Pasar al contenido principal

CONTRIBUCION DEL ALMACENAMIENTO DE ENERGIA TERMICA A LA EFICIENCIA ENERGETICA EN EDIFICIOS Y EN APLICACIONES INDUSTRIALES

ENE2008-06687-C02-02

•
Nombre agencia financiadora Ministerio de Ciencia e Innovación
Acrónimo agencia financiadora MICINN
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2008
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Subdirección General de Proyectos de Investigación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA
Identificador persistente http://dx.doi.org/10.13039/501100004837

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Performance characterization of a PCM storage tank

  • López Navarro, Alejandro
  • Biosca Taronger, Javier
  • Corberán Salvador, José Miguel
  • Peñalosa, C.
  • Lázaro, A.
  • Dolado, P.
  • Payá-Herrero, Jorge|||0000-0003-2663-3191
This paper presents the experimental results of a versatile latent heat storage tank capable of working with organic phase-change materials within a temperature range from -10 °C to 100 °C. The tank contains a paraffin with a phase-change temperature between 3 °C and 8 °C. Firstly, this study focuses on explaining the design criteria which were followed to build the tank. Secondly, a full experimental characterization of the performance has been carried out. The enthalpy temperature curve, the specific heat and density have been measured for the tested paraffin. The performance of the tank has been analyzed in terms of the vertical stratification within the PCM, the effectiveness, the reacted fraction and the total heat transfer of the tank. The results indicate that up to 78% of the maximum capacity is reached within 4 h. The performance is mainly controlled by the supply temperature and the effect of the mass flow rate is almost negligible given that all the tests are in laminar flow., The authors from the Polytechnic University of Valencia gratefully acknowledge ACCIONA Infraestructuras for the funding of the LHTS installation. The authors from University of Zaragoza would like to thank the Spanish Government for the partial funding of this work within the framework of research projects ENE2008-06687-C02-02 and ENE2011-28269-C03-01.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

IEA SHC Task 42 / ECES Annex 29 - Working Group B: Applications of Compact Thermal Energy Storage

  • Van Helden, W
  • Yamaha, M
  • Rathgeber, C
  • Hauer, A
  • Huaylla, F
  • Le Pierrès, N
  • Stutz, B
  • Mette, B
  • Dolado, P
  • Lazaro, A
  • Mazo, J
  • Dannemand, M
  • Furbo, S
  • Campos-Celador, A
  • , Diarce, G
  • Cuypers, R
  • König-Haagen, A
  • Höhlein, S
  • Brüggemann, D
  • Fumey, B
  • Weber, R
  • Köll, R
  • Wagner, W
  • Daguenet-Frick, X
  • Gantenbein, P
  • Kuznik, F
The IEA joint Task 42 / Annex 29 is aimed at developing compact thermal energy storage materials and systems. In Working Group B, experts are working on the development of compact thermal energy storage applications, in the areas cooling, domestic heating and hot water and industry. The majority of application projects were in the field of room heating and domestic hot water. In this article, an overview is given of a large number of applications. The storage technologies used in the applications are latent heat storage, open and closed solid sorption, liquid sorption and salt hydrates and composites thereof. On a broad front, a lot of progress was made in the development of components and systems, providing knowledge and experience regarding the design, numerical modeling, building, testing and economical assessing of components and storage systems. Most important findings are that the interaction of storage materials with the materials of components can be deciding for the technical feasibility, that a number of components, like reactor, heat exchangers and evaporators are less understood than initially thought and need more development, that the inclusion of storage materials in systems generate new challenges like the occurrence of non-condensable gases and thermo-mechanical effects and that standardized and simplified system approaches are needed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

IEA SHC Task 42 / ECES Annex 29 - A Simple Tool for the Economic Evaluation of Thermal Energy Storages

  • Rathgeber, C
  • Hiebler, S
  • Lävemann, E
  • Dolado, P
  • Lazaro, A
  • Gasia, J
  • De Gracia, A
  • Miró, L
  • Cabeza, L.F
  • König-Haagen, A
  • Brüggemann, D
  • Campos-Celador, Á
  • Franquet, E
  • Fumey, B
  • Dannemand, M
  • Badenhop, T
  • Diriken, J.j
  • Nielsen, J.E.
  • Hauer, A
Within the framework of IEA SHC Task 42 / ECES Annex 29, a simple tool for the economic evaluation of thermal energy storages has been developed and tested on various existing storages. On that account, the storage capacity costs (costs per installed storage capacity) of thermal energy storages have been evaluated via a Top-down and a Bottom-up approach. The Top-down approach follows the assumption that the costs of energy supplied by the storage should not exceed the costs of energy from the market. The maximum acceptable storage capacity costs depend on the interest rate assigned to the capital costs, the intended payback period of the user class (e.g. industry or building), the reference energy costs, and the annual number of storage cycles. The Bottom-up approach focuses on the realised storage capacity costs of existing storages. The economic evaluation via Top-down and Bottom-up approach is a valuable tool to make a rough estimate of the economic viability of an energy storage for a specific application. An important finding is that the annual number of storage cycles has the largest influence on the cost effectiveness. At present and with respect to the investigated storages, seasonal heat storage is only economical via large sensible hot water storages. Contrary, if the annual number of storage cycles is sufficiently high, all thermal energy storage technologies can become competitive.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Experimental analysis of a microencapsulated PCM slurry as thermal storage system and as heat transfer fluid in laminar flow

  • Delgado, M.
  • Lázaro, A.
  • Mazo, J.
  • Marín J. M.
  • Zalba, B.
microencapsulated PCM (Phase Change Material) slurry is a dispersion where the PCM, microencapsulated by a polymeric capsule, is dispersed in water. Compared to water, these new fluids have a higher heat capacity during the phase change and a possible enhancement, as a result of this phase change, in the heat transfer phenomenon. From the literature review, the existing experimental results are found incomplete and contradictory in many cases. For this reason the objective of this investigation is to analyze the heat transfer phenomenon in mPCM slurries, proposing a new methodology, developed by the authors. In this manner, an experimental analysis using a slurry with a 10% weight concentration of paraffin has been conducted to study it as a thermal storage material and as a heat transfer fluid. The results demonstrated an improvement of approximately 25% on the convective heat transfer coefficient when compared to water.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Review on phase change material emulsions and microencapsulated phase change material slurries: Materials, heat transfer studies and applications

  • Delgado, Mónica
  • Lázaro, Ana
  • Mazo, Javier
  • Zalba, Belén
Phase change materials (PCM) in the form of slurries have had an increasingly important role as heat transfer fluids and as thermal energy storage media. Although it is a recent technology in the field of thermal energy storage with phase change materials, the volume of literature begins to be significant. This investigation carries out a compilation of information on two latent thermal fluids: PCM emulsions and microencapsulated PCM slurries (mPCM slurries). This review presents tables containing information on the different PCM emulsions and mPCM slurries studied by different researchers, as well as commercially available products. Thermophysical and rheological properties are analyzed, making a special effort to analyze heat transfer phenomena, concluding with the enumeration of application examples available in literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Analysis of the physical stability of PCM slurries

  • Delgado, M.
  • Lázaro, A.
  • Peñalosa, C.
  • Mazo, J.
  • Zalba, B.
Microencapsulated phase change material slurry (mPCM slurry) is a latent heat storage fluid in which the PCM microparticles have been dispersed in water. One of the main issues to be tackled is its lack of physical stability, since stratification problems tend to occur. Generally, an unstabilization process in PCM slurries can take weeks or even months. To predict the physical stability of PCM slurries without having to wait so long, a methodology well known in the food and pharmaceutical fields has been applied. This methodology basically consists of measuring samples with a rheometer in oscillatory mode. These measurements can be related to visually obtained measurements of the unstabilization process of creaming, specifically with the creaming percentage over time. From the frequency sweeps accomplished, an exponential relationship between the creaming percentage and the elastic module of the PCM slurries have been obtained. From the strain sweeps, the cohesive energies of the PCM slurries have been calculated and related to the creaming percentage, observing a linear relationship. In this way, the dominant parameters in the unstabilization process have been obtained which manufacturers can modify in order to improve the physical stability of PCM slurries.