María Teresa
9 págs.; 7 figs.; 10 tabs., Spent activated carbon is a by-product of potabilization plants. The present study explored the feasibility of valorizing this waste as an alternative fuel to replace oil coke in portland clinker furnaces. This involved determining its composition, calorific value, and ash and heavy metal content. Since the ash generated by spent activated carbon firing is taken up by the clinker, the possible effect of such uptake on clinkerization or the properties of the clinker obtained were also ascertained. Although spent activated carbon has an 18% lower calorific value than oil coke, one of the traditional cement kiln fuels, it was found to be apt for the purpose envisaged. Its ash content (10 wt%) is one order of magnitude higher than the ash content in coke. Spent activated carbon ash contains substantial proportions of anhydrite and quartz, hematite and augite, but consists primarily of amorphous matter (59 wt%). The effect of this ash on clinker phases was studied by clinkerizing raw meal in which it was used as a replacement for clay. Such meal exhibited high burnability and yielded clinkers with a composition and mineralogy comparable to the properties found in the industrial product. The sulfate present in the ash induced substantial alite crystal growth in the clinker. The loss of minority elements during clinkerization was likewise studied. © 2016 Elsevier Ltd. All rights reserved., This study was conducted under the leadership of Aguas de Barcelona as part of a CENIT 2007-1039 (National Strategic Consortia for Technical Research) project entitled “Technological development of a self-sustainable urban water cycle” (SOSTAQUA), funded by the Spanish Centre for Industrial Technological Development (CDTI). It has been also funded from BIA 2013-47876-C2-1-P and BIA2013- 43293-R projects., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Assessment of parameters governing the steel fiber alignment in fresh cement-based composites

  • Pérez Villar, Víctor
  • Flores Medina, Nelson
  • Alonso López, M. del Mar
  • Gismera Diez, Sara
  • Puertas, Francisca
The main aim of this paper is to measure the induced torque needed to rotate a steel fiber, hence an experimental and parametrical analysis of factors governing steel fiber alignment in cement pastes and mortar, rotating from static position and rotating in a dynamic fluid is here presented. To aim this objective, a set of rheological tests has been conducted to assess the torque necessary to rotate steel fibers immersed into different fresh cement paste and mortar mixes with Bingham fluid behaviour. Fibers of different aspect ratios (length/width) and different geometry, straight and hooked-end, have been evaluated as they are the more commonly used. On the other hand, different parameters (type of mixture, size of aggregates, volume fraction of aggregates) affecting cement mixtures are also analysed and their influence in fiber orientation discussed. Fiber alignment depends on external torques applied to fibers, immersed into a cement-water-aggregate viscous system, that can be produced during or after casting. The flowability of the fresh suspension with fibers produces a load/pressure that generates a torque that can align them. Fiber alignment is a main goal to pump the fresh material. Hence, the factors that govern fiber alignment are studied which increase the post-cracking strength of cement-based composites under load along its life service due to casting or pumping. To that end, a set of tests has been conducted to assess the torque necessary to rotate steel fibers immersed into different fresh cement paste and mortar mixes with Bingham fluid behaviour. Fibers of different aspect ratios(length/width) and different geometry (straight and hooked-end) have been evaluated. On the other hand, different parameters (type of mixture, size of aggregates, volume fraction of aggregates) affecting cement mixtures are also analysed and their influence on fiber orientation is discussed. The values obtained here are between 1 and 14 N . mm min of dynamic yield torque and 0.1 and 0.5 N . mm min for viscoplastic torque per fiber, depending on fiber geometry, are helpful to improve the fiber alignment in cement-based composites reinforced with fibers through a design and production based on these parameters., Special acknowledgment, appreciation and recognition to the IETcc-CSIC collaboration using the Viskomat™ NT rheometer within the framework of the Excellence Project MINECO BIA2013-47876-C2-1P. The authors want also acknowledge the laboratory of Materials of Architecture, Universidad Poiltécnica de Madrid., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the alkaline solution and temperature on the rheology and reactivity of alkali-activated fly ash pastes

  • Palacios, Marta
  • Alonso López, M. del Mar
  • Varga, C.
  • Puertas, Francisca
The aim of the present research is to ascertain the effect of the nature and concentration of the alkaline activator and temperature on the rheological behaviour of alkali-activated fly ash (AAFA) pastes. Furthermore, the reaction process of fly ash has been investigated from rheological measurements. Results have shown that the increase of the activator concentration and the temperature leads to an increase of yield stress and apparent viscosity, mainly at temperatures above 65 °C when dissolution of fly ash and precipitation of hydration products is raised. In general, similar activation energies were determined for alkali-activated fly ash pastes, regardless of the concentration and silica modulus of the activator, concluding that the underlying reaction mechanism is the same independently on the nature of the activating solution., Prof. F. Puertas thanks MINECO (Spanish Ministry) for funding BIA2013-47876-C2-1-P project. Dr. M. Palacios acknowledges Consejería de Educación e Investigación (Comunidad de Madrid) for funding the 2016-T1/AMB-1434 project in the frame of “Ayudas de Atracción de Talento Investigador”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Olive biomass ash as an alternative activator in geopolymer formation: A study of strength, radiology and leaching behaviour

  • Alonso López, M. del Mar
  • Gascó, C.
  • Martín Morales, M.
  • Suárez-Navarro, José Antonio
  • Zamorano, M.
  • Puertas, Francisca
Chemical, physical, mineralogical and radiological characterization of olive biomass fly ash (OBFA) and bottom ash (OBBA) was main objective to determine their potential use as alkaline activators in the preparation of alkali-activated materials or geopolymers. Water solubility tests showed that they released K and Na ions, affording a high pH and alkaline content. Pastes made with 70 wt% vitreous blast furnace slag (SL) and 30 wt% of OBFA or OBBA yielded alkali-activated materials with 28 days mechanical strength of 33 to 18 MPa. In pastes prepared with 30 wt% OBFA, strength values were comparable to those developed by slag pastes activated with a commercial KOH. However, the pastes made with 70 wt% coal fly ash and 30 wt% OBFA or OBBA proved to be inviable because the pH reached was not high enough to activate the precursor. The radiological calculations of OBFA- and OBBA-SL bearing pastes would conform to European legislation on protection against exposure to ionising radiation, for the activity concentration index (ACI) found in the final product was less than 1 in all cases. The pastes leached primarily K. The presence of elements such as 210Po and 210 Pb at the end of the decay chain in the eluates would not limit the use of biomass ash and slag blends. These findings have confirmed the feasibility of using olive oil biomass ashes as an alternative alkaline activator in blast furnace slag systems to produce alkali-activated materials or geopolymers, with properties that make them apt for use as building materials., Funding for the tests conducted in this study was provided by the Spanish Ministry of Economy, Industry and Competitiveness under projects BIA2013-47876-C2-1-P and BIA2016-77252-P., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Alkali-activated slag concrete: Fresh and hardened behaviour

  • Puertas, Francisca
  • González-Fonteboa, B.
  • González-Taboada, I.
  • Alonso López, M. del Mar
  • Torres-Carrasco, Manuel
  • Rojo, G.
  • Martínez Abella, Fernando
The behaviour of fresh and hardened alkali-activated slag (AAS) and OPC concretes was compared and the effect of mixing time assessed. OPC and AAS concrete slump and rheological results proved to differ, particularly when the slag was activated with waterglass (WG). The nature of the alkaline activator was the key determinant in AAS concrete rheology. Bingham models afforded a good fit to all the OPC and AAS concretes. In OPC and NaOH-activated AAS concretes, longer mixing had an adverse effect on rheology while improving hardened performance only slightly. In WG-AAS concrete, longer mixing times, improved mechanical properties and also rheological behaviour was enhanced, in which those conditions were required to break down the microstructure. Longer mixing raised thixotropy in OPC and NaOH-activated AAS concretes, but lowered the value of this parameter in waterglass-activated slag concrete., This study was funded by the Spanish Ministry of the Economy under Projects BIA2013-47876-C2-1-P and BIA2014-58063-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterization and hydration of cements and pastes obtained from raw mix containing Moroccan oil shale and coal waste as a raw material

  • Chhaiba, Salma
  • Blanco-Varela, María Teresa
  • Diouri, A.
  • Bougarrani, S.
In the present work, the hydration and physical properties of cements obtained from a raw mixes containing oil shale and coal waste as an alternative raw material were explored. A study of clinkers was carried out using chemical analysis and Rietveld analysis and the hydrated products were characterized by conduction calorimetry, X-ray diffraction, FTIR, Differential thermal analysis-thermal gravimetry and Scanning electron microscope. The findings showed that the cement paste containing both oil shale and coal waste had the highest compressive strength. According to the hydration studies, the four hydration steps were observed in all cements. The conduction calorimetry study showed the formation of the calcium monosulfoaluminate phase (AFm) in all cements which in cement containing coal waste was retarded by 50 h due to the high Na2O concentration in its clinker. Further, the identified hydration products: C-S-H gel, portlandite and Afm phase, which detected by XRD, FTIR and ATD/TG have been observed morphologically in SEM images. Moreover, the EDX microstructural study revealed that C-S-H gel contains a less amount of Aluminum and sulfur., This paper has been carried out as part of a CSIC-Mohammed V University of Rabat, cooperation programm (iCOOPA20067). Facilities given by IETcc (CSIC) and funding from BIA 2013-47876-C2-1-P and BIA BIA2013-43293-R projects as well as the Regional Government of Madrid Community and European Social Fund (Geomaterials Programme2 S2013/MIT-2914) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microcalorimetric study of the effect of calcium hydroxide and temperature on the alkaline activation of coal fly ash

  • Hoyos-Montilla, Ary A.
  • Puertas, Francisca
  • Tobón, Jorge I.
The objective of this research is to know, through the flow of heat released, the effect of the addition of calcium hydroxide and the temperature on the alkaline activation of coal fly ash with a solution of sodium hydroxide. The heat flow of the samples was measured from an isothermal conduction microcalorimeter at 25, 35 and 45 °C, with percentages of calcium hydroxide between 5 and 15 mass% and concentrations of sodium hydroxide between 6 and 10 M. The data obtained were analyzed by the ANOVA technique using a response surface. Calcium hydroxide mainly supplies nucleation sites and increases the rate of reaction during the latent period. Sodium hydroxide increases the degree of reaction, the amount and rate of the reactions up to concentrations of 10 M. The time of the wetting and dissolving processes was 6 min, independent of the temperature and composition of the mixture. The maximum amount of energy released was 200 kJ kg−1, seeking to be minimal in the initial processes and maximum in the end. The calculated apparent activation energy was 361.20 ± 16.47 kJ mol−1 which reflects the importance of the temperature in the alkaline activation processes. The temperature does not significantly affect the amount of energy released, but does affect the rate and number of reactions., The authors thank the Administrative Department of Science, Technology and Innovation of Colombia (Colciencias) for the support of this study through the National Call 567 for Doctoral Studies in Colombia. Likewise, they thank the Ministry of Economy, Industry and Competitiveness of Spain for the project grant BIA2013-47876-C2-1-P, within which a part of the tests of this study was carried out., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Moroccan oil shale and coal waste as alternative raw materials in Portland cement clinker manufacture. Clinkerisation reactions and clinker characterisation, Esquistos bituminosos como materia prima alternative en la fabricación de clínker de cemento Portland. Reacciones de clinkerización y caracterización del clínker.

  • Chhaiba, Salma
  • Blanco-Varela, María Teresa
  • Diouri, A.
[EN]: For some time the cement industry has been seeking procedures to effectively lower the higher energy costs involved in cement manufacture. Timahdit oil shale and Jerada coal waste could potentially be used as alternative raw materials to produce clinker. This study explored the possibility of applying those materials to a greener use, based on the reactivity and burnability of raw mixes containing Moroccan oil shale and coal waste. The findings showed that, irrespective of particle size, oil shale mixes delivered higher reactivity than coal waste materials, although reactivity was highest in the oil shale clinker with a particle size < 45 μm. The clinkers bearing oil shale with a particle size < 90 μm or a blend of oil shale and coal waste with a size < 45 μm contained higher proportions of alite ( > 70 %)., [ES]: La industria cementerabusca desde hace algún tiempo procedimientos que reduzcan el alto consumo de energía de la producción de cemento. La pizarra bituminosa de Timahdit (BOS) y los desechos de carbón de Jerada (CW) se pueden utilizar potencialmente como materiales alternativos en la fabricación de clinker. Este estudio se enfoca en evaluar esta posibilidad, valorizar dichos materiales y considerar un uso más ecológico para ellos. Exploramos la reactividad y la aptitud a la cocción de mezclas crudas de clínker que contienen BOS o CW. La reactividad de los crudos que contienen BOS es mejor que la de los que contienen CW, independientemente de su tamaño de partícula, siendo el que contiene BOS con un tamaño de partícula <45 μm, la más reactiva. Los clínkeres que contienen BOS o la mezcla de BOS y CW (tamaño de partícula <90 μm y 45 μm respectivamente) contienen proporciones de alita >70%., This paper has been carried out as part of a CSIC-Mohammed V University of Rabat, cooperation programm (i-COOPA20067). Facilities given by IETcc (CSIC) and funding from BIA 2013-47876-C2-1-P and BIA BIA2013-43293-R projects as well as the Regional Government of Madrid Community and European Social Fund (Geomaterials Programme2 S2013/MIT-2914) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Radioactivity and Pb and Ni immobilization in SCM-bearing alkali-activated matrices

  • Alonso López, M. del Mar
  • Pasko, A.
  • Gascó, C.
  • Suárez-Navarro, José Antonio
  • Kovalchuk, G.
  • Krivenko, Pavel V.
  • Puertas, Francisca
Partial or total replacement of Portland cement clinker by SCMs (Supplementary Cementitious Materials) is a priority for the cement industry in its pursuit of global sustainable development and eco-friendly binder manufacture. The most widely used SCMs include industrial by-products such as blast furnace slag, fly ash and red mud. Alkali-activated cements manufactured with SCMs may reduce the need for Portland clinker by up to 90 wt%–100 wt% with no significant decline in material strength. The trade-off, however, is the risk of higher than legally allowable levels of radioactivity and unbound heavy metals (Cd, Hg, Ni, Pb, Cr), which may leach into the soil with the concomitant adverse implications for human health and the environment. This study assessed the mechanical strength, leachability and natural radioactivity of alkali-activated cement paste containing industrial waste-based SCMs (blast furnace slag, fly ash and red mud) and Pb and Ni compounds. Strength was highest in alkali-activated slag and slag/fly ash pastes and lowest in the red mud-containing materials. The addition of Pb or Ni sulphates had no adverse effect on this parameter. Alkaline and OPC pastes showed a high level of immobilization of both lead and nickel ions. According to the radiological findings, the Activity Concentration Index (I) was higher in red mud than in OPC, blast furnace slag or fly ash. With (I) values lower than 1, however, all the hydrated/activated materials studied would be EU directive-compliant. Nonetheless, the use of these new materials will depend not only on the activity concentration index, but also on their physical and chemical properties and the quality tests that must be passed to conform to legal requirements., Anton Pasko worked at the Eduardo Torroja Institute (IETcc-CSIC) under a short-term (2016) scientific mission (STSM) obtained through the institute and sponsored by COST Action TU 1301 (NORM4Building). The authors thanks also to Spanish Ministry of Economy, Industry and Competitiveness for funding the BIA2013-47876-C2-1-P and BIA2016-77252-P, where tests of this study were conducted., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Viability of the use of construction and demolition waste aggregates in alkali-activated mortars, Utilización de áridos procedentes de residuos de construcción y demolición en morteros activados alcalinamente

  • Alonso López, M. del Mar
  • Rodríguez, A.
  • Puertas, Francisca
[EN]: This study explores the technological feasibility of using construction and demolition waste (C&DW) as recycled aggregate in alkali activated mortars, ascertaining the mechanical and microstructural behavior. Shrinkage behavior of alkali activated slag mortars (AAS) and fire resistance of alkali activated fly ash (AAFA) incorporating recycled aggregates have been also tested Normalized siliceous sand and two types of recycled concrete aggregates were used in the mixes at different proportions. The findings showed that water demand was higher in mortars prepared with recycled aggregate. Partial replacement (20% - 80/20) of conventional aggregate with the recycled material was also observed to yield mortars with high mechanical strength, although total porosity also rose. Total replaclement, gave worse mechanical performance however. Fire resistance and shrinkage studies conducted indicated that alkaline cement mortars prepared with 80/20 recycled aggregated exhibit acceptable performance., [ES]: Este estudio explora la viabilidad tecnológica del uso de residuos de construcción y demolición (C & DW) como árido reciclado en morteros activados alcalinamente, determinando el comportamiento mecánico y microestructural. Asimismo, se determinó la retracción sufrida por morteros de escoria activados alcalinamente (AAS) y la resistencia al fuego de morteros de cenizas volantes activadas alcalinamente (AAFA) con incorporación de estos áridos reciclado. Se utilizó arena silícea normalizada y dos tipos de áridos de hormigón reciclado en diferentes proporciones. Los resultados mostraron que la demanda de agua era más alta en los morteros preparados con árido reciclado. También se observó que el reemplazo parcial con un 20% (80/20) del árido convencional con el material reciclado producía morteros con alta resistencia mecánica, aunque la porosidad total también aumentaba. El reemplazo total, sin embargo, dio peor rendimiento mecánico. Los estudios de resistencia al fuego y retracción realizados, indicaron que los morteros de cementos activados alcalinamente preparados con áridos reciclados en proporción 80/20 presentan un rendimiento aceptable., This research was funded by the Spanish Ministry of the Economy under project BIA2013-47876-C2-1-P., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Influencia de la naturaleza y granulometría de los áridos en el comportamiento reológico de morteros de cementos activados alcalinamente

  • Gismera Diez, Sara
  • Alonso López, M. del Mar
  • Puertas, Francisca
Trabajo presentado al V Congreso Iberoamericano de Hormigón Autocompactable y Hormigones Especiales (HAC), celebrado en Valencia (España) del 5 al 6 de marzo de 2018., El objetivo de este trabajo es profundizar en el conocimiento del comportamiento reologico de morteros de cementos activados alcalinamente (Alkali-Activated Materials, AAMs), determinando el efecto del diámetro máximo del árido y su naturaleza (silíceo, calizo y árido reciclado). Morteros de OPC se utilizan de referencia. Se realizaron ensayos de fluidez y de Stress Growth Test; también se determinaron los parámetros reológicos por el ensayo de curva de flujo. Los morteros de AAMs son más sensible que los de OPC a la variación del diámetro máximo de los áridos; aunque no se han observado diferentes comportamientos asociados a la naturaleza del mismo. Se ha demostrado que todos los morteros se ajustan al modelo reológico de Bingham, independientemente del diámetro máximo de los áridos y de la naturaleza de los mismos., Este estudio fue financiado por el Ministerio de Economía (MINECO) bajo el Proyecto del plan Nacional BIA2013-47876-C2-1-P. Los autores desean agradecer a A. Gil, F. Morales y P. Rivilla por su ayuda con realización de las pruebas.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Early reactivity of sodium silicate-activated slag pastes and its impact on rheological properties

  • Palacios, Marta
  • Gismera Diez, Sara
  • Alonso López, M. del Mar
  • d´Espinose Lacaillerie, J.B.
  • Lothenbach, Barbara
  • Favier, Aurelie
  • Brumaud, Coralie
  • Puertas, Francisca
The fast loss of fluidity of sodium silicate-activated slag (SS-AAS) systems have been widely studied in the literature. In this study, the rheology of these cements has been correlated with the evolution of the reaction products formed over time. For this purpose, a combination of experimental characterization techniques, to study the pore solution composition and microstructure of SS-AAS pastes and hermodynamic calculations have been applied. The initial precipitation of ill-defined N-A-S-H and C-N-A-S-H producta leads to a fast increase of the storage modulus after 40 min of reaction. These products are formed from the reaction of the Na+ ions and silicate ions of the activator with the Ca2+ and aluminate species dissolved from the slag. However, when a shear is applied, the structure breaks down and fluidity is recovered, that infers that the attractive forces between the particles are low at the early stages of hydration., The authors thank Prof. Habert (ETHZ) for constructive discussion. Dr. Francesco Caruso (SIK-ISEA) is thanked for helping to develop a protocol for the ICP-OES measurements. Dr. M. Palacios acknowledges Consejería de Educación e Investigación (Comunidad de Madrid) for funding the 2016-T1/AMB-1434 project in the frame of “Ayudas de Atracción de Talento Investigador” and MCIU/AEI/FEDER, UE for funding the RTI2018-099326-A-I00 project. Prof. F. Puertas thanks the Spanish Ministry of Science and Innovation for funding BIA2013-47876-C2-1-P and BIA2016-77252-P projects., Peer reviewed