Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publicación Artículo científico (JournalArticle)

Robust anti-icing superhydrophobic aluminum alloy surfaces by grafting fluorocarbon molecular chains

  • Rico, V.
  • Mora, Julio
  • García, Paloma
  • Agüero, Alina
  • Borrás, A.
  • González Elipe, A.R.
  • López-Santos, C.
Infusion of low surface tension liquids in nanostructured surfaces is currently used to promote an anti-icing response, although the long term stability of these systems is often jeopardized by losses of the infused liquid. In this work, we propose an alternative to the infusion procedure to induce a more effective and long lasting anti-icing capacity. The method consists of a combination of surface nanostructuration with the chemical grafting of fluorocarbon molecules. Al6061 substrates have been subjected to laser roughening and further modified with a nanostructured Al2O3 thin film to achieve a dual roughness and porous surface state. These surfaces have been subjected to a grafting treatment with perfluorooctyltriethoxysilane (PFOTES) vapor or, for comparative purposes, infused with a low surface tension liquid. A comparative analysis of the wetting, water condensation and anti-icing properties of these two systems showed an outstandingly better performance for the grafted surfaces with respect to the infused ones. Grafted surfaces were markedly superhydrophobic and required higher water vapor pressures to induce condensation. When looking for their anti-icing capacity, they presented quite long freezing delay times for supercooled water droplets (i.e. almost four hours) and exhibited a notably low ice accretion in a wind tunnel test. The high aging resistance and durability of these grafted surfaces and the reproducibility of the results obtained when subjected to successive ice accretion cycles show that molecular grafting is an efficient anti-icing methodology that, in aggressive media, may outperform the classical infusion procedures. The role of the fluorocarbon chains anchored on the surface in inducing an anti-icing functionality is discussed., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors want to specially thank Airbus Group Innovations DE, Concordia Institute of Aerospace Design & Innovation of Concordia University and Department of Engineering Physics of Polytechnique Montreal for, respectively, the rain erosion, thermal cycling and sand erosion tests carried out within the frame of this project. The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00, PID2019-110430GB-C21 and CSIC 201860E050) for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US” (VI PPIT-US).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Metal films by laser ablation backwriting on glass

  • Angurel, Luis A.
  • Molina Mansilla, Ricardo
  • Rico, Víctor J.
  • Yubero, Francisco
  • González-Elipe, Agustín R.
  • Muñoz Rojas, David
  • Huerta, C. M. de la
  • Nguyen, V. H.
  • Fuente, Germán F. de la
Resumen del trabajo presentado a la Science and Applications of Thin Films, Conference & Exhibition; celebrada en Izmir (Turquia) del 17 al 21 de septiembre de 2018., The use of lasers to achieve transformations at interfaces, either on solids under air, controlled atmospheres or a diversity of liquid environments, is evolving at a fast pace and in-line with recent advances in photonic technologies. The singular properties of lasers, which provide a choice of emission parameters, such as emission wavelength, pulsed or cw mode and pulse width, together with the use of optomechanical means to scan in beam or line fashion, are ideal in order to trigger physico-chemical phenomena which are not available with alternative methods and are, at large, based on thermally activated processes. Recently developed methods in our Laboratories include those that are based, on the one hand, on strongly photothermal interactions; on the other, on mixed type interactions, where photothermal, photophysical and, in some cases, photochemical types may cohexist. In the former case, a solid may melt and, with the controled laser movement, directionally solidify into a material with controlled microstructure. In the latter case, an ablation process with extreme physical or chemical consequences may be triggered and be localised at the irradiated interface. A brief description of the phenomena behind laser-solid interactions will be presented, along with results obtained with the Laser Ablation Backwriting (LAB) method and applied to surface modification of glass. This has been recently developed in order to modify physico-chemical and functional properties of glass surfaces at large, based on this fully scaleable method. In particular, selective metallization of glass surfaces will be addressed in this talk., This research is partially supported by projects MAT2016-79866-R, ENE2017-83669-C4-1-R (Agencia Estatal de Investigación & Programa FEDER), PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FETOPEN 801464)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrophobicity, freezing delay, and morphology of laser-treated aluminum surfaces

  • Rico, Víctor J.
  • López-Santos, Carmen
  • Villagrá, Martín
  • Espinós, J.P.
  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Borrás, Ana
  • González-Elipe, Agustín R.
Until recently, superhydrophobicity was considered as a hint to predict surface icephobicity, an association of concepts that is by no means universal and that has been proven to depend on different experimental factors and material properties, including the actual morphology and chemical state of surfaces. This work presents a systematic study of the wetting and freezing properties of aluminum Al6061, a common material widely used in aviation, after being subjected to nanosecond pulsed IR laser treatments to modify its surface roughness and morphology. All treated samples, independent of their surface finishing state, presented initially an unstable hydrophilic wetting behavior that naturally evolved with time to reach hydrophobicity or even superhydrophobicity. To stabilize the surface state and to bestow the samples with a permanent and stable hydrophobic character, laser-treated surfaces were covered with a thin layer of CFx prepared by plasma-enhanced chemical vapor deposition. A systematic comparison between freezing delay (FD) and wetting properties of water droplets onto these plasma-/polymer-modified laser-treated surfaces that, under conditions where a heterogeneous nucleation mechanism prevails, surface morphology rather than the actual value of the surface roughness parameter the key feature for long FD times. In particular, it is found that surface morphologies rendering a Cassie–Baxter wetting regime longer FDs than those characterized by a Wenzel-like wetting state. It is that laser treatment, with or without additional coverage with thin CFx coatings, affects wetting and ice formation behaviors and might be an efficient procedure to mitigate icing problems on metal surfaces., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (201560E055 and MAT2016-79866-R and network MAT2015-69035-REDC) for financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Influence of crystallographic texture and external electromagnetic fields on sub-ns pulsed UV laser derived nanostructures

  • Porta-Velilla, L.
  • Cubero, A.
  • Castro, Miguel
  • Martínez Fernández, Elena
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Navarro, Rafael
Resumen del trabajo presentado al European Congress and Exhibition on Advanced Materials and Processes (EUROMAT), celebrado en Estocolmo (Suecia) del 1 al 5 de septiembre de 2019., [Introduction/Purpose]: Generation of Laser-induced Periodic Surface Structures (LIPSS) is a general phenomenon that has been observed in a broad range of materials and intensively studied since the commercial availability of ultra-short pulsed lasers. It has been observed that the morphology of LIPSS can be controlled by the selection of adequate laser processing parameters., [Methods]: In this work, we have analysed the generation of LIPSS in different metal surfaces using a sub-ns (300 ps) pulsed UV laser, with a laser-line scanning configuration. In addition to the laser parameters, different variables that can modify how LIPSS are generated, have been explored. EBSD studies have been used to determine the crystallographic direction of each grain at the surface of the material and how it modifies the characteristics of nanostructure generation. Experiments have also been performed under different electromagnetic fields during laser processing., [Results]: It has been observed that crystallographic orientation of grains has a significant influence on the generation of nanostructures. When prominent cones are generated, they appear only in some grains with a given orientation, for instance, (001) planes in stainless steel. In the case of ripples, period, size and orientation are also modified. For some configurations of external electromagnetic fields, the uniformity of the nanostructure can also be improved in extended areas., [Conclusions]: It is well established that nature and ordering of LIPSS nanostructures depend on the laser parameters, mainly irradiance and polarization, and on the material. In this work, it has been determined that for a given material, this order can be modified depending on the crystallographic orientation of each particular grain and using adequate external electromagnetic fields., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Metal surface nanostructures developed with sub-ns UV laser line scanning under different atmospheres

  • Fuente, Germán F. de la
  • Angurel, Luis A.
  • Cubero, A.
  • Porta-Velilla, L.
  • Castro, Miguel
  • Rojo, J. A.
  • Martínez Fernández, Elena
  • Navarro, Rafael
Resumen del trabajo presentado al International Symposium Fundamentals of Laser Assisted Micro- & Nanotechnologies (FLAMN), celebrado en San Petersburgo (Rusia) del 30 de junio al 4 de julio de 2019., Work financed by MAT2016-79866-R & ENE2017-83669-C4-1-R (MINECO-AEI-FEDER, UE), PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) and Aragón Government (Research Group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D organic nanofabrics: plasma-assisted synthesis and antifreezing behavior of superhydrophobic and lubricant-infused slippery surfaces

  • Alcaire, Maria
  • López-Santos, Carmen
  • Aparicio, Francisco J.
  • Sánchez-Valencia, J. R.
  • Obrero, José M.
  • Saghi, Zineb
  • Rico, Víctor J.
  • Fuente, Germán F. de la
  • González-Elipe, Agustín R.
  • Barranco, Ángel
  • Borrás, Ana
Herein, we present the development of supported organic nanofabrics formed by a conformal polymer-like interconnection of small-molecule organic nanowires and nanotrees. These organic nanostructures are fabricated by a combination of vacuum and plasma-assisted deposition techniques to generate step by step, single-crystalline organic nanowires forming one-dimensional building blocks, organic nanotrees applied as three-dimensional templates, and the polymer-like shell that produces the final fabric. The complete procedure is carried out at low temperatures and is compatible with an ample variety of substrates (polymers, metal, ceramics; either planar or in the form of meshes) yielding flexible and low solid-fraction three-dimensional nanostructures. The systematic investigation of this progressively complex organic nanomaterial delivers key clues relating their wetting, nonwetting, and anti-icing properties with their specific morphology and outer surface composition. Water contact angles higher than 150° are attainable as a function of the nanofabric shell thickness with outstanding freezing-delay times (FDT) longer than 2 h at −5 °C. The role of the extremely low roughness of the shell surface is settled as a critical feature for such an achievement. In addition, the characteristic interconnected microstructure of the nanofabrics is demonstrated as ideal for the fabrication of slippery liquid-infused porous surfaces (SLIPS). We present the straightforward deposition of the nanofabric on laser patterns and the knowledge of how this approach provides SLIPS with FDTs longer than 5 h at −5 °C and 1 h at −15 °C., We thank the AEI, MINECO (MAT2016-79866-R), and Consejerıa de Economia y Conocimiento de la Junta de Andalucia (US-1263142), the EU through cohesion fund and FEDER 20014-2020 programs and H2020 Phobic2Ice project(ref 690819) for financial support. This project has received funding from the EU-H2020 research and innovation program under the grant agreement No. 654360 (Id285) having benefitted from the access provided by CEA-Leti in Grenoble (France) within the framework of the NFFA-Europe Transnational Access Activity. F.J.A. and J.R.S.-V. acknowledge the Juan de la Cierva and Ramon y Cajal Programs, respectively. C.L.-S. and J.R.S.-V. thank the University of Seville through the VI PPIT-US., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Laser line scanning for large area surface microstructure control

  • Santos, H.
  • Angurel, Luis A.
  • Trujillo, F. J.
  • Muñoz Rojas, David
  • Masse, C.
  • Nguyen, V. H.
  • Bea, J. A.
  • Fuente, Germán F. de la
Resumen del póster presentado a la XXXVII Reunión Bienal de la Real Sociedad Española de Química, celebrada en Donostia-San Sebastián del 26 al 30 de mayo de 2019., Large-scale industrial materials must comply with crucial requirements beyond their technical specifications. The overall economy of any material system designed is a priority, leading to a complex equilibrium between costs and performance. Ultimate feasibility assessments rely on materials design efforts, particularly in processes exposed to extreme corrosive environments as well as those with high quality requirements in terms of interfacial defects in multilayer devices. In such systems surface engineering plays a key role, offering the means to maximize the life span of a certain material system. In parallel to the intrinsic cost savings derived in terms of maintenance, certain techniques allow an extreme control of the processing conditions, resulting in lower consumption of reactants, time and energy. This is the case of laser surface processing, particularly regarding laser line scanning (LLS). Such technique combines the transverse movement of a target with the fixed scanning linear movement of the laser spot along the axis perpendicular to the probe’s displacement. This technique has been applied to well-studied systems as Fe-Al protective coatings, rendering useful development paths to improve the alloying performance addressing subjects as: grain microstructure orientation, stoichiometric gradients smothering, segregation dispersion or interface defects density. The present work takes into account the above considerations, in an attempt to adapt this novel Laser Line Scanning method to process functional metal oxide coatings. With the help of standard simulation models, attempts to densify coated surfaces, as well as to control microstructure, will be described., The authors gratefully acknowledge the financial support from the Spanish Ministerio de Ciencia, Innovación y Universidades, Agencia Estatal de Investigación (AEI) and Fondo Europeo de Desarrollo Regional (FEDER) (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from EU (project SPRINT (EU H2020-FETOPEN/0426), PHOBIC2ICE (EU GA 690819)), and from the Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Generation of nanostructures in metallic surfaces using subnanosecond UV laser processing

  • Cubero, A.
  • Porta-Velilla, L.
  • Castro, Miguel
  • Angurel, Luis A.
  • Fuente, Germán F. de la
  • Martínez Fernández, Elena
  • Navarro, Rafael
Resumen del trabajo presentado a la International Conference on Condensed Matter and Materials Science (ICCMMS), celebrada en Adana (Turquia) del 14 al 19 de octubre de 2019., In this work we present the rich surface structure phenomenology that has been observed when the surface of different metals (Nb, Ni, steel) is irradiated with a subnanosecond (300 ps) UV laser, and how it affects some of their properties. The influence of different laser parameters, as the laser polarization direction, the pulse irradiance, laser scanning speed and the overlapping in the perpendicular direction, have been studied and a complete set of nanostructures have been defined. Laser treatments have been performed in air, but also in controlled atmospheres (Ar, N2) or with the surface immersed in liquids (Vaseline oil, water) observing that the generated nanostructures are different depending on the particular experimental conditions imposed. An important effort has been carried out in order to obtain homogeneous nanostructures over extended areas, using a new laser line scanning protocol. In these studies, it has been observed that not only the laser parameters affect the generated nanostructure, but some materials properties are also important. Combining laser treatments with EBSD studies it has been demonstrated that crystallography also plays an important role in the generated nanostructure, observing that the level of interaction of the laser with a particular grain has some correlation with its crystallographic order. It has ben also observed that, in depending on the properties of the materials, nanostructures can be modified by the application of external electromagnetic fields., The authors gratefully acknowledge the financial support from MINECO-AEI-FEDER (project ENE2017-83669-C4-1-R and MAT2016-79866-R), from PHOBIC2ICE (EU GA 690819) and SPRINT (EU H2020-FET-OPEN/0426) projects and from Gobierno de Aragón “Construyendo Europa desde Aragón” (research group T54_17R).