Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D printing of cubic zirconia lattice supports for hydrogen production

  • Díaz-Herrezuelo, Irene
  • Koller, M.
  • Quintanilla, Asunción
  • Vega, G.
  • Casas, J. A.
  • Pérez-Coll, Domingo
  • Seiner, H.
  • Osendi, María Isabel
  • Miranzo López, Pilar
  • Belmonte, Manuel
The demand for hydrogen has extraordinarily grown during the last years, being one of the most attractive forms of fuels to produce green energy. Cubic zirconia ceramics are considered promising catalytic supports, and the additive manufacturing of porous 3D structures based on these ceramics could enhance their catalytic performance. Herein, lightweight highly porous (up to 88%) 3D patterned 8 mol% yttria-stabilized cubic zirconia (8YSZ) scaffolds are manufactured by robocasting from pseudoplastic aqueous-based inks to produce catalytic supports for the hydrogen (H2) production. These scaffolds are thermally treated at temperatures ranging between 1000 and 1400 ◦C and, hence, mechanically and electrically characterized. 3D 8YSZ structures sintered at 1200 ◦C, with an appropriate balance between high porosity (86%) and compressive strength (3.7 MPa), are impregnated with palladium (Pd) catalytic nanoparticles and employed in the catalytic dehydrogenation of renewable formic acid (FA) using a fixed-bed reactor. 3D Pd/8YSZ catalyst leads to the continuous production of CO-free H2 with a FA conversion of 32% at T = 55 ◦C., Proyectos RTI2018-095052-B-I00, PID2019-105079RB-I00, PID2021-125427OB-I00 EIN2020-112153, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modelling the anisotropic thermal conductivity of 3D logpile structures

  • Moreno-Sanabria, Luis
  • Barea, Rafael
  • Osendi, María Isabel
  • Belmonte, Manuel
  • Miranzo López, Pilar
[EN] Assessing and predicting the thermal conductivity (κ) of macroporous materials is particularly important for additive manufactured 3D structures, as they offer considerable potential for tuning architectures and properties. In this work, finite element methods (FEM) are used to simulate the transient plane source test in 3D logpile lattices, approaching the effect of interfacial thermal contact resistances on κ measurement. Besides, the influence of different geometrical parameters (rod diameter, macropore size and overlapping between rods in consecutive layers) and the κ of the strut material on the anisotropic thermal conductivity of 3D lattices are investigated. The models are validated using experimental data for 3D composite structures of γ-Al2O3 with graphene nanoplatelet contents up to 18 vol%, as well as with reported data for alike scaffolds, all printed by robocasting. Results have strong impact for the application of novel 3D structures in energy production and storage, catalysis and heat transfer-related fields., This work was supported by the Spanish Ministry of Science and Innovation through RTI2018-095052-B-I00 and PID2021-125427OB-I00 (MICINN/AEI/FEDER, UE) and EIN2020-112153 (MICINN/AEI/10.13039/501100011033) projects, the latter also supported by the European Union through “NextGenerationEU/PRTR”. L. M.-S. acknowledges the financial support from MICINN/AEI/FEDER through the FPI contract Ref. PRE2019-091429 (2019 call)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D-printed palladium/activated carbon-based catalysts for the dehydrogenation of formic acid as hydrogen carrier

  • Díaz-Herrezuelo, Irene
  • Vega, Gonzalo
  • Navarro, Marina
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Casas, José A.
  • Quintanilla, Asunción
  • Belmonte, Manuel
[EN] The development of structured catalyst supports to promote the chemical process intensification is of great interest, and porous activated carbon (AC) is an excellent material to tackle this challenge. In addition, the current increasing hydrogen demand and its limitations in transportation and storage require of novel approaches. Here, highly porous and robust 3D printed patterned AC-based architectures have been additive manufactured by using a direct ink writing technology. Different AC inks containing a boehmite gel with no organic additions have been rheologically characterized to select the most suitable ink for building AC supports, which have been thermally treated to promote solid-solid contacts and increase the robustness (strength of ~0.5 MPa) while keeping high porosity (86%). The AC supports have been then impregnated with a 5 wt.% of palladium (Pd) precursor to develop a 3D Pd/AC catalyst able to generate hydrogen from the dehydrogenation of formic acid (FA), a very promising liquid organic hydrogen carrier, in a fixed-bed reactor. These 3D catalysts have produced CO-free hydrogen from FA under ambient conditions with a FA conversion of 81% and a hydrogen flow rate of 6 mL·min-1. Long-term experiments in continuous mode operation have evidenced a good catalytic stability and recyclability. These results demonstrate that 3D Pd/AC catalysts exhibit a great potential to develop a new technology for using FA as hydrogen carrier., This work was supported by the Grants PID2021-125427OB-I00 and TED2021-130312B-I00 funded by MICIN/AEI/10.13039/501100011033 and by “ERDF A way of making Europe”, and by the Grant EIN2020-112153 funded by MCIN/AEI/10.13039/501100011033 and by “European Union NextGenerationEU/PRTR”. G. Vega acknowledges the Universidad Autónoma de Madrid for the Predoctoral contract. M. Navarro acknowledges the Community of Madrid for her contract under the “Programa Investigo”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D printing of cordierite materials from raw reactive mixtures

  • Dorado, B.
  • Moreno-Sanabria, Luis
  • García, E.
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Osendi, María Isabel
[EN] Porous cordierite materials are 3D printed by robocasting from two kaolin containing raw materials mixtures. Water suspensions of both mixtures at variable solid concentrations (40–67 wt%) are characterized by rheological measurements, showing good printability for concentrations >60 wt% without the need of any printing additive. The mixtures react during sintering (at 1250 °C) giving indialite as the main phase in the structures, which differ in minor phases. Three types of lattices are printed for both compositions with a logpile inner structure. Properties of interest like the coefficient of thermal expansion (CTE), the thermal conductivity (K) and the compression strength (σ) of the printed cordierites are determined and compared with published data. Results evidence that printing of clay containing reactive mixtures is a straightforward and cost-effective way to achieve porous complex shaped cordierite with CTE∼ 2–3 x10 K, K ∼ 0.4–0.6 W m K and maximum σ of 24 MPa., This work was supported by the Spanish Government through projects RTI2018-095052-B-I00 (MICINN/AEI/FEDER, UE) and EIN2020- 112153 (MCINN/AEI/10.13039/501100011033), the latter also supported by the European Union through “Next Generation EU/PRTR”. L. M.S. acknowledges the financial support from MICINN/AEI/FEDER through the FPI contract Ref. PRE2019-091429 (2019 call)., Supplementary data to this article can be found online at https://doi.org/10.1016/j.ceramint.2022.09.343, Peer reviewed