Pasar al contenido principal

FABRICACION ADITIVA DE ESTRUCTURAS CERAMICAS 3D MULTIFUNCIONALES PARA APLICACIONES TERMICAS

RTI2018-095052-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 30
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Rolled and twisted graphene flakes as self-lubricant and wear protecting fillers into ceramic composites

  • Llorente, Javier
  • Belmonte, Manuel
[EN] Dry reciprocating sliding tests have been performed on cubic yttria-stabilized zirconia ceramic composites containing graphene nanoplatelets. The composites exhibit an excellent friction response and, especially, an outstanding improvement of the wear resistance of more than two orders of magnitude, as compared to unfilled ceramics. The enhanced tribological response of these composites is much greater than that commonly reported for ceramic/graphene materials. The deep analysis of worn surfaces by combining confocal Raman, scanning electron and atomic force microscopies reveals the presence of abundant twisted graphene-based rolls on top of a thick carbonaceous tribofilm that played a decisive protagonist to extraordinarily improve the tribological performance of the composites through a roller-bearing like effect., This work was supported by Spanish project RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE). The authors acknowledge to Dr. A. del Campo, from ICV-CSIC, for his help in the Raman characterization., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improved crack resistance and thermal conductivity of cubic zirconia containing graphene nanoplatelets

  • Gómez-Gómez, Alberto
  • Ramírez, Cristina
  • Llorente, Javier
  • García, Ana
  • Moreno, Pablo
  • Reveron, Helen
  • Chevalier, Jérôme
  • Osendi, María Isabel
  • Belmonte, Manuel
  • Miranzo López, Pilar
[EN] Composites of 8 mol.% yttria-stabilized zirconia (8YSZ) with graphene nanoplatelets (GNP) have been pointed as alternative interconnectors in SOFC due to their mixed ionic-electronic conduction. Here we show that GNP addition provides rising crack-resistance behavior, with long crack toughness up to 78% higher than that of 8YSZ, also improving its thermal conductivity (up to 6 times for the in-plane direction). Toughness versus crack length is measured for 7 and 11 vol.% of GNP using single edge V-notched beam technique and ultrashort pulsed laser notching; and thermal behavior is analyzed by the laser flash method. Materials also have highly anisotropic coefficient of thermal expansion. These properties contribute to enhance their performance under the harsh operating conditions of SOFC, as thermal residual stresses could be reduced while significantly improving the system mechanical stability. Moreover, the heat transfer may be enhanced especially along the interface direction which would increase the system efficiency., This work was supported by Spanish project RTI2018-095052-B-I00, Ministerio de Ciencia, Innovacion y Universidades, Spain (MCIU/AEI/FEDER, UE). AG and PM acknowledge support from Ministerio de Economía, Industria y Competitividad, Spanish government (Project FIS2017- 87970-R) and Junta de Castilla y León, Spain (Project SA287P18). C. R. thanks the financial support by MCIU under contract IJCI-2017-34724 of “Juan de la Cierva” Program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Remarkable Effects of an Electrodeposited Copper Skin on the Strength and the Electrical and Thermal Conductivities of Reduced Graphene Oxide-Printed Scaffolds

  • Moyano, Juan J.
  • García Diego, Iñaki
  • Damborenea, Juan de
  • Pérez-Coll, Domingo
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Osendi, María Isabel
[EN] Architected Cu/reduced graphene oxide (rGO) heterostructures are achieved by electrodepositing copper on filament-printed rGO scaffolds. The Cu coating perfectly contours the printed rGO structure, but isolated Cu particles also permeate inside the filaments. Although the Cu deposition conveys a certain mass augment, the three-dimensional (3D) structures remain reasonably light (bulk density ≅ 0.42 g·cm–3). The electrical conductivity (σe) of the Cu/rGO structure (∼8 × 104 S·m–1) shows a notable increment compared to σe of the rGO structure (∼2 × 102 S·m–1). The effect on the scaffold robustness is also notable with an increase of the compressive strength by nearly 10 times (from 20 kPa of the rGO scaffold to 150 kPa of the Cu/rGO structure) and cyclability as well. The improved thermal conductivity of the Cu-coated scaffolds (∼4 times higher), in addition to the σe and strength improvements, suggests that 3D Cu/rGO structures could be suitable assemblies for integration into thermal dissipation systems, particularly as thermal interface materials, for compact electronic devices., This work was supported by Spanish project RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE). JJM acknowledges the financial support of MCIU through the FPI contract ref: BES-2016-077759., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Frequency-dependent acoustic energy focusing in hexagonal ceramic micro-scaffolds

  • Grabec, Tomáš
  • Koller, Martin
  • Sedlák, Petr
  • Kruisová, Alena
  • Román-Manso, Benito
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Seiner, Hanus
[EN] Acoustic properties of an additive-manufactured SiC scaffold with hexagonal symmetry fabricated by the robocasting method are studied both numerically and experimentally. The numerical analysis is based on the finite element method (FEM) using Bloch boundary conditions. The calculations show both angular and frequency dispersion of the acoustic waves with wavelengths comparable to the spacing between the rods, i.e., on a millimeter scale, indicating interesting acoustic properties in the MHz range. The dispersion character leads to focusing of the energy propagation into the directions of the rods of the hexagonal structure. This is illustrated by modal-based calculations of the propagation of longitudinal and out-of-plane shear wave packets with a dominant wavelength. The experimental analysis consists of two steps, the measurement of the resonant spectrum and shear wave propagation character. The measured resonant spectrum is in good agreement with the one calculated using numerically obtained low-frequency properties of the structure, also showing the quality of the overall manufactured structure. The time-domain measurement shows significant changes in the energy propagation between low and high frequencies, as predicted by FEM calculations., This work was supported by the Czech Science Foundation, Czechia grant no. GA17-01618S and by Spanish projects MAT2015-67437-R (MINECO, Spain, FEDER, Spain, UE) and RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The effect of rod orientation on the strength of highly porous filament printed 3D SiC ceramic architectures, Efecto de la orientación de los rodillos en la resistencia mecánica de estructuras 3D porosas de SiC fabricadas mediante impresión de filamento

  • Gómez-Gómez, Alberto
  • Moyano, Juan J.
  • Osendi, María Isabel
  • Belmonte, Manuel
  • Miranzo López, Pilar
[EN] The present work explores the strength enhancement via minor modifications of the pat-tern design in pure light SiC woodpile structures created by filament printing. In particular,the effect of the filament stacking angle on both the compression resistance and the elasticmodulus of these structures are evaluated. Different patterns were designed while main-taining the bulk structure density, therefore the differences in the mechanical data (strengthand elastic modulus) are not attributable to density variations. All of these materials werepartially sintered at intermediate temperature for additional porosity enhancement. More-over, SiC specimens made by full filament overlapping were produced to serve as referencemassive material. Remarkably, the massive SiC printed material displays ordered sphericalporosity and a closed-pore foam appearance, thus revealing a novel route for producingthese type of porosity. Results evidence that the structure robustness can be tuned throughslight design modification, which thus offers the possibility of further structure lighteningwithout reducing the target strength., [ES] El presente trabajo explora la mejora de la resistencia mecánica de estructuras ligeras for-madas por apilamiento de rodillos de SiC puro, procesadas por impresión directa de tinta, através de modificaciones menores del patrón de dise ̃no. En particular, se evalúa el efecto del ángulo de apilamiento de los filamentos sobre la resistencia a la compresión y el móduloelástico de estas estructuras. Los diferentes patrones fueron dise ̃nados manteniendo sim-ilares densidades aparentes de las estructuras, por lo tanto, las diferencias observadas enlos resultados mecánicos (resistencia y módulo elástico) no son atribuibles a variaciones dedensidad. Todas las estructuras se sinterizaron parcialmente para mantener una elevadaporosidad. Además, se produjeron muestras de SiC macizas creadas por la superposiciónde filamentos utilizadas como material masivo de referencia. Curiosamente, este materialmuestra una porosidad esférica y ordenada, y presenta la apariencia típica de esponjas conporosidad cerrada, mostrando en consecuencia una ruta alternativa para la fabricación deeste tipo de materiales celulares. Dado que la robustez de estructuras 3D se puede maximizara través de una ligera modificación del dise ̃no, esto permitiría alternativamente aligerar aúnmás las estructuras sin perjudicar su resistencia., This work was supported by projects MAT2015-67437-R and RTI2018-095052-B-I00 financed by the Ministerio de Ciencia, Innovación y Universidades MCIU (previously MINECO),Spain/FEDER (UE). J.J. Moyano acknowledges the financialsupport of MCIU/FEDER through the FPI contract ref: BES-2016-077759, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High graphene fillers content for improving the tribological performance of silicon nitride-based ceramics

  • Llorente, Javier
  • Ramírez, Cristina
  • Belmonte, Manuel
The effect of large graphene nanoplatelets (GNPs) additions on the friction and wear of silicon nitride (Si3N4) ceramics is evaluated under isooctane lubrication. All Si3N4/GNPs composites, with up to 20.6 vol% of graphene fillers, exhibit better tribological response than Si3N4, in particular, a 50% reduction in the friction that continuously decreases with the GNPs content is attained, jointly with an improvement in the wear resistance of up to 63%. The survival of a self-lubricant carbon-rich tribolayer formed on the worn surfaces controls the tribological properties of the materials. Si3N4/GNPs composites are promising materials to enhance the performance of gasoline direct injection systems., This work was supported by projects MAT2015-67437-R(MICINN,FEDER,UE) and RTI2018-095052-B-I00 (MICINN), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Caracterización tribológica de materiales compuestos cerámica/grafeno

  • Llorente, Javier
[EN] In this work, the tribological characterization of ceramic materiales containing high graphene nanostructures contents (up to 20 vol. %) is carried out. In particular, the effect of the addition of graphene nanoplatelets and graphene oxide in different ceramic matrices, such as silicon nitride, silicon carbide and cubic zirconia, is discussed, under dry and isooctane lubricated sliding conditions. It is described how, in general, high graphene nanostructres contents are needed to achieve significant improvements in friction and wear behaviour, which could permit to use of these materiales in, for example, gasolina direct injection systems. Moreover, the influence of the microstructural charateristics of both, the ceramic matrices and the graphene nanostructures is described, showing how these issue play a critical role in the tribological behaviour of these systems, being the most preferable situation, to use thin graphene nanostructures, due to its better integration in the ceramic matrix., [ES] ): En este trabajo se realiza la caracterización tribológica de materiales cerámicos con elevados contenidos de diferentes nanoestructuras de grafeno, de hasta el 20%. Vol. En particular, se estudia el efecto de la adición de nanoplaquetas de grafeno y óxido de grafeno en distintas matrices cerámicas: nitruro de silicio, carburo de silicio y circona cúbica, tanto bajo deslizamiento en seco como en lubricación con isooctano. Se describe como, en general, son necesarios contenidos elevados de nanoestructuras de grafeno para alcanzar mejoras en fricción y desgaste, que permitan el uso de estos materiales, por ejemplo, en sistemas de inyección directa de gasolina. Además se realiza un estudio de como las características microestructurales tanto de las nanoestructuras de grafeno utilizadas, como de las distintas matrices cerámicas, juegan un papel fundamental en las propiedades tribológicas de estos sistemas, siendo preferible el empleo de nanoestructuras finas, gracias a su mejor integración en la matriz cerámica., El trabajo experimental correspondiente a esta tesis doctoral se ha financiado a través de los proyectos MAT2012-32944 (MINECO), MAT2015-67437-R (MICINN. FEDER, UE) y RTI2018-095052-B-I00 (MCIU/AEI/FDER, UE)., Tribological performance under dry sliding conditions of graphene/silicon carbide composites. Journal of the European Ceramic Society. (2016). doi: 10.1016/j.jeurceramsoc.2015.09.040, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Robust and conductive mesoporous reduced graphene oxide-silica hybrids achieved by printing and the sol gel route

  • Moyano, Juan J.
  • Loizillon, J.
  • Pérez-Coll, Domingo
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Grosso, David
  • Osendi, María Isabel
[EN] Reduced graphene oxide (rGO) scaffoldings are used as templates to create lightweight 3D rGO/silica and rGO/silico-aluminate hybrids by a simple impregnation route and the sol-gel method. The printed rGO assemblies are infiltrated by the corresponding alkoxide precursor solution and gelled by exposure to ammonia vapours, producing an hybrid replica of the rGO structure. The hybrids show a significant prevalence of mesopores, with total porosity above 94 %, density of ~ 0.1 g¿cm¿3 and high specific surface area (¿ 190 m2¿g¿1). As a result, the 3D composite materials show enhanced water adsorption capacity and hydrophilicity, display compressive strengths in the range 0.1 ¿ 0.4 MPa, which scale with the proportion of silica (or Al-modified silica) on the hybrid scaffold, and electrical conductivities are above 60 S¿m¿1. These properties are very attractive for applications in the removal of pollutants, water filtering, catalysis, drug delivery, or energy production and storage., This work was supported by Spanish project RTI2018-095052-B-I00 (MICINN/AEI, Spain and FEDER, UE). JJM acknowledges the financial support of MICINN through the FPI contract ref: BES-2016-077759
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Graphene-based nanostructures as catalysts for wet peroxide oxidation treatments: From nanopowders to 3D printed porous monoliths

  • Quintanilla, Asunción
  • Carbajo, J.
  • Casas, José A.
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Belmonte, Manuel
[EN] This paper explores the catalytic behaviour of different graphene-based nanostructures for the treatment of wastewater using Catalytic Wet Peroxide Oxidation (CWPO) processes. In a first stage, graphene-based nanopowders with distinct physical-chemical characteristics are tested in the CWPO of phenol using the following standard operating conditions: [Phenol] = 1 g·L, [HO] = 5 g L and 80 °C. Graphene nanoplatelets with the lowest oxygen content exhibit the highest catalytic activity. The typical phenol oxidation by-products are detected in the liquid phase while CO and CO appear in the gas phase. Afterwards, three dimensional (3D) porous graphene monoliths (D ∼ 11.5 mm, H ∼ 4 mm, D ∼ 0.68 mm and δ =0.36 cm, 75 cells·cm, ε = 41%) based on those nanoplatelets are additive manufactured using a direct ink writing technique and, then, tested under similar CWPO conditions. The results evidence that the 3D graphene-based structures are catalytically active, though they undergo a progressive deactivation due to the deposition of organic matter. The graphene-based monoliths can be regenerated by thermal treatments, allowing their use at industrial scale by means of reaction-thermal regeneration cycles., The authors thank the financial support by the Spanish Ministerio de Ciencia, Innovación y Universidades (MICINN) and FEDER program (EU) through the projects: CTM2016-76454-R (MICINN), MAT2015-67437-R (MICINN/ FEDER,UE) and RTI2018-095052-B-I00 (MICINN).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Understanding the active sites of boron nitride for CWPO: An experimental and computational approach

  • Quintanilla, Asunción
  • Vega, Gonzalo
  • Carbajo, J.
  • Casas, José A.
  • Lei, Y.
  • Fujisawa, K.
  • Liu, H.
  • Cruz-Silva, R.
  • Terrones, M.
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Belmonte, Manuel
  • Fernández Sanz, Javier
[EN] Hexagonal boron nitride (h-BN) has been explored as a catalyst for degrading persistent organic pollutants in wastewater by Catalytic Wet Peroxide Oxidation (CWPO). Herein, the superior activity of the h-BN on the phenol degradation (model pollutant) compared to other metal-free catalysts, such as carbon-based ones, and the lower selectivity to CO encourage the potential application of h-BN catalysts in CWPO processes. Through a combined density functional theory calculations, experimental reactions and catalyst characterization approach, a comprehensive study on the reaction mechanism has been conducted. According to this, only defected B atoms in the h-BN layer, protonated as B-(OH), decompose the hydrogen peroxide into highly reactive hydroxyl radicals. The radical species diffuse towards inner h-BN regions and react with the phenol adsorbed by π-π interaction on the h-BN surface. Oxidation by-products cause carbonaceous deposits and progressive deactivation of the h-BN catalyst that can be directly regenerated by burning off in air., The authors thank the financial support by the Community of Madrid and the Government of Spain through the projects: S2018/EMT- 4341 and RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE), respectively. The work done at the University of Sevilla was funded by Spanish Ministerio de Ciencia e Innovación and EU-FEDER, grant PID2019-106871 GB-I00, and the Junta de Andalucía-FEDER, grant: US-1381410. Also, G. Vega acknowledges the Community of Madrid for the Predoctoral contract PEJD-2018-PRE/AMB-9019, co-financed by the European Social Fund through the Youth Employment Operational Program and the Youth Employment Initiative (YEI) 2018. J. Carbajo thanks the financial support by the Government of Spain for a grant under the Juan de la Cierva_Incorporación programme (IJCI-2017- 32682). The authors would like to thank A. Pérez for performing the BET and TGA measurements.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Iron-based metal-organic frameworks integrated into 3D printed ceramic architectures

  • Salazar-Aguilar, Alma D.
  • Quintanilla, Asunción
  • Vega-Díaz, Sofía Magdalena
  • Casas, José A.
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Belmonte, Manuel
[EN] The promising applications of metal-organic frameworks (MOF) can be widened if these materials were additive manufactured to develop three-dimensional (3D) MOF architectures. In this work, iron-based MOF/silicon carbide (SiC) composite aqueous inks with a high solids content (64 ​wt%) are printed into 3D periodic lattices by a direct ink writing technique (Robocasting). MOF appear fully integrated within the cellular architectures, which display total porosities in the range of 74–78% depending on the scaffold design. The 3D MOF-Fe/SiC structures exhibit good mechanical strength (~4.6 ​MPa) and a semiconductor-like behaviour. The structures show a remarkable response in the hydroxylation of phenol with hydrogen peroxide, demonstrating high selectivity and yield to dihydroxybenzene species., This work was supported by the following funding organisms and projects: Spanish Government under the project RTI2018-095052-BI00 (MICINN/AEI/FEDER, UE), Community of Madrid under the project S2018/EMT-4341, CSIC project I-COOPþ 2019 (Ref. COOPB20405), TNM projects 7936.20-P and 9063.20-P, and CONACYT under the project 764635. Authors thank Dr. D. Pérez-Coll for his experimental assistance in the electrical measurements.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Heat dissipation in 3D printed cellular aluminum nitride structures

  • Belmonte, Manuel
  • López Navarrete, Gonzalo
  • Osendi, María Isabel
  • Miranzo López, Pilar
[EN] The improvement of heat dissipation in electronic and energy devices is a challenge that can be addressed through the use of highly porous materials. Presently, the additive manufacturing of 3D aluminum nitride is described, and different lattice patterns with porosities in the range 45–64 % are achieved by direct ink writing. All the structures are robust and the effective thermal conductivity (k) for cuboid structures decreases by 50–75 % with the filament separation and shows anisotropic characteristics, since k along the longitudinal axis of the scaffold is up to six times greater than for the transversal one. Heat transfer during free cooling experiments for cuboid and cylinder scaffolds, after rapid heating at temperatures above 1000 °C, takes place by radiation for temperatures >500 °C and by convection through the complete cooling process. The heat dissipation time constants of both processes decrease almost linearly with the designed scaffold parameters of porosity and rod separation., This work was supported by the Spanish project RTI2018-095052-BI00 (MICINN/AEI/FEDER, UE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D honeycomb monoliths with interconnected channels for the sustainable production of dihydroxybenzenes: towards the intensification of selective oxidation processes

  • Vega, Gonzalo
  • Quintanilla, Asunción
  • Menéndez, Nieves
  • Belmonte, Manuel
  • Casas, José A.
[EN] Novel 3D Fe/SiC honeycomb monolithic reactors with different morphologies (i.e. cell geometry, cell density and interconnected channel pattern) have been conceptually designed, digitally prototyped and manufactured by robocasting. Square, tronco-conical and triangular cell geometries with parallel channels presenting staggered or faced interconnections have been tested in the phenol hydroxylation reaction with hydrogen peroxide to produce dihydroxybenzenes, such as catechol and hydroquinone. The analysis of the valence state of iron in the monoliths by Mössbauer spectroscopy identified iron silicides, viz. FeSi and α-FeSi, as the iron catalytic species. The results demonstrate that an increased macro-channel tortuosity, favoured by a high density cell and a high number of not-facing inter-connected channels, facilitates the selectivity to the dihydroxybenzenes. In particular, 3D Fe/SiC monoliths with triangular cells provide an outstanding improvement with respect to the commercial process, not only because of their superior performance (S=99.1% and Y=29.6% at 80 ºC) and stability (over 8 days on stream) but also in sustainability (i.e. operation in flow-reactor, no need of catalyst filtration, water as unique solvent). The additive manufacturing has allowed the smart integration of the catalytic phase into the monolithic structure, enabling, by this way, to architecture the reactor independently on its chemical composition., The authors thank the financial support by the Community of Madrid through the project S2018/EMT-4341 and the Government of Spain through the projects: PGC2018-095642-B-I00 and RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE). Also, G. Vega acknowledges the Community of Madrid for the Predoctoral contract PEJD-2018-PRE/AMB-9019, co-financed by the European Social Fund through the Youth Employment Operational Program and the Youth Employment Initiative (YEI) 2018. The authors would like to thank Alvaro Pérez for performing the BET and TGA measurements.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Fluid Dynamics in 3D Monolithic Reactors to Improve the Chemical Performance: Experimental and Numerical Investigation

  • Quintanilla, Asunción
  • Vega, Gonzalo
  • López, Pablo
  • García, Francesca
  • Madurga, Enrique
  • Belmonte, Manuel
  • Casas, José A.
[EN] Three-dimensional (3D) Fe/SiC monoliths with parallel interconnected channels and different cell geometries (square, troncoconical, and triangular) were manufactured by robocasting and used as catalytic reactors in hydroxylation of phenol using hydrogen peroxide to produce dihydroxybenzenes; the reaction was performed at Cphenol,0 = 0.33 M, Cphenol,0:CH2O2,0 = 1:1 M, WR = 3.7 g, T = 80-90 °C, and τ = 0-254 gcat·h·L-1 with water as a solvent. The values of the apparent kinetic rate constants demonstrated the superior performance of the triangular cell monoliths for hydrogen peroxide decomposition, phenol hydroxylation, and dihydroxybenzene production reactions. A computational fluid dynamic model was validated with the experimental results. It demonstrated that the triangular cell monoliths, with a lower channel hydraulic diameter and not-facing interconnections, provided a higher internal macrotortuosity that induced an oscillating flow of the liquid phase inside the channels, leading to an additional transverse flow between adjacent parallel channels. This behavior, not observed in the other two geometries, resulted in a better overall performance., The authors thank the financial support by the Community of Madrid through the project S2018/EMT-4341 and the Government of Spain through the projects: PGC2018-095642-B-I00 and RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE). Also, G. Vega acknowledges the Universidad Autónoma de Madrid for the predoctoral contract.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multifunctional performance of Ti2AlC MAX phase/2D braided alumina fiber laminates

  • González Julián, Jesús
  • Kraleva, Irina
  • Belmonte, Manuel
  • Jung, Fabian
  • Gries, Thomas
  • Bermejo, Raúl
[EN] The processing and characterization of laminates based on TiAlC MAX phase, as matrix, and triaxial alumina braids, as reinforcing phase, are presented. TiAlC powders with a mean particle size below 1 µm are synthesized, while commercial 3M Nextel 610 alumina fibers are braided in a three-stage process consisting of spooling, braiding with an angle of 0° and ±60° and the separation to single-layer fabric. The laminates are processed by layer-by-layer stacking, where 3 two-dimensional alumina braids are interleaved between TiAlC layers, followed by full densification using a Field-Assisted Sintering Technology/Spark Plasma Sintering. The multifunctional response of the laminates, as well as for the monolithic TiAlC, is evaluated, in particular, the thermal and electrical conductivity, the oxidation resistance, and the mechanical response. The laminates exhibit an anisotropic thermal and electrical behavior, and an excellent oxidation resistance at 1200℃ in air for a week. A relatively lower characteristic biaxial strength and Weibull modulus (i.e., σ = 590 MPa and m = 9) for the laminate compared to the high values measured in the monolithic TiAlC (i.e., σ = 790 MPa and m = 29) indicates the need but also the potential of optimizing MAX-phase layered structures for multifunctional performance., Germany’s Federal Ministry of Education and Research (“Bundesministerium für Bildung und Forschung”), Grant/Award Number: 03SF0534; Spanish Ministry of Science and Innovation (MICINN/AEI) and FEDER (UE), Grant/Award Number: RTI2018- 095052- BI00; European Research Council (ERC), Grant/Award Number: 817615
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal conduction in three-dimensional printed porous samples by high resolution infrared thermography

  • Muñoz Codorníu, Diego
  • Moyano, Juan J.
  • Belmonte, Manuel
  • Osendi, María Isabel
  • Miranzo López, Pilar
[EN] The thermal conductivity (κ) is a key parameter that defines many of the technological uses of three-dimensional (3D) porous architectures. Despite the variety of methods for determining κ, problems generally arise when re-searchers try to apply them to cellular materials and 3D structures. The present work proposes an affordable lab-madedevice for analysing anisotropic heat flow in 3D porous architectures via high resolution infrared ther-mography. The method is validated using dense materials of known thermal conductivity. Temperature gradients measured for porous specimens have been correlated to the thermal conductivity estimated from a simple resistors model, assessing the main factors that affect the experimental measurements. The porous specimens of SiC, MAX- phase and graphene-based nanostructures are in-house manufactured by direct ink writing (robocasting)., This work was supported by Spanish project RTI2018-095052-B-I00 (MICINN/AEI/FEDER, UE). JJM acknowledges the financial support of MICINN through the FPI contract ref: BES-2016-077759. DMC thanks the UPM financial aid for graduate students.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Applications of ceramic/graphene composites and hybrids

  • Ramírez, Cristina
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Osendi, María Isabel
[EN] Research activity on ceramic/graphene composites and hybrids has increased dramatically in the last decade. In this review, we provide an overview of recent contributions involving ceramics, graphene, and graphene-related materials (GRM, i.e., graphene oxide, reduced graphene oxide, and graphene nanoplatelets) with a primary focus on applications. We have adopted a broad scope of the term ceramics, therefore including some applications of GRM with certain metal oxides and cement-based matrices in the review. Applications of ceramic/graphene hybrids and composites cover many different areas, in particular, energy production and storage (batteries, supercapacitors, solar and fuel cells), energy harvesting, sensors and biosensors, electromagnetic interference shielding, biomaterials, thermal management (heat dissipation and heat conduction functions), engineering components, catalysts, etc. A section on ceramic/GRM composites processed by additive manufacturing methods is included due to their industrial potential and waste reduction capability. All these applications of ceramic/graphene composites and hybrids are listed and mentioned in the present review, ending with the authors’ outlook of those that seem most promising, based on the research efforts carried out in this field., This research was funded by the Spanish Ministry of Science and Innovations (MICINN/AEI) and FEDER (UE), grant number RTI2018-095052-BI00. CR acknowledges the funding from Juan de la Cierva Incorporación Postdoctoral Program (IJCI-2017-34724).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Kinetic study of phenol hydroxylation by H2O2 in 3D Fe/SiC honeycomb monolithic reactors: Enabling the sustainable production of dihydroxybenzenes

  • Vega, Gonzalo
  • Quintanilla, Asunción
  • Belmonte, Manuel
  • Casas, José A.
[EN] The chemical kinetics of phenol hydroxylation by hydrogen peroxide (HO) to produce dihydroxybenzenes was studied using a 3D printed monolithic reactor. The monoliths were manufactured by the Robocasting technique. They consisted on honeycomb-structured Fe/SiC nanoparticles (13.5 mm in diameter and 14.8 mm in length) with triangle cell geometry and staggered interconnected channels (71 cells per cm). The isothermal reactor was constituted by three stacked monoliths and was operated as an ideal plug flow reactor, according to the measured residence time distribution. The hydroxylation experiments were carried out at C = 0.33 M, phenol:HO molar ratio 1:1, τ(space time) = 0–254 g h L, T = 80, 85 and 90 °C and water as unique solvent. Experimental results showed no mass transfer limitations. The best fits were obtained for HO decomposition with a Langmuir-Hinshelwood-Hougen-Watson kinetic model and for phenol hydroxylation, as well as, catechol and hydroquinone production, with an Eley-Rideal kinetic model. The hydroxylation reaction mechanism underling to the developed model involved three elementary reactions: (1) adsorption of HO molecules on the iron active sites, (2) chemical surface HO decomposition into the hydroxyl radical species, and (3) reaction between adsorbed radical species and phenol in solution leading to the dihydroxybenzene formation and freeing the iron catalytic active sites (rds). This work contributes to the implementation of outstanding 3D Fe/SiC honeycomb monolithic reactors, with a dihydroxybenzene selectivity above 99% at 80 °C, for the sustainable production of hydroxylated aromatics., The authors thank the financial support by the Community of Madrid through the project S2018/EMT-4341 and the Government of Spain through the projects: PID2019-105079RB-I00, PGC2018-095642-B-I00 and RTI2018-095052-B-I00 (MCIU/AEI/FEDER, UE). Also, G. Vega acknowledges the Universidad Autonoma de Madrid for the Predoctoral contract FPI/UAM2021.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D-Printed Fe/γ-Al2O3 Monoliths from MOF-Based Boehmite Inks for the Catalytic Hydroxylation of Phenol

  • Salazar-Aguilar, Alma D.
  • Quintanilla, Asunción
  • López, Pablo
  • Martínez, Carla
  • Vega-Díaz, Sofía Magdalena
  • Casas, José A.
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Belmonte, Manuel
[EN] The synthesis of dihydroxybenzenes (DHBZ), essential chemical reagents in numerous industrial processes, with a high degree of selectivity and yield from the hydroxylation of phenol is progressively attracting great interest in the catalysis field. Furthermore, the additive manufacturing of catalysts to produce 3D printed monoliths would provide additional benefits to enhance the DHBZ synthesis performance. Herein, 3D cellular Fe/γ-Al2O3 monoliths with a total porosity of 88% and low density (0.43 g·cm-3) are printed by Robocasting from pseudoplastic Fe-metal-organic frameworks (Fe-MOF)-based aqueous boehmite inks to develop catalytic monoliths containing a Fe network of dispersed clusters (≤5 μm), nanoclusters (<50 nm), and nanoparticles (∼20 nm) into the porous ceramic skeleton. The hydroxylation of phenol in the presence of hydrogen peroxide is carried out at different reaction temperatures (65-85 °C) in a flow reactor filled with eight stacked 3D Fe/γ-Al2O3 monoliths and with the following operating conditions: Cphenol,0 = 0.33 M, Cphenol,0/CH2O2,0 = 1:1 molar, WR = 2.2 g, and space time (τ = W·QL-1) = 0-147 gcat·h·L-1. The scaffolds present a good mechanical resistance (∼1 MPa) to be employed in a catalytic reactor and do not show any cracks or damage after the chemical reaction. DHBZ selectivity (SDHBZ) of 100% with a yield (YDHBZ) of 32% due to the presence of the Fe network in the monoliths is reported at 85 °C, which represents an improved synthesis performance as compared to that obtained by using the conventional Enichem process and the well-known titanium silicalite-1 catalysts (SDHBZ = 99.1% and YDHBZ = 29.6% at 80 °C). This printing strategy allows manufacturing novel 3D structured catalysts for the synthesis of critical chemical compounds with higher reaction efficiencies., This work was supported by the following agencies and grants: Spanish Government under the project RTI2018-095052-BI00 (MICINN/AEI/FEDER, UE), Community of Madrid under project S2018/EMT-4341, and CSIC project I–COOP+ 2019 (ref. COOPB20405). P.L. acknowledges the Community of Madrid and the European Social Fund for the financing received through the contract PEJ-2019-AI/IND-14385.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Monolithic Stirrer Reactors for the Sustainable Production of Dihydroxybenzenes over 3D Printed Fe/γ-Al2O3 Monoliths: Kinetic Modeling and CFD Simulation

  • López, Pablo
  • Quintanilla, Asunción
  • Salazar-Aguilar, Alma D.
  • Vega-Díaz, Sofía Magdalena
  • Díaz-Herrezuelo, Irene
  • Belmonte, Manuel
  • Casas, José A.
[EN] The aim of this work is to evaluate the performance of the stirring 3D Fe/AlO monolithic reactor in batch operation applied to the liquid-phase hydroxylation of phenol by hydrogen peroxide (HO ). An experimental and numerical investigation was carried out at the following operating conditions: C = 0.33 M, CO,0 = 0.33 M, T = 75–95C, P = 1 atm, ω = 200–500 rpm and W ~ 1.1 g. The kinetic model described the consumption of the HO by a zero-order power-law equation, while the phenol hydroxylation and catechol and hydroquinone production by Eley–Rideal model; the rate determining step was the reaction between the adsorbed HO, phenol in solution with two active sites involved. The 3D CFD model, coupling the conservation of mass, momentum and species together with the reaction kinetic equations, was experimentally validated. It demonstrated a laminar flow characterized by the presence of an annular zone located inside and surrounding the monoliths (u = 40–80 mm s ) and a central vortex with very low velocities (u = 3.5–8 mm s ). The simulation study showed the increasing phenol selectivity to dihydroxybenzenes by the reaction temperature, while the initial HO concentration mainly affects the phenol conversion., This work was funded by the following agencies and grants: Spanish Government under project RTI2018-095052-BI00 (MICINN/AEI/FEDER, UE), Community of Madrid under project S2018/EMT-4341, and CSIC project I-COOP+ 2019 (Ref. COOPB20405). P. Lopez acknowledges the Community of Madrid and the European Social Fund for the financing received through the contract PEJ-2019-AI/IND-14385
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structured Reactors Based on 3D Fe/SiC Catalysts: Understanding the Effects of Mixing

  • Vega, Gonzalo
  • Quintanilla, Asunción
  • López, Pilar
  • Belmonte, Manuel
  • Casas, José A.
[EN] The application of structured reactors provides a number of advantages in chemical processes. In this paper, two different three-dimensional (3D) Fe/SiC catalysts with a square cell geometry have been manufactured by Robocasting: monoliths (D = 14 and H = 15 mm) and meshes (D = 24 and H = 2 mm) and studied in the catalytic phenol oxidation by hydrogen peroxide (HO) for the sustainable production of dihydroxybenzenes (DHBZ). The fluid dynamics, catalytic performance, reaction rates, external mass transport limitation, and catalyst stability have been compared in three different reactors, monolithic fixed-bed reactor, multimesh fixed-bed reactor, and monolithic stirrer reactor, at selected operating conditions. The results show that the mechanical stirring of the 3D Fe/SiC monoliths avoids the external mass transfer limitation caused by the presence of oxygen bubbles in the channels (produced from the HO· species in autoscavenging radical reactions). In addition, the backmixing has a positive effect on the efficient consumption of HObut an adverse effect on the phenol selectivity to DHBZ since they are overoxidized to tar products at longer contact times. On the other hand, the wall porosity, and not the backmixing, affects the susceptibility of the 3D Fe/SiC catalyst to the Fe leaching, as occurs in the mesh structures. In conclusion, the monoliths operating under plug-flow and external mass transfer limitation in the monolithic fixed-bed reactor (MFB) provide an outstanding phenol selectivity to DHBZ and catalyst stability., This work is supported by the following agencies and grants: the Spanish Government under projects RTI2018-095052-BI00 (MICINN/AEI/FEDER, UE) and EIN2020-112153 (MCINN/AEI/10.13039/501100011033), the latter was also supported by the European Union through “NextGenerationEU/PRTR”, Community of Madrid under project S2018/EMT-4341, and CSIC project I-COOP+ 2019 (ref COOPB20405). P.L. acknowledges the Community of Madrid and the European Social Fund for the financial support received through the contract PEJ-2019-AI/IND-14385. The authors thank Juliana Mejía for her technical assistance.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced Thermal and Mechanical Properties of 3D Printed Highly Porous Structures Based on γ-Al2O3 by Adding Graphene Nanoplatelets

  • Moreno-Sanabria, Luis
  • Ramírez, Cristina
  • Osendi, María Isabel
  • Belmonte, Manuel
  • Miranzo López, Pilar
[EN] One of the main challenges to widen the potential applications of 3D printed highly porous ceramic structures in catalysis, energy storage or thermal management resides in the improvement of both their mechanical resistance and thermal conductivity. To achieve these goals, highly hierarchical γ-alumina (γ-AlO) scaffolds containing up to 18 vol% of graphene nanoplatelets (GNP), including channels of controlled size and shape in the millimeter scale and meso-porosity within the rods, are developed by robocasting from boehmite-based aqueous inks without other printing additives. These 3D structures exhibit high porosity (85%) and specific surface area of 100 m g. The incorporation of 12 vol% GNP leads to an enhanced mechanical response of the scaffolds, increasing the compressive strength and the elastic modulus up to ≈80% as compared with data for plain γ-AlO scaffolds. The thermal conductivity is measured by the transient plane source method using specifically designed 3D structures with external sidewalls and additional top/bottom covers to assure a good contact at the outer surfaces. The thermal conductivity of 3D porous structures augments with the GNP content, reaching a maximum value four times higher for the scaffolds containing 18 vol% GNP than that attained for the 3D monolithic γ-AlO., This work was supported by the Spanish Government through RTI2018-095052-B-I00 (MICINN/AEI/FEDER, UE) and EIN2020-112153 (MCIN/AEI/10.13039/501100011033) projects, the latter also supported by the European Union through “NextGenerationEU/PRTR”. L.M.-S. acknowledges the financial support from MICINN/AEI/FEDER through the FPI contract Ref. PRE2019-091429 (2019 call)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel 3D thermal energy storage materials based on highly porous patterned printed clay supports infiltrated with molten nitrate salts

  • Díaz-Herrezuelo, Irene
  • Moreno-Sanabria, Luis
  • Miranzo López, Pilar
  • Osendi, María Isabel
  • Belmonte, Manuel
[EN] One of the main drawbacks of phase change materials (PCM) to be employed as thermal energy storage (TES) systems in energy applications, such as concentrated solar power (CSP), is the liquid leakage, which considerably reduces the storage efficiency. To overcome this issue, a novel approach is presented, which is based on the development of three-dimensional (3D) engineered TES structures (3DTES) formed by highly porous patterned 3D printed low-cost clay supports (up to ~85% of total porosity) that are infiltrated with a molten sodium nitrate salt. Expanded vermiculite supports are additive manufactured by robocasting, a direct ink writing technology, using clay aqueous inks with a pseudoplastic behavior. 3DTES are lightweight (~1.8 g·cm), easy to handle, mechanically robust (~68 MPa) and exhibit high PCM encapsulation capacity (~78%), avoiding the molten salt leakage. Furthermore, they present an enthalpy of fusion of ~136 J·g, excellent thermal stability, and high thermal energy storage efficiency (~80%) and thermal conductivity (1.27 W·m·K), which is indicative of a great charging-discharging ability. The results open new opportunities through the 3DTES approach to manufacture promising affordable materials with outstanding performance for CSP applications., This work was supported by the Spanish Government through RTI2018–095052-B-I00 (MICINN/AEI/FEDER, UE) and EIN2020–112153 (MCINN/AEI/10.13039/501100011033) projects, the latter also supported by the European Union through “NextGenerationEU/PRTR”. I. D.-H. acknowledges the Community of Madrid and European Social Fund for the Predoctoral contract PEJD-2019-PRE/IND-16861. L. M.-S. acknowledges the financial support from MICINN/AEI/ FEDER through the FPI contract Ref. PRE2019–091429 (2019 call)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reinforced 3D composite structures of γ-Al2 O3 with carbon nanotubes and reduced go ribbons printed from boehmite gels

  • Ramírez, Cristina
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Osendi, María Isabel
[EN] The ability of boehmite to form printable inks has sparked interest in the manufacturing of 3D alumina (Al O) and composite structures by enabling direct ink writing methods while avoiding the use of printing additives. These materials may exhibit high porosity due to the printing and sintering procedures, depending on the intended application. The 3D-printed porous composite structures of γ-Al O and α-Al O containing 2 wt.% of carbon nanotubes or reduced graphene oxide ribbons were fabricated from boehmite gels, followed by different heat treatments. The reinforcing effect of these carbon nanostructures was evidenced by compression tests carried out on the different alumina structures. A maximum relative increase of 50% in compressive strength was achieved for the γ-Al O composite structure reinforced with reduced graphene oxide ribbons, which was also accompanied by an increase in the specific surface area., Spanish Ministry of Science and Innovation (MICINN/AEI) and FEDER (UE), grant number RTI2018-095052-B-I00.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CVD nanocrystalline multilayer graphene coated 3D-printed alumina lattices

  • Ramírez, Cristina
  • Shamshirgar, Ali Saffar
  • Pérez-Coll, Domingo
  • Osendi, María Isabel
  • Miranzo López, Pilar
  • Tewari, Girish C.
  • Karppinen, Maarit
  • Hussainova, Irina
  • Belmonte, Manuel
[EN] 3D printing technologies have expanded the possibilities of fabricating new composite materials with tailored properties, which depend on both the materials selected and the structural design at multiple length scales. Here, a catalyst-free CVD method has been used to produce hybrid materials based on 3D printed cellular α-Al2O3 substrates decorated by either nanocrystalline graphene or nanocrystalline graphitic films of tunable number of layers. Graphene-based coatings of variable thickness and crystallinity have been controlled by the alteration of the parameters of CVD processing, performed under CH4/H2 flux. Transmission electron microscopy has confirmed the effective growth of nanocrystalline graphene layers on the scaffolds due to the penetration of CVD gases into the open pores. The fully-connected and highly conductive 3D pathways have displayed a room temperature electrical conductivity in the range of 101–103 S m−1. Furthermore, the thermal conductivity has also increased by 50% for the specimen decorated with a 20 nm thick graphitic coating as compared to a bare 3D ceramic scaffold. The developed structures open up new possibilities for expanding the field of application of graphene/ceramic composites for conditions requiring dielectric substrates of various shapes coated with conductive films or graphene-based catalytic supports with good structural stability., This work was supported by the Spanish Government through RTI2018-095052-B-I00, PID2020-120562RJ-I00 (MICINN/AEI/FEDER,UE) and EIN2020-112153 (MCINN/AEI/10.13039/501100011033, supported by the European Union through “NextGenerationEU/PRTR”) projects, as well as the Estonian Research Council under the personal grant PRG643 (I. Hussainova)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D printing of cubic zirconia lattice supports for hydrogen production

  • Díaz-Herrezuelo, Irene
  • Koller, M.
  • Quintanilla, Asunción
  • Vega, G.
  • Casas, J. A.
  • Pérez-Coll, Domingo
  • Seiner, H.
  • Osendi, María Isabel
  • Miranzo López, Pilar
  • Belmonte, Manuel
The demand for hydrogen has extraordinarily grown during the last years, being one of the most attractive forms of fuels to produce green energy. Cubic zirconia ceramics are considered promising catalytic supports, and the additive manufacturing of porous 3D structures based on these ceramics could enhance their catalytic performance. Herein, lightweight highly porous (up to 88%) 3D patterned 8 mol% yttria-stabilized cubic zirconia (8YSZ) scaffolds are manufactured by robocasting from pseudoplastic aqueous-based inks to produce catalytic supports for the hydrogen (H2) production. These scaffolds are thermally treated at temperatures ranging between 1000 and 1400 ◦C and, hence, mechanically and electrically characterized. 3D 8YSZ structures sintered at 1200 ◦C, with an appropriate balance between high porosity (86%) and compressive strength (3.7 MPa), are impregnated with palladium (Pd) catalytic nanoparticles and employed in the catalytic dehydrogenation of renewable formic acid (FA) using a fixed-bed reactor. 3D Pd/8YSZ catalyst leads to the continuous production of CO-free H2 with a FA conversion of 32% at T = 55 ◦C., Proyectos RTI2018-095052-B-I00, PID2019-105079RB-I00, PID2021-125427OB-I00 EIN2020-112153, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modelling the anisotropic thermal conductivity of 3D logpile structures

  • Moreno-Sanabria, Luis
  • Barea, Rafael
  • Osendi, María Isabel
  • Belmonte, Manuel
  • Miranzo López, Pilar
[EN] Assessing and predicting the thermal conductivity (κ) of macroporous materials is particularly important for additive manufactured 3D structures, as they offer considerable potential for tuning architectures and properties. In this work, finite element methods (FEM) are used to simulate the transient plane source test in 3D logpile lattices, approaching the effect of interfacial thermal contact resistances on κ measurement. Besides, the influence of different geometrical parameters (rod diameter, macropore size and overlapping between rods in consecutive layers) and the κ of the strut material on the anisotropic thermal conductivity of 3D lattices are investigated. The models are validated using experimental data for 3D composite structures of γ-Al2O3 with graphene nanoplatelet contents up to 18 vol%, as well as with reported data for alike scaffolds, all printed by robocasting. Results have strong impact for the application of novel 3D structures in energy production and storage, catalysis and heat transfer-related fields., This work was supported by the Spanish Ministry of Science and Innovation through RTI2018-095052-B-I00 and PID2021-125427OB-I00 (MICINN/AEI/FEDER, UE) and EIN2020-112153 (MICINN/AEI/10.13039/501100011033) projects, the latter also supported by the European Union through “NextGenerationEU/PRTR”. L. M.-S. acknowledges the financial support from MICINN/AEI/FEDER through the FPI contract Ref. PRE2019-091429 (2019 call)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Protein adsorption and in vitro behavior of additively manufactured 3D-silicon nitride scaffolds intended for bone tissue engineering

  • Sainz Trigo, M. Antonia
  • Serena Palomares, Sara
  • Belmonte, Manuel
  • Osendi, María Isabel
[EN] Highly porous scaffolds of SiN are fabricated by direct ink writing method (Robocasting) with a pattern of macroporous cavities of 650–700 μm. Two different SiN ink compositions regarding the oxide sintering aids (namely, YO, AlO, and SiO) are tried. Both inks reach solid volume fractions of ~0.40 with about 10–12 wt% of polymeric additive content that imparts the necessary pseudoplastic characteristics. The printed structures are sintered under controlled N atmosphere either in a conventional graphite furnace or by the spark plasma sintering technique. Skeleton of the scaffolds reaches densities above 95% of the theoretical value with ≈18–24% of linear shrinkage. Analysis of the crystalline phases, microstructure and mechanical properties are comparatively done for both compositions. The bioactivity of these structures is addressed by evaluating the ion release rate in simulated body fluid. In parallel, atomic force microscopy is used to determine the effect of the filaments surface roughness on protein adsorption (Bovine Serum Albumin) for assessing the potential application of 3D-SiN scaffolds in bone regeneration., Authors declare that there are no conflicts of interests. This work was supported by MICINN (Spain)/FEDER (UE) with projects: MAT2015-67437-R and RTI2018-095052-B-100
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D printing of cordierite materials from raw reactive mixtures

  • Dorado, B.
  • Moreno-Sanabria, Luis
  • García, E.
  • Belmonte, Manuel
  • Miranzo López, Pilar
  • Osendi, María Isabel
[EN] Porous cordierite materials are 3D printed by robocasting from two kaolin containing raw materials mixtures. Water suspensions of both mixtures at variable solid concentrations (40–67 wt%) are characterized by rheological measurements, showing good printability for concentrations >60 wt% without the need of any printing additive. The mixtures react during sintering (at 1250 °C) giving indialite as the main phase in the structures, which differ in minor phases. Three types of lattices are printed for both compositions with a logpile inner structure. Properties of interest like the coefficient of thermal expansion (CTE), the thermal conductivity (K) and the compression strength (σ) of the printed cordierites are determined and compared with published data. Results evidence that printing of clay containing reactive mixtures is a straightforward and cost-effective way to achieve porous complex shaped cordierite with CTE∼ 2–3 x10 K, K ∼ 0.4–0.6 W m K and maximum σ of 24 MPa., This work was supported by the Spanish Government through projects RTI2018-095052-B-I00 (MICINN/AEI/FEDER, UE) and EIN2020- 112153 (MCINN/AEI/10.13039/501100011033), the latter also supported by the European Union through “Next Generation EU/PRTR”. L. M.S. acknowledges the financial support from MICINN/AEI/FEDER through the FPI contract Ref. PRE2019-091429 (2019 call)., Supplementary data to this article can be found online at https://doi.org/10.1016/j.ceramint.2022.09.343, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and properties of Zn and Zn–Mg-doped tricalcium phosphates obtained by Spark Plasma Sintering

  • Sainz Trigo, M. Antonia
  • Serena Palomares, Sara
  • Caballero Cuesta, Ángel
[EN] β-tricalcium phosphate (Ca(PO) or TCP) are essential biomaterials because of the chemical composition, high biocompatibility and osseointegration. However, their limited mechanical properties restrict their use to areas where high mechanical performances are not required. Spark Plasma Sintering (SPS) was selected out of the unconventional sintering methods in order to obtain high-density doped-TCP bioceramic materials. The main advantages of SPS are a high heating rate, low sintering temperatures and short residence times, producing bioceramics with full density and fine-grain microstructure. The main purpose was to design, obtain by SPS and characterize undoped β-TCP, 1ZnO-doped β-TCP and 1ZnO-1MgO codoped β-TCP (wt. %) bioceramics. All the obtained samples were visually semitransparent and mainly β-TCP was detected by X-ray analysis. Densification behavior was determined by Archimedes' method and microstructural features of the sintered specimens were analyzed by Field Emission Scanning Electron Microscopy (FE-SEM-EDX). The undoped and doped β-TCP bioceramics were mechanically characterized, specifically the modulus of elasticity and Vickers microhardness. The results are compared with equivalent samples obtained by conventional solid-state sintering (CS) reaction. A first study of biological behavior was carried out, specifically direct cell adhesion of MG-63 human osteoblast-like cells on the polished surfaces of β-TCP, 1ZnO-β-TCP and 1ZnO–1MgO-β-TCP dense samples were determined. The present study concludes that the SPS process together with the doping effect enhanced sinterability, mechanical and biological properties of Zn-TCP and Zn–Mg-TCP based materials., This work is supported by the MICINN (Spain) with project CSIC 2017–60E028 and MCIU/AEI/FEDER (UE) with project RTI2018-095052-B-100.