Pasar al contenido principal

FUNCIONALIZACION DE MATERIALES CON TECNOLOGIAS LASER Y RETOS TECNOLOGICOS PARA MEJORAR RENDIMIENTOS EN ENERGIA RENOVABLE Y SOSTENIBLE

ENE2017-83669-C4-1-R

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 36
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Conjugate two-dimensional electric potential maps

  • Badía-Majós, Antonio
  • Lorenzo Poza, E. de
Two-dimensional electric potential maps based on voltage detection in conducting paper are common practice in many physics courses in college. Most frequently, students work on 'capacitor-like' geometries with current flowing between two opposite electrodes. A 'topographical' investigation across the embedding medium (map of equipotential curves) allows one to reassure a number of physical properties. This paper focuses on some less common configurations that bear pedagogical interest. We analyse 'open-geometries' with electrodes in the form of long strips with slits. They provide a natural groundwork to bring the student to complex variable methods. Aided by this, we show that shaping the conducting paper board one may analyse finite size effects, as well as some meaningful discontinuities in the measured potential. The concept of conjugate electric potentials is exploited. Equipotentials and electric field lines acquire interchangeable roles and may be obtained in complementary 'dual' experiments. A feasible theoretical analysis based on introductory complex variables and standardised numerics gives a remarkable quantification of the experimental results., Partial financial support from the Spanish MINECO under project ENE2017-83669-C4-1-R is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Josephson critical currents in annular superconductors with Pearl vortices

  • Badía-Majós, Antonio
We investigate the influence of Pearl vortices in the vicinity of an edge-type Josephson junction for a superconducting thin-film loop in the form of an annulus, under uniform magnetic field. Specifically, we obtain the exact analytic formulation that allows one to describe the circulating current density and the gauge invariant phase increment Δϕ across the junction. The main properties of Δϕ and their influence on the critical current pattern Ic(B) are described quantitatively in terms of the loop's width-to-radius ratio W/R and of the vortex position within the loop rv. It is shown that narrow loops (W/R<0.3) may be well described by the straight geometry limit. However, such approximation fails to predict a number of distinctive features captured by our formulation, such as the node lifting effect of the Ic(B) pattern in wide loops or the actual influence of a vortex pinned at different positions., This work was supported by Spanish Mineco, under Projects No. ENE2014-52105-R and No. ENE2017-83669-C4-1-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Metal films by laser ablation backwriting on glass

  • Angurel, Luis A.
  • Molina Mansilla, Ricardo
  • Rico, Víctor J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
  • Muñoz Rojas, David
  • Huerta, C. M. de la
  • Nguyen, V. H.
  • Fuente, Germán F. de la
Resumen del trabajo presentado a la Science and Applications of Thin Films, Conference & Exhibition; celebrada en Izmir (Turquia) del 17 al 21 de septiembre de 2018., The use of lasers to achieve transformations at interfaces, either on solids under air, controlled atmospheres or a diversity of liquid environments, is evolving at a fast pace and in-line with recent advances in photonic technologies. The singular properties of lasers, which provide a choice of emission parameters, such as emission wavelength, pulsed or cw mode and pulse width, together with the use of optomechanical means to scan in beam or line fashion, are ideal in order to trigger physico-chemical phenomena which are not available with alternative methods and are, at large, based on thermally activated processes. Recently developed methods in our Laboratories include those that are based, on the one hand, on strongly photothermal interactions; on the other, on mixed type interactions, where photothermal, photophysical and, in some cases, photochemical types may cohexist. In the former case, a solid may melt and, with the controled laser movement, directionally solidify into a material with controlled microstructure. In the latter case, an ablation process with extreme physical or chemical consequences may be triggered and be localised at the irradiated interface. A brief description of the phenomena behind laser-solid interactions will be presented, along with results obtained with the Laser Ablation Backwriting (LAB) method and applied to surface modification of glass. This has been recently developed in order to modify physico-chemical and functional properties of glass surfaces at large, based on this fully scaleable method. In particular, selective metallization of glass surfaces will be addressed in this talk., This research is partially supported by projects MAT2016-79866-R, ENE2017-83669-C4-1-R (Agencia Estatal de Investigación & Programa FEDER), PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FETOPEN 801464)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

IR laser line scanning treatments to improve levitation forces in MgTi0.06B2 bulk materials

  • Ozturk, K.
  • Aksoy, C.
  • Angurel, Luis A.
  • Savaskan, B.
  • Martínez Fernández, Elena
  • Badía-Majós, Antonio
  • Fuente, Germán F. de la
  • Guner, B.
  • Dancer, C.E.J.
  • Celik, S.
Infrared (IR) laser-line scanning has been widely used to induce different surface microstructures in a broad range of materials. In this work, this laser configuration was applied on the surface of MgTi0.06B2 bulk samples in order to ascertain its effects on their superconducting properties, particularly on the magnetic levitation forces. The microstructural changes produced by this type of laser treatment were investigated by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). It was observed that the thermal treatment induced by the laser improves grain connectivity in a layer of material just below the irradiated surface, in agreement with the observed improvement in critical current density values, Jc, which were estimated from isothermal magnetic hysteresis loops. A significant increment of both vertical (Fz) and lateral (Fx) magnetic levitation forces was achieved. Numerical calculations were performed to understand the experimental behaviour and to clarify how an improvement of Jc near the surface can improve the magnetic levitation force of these materials. In addition, the same studies were carried out in similar bulk samples but with nano-sized silver particle additions of 3 and 6 wt %, in the outer ring of the bulk, observing also an improvement of the levitation forces, albeit less than in samples without Ag because of the better performance of the original samples after laser treatment. These results are relevant to those studying superconductor fabrication and material fabrication modelling, essential for the development of technological applications of superconductors, and are based on microstructure control via application of a recently developed laser-line scan method., As authors, we would like to thank the Scientific and Technological Research Council of Turkey (TUBITAK with program code 2219), the Spanish Agencia Estatal de Investigación and the European FEDER Program (project ENE2017-83669-C4-1-R), and the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza and Erzincan University in Turkey for microstructural characterization., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effects of laser-induced periodic surface structures on the superconducting properties of Niobium

  • Cubero, A.
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
  • Legall, H.
  • Krüger, J.
It is well known that the use of ultrashort (fs) pulsed lasers can induce the generation of (quasi-) periodic nanostructures (LIPSS, ripples) on the surface of many materials. Such nanostructures have also been observed in sample’s surfaces irradiated with UV lasers with a pulse duration of 300 ps. In this work, we compare the characteristics of these nanostructures on 1-mm and on 25-μm thick niobium sheets induced by 30 fs n-IR and 300 ps UV pulsed lasers. In addition to conventional continuous or burst mode processing configurations, two-dimensional laser beam and line scanning modes have been investigated in this work. The latter allows the processing of large areas with a more uniform distribution of nanostructures at the surface. The influence of the generated nanostructures on the superconducting properties of niobium has also been explored. For this aim, magnetic hysteresis loops have been measured at different cryogenic temperatures to analyse how these laser treatments affect the flux pinning behaviour and, in consequence, the superconductor’s critical current values. It was observed that laser treatments are able to modify the superconducting properties of niobium samples., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1) and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Comparison of nanostructures formed on Nb using fs near-IR and ps UV pulsed lasers

  • Cubero, A.
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
  • Legall, H.
  • Krüger, J.
  • Bonse, J.
Trabajo presentado al Spring Meeting of the European Materials Research Society (E-MRS), celebrado del 27 al 31 de mayo de 2019 en Niza (Francia)., It is well known that the use of ultrashort (fs) pulsed lasers can induce the generation of (quasi-) periodic nanostructures (LIPSS, ripples) on the surface of metallic samples. Such nanostructures have also been observed in sample's surfaces that have been irradiated with UV lasers with a pulse duration of 300 ps. In this work, we compare the characteristics of these nanostructures on 25-micrometer thick Nb sheets induced by different pulsed lasers, and we analyze the influence of the different parameter conditions that were selected for the laser processing. In addition to conventional continuous or burst mode processing configurations, a meandering laser line scanning has also been investigated. This configuration allows the processing of large areas with a more uniform distribution of nanostructures at the surface. The influence of these nanostructures on the superconducting properties of Nb has also been investigated. With this aim, magnetic hysteresis loops have been measured at different temperatures to analyze how these laser treatments can affect the flux pinning behavior and, in consequence, their critical current values., European FEDER Program, Spanish Ministerio de Economía y Competitividad (Agencia estatal de Investigación) and Gobierno de Aragón (Research group T54_17R) through project ENE2017-83669-C4-1-R ., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Influence of crystallographic texture and external electromagnetic fields on sub-ns pulsed UV laser derived nanostructures

  • Porta-Velilla, L.
  • Cubero, A.
  • Castro, Miguel
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
Resumen del trabajo presentado al European Congress and Exhibition on Advanced Materials and Processes (EUROMAT), celebrado en Estocolmo (Suecia) del 1 al 5 de septiembre de 2019., [Introduction/Purpose]: Generation of Laser-induced Periodic Surface Structures (LIPSS) is a general phenomenon that has been observed in a broad range of materials and intensively studied since the commercial availability of ultra-short pulsed lasers. It has been observed that the morphology of LIPSS can be controlled by the selection of adequate laser processing parameters., [Methods]: In this work, we have analysed the generation of LIPSS in different metal surfaces using a sub-ns (300 ps) pulsed UV laser, with a laser-line scanning configuration. In addition to the laser parameters, different variables that can modify how LIPSS are generated, have been explored. EBSD studies have been used to determine the crystallographic direction of each grain at the surface of the material and how it modifies the characteristics of nanostructure generation. Experiments have also been performed under different electromagnetic fields during laser processing., [Results]: It has been observed that crystallographic orientation of grains has a significant influence on the generation of nanostructures. When prominent cones are generated, they appear only in some grains with a given orientation, for instance, (001) planes in stainless steel. In the case of ripples, period, size and orientation are also modified. For some configurations of external electromagnetic fields, the uniformity of the nanostructure can also be improved in extended areas., [Conclusions]: It is well established that nature and ordering of LIPSS nanostructures depend on the laser parameters, mainly irradiance and polarization, and on the material. In this work, it has been determined that for a given material, this order can be modified depending on the crystallographic orientation of each particular grain and using adequate external electromagnetic fields., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Metal surface nanostructures developed with sub-ns UV laser line scanning under different atmospheres

  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Cubero, A.
  • Porta-Velilla, L.
  • Castro, Miguel
  • Rojo, J. A.
  • Martínez Fernández, Elena
  • Navarro, Rafael
Resumen del trabajo presentado al International Symposium Fundamentals of Laser Assisted Micro- & Nanotechnologies (FLAMN), celebrado en San Petersburgo (Rusia) del 30 de junio al 4 de julio de 2019., Work financed by MAT2016-79866-R & ENE2017-83669-C4-1-R (MINECO-AEI-FEDER, UE), PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) and Aragón Government (Research Group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Quench dynamics in different configurations of MgB2 Rutherford cables

  • Martínez Fernández, Elena
  • Navarro, Rafael
  • Cubero, A.
  • Kováč, P.
  • Kopera, L.
Trabajo presentado a la 14th European Conference on Applied Superconductivity (EUCAS), celebrada en Glasgow (Escocia) del 1 al 5 de septiembre de 2019., This work was supported by project ENE-2014-52105-R and ENE2017-83669-C4-1-R (from Spanish Ministerio de Ciencia, Innovación y Universidades, Agencia Estatal de Investigación (AEI) and European FEDER Program) and by the Slovak Scientific Agency under the APVV-14-0522 project. Authors also would like to acknowledge the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R) and the “Servicio General de Apoyo a la Investigación-SAI” of the University of Zaragoza and Matt Rindfleisch (HyperTech Research, Inc) for providing the NiCu-sheathed wires for cable manufacture., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Thermal stability of conduction-cooled no-insulated HTS coils at currents up to 400 A

  • Cubero, A.
  • Núñez-Chico, A. B.
  • Navarro, Rafael
  • Angurel, Luis A.
  • Martínez Fernández, Elena
Trabajo presentado a la 14th European Conference on Applied Superconductivity (EUCAS), celebrada en Glasgow (Escocia) del 1 al 5 de septiembre de 2019., This work was supported by Spanish Ministerio de Ciencia, Innovación y Universidades, Agencia Estatal de Investigación (AEI) and European FEDER Program (projects ENE-2014-52105-R and ENE2017-83669-C4-1-R) and by the regional Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Electromagnetic behaviour and thermal stability of a conduction-cooled, no-insulated 2G-HTS coil at intermediate temperatures

  • Cubero, A.
  • Núñez-Chico, A. B.
  • Navarro, Rafael
  • Angurel, Luis A.
  • Martínez Fernández, Elena
The electromagnetic and thermal properties of a double pancake coil made of second generation high temperature superconductor, 2G-HTS, have been studied. The coil was wound with no-insulation between turns (NI coil) and was later impregnated with epoxy resin and glued to a copper support plate. The coil was thermally anchored to the cryocooler cold finger and cooled by conduction. After several thermal cycles no degradation of its superconducting properties was observed. The coil was operated under high vacuum and high currents (up to 400 A in steady conditions) at different temperatures in the range between 5 K and 77 K, with special focus on the analysis above 30 K. The charge and discharge characteristics, and the experimentally measured and numerically estimated critical currents, have been studied. The different loss contributions during current ramp and the thermal contact conductance between different parts of the double pancake coil have been measured. The implications of these two factors on the thermal stability and the behaviour of the whole cryogenic system are discussed., This work was supported by projects ENE2017-83669-C4-1-R (MINECO/AEI/FEDER, EU) and ENE-2014-52105-R (MINECO/FEDER, EU) and by the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R). The authors acknowledge the use of Servicio General de Apoyo a la Investigación-SAI, University of Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Laser induced high temperature surface chemistry

  • Rey-García, F.
  • Rico, Víctor J.
  • Bao-Varela, C.
  • Angurel, Luis A.
  • González-Elipe, Agustín R.
  • Fuente, Germán F. de la
Resumen del póster presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Ceramic tiles are widely used as construction materials because of their outstanding mechanical properties (high strength, hardness, toughness and abrasion resistance), chemical inertness and aesthetic appearance. Concomitantly, a variety of new functionalities have been demonstrated during recent years, by developing appropriate frit and glaze compositions. Laser processing has been intensively utilized to improve surface characteristics, either applying ablative laser regimes or intense mid-IR emission beams that enable high temperature surface melting. In this context, in addition to the numerous thermal annealing procedures reported in the literature and applied to industry to modify the surface properties of ceramics, a novel Laser Furnace (LF) method has been recently patented. It enables modifying the surface finish of solids by inducing high temperature (1500-3000 °C) reactions at surfaces and interfaces, while maintaining volume temperatures at relatively low values (i.e. below 1200 °C). This paper deals with the application of this laser technology to the coloring of ceramic tiles previously deposited with either metal and oxide precursor thin films, or, alternatively with noble metal-organic layers. These layer/tile systems have been treated both, with nIR ns pulsed lasers and by cw CO2 lasers with emission in the mid-IR. The latter were coupled into a roller furnace to induce chemical processes which result in a variety of coloring effects., The authors gratefully acknowledge funding from MICINN and AEI (ENE2017-83669-C4-1-R and MAT2016-79866-R), FEDER/EU (project SPRINT (EU H2020-FET-OPEN/0426)) and Gobierno de Aragón (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Laser line scanning for large area surface microstructure control

  • Santos, H.
  • Angurel, Luis A.
  • Trujillo, F. J.
  • Muñoz Rojas, David
  • Masse, C.
  • Nguyen, V. H.
  • Bea, J. A.
  • Fuente, Germán F. de la
Resumen del póster presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Large-scale industrial materials must comply with crucial requirements beyond their technical specifications. The overall economy of any material system designed is a priority, leading to a complex equilibrium between costs and performance. Ultimate feasibility assessments rely on materials design efforts, particularly in processes exposed to extreme corrosive environments as well as those with high quality requirements in terms of interfacial defects in multilayer devices. In such systems surface engineering plays a key role, offering the means to maximize the life span of a certain material system. In parallel to the intrinsic cost savings derived in terms of maintenance, certain techniques allow an extreme control of the processing conditions, resulting in lower consumption of reactants, time and energy. This is the case of laser surface processing, particularly regarding laser line scanning (LLS). Such technique combines the transverse movement of a target with the fixed scanning linear movement of the laser spot along the axis perpendicular to the probe’s displacement. This technique has been applied to well-studied systems as Fe-Al protective coatings, rendering useful development paths to improve the alloying performance addressing subjects as: grain microstructure orientation, stoichiometric gradients smothering, segregation dispersion or interface defects density. The present work takes into account the above considerations, in an attempt to adapt this novel Laser Line Scanning method to process functional metal oxide coatings. With the help of standard simulation models, attempts to densify coated surfaces, as well as to control microstructure, will be described., The authors gratefully acknowledge the financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades, Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from EU (project SPRINT (EU H2020-FETOPEN/0426), PHOBIC2ICE (EU GA 690819)), and from the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Effect of UV picosecond pulse laser irradiation of Nb surfaces on their magnetic flux pinning

  • Cubero, A.
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
  • Dai, Guoqing
  • Li, Hongtao
  • Cui, Yuwen
Trabajo presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Física celebrada en Zaragoza del 15 al 19 de julio de 2019., In this work we study the interaction of surface periodic nanostructures induced by Pulsed Laser Sources (PLS) in the superconducting properties of metallic Nb. The aim is to search new ways to up-grade the fabrication and processing of Nb Superconducting Radio-Frequency (SRF) cavities used in particle accelerators and to advance in the understanding of high speed PLS manufacture of periodic surface nanostructures (ripples, grooves, spikes, microholes) in metals largely unexplored at the fundamental levels., European FEDER program, Spanish Ministerio de Economía y Competitividad project ENE2017-83669-C4-1-R. Gobierno de Aragón (Research group T54_17R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Generation of nanostructures in metallic surfaces using subnanosecond UV laser processing

  • Cubero, A.
  • Porta-Velilla, L.
  • Castro, Miguel
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Martínez Fernández, Elena
  • Navarro, Rafael
Resumen del trabajo presentado a la International Conference on Condensed Matter and Materials Science (ICCMMS), celebrada en Adana (Turquia) del 14 al 19 de octubre de 2019., In this work we present the rich surface structure phenomenology that has been observed when the surface of different metals (Nb, Ni, steel) is irradiated with a subnanosecond (300 ps) UV laser, and how it affects some of their properties. The influence of different laser parameters, as the laser polarization direction, the pulse irradiance, laser scanning speed and the overlapping in the perpendicular direction, have been studied and a complete set of nanostructures have been defined. Laser treatments have been performed in air, but also in controlled atmospheres (Ar, N2) or with the surface immersed in liquids (Vaseline oil, water) observing that the generated nanostructures are different depending on the particular experimental conditions imposed. An important effort has been carried out in order to obtain homogeneous nanostructures over extended areas, using a new laser line scanning protocol. In these studies, it has been observed that not only the laser parameters affect the generated nanostructure, but some materials properties are also important. Combining laser treatments with EBSD studies it has been demonstrated that crystallography also plays an important role in the generated nanostructure, observing that the level of interaction of the laser with a particular grain has some correlation with its crystallographic order. It has ben also observed that, in depending on the properties of the materials, nanostructures can be modified by the application of external electromagnetic fields., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

MgB2 cables made of thin wires manufactured by IMD process

  • Kováč, P.
  • Kopera, L.
  • Hain, M.
  • Martínez Fernández, Elena
  • Kováč, P.
  • Melišek, T.
  • Berek, D.
  • Hušek, I.
This paper presents the properties of cables made of thin MgB2 wires with different sheaths manufactured by IMD process. Strong effect of the outer sheath on the J e(B) performance was observed and the best properties were obtained for the strongest Cu sheath. It was found that the transversal and longitudinal cables uniformity affects the critical currents in MgB2 wires made by IMD considerably. We have analyzed the quench dynamics in Rutherford cables with Al + 1.5%Al2O3 sheath, when subjected to heat disturbances. Quench triggered in the strands in direct contact with the heater, observing important delays in quench development among strands. Low AC losses were measured for the extra-light Rutherford cable with Ti barrier and Al + 1.5%Al2O3 sheath due to an increased barrier resisitivity and surface Al sheath oxidation, which reduces coupling current loss component effectivelly., This work was supported by the Slovak Scientific Agency under projects APVV-18-0271, APVV-14-0719 and VEGA 2/0140/19. The authors acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1) and from Gobierno de Aragon ‘Construyendo Europa desde Aragon (research group T54_17 R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigacion-SAI, Universidad de Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High speed processing of NiFe2O4 spinel using a laser furnace

  • Özçelik, Bekir
  • Özçelik, S.
  • Amaveda, H.
  • Santos, H.
  • Borrel, C. J.
  • Sáez-Puche, R.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
The Laser Furnace (LF) method has been applied to directionally solidify NiFe2O4 spinel disks from a mixture of Fe and Ni oxides in order to obtain uniform, dense targets for controlled synthesis of spinel nanoparticles via Laser Ablation. Application of a CO2 laser in Line Scan mode onto a sample with the desired stoichiometry, enabled melt processing above 1580 °C at its outer surface layer. This process was carried out inside a continuous roller furnace at a maximum volume temperature of 1000 °C. Such combination helps avoid excessive thermal stress, crack formation and catastrophic failure of these magnetic ceramic monoliths. Higher energy incubation values yield increased molten volumes and a thicker resolidified surface layer with a dense microstructure. Despite the high solidification rates imposed, NiFe2O4 spinel is the main phase obtained according to X-Ray Diffraction (XRD) and magnetization studies. LF processed samples exhibit a reduction of the coercive fields and an increase of the saturation magnetization values, evidence for soft ferromagnetism and characteristic of the magnetic behaviour associated with this spinel. This work demonstrates the convenience of the LF method for preparation of uniform, dense targets for Laser Ablation and other evaporation based techniques used in the fabrication of nanoparticles., The authors acknowledge financial support from MINECO-AEI-FEDER, EU (projects MAT2016-79866-R and ENE2017-83669-C4-1-R) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Surface superconductivity changes of niobium sheets by femtosecond laser-induced periodic nanostructures

  • Cubero, Álvaro
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
  • Legall, Herbert
  • Krüger, Jörg
  • Bonse, Jörn
This article belongs to the Special Issue Laser-Generated Periodic Nanostructures., Irradiation with ultra-short (femtosecond) laser beams enables the generation of sub-wavelength laser-induced periodic surface structures (LIPSS) over large areas with controlled spatial periodicity, orientation, and depths affecting only a material layer on the sub-micrometer scale. This study reports on how fs-laser irradiation of commercially available Nb foil samples affects their superconducting behavior. DC magnetization and AC susceptibility measurements at cryogenic temperatures and with magnetic fields of different amplitude and orientation are thus analyzed and reported. This study pays special attention to the surface superconducting layer that persists above the upper critical magnetic field strength Hc2, and disappears at a higher nucleation field strength Hc3. Characteristic changes were distinguished between the surface properties of the laser-irradiated samples, as compared to the corresponding reference samples (non-irradiated). Clear correlations have been observed between the surface nanostructures and the nucleation field Hc3, which depends on the relative orientation of the magnetic field and the surface patterns developed by the laser irradiation., This work was funded by project ENE2017-83669-C4-1-R (MCIU/AEI/FEDER, EU) and by the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina Mansilla, Ricardo
  • Ertuğrul, M.
  • Navarro, Rafael
  • Rico, Víctor J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laserinduced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces., This paper is dedicated to the memory of Prof. Rafael Navarro. The authors gratefully acknowledge the financial support from Spanish MINECO-AEI and EU FEDER Program (projects ENE2017-83669-C4-1-R and MAT2016-79866-R), from EU project SPRINT (H2020-FETOPEN 801464) and from the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R). Authors also would like to acknowledge the use of Servicio General de Apoyo a la Investigación-SAI and the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas” at University of Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improved copper–epoxy adhesion by laser micro- and nano-structuring of copper surface for thermal applications

  • Mora Alfonso, Mario
  • Amaveda, H.
  • Porta-Velilla, Luis
  • Fuente, Germán F. de la
  • Martínez Fernández, Elena
  • Angurel, Luis A.
This article belongs to the Special Issue Advanced Epoxy-Based Materials II., The objective of this work is the enhancement of metal-to-metal bonding to provide high thermal conductivity together with electrical insulation, to be used as heat sinks at room and cryogenic temperatures. High thermal conductive metal (copper) and epoxy resin (Stycast 2850FT) were used in this study, with the latter also providing the required electrical insulation. The copper surface was irradiated with laser to induce micro- and nano-patterned structures that result in an improvement of the adhesion between the epoxy and the copper. Thus, copper-to-copper bonding strength was characterized by means of mechanical tensile shear tests. The effect of the laser processing on the thermal conductivity properties of the Cu/epoxy/Cu joint at different temperatures, from 10 to 300 K, is also reported. Using adequate laser parameters, it is possible to obtain high bonding strength values limited by cohesive epoxy fracture, together with good thermal conductivity at ambient and cryogenic temperatures., This work was funded by project ENE2017-83669-C4-1-R (MCIU/AEI/FEDER, EU) and by the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Large enhancement of thermal conductance at ambient and cryogenic temperatures by laser remelting of plasma-sprayed Al2O3 coatings on Cu

  • Cubero, Álvaro
  • Martínez Fernández, Elena
  • Fuente, Germán F. de la
  • García Cano, Irene
Joints of high thermal contact conductance and electrical insulation have been obtained by coating copper supports with thin alumina (Al2O3) layers (of 140–150 μm thickness). This has been achieved by a combination of plasma spraying process and the subsequent coating remelting by a near-Infrared (n-IR) laser. With a proper optimization of the laser processing conditions, it is possible to transform the metastable γ-Al2O3 phase of the as-sprayed coatings to stable α-Al2O3, and to achieve denser alumina coatings. This results in a large enhancement of the thermal conductance of the joints, enabling their application as heat sinks at cryogenic and ambient temperatures. The process proposed in this work is scalable for the formation of alumina coatings on large metallic pieces of complex geometries., This work was funded by project ENE2017–83669-C4–1-R (MCIU/AEI/FEDER, EU), by the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R) and Generalitat de Catalunya for the project SGR2017_01777. The authors acknowledge the use of Servicio General de Apoyo a la Investigación-SAI at the University of Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improvement of flexural bond strength of zirconia-resin cement by surface patterning using sub-nanosecond UV laser

  • Akay, Canan
  • Turan, Neslihan
  • Karakış, Duygu
  • Angurel, Luis A.
Zirconia is a dental material that shows excellent biocompatibility and high strength in clinical applications. This study aims to evaluate the effects of ultrafast laser applications. The surface nanostructures were classified into three groups. Group 1 was generated using the burst mode, with three different distances between dots: 52 µm (Group 1a), 104 µm (Group 1b), and 156 µm (Group 1c). Group 2 was processed using the scanning mode configuration, with a set of parallel lines. Group 3 was also processed using this scanning configuration creating a set of square-shaped patterning. Group 4 was the control group. After the surface treatments, a pair of zirconia specimens was bonded end to end with resin cement. Flexural bond strength (FBS) test was applied in a universal test machine. Multiple comparisons were performed using a one-way analysis of variance and the Tukey's HSD test. All the samples that were treated with the laser showed higher FBS values than the untreated surface. Using the burst mode, preformed circular-shaped surface on an angle of 900 at 52 µm distance (Group 1a) showed the highest FBS values among all groups (p < .05). Groups 2 and 3 had significantly higher values than 1b and 1c., The authors thank the Spanish MINECO, Agencia Estatal de Investigación and the European FEDER Program (project ENE2017-83669-C4-1-R), and the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structure, magnetic, photocatalytic and blood compatibility studies of nickel nanoferrites prepared by laser ablation technique in distilled water

  • Özçelik, Sezen
  • Yalçın, B.
  • Arda, L.
  • Santos, H.
  • Sáez-Puche, R.
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Özçelik, Bekir
The main objective of this study is to investigate the structural features, magnetic behaviour, photocatalytic properties and blood compatibility of NiFe2O4 nanoparticles (NPs) obtained by subnanosecond laser ablation in water. Structure and size distribution of NPs were studied using X-Ray Diffractometry (XRD) and Transmission Electron Microscopy (TEM). The photocatalytic properties of NPs were evaluated by photo-degradation of Methylene Blue (MeB) dye under ambient visible light illumination. Four different kinetic models were used to identify the photocatalytic degradation mechanism of NiFe2O4 nanoparticles and it was found that the pseudo-second-order model was the most suitable type to interpret the experimental kinetic data of MeB photodegradation. The hemocompatibility of NiFe2O4 nanoparticles was studied by hemolysis tests using human erythrocytes drawn from healthy volunteers. NiFe2O4 nanoparticles caused undesirable hemolysis ratios at 0.05, 1 and 5 mg/ml concentrations, while the biologically safe concentration of these nanoparticles was found to be below 0.01 mg/ml., The authors acknowledge financial support from Spanish MINECO-AEI-FEDER EU (project ENE2017-83669-C4-1-R) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_20R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Laser remelting of Al2O3 coatings on Cu: A way to increase thermal conductance in heat sinks

  • Cubero, Álvaro
  • Martínez Fernández, Elena
  • Fuente, Germán F. de la
  • Cano, I. G.
  • Dosta, S.
  • Angurel, Luis A.
Trabajo presentado al 2nd International Symposium on Applied Sciences and Engineering (ISASE), celebrado online del 7 al 9 de abril de 2021., This work is founded by MCIU/AEI/FEDER, EU (ENE2017-83669-C4-1-R), by Gobierno de Aragón (Research group T54_20R) and by Generalitat de Catalunya (SGR2017_01777)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Experimental and numerical investigation of levitation force parameters of novel multisurface Halbach HTS–PMG arrangement for superconducting Maglev system

  • Ozturk, Kemal
  • Badía-Majós, Antonio
  • Abdioglu, Murat
  • Burak Dilek, Durukan
  • Gedikli, Hasan
We have designed multisurface Halbach high temperature superconductor-permanent magnetic guideway (HTS-PMG) arrangements for magnetically levitated transportation (Maglev) and investigated the static force parameters in addition to the dynamic response characteristics. Three different Halbach HTS-PMG arrangements were used with multisurface (6 HTS, 4 HTS) and single surface (2 HTS) configurations and static and dynamic measurements were carried out in three different field cooling heights (FCHs). The bigger vertical loading capacity and wider loading gap were obtained with multisurface Halbach HTS-PMG arrangements. In addition, nearly four times bigger guidance force values of multisurface arrangements than that of single surface one indicates that the side HTSs in multisurface arrangements make a significant contribution to the guidance force and thus lateral movement stability of Maglev systems. Both the vertical and lateral dynamic stiffness values increased with decreasing FCH and it can be also said that the dynamic stiffness properties of Maglev systems can be enhanced especially in lateral direction by using the multisurface Halbach HTS-PMG arrangements. Understanding of these experimental observations is supported by dedicated theoretical modelling through a 2-D approximation of the system. We show that by using a single material parameter (the critical current density J c ) for the whole superconducting set, one may satisfactorily predict the complete series of experiments. The static and dynamic parameters obtained from this study and the results of dedicated theoretical modeling for single-surface and multisurface HTS-PMG arrangements are thought to be helpful for the researchers working on static and dynamic performances of HTS Maglev systems., This work was supported by the Scientific and Technological Research Council of Turkey (TUBITAK – Turkey), with project number 118F426. The authors thank technician L. Demir in department of mechanical engineering for his help in the experimental setup. A. Badía-Majós acknowledges support from the Spanish Agencia Estatal de Investigación and the European FEDER Program (project ENE2017-83669-C4-1-R), and the Gobierno de Aragón (research group T54_17R)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Josephson critical currents in annular superconductors with Pearl vortices

  • Badía-Majós, A.
We investigate the influence of Pearl vortices in the vicinity of an edge-type Josephson junction for a superconducting thin-film loop in the form of an annulus, under uniform magnetic field. Specifically, we obtain the exact analytic formulation that allows one to describe the circulating current density and the gauge invariant phase increment ¿f across the junction. The main properties of ¿f and their influence on the critical current pattern Ic(B) are described quantitatively in terms of the loop''s width-to-radius ratio W/R and of the vortex position within the loop rv. It is shown that narrow loops (W/R<0.3) may be well described by the straight geometry limit. However, such approximation fails to predict a number of distinctive features captured by our formulation, such as the node lifting effect of the Ic(B) pattern in wide loops or the actual influence of a vortex pinned at different positions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Electromagnetic behaviour and thermal stability of a conduction-cooled, no-insulated 2G-HTS coil at intermediate temperatures

  • Cubero, A.
  • Núñez-Chico, A.B.
  • Navarro, R.
  • Angurel, L.A.
  • Martínez, E.
The electromagnetic and thermal properties of a double pancake coil made of second generation high temperature superconductor, 2G-HTS, have been studied. The coil was wound with no-insulation between turns (NI coil) and was later impregnated with epoxy resin and glued to a copper support plate. The coil was thermally anchored to the cryocooler cold finger and cooled by conduction. After several thermal cycles no degradation of its superconducting properties was observed. The coil was operated under high vacuum and high currents (up to 400 A in steady conditions) at different temperatures in the range between 5 K and 77 K, with special focus on the analysis above 30 K. The charge and discharge characteristics, and the experimentally measured and numerically estimated critical currents, have been studied. The different loss contributions during current ramp and the thermal contact conductance between different parts of the double pancake coil have been measured. The implications of these two factors on the thermal stability and the behaviour of the whole cryogenic system are discussed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High speed processing of NiFe2O4 spinel using a laser furnace

  • Özçelik, B.
  • Özçelik, S.
  • Amaveda, H.
  • Santos, H.
  • Borrell, C.J.
  • Sáez-Puche, R.
  • de la Fuente, G.F.
  • Angurel, L.A.
The Laser Furnace (LF) method has been applied to directionally solidify NiFe2O4 spinel disks from a mixture of Fe and Ni oxides in order to obtain uniform, dense targets for controlled synthesis of spinel nanoparticles via Laser Ablation. Application of a CO2 laser in Line Scan mode onto a sample with the desired stoichiometry, enabled melt processing above 1580 °C at its outer surface layer. This process was carried out inside a continuous roller furnace at a maximum volume temperature of 1000 °C. Such combination helps avoid excessive thermal stress, crack formation and catastrophic failure of these magnetic ceramic monoliths. Higher energy incubation values yield increased molten volumes and a thicker resolidified surface layer with a dense microstructure. Despite the high solidification rates imposed, NiFe2O4 spinel is the main phase obtained according to X-Ray Diffraction (XRD) and magnetization studies. LF processed samples exhibit a reduction of the coercive fields and an increase of the saturation magnetization values, evidence for soft ferromagnetism and characteristic of the magnetic behaviour associated with this spinel. This work demonstrates the convenience of the LF method for preparation of uniform, dense targets for Laser Ablation and other evaporation based techniques used in the fabrication of nanoparticles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Large enhancement of thermal conductance at ambient and cryogenic temperatures by laser remelting of plasma-sprayed Al2O3 coatings on Cu

  • Cubero, Á.
  • Martínez, E.
  • de la Fuente, G.F.
  • García Cano, I.
  • Dosta, S.
  • Angurel Lambán, L.A.
Joints of high thermal contact conductance and electrical insulation have been obtained by coating copper supports with thin alumina (Al2O3) layers (of 140–150 µm thickness). This has been achieved by a combination of plasma spraying process and the subsequent coating remelting by a near-Infrared (n-IR) laser. With a proper optimization of the laser processing conditions, it is possible to transform the metastable ¿-Al2O3 phase of the as-sprayed coatings to stable a-Al2O3, and to achieve denser alumina coatings. This results in a large enhancement of the thermal conductance of the joints, enabling their application as heat sinks at cryogenic and ambient temperatures. The process proposed in this work is scalable for the formation of alumina coatings on large metallic pieces of complex geometries. © 2021
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

IR laser line scanning treatments to improve levitation forces in MgTi0.06B2 bulk materials

  • Ozturk, K.
  • Aksoy, C.
  • Angurel, L.A.
  • Savaskan, B.
  • Martínez, E.
  • Badía-Majós, A.
  • de la Fuente, G.F.
  • Guner, B.
  • Dancer, C.E.J.
  • Celik, S.
Infrared (IR) laser-line scanning has been widely used to induce different surface microstructures in a broad range of materials. In this work, this laser configuration was applied on the surface of MgTi0.06B2 bulk samples in order to ascertain its effects on their superconducting properties, particularly on the magnetic levitation forces. The microstructural changes produced by this type of laser treatment were investigated by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). It was observed that the thermal treatment induced by the laser improves grain connectivity in a layer of material just below the irradiated surface, in agreement with the observed improvement in critical current density values, Jc, which were estimated from isothermal magnetic hysteresis loops. A significant increment of both vertical (Fz) and lateral (Fx) magnetic levitation forces was achieved. Numerical calculations were performed to understand the experimental behaviour and to clarify how an improvement of Jc near the surface can improve the magnetic levitation force of these materials. In addition, the same studies were carried out in similar bulk samples but with nano-sized silver particle additions of 3 and 6 wt %, in the outer ring of the bulk, observing also an improvement of the levitation forces, albeit less than in samples without Ag because of the better performance of the original samples after laser treatment. These results are relevant to those studying superconductor fabrication and material fabrication modelling, essential for the development of technological applications of superconductors, and are based on microstructure control via application of a recently developed laser-line scan method.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

MgB(2)cables made of thin wires manufactured by IMD process

  • Kovac, P
  • Kopera, L
  • Hain, M
  • Martinez, E
  • Kovac, J
  • Melisek, T
  • Berek, D
  • Husek, I
This paper presents the properties of cables made of thin MgB(2)wires with different sheaths manufactured by IMD process. Strong effect of the outer sheath on theJ(e)(B) performance was observed and the best properties were obtained for the strongest Cu sheath. It was found that the transversal and longitudinal cables uniformity affects the critical currents in MgB(2)wires made by IMD considerably. We have analyzed the quench dynamics in Rutherford cables with Al + 1.5%A(l2)O(3)sheath, when subjected to heat disturbances. Quench triggered in the strands in direct contact with the heater, observing important delays in quench development among strands. Low AC losses were measured for the extra-light Rutherford cable with Ti barrier and Al + 1.5%Al(2)O(3)sheath due to an increased barrier resisitivity and surface Al sheath oxidation, which reduces coupling current loss component effectivelly.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Improved copper–epoxy adhesion by laser micro- and nano-structuring of copper surface for thermal applications

  • Mora M.
  • Amaveda H.
  • Porta-Velilla L.
  • de la Fuente G.F.
  • Martínez E.
  • Angurel L.A.
The objective of this work is the enhancement of metal-to-metal bonding to provide high thermal conductivity together with electrical insulation, to be used as heat sinks at room and cryo-genic temperatures. High thermal conductive metal (copper) and epoxy resin (Stycast 2850FT) were used in this study, with the latter also providing the required electrical insulation. The copper surface was irradiated with laser to induce micro- and nano-patterned structures that result in an improvement of the adhesion between the epoxy and the copper. Thus, copper-to-copper bonding strength was characterized by means of mechanical tensile shear tests. The effect of the laser processing on the thermal conductivity properties of the Cu/epoxy/Cu joint at different temperatures, from 10 to 300 K, is also reported. Using adequate laser parameters, it is possible to obtain high bonding strength values limited by cohesive epoxy fracture, together with good thermal conductivity at ambient and cryogenic temperatures. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effects of laser-induced periodic surface structures on the superconducting properties of Niobium

  • Cubero, A.
  • Martínez, E.
  • Angurel, L. A.
  • de la Fuente, G. F.
  • Navarro, R.
  • Legall, H.
  • Krüger, J.
  • Bonse, J.
It is well known that the use of ultrashort (fs) pulsed lasers can induce the generation of (quasi-) periodic nanostructures (LIPSS, ripples) on the surface of many materials. Such nanostructures have also been observed in sample''s surfaces irradiated with UV lasers with a pulse duration of 300 ps. In this work, we compare the characteristics of these nanostructures on 1-mm and on 25-µm thick niobium sheets induced by 30 fs n-IR and 300 ps UV pulsed lasers. In addition to conventional continuous or burst mode processing configurations, two-dimensional laser beam and line scanning modes have been investigated in this work. The latter allows the processing of large areas with a more uniform distribution of nanostructures at the surface. The influence of the generated nanostructures on the superconducting properties of niobium has also been explored. For this aim, magnetic hysteresis loops have been measured at different cryogenic temperatures to analyse how these laser treatments affect the flux pinning behaviour and, in consequence, the superconductor''s critical current values. It was observed that laser treatments are able to modify the superconducting properties of niobium samples. © 2019 The Author(s)
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Laser-induced scanning transfer deposition of silver electrodes on glass surfaces: A green and scalable technology

  • Molina R.
  • Ertugrul M.
  • Larrea Á.
  • Navarro R.
  • Rico V.
  • Yubero F.
  • González-Elipe A.R.
  • Fuente G.F. de la
  • Angurel L.A.
A pulsed laser ablation backwriting technique with high repetitive rates is implemented for the fabrication of silver coatings on glass surfaces. This method enables geometrical constraint-free deposition of metallic coatings. These exhibit sufficiently low electrical resistance to be used as electrodes in dielectric barrier discharge (DBD) plasma elements. Ambient air deposition of metallic silver electrodes on standard glass slides is explored using a sub-ns UV laser source, combined with hybrid beam scanning methods. The green nature of the overall deposition process includes a preliminary irradiation scan to homogenise the target surface before the subsequent backwriting step. Metal transfer is achieved by combining two phenomena within a simple beam scanning process: LIRT (laser-induced reverse transfer) of silver from the target to the glass, with a partial and secondary LIFT (Laser-Induced Forward Transfer) of silver from the glass to the target. Appropriate selection of pulse energy and pulse repetition rates, beam scanning velocities and target motion enable the growth of sufficiently thick Ag deposits on glass with the required low electrical resistivity and nearly 2D constraint-free geometry. This method avoids the use of vacuum and liquids, resulting in a cheap, facile and green methodology for the deposition of silver electrodes onto transparent substrate surfaces.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Experimental and Numerical Investigation of Levitation Force Parameters of Novel Multisurface Halbach HTS-PMG Arrangement for Superconducting Maglev System

  • Ozturk K.
  • Badia-Majos A.
  • Abdioglu M.
  • Dilek D.B.
  • Gedikli H.
We have designed multisurface Halbach high temperature superconductor-permanent magnetic guideway (HTS-PMG) arrangements for magnetically levitated transportation (Maglev) and investigated the static force parameters in addition to the dynamic response characteristics. Three different Halbach HTS-PMG arrangements were used with multisurface (6 HTS, 4 HTS) and single surface (2 HTS) configurations and static and dynamic measurements were carried out in three different field cooling heights (FCHs). The bigger vertical loading capacity and wider loading gap were obtained with multisurface Halbach HTS-PMG arrangements. In addition, nearly four times bigger guidance force values of multisurface arrangements than that of single surface one indicates that the side HTSs in multisurface arrangements make a significant contribution to the guidance force and thus lateral movement stability of Maglev systems. Both the vertical and lateral dynamic stiffness values increased with decreasing FCH and it can be also said that the dynamic stiffness properties of Maglev systems can be enhanced especially in lateral direction by using the multisurface Halbach HTS-PMG arrangements. Understanding of these experimental observations is supported by dedicated theoretical modelling through a 2-D approximation of the system. We show that by using a single material parameter (the critical current density ${{\boldsymbol{J}}_{{\bf c}}}$) for the whole superconducting set, one may satisfactorily predict the complete series of experiments. The static and dynamic parameters obtained from this study and the results of dedicated theoretical modeling for single-surface and multisurface HTS-PMG arrangements are thought to be helpful for the researchers working on static and dynamic performances of HTS Maglev systems. © 2002-2011 IEEE.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Structure, magnetic, photocatalytic and blood compatibility studies of nickel nanoferrites prepared by laser ablation technique in distilled water

  • Özçelik, S.
  • Yalçin, B.
  • Arda, L.
  • Santos, H.
  • Sáez-Puche, R.
  • Angurel, L.A.
  • Fuente, G.F.D.L.
  • Özçelik, B.
The main objective of this study is to investigate the structural features, magnetic behaviour, photocatalytic properties and blood compatibility of NiFe2O4 nanoparticles (NPs) obtained by subnanosecond laser ablation in water. Structure and size distribution of NPs were studied using X-Ray Diffractometry (XRD) and Transmission Electron Microscopy (TEM). The photocatalytic properties of NPs were evaluated by photo-degradation of Methylene Blue (MeB) dye under ambient visible light illumination. Four different kinetic models were used to identify the photocatalytic degradation mechanism of NiFe2O4 nanoparticles and it was found that the pseudo-second-order model was the most suitable type to interpret the experimental kinetic data of MeB photodegradation. The hemocompatibility of NiFe2O4 nanoparticles was studied by hemolysis tests using human erythrocytes drawn from healthy volunteers. NiFe2O4 nanoparticles caused undesirable hemolysis ratios at 0.05, 1 and 5 mg/ml concentrations, while the biologically safe concentration of these nanoparticles was found to be below 0.01 mg/ml.