Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Evolution of the microstructure and mechanical properties of zirconia-based composites sintered by microwave technology

  • Bonilla-Molina, Ashley
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Moreno, Rodrigo
[EN] This work aims to produce zirconia-based materials by microwave sintering process for dental and prosthetic applications. Two compositions were evaluated: alumina-toughened-zirconia with 25 wt.% Al2O3, stabilized with 10.5 wt.%(Ce, Y), and yttria-stabilized-zirconia (5.4 wt.% Y2O3). The microstructural evolution and its influence on their mechanical properties were analyzed. The composites were sintered by conventional sintering at 1400 and 1500 ¿C with 2 h dwelling, and by microwave sintering at 1200 and 1300 ¿C with 10- and 15-min dwell times, resulting in fully densified ceramics. Relative densities are > 97% and HV higher than 11 GPa for all compositions and sintering conditions. The FESEM images confirm the formation of platelets at higher temperatures, which results in an increase in fracture toughness from 5.0 to 8.2 MPa¿m1/2. The low-thermal-degradation indicates that the composite performs well and that the tetragonal-to-monoclinic transformation is absent after 40 h of ageing, making this material suitable for dental and prosthetic applications., This publication is part of the grant CNS2023 144190 funded by MICIU/AEI/ 10.13039/501,100,011,033 and by the European Union NextGenerationEU/PRTR . CIGRIS/2022/077 and CIAICO/2023/264 projects funded by Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of calcination rate on mechano-chemically activated powders for the synthesis of lead-free KNN-type ceramics

  • Bonilla-Molina, Ashley
  • Pruna, Alina Iuliana|||0000-0002-5250-066X
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Fernández-González, Daniel
[EN] Given the raising environmental concerns over lead toxicity, replacing the common leadbased piezoelectric ceramics with a proper alternative became a hot topic. (Na0.5K0.5)NbO3 (KNN) is considered a potential replacement for such ceramics. This work presents the synthesis of KNN-type ceramics based on conventional solid-state reaction, where the effect of precursor particle size is studied. A combined mechanical activation by ball milling and calcination at low temperature of 800 ¿C is applied. The phase structure evolution, morphology and mechanical properties are investigated systematically with the particle size and the calcination rate. The results indicate a marked effect of the precursor particle size on the properties of obtained ceramics. Secondary phase content could be lowered and tetragonality improved by the applied approach. Despite the presence of secondary phases, dielectric measurements indicated typical values of dielectric constant and loss for piezoelectric materials., This publication is part of the grant PID2021-128548OBC21 & C22 funded by MICIU/AEI/10.13039/501100011033 and by ERDF/EU , and the grant CNS2023-144190 funded by MICIU/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR . CIGRIS/2022/077 project funded by Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Role of electric and magnetic fields in the densification and grain growth of CaMnO3 perovskite sintered by microwave

  • Martins Mansano Rosa , João Paulo
  • Borges da Hora, Lara Cristina
  • Thomazini, Daniel
  • Gelfuso, Maria Virginia
  • Penaranda-Foix, Felipe L.|||0000-0003-4012-0763
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] This study investigates how electric and/or magnetic fields influence the densification and microstructural evolution of microwave-sintered CaMnO3 (CMO) thermoelectric ceramics. Experiments used a maximum magnetic field microwave configuration (H-MW) from 900 °C to 1300 °C at various dwell times. Temperature and dwell time strongly influenced both densification and grain growth. Optimal densification (~90% relative density) occurred at 1300 °C for 15¿min. Longer dwell times reduced final density due to abnormal grain growth. Furthermore, grain growth mechanisms transitioned with temperature from grain boundary (n= 4) to lattice diffusion (n = 3), with activation energy increasing with dwell time, due to marokite consumption into the sintering process. Overall, the H-MW configuration enables efficient densification and microstructural control, demonstrating its effectiveness in tailoring CMO sintering kinetics for thermoelectric applications., This publication is part of the grants CNS2023-144190 funded by MICIU/AEI/10.13039/501100011033, "ERDF/EU" and the "European Union NextGenerationEU/PRTR", and Generalitat Valenciana of the grant CIAICO/2023/264. To National Council for Scientific and Technological Development of Brazil (CNPq-Grant (316730/2023-8) and Minas Gerais State Foundation of Support to the Research (FAPEMIG-Grant APQ-01856-22) for the financial grant. Joao Paulo Martins Mansano Rosa gratefully acknowledges the financial support of a doctoral fellowship provided by the Coordination for the Improvement of Higher Level or Education-Personnel (CAPES), under Grant No 23038.003930/2024-79.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microwave-Driven Densification of NASICON-type LATP: A Fast Route Toward Efficient Solid-State Electrolytes

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
[EN] The transition from flammable liquid electrolytes to safer solid-state electrolytes is essential for next-generation batteries. Li1.3Al0.3Ti1.7(PO4)3 (LATP) is a promising NASICON-type electrolyte, but its application is hindered by energy-intensive high-temperature sintering. This work demonstrates microwave sintering as a rapid and efficient route to fabricate dense, highly conductive LATP. Green bodies with a relative density of 71% were obtained by combined uniaxial and isostatic pressing, followed by microwave sintering between 800 and 1100 ºC for only 10 minutes. Optimal densification (91.4%) was achieved at 1000 ºC, while higher temperatures led to abnormal grain growth and rutile-TiO2 formation. Electrochemical impedance spectroscopy revealed a strong reduction in grain-boundary resistance above 950 ºC. LATP sintered at 1000 ºC exhibited an ionic conductivity of 5·10-4 S cm-1 and an activation energy of 0.20 eV. Symmetric Li|LATP|Li cells showed stable cycling over 500 h with low overpotentials, confirming excellent transport and mechanical integrity., This publication is part of the grants PID2021-128548OB-C21 & C22 and CNS2023-144190 funded by MICIU/AEI/10.13039/501100011033, "ERDF/EU" and the "European Union NextGenerationEU/PRTR". A.M.-S. acknowledges the funding from the Aid for Early Research Projects (PAID-06-25) and the postdoctoral fellowship (PAID-10-24) programs from the Vice-Rectorate for Research of Universitat Politecnica de Valencia. S.F.-N thanks Generalitat Valenciana through FPI Fellowship Program (CIACIF/2021/050) . N. V.-A. acknowledges support for the research from Universitat Jaume I under the project number UJI/2023/016. Authors thank Felipe L. Penaranda-Foix from ITACA facilities for performing the dielectric measurements.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of calcination rate on mechano-chemically activated powders for the synthesis of lead-free KNN-type ceramics, Efecto de la calcinación y de la activación mecanoquímica para obtener cerámicas sin plomo basadas en KNN

  • Bonilla, Ashley
  • Pruna, Alina
  • Benavente, Rut
  • Salvador, M. D.
  • Busquets-Mataix, David
  • Fernández-González, Daniel
  • Borrell, Amparo
[EN] Given the raising environmental concerns over lead toxicity, replacing the common lead-based piezoelectric ceramics with a proper alternative became a hot topic. (Na0.5K0.5)NbO3 (KNN) is considered a potential replacement for such ceramics. This work presents the synthesis of KNN-type ceramics based on conventional solid-state reaction, where the effect of precursor particle size is studied. A combined mechanical activation by ball milling and calcination at low temperature of 800 °C is applied. The phase structure evolution, morphology and mechanical properties are investigated systematically with the particle size and the calcination rate. The results indicate a marked effect of the precursor particle size on the properties of obtained ceramics. Secondary phase content could be lowered and tetragonality improved by the applied approach. Despite the presence of secondary phases, dielectric measurements indicated typical values of dielectric constant and loss for piezoelectric materials., [ES] La sustitución de las cerámicas piezoeléctricas comunes a base de plomo por una alternativa adecuada, se convirtió en un tema importante debido a las crecientes preocupaciones medioambientales por la toxicidad del plomo. Los (Na0.5K0.5)NbO3 (KNN) se consideran un posible reemplazo para cerámicas piezoeléctricas comunes a base de plomo. Este trabajo presenta la obtención de cerámicas tipo KNN mediante una reacción convencional en estado sólido donde se estudia el efecto del tamaño de las partículas precursoras. El método de síntesis ha empleado una combinación de molienda de atrición para activar la mezcla de precursores y de calcinación a baja temperatura de 800 °C. La evolución de las fases, la morfología y las propiedades mecánicas se investigan sistemáticamente con el tamaño de partícula y la rampa de calcinación. Los resultados indican un marcado efecto del tamaño de partícula del precursor sobre las propiedades de las cerámicas obtenidas. El contenido de fases secundarias y de la fase tetragonal se pueden ajustar ligeramente mediante el método presentado. Las medidas dieléctricas han indicado valores típicos para las cerámicas piezoeléctricas (constante dieléctrica y pérdidas) a pesar de la presencia de fases secundarias., This publication is part of the grant PID2021-128548OB-C21&C22 funded by MICIU/AEI/10.13039/501100011033 and by “ERDF/EU”, and the grant CNS2023-144190 funded by MICIU/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”. CIGRIS/2022/077 project funded by Generalitat Valenciana., Peer reviewed