Pasar al contenido principal

CEMENTOS Y HORMIGONES PREPARADOS CON RESIDUOS NORM (NATURALLY OCCURRING RADIOACTIVE MATERIAL). COMPORTAMIENTO, PROPIEDADES Y CARACTERIZACION RADIOLOGICA

BIA2016-77252-P

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2016
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Olive biomass ash as an alternative activator in geopolymer formation: A study of strength, radiology and leaching behaviour

  • Alonso López, M. del Mar
  • Gascó, C.
  • Martín Morales, M.
  • Suárez-Navarro, José Antonio
  • Zamorano, M.
  • Puertas, Francisca
Chemical, physical, mineralogical and radiological characterization of olive biomass fly ash (OBFA) and bottom ash (OBBA) was main objective to determine their potential use as alkaline activators in the preparation of alkali-activated materials or geopolymers. Water solubility tests showed that they released K and Na ions, affording a high pH and alkaline content. Pastes made with 70 wt% vitreous blast furnace slag (SL) and 30 wt% of OBFA or OBBA yielded alkali-activated materials with 28 days mechanical strength of 33 to 18 MPa. In pastes prepared with 30 wt% OBFA, strength values were comparable to those developed by slag pastes activated with a commercial KOH. However, the pastes made with 70 wt% coal fly ash and 30 wt% OBFA or OBBA proved to be inviable because the pH reached was not high enough to activate the precursor. The radiological calculations of OBFA- and OBBA-SL bearing pastes would conform to European legislation on protection against exposure to ionising radiation, for the activity concentration index (ACI) found in the final product was less than 1 in all cases. The pastes leached primarily K. The presence of elements such as 210Po and 210 Pb at the end of the decay chain in the eluates would not limit the use of biomass ash and slag blends. These findings have confirmed the feasibility of using olive oil biomass ashes as an alternative alkaline activator in blast furnace slag systems to produce alkali-activated materials or geopolymers, with properties that make them apt for use as building materials., Funding for the tests conducted in this study was provided by the Spanish Ministry of Economy, Industry and Competitiveness under projects BIA2013-47876-C2-1-P and BIA2016-77252-P., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Radiological behaviour of pigments and water repellents in cement-based mortars

  • Suárez-Navarro, José Antonio
  • Lanzón, M.
  • Moreno de los Reyes, A.M.
  • Gascó, C.
  • Alonso López, M. del Mar
  • Blanco-Varela, María Teresa
  • Puertas, Francisca
The use of admixtures in mortars to improve both their physical-chemical and ornamental features has become increasingly common in recent years. The varying origin and composition of these products, some sourced from waste produced in other industries, poses the question of whether they modify the activity concentration index (ACI) of the construction materials to which they are added. Seven pigments, some of natural and others of artificial origin, and two water repellents were characterised both chemically and radiologically in this study. Neither the synthetic pigments nor the water repellents exhibited significant radiological content. The pigments based on Fe2O3 of natural origin had detectable activity concentrations of naturally occurring radionuclides from the 238U series. Those levels were attributable to the raw material used, namely the bauxite red mud generated in aluminium production. In addition to Si, Al, Fe, Ca, Ti and Na as majority elements, this sludge also contains traces of K, Cr, V, Ba, Cu, Mn, Pb, Zn, P, F, S and As, among others, including naturally occurring uranium. The public and occupational radiological risk due to exposure to pigment-modified construction materials were consequently assessed. Neither the doses for the public at large and for workers were found neither to be significant nor constitute any perceptible hazard, essentially in light of the small amounts of pigment used to prepare mortars., This study was funded by the Spanish Ministry of the Economy, Industry and Competitiveness under project BIA2016-77252-P., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Natural radioactivity of Portland cement mortars made with granite sand

  • Sanjuán, Miguel Ángel
  • Argiz, Cristina
  • Alonso López, M. del Mar
  • Suárez-Navarro, José Antonio
  • Gascó, C.
  • Puertas, Francisca
Póster presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., Granites are rocks formed primarily by the minerals quartz, feldspar and mica, but they also contain varying amounts of natural uranium (238U) and thorium, which are a source of natural radioactivity. In Spain, certain areas of the Sierra de Madrid and the Galician area are rich in this type of rocks, which are used not only as stones in construction, but also as aggregates in the preparation of mortars and concretes. Directive 2013/59 / EURATOM establishes the limits of natural radioactivity that come from building materials. Therefore, given the uranium content of the granites, their radiological control addresses special importance. In the present study we have studied natural radioactivity of Portland cement mortars made with granite sand. For this purpose, three granitic aggregates of different origin have been characterized chemically, mineralogically and petrologically. The natural radioactivity of the three granitic aggregates with three different granulometry has been determined through gamma spectrometry. Likewise, OPC mortars have been prepared with the fine fractions of granitic aggregates (<4 mm) establishing both the activity indexes of these mortars and their relationship with the chemistry and mineralogy of granitic aggregates. As a general result, it is observed that the radioactivity indexes of each of the components additively affect the overall radioactivity of the Portland cement mortar., The authors wish to thank to Spanish Ministry of Science, Innovation and Universities for funding the BIA2016-77252-P (AEI/FEDER, UE), where tests of this study were conducted.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Radioactivity and Pb and Ni immobilization in SCM-bearing alkali-activated matrices

  • Alonso López, M. del Mar
  • Pasko, A.
  • Gascó, C.
  • Suárez-Navarro, José Antonio
  • Kovalchuk, G.
  • Krivenko, Pavel V.
  • Puertas, Francisca
Partial or total replacement of Portland cement clinker by SCMs (Supplementary Cementitious Materials) is a priority for the cement industry in its pursuit of global sustainable development and eco-friendly binder manufacture. The most widely used SCMs include industrial by-products such as blast furnace slag, fly ash and red mud. Alkali-activated cements manufactured with SCMs may reduce the need for Portland clinker by up to 90 wt%–100 wt% with no significant decline in material strength. The trade-off, however, is the risk of higher than legally allowable levels of radioactivity and unbound heavy metals (Cd, Hg, Ni, Pb, Cr), which may leach into the soil with the concomitant adverse implications for human health and the environment. This study assessed the mechanical strength, leachability and natural radioactivity of alkali-activated cement paste containing industrial waste-based SCMs (blast furnace slag, fly ash and red mud) and Pb and Ni compounds. Strength was highest in alkali-activated slag and slag/fly ash pastes and lowest in the red mud-containing materials. The addition of Pb or Ni sulphates had no adverse effect on this parameter. Alkaline and OPC pastes showed a high level of immobilization of both lead and nickel ions. According to the radiological findings, the Activity Concentration Index (I) was higher in red mud than in OPC, blast furnace slag or fly ash. With (I) values lower than 1, however, all the hydrated/activated materials studied would be EU directive-compliant. Nonetheless, the use of these new materials will depend not only on the activity concentration index, but also on their physical and chemical properties and the quality tests that must be passed to conform to legal requirements., Anton Pasko worked at the Eduardo Torroja Institute (IETcc-CSIC) under a short-term (2016) scientific mission (STSM) obtained through the institute and sponsored by COST Action TU 1301 (NORM4Building). The authors thanks also to Spanish Ministry of Economy, Industry and Competitiveness for funding the BIA2013-47876-C2-1-P and BIA2016-77252-P, where tests of this study were conducted., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Use of Genie 2000 and Excel VBA to correct for γ-ray interference in the determination of NORM building material activity concentrations

  • Suárez-Navarro, José Antonio
  • Gascó, C.
  • Alonso López, M. del Mar
  • Blanco-Varela, María Teresa
  • Lanzón, M.
  • Puertas, Francisca
The γ-radiation emitted by building materials is calculated from the activity indices for 232Th, 226Ra and 40K and expressed as the activity concentration index (ACI). Gamma spectroscopy is a non-destructive technique frequently used to simultaneously determine the indices for several radionuclides. Spectral interpretation poses a number of challenges, including identification of γ-lines subject to summing-in effects, interference from other γ-ray emitting radionuclides and the time required to reach secular equilibrium. These challenges are not fully addressed by Canberra Industries’ Genie 2000, the software used by many laboratories to analyse samples. This article describes a Microsoft Excel workbook that exploits Genie 2000 flexibility to program applications with Visual Basic using Canberra's Nuclear Data Access Library and batch procedure tools. The workbook determines 40K activity concentration after correcting for 228Ac interference and 226Ra activity directly from the γ-peak at 186.5 keV. The method proposed was tested by participating in 13 national and international scale inter-comparison exercises. The results were statistically indistinguishable from the reference values at a coverage factor of k = 3 and no statistically significant differences were identified between the respective means by a Student's t pairwise comparison., This study was funded by the Spanish Ministry of the Economy, Industry and Competitiveness under project BIA2016-77252-P., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characteristic limits of 230Th in alpha spectrometry with 229Th as tracer, calculated by simulating interfering tails and overlapping peaks

  • Gascó, C.
  • Suárez-Navarro, José Antonio
  • Escareño-Juárez, E.
  • Fernández, E.
  • García, L.
  • Puertas, Francisca
  • Alonso López, M. del Mar
  • Pérez, C.
This study explores the effect of 229Th tracer tail interference on the determination of the sensitivity of 230Th alpha spectrometry of samples with environmental levels of radioactivity. Tracer peak tail interference was calculated with Suma-Alpha, whilst Visual Basic for Applications (VBA in Excel©) software was used to study the variation in sensitivity in terms of the amount of tracer added. Unnecessary increases in the amount of tracer or extended sample measuring times were observed to have adverse effects on method sensitivity (Detection Limit- Ld)., This study was funded by the Spanish Ministry of the Economy, Industry and Competitiveness under project BIA2016-77252-P, ‘Cementos y hormigones preparados con residuos NORM: Comportamiento, Propiedades y Caracterización Radiológica (CHARM)’. Lara García is employed as laboratory technician at CIEMAT's Department of Environmental Radioactivity and Radiological Surveillance (RAYVR) further to research contract CAM-PEJ16/AMB/TL-1459 funded by the Region of Madrid. The authors wish to thank the University of Valladolid and especially Dr Rafael Pardo for their support in the CIEMAT-University of Zacatecas partnership, and the Carolina Foundation for sponsoring Edmundo Escareño's PhD. studies at the University of Valladolid and CIEMAT, Spain., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Gamma spectrometry and LabSOCS-calculated efficiency in the radiological characterisation of quadrangular and cubic specimens of hardened portland cement paste

  • Suárez-Navarro, José Antonio
  • Moreno de los Reyes, A.M.
  • Gascó, C.
  • Alonso López, M. del Mar
  • Puertas, Francisca
Pursuant to European Directive 2013/59, materials additioned with NORM waste must be characterised radiologically to determine their acceptability for use in construction. The radionuclides studied to judge that acceptability, 232Th, 226Ra and 40K, are normally measured with gamma spectrometry. Gamma detectors are calibrated by using standards as similar as possible in dimensions and chemical composition as the matrix in the samples to be measured. In light of the broad spectrum of chemical and physical characteristics of NORM samples, experimental calibration is often beyond the means of gamma spectrometry laboratories. As a result, Monte Carlo-based methods are deployed to simulate the experimental setup consisting in detector and sample, both geometrically and chemically. Canberra Industries’ LabSOCS (Laboratory Sourceless Calibration Software) is one of the tools available for such calculations. This study verified the accuracy and precision of the counting efficiency delivered by LabSOCS, both with the standard powder geometry and a new geometry consisting in a 5 cm cubic specimen of Portland cement paste. The findings showed that in both geometries the accuracy and precision of LabSOCS-calculated efficiency (by specimen height and activity), across an energy range from 45.64 keV (210Pb) to 1460.82 keV (40K) met the acceptability criteria routinely applied in environmental radioactivity laboratories. The geometry proposed yielded activity values for the end construction material closer to the true indices than the conventional method consisting in summing the partial activities of the unreacted components., This study was funded by the Spanish Ministry of Science, Innovation and Universities' Research Agency and the European Regional Development Fund (AEI/ERDF/EU) under project BIA2016-77252-P. Author Ana María Moreno de los Reyes participated in the study under Spanish Research Agency pre-doctoral grant BES-2017-081306., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

New Approach for the Determination of Radiological Parameters on Hardened Cement Pastes with Coal Fly Ash

  • Moreno de los Reyes, A.M.
  • Suárez-Navarro, José Antonio
  • Alonso López, M. del Mar
  • Gascó, C.
  • Sobrados, Isabel
  • Puertas, Francisca
Supplementary cementitious materials (SCMs) in industrial waste and by-products are routinely used to mitigate the adverse environmental effects of, and lower the energy consumption associated with, ordinary Portland cement (OPC) manufacture. Many such SCMs, such as type F coal fly ash (FA), are naturally occurring radioactive materials (NORMs). <sup>226</sup>Ra, <sup>232</sup>Th and <sup>40</sup>K radionuclide activity concentration, information needed to determine what is known as the gamma-ray activity concentration index (ACI), is normally collected from ground cement samples. The present study aims to validate a new method for calculating the ACI from measurements made on unground 5 cm cubic specimens. Mechanical, mineralogical and radiological characterisation of 28-day OPC + FA pastes (bearing up to 30 wt % FA) were characterised to determine their mechanical, mineralogical and radiological properties. The activity concentrations found for <sup>226</sup>Ra, <sup>212</sup>Pb, <sup>232</sup>Th and <sup>40</sup>K in hardened, intact 5 cm cubic specimens were also statistically equal to the theoretically calculated values and to the same materials when ground to a powder. These findings consequently validated the new method. The possibility of determining the activity concentrations needed to establish the ACI for cement-based materials on unground samples introduces a new field of radiological research on actual cement, mortar and concrete materials., This study was funded by the Spanish Minister Science and Innovation and Spanish State Investigation Agency and the European Regional Development Fund (AEI/FEDER/EU) under research project BIA2016-77252-P. Ana María Moreno de los Reyes participated in the study under Spanish Research Agency pre-doctoral grant BES-2017-081306., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Data on natural radionuclide’s activity concentration of cement-based materials

  • Alonso López, M. del Mar
  • Moreno de los Reyes, A.M.
  • Blanco-Varela, María Teresa
  • Puertas, Francisca
Cement based materials may contain varying levels of radionuclides, mainly 226Ra (from the 238U series), 232Th and 40K, which are used to determine the Activity Concentration Index ("ACI"). According to the European directive Euratom 2013/59 in these materials, the “ACI” must be < 1 to be suitable for their use in construction. In this paper, data on the activity concentration of natural radionuclides in cement-based materials (i.e. cements, additions, pigments and aggregates) as well as their chemical composition are presented. Radioactivity measurements have been determined by using gamma spectroscopy the chemical compositions have been determined by X-Ray Fluorescence. Data for cements measured shown that white cements present a lower concentration of activity than conventional CEM I. In addition, the CAC (Calcium aluminate cements) present high activity concentration in the 232Th series. Regarding additions, FA (Fly Ash) are those that present the highest concentration of activity in the 238U and 232Th series, while olive biomass ashes are those supplementary cementitious materials that show the highest concentration of activity for 40K. Some pigments used in mortar and concrete technology were also characterized. Granitic and volcanic rocks, potentially used as aggregates present much higher activity concentration than the siliceous aggregate., This study was funded by the Spanish Ministry of the Economy, Industry and Competitiveness under project BIA2016-77252-P. Dr. M.M. Alonso also wishes to thank CSIC for funding the project PIE 2018 60I 054 (Proyecto Intramural de Incorporación)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Construcción sostenible. El papel de los materiales

  • Puertas, Francisca
  • Alonso López, M. del Mar
  • Palacios, Marta
En este artículo se aborda, de manera resumida, la necesidad de alcanzar una construcción sostenible y el papel que juegan los materiales (cemento y hormigón) para lógralo. Se describen algunas de las investigaciones que se están realizando para la obtención de cementos más eco-eficientes (cementos con bajos contenidos en clínker y cementos alcalinos). Las materias primas de gran parte de estos cementos y hormigones eco-eficientes son residuos o subproductos industriales. Se resalta la necesidad de tener controles químicos, físicos, mineralógicos y radiológicos de estos residuos antes y después de su utilización en la preparación de los materiales de construcción. Se describen brevemente los aspectos (prestacionales y medioambientales) positivos de estos cementos y las líneas de investigación abiertas en torno a la mejora de sus propiedades y comportamiento. Con esa misma finalidad de alcanzar el “Hormigón Verde” se presentan resultados de la reutilización de residuos de construcción y demolición en la producción de hormigón. Se hace también referencia a otros tipos de hormigones de altas prestaciones (resistentes y durables) y propiedades y características especiales (auto-sellantes, auto-limpiables, impresión 3D, etc.)., Las autoras agradecen a la Agencia Estatal de Investigación y al Ministerio de Ciencia e Innovación la subvención del Proyecto BIA2016-77252-P y y RTI2018-099326-A-I00. Así mismo, las autoras agradecen a la Consejería de Educación e Investigación de la Comunidad de Madrid por la concesión de las ayudas de atracción de talento investigador 2016-T1/AMB-1434., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural, mechanical and radiological characterization of mortars made with granite sand

  • Puertas, Francisca
  • Suárez-Navarro, José Antonio
  • Gil-Maroto, A.
  • Moreno de los Reyes, A.M.
  • Gascó, Catalina
  • Pachón Montaño, Alicia
  • Alonso López, M. del Mar
The study reported the effect of granite sand on strength and microstructural developments in mortars prepare from OPC with a high coal fly ash (FA) content or from hybrid alkaline cements. The radiological behaviour of the resulting mortars was compared to materials prepared with siliceous sand (with particles sizes of <2 mm) and the relationship between such radiological findings and mortar microstructure and strength was explored. A new method for determining natural radionuclides and their activity concentration Index (ACI) on cement mortars (specifically to solid 5-cm cubic specimens) was applied and validated. The microstructural changes associated in mortars have no effect on mortar radiological content measurements. The mortars with granite sand exhibited very high ACI > 0.96, which would ultimately limit their use. A conclusion of interest is that where information is at hand on the starting materials (OPC, FA, sand, admixtures), their pro-portions in the mortar and the mixing liquid content (water or alkaline activators) their radiological content is accurately predicted. The inference is that a mortar’s radiological content and ACI can be known prior to mixing, providing a criterion for determining its viability. That in turn lowers environmental risks and the health hazards for people in contact with such materials., This study was funded by the Spanish Ministry of Science and Innovation as well as by the National Research Agency in conjunction with the European Regional Development Fund (AEI/ERDF/EU) under research project BIA2016-77252-P. Ana María Moreno de los Reyes participated in the study under National Research Agency pre-doctoral grant BES-2017-081306. M.M. Alonso also wishes to thank CSIC for funding the project PIE 2018 60I 054., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hybrid Cements: Mechanical Properties, Microstructure and Radiological Behavior

  • Moreno de los Reyes, A.M.
  • Suárez-Navarro, José Antonio
  • Alonso López, M. del Mar
  • Gascó, Catalina
  • Sobrados, Isabel
  • Puertas, Francisca
The use of more eco-efficient cements in concretes is one of the keys to ensuring construction industry sustainability. Such eco-efficient binders often contain large but variable proportions of industrial waste or by-products in their composition, many of which may be naturally occurring radioactive materials (NORMs). This study explored the application of a new gamma spectrometric method for measuring radionuclide activity in hybrid alkali-activated cements from solid 5 cm cubic specimens rather than powder samples. The research involved assessing the effect of significant variables such as the nature of the alkaline activator, reaction time and curing conditions to relate the microstructures identified to the radiological behavior observed. The findings showed that varying the inputs generated pastes with similar reaction products (C-S-H, C-A-S-H and (N,C)-A-S-H) but different microstructures. The new gamma spectrometric method for measuring radioactivity in solid 5 cm cubic specimens in alkaline pastes was found to be valid. The variables involved in hybrid cement activation were shown to have no impact on specimen radioactive content. The powder samples, however, emanated Rn (a descendent of Ra), possibly due to the deformation taking place in fly ash structure during alkaline activation. Further research would be required to explain that finding., Funding: This study was funded by the Spanish Ministry of Science and Innovation and the country’s National Research Agency, as well as the European Regional Development Fund (AEI/FEDER/EU) under research projects BIA2016-77252-P and PID2020-116002RB-I00, Ana María Moreno de los Reyes participated in the study under pre-doctoral grant BES-2017-081306 awarded by the National Research Agency., Peer reviewed