Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 318
Encontrada(s) 4 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Characterization of granular phase change materials for thermal energy storage applications in fluidized beds

  • Izquierdo Barrientos, María Asunción
  • Sobrino Fernández, Celia
  • Almendros Ibáñez, José Antonio
  • Barreneche, C.
  • Ellis, Noko
  • Cabeza, L. F.
This work investigates commercially available granular phase change materials (PCMs) with different transition temperatures for the use of thermal-energy storage systems in fluidized beds. The hydrodynamic characteristics of granular PCMs were tested in cylindrical-3D and planar-2D fluidized beds. The density, particle size distribution and angle of repose were measured for various PCM materials. Further attrition studies were conducted with changes in particle surface from abrasion, which were characterized using a Scanning Electron Microscope (SEM). The results indicate that some materials with smaller particle size and thinner supporting structure can lose the paraffin during the fluidization process, when paraffin is in a liquid state. As a consequence, the particles agglomerate, and the bed defluidizes. For all of the tested materials, only GR50 (with a transition temperature of 50 degrees C) properly fluidizes when the paraffin is in the liquid state and has shown to endure >75 h of continuous operation and 15 melting-solidification cycles in a fluidized bed. Additional differential scanning calorimetry (DSC) measurements of the cycled particles did not show a decrease in energy storage capacity of the granular PCM, which corroborates that there is no loss of material after >75 h of fluidization. (C) 2016 Elsevier Ltd. All rights reserved., The work is partially funded by the Spanish government (ENE2010-15403, ENE2011-22722 and ENE2015-64117-C5-1). The authors would like to thank the Catalan Government for the quality accreditation to their research groups GREA (2014 SGR 123). The study that led to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of the filler on the nanomechanical properties of polypropylene in contact with paraffinic phase change material

  • Giro-Paloma, J.
  • Rayón Encinas, Emilio
  • Roa, J. J.
  • Martínez, M.
  • Fernández, A. I.
[EN] As the changes on the mechanical properties with depth of indentation provide valuable information that may be suitable for design purposes, nanoindentation is an adequate technique for investigating the nanomechanical changes in the surface and in the inner polymers. This research focuses on the study of the nanomechanical properties of two grades of polypropylene (PP) after the long term exposure to an organic fluid, such as paraffin wax used as a phase change materials (PCM). PCM are used for thermal energy storage (TES) in buildings applications for passive systems or heating and cooling usages. In any of these uses PCM must be encapsulated and PP is a possibility within the container materials used. Four different samples of the polypropylene were evaluated: PP, filled polypropylene with 60% Mg(OH)2 (PP-60Mg), PP-60Mg with PCM (RT-25), and PP-60Mg with PCM (RT- 42). It was studied the thermal stability by Thermogravimetrical analysis of these samples, and also it was evaluated the Hardness (H), Elastic modulus (E) and Loss modulus (Eloss) for the unfilled PP and PP-60Mg in contact with two different PCM at different temperatures (30 C, 45 C and 60 C for RT-25 and 45 C for RT-42) for 32 days. Results show that the mechanical properties H, E, and Eloss are higher for PP-60Mg than for PP. Nevertheless, these properties decrease significantly when the PP and the PP-60Mg are in contact with PCM, because it acts as a plasticizer, softening the polymer. Besides, the higher PCM s melting point, the lowest mechanical properties were observed. (C) 2014 Elsevier Ltd. All rights reserved., The authors would like to thank the CCP for their kindly supply of the polymeric samples. The work is partially funded by the Spanish government (ENE2011-28269-C03-02). The authors would like to thank the Catalan Government for the quality accreditation given to their research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement no PIRSES-GA-2013-610692 (INNOSTORAGE).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Thermal characterization of buildings from the monitoring of the AC system consumption

  • Payá-Herrero, Jorge|||0000-0003-2663-3191
  • Corberán Salvador, José Miguel
  • de Gracia, Alvaro
  • Castell, Albert
  • Cabeza, Luisa Fernanda
[EN] This work presents a comparative study between two buildings or cubicles with a same geometry and orientation but with different constructive layers. The mineral wool cubicle is more insulated whereas the alveolar cubicle has more thermal inertia. A novel point in this study has been to evaluate indirectly the thermal load based on the energy consumption of the heat pumps. The results indicate that the mineral wool cubicle consumes up to 7.3% less energy consumption than the alveolar cubicle, particularly in summer. In fact, the load in summer is up to 11.6% higher with the alveolar cubicle, which gains more solar energy during daytime due to its inertia. The power consumption is practically aligned with the outdoor temperatures since it is very sensitive to the operating temperatures. Nevertheless, the peak building load can take place up to 5 hours later than the peak outdoor temperature, particularly in summer and in the alveolar cubicle. Finally, the proposed approach has helped obtained in-situ U-values of 0.20-0.27 W m−2 K−1 for both cubicles., The work partially funded by the Spanish government (ULLE10-4E-1305). The authors from Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE). This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Alvaro de Gracia would like to thank the Education Ministry of Chile for Grant PMI ANTI 201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Composite gypsum containing fatty-ester PCM to be used as constructive system: Thermophysical characterization of two shape-stabilized formulations

  • Serrano, Susana
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
Gypsum board containing a shape-stabilized PCM either as a sheet or as pellets is thermo-physically characterized. The main objective is to elucidate which is the most efficient way to introduce the PCM into gypsum boards by measuring the thermal transmittance, effective thermal conductivity, total heat accumulated, and the average heat capacity. At their light it can be concluded that a gypsum board containing 25% PCM is more thermally insulating than the gypsum without PCM, and the average heat capacity of the samples containing sheet-PCM and pellets-PCM are higher than the gypsum by itself due to the latent heat effect, being 41% and 33% respectively., The work is partially funded by the Spanish government (ENE2011-28269-C03-02). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007–2013) under grant agreement n◦ PIRSESGA-2013-610692 (INNOSTORAGE)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Materials and system requirements of high temperature thermal energy storage systems: A review. Part 2: thermal conductivity enhancement techniques

  • Gasia, Jaume
  • Miró, Laia
  • Cabeza, Luisa F.
This review is focused on the study of the requirement of high thermal conductivity of thermal energy storage (TES) materials and the techniques used to enhance it as this is one of the main obstacles to achieve full deployment of TES systems. Numerical and experimental studies involving different thermal conductivity enhancement techniques at high temperature (>150 °C) are reviewed and classified. This article complements Part 1, which reviews the different requirements that TES materials and systems should consider for being used for high temperature purposes and the approaches to satisfy them. The enhancements identified for this temperature range are the addition of extended surfaces like fins or heat pipes and the combination of highly conductive materials with TES material like graphite or metal foam composites and nanomaterials. Moreover the techniques presented are classified and discussed taking into account their research evolution in terms of maturity and publications., The work is partially funded by the Spanish Government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). The research leading to these results has received funding from the European Union׳s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Green facade for energy savings in buildings: The influence of leaf area index and facade orientation on the shadow effect

  • Pérez Luque, Gabriel
  • Coma Arpón, Julià
  • Sol i Felip, Salvador
  • Cabeza, Luisa F.
To “green” building envelopes is currently one of the most promising ways to provide energy savings in buildings and to contribute to the urban heat island effect mitigation. The shadow effect supplied by plants is the most significant parameter for this purpose. One way to characterize the potential shadow effect of greenery is to calculate the facade foliar density by means of the leaf area index (LAI). As LAI is commonly used in horizontal crops, their use in vertical greenery systems (VGS) has generated dispersion and uncertainty in previous studies both in terms of methodologies and results obtained. In addition, a lack of data relating to the influence of the facade orientation in the final contribution of vertical greenery to the energy savings has been observed in previous studies. This study aims at establishing a common and easy way to measure LAI and to lick it to the energy savings provided by VGS. Moreover, the energy savings achieved as well as the influence of facade orientation on the final thermal behaviour of two different VGS, a double-skin green facade and a green wall, was studied. From the results, it can be stated that the most simple and quick procedure to measure LAI in order to characterize the foliar density of VGS is the indirect method based on the amount of light transmitted through the green screen. From the experimental tests interesting energy savings were obtained (up to 34% for Boston Ivy pant specie with a LAI of 3.5–4, during summer period under Mediterranean continental climate). Moreover, the dependence on facade orientation was confirmed with representative contribution over the whole energy savings from East and West orientation., The work partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and to the city hall of Puigverd de Lleida. This projects has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Julià Coma would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermogravimetric study of a phase change slurry: effect of variable conditions

  • Giro-Paloma, Jessica
  • Valle-Zermeño, Ricardo del
  • Fernández Renna, Ana Inés
  • Chimenos Ribera, Josep Ma.
  • Formosa, Joan
Microcapsules containing Phase Change Materials (MPCM) are widely used for passive systems in energy storage. When MPCM are mixed with a carrier fluid, Phase Change Slurries (PCS) are used for heat transfer fluids in active systems or heat transport systems. The thermal behavior of PCS can be measured as dry or wet basis, resulting in important differences in weight losses. This study explores the optimum conditions for analyzing the thermal behavior of dried PCS by thermogravimetric analysis (TGA) varying the parameter conditions for obtaining peak temperature and heat flow (latent heat). The factors that were taken into account were the atmosphere of study (air and nitrogen) and the heating rate (0.5, 1, 5, and 10 °C·min−1). The best conditions to determine peak temperature are at 1 °C·min−1 and in N2 atmosphere, whereas the decomposition fusion/latent heat of the sample is improved at higher heating velocities towards 10 °C·min−1., The work is partially funded by the Spanish government (ENE2015-64117-C5-2R). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Ricardo del Valle Zermeño is grateful to the Government of Catalonia for the research grant (FI-DGR 2014). The authors would like to thank the Catalan Government for the quality accreditation given to their research group DIOPMA (2014 SGR 1543).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Influence of alkaline chlorides on thermal energy storage properties of bischofite

  • Ushak, Svetlana
  • Gutiérrez, Andrea
  • Galazutdinova, Yana
  • Barreneche Güerisoli, Camila
  • Cabeza, Luisa F.
  • Grágeda, Mario
Brines coming from salted lakes such as that at the Atacama desert in Chile produce by-products or wastes which today are stored in the nearby from the production areas. Bischofite is one of those by-products, and therefore, its composition may vary from batch to batch. Because bischofite has been identified as a good candidate to be used as phase change material (PCM) for latent heat thermal energy storage, the influence of the variation of bischofite composite with its main impurities in this potential used needs to be evaluated. The main impurities of bischofite are the cations sodium, potassium and lithium and the anions chloride and sulfate. The results of this investigation established that the presence of KCl and NaCl in bischofite (up to 5 wt%) does not affect its use as PCM, because its melting enthalpy and temperature do not vary significantly. It is interesting that small contents of LiCl in bischofite do not change significantly its melting enthalpy but decrease the melting temperature. Such change may enable the usage of this material as PCM in other applications at lower temperatures., The work at the University of Antofagasta was supported by CONICYT/FONDAP no. 15110019, and the Education Ministry of Chile Grant PMI ANT 1201. Andrea Gutierrez would like to acknowledge support from CONICYT/PAI no. 7813110010 and Education Ministry of Chile for her postdoctorate scholarship ANT 1106. Yana Galazutdinova would like to acknowledge support from CONICYT-PCHA/Doctorado Nacional para Estudiantes Extranjeros 2014/Folio 63140052 for her doctorate scholarship. The authors from the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement no PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement no. 657466 (INPATH-TES).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Embodied energy and cost of high temperature thermal energy storage systems for use with concentrated solar power plants

  • Jacob, Rhys
  • Belusko, Martin
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Saman, Wasim
  • Bruno, Frank
The intermittency of renewable energy systems remains one of the major hurdles preventing a large scale uptake of these technologies and concentrated solar power (CSP) systems are no different. However, CSP has the benefit of being able to store excess heat using thermal energy storage (TES). For the uptake of CSP with TES it must be demonstrated that the technology is both economically as well as environmentally feasible. This paper aims to investigate the economic and environmental impact of several TES options that are available for CSP systems. The investigated systems include an encapsulated phase change material (PCM) system, a coil-in-tank PCM system and a liquid sodium TES system. The economic impact in the current study refers to the capital cost (CAPEX) of each system including the tank, storage material, encapsulation cost (if applicable) and allowances for construction and engineering. The environmental impact of each system is accounted by calculating the embodied energy of each of the system components. Each storage system will be required to store a comparable amount of energy so that reliable conclusions can be drawn. The results from this analysis conclude that the encapsulated PCM (EPCM) and coil-in-tank system represent an embodied energy of roughly one third of the corresponding state-of-the-art two-tank molten salt system. Furthermore, the EPCM and coil-in-tank systems result in CAPEX reductions of 50% and 25% over the current state-of-the-art two-tank molten salt system. The liquid sodium system was found to result in higher embodied energy and CAPEX than any previously studied TES system. Finally, the advantages and disadvantages of each system was discussed and compared to previous literature., This research was performed as part of the Australian Solar Thermal Research Initiative (ASTRI), a project supported by the Australian Government, through the Australian Renewable Energy Agency (ARENA). The work is partially funded by the Spanish Government (ENE2015-64117-C5-1-R and ENE2015-64117-C5-2-R). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación

Lithium in thermal energy storage: a state-of-the-art review

  • Cabeza, Luisa F.
  • Gutiérrez, Andrea
  • Barreneche Güerisoli, Camila
  • Ushak, Svetlana
  • Fernández, Ángel G.
  • Fernández Renna, Ana Inés
  • Grágeda, Mario
Lithium, mainly used in electrical energy storage, has also been studied in thermal energy storage. It is recognized as a"critical material" and is produced from minerals and from brines. Chile is one of the biggest producers, here from brine and with lower costs than in other countries. With sensible heat storage, in solar power plants lithium is seen as a way to improve the properties of molten salts used today. The low melting point in these ternary salts with lithium, represent a considerable reduction in the maintenance and operational costs associated with current solar technology, demonstrating that the fluids showed, are potential candidates for thermal energy storage (TES) in concentrated solar plants (CSP) plants. Many materials have been studied and proposed to be used as phase change materials (PCM). Between the multiple materials studied to be used in PCM, lithium materials and mixtures are listed as potential PCM for building applications and for high temperature applications. In thermochemical energy storage, lithium compounds have been used mainly in chemical heat pumps, following their use in absorption cooling., This work was partially funded by the Spanish ProjectENE2011-22722 and ENE2011-28269-C03-02. The research leading to these results has received funding from the European Union׳s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Dr. Luisa F. Cabeza would like to acknowledge the Generalitat de Catalunya for the quality recognition 2014-SGR-123 and Dr. A. Inés Fernández for 2014-SGR-1543. The authors acknowledge to FONDECYT (grant no. 1120422), FONDAP SERC-Chile (grant no. 15110019), and the Education Ministry of Chile Grant PMI ANT 1201 for the financial support. Andrea Gutierrez would like to acknowledge to the Education Ministry of Chile her doctorate scholarship ANT 1106.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Energy savings due to the use of PCM for relocatable lightweight buildings passive heating and cooling in different weather conditions

  • Marín, Paula E.
  • Saffari Tabalvandani, Mohammad
  • Gracia Cuesta, Alvaro de
  • Zhu, Xibingyan
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
  • Ushak, Svetlana
Relocatable, transportable or off-site constructed lightweight buildings typically undergo sharp indoor temperature fluctuations in the heating and cooling seasons due to the lack of sufficient thermal mass in their envelopes, resulting in high energy consumption to provide the zone with comfort temperature. The application of phase change materials has been suggested as a promising solution to control the indoor thermal condition in buildings. This work is an attempt to support the application of PCM technology in lightweight relocatable buildings as a passive alternative to save energy under different weather conditions. The numerical results highlighted the potential of using PCM-enhanced gypsum boards in lightweight buildings to increase the energy performance during both heating and cooling seasons in arid and warm temperate main climate areas., The authors from Chile acknowledge to CONICYT/FONDAP No. 15110019. This work has been partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Paula Marin thanks fellowship CONICYT-PCHA/doctorado nacional/2015-21151359.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Use of multi-layered PCM gypsums to improve fire response. Physical, thermal and mechanical characterization

  • Serrano, Susana
  • Barreneche Güerisoli, Camila
  • Navarro Ezquerra, Antonia
  • Haurie, Laia
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
The building sector is one of the highest energy consumers representing around 30% of total energy use. One of the recommendations of the IEA (International Energy Agency) to reduce energy consumption in buildings is to enhance the thermal performance of building envelopes. In the present study, PCM (Phase Change Material) gypsum materials have been manufactured using three different PCM inclusion methods and a thin layer of gypsum without PCM is added as external layer with the aim of improving the fire reaction behaviour. By performing a detailed physical, mechanical and thermal characterization, the suitability of the materials to be implemented in the building envelope as inner coating is demonstrated. Results show that also the thermal properties are improved in the three cases by the addition of PCM. Moreover, the negative effect of adding paraffin wax PCM into gypsum against flame can be easily reduced by the addition of a thin gypsum layer, which is a low tech and cheap solution without extra environmental impact., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R, ENE2015-64117-C5-2-R, MAT2011-26410 and BIA2014-52688-R). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA - UdL (2014 SGR 123) and research group DIOPMA - UB (2014 SGR 1543) and GICITED − UPC (2014 SGR 1298). In addition, this project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental investigation of the effect of dynamic melting in a cylindrical shell-and-tube heat exchanger using water as PCM

  • Gasia, Jaume
  • Tay, N. H. Steven
  • Belusko, Martin
  • Cabeza, Luisa F.
  • Bruno, Frank
In the present paper, an experimental study is carried out to evaluate the effect of the dynamic melting concept in a cylindrical shell-and-tube heat exchanger using water as the phase change material (PCM) and a potassium formate/water solution as the heat transfer fluid (HTF). The dynamic melting concept is a new heat transfer enhancement technique which consists of recirculating the liquid PCM during the melting process with a pump and thus increasing the overall heat transfer coefficient as a result of the dominance of the forced convection. The HTF flow rate was kept constant at 1 l/min and four different PCM flow rates of 0, 0.5, 1 and 2 l/min were tested. Results from the experimental analysis showed enhancements up to 65.3% on the melting period, up to 56.4% on the effectiveness, and 66% on the heat transfer rates when the PCM flow rate was twice the HTF flow rate. From these experiments, it can be concluded that dynamic melting is an effective technique for enhancing heat transfer during melting of PCM., The authors acknowledge the South Australian Department of State Development who have funded this research through the Premier’s Research Industry Fund - International Research Grant Program (IRGP 33). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B 00047). The work is partially funded by the Spanish Government (ENE2015-64117-C5-1-R). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal performance evaluation of bischofite at pilot plant scale

  • Gasia, Jaume
  • Gutiérrez, Andrea
  • Peiró Bell-lloch, Gerard
  • Miró, Laia
  • Grágeda, Mario
  • Ushak, Svetlana
  • Cabeza, Luisa F.
The selection of the proper thermal energy storage (TES) material for an application is crucial. On the one hand, these materials should have suitable thermal properties for the operational temperatures range of the systems they are planned to work for, such as thermal stability, high latent heat and high heat capacity. On the other hand, they should be available on the market and at low price. Besides, researchers have to bear in mind the importance of testing TES materials not only at laboratory scale but also at higher scale, since it has been demonstrated that some thermal characteristics are volume-dependant. In the present study, bischofite, a by-product obtained from the non-metallic industry in the North of Chile with desired thermal properties for mid-temperature applications (around 100 C), has been studied. A first analysis was performed in terms of comparing the thermal properties and cost of bischofite with other material previously studied as TES materials in order to evaluate its potential in both latent and sensible phases. Afterwards, a second analysis was experimentally performed in terms of testing bischofite at large-scale (204 kg) in a pilot plant facility. The experimental procedure consisted on several charging processes within two different temperatures ranges: from 50 C to 80 C and from 80 C to 120 C in order to study the behavior of the material in the sensible solid phase and latent phase respectively. The temperature profiles, the power given by the HTF, the energy balance in the storage system and the accumulation energy rate of the bischofite were analyzed. Results of both analysis showed that bischofite has potential as TES material for mid-temperature applications., The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under Grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). The work was partially funded by the Spanish government (Project ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). The authors would like to acknowledge the collaboration of the company SALMAG. The authors acknowledge to FONDECYT (Grant No 1120422), CONICYT/FONDAP No 15110019, and the Education Ministry of Chile Grant PMI ANT 1201 for the financial support. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Andrea Gutierrez would like to thank to the Education Ministry of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI NO 7813110010.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Compatibility of materials for macroencapsulation of inorganic phase change materials: experimental corrosion study

  • Ushak, Svetlana
  • Marín, Paula E.
  • Galazutdinova, Yana
  • Cabeza, Luisa F.
  • Farid, Mohammed M.
  • Grágeda, Mario
The potential of the use of salt hydrates MgCl2·6H2O (bischofite) with typical impurities of the Salar de Atacama as a thermal energy storage material was evaluated with special attention to its corrosion behavior. Bischofite behavior is compared with that of commercial salt MgCl2·6H2O. The corrosion tests were conducted with metal sheets (copper, aluminum and stainless steel) partially immersed in molten salt hydrates at a temperature of 120 °C during 1500 h. The results showed minimum corrosion on all the immersed surfaces of all the metals. However, very sever corrosion was observed at the salt/air interface due to a known phenomenon of oxygen enhanced corrosion usually found even with water at ambient temperature. The corrosion products were determined with scanning electron microscopy (SEM-EDX) and X-ray diffraction (XRD) technique. For salts hydrates bischofite and MgCl2·6H2O, the results show the formation of cuprite (Cu2O) and hematite (Fe2O3) on copper and stainless steel samples, respectively. For all cases studied in the present work, several chloride compounds were identified as corrosion products., The authors would like to acknowledge the collaboration of the company SALMAG. The authors acknowledge to CONICYT/FONDAP No. 15110019, and the Education Ministry of Chile Grant PMI ANT 1201 for the financial support. P. Marin thanks fellowship CONICYT-PCHA/doctorado nacional/2015-21151359. Y. Galazutdinova thanks fellowship CONICYT-PCHA No. 63140052. This work was partially funded by the Spanish project ENE2011-22722. Dr. Luisa F. Cabeza would like to acknowledge the Generalitat de Catalunya for the quality recognition 2014-SGR-123. The research leading to these results has received funding from the European Commission Seventh Framework Programme(FP/2007-2013) under grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

High density polyethylene spheres with PCM for domestic hot water applications: Water tank and laboratory scale study

  • Navarro Farré, Lidia
  • Barreneche Güerisoli, Camila
  • Castell, Albert
  • Redpath, David A.G.
  • Griffiths, Philip
  • Cabeza, Luisa F.
Renewable energy is a potential alternative energy provider with fewer CO2 emissions. However, the mismatch between energy supply and demand is the main disadvantage. Therefore, thermal energy storage becomes an essential technology for enhancing renewable energy efficiency and providing energy supply to the end user. In solar thermal energy systems, hot water tanks are widely used as sensible heat storage technology. Moreover, water storage usually requires large volumes and their improvement has been studied in terms of shape and arrangement. Latent heat storage materials are a potential technology for implementation in water storage tanks in order to reduce their volume and to enhance their efficiency. In this paper, the incorporation of shape high density polyethylene spheres with PCM into domestic hot water tanks is studied. Undesired results obtained in the water tank set-up lead the authors to analyse the PCM leakage in the laboratory. Laboratory analysis pointed out that the PCM-spheres must be thermally cycled and cleaned before their implementation in real application of domestic hot water in order to stabilize the PCM content inside the PCM- spheres., The work partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-2-R (MINECO/FEDER), and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Novel inorganic binary mixture for low‐temperature heat storage applications

  • Galazutdinova, Yana
  • Grágeda, Mario
  • Cabeza, Luisa F.
  • Ushak, Svetlana
In this study, an inorganic mixture based on bischofite (industrial by‐product) was developed and characterized for its application as a phase change material for low‐temperature thermal energy storage. The most appropriate composition was established as 40 wt% bischofite and 60 wt% Mg(NO3)2 · 6H2O. Thermophysical properties were defined and compared with those of the mixture with synthetic MgCl2 · 6H2O. The heat of fusion and melting temperature were measured as 62.0°C and 132.5 kJ kg−1 for the mixture with MgCl2 · 6H2O and 58.2°C and 116.9 kJ kg−1 for the mixture with bischofite. The specific heat capacity values, cycling, and thermal stability for both mixtures were also determined. For the mixture with MgCl2 · 6H2O, the densities of the solid and liquid states were 1517 kg m−3 (ambient temperature) and 1515 kg m−3 (at 60‐70°C), respectively. For the mixture with bischofite, the densities of the solid and liquid states were 1525 kg m−3 (ambient temperature) and 1535 kg m−3 (at 60‐70°C), respectively. Both mixtures show supercooling of about 23.4 and 34.1°C for the mixture with bischofite and MgCl2 · 6H2O, respectively. In addition, it was shown that supercooling may be reduced by increasing the quantity of material tested. Thereby, it was established that an inorganic mixture based on bischofite is a promising PCM for low‐temperature thermal energy storage applications., Funding informationComisión Nacional de InvestigaciónCientífica y Tecnológica, Grant/AwardNumber: CONICYT/FONDAP 15110019,CONICYT‐PCHA/Doctorado Nacional paraEstudiantes Extranjeros 2014/Folio63140052, ERANet‐LAC 2nd Joint Call,ERANET‐LAC 2015‐2016, projectELAC2015/T06‐0988; FONDECYT, Grant/Award Number: 1170675; Spanish Govern-ment, Grant/Award Number: ENE2015‐64117‐C5‐1‐R (MINECO/FEDER); CatalanGovernment, Grant/Award Number: GREA(2014 SGR 123); European CommissionSeventh Framework Programme, Grant/Award Number: PIRSES‐GA‐2013‐610692(INNOSTORAGE); European Union0s Hori-zon, Grant/Award Number: 657466(INPATH‐TES)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Methodologies to estimate industrial waste heat potential by transferring key figures: a case study for Spain

  • Miró, Laia
  • Brueckner, Sarah
  • McKenna, Russell
  • Cabeza, Luisa F.
In the current European energy context, the use of recovered industrial waste heat provides an attractive opportunity to substitute primary energy consumption by a low-emission and low-cost energy carrier. In the case of industrial waste heat, this potential is currently not only largely untapped, but also unaccounted for. In order to achieve a widespread use of recovered industrial waste heat, assessments with a large scope and high spatial resolution are needed. Three methods published in the period 2002–2010 have been found in the literature, which are potentially transferable to other regions. These three methods are based on either the energy consumption of each manufacturing sector or the individual site CO2 emissions. The scope of this analysis is, first, to investigate in how far a transfer of the figures to different countries or regions is sensible in comparison to former studies in the literature. In the process, some uncertainties when transferring methods were identified (different definitions of industry, different standard industrial activities classifications or no standard at all, etc.). The second goal is, once the methodology is accepted, to apply it to a case study, in this case the industrial sector in Spain and two of its counties (Catalonia and the Basque Country) for the years 2001, 2009, 2010 and 2013. In this period, and based on the different approaches employed, the Spanish annual industrial waste heat potential ranges from 54.3 to 151.1 PJ, Catalonia from 8.6 to 29.7 PJ, and from 7.2 to 11.9 PJ for the Basque Country. The methods are considered highly transferable but uncertainties inevitably arise in the case that the source and destination industrial sectors are very different., The work is partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305) and by BMWi Federal Ministry for Economic Affairs and Energy in Germany (Project FKZ 0327383B Mobile Sorption Heat Storage). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

CO2 mitigation accounting for Thermal Energy Storage (TES) case studies

  • Cabeza, Luisa F.
  • Miró, Laia
  • Oró Prim, Eduard
  • Gracia Cuesta, Alvaro de
  • Martin, Viktoria
  • Krönauer, Andreas
  • Rathgeber, Christoph
  • Farid, Mohammed M.
  • Paksoy, Halime Ö.
  • Martínez, Mònica
  • Fernández Renna, Ana Inés
According to the IPCC, societies can respond to climate changes by adapting to its impacts and by mitigation, that is, by reducing GHG emissions. No single technology can provide all of the mitigation potential in any sector, but many technologies have been acknowledged in being able to contribute to such potential. Among the technologies that can contribute in such potential, Thermal Energy Storage (TES) is not included explicitly, but implicitly as part of technologies such as energy supply, buildings, and industry. To enable a more detailed assessment of the CO2 mitigation potential of TES across many sectors, the group Annex 25 “Surplus heat management using advanced TES for CO2 mitigation” of the Energy Conservation through Energy Storage Implementing Agreement (ECES IA) of the International Energy Agency (AEI) present in this article the CO2 mitigation potential of different case studies with integrated TES. This potential is shown using operational and embodied CO2 parameters. Results are difficult to compare since TES is always designed in relation to its application, and each technology impacts the energy system as a whole to different extents. The applications analyzed for operational CO2 are refrigeration, solar power plants, mobile heat storage in industrial waste heat recovery, passive systems in buildings, ATES for a supermarket, greenhouse applications, and dishwasher with zeolite in Germany. The paper shows that the reason for mitigation is different in each application, from energy savings to larger solar share or lowering energy consumption from appliances. The mitigation potential dues to integrated TES is quantified in kg/MW h energy produced or heat delivered. Embodied CO2 in two TES case studies is presented, buildings and solar power plants., The work was partially funded by the Spanish government (project ENE2011-22722 and ENE2011-28269-C03-02). The authors would also like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE). The work of ZAE Bayern in the development of the mobile sorption heat storage was supported by the German Federal Ministry of Economics and Technology under the project code 0327383B. ZAE Bayern thanks the Bosch-Siemens-Hausgeräte GmbH for the fruitful collaboration in the development of a sorption storage for dishwashers.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermochemical energy storage by consecutive reactions for higher efficient concentrated solar power plants (CSP): Proof of concept

  • Cabeza, Luisa F.
  • Solé, Aran
  • Fontanet, Xavier
  • Barreneche Güerisoli, Camila
  • Jové, Aleix
  • Gallas, Manuel
  • Prieto, Cristina
  • Fernández Renna, Ana Inés
Concentrated solar power plants (CSP) combined with thermal energy storage (TES) offers the benefit to provide continuous electricity production by renewable energy feed. There are several TES technologies to be implemented, being the thermochemical energy storage the less studied and the most attractive since its volumetric energy density is 5 and 10 times higher than latent and sensible TES, respectively. Thermochemical energy storage technology is based on reversible chemical reactions, also named thermochemical materials (TCM). One of the main challenges of TCM is to achieve a proper reversibility of the reactions, which in practical conditions leads to lower efficiencies than the theoretically expected. A new concept based on changing from reversible TCM reactions towards TCM consecutive reactions aims to eliminate reversibility problems and therefore improve the overall efficiency. Consecutive TCM reactions can either be based in one cycle, where reactants are needed to feed the reaction, or two coupled cycles which offer the possibility to work without any extra mass reactants input. The plausibility of the implementation of both concepts in CSP is detailed in this paper and case studies are described for each one., The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007–2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Multi-objective optimization of thermal modelled cubicles considering the total cost and life cycle environmental impact

  • Carreras, Joan
  • Boer, Dieter
  • Guillén Gosálbez, Gonzalo
  • Cabeza, Luisa F.
  • Medrano Martorell, Marc
  • Jiménez, Laureano
Energy efficiency strategies, such as building insulation, improve the building performance without compromising comfort. This study presents a methodology for determining the optimal insulation thickness for external building surfaces. Our approach is based on a multi-objective optimization model that minimizes simultaneously the cost and environmental impact associated with both the energy consumption over the operational phase and the generation of the construction materials (including the waste produced during the disposal phase). The thermal loads of the cubicles were calculated with EnergyPlus, a widely used simulation program for buildings. The environmental impact was quantified following the life cycle assessment (LCA) methodology. Our approach was applied to a case study of a house-like cubicle located in Lleida (northeast Spain). Taking as a basis a standard cubicle without insulation, our approach identifies solutions that reduce around 40% both, the cost and environmental impact. Optimal solutions show also important economic and environmental improvements compared to cubicles constructed with the Spanish legislation requirements. Our method is intended to assist decision-makers in the design of buildings., The authors would like to acknowledge financial support from the Spanish Government (ENE2011-28269-C03-03, ENE2011-22722, DPI2012-37154-C02-02, CTQ2012-37039-C02) and to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123). The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Combining biocatalysts to achieve new phase change materials. Application to non-edible animal fat

  • Gallart-Sirvent, Pau
  • Martín, Marc
  • Solé, Aran
  • Villorbina Noguera, Gemma
  • Balcells Fluvià, Mercè
  • Cabeza, Luisa F.
  • Canela i Garayoa, Ramon
"Formerly known as Journal of Molecular Catalysis A: Chemical", The thermal properties of various alkyl threo-9, 10-dihydroxystearates (DHSEs) prepared from non-edible fat were studied. Non-edible animal fat was hydrolyzed in a 93% yield with R. oryzae resting cells. Crude unsaturated fatty acids were recovered from the matter liquor resulting from a crystallization performed to achieve the saturated fatty acids. These unsaturated free fatty acids were epoxidized with 30% H2O2 using immobilized Candida antarctica Lipase-B (CAL-B) as biocatalyst. The epoxy ring was cleaved with hot water in the presence of tert-butanol (t-BuOH). Pure threo-9, 10-dihydroxystearic acid (DHSA) from animal fat was recovered by crystallization (51% yield). Subsequently, DHSA was esterified in alpha-limonene using biocatalysts yielding twelve DHSEs (58-90% yield). Differential scanning calorimetry (DSC) analysis of these esters revealed potential latent heats ranging from 136.83 kJ kg−1 to 234.22 kJ kg−1 and melting temperatures from 52.45 ◦C to 76.88 ◦C. Finally, the compounds with enthalpies above 200 kJ kg−1 were subjected to 100 and 1000 thermal cycles. These experiments showed that these products present good thermal reliability., GREA and DBA are certified agents TECNIO in the category of technology developers from the Government of Catalonia. We thanks to Subproductos Cárnicos Echevarria y Asociados S.L (Cervera, Spain) for supplying the non-edible fat. Moreover, the research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement no PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement no 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and Agricultural Biotechnology Research Group (2014 SGR 1296). This work has been partially funded by the Spanish government (CTQ2015-70982-C3-1-R (MINECO/FEDER) and ENE2015-64117-C5-1-R (MINECO/FEDER). Aran Solé would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2015-25741.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

An overview on design methodologies for liquid–solid PCM storage systems

  • Castell, Albert
  • Solé Cutrona, Cristian
Energy storage can facilitate the transition process from the actual energetic model to a model based on renewable energies. A lot of attention has been put in such technology, being the use of phase change materials (PCM) of high interest. However, design methodologies for PCM storage systems are still a limiting factor for its deployment. This paper compiles and structures the most common and promising design methodologies and highlights their usefulness and limitations. These methodologies are classified in six types: (1) empirical correlations and characterizing parameters, (2) dimensional analysis and correlations, (3) effectiveness–NTU, (4) Log Mean Temperature Difference (LMTD), (5) Conduction Transfer Functions (CTF), and (6) numerical models. Dimensionless correlations and effectiveness–NTU are the most common and straight-forward methods as well as the ones that offer more possibilities for general solutions. Empirical correlations and numerical models are problem based and difficult to generalize. On the other hand, the adaptation of LMTD and CTF to PCM systems still requires detailed research., The research leading to these results has received funding from the European Union׳s Seventh Framework Program (FP7/2007–2013) under Grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). This work was partially funded by the Spanish government (ENE2011-28269-C03-01 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Model predictive control strategy applied to different types of building for space heating

  • Gholamibozanjani, Gohar
  • Tarragona Roig, Joan
  • Gracia Cuesta, Alvaro de
  • Fernàndez Camon, César
  • Cabeza, Luisa F.
  • Farid, Mohammed M.
In recent years, the concept of energy-efficient buildings has attracted widespread attention due to growing energy consumption in different types of buildings. The application of thermal energy storage (TES) systems, especially latent heat energy storage (LHES), has become a promising approach to improve thermal efficiency of buildings and hence reduce CO2 emissions. One way to achieve this, could be by implementing a model predictive control (MPC) strategy, using weather and electricity cost predictions. To this end, a heat exchanger unit containing a phase change material (PCM) as a LHES medium, thermally charged by solar energy was incorporated into three versions of a standard building. This paper reports on the use of EnergyPlus software to simulate the heating demand profile of these buildings, with Solving Constraint Integer Programs (SCIP) as the optimization tool. After applying MPC strategy, the energy costs of different building types were evaluated. Furthermore, the effect of prediction horizon and decision time step of MPC strategy, and PCM mass capacity on the performance of the MPC were all investigated in 1 and 7-day simulations. Results showed that by increasing the prediction horizon and PCM mass, more cost saving could be obtained. However, in terms of decision time step, although the study revealed that increasing it led to a higher energy saving, it made the system more sensitive to sharp changes as it failed to provide an accurate reading of the parameters and variables., The study was partially funded by the Spanish Government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors at the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537). GREiA is the certified agent for TECNIO in the category technology developers for the Government of Catalonia. The research leading to these results also received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Control strategies comparison of a ventilated facade with PCM – energy savings, cost reduction and CO2 mitigation

  • Gracia Cuesta, Alvaro de
  • Barzin, Reza
  • Fernàndez Camon, César
  • Farid, Mohammed M.
  • Cabeza, Luisa F.
The use of active thermal energy storage can provide energy savings, cost reduction and CO2 mitigation by reducing energy demand for heating and cooling, allowing the use of peak load shifting strategies and enhancing the introduction of renewable energies in the sector. The high investment cost of these systems makes mandatory an appropriate control in order to maximize the energy benefits during its operation. Within this context artificial intelligence techniques have been successfully used to control active thermal energy storage units. This paper uses an experimentally validated numerical tool to study the effect of different control strategies on the performance of one TES system applied to the building sector, a ventilated facade with PCM which uses free cooling. Three different strategies were designed to control the ventilated facade based on cost savings, energy reduction and CO2 mitigation, under different climatic conditions. Results show robust benefits in the three tested control strategies, achieving average savings in comparison to a manual operation of the system of 4.3%, 7.8%, and 16.7%. Moreover, the paper shows that when the control strategy is focused on optimizing cost, the other two benefits claimed by TES systems (energy and CO2 mitigation) are significantly reduced., The work is partially funded by the Spanish Government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), TIN2015-71799-C2-2-P and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 Research and Innovation Programme under grant agreement No. 657466 (INPATH-TES), and the fund received by the Royal Society of New Zealand. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Comparison of phase change slurries: Physicochemical and thermal properties

  • Giro-Paloma, Jessica
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Šumiga, Boštjan
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Phase change slurries (PCS) consist on a carrier fluid binary system, where water is mostly used as continuous phase and micro-encapsulated phase change materials (MPCM) are used as dispersed phase. PCS are used in Thermal Energy Storage (TES) for building applications, combining the latent heat capacity of the MPCM with the sensible heat capacity of the carrier fluid, and at the same time giving the PCM pumpable properties. In this study, two PCS samples are compared and characterized, the commercial Micronal® DS 5007 X from BASF and a laboratory made PCS28. Thereby, in this paper thermal stability is studied by using thermogravimetrical analysis (TGA) and the main components of the MPCM have been studied using Fourier transformed infrared spectroscopy (FT-IR). Moreover, TGA coupled with FT-IR is used to study deeply the thermal decompositions of the PCS microcapsules and products derived thereof. Finally, differential scanning calorimetry (DSC) is performed to study the melting enthalpy and the melting temperature range of the phase change material (PCM). This paper concludes that both types of PCS have good potential from thermal energy storage purposes such as solar space heating applications., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Measurement of enthalpy curves of phase change materials via DSC and T-History: When are both methods needed to estimate the behaviour of the bulk material in applications?

  • Rathgeber, Christoph
  • Miró, Laia
  • Cabeza, Luisa F.
  • Hiebler, Stefan
Thermal energy storages (TES) based on solid–liquid phase change materials (PCM) use the latent heat of the phase transition from solid to liquid and vice versa. The enthalpy change within application relevant temperature ranges has to be determined via calorimetric measurements providing high accuracy. For the most part, enthalpy curves of PCMs are measured either via differential scanning calorimetry (DSC) or via the T-History method, but rarely with both methods. Combined DSC and T-History measurements allow an improved determination of enthalpy curves of PCM, since intrinsic material properties can be separated from properties of the investigated sample and effects of the applied methods. In order to study when both methods are needed to estimate the behaviour of the bulk material in applications, the enthalpy curves upon heating and upon cooling of nine PCM from different material classes were measured via T-History and DSC in both dynamic and step mode. These are: octacosane, decane-1,10-diol, RT80, methylurea, glutaric acid, magnesium chloride hexahydrate, erythritol, sebacic acid and hydroquinone. The comparison of enthalpy curves in terms of melting temperature, degree of subcooling and enthalpy change within application relevant temperature ranges demonstrates the necessity of combined DSC and T-History measurements for materials with volume dependent behaviour. Melting temperatures agree within the limits of RAL testing regulations and considerably less subcooling is observed for T-History samples. If the PCM under investigation can be characterised reasonably with both methods, enthalpy changes determined via DSC and T-History deviate by less than 5%., The work of ZAE Bayern was part of the project EnFoVerM and supported by the German Federal Ministry of Economics and Technology under the project code 0327851D. The work of the University of Lleida was partially funded by the Spanish government (project ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). The work leading to this invention has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miró would like to thank the Spanish Government for her research fellowship at ZAE Bayern (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

PCM incorporation in a concrete core slab as a thermal storage and supply system: proof of concept

  • Navarro Farré, Lidia
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Álvarez, Servando
  • Cabeza, Luisa F.
Phase change materials (PCM) have been widely implemented in buildings envelope as passive system as well as in storage tanks for active systems. A new promising technology has been designed to act as a hybrid system between the passive and active ones. The main idea is using the internal slab as a thermal energy storage system to cover partially the energetic demand both during heating and cooling periods. This innovative constructive system consists of a prefabricated concrete slab with PCM macroencapsulated in small tubes and inserted in its hollows. A direct cross-flow heat exchange occurs between the air pumped into the slab and the PCM for conditioning purposes. A prototype has been implemented in a two storey house-like cubicle and has been tested under real conditions, where the slab becomes a thermal storage and supply component. The objective is to study the thermal performance of the slab and its components, in a theoretical analysis, as well as the suitability of the system in a Mediterranean continental climate. The concept was proved experimentally and compared to the theoretical results to demonstrate the potential of the technology. However, experimental results remarked the importance of a further investigation under real operating conditions., This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. The work partially funded by the Spanish government (ENE2011-28269-C03-01 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n◦ PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental validation of the exact analytical solution to the steady periodic heat transfer problem in a PCM layer

  • Mazzeo, Domenico
  • Oliveti, Giuseppe
  • Gracia, Álvaro de
  • Coma Arpón, Julià
  • Solé, Aran
  • Cabeza, Luisa F.
Phase change materials (PCM) are used in many industrial and residential applications for their advantageous characteristic of high capacity of latent thermal storage by means of an isothermal process. In this context, it is very useful to have predictive mathematical models for the analysis of the thermal performance and for the thermal design of these layers. In this work, an experimental validation of an analytical model that resolves the steady periodic heat transfer problem in a finite layer of PCM is presented. The experimental investigation was conducted employing a PCM with thermophysical and thermochemical behavior very close to those hypothesized in the formulation of the analytical model. For the evaluation of the thermophysical properties of the PCM sample used, an experimental procedure created by the authors was employed. In all tests realized in a sinusoidal and non-sinusoidal periodic regime, the comparison between the measured and calculated trends of the temperature at different sample heights and of the surface heat fluxes show an excellent agreement. Moreover, also having verified the analytical total stored energy, the analytical model constitutes a valid instrument for the evaluation of the latent and sensible contribution and the trend in time of the position of the bi-phase interface., The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union's Horizon 2020 research and innovation programme under grant agreement Nº 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Julià Coma would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2016FI_B2 00147). Aran Solé would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2015-25741.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermomechanical testing under operating conditions of A516Gr70 used for CSP storage tanks

  • Prieto, Cristina
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Thermal energy storage (TES) in molten salts is the storage dominating technology in solar power applications today. In two-tank molten salt storage systems energy density ranges from 30 to 70 kW h/m3 are achievable. The salt material used is a binary system, composed of 60% NaNO3 and 40% KNO3. In the 8 MWhth pilot plant built and tested by Abengoa, the storage tanks were made of steel A516Gr.70 using the Appendix M of code API 650 for their design. A specific testing device was developed to evaluate thermo-mechanical properties, and a study was conducted in order to evaluate tensile properties of A516Gr.70 specimens under operation conditions for the hot tank at the pilot plant that is in contact with molten salts at 380 °C. Results confirmed the outcomes of the work: the reduction of the yield limit, elongation before fracture, and Young modulus at 380 °C after having been 5 min immersed in molten salts. Moreover, after a creep-test simulating operating 7 days conditions during, an additional reduction of the yield limit was measured., The research leading to these results has received funding from Spanish government (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005). The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722, ENE2015-64117-C5-1-R, and ENE2015-64117-C5-2-R). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). Dr. Camila Barreneche would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Acoustic insulation capacity of Vertical Greenery Systems for buildings

  • Pérez Luque, Gabriel
  • Coma Arpón, Julià
  • Barreneche Güerisoli, Camila
  • Gracia Cuesta, Alvaro de
  • Urrestarazu, Miguel
  • Burés, Silvia
  • Cabeza, Luisa F.
Vertical Greenery Systems (VGS) are promising contemporary Green Infrastructure which contribute to the provision of several ecosystem services both at building and urban scales. Among others, the building acoustic insulation and the urban noise reduction could be considered. Traditionally vegetation has been used to acoustically insulate urban areas, especially from the traffic noise. Now, with the introduction of vegetation in buildings, through the VGS, it is necessary to provide experimental data on its operation as acoustic insulation tool in the built environment. In this study the acoustic insulation capacity of two VGS was conducted through in situ measurements according to the UNE-EN ISO 140-5 standard. From the results, it was observed that a thin layer of vegetation (20–30 cm) was able to provide an increase in the sound insulation of 1 dB for traffic noise (in both cases, Green Wall and Green Facade), and an insulation increase between 2 dB (Green Wall) and 3 dB (Green Facade) for a pink noise. In addition to the vegetation contribution to sound insulation, the influence of other factors such as the mass factor (thickness, density and composition of the substrate layer) and type of modular unit of cultivation, the impenetrability (sealing joints between modules) and structural insulation (support structure) must be taken into account for further studies., The work was partially funded by the Spanish government (ENE2011-28269-C03-02, and ULLE10-4E-1305), in collaboration with the company Buresinnova S.A (C/ Saragossa, 95 Entsol 3ª, 08006 BARCELONA). Moreover, the research leading to these results has received funding from the Eurpean Commission Seventh Framework Programm (FP/2007–2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123), to the City Hall of Puigverd de Lleida, and to Gestión Medioambiental de Neumáticos S.L. and Flag Soprema S.L.U. companies. Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201. Finally, Julià Coma wants to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Novel geopolymer for use as a sensible storage option in high temperature thermal energy storage systems

  • Jacob, Rhys
  • Trout, Neil
  • Solé, Aran
  • Clarke, Stephen
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Saman, Wasim
  • Bruno, Frank
In the current study a novel geopolymer created from waste materials (namely fly ash and black slag) has been characterised as a potential high temperature thermal energy storage material option. Several geopolymer samples have been fabricated and characterised by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Additionally, the density and heat capacity have been determined. Lastly, the cost of the material and packed bed system was estimated showing that the geopolymer-based systems are potentially 35% cheaper than the traditional 2-tank molten salt systems., This research was performed as part of the Australian Solar Thermal Research Institute (ASTRI), a project supported by the Australian Government, through the Australian Renewable Energy Agency (ARENA). The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Aran Solé would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2015-25741. The authors would also like to acknowldege the Diopma group from the University of Barcelona thanks the funding by the Spanish Government (RTI2018-093849-B-C32), and the Catalan Government for the quality accreditation (2017 SGR 118).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Simulation-based optimization of PCM melting temperature to improve the energy performance in buildings

  • Saffari Tabalvandani, Mohammad
  • Gracia Cuesta, Alvaro de
  • Fernàndez Camon, César
  • Cabeza, Luisa F.
Globally, a considerable amount of energy is consumed by the building sector. The building envelope can highly influence the energy consumption in buildings. In this regard, innovative technologies such as thermal energy storage (TES) can help to boost the energy efficiency and to reduce the CO2 emissions in this sector. The use of phase change materials (PCM), due to its high heat capacity, has been the centre of attention of many researchers. A considerable number of papers have been published on the application of PCM as passive system in building envelopes. Researches have shown that choosing the PCM melting temperature in different climate conditions is a key factor to improve the energy performance in buildings. In the present paper, a simulation-based optimization methodology will be presented by coupling EnergyPlus and GenOpt with an innovative enthalpy-temperature (h-T) function to define the optimum PCM peak melting temperature to enhance the cooling, heating, and the annual total heating and cooling energy performance of a residential building in various climate conditions based on Köppen-Geiger classification. Results show that in a cooling dominant climate the best PCM melting temperature to reduce the annual energy consumption is close to the maximum of 26ºC (melting range of 24ºC-28ºC), whereas in heating dominant climates PCM with lower melting temperature of 20ºC (melting range of 18ºC-22ºC) yields higher annual energy benefits. Moreover, it was found that the proper selection of PCM melting temperature in each climate zone can lead to notable energy savings for cooling energy consumption, heating energy consumption, and total annual energy consumption., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Program (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement No 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Control of a PCM ventilated facade using reinforcement learning techniques

  • Gracia Cuesta, Alvaro de
  • Fernàndez Camon, César
  • Castell, Albert
  • Mateu Piñol, Carles
  • Cabeza, Luisa F.
Artificial intelligence techniques have been successfully applied to control dynamic systems looking for an optimal control. Among those techniques, reinforcement learning has been shown as particularly effective at reducing the dimensionality of some real problems and solving control problems by learning from experience. The use of thermal energy storage active systems in the building sector is identified as suitable option to reduce their energy demand for heating and cooling. However, these systems might be expensive and require appropriate control strategies in order to improve the performance of the building. In this paper a ventilated facade with PCM is controlled using a reinforcement learning algorithm. The ventilated facade uses mechanical ventilation during nighttime to solidify the PCM and releases this cold stored to the inner environment during the peak demand period. It is crucial to decide correctly the schedule of charge and discharge process of the PCM according to the weather and indoor conditions. An experimentally validated numerical model is used to test the performance of the control algorithm under different weather conditions. Important improvements on the energy savings due to the use of control strategies were found and supported by the data under the different tested climatic conditions., The work partially funded by the Spanish government (ENE2011-28269-C03-01, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014-SGR-123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement #PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental testing of cooling internal loads with a radiant wall

  • Romaní Picas, Joaquim
  • Cabeza, Luisa F.
  • Pérez Luque, Gabriel
  • Pisello, Anna Laura
  • Gracia Cuesta, Alvaro de
Thermally activated building systems (TABS) consist of pipes or ducts embedded in the building structure. This is a well-known technology for its capability to reduce energy use for cooling buildings. Additionally, TABS help integrating renewable energies, such as free-cooling with ground heat exchangers (GHE). However, TABS cooling load is sensitive to the internal load, and the use of GHE for free-cooling is limited to low energy buildings. In a previously published research, a radiant wall cubicle without internal gains demonstrated to achieve significant energy savings. However, the current research showed that under domestic and office scheduled internal gains equivalent to 42 W·m-2 the radiant cubicle increased its energy consumption for cooling more than the reference cubicle with air-to-air heat pumps. As a result, the radiant cubicle used around 20% more energy than the reference at air temperature set-point 24 ºC but saved around 20% compared to the reference at 26 ºC. Despite this, the radiant wall could still reduce the cooling cost through peak load shifting even though it showed to consume more energy than a conventional HP., The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. This projects has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union's Horizon 2020 research and innovation programme under grant agreement Nº 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Critical analysis of the T-history method: A fundamental approach

  • Badenhorst, Heinrich
  • Cabeza, Luisa F.
Energy storage is a key challenge to a sustainable energy supply. To design new storage systems accurateand representative thermal property measurements are essential. The T-history method is quick anduncomplicated, however numerous adaptations have been proposed over the years. In this study thesemethods have been classified and critically assessed based on their mathematical formulation and exper-imental configuration. They can be broadly categorized according to one of three assumptions regardingthe heat transfer coefficient for natural convection: it is constant either as a function of time or tem-perature, or it is negligible. This work proves in addition that the heat transfer coefficient for naturalconvection, varies both as a function of time and temperature. This is demonstrated both experimentallyand through rigorous simulation of the proposed configurations. Thus T-history methods which show themost promise for precise and unambiguous measurements eliminate convection by making conductionthe dominant thermal resistance in the system. These techniques can be tailored to different materialsand do not require a simultaneous reference due to the use of a rigorous fundamental model comparedto the lumped parameter approximation. The addition of heat flux sensors to quantify actual heat lossesis recommended for absolute measurement certainty., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) and under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE), and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). Dr. Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Corrosion of metal containers for use in PCM energy storage

  • Ferrer, Gerard
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Martorell, Ingrid
  • Cabeza, Luisa F.
In recent years, thermal energy storage (TES) systems using phase change materials (PCM) have been widely studied and developed to be applied as solar energy storage units for residential heating and cooling. These systems performance is based on the latent heat due to PCM phase change, a high energy density that can be stored or released depending on the needs. PCM are normally encapsulated in containers, hence the compatibility of the container material with the PCM has to be considered in order to design a resistant container. Therefore, the main aim of this paper is to study the corrosion effects when putting in contact five selected metals (aluminium, copper, carbon steel, stainless steel 304 and stainless steel 316) with four different PCM (one inorganic mixture, one ester and two fatty acid eutectics) to be used in comfort building applications. Results showed corrosion on aluminium specimens. Hence caution must be taken when selecting it as an inorganic salt container. Despite copper has a corrosion rate range of 6e10 mg/cm2 yr in the two fatty acid formulations tested, it could be used as container. Stainless steel 316 and stainless steel 304 showed great corrosion resistance (0e1 mg/cm2 yr) and its use would totally be recommended with any of the studied PCM., The work is partially funded by the Spanish Government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). Aran Sole would like to thank the Departament d'Universitats, Recerca i Societat de la Informacio de la Generalitat de Catalunya for her research fellowship. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007- 2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE)
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal stress reduction in cool roof membranes using phase change materials (PCM)

  • Saffari Tabalvandani, Mohammad
  • Piselli, Cristina
  • Gracia Cuesta, Alvaro de
  • Pisello, Anna Laura
  • Cotana, Franco
  • Cabeza, Luisa F.
A considerable amount of energy is used in the building sector for air conditioning purposes. Additionally, the building sector contributes to the urban heat island (UHI) phenomenon which causes temperature rise in urban areas. Cool roof is an emerging passive cooling technology that can contribute to reduce the cooling energy use in buildings and to mitigate the UHI effects in the urban area. Cool roofs and reflective coatings, despite of being effective in terms of reducing the cooling thermal loads in buildings and decrease the UHI, can suffer from extreme thermal stress which negatively influences their lifespan and performance. Thermal energy storage (TES) is a promising technology which can be applied together with cool roof technology to decrease the extreme thermal stress due to solar radiation as well as providing thermal inertia to the building. In this study, simulation-based optimization will be used to optimize the PCM melting temperature when integrated into a polyurethane-based cool roof membrane to reduce the thermal stress of the cool roof and also to improve the annual energy performance of the building. The optimization results showed that the application of PCM and cool roof technologies together can reduce the severe thermal stress of the cool roof membrane when the optimization objective is the annual thermal stress of the cool roof. On the other hand, when PCM melting temperature is optimized to reduce the annual energy needs, higher annual energy savings could be achieved with acceptable reductions in the cool roof membrane thermal stress., The research leading to these results has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Program (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. A.L. Pisello’s acknowledgments are due to the UNESCO Chair “Water Resources Management and Culture”, for supporting her research.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Health hazard, cycling and thermal stability as key parameters when selecting a suitable phase change material (PCM)

  • Miró, Laia
  • Barreneche Güerisoli, Camila
  • Ferrer, Gerard
  • Solé, Aran
  • Martorell, Ingrid
  • Cabeza, Luisa F.
From the literature review it was observed that there is no established methodology, neither a common pattern, when selecting a phase change material for a thermal energy storage application. Melting temperature and enthalpy have traditionally been the considered thermal properties for the material selection. Therefore, the authors of this paper propose a new method of investigation on the suitability of a PCM that takes into account not only thermal properties but also health hazard and both cycling and thermal stability. Health hazard is related with the handling of the material, and both cycling and thermal stabilities with durability. This methodology is applied to five different PCM in the 150–200 °C range: salicylic acid, benzanilide, d-mannitol, hydroquinone, and potassium thiocyanate. Results show that for an application in the 150–200 °C range the suitable PCM are benzanilide and d-mannitol. Moreover, hydroquinone is also suitable but only in closed systems., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The work is partially funded by the Spanish government (ENE2011-22722). The authors would also like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). Aran Solé would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for her research fellowship. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Use of partial load operating conditions for latent thermal energy storage management

  • Gasia, Jaume
  • Gracia Cuesta, Alvaro de
  • Peiró Bell-lloch, Gerard
  • Arena, Simone
  • Cau, Giorgio
  • Cabeza, Luisa F.
A proper management of thermal energy storage (TES) charging and discharging processes allows the final users to optimize the performance of TES systems. In this paper, an experimental research is carried out to study how the percentage of charge in a latent heat TES system (partial load operating conditions) influences the discharge process. Several charging and discharging processes were performed at a constant heat transfer fluid (HTF) mass flow rate of 0.5 kg/s and temperature of 155 °C and 105 °C, respectively. High density polyethylene (HDPE) with a total mass of 99.5 kg was used as phase change material (PCM) in a 0.154m3 storage tank based on the shelland-tube heat exchanger concept. Five different percentages of charge have been studied: 58 %, 73 %, 83 %, 92 %, and 97 % (baseline test). Results showed that by modifying the percentage of charge, the time required for the charging process was reduced between 97.2% and 68.8% in comparison to the baseline case. However, the energy accumulated was only reduced a maximum of 35.1% and a minimum of 5.2%, while the heat transfer rates during the first 60 min of discharge were reduced a maximum of 45.8% and a minimum of 6%. Therefore, partially charging the TES system not lower than 85% of its maximum energy capacity becomes a good option if the final application accepts a maximum decrease of discharging heat transfer rates of 10% if compared to the fully charged system., The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017 FI_B1 00092). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Simone Arena would like to thank the Department of Mechanical, Chemical and Materials Engineering of the University of Cagliari for funding his research grant.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal characterization of different substrates under dried conditions for extensive green roofs

  • Coma Arpón, Julià
  • Gracia Cuesta, Alvaro de
  • Chàfer, Marta
  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
Extensive green roofs have been consolidated as good tools for passive energy saving systems in buildings,providing a more sustainable trend in the building field. However, as the growth of vegetation is variable depending on external factors such as weather conditions, disease, etc. the coverage of plants cannot ensure uniformity and consequently the 'shadow effect' cannot be considered as a constant parameter.On the other hand, materials used in substrate and drainage layers should provide a constant 'insulation effect' depending only on their physical properties and water content. In spite of this, the complexity of disaggregated materials used in internal layers of extensive green roofs implies a lack of real data about their thermal properties. The main objective of this study is to determine experimentally the physical properties of different disaggregated materials from the internal layers of extensive green roofs commonly used in Mediterranean climates. The experimentation presented in this paper allows to calculate the thermal transmittance in steady-state (U-value), the heat storage capacity (Cp), and the dynamic thermal response under a daily thermal oscillation., This work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ULLE10-4E-1305), in collaboration with the company Buresinnova S.A (C/Roc Boronat 117-125, baixos 08018 Barcelona). Moreover, the research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union’s Horizon 2020 research and innovation programme under grant agreement N° 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Finally, Julià Coma wants to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de;1; Catalunya for his research fellowship.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Review of technology: Thermochemical energy storage for concentrated solar power plants

  • Prieto, Cristina
  • Cooper, Patrick
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
To be able to extend the operation of a solar power plant (CSP) up to 15 h, thermal energy storage (TES) is necessary. But TES also provides more versatility to the plant and makes its reliance during operation hours more dependable. On the other hand, due to the different CSP configurations, a broad spectrum of storage technologies, materials and methods is needed. Sensible and latent heat storage are known technologies in CSP, but thermochemical storage (TCS) is still very much at laboratory level. Nevertheless, TCS has de advantage of nearly no losses during storage and very good volumetric energy density. This review summarizes and compares the different TCS that are today being investigated. Those systems are based in three redox reactions, sulfur-based cycles, metal oxide reduction–oxidation cycles, and perovskite-type hydrogen production, and metal oxide non-redox cycles due to their similarity. This review shows that all these cycles are promising, but none of them seems to have all the characteristics necessary to become the only one storage system for CSP. The main conclusion of the review is that the calcium carbonate is the cycle with most experimentation behind it to infer that it could be viable and should thus be attempted at a research plant scale once a reactivation cycle can be designed; and the manganese oxide cycle, while less developed, is fundamental enough to be a suitable application for desert climates over the rest of the water-frugal or even water-avoiding cycles., The work was partially funded by the Spanish government (project ENE2011−22722). The authors would also like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union׳s Seventh Framework Programme (FP7/2007−2013) under Grant agreement n° PIRSES-GA−2013−610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal energy storage evaluation in direct steam generation solar plants

  • Prieto, Cristina
  • Rodríguez-Sánchez, Alfonso
  • Patiño-Rodríguez, David
  • Cabeza, Luisa F.
Existing commercial parabolic trough power plants use thermal oil as a heat transfer fluid, with working temperatures in the region of 400 °C. In order to achieve more efficient generating systems, a second generation of parabolic troughs that operate at temperatures higher than 400 °C is being developed. One possibility Abengoa Solar is assessing is the use of direct steam generation (DSG) inside parabolic troughs in order to achieve higher temperatures; in a first stage heating up to 450 °C and in a second stage heating up to 550 °C. For the future market potential of parabolic trough power plants with DSG, it is beneficial to integrate thermal energy storage (TES) systems. Different TES options based on the most known technologies, steam accumulators, molten salts (MS), and phase change materials (PCM), are presented and compared in this paper. This comparison shows as main conclusion of the study that a combined system based on PCM-MS has a clear advantage in the ratio with 6 or more equivalent hours of storage, while with lower than 6 h, steam accumulators are considered the best option., The work partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). Prof. Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Simulation and control of thermally activated building systems (TABS)

  • Romaní Picas, Joaquim
  • Gracia Cuesta, Alvaro de
  • Cabeza, Luisa F.
Buildings account for a significant amount of global energy use and CO2 emissions. Thermally Activated Building Systems (TABS) are a technology with potential for significantly reducing buildings energy use. TABS are heating and cooling systems that are integrated in the building structure. They mainly exchange heat through radiation and are able to store heat in the building thermal mass. TABS high thermal mass and their interaction with the building structure make their energy evaluation and design process difficult. Development of simulation models has been essential to study the design and control of TABS. Control of TABS is challenging due to the slow response time and storage capacity. A lot of research has been conducted to develop control strategies that fully exploit its energy saving potential and that maximize the use of renewable energies. This paper summarizes the main characteristics of TABS and presents the developed simulation models and control strategies., The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). This projects has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N° PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union’s Horizon 2020 research and innovation programme under grant agreement N° 657466 (INPATH-TES) and from EEA-Grants under grant IDI-20140914. The work was partially funded by the Spanish government grant ENE2015-64117-C5-1-R and grant ENE2015-64117-C5-3-R. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Fatty acid eutectic mixtures and derivatives from non-edible animal fat as phase change materials

  • Gallart-Sirvent, Pau
  • Martín, Marc
  • Villorbina Noguera, Gemma
  • Balcells Fluvià, Mercè
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Cabeza, Luisa F.
  • Canela i Garayoa, Ramon
A set of compounds from non-edible fat waste was prepared and their thermal behavior was studied. The fat was hydrolyzed and crystallized in a simple and robust process to yield palmitic acid-stearic acid (PA-SA) mixtures. The PA-SA mass ratios determined by GC-FID (gas chromatography-flame ionization detection) were similar to those reported for eutectic mixtures of PCMs (phase change materials). DSC (differential scanning calorimetry) results indicated that the melting and solidification temperatures were around 55 °C and 52 °C and the latent heat of the crystallized fractions measured was around 180 kJ kg−1. The thermal cycling reliability of the eutectic mixtures was also tested during 1000 melting/freezing cycles. The loss in melting and solidification enthalpies was below 14% in all mixtures showing a promising behavior for PCM applications. Additionally, the unsaturated fatty acids were recovered and transformed to threo-9,10-dihydroxystearic acid (DHSA) and some of their inorganic salts, which were analyzed by FT-IR (Fourier transform-infrared spectroscopy) and tested for the first time using the DSC technique., GREA and DBA are certified agents TECNIO in the category of technology developers from the Government of Catalonia. We thanks to Subproductos Cárnicos Echevarria y Asociados S.L (Cervera, Spain) for supplying the non-edible fat. Moreover, the research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation program under grant agreement no. 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123), Agricultural Biotechnology Research Group (2014 SGR 1296) and DIOPMA (2014 SGR 1543). This work has been partially funded by the Spanish government (CTQ2015-70982-C3-1-R (MINECO/FEDER), ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). Dr Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for her grant Juan de la Cierva FJCI-2014-22886. Aran Solé would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2015-25741.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

An effectiveness-NTU technique for characterising a finned tubes PCM system using a CFD model

  • Tay, N. H. Steven
  • Belusko, Martin
  • Castell, Albert
  • Cabeza, Luisa F.
  • Bruno, Frank
Numerical modelling is commonly used to design, analyse and optimise tube-in-tank phase change thermal energy storage systems with fins. A new simplified two dimensional mathematical model, based on the effectiveness-number of transfer units technique, has been developed to characterise tube-in-tank phase change material systems, with radial round fins. The model applies an empirically derived P factor which defines the proportion of the heat flow which is parallel and isothermal. This P factor was determined using a validated computational fluid dynamics model. This method can be used to design and optimise tube-in-tank salt based phase change thermal storage units with finned tubes., The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007- 2013) under Grant Agreement No PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Single layer mortars with microencapsulated PCM: Study of physical and thermal properties, and fire behaviour

  • Haurie, Laia
  • Serrano, Susana
  • Bosch González, Montse
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Phase change materials are a promising strategy to reduce energy consumption in a wide range of applications including the building sector. Many studies have been done to evaluate the impact of PCM on thermal properties of building materials, however there exists little information on the influence of PCM on other properties of the support materials. This knowledge is necessary to determine the feasibility to apply and use building materials containing PCM. In this paper, the effect of the addition of different percentages of microencapsulated phase change material on the properties of two commercial single layer mortars has been studied. Physical and thermal properties as well as fire reaction have been evaluated., The work is partially funded by the Spanish Government(ENE2011-28269-C03-02 and MAT2011-26410). The authorswould like to thank the Catalan Government for the quality accredi-tation given to their research group GREA (2014 SGR 123), researchgroup DIOPMA (2014 SGR 1543) and research group GICITED (2014SGR 1298).The work leading to this invention has received fundingfrom the European Union’s Seventh Framework Programme(FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE)
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Benchmarking of energy demand of domestic and small business buildings

  • Coma Arpón, Julià
  • Maldonado, José Miguel
  • Gracia Cuesta, Alvaro de
  • Gimbernat, Toni
  • Botargues, Teresa
  • Cabeza, Luisa F.
Rapid expansion of solar thermal energy for increasing energy efficiency of buildings has been adopted in short/medium and long-term energy strategies of EU countries. This enhancement of energy efficiency in buildings is in line with regional actions with the European climate energy objectives as defined in the European Union’s “20-20-20” targets and in the European Commission’s Energy Roadmap 2050. Within this context, the overall objective of this work is to develop an innovative high performance and cost effective hybrid solar heat and power system, which consist in a novel flat Fresnel mirror solar concentrating collector and micro organic Rankine cycle plant combined with advanced phase change materials as thermal storage, all system managed by smart control units. The initial application is to be implemented in individual dwellings and small business residential buildings for on-site electricity and heat generation using solar thermal energy. It is estimated that the proposed technology will deliver 60% of domestic energy requirements and provide 20% reduction in energy costs and greenhouse gas emissions compared to the best existing low carbon energy technologies. To reach the main objectives, the first step consist in providing information on features of architecture of domestic and small business residential buildings and their annual energy demands for different countries such as: Spain, France Germany, Italy, and United Kingdom. This will include detailed building information of envelopes (walls, roof, lofts, etc.), structure, fabric, and results of energy demands (domestic hot water, space heating and electricity) for the abovementioned countries. This information will be used as input data during the development of this technology as it will point out the potential benefits of the system in different countries, climates, and building typologies., This study has received funding from European Union’s Horizon 2020 research and innovation programme under grant agreement Nº723596 (Innova MicroSolar) and Nº 657466 (INPATH-TES), from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE). The work is partially funded by the Spanish government ENE2015- 64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER) and (ULLE10-4E-1305). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental evaluation of a cooling radiant wall coupled to a ground heat exchanger

  • Romaní Picas, Joaquim
  • Pérez Luque, Gabriel
  • Gracia Cuesta, Alvaro de
A building prototype was built in the experimental set-up located in Puigverd de Lleida (Spain) to study the energy performance of a radiant wall with ventilated facade cooled with a ground coupled heat-exchanger. The installed geothermal heat pump operates only as a ground coupled heat exchanger on cooling mode, thus providing free-cooling. In this case, only the circulation pumps consume power. The summer experimental campaign showed the energy savings potential and the peak load shifting ability of the system. On continuous operation and taking as reference a cubicle equipped with a conventional air-to-air heat pump, the radiant wall cooled with the ground coupled heat-exchanger achieved savings up to 54.17% and 82.08% at set-point temperatures of 24 °C and 26 °C, respectively. The thermal storage capacity of the system was studied in night charging test, when the cubicles were pre-cooled during night-time. During the day, the temperature raise caused by heat loads was small and the system kept the temperature inside comfort range despite it only operated overnight. However, the performance was very sensitive to set-point temperature. Free-cooling was limited by the temperatures in the boreholes, showing that with lower set-points the gradient between supply temperature and room temperature was small, and thus it required a higher water flow to achieve the necessary cooling power. Intermittent operation of the system according to different schedules also affected the radiant walls performance as they interacted with the thermal inertia of the system, which could even have a negative impact on energy use., The work partially funded by the Spanish government (ULLE10-4E-1305, ENE2015-64117-C5-1-R(MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. This projects has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES) and from EEA-Grants under grant IDI-20140914. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Enthalpy-temperature plots to compare calorimetric measurements of phase change materials at different sample scales

  • Rathgeber, Christoph
  • Schmit, Henri
  • Miró, Laia
  • Cabeza, Luisa F.
  • Gutiérrez, Andrea
  • Ushak, Svetlana
  • Hiebler, Stefan
Phase change materials (PCM) can provide high thermal energy storage capacities in narrow temperature ranges around their phase change temperature. The expectable maximum storage capacity of a PCM in a defined temperature range is equal to the enthalpy change in that range and can be determined via calorimetric measurements such as differential scanning calorimetry (DSC) or T-History calorimetry. T-History samples (aprox. 15 ml) are about 1000 times larger than DSC samples (aprox. 15 ml). Experiments in a pilot plant are performed to study the charging and discharging behaviour of even larger amounts of the PCM (aprox. 150 l). The common practise is to investigate PCM at one scale, rarely at two scales. In this work, the characterisation was carried out at three scales (DSC, T-History, and pilot plant) for four PCM (RT58, bischofite, D-mannitol, and hydroquinone). Thereby, the question arises how the enthalpy changes measured at different scales and under different conditions can be compared. In literature, the melting enthalpy is usually assigned to a single temperature without indicating the temperature range considered for evaluation. In very few instances, the enthalpy change within a defined temperature range is stated. In both cases, results measured under different conditions are difficult to compare. In this work, it is demonstrated that enthalpy-temperature plots facilitate the comparison and interpretation of measurements obtained under different experimental methods at different sample scales., The work of ZAE Bayern was part of the project EnFoVerM and was supported by the German Federal Ministry for Economic Affairs and Energy under the project code 0327851D. The work at the University of Lleida is partially funded by the Spanish government (ENE2011-22722, ENE2015-64117-C5-1-R (MINECO/FEDER) and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The authors want also to thank the collaboration of Antoni Gil from Massachusetts Institute of Technology (USA), Eduard Oró from Catalonia Institute for Energy Research (Spain), and Jaume Gasia and Gerard Peiró from University of Lleida (Spain). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The work of the University of Antofagasta was supported by FONDAP SERC-Chile (grant N° 15110019), and the Education Ministry of Chile Grant PMI ANT 1201. Authors thank the SALMAG Company for providing of bischofite. Andrea Gutierrez would like to acknowledge to the Ministry of Education of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI N° 7813110010.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Energy performance of a ventilated double skin facade with PCM under different climates

  • Gracia Cuesta, Alvaro de
  • Navarro Farré, Lidia
  • Castell, Albert
  • Cabeza, Luisa F.
New policies are being promoted worldwide to reduce the energy consumption for space heating and cooling in the building sector. As a new technology to achieve this objective, phase change material (PCM) panels were installed in a new type of ventilated facade to reduce the consumption for space heating and cooling. During winter, the PCM increases the heat storage capacity of the system exposed to solar radiation, while during summer the system can be used as a cold storage unit or as a night free cooling device. The potential of the system to provide energy benefits in the heating period has been demonstrated experimentally under Mediterranean—continental climate conditions, on the other hand, limited benefits were found during the cooling season. The aim of this study is to determine the potential and suitability of this system to operate for cooling purposes, under different weather conditions around the world. In order to accomplish this objective, an own developed numerical model, based on finite control volume approach, was developed and validated against experimental data. The numerical tool is also used to improve the design and to select the most appropriate schedule of the system under the different analysed weather conditions., This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferidade edificios” withthe collaborationof DETEA. The workpartially funded by the Spanish government (ENE2011-28269-C03-01 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no PIRSESGA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

State of the art on gas-solid thermochemical energy storage systems and reactors for building applications

  • Solé, Aran
  • Martorell, Ingrid
  • Cabeza, Luisa F.
Thermal energy storage (TES) is moving towards thermochemical materials (TCM) which present attractive advantages compared to sensible and phase change materials. Nevertheless, TCM are more complex to characterize at lab scale and also the implied technology, which belongs to the chemical engineering field, needs to be contextualized in the TES field. System configurations for thermochemical energy storage are being divided into open/closed storage system and separate/integrated reactor system. Reactors, which are the core of the system, are the focus of this paper. Different gas–solid thermochemical and sorption reactors for building applications are reviewed from lab to pilot plant scale, from 0.015 to 7850 dm3. Fixed bed reactors are the most used ones. Mainly, mass transfer is limiting to achieve the expected energy density. The geometry of the reactor and contact flow pattern between phases are key parameters for a better performance., Aran Solé would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for her research fellowship. The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123). The work is partially funded by the Spanish government(ENE2011-22722). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Comparative study of the thermal performance of four different shell-and-tube heat exchangers used as latent heat thermal energy storage systems

  • Gasia, Jaume
  • Diriken, Jan
  • Bourke, Malcolm
  • Van Bael, Johan
  • Cabeza, Luisa F.
In this paper, the influence of the addition of fins and the use of two different heat transfer fluids (water and a commercial silicone) have been experimentally tested and compared in four latent heat thermal energy storage systems, based on the shell-and-tube heat exchanger concept, using paraffin RT58 as phase change material. Three European institutions were involved under the framework of the MERITS project. A common approach (temperature and power profiles), and five different key performance indicators have been defined and used for the comparison: energy charged, average power, 5-min peak power, peak power to energy ratio, and time. For the same heat transfer fluid, results showed that finned designs (4.7-9.4 times more heat transfer surface) showed an improvement of up to 40%. On the contrary, for the same design, water (which has a specific heat 3 times higher and a thermal conductivity 4.9 times higher than silicone Syltherm 800), yielded results up to 44% higher., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under grant agreement No ENER/FP7/295983 (MERITS) and under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE), and from the European Union's Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B 00092).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Computational efficiency in numerical modeling of high temperature latent heat storage: comparison of selected software tools based on experimental data

  • Pointner, Harald
  • Gracia Cuesta, Alvaro de
  • Vogel, Julian
  • Tay, N. H. Steven
  • Liu, Ming
  • Johnson, Maike
  • Cabeza, Luisa F.
In this article, four different numerical models for the investigation of phase change processes within latent heat storage are described and compared concerning accuracy, convergence behavior and computational efficiency. The models are based on different types of discretization, make use of different ways to model phase change and are implemented with C, MATLAB or ANSYS CFX. After a brief introduction into each investigated numerical model, the experimental reference setup is described. It consists of a flat plate latent heat storage with the eutectic mixture NaNO3 (46 wt%)–KNO3 (54 wt%) with a measured melting temperature of 219.5 °C as storage material. Based on the corresponding simulation model developed in this paper, the comparison of the numerical models is achieved. This methodology allows the investigation of the numerical performance of different software tools in the context of high temperature latent heat storage that was not achieved thus far. All four numerical models show good agreement to experimental results but differ significantly in speed and convergence behavior., This work was partially funded by the nextPCM project supported by the German Federal Ministry for the Environment, Nature Conservation and Nuclear Safety. Moreover, the work was partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305). The authors Alvaro de Gracia and Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to their research group (2014-SGR-123). The research leading to parts of these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank the Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermophysical characterization and thermal cycling stability of two TCM: CaCl2 and zeolite

  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
  • Cuypers, Ruud
At this moment, the global energy consumption in buildings is around 40% of the total energy consumption in developed countries. Thermal energy storage (TES) is presented as one way to address this energyrelated problem proposing an alternative to reduce the gap between energy supply and energy demand. One way to store energy is using thermochemical materials (TCM). These types of materials allow accumulating energy through a chemical process at low temperature, almost without heat losses. In addition, it is a stable way to perform the heat storage and TCM can be implemented for seasonal storage or/and long term storage. This study compares the cyclability, from the thermophysical point of view, CaCl2 which follows a chemical reaction and zeolite which follows a sorption process to be used as TCM for seasonal/long term storage. The main results show that the chemical reaction TCM is more energy-efficient than the sorption TCM. The CaCl2 calculated energy density is 1.47 GJ/m3 , being the best option to be considered to be used as TCM, even though the dehydration process of the zeolite is simpler and it occurs at higher temperatures its calculated energy density is only 0.2 GJ/m3 ., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/ 2007-2013) under grant agreement No ENER/FP7/1295983 (MERITS) and under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Furthermore, the work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011- 22722), and the European Union by Cost Action TU0802. The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Numerical simulation of a PCM packed bed system: A review

  • Gracia Cuesta, Alvaro de
  • Cabeza, Luisa F.
The detailed study of latent packed bed thermal energy storage (TES) system has been a great topic of interest in the literature. Experimental measurements have been conducted to analyze the performance of these systems, however, the complex transient nature of latent TES makes necessary the use of numerical models for detailed study and evaluation of key design parameters, which lead to a numerous scientific contributions in the field. Different and diverse numerical models have been developed, which can be mainly divided into single phase models, Schumman's model, concentric dispersion model, and continuous solid phase model. This paper provides an extensive comprehensive revision of the different numerical models, highlighting the key aspects of each one as well as the main findings in the field. Furthermore, the performance of the different methodologies are discussed and compared. The most important empirical correlations used in the different models in order to take into account physics, such as natural convection inside the spheres or effective thermal conductivity of heat transfer fluid, are also given., The work partially funded by the Spanish Government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under Grant agreement no. 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Characterization of granular phase change materials for thermal energy storage applications in fluidized beds

  • Izquierdo Barrientos, M. A.
  • Sobrino, C.
  • Almendros Ibáñez, J. A.
  • Barreneche Güerisoli, Camila
  • Ellis, N.
  • Cabeza, Luisa F.
This work investigates commercially available granular phase change materials (PCMs) with different transition temperatures for the use of thermal-energy storage systems in fluidized beds. The hydrodynamic characteristics of granular PCMs were tested in cylindrical-3D and planar-2D fluidized beds. The density, particle size distribution and angle of repose were measured for various PCM materials. Further attrition studies were conducted with changes in particle surface from abrasion, which were characterized using a Scanning Electron Microscope (SEM). The results indicate that some materials with smaller particle size and thinner supporting structure can lose the paraffin during the fluidization process, when paraffin is in a liquid state. As a consequence, the particles agglomerate, and the bed defluidizes. For all of the tested materials, only GR50 (with a transition temperature of 50 °C) properly fluidizes when the paraffin is in the liquid state and has shown to endure >75 h of continuous operation and 15 melting-solidification cycles in a fluidized bed. Additional differential scanning calorimetry (DSC) measurements of the cycled particles did not show a decrease in energy storage capacity of the granular PCM, which corroborates that there is no loss of material after >75 h of fluidization., The work is partially funded by the Spanish government (ENE2010-15403, ENE2011-22722 and ENE2015-64117-C5-1). The authors would like to thank the Catalan Government for the quality accreditation to their research groups GREA (2014 SGR 123). The study that led to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n°n°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

New proposed methodology for specific heat capacity determination of materials for thermal energy storage (TES) by DSC

  • Ferrer, Gerard
  • Barreneche Güerisoli, Camila
  • Solé, Aran
  • Martorell, Ingrid
  • Cabeza, Luisa F.
This study presents a methodology to determine the specific heat capacity (Cp) of materials for thermal energy storage (TES) by DSC. These materials have great energy storage capacities, and due to that, important heat flow fluctuations can be observed for each temperature differential, taking more time to reach a desired temperature gradient. Three different DSC methods are considered to be applied in the methodology, and are explained and compared in this study in order to select the most proper one for Cp determination. To perform this study, the Cp of three materials commonly used in sensible TES systems, slate, water, and potassium nitrate (KNO3), is determined. Excellent results with errors lower than 3% are obtained when using the proposed methodology with the areas method. Worse results are obtained with both dynamic and isostep methods, with errors up to 6% and 16% respectively, as a consequence of sensitivity problems during the measurements., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Control concepts of a radiant wall working as thermal energy storage for peak load shifting of a heat pump coupled to a PV array

  • Romaní Picas, Joaquim
  • Belusko, Martin
  • Alemu, Alemu
  • Cabeza, Luisa F.
  • Gracia Cuesta, Alvaro de
  • Bruno, Frank
Photovoltaic panels (PV) coupled to a heat pump supplying heat to a radiant wall is a system with potential to reduce the imported energy from the grid for heating and cooling of buildings. The radiant wall works as a thermal storage system (TES) allowing storage of the PV output and, thus, peak load shifting. However, the management of these technologies is complex due to the dynamics of the system. This paper presents several control concepts with different purposes such as shifting energy use to off-peak periods, maximizing self-consumption of PV output, and minimization of imported energy from the grid. An experimentally validated numerical model from previous research was used to investigate and compare the different proposed control concepts. Results showed that charging the wall with solar energy resulted in higher overall energy use of the heat pump, while the imported grid energy was significantly reduced, thanks to self-consumption., The authors acknowledge the South Australian Department of State Development who have funded this research through the Premier's Research Industry Fund - International Research Grant Program (IRGP 33). The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. This projects has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union's Horizon 2020 research and innovation programme under grant agreement Nº 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Influence of nanoparticle morphology and its dispersion ability regarding thermal properties of water used as phase change materials

  • Barreneche Güerisoli, Camila
  • Mondragon, Rosa
  • Ventura Espinosa, David D
  • Mata, José
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
  • Julia, J. Enrique
Nanoparticles with different morphologies were added to water to study if the morphology of the nanoparticles affects the main parameters of water used as phase change material (PCM). Considered morphologies were spherical, tubes and sheets in the form of spherical carbon black nanoparticles (CB), multiwalled carbon nanotubes (MWCNT), and graphene oxide nanosheets (GO). Results demonstrate that effectively the morphology of nanoparticles affect the thermophysical properties of the nano-enhanced PCM (NePCM). Depending on the morphology of the added nanoparticle, the final NePCM will have different subcooling and thermal conductivity, whereas its phase change enthalpy is not affected and, therefore, is the same for all produced NePCM., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123), DIOPMA (2014 SGR 1543). This work has been partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva FJCI-2014-22886. This work has been developed by participants of the COST Action CA15119 Overcoming Barriers to Nanofluids Market Uptake (NANOUPTAKE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Reduction of the subcooling of bischofite with the use of nucleatings agents

  • Ushak, Svetlana
  • Gutiérrez, Andrea
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Grágeda, Mario
  • Cabeza, Luisa F.
The use of by-products or wastes as phase change materials (PCM) in thermal energy storage (TES) systems is a good option to decrease the cost of such systems. One of the main disadvantages of PCM if inorganic materials are used is subcooling, as was found with bischofite, a by-product from the Chilean non-metallic industry, which subcooling is about 36 °C. Subcooling can be reduced by the addition of nucleating agents, but the selection of the best nucleating agent should be done taking into consideration the physical and chemical parameters of the salt hydrate. In this paper the parameters considered were the solubility of the materials in water, the chemical structure and the crystalline structure (crystal system, lattice parameters, density, cell volume, Z, and space group). It could be concluded that solubility, chemical structure and the crystal system have no influence in the nucleation capacity of a salt hydrate. The parameter that needs to be considered when selecting a nucleating agent for a salt hydrate is the lattice parameters of the crystal structure (cell longitude or angle)., The work at the University of Antofagasta was supported by CONICYT/FONDAP No. 15110019, and the Education Ministry of Chile Grant PMI ANT 1201. Andrea Gutierrez would like to acknowledge to the CONICYT/PAI No 7813110010 and Education Ministry of Chile her postdoctorate scholarships ANT 1106. The work is partially funded by the Spanish Government (ENE2015-64117-C5-1-R and ENE2015-64117-C5-2-R). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). This project has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for the grant Juan de la Cierva, FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Key performance indicators in thermal energy storage: survey and assessment

  • Cabeza, Luisa F.
  • Galindo, Esther
  • Prieto, Cristina
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
Thermal energy storage (TES) is recognised as a key technology for further deployment of renewable energy and to increase energy efficiency in our systems. Several technology roadmaps include this technology in their portfolio to achieve such objectives. In this paper, a first attempt to collect, organise and classify key performance indicators (KPI) used for TES is presented. Up to now, only KPI for TES in solar power plants (CSP) and in buildings can be found. The listed KPI are quantified in the literature and compared in this paper. This paper shows that TES can only be implemented by policy makers if more KPI are identified for more applications. Moreover, close monitoring of the achievements of the already identified KPI needs to be carried out to demonstrate the potential of TES., The work is partially funded by the Spanish Government (ENE2011-28269-C03-02, ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Types, methods, techniques, and applications for microencapsulated phase change materials (MPCM): a review

  • Giro-Paloma, Jessica
  • Martínez, Mònica
  • Cabeza, Luisa F.
  • Fernández Renna, Ana Inés
Phase change materials (PCM) can be employed in many fields because of their capacity to absorb and release energy when it is necessary. Nowadays, the number of studies about these materials is increasing because of their benefits in energy systems. This paper reviews the previous researches and developments on microencapsulated phase change materials (MPCM) in thermal energy storage (TES) systems, focusing on the different methods of encapsulations and also the different applications of these materials. This review aims to be a useful guide for the researchers in this area, because it explains the different types of phase change core materials, the different shells, the methods to microencapsulate these PCM, the most used techniques to characterize these microencapsulated phase change materials, and a revision of the main applications., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007–2013) under Grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Renewable energy research and technologies through responsible research and innovation looking glass: reflexions, theoretical approaches and contemporary discourses

  • Carbajo Garcia, Ruth
  • Cabeza, Luisa F.
The increasing challenges that energy research faces as a priority in most of the global research agendas, are revealed both in terms of social and technical issues. Energy research highlights are set on the development of reliable renewable energy systems and applications; transition to decentralized systems and socio-technical, behavioural and institutional issues combination which requires the integration of both energy and research policies. Global trends in research policies showing an advocacy for responsible approaches are for example Responsible Research and Innovation (RRI) and Open Innovation European strategies which promote the development of social issues as core key of the research and innovation and the definition of the outcomes as the expression of human values such as safety, justice, sustainability and efficiency. The purpose of this article is to present a reflexion regarding to a contextualization of this approach in energy research. Therefore, a range of theoretical backgrounds, meaning making processes, historical approaches, frameworks and contemporary discourses, have been examined. Our aim is to provide a detailed review of existing literature related to the key elements of Responsible Research and Innovation. The innovative contribution is focused in the vision of these key elements applied to energy research, with particular reference to renewables and the outline of the many factors influencing the real field implementation. Results show the existence of a common ground between responsible approaches and many concepts from energy research and social sciences frames. Responsibility as understood in the RRI framework was found not deliberately represented, although, shifts towards responsible approach in social dimension treatment of renewable energy research appeared notable., The work presented was partially funded by the Spanish government ( ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors of this paper would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Vertical Greenery Systems (VGS) for energy saving in buildings: A review

  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
  • Coma Arpón, Julià
  • Martorell, Ingrid
This review paper organizes and summarizes the literature on Vertical Greenery Systems (VGS) when used as passive tool for energy savings in buildings. First, with the information obtained in the reviewed literature some key aspects to consider when working with VGS are clarified, such as the classification systems, the climate influence, the plant species used and the different operating mechanisms. Then, the main conclusions of this literature, sorted by construction system (Green Walls or Green Façades) and climatic situation, are summarized. In general, it can be concluded that VGS provide great potential in reducing energy consumption in buildings, especially in the cooling periods. However, a lack of data on operation during the heating period as well as during the whole year has been found. On the other hand, results show that the investigations of VGS are not equally distributed around the world, being basically concentrated in Europe and Asia. Moreover, the review concludes that some aspects must be studied in depth, such as which species are the most suitable for each climate, influence on energy savings of the façade orientation, foliage thickness, presence of air layers, and finally, substrate layer composition and thickness in the case of green walls., The work was partially funded by the Spanish Government (ENE2011-28269-C03-01 and ENE2011-28269-C03-02) and from the European Union's Seventh Framework Programme(FP7/2007– 2013) under Grant agreement no.PIRSES-GA-2013–610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Study of corrosion by Dynamic Gravimetric Analysis (DGA) methodology. Influence of chloride content in solar salt

  • Prieto, Cristina
  • Gallardo-González, J.
  • Ruiz-Cabañas, F. Javier
  • Barreneche Güerisoli, Camila
  • Martínez, Mònica
  • Segarra Rubí, Mercè
  • Fernández Renna, Ana Inés
When a system for thermal energy storage (TES) is designed, many factors must be considered: storage time, dimensions, material to store heat, etc. Usually, molten salts are selected as TES materials because of their great thermal properties at high temperatures. When the whole TES system is going to be built, the material to be used for containing the thermal storage material becomes an important issue. It must have proper mechanical properties, withstand high temperatures and, above all, resist corrosion due to storage material, being in most of the cases, highly corrosive molten salt mixtures. To determine the corrosion on a metal plate, ASTM Standard-G1-03 procedure is usually applied, in which the corroded metal sample is submitted to several cycles including: attack by a chemical solution, washing, cleaning, drying, and weighing. In order to minimise the handling of the sample, a new methodology (Dynamic Gravimetric Analysis, DGA) has been developed and used to determine the corrosion produced in carbon steel A516Gr70 samples induced by different salt mixtures commonly used as molten salts containing different amounts of chloride, at working temperatures conditions. The results show that the higher is the content of chloride in molten salts the greater is the steel loss produced by corrosion and makes the corrosive kinetics to be highly increased when it is overtaken., The research leading to these results has received funding from Spanish government (Cdti-Fondo tecnológico IDI-20090393, ConSOLida Cdti-CENIT 2008-1005). The work is partially funded by the Spanish government (ENE2011-22722). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under Grant agreement no PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under Grant agreement no 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to the research group DIOPMA (2014 SGR 1543). Dr. Camila Barreneche would like to thank Ministerio de Economía y Competitividad de España for her Grant Juan de la Cierva FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Advances in the valorization of waste and by-product materials as thermal energy storage (TES) materials

  • Gutiérrez, Andrea
  • Miró, Laia
  • Gil, Antoni
  • Rodríguez Aseguinolaza, Javier
  • Barreneche Güerisoli, Camila
  • Calvet, Nicolas
  • Py, Xavier
  • Fernández Renna, Ana Inés
  • Grágeda, Mario
  • Ushak, Svetlana
  • Cabeza, Luisa F.
Today, one of the biggest challenges our society must face is the satisfactory supply, dispatchability and management of the energy. Thermal Energy Storage (TES) has been identified as a breakthrough concept in industrial heat recovery applications and development of renewable technologies such as concentrated solar power (CSP) plants or compressed air energy storage (CAES). A wide variety of potential heat storage materials has been identified depending on the implemented TES method: sensible, latent or thermochemical. Although no ideal storage material has been identified, several materials have shown a high potential depending on the mentioned considerations. Despite the amount of studied potential heat storage materials, the determination of new alternatives for next generation technologies is still open. One of the main drawbacks in the development of storage materials is their cost. In this regard, this paper presents the review of waste materials and by-products candidates which use contributes in lowering the total cost of the storage system and the valorization of waste industrial materials have strong environmental and societal benefits such as reducing the landfilled waste amounts, reducing the greenhouse emissions and others. This article reviews different industrial waste materials that have been considered as potential TES materials and have been characterized as such. Asbestos containing wastes, fly ashes, by-products from the salt industry and from the metal industry, wastes from recycling steel process and from copper refining process and dross from the aluminum industry, and municipal wastes (glass and nylon) have been considered. Themophysical properties, characterization and experiences using these candidates are discussed and compared. This review shows that the revalorization of wastes or by-products as TES materials is possible, and that more studies are needed to achieve industrial deployment of the idea., The work is partially funded by the Spanish government (ENE2011-28269-C03-02, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from the European Union׳s Seventh Framework Programme (FP7/2007–2013) under Grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). The work at CIC Energigune was supported by the Department of Industry, Innovation, Commerce and Tourism of the Basque Country government through the ETORTEK CIC Energigune-2013 research program no. IE 13-375. Research at Masdar Institute is supported by the Government of Abu Dhabi to help fulfil the vision of the late President Sheikh Zayed bin Sultan Al Nayhan for sustainable development and empowerment of the UAE and humankind under no. SG2014-000002. Researchers of PROMES address all their gratitude to the French government for the funding of their work through the ANR SESCO and SACRE projects within the ANR SEED program. They also acknowledge the support of the CNRS, the University of Perpignan Via Domitia and the EUROPLASMA/INERTAM Company. The work at the University of Antofagasta was supported by FONDECYT (Grant No. 1120422), CONICYT/FONDAP No. 15110019, and the Education Ministry of Chile Grant PMI ANT 1201. Andrea Gutierrez would like to acknowledge to the Education Ministry of Chile her doctorate scholarship ANT 1106 and CONICYT/PAI No. 7813110010.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental evaluation of a heating radiant wall coupled to a ground source heat pump

  • Romaní Picas, Joaquim
  • Pérez Luque, Gabriel
  • Gracia Cuesta, Alvaro de
A radiant wall heating system embedded in a heavy brickwork envelope and coupled to a ground source heat pump supplied has been experimentally tested under real outdoor conditions. This system was applied to a room sized cubicle built in Puigverd de Lleida (Spain) test-site, where it was studied in system vs. system analysis in comparison to a reference cubicle built with commercial available technologies (insulated alveolar brick wall and air-to-air heat pump). The results showed the potential of the radiant wall, which in continuous operation reached energy savings between 19.97% and 40.72% based on set-point temperature. Most important, the active thermal mass of radiant wall allowed operating in off peak periods. Otherwise, this peak load shifting ability was completely inexistent in the reference cubicle. However, the results show that the radiant cubicle was unsuited to operate in occupancy schedules due to its slow response time. Furthermore, the tests show that optimization of the radiant wall system requires a control strategy that takes in account the dynamics of the system., The work partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), TIN2015-71799-C2-2-P and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. This projects has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union's Horizon 2020 research and innovation programme under grant agreement Nº 657466 (INPATH-TES) and from EEA-Grants under grant IDI-20140914. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Study of Fresh and Hardening Process Properties of Gypsum with Three Different PCM Inclusion Methods

  • Serrano, Susana
  • Barreneche Güerisoli, Camila
  • Navarro Ezquerra, Antonia
  • Haurie, Laia
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Gypsum has two important states (fresh and hardened states), and the addition of phase change materials (PCM) can vary the properties of the material. Many authors have extensively studied properties in the hardened state; however, the variation of fresh state properties due to the addition of Micronalr DS 5001 X PCM into gypsum has been the object of few investigations. Properties in fresh state define the workability, setting time, adherence and shrinkage, and, therefore the possibility of implementing the material in building walls. The aim of the study is to analyze, compare and evaluate the variability of fresh state properties after the inclusion of 10% PCM. PCM are added into a common gypsum matrix by three different methods: adding microencapsulated PCM, making a suspension of PCM/water, and incorporating PCM through a vacuum impregnation method. Results demonstrate that the inclusion of PCM change completely the water required by the gypsum to achieve good workability, especially the formulation containing Micronalr DS 5001 X: the water required is higher, the retraction is lower (50% less) due to the organic nature of the PCM with high elasticity and, the adherence is reduced (up to 45%) due to the difference between the porosity of the different surfaces as well as the surface tension difference., The work is partially funded by the Spanish government (ENE2011-28269-C03-02 and MAT2011-26410). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA-UdL (2014 SGR 123) and research group DIOPMA-UB (2014 SGR 1543) and GICITED-UPC (2014 SGR 1298). In addition, the research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n˝ PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

PCM thermal energy storage tanks in heat pump system for space cooling

  • Moreno Cermeño, Pere
  • Castell, Albert
  • Solé Cutrona, Cristian
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
A heat pump coupled to thermal energy storage (TES) tanks is experimentally tested under simulated summer conditions and the results are presented in this paper. The cold TES tank is used for shifting the cooling load of a small house-like structure. The study evaluates the thermal behaviour of the TES tank for cold storage and the application of the system for space cooling. For the analysis, two different configurations of the tanks are compared: a water tank and a PCM tank. The PCM tank is filled with a commercial macro-encapsulated PCM, which has a phase change temperature of 10 ◦C. The results point out that the PCM tank is able to supply 14.5% more cold and to maintain the indoor temperature within comfort 20.65% longer than the water tank. However, it needs 4.55 times longer to charge the tank., The research leading to these results has received funding from the [European Community’s] Seventh Framework Programme ([FP7/2007-2013] [FP7/2007-2011]) under grant agreement n◦262285 (HESTOR). The work was partially funded by the Spanish government (ENE2011-22722, ENE2011-28269-C03- 01 and ULLE10-4E-1305), with the collaboration of the City Hall of Puigverd de Lleida. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n◦ PIRSESGA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Benchmarking of energy demand of domestic and small business buildings

  • Coma Arpón, Julià
  • Maldonado, José Miguel
  • Gracia Cuesta, Alvaro de
  • Gimbernat, Toni
  • Botargues, Teresa
  • Cabeza, Luisa F.
In Europe the building sector represents 41% of the final energy consumption and the 40% of the total GHG emissions of end-use sectors (Directive 2010/31/EU) [1]. Solar energy is one of the forms of renewable energy that has great potential to enable EU the ambition of 12% of heating coming from renewable sources by 2020 [2]. Within this context, the overall objective of the project Innovative Micro Solar Heat and Power System (Innova MicroSolar) is to develop a high performance and cost effective solar heat and power system, which consist in a novel flat Fresnel mirror solar concentrating collector and micro organic Rankine cycle plant combined with advanced phase change materials as thermal storage, all system managed by smart control units. This technology will be initially implemented in individual dwellings and small business residential buildings for on-site electricity and heat generation using solar thermal energy., This study has received funding from European Union’s Horizon 2020 research and innovation programme under grant agreement Nº723596 (Innova MicroSolar) and Nº 657466 (INPATHTES), from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE). The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015- 64117-C5-3-R (MINECO/FEDER)). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental evaluation at pilot plant scale of multiple PCMs (cascaded) vs. single PCM configuration for thermal energy storage

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Cabeza, Luisa F.
The present paper provides on one hand, a literature review of the different studies available in the scientific literature where the concept of multiple phase change materials (PCM) configuration, also named cascaded or multi-stage, has been presented and on the other hand, an experimental evaluation of the advantages of using the multiple PCM configuration instead of the single PCM configuration in thermal energy storage (TES) systems at pilot plant to fill the gap of experimental and high scales studies on this concept in the literature. Two PCM with melting temperatures in a temperature range of 150 e200 C were selected due to their high value of heat of fusion and compared: d-mannitol and hydroquinone. Three configurations were evaluated: (1) single PCM with hydroquinone, (2) single PCM with dmannitol and (3) multiple PCM with hydroquinone and d-mannitol. A discussion regarding the results on the specific energy stored and effectiveness as well as the evolution of the PCM and heat transfer fluid (HTF) through the time and at different and representative locations of the facility is presented. Results showed that the multiple PCMs configuration introduced an effectiveness enhancement of 19.36% if compared with single PCM configuration as well as a higher uniformity on the HTF temperature difference between the inlet and outlet., The work is partially funded by the Spanish Government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Laia Miro would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

The connection between the heat storage capability of PCM as a material property and their performance in real scale applications

  • Mehling, Harald
  • Barreneche Güerisoli, Camila
  • Solé, Aran
  • Cabeza, Luisa F.
Using phase change materials (PCM) for Thermal Energy Storage, the most important material property is their heat storage capability, usually given as h(T). Ideally, h(T) changes suddenly at a single temperature. However, many PCM change phase in a temperature range and show hysteresis. In addition, experience shows that even measurements with the same device on the same material can give different results when the heating rate, the amount of sample mass or the equipment device are varied. The question thus arises how to deal with different h(T) results when trying to predict the performance of a real scale application. This paper identifies the main origins of these effects and gives strategies for dealing with them., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). GREA and DIOPMA are certified agents TECNIO in the category of technology developers from the Government of Catalonia. This work has been partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). Dr. Camila Barreneche and Dr. Aran Solé would like to thank Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886 and FJCI-2015-25741, respectively.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal assessment of extensive green roofs as passive tool for energy savings in buildings

  • Coma Arpón, Julià
  • Pérez Luque, Gabriel
  • Solé Cutrona, Cristian
  • Castell, Albert
  • Cabeza, Luisa F.
Sustainability trends for buildings require new construction systems to foster energy efficiency and environmentally friendly buildings. Green roofs are interesting construction systems because they provide both aesthetic and environmental benefits. This paper continues a long-term research in order to evaluate and improve the thermal behaviour and sustainability of extensive green roofs. Simultaneously this research provides experimental data for specific Mediterranean continental climate conditions. The experiment consists in evaluating the energy consumption and thermal behaviour of three identical house-like cubicles located in Puigverd de Lleida (Spain), where the only difference is the roof construction system. The roof consists of a conventional flat roof with insulation in the reference case, while in the other two cubicles the insulation layer has been replaced by a 9 cm depth extensive green roof (comparing recycled rubber crumbs and pozzolana as drainage layer materials). The electrical energy consumption of a heat pump system was measured for each cubicle during 2012 and part of 2013. Both extensive green roof cubicles show less energy consumption (16.7% and 2.2%, respectively) than the reference one during warm periods, whereas both extensive green roof systems present a higher energy consumption (6.1% and 11.1%, respectively) compared to the reference cubicle during heating periods., This work was partially funded by the Spanish Government (ENE2011-28269-C03-02 and ULLE10-4E-1305), in collaboration with the companies Gestión Medioambiental de Neumáticos S.L (Polígon Industrial Piverd s/n, Maials.) and Soprema and with the City Hall of Puigverd de Lleida. Moreover, the research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007–2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). Julià Coma would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Comparison of Microencapsulated Phase Change Materials Prepared at Laboratory Containing the Same Core and Different Shell Material

  • Giro-Paloma, Jessica
  • Alkan, Cemil
  • Chimenos Ribera, Josep Ma.
  • Fernández Renna, Ana Inés
Microencapsulated Phase Change Materials (MPCM) are widely used in active and passive systems for thermal energy storage. To evaluate the strength of a proper shell/PCM system, comparisons were performed between laboratory-prepared MPCM samples produced by in situ polymerization with a phase change temperature of 50 C and a particle size of around 1–2 m with tetracosane as PCM, and polystyrene (PS) and poly (methyl methacrylate) (PMMA) as shells. Evaluation of mechanical performance was performed for different samples by means of Atomic Force Microscopy (AFM) at different temperatures (23 C and 60 C) and with different encapsulation ratios (1:3 and 1:1, shell:core) in order to compare their properties with the PCM below and above its phase change. Evaluations of the Effective Young’s modulus (E) and deformation properties were performed for both types of MPCM. For an encapsulation mass ratio of 1:3, PS has better mechanical properties because, when increasing the temperature, the E decreases less than with PMMA. In the comparison between PS/tetracosane systems with different encapsulation mass ratios (1:3 and 1:1), E values were higher for the 1:3 encapsulation mass ratio at both temperatures under study. This means that, in terms of mechanical and thermal properties, the best combination core/shell/encapsulation mass ratio is PS/tetracosane/1:3., The work was partially funded by the Spanish government (ENE2015-64117-C5-2R). The research leading to these results received funding from the European Union’s Seventh Framework Program (FP7/2007–2013) under grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research group DIOPMA (2014 SGR 1543).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Embodied energy in thermal energy storage (TES) systems for high temperature applications

  • Miró, Laia
  • Oró Prim, Eduard
  • Boer, Dieter
  • Cabeza, Luisa F.
Currently, there is an increasing interest in concentrated solar power (CSP) plants as alternative to produce renewable electricity at large scale by using mirrors to concentrate the solar energy and to convert it into high temperature heat. These facilities can be combined with thermal energy storage (TES) systems, which are, nowadays, one of the most feasible solutions in facing the challenge of the intermittent energy supply and demand. However, they are still in research process and, for that, there is a lack of environmental impact studies of these TES systems complementing solar plants. This paper accounts the environmental impact of three TES systems used nowadays in high temperature applications for CSP plants: first, a system which stores sensible heat in high temperature concrete; second, a system storing sensible heat in molten salts; and third, another system with molten salts but storing latent heat. All the systems are normalised in order to be comparable between them due to its initial storage capacity difference. The environmental impact is accounted by calculating the amount of embodied energy in the components of the different TES systems. Notice that embodied energy refers to the total energy inputs required to make a component. Between the three systems, the sensible heat system using concrete as storage material is the one with less environmental impact while the molten salts and PCM have a higher value of embodied energy, mainly due to the nitrate mixture used as storage material. Finally, advantages and disadvantages of the method proposed used are discussed, The work was partially funded by the Spanish government (project ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2009 SGR 534). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under Grant agreement n PIRSES-GA-2013-610692 (INNOSTORAGE). Eduard Oró would like to thank the University of Lleida for his research fellowship. Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Influence of the heat transfer fluid in a CSP plant molten salts charging process

  • Peiró Bell-lloch, Gerard
  • Gasia, Jaume
  • Miró, Laia
  • Prieto, Cristina
  • Cabeza, Luisa F.
The selection of a proper heat transfer fluid (HTF) is a key factor to increase the efficiency of concentrated solar power plants and therefore, to reduce their internal associated CAPEX (capital expenditures of developing and constructing a plant, excluding any grid-connection charges) and OPEX (operating expenditures from the first year of a project's operation). This paper presents a comparative study of two commercial HTF which are widely used in different industries and CSP plants: thermal oil Therminol VP-1 and silicone fluid Syltherm 800. First, the authors theoretically studied the properties of both HTF based on the data given by the manufactures. Afterwards, the authors experimentally perform the comparison in a two-tank molten salt thermal energy storage pilot plant built at the University of Lleida (Spain). The study is focused on the plate heat exchanger of the facility during several charging processes with a counter flow arrangement. Results from both studies showed that, for the same working conditions, Therminol VP-1 is the best candidate for the above-mentioned purposes due to its higher heat transfer, lower thermal losses and lower power consumption associated to the HTF pump. However, it presents problems a low crystallization point, which should also be considered., The research leading to these results has received funding from Spanish goverment (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ULLE10-4E-1305 and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has also received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement NºPIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B1 00092). The authors would like to thank Dr. Eduard Oró from Catalonia Institute for Energy Research (Spain) and Dr. Antoni Gil from Massachusetts Institute of Technology (USA) for their help during the initial stages of the experimentation.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Infraestructura Urbana Verde: Techos Verdes y Sistemas Verdes Verticales que Brindan Múltiples Ecosistemas en el Entorno, Urban Green Infrastructure: Green Roofs and Vertical Greening Systems Providing Multiple EcoSystem Services in the Built Environment

  • Pérez Luque, Gabriel
  • Coma Arpón, Julià
El desarrollo sostenible requiere la consideración de toda una serie de elementos interconectados, como la reducción de la demanda de energía y el consumo de agua, la minimización de los residuos y la contaminación y la provisión de un transporte público eficiente. Bajo ese enfoque de “construcción sostenible”, el cierre de los ciclos de materiales y agua, así como la reducción del consumo energético son los principales objetivos en el sector de la edificación. En este contexto, el concepto de Infraestructura Verde Urbana (UGI) se ha definido como un conjunto de sistemas de construcción creados por el hombre, pero basados en la naturaleza, como techos verdes y sistemas de ecologización vertical. UGI proporciona varios eco-servicios al entorno urbano, como la reducción de la escorrentía superficial en las grandes ciudades, la reducción del efecto isla de calor, el apoyo a la biodiversidad, la mejora de la durabilidad de las membranas impermeabilizantes y el ahorro de energía en los edificios, entre otros. Durante la última década se han llevado a cabo una serie de acciones de investigación en la Universidad de Lleida con el fin de estudiar estos sistemas constructivos, cuantificar sus beneficios y mejorar su diseño. En este trabajo presentamos estos estudios., — Sustainable development requires the consideration of a whole host of interconnected elements, such as the reduction of energy demand and water consumption, minimizing waste and pollution, and providing efficient public transport. Under that “sustainable construction” approach, the closing of materials and water cycles as well as the reduction of energy consumption are the main objectives in the building sector. In this context, the concept of Urban Green Infrastructure (UGI) has been defined as a set of man-made, but nature-based, construction systems, such as green roofs and vertical greening systems. UGI provides several eco-services into the urban environment, such as the reduction of surface runoff in large cities, reduction of heat island effect, support to biodiversity, waterproofing membranes durability improvement, and building energy savings, among others. During the last decade a series of research actions have been carried out at the University of Lleida in order to study these construction systems, to quantify their benefits, and to improve their design. In this work we present these studies., All the research presented has been developed by the GREiA research group of the University of Lleida. These investigations have been partially funded by the Government of Spain (Projects: ENE2008-06687-C02-01/CON, ENE2011-28269- C03-02, ENE2011-28269-C03-03, ENE2015-64117-C5-1-R, ENE2015-64117-C5-3-R, ULLE10-4E-1305), the European Union (COST Action COST TU0802, Seventh Framework Program - FP/2007–2013 under Grant agreement No. PIRSESGA-2013-610692 - INNOSTORAGE, Horizon 2020 research and innovation program under grant agreement No. 657466 - INPATH-TES), the Government of Catalonia for the quality accreditation granted to the GREiA group during these years (2009 SGR 534, 2014 SGR 123) and to the Fundación Mapfre. The authors especially want to thank the collaboration with the companies Soprema, Gestión Medioambiental de Neumáticos S.L, y Buresinnova S.A, as well as the City Councils of Golmés and Puigverd de Lleida. Julià Coma would like to thank the Ministerio de Economia y Competitividad de España for the Juan de la Cierva Grant, FJCI-2016-30345.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Phase change material selection for thermal processes working under partial load operating conditions in the temperature range between 120 and 200 ºC

  • Gasia, Jaume
  • Martín Llop, Marc
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Cabeza, Luisa F.
In some processes, latent heat thermal energy storage (TES) systems might work under partial load operating conditions (the available thermal energy source is discontinuous or insufficient to completely charge the phase change material (PCM)). Therefore, there is a need to study how these conditions affect the discharge process to design a control strategy that can benefit the user of these systems. The aim of this paper is to show and perform at laboratory scale the selection of a PCM, with a phase change temperature between 120 and 200 ºC, which will be further used in an experimental facility. Beyond the typical PCM properties, sixteen PCMs are studied here from the cycling and thermal stability point of view, as well as from the health hazard point of view. After 100 melting and freezing cycles, seven candidates out of the sixteen present a suitable cycling stability behaviour and five of them show a maximum thermal-stable temperature higher than 200 ºC. Two final candidates for the partial loads approach are found in this temperature range, named high density polyethylene (HDPE) and adipic acid., The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA and DIOPMA (2014 SGR 123, 2014 SGR 1543). GREA and DIOPMA are certified agents TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Jaume Gasia would like to thank the Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017 FI_B1 00092). Camila Barreneche and Aran Solé would like to thank the Ministerio de Economía y Competitividad de España for Grant Juan de la Cierva FJCI-2014-22886 and FJCI-2015-25741, respectively.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal characterization of buildings from the monitoring of the AC system consumption

  • Payá, Jorge
  • Corberán, José Miguel
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Cabeza, Luisa F.
This work presents a comparative study between two buildings or cubicles with a same geometry and orientation but with different constructive layers. The mineral wool cubicle is more insulated whereas the alveolar cubicle has more thermal inertia. A novel point in this study has been to evaluate indirectly the thermal load based on the energy consumption of the heat pumps. The results indicate that the mineral wool cubicle consumes up to 7.3% less energy consumption than the alveolar cubicle, particularly in summer. In fact, the load in summer is up to 11.6% higher with the alveolar cubicle, which gains more solar energy during daytime due to its inertia. The power consumption is practically aligned with the outdoor temperatures since it is very sensitive to the operating temperatures. Nevertheless, the peak building load can take place up to 5 h later than the peak outdoor temperature, particularly in summer and in the alveolar cubicle. Finally, the proposed approach has helped obtained in situ U-values of 0.20–0.27 W m−2 K−1 for both cubicles., The work partially funded by the Spanish government (ULLE10-4E-1305). The authors from Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007–2013) under grant agreement No. PIRSES-GA-2013-610692 (INNOSTORAGE). This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 657466 (INPATH-TES). Alvaro de Gracia would like to thank the Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Phase change materials and thermal energy storage for buildings

  • Cabeza, Luisa F.
  • Gracia Cuesta, Alvaro de
It is well known that there is a need to develop technologies to achieve thermal comfort in buildings lowering the cooling and heating demand. Research has shown that thermal energy storage (TES) is a way to do so, but also other purposes can be pursued when using TES in buildings, such as peak shaving or increase of energy efficiency in HVAC systems. This paper reviews TES in buildings using sensible, latent heat and thermochemical energy storage. Sustainable heating and cooling with TES in buildings can be achieved through passive systems in building envelopes, Phase Change Materials (PCM) in active systems, sorption systems, and seasonal storage., The work partially funded by the Spanish government (ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

A simple model to predict the thermal performance of a ventilated facade with phase change materials

  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Fernàndez Camon, César
  • Cabeza, Luisa F.
Appropriate design and control strategies are crucial for the implementation of certain complex active systems in the building sector. Suitable and user-friendly numerical tools have to be available to architects and engineers, so they can incorporate innovative active systems in their building designs. The thermal response of a ventilated facade with phase change material in its air chamber for cooling applications is studied in this paper. The system makes use of low temperatures at night to solidify the phase change material, and store it solid for a later cooling supply to the interior of the building. This active technology is very sensitive to the weather conditions as well as to the defined operational schedule (charge, storage and discharge periods definition). Two different numerical approaches have been developed to better understand this system and to define different control strategies, as well as to determine their potential to reduce the energy consumption in the building for cooling purposes. First, a finite control volume approach was applied to describe the ventilated facade with latent heat storage. The important computational cost and complexity of this numerical methodology leaded the authors to develop a simple numerical model based on the assumption that the exchange between the air and phase change material inside the ventilated facade occurs at isothermal conditions. Both models were validated against experimental data, and even though the isothermal model presented slightly higher deviation from the experimental results than the finite control volume one, it is presented as a suitable numerical tool for architects and engineers because of its light computational cost and versatility., The work partially funded by the Spanish Government (ENE2011-28269-C03-01, ENE2011-22722 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Study on the optimum PCM melting temperature for energy savings in residential buildings worldwide

  • Saffari Tabalvandani, Mohammad
  • Gracia Cuesta, Alvaro de
  • Fernàndez Camon, César
  • Zsembinszki, Gabriel
  • Cabeza, Luisa F.
To maintain comfort conditions in residential buildings along a full year period, the use of active systems is generally required to either supply heating or cooling. The heating and cooling demands strongly depend on the climatic conditions, type of building and occupants' behaviour. The overall annual energy consumption of the building can be reduced by the use of renewable energy sources and/or passive systems. The use of phase change materials (PCM) as passive systems in buildings enhances the thermal mass of the envelope, and reduces the indoor temperature fluctuations. As a consequence, the overall energy consumption of the building is generally lower as compared to the case when no PCM systems are used. The selection of the PCM melting temperature is a key issue to reduce the energy consumption of the buildings. The main focus of this study is to determine the optimum PCM melting temperature for passive heating and cooling according to different weather conditions. To achieve that, numerical simulations were carried out using EnergyPlus v8.4 coupled with GenOpt® v3.1.1 (a generic optimization software). A multi-family residential apartment was selected from ASHRAE Standard 90.1- 2013 prototype building model, and different climate conditions were considered to determine the optimum melting temperature (in the range from 20ºC to 26ºC) of the PCM contained in gypsum panels. The results confirm that the optimum melting temperature of the PCM strongly depends on the climatic conditions. In general, in cooling dominant climates the optimum PCM temperature is around 26ºC, while in heating dominant climates it is around 20ºC. Furthermore, the results show that an adequate selection of the PCM as passive system in building envelope can provide important energy savings for both heating dominant and cooling dominant regions., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Program (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement No 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Development and experimental validation of a transient 2D numeric model for radiant walls

  • Romaní Picas, Joaquim
  • Cabeza, Luisa F.
  • Gracia Cuesta, Alvaro de
An experimental set-up consisting of a house like cubicle exposed to outdoor weather was used to validate a numerical model of a radiant wall. The 2D transient finite volume model used as inputs the indoor temperature, outdoor temperature, global solar radiation incident on a vertical surface, and temperature and flow of the supply water. The simulation results closely agreed with the temperature profiles and heat fluxes for the three studied orientations (East, South, and West). Furthermore, a parametric study was carried out with the radiant wall model, concluding that pipes spacing between 125 mm and 150 mm and depth between 45 mm and 65 mm minimized the temperature difference on the surface while maximizing the heat flux. Furthermore, a control strategy with shorter activation periods improved the heat transfer efficiency., The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. This projects has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from European Union's Horizon 2020 research and innovation programme under grant agreement Nº 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental study of an active slab with PCM coupled to a solar air collector for heating purposes

  • Navarro Farré, Lidia
  • Gracia, Álvaro de
  • Castell, Albert
  • Cabeza, Luisa F.
Solar energy has been widely introduced in the building market to provide electricity, heating and domes-tic hot water for a sustainable development. However, the low-density and the mismatch between energysupply and demand make appropriate its combination with thermal energy storage (TES) systems. Theintegration of these technologies (solar thermal and TES) in the building design is a key aspect to reduceenergy consumption. Latent heat storage using phase change materials (PCM) presents an advantage incomparison to conventional sensible heat storage systems due to the required volume. In this context,an innovative system that integrates PCM inside the structural horizontal building component is pre-sented in this paper. The slab consisted of a prefabricated concrete element with 14 channels filled withmacro-encapsulated PCM which is used as a storage unit and a heating supply. In order to melt the PCMthe system is coupled to a solar air collector. The prototype is tested in an experimental facility locatedin Puigverd de Lleida (Spain) where its thermal performance is evaluated under real weather conditions.This study demonstrates the high potential of the concrete slab on reducing the energy consumptioncompared to a conventional heating system., The work partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). The authors wouldlike to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and thecity hall of Puigverd de Lleida. This project has received fundingfrom the Eurpean Commission Seventh Framework Programme(FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan dela Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Numerical simulation of a finned-tube LHTES system: influence of the mushy zone constant on the phase change behaviour

  • Arena, Simone
  • Casti, Efisio
  • Gasia, Jaume
  • Cabeza, Luisa F.
  • Cau, Giorgio
This work presents a numerical investigation on latent heat thermal energy storage (LHTES) systems during the phase change process. The numerical analysis, based on the apparent heat capacity formulation, was carried out through a two-dimensional axisymmetric numerical model developed by means of the COMSOL Multiphysics software. A thermal energy storage system based on the configuration of a double tube heat exchanger with finned surfaces was used as an experimental test case and the commercial paraffin RT35 was selected as phase change material (PCM). The influence of the heat transfer by convection, in particular the influence of the term describing the mushy zone in the momentum equation, was investigated during the whole charge and discharge processes. Three different values of the constant Amush, equals to 104, 106 and 108 were selected as well as two different values of the HTF volumetric flow rate were adopted in order to reproduce both laminar and turbulent flow regimes. The results are reported in terms of temperature, melting fraction and phases evolution during the whole melting and solidification processes, and compared to previous experimental tests carried out in the laboratories of the University of Lleida, Spain. A good agreement with the experimental results was obtained showing that the mushy zone constant has a significant influence on the interface shape and motion. The results show that large values of Amush determine an increase of the mushy region reducing the natural convection effects during the charge phase. Thus, the proper evaluation of the mushy zone constant allows providing a deeper understanding of the phase change behaviour, resulting in an important parameter for accurate modelling of LHTES systems., The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). Jaume Gasia and Prof. Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017 FI_B1 00092).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Temperature distribution and heat losses in molten salts tanks for CSP plants

  • Prieto, Cristina
  • Miró, Laia
  • Peiró Bell-lloch, Gerard
  • Oró Prim, Eduard
  • Gil, Antoni
  • Cabeza, Luisa F.
Solar power plants have been deployed in the last 20 years, so the interest in evaluating their performance is growing more and more. In these facilities, thermal energy storage is used to increase dispatchability of power. The two-tank molten salts storage system with “solar salt” (60 wt.% NaNO3 and 40 wt.% KNO3) is the one commercially used today. To be able to achieve a deep understanding of the two-tank solar storage systems with molten salts, in 2008 a pilot plant was built at the University of Lleida (Spain) and the experimental evaluation of the temperature distribution inside the tanks and their heat losses are presented in this paper. Therefore, this pilot plant is equipped with several temperature sensors inside the tank as well as in the different layers of external insulation. As expected, temperature is lower at the external part of the tank (near the cover, at the bottom and near the walls) and no stratification is seen. It is found that the influencing parameters in the temperature distribution of the salts inside the tank are: insulation, and the existence of different electrical resistances and the orientation and surroundings of the tank. Heat losses were measured and compared both with a simulated 1-D steady state model and previous literature. Measured heat losses were from 61 W/m2 through the bottom to 80 W/m2 through the walls (with 73 W/m2 through the cover)., The research leading to these results has received funding from Spanish goverment (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ENE2015-64117-C5-1-R, and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement N° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal energy storage in building integrated thermal systems: A review. Part 1. active storage systems

  • Navarro Farré, Lidia
  • Gracia Cuesta, Alvaro de
  • Colclough, Shane
  • Browne, Maria C.
  • McCormack, Sarah J.
  • Griffiths, Philip
  • Cabeza, Luisa F.
Energy consumed by heating, ventilation and air conditioning systems (HVAC) in buildings represents an important part of the global energy consumed in Europe. Thermal energy storage is considered as a promising technology to improve the energy efficiency of these systems, and if incorporated in the building envelope the energy demand can be reduced. Many studies are on applications of thermal energy storage in buildings, but few consider their integration in the building. The inclusion of thermal storage in a functional and constructive way could promote these systems in the commercial and residential building sector, as well as providing user-friendly tools to architects and engineers to help implementation at the design stage. The aim of this paper is to review and identify thermal storage building integrated systems and to classify them depending on the location of the thermal storage system., The work was carried out under the framework of the COST Action BISTS TU1205. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007–2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE). The authors from the University of Lleida would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Two-tank molten salts thermal energy storage system for solar power plants at pilot plant scale: Lessons learnt and recommendations for its design, start-up and operation

  • Peiró Bell-lloch, Gerard
  • Prieto, Cristina
  • Gasia, Jaume
  • Jové, Aleix
  • Miró, Laia
  • Cabeza, Luisa F.
Renewable energies are main players to ensure the long-term energy supply. Solar power plants with thermal energy storage (TES) are one of the available renewable technologies which have more potential. Nowadays, there are still several aspects in the design and operation of these power plants which need to be improved, such as the correct operation of some specific instrumentation, the compatibility between TES materials and storage tanks materials, and operational process strategies. This paper presents the acquired experience during the design, start-up, and operation of a kWh scale pilot experimental facility built at the University of Lleida (Spain) together with Abengoa Research (Spain) in 2008. The versatility of this facility has allowed simulating real working conditions and therefore testing different TES systems, TES materials, solar power plant components, and operational strategies focused on TES for temperatures up to 400 °C. In the present paper, the authors show the lessons learnt at pilot and present the main problems and limitations encountered, and give advices of this experimental set-up to extrapolate the data to real plant, to provide solutions to technical problems and reduce the cost of commercial plants., The authors want to thank specially to Dr. Eduard Oró (today at Institut de Recerca d’Energies de Catalunya, Spain) and Dr. Antoni Gil (today at Massachusetts Institute of Technology, USA) for their help in the design, start-up and operation of the pilot plant facility. The research leading to these results has received funding from Spanish government through CDTI granted projects (Fondo tecnológico IDI-20090393, ConSOLida CENIT 2008-1005) and from Abengoa Solar NT. The work is partially funded by the Spanish government (ENE2008-06687-C02-01/CON, ENE2011-22722, ULLE10-4E-1305, and ENE2015-64117-C5-1-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123). GREA is a certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under Grant agreement NºPIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Laia Miró would like to thank the Spanish Government for her research fellowship (BES-2012-051861). Jaume Gasia would like to thank the Departament d'Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship (2017FI_B1 00092).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

PCM/wood composite to store thermal energy in passive building envelopes

  • Barreneche Güerisoli, Camila
  • Vecstaudža, Jana
  • Bajare, Diana
  • Fernández Renna, Ana Inés
The development of new materials to store thermal energy in a passive building system is a must to improve the thermal efficiency by thermal-regulating the indoor temperatures. This fact will deal with the reduction of the gap between energy supply and energy demand to achieve thermal comfort in building indoors. The aim of this work was to test properties of novel PCM/wood composite materials developed at Riga Technical University. Impregnation of PCM (phase change material) in wood increases its thermal mass and regulates temperature fluctuations during day and night. The PCM used are paraffin waxes (RT-21 and RT-27 from Rubitherm) and the wood used was black alder, the most common wood in Latvia. The PCM distribution inside wood sample has been studied as well as its thermophysical, mechanical and fire reaction properties. Developed composite materials are promising in the field of energy saving in buildings., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research group DIOPMA (2014 SGR 1543). This work has been partially funded by the Spanish government (ENE2015-64117-C5-2-R (MINECO/FEDER)). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Considerations for the use of metal alloys as phase change materials for high temperature applications

  • Fernández Renna, Ana Inés
  • Barreneche Güerisoli, Camila
  • Belusko, Martin
  • Segarra Rubí, Mercè
  • Bruno, Frank
  • Cabeza, Luisa F.
The use of paraffin, salts and salt hydrates as phase change materials (PCMs) have been researched extensively and used in a number of commercial applications. However, metals and metal alloys, which possess a high storage density on a volume basis as well as a substantially higher thermal conductivity, has received much less attention. This paper discusses the considerations for the use of metal and metal alloys as phase change materials for high temperature thermal storage applications, as well as summarises the literature on the limited research in this area. Although some pure metals and metal alloys present interesting thermal properties to be used as PCMs in thermal storage systems, there is a lack of understanding on the implications of the metallurgical aspects related to the melting and solidification of these materials under thermal cycling at high temperatures. The main issues to be considered include vapour pressure, undercooling, corrosion, segregation, changes in composition and microstructure, changes in thermal properties and undesired reactions. Further research is needed before these materials can be used as PCMs in thermal energy storage systems in industry., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 Research and Innovation Program under grant agreement No 657466 (INPATH-TES). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543), and also the Spanish Government for the projects ENE2015-64117-C5-1-R and ENE2015-64117-C5-2-R (MINECO/FEDER, UE). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886. This paper was produced with support from the “Premier’s Research Industry Fund - International Research Grant Program” (IRGP 33) funded by the Government of South Australia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental validation of a methodology to assess PCM effectiveness in cooling building envelopes passively

  • Castell, Albert
  • Farid, Mohammed M.
Energy consumption presents increasing trends during last decades, presenting a great challenge. The building sector contributes to a high proportion of the energy consumed and therefore efforts should be focused to improve energy efficiency of buildings. For such purpose, the use of phase change materials in building envelopes has been extensively studied and its benefits were demonstrated. However, there is a lack of simple evaluation tools to assess these benefits. In this paper a previously proposed methodology based on four indicators, which were tested through simulation only are experimentally validated using brick, concrete and timber constructions, incorporating PCM. Results show that the methodology is successful for buildings with heat gains and having low thermal inertia or insulation. However, for highly insulated buildings with significant inertia and low heat gains the method fails to assess the potential benefit of the PCM. Moreover, the ITD indicator is found to be the most accurate in assessing PCM benefits compared to other parameters studied. In this paper the ITD indicator will be modified to take into account an upper and lower comfort temperature levels rather than single set temperature., The research leading to these results has received funding from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013- 610692 (INNOSTORAGE). This work was partially funded by the Spanish Government (ENE2011-28269-C03-01 and ULLE10-4E- 1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2009 SGR 534) as well as to the city hall of Puigverd de Lleida.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Empirical equations for viscosity and specific heat capacity determination of paraffin PCM and fatty acid PCM

  • Barreneche Güerisoli, Camila
  • Ferrer, Gerard
  • Palacios, Anabel
  • Solé, Aran
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Phase change materials (PCM) used in thermal energy storage (TES) systems have been presented, over recent years, as one of the most effective options in energy storage. Paraffin and fatty acids are some of the most used PCM in TES systems, as they have high phase change enthalpy and in addition they do not present subcooling nor hysteresis and have proper cycling stability. The simulations and design of TES systems require the knowledge of the thermophysical properties of PCM. Thermal conductivity, viscosity, specific heat capacity (Cp) can be experimentally determined, but these are material and time consuming tasks. To avoid or to reduce them, and to have reliable data without the need of experimentation, thermal properties can be calculated by empirical equations. In this study, five different equations are given to calculate the viscosity and specific heat capacity of fatty acid PCM and paraffin PCM. Two of these equations concern, respectively, the empirical calculation of the viscosity and liquid Cp of the whole paraffin PCM family, while the other three equations presented are for the corresponding calculation of viscosity, solid Cp, liquid Cp of the whole fatty acid family of PCM. Therefore, this study summarize the work performed to obtain the main empirical equations to measure the above mentioned properties for whole fatty acid PCM family and whole paraffin PCM family. Moreover, empirical equations have been obtained to calculate these properties for other materials of these PCM groups and these empirical equations can be extrapolated for PCM with higher or lower phase change temperatures within a lower relative error 4%., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). GREA and DIOPMA are certified agents TECNIO in the category of technology developers from the Government of Catalonia. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-– 2013) under grant agreement nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement nº 657466 (INPATHTES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental set-up for testing active and passive systems for energy savings in buildings - Lessons learnt

  • Gracia Cuesta, Alvaro de
  • Navarro Farré, Lidia
  • Coma Arpón, Julià
  • Serrano, Susana
  • Romaní Picas, Joaquim
  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
This paper describes a building prototype experimental set-up used for testing active and passive systems for energy savings, presenting the used methodology, reviewing the main experimental results and identifying limitations. The test facility is located in Puigverd de Lleida (Spain) and has been experimentally evaluating different materials, technologies and systems which might be integrated in building design to provide energy savings for space heating and cooling since 2002. The research fields of passive technologies covered the effect of using different insulating materials, construction systems based on sustainable materials, addition of phase change materials in building envelopes and green infrastructures such as green roofs and walls. On the other hand, the active systems tested were focused in exploiting different available renewable energy source available, such a solar thermal, free-cooling with night air, or geothermal heat, using thermal energy storage systems to shift the heating and cooling loads., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON, ENE2011-28269-C03-02, ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). Financiado por el proyectoRTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013–2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. The research leading to these results has received funding from the European Union's Seventh Framework Programe (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE), from MOPCON Project (EU CRAFT ref. G5ST-CT-2002-50331), from Eccoinnovation Project Rewastee ECO/13/630286 and from European Union's Horizon 2020 Research and Innovation Programme under grant agreement No. 657466 (INPATH-TES) and from EEA-Grants under grant IDI-20140914. This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Julià Coma would like to thank the Departament d′Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship. Cecilia Castellón, Pablo Arce, Albert Castell, Cristian Solé, Pere Moreno and Lídia Rincón participated in the experimentation in this set-up.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Preparation and characterization of an inorganic magnesium chloride/nitrate/graphite composite for low temperature energy storage

  • Galazutdinova, Yana
  • Vega, Mariela
  • Grágeda, Mario
  • Cabeza, Luisa F.
  • Ushak, Svetlana
In this study, an inorganic mixture of 40 wt% MgCl2·6H2O and 60 wt% Mg(NO3)2·6H2O was impregnated into two types of the expanded graphite (EG): EG flakes and EG matrix. Different methods of preparation usually used in the organic composite preparation, such as direct blending, vacuum impregnation, ultrasonic impregnation and immersion were applied in this work. Considering the samples with EG matrix, it can be concluded that the optimal result of the encapsulation and ΔH ratio can be reached with the experimental time of 1, 3 and 4 h using the vacuum, ultrasound and immersion methods, respectively. Moreover, the percentage of encapsulation increases with the experimental time and with the EG percentage for the EG matrix and for the EG flakes, respectively. Concerning the supercooling phenomena, the results show that the presence of EG reduces the difference between fusion and crystallization temperature for up to 65%, acting as а nucleating agent. The resulting composite samples (CPCM) were proved to have good latent heat and a significant reduction of the supercooling effect, which eliminates the need to use nucleating agents, that are essential for pure PCM of 40 wt% MgCl2·6H2O and 60 wt% Mg(NO3)2·6H2O. Moreover, using EG suppresses significantly the melting time which indicates the heat transfer enhance of the mixture. This circumstance could allow to empower the utilization of the mentioned mixture in different fields of thermal energy storage at low temperature., Authors from Universidad de Antofagasta thank CONICYT/FONDAP N° 15110019, ERANET-LAC 2015–2016, project ELAC2015/T06-0988 and CONICYT/FONDECYT/REGULAR N° 1170675 for the financial support. Yana Galazutdinova would like to acknowledge for her doctorate scholarship to the CONICYT-PCHA/Doctorado Nacional para Estudiantes Extranjeros 2014/Folio 63140052. The work was partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER)). Dr. Luisa F. Cabeza would like to thank the Catalan Government for the quality accreditation given to her research group (2014 SGR 123). GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under Grant agreement N°PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES).
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Economic impact of integrating PCM as passive system in buildingsusing Fanger comfort model

  • Saffari Tabalvandani, Mohammad
  • Gracia Cuesta, Alvaro de
  • Ushak, Svetlana
  • Cabeza, Luisa F.
In buildings, HVAC systems consume a high amount of energy to provide thermal comfort for occupants. A methodology is presented in this paper to control thermostat operation of the buildings considering the effects of indoor and outdoor boundary conditions and phase change material (PCM) characteristics. EnergyPlus v8.1 building energy simulation software was used to analyze the energy performance of the PCM incorporated building models and to implement Fanger model to control HVAC thermostat operation according to BS EN 15251:2007 thermal comfort categories. Three types of building HVAC schedule, PCM with different melting points and layer thicknesses were studied for Madrid climate zone. Moreover, the impact of occupants clothing on the energy consumption was investigated. Furthermore, payback analysis was conducted to find out the economic benefits of PCM integration into the building envelopes. Application of PCM improved the cooling and heating energy performances except for the office model in winter (heating period). Additionally, higher energy savings and lower payback periods were observed when PCM with higher melting point was applied to the buildings. Eventually, energy savings in PCM incorporated models were found to improve further when occupants changed their clothing behavior in winter., The work is partially funded by the Spanish government (ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their researchgroup (2014 SGR 123). The research leading to these results hasreceived funding from the European Union’s Seventh FrameworkProgram (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like tothank Education Ministry of Chile for Grant PMI ANT 1201. Svetlana Ushak acknowledges to CONICYT/FONDAP no. 15110019 SERC-Chile, and PMI ANT 1201 for the financial support.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Experimental evaluation of a concrete core slab with phase change materials for cooling purposes

  • Navarro Farré, Lidia
  • Gracia Cuesta, Alvaro de
  • Castell, Albert
  • Cabeza, Luisa F.
Due to the high amount of energy consumed by the building sector, efforts need to focus not only on improving the building envelope but also on enhancing the energy efficiency of HVAC systems. In this study, an innovative technology for cooling application in buildings is evaluated. A prefabricated concrete slab incorporating phase change material (PCM) was used as internal separation in the active slab cubicle. The incorporated PCM is paraffin macro-encapsulated in aluminium tubes. The target is to use the internal slab as storage unit and as an active cooling supply to replace totally or partially conventional HVAC systems. The operational mode consists of solidifying the PCM with the outside cold air (below solidification temperature) during the night time for covering a later cooling demand. Experimental analysis shows the energy performance of the technology, as well as a comparison with a conventional cooling system., This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. The work partially funded by the Spanish Government (ENE2011-28269-C03-01 and ULLE10-4E-1305). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Passive cooling of buildings with phase change materials using whole-building energy simulation tools: A review

  • Saffari Tabalvandani, Mohammad
  • Gracia Cuesta, Alvaro de
  • Ushak, Svetlana
  • Cabeza, Luisa F.
Buildings contribute to climate change by consuming a considerable amount of energy to provide thermal comfort for occupants. Cooling energy demands are expected to increase substantially in the world. On this basis, technologies and techniques providing high energy efficiency in buildings such as passive cooling are highly appreciated. Passive cooling by means of phase change materials (PCM) offers high potential to decrease the cooling energy demand and to improve the indoor comfort condition. However, in order to be appropriately characterized and implemented into the building envelope, the PCM use should be numerically analyzed. Whole-building energy simulation tools can enhance the capability of the engineers and designers to analyze the thermal behavior of PCM-enhanced buildings. In this paper, an extensive review has been made, with regard to whole-building energy simulation for passive cooling, addressing the possibilities of applying different PCM-enhanced components into the building envelope and also the feasibility of PCM passive cooling system under different climate conditions. The application of PCM has not always been as energy beneficial as expected, and actually its effectiveness is highly dependent on the climatic condition, on the PCM melting temperature and on the occupants behavior. Therefore, energy simulation of passive PCM systems is found to be a single-objective or multi-objective optimization problem which requires appropriate mathematical models for energy and comfort assessment which should be further investigated. Moreover, further research is required to analyze the influence of natural night ventilation on the cooling performance of PCM., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINEDO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation g iven to their research group GREA (2014 SGR 123). This project has received funding from the European Commission Seventh Framework Program (FP/2007-2013) under Grant agreement Nº PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation program under grant ag reement No 657466 (INPATH-TES). Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

In situ thermal and acoustic performance and environmental impact of the introduction of a shape-stabilized PCM layer for building applications

  • Barreneche Güerisoli, Camila
  • Navarro Farré, Lidia
  • Gracia Cuesta, Alvaro de
  • Fernández Renna, Ana Inés
  • Cabeza, Luisa F.
Energy consumption in buildings accounts for up to 34% of total energy demand in developed countries. Thermal energy storage (TES) through phase change materials (PCM) is considered as a promising solution for this energetic problem in buildings. The material used in this paper is an own-developed shape stabilized PCM with a polymeric matrix and 12% paraffin PCM, and it includes a waste from the recycling steel process known as electrical arc furnace dust (EAFD), which provides acoustic insulation performance capability. This dense sheet material was installed and experimentally tested. Ambient temperature, humidity, and wall temperatures were measured and the thermal behaviour and acoustic properties were registered. Finally, because of the nature of the waste used, a leaching test was also carried out. The thermal profiles show that the inclusion of PCM decreases the indoor ambient temperature up to 3 °C; the acoustic measurements performed in situ demonstrate that the new dense sheet material is able to acoustically insulate up to 4 dB more than the reference cubicle; and the leaching test results show that the material developed incorporating PCM and EAFD must be considered a non-hazardous material., The research leading to these results has received funding from the European Commission Seventh Framework Programme (FP/2007–2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union's Horizon 2020 research innovation programme under grant agreement No 657466 (INPATH-TES). Furthermore, the work is partially funded by the Spanish government (ENE2011-28269-C03-02 and ENE2011-22722). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and DIOPMA (2014 SGR 1543). Alvaro de Gracia would like to thank Education Ministry of Chile for Grant PMI ANT 1201.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Enhanced thermal energy supply via central solar heating plants with seasonal storage: A multi-objective optimization approach

  • Tulus, Victor
  • Boer, Dieter
  • Cabeza, Luisa F.
  • Jiménez, Laureano
  • Guillén Gosálbez, Gonzalo
Central solar heating plants with seasonal storage (CSHPSS) are among the most promising technologies to save energy in the industrial and residential-commercial building sectors. This work introduces a systematic approach to optimize these systems according to economic and environmental criteria. Our method, which combines the TRNSYS 17 simulation software with life cycle assessment and multi-objective optimization, identifies optimal CSHPSS designs for any climatic condition and heating demand profile considering economic and environmental criteria simultaneously. The capabilities of this approach are illustrated through its application to a case study of a CSHPSS located in Barcelona (Spain), which satisfies a heating demand for a neighborhood of 1120 dwellings. Numerical results show that the CSHPSS plant leads to significant environmental and economic improvements compared to the use of a conventional natural gas heating system. Our tool can guide engineers and architects in the transition towards a more sustainable residential sector., The authors would like to acknowledge financial support from the Spanish Government (CTQ2012-37039-C02-01, ENE2015-64117-C5-3-R, ENE2015-64117-C5-1-R, MINECO/FEDER, UE) and to thank the Catalan Government for the quality accreditation given to the research group GREA (2014 SGR 123). The research leading to these results has received funding from the European Commission Seventh Framework Programme under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE).