Pasar al contenido principal

TECNOLOGIA DE PLASMA PARA LA FABRICACION DE CELDAS SOLARES DE PEROVSKITA EFICIENTES Y DURADERAS A PRUEBA DE AGUA

PID2019-109603RA-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SEVILLA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

DIGITAL.INTA Repositorio Digital del Instituto Nacional de Técnica Aeroespacial
Publicación Artículo científico (JournalArticle)

Robust anti-icing superhydrophobic aluminum alloy surfaces by grafting fluorocarbon molecular chains

  • Rico, V.
  • Mora, Julio
  • García, Paloma
  • Agüero, Alina
  • Borrás, A.
  • González Elipe, A.R.
  • López-Santos, C.
Infusion of low surface tension liquids in nanostructured surfaces is currently used to promote an anti-icing response, although the long term stability of these systems is often jeopardized by losses of the infused liquid. In this work, we propose an alternative to the infusion procedure to induce a more effective and long lasting anti-icing capacity. The method consists of a combination of surface nanostructuration with the chemical grafting of fluorocarbon molecules. Al6061 substrates have been subjected to laser roughening and further modified with a nanostructured Al2O3 thin film to achieve a dual roughness and porous surface state. These surfaces have been subjected to a grafting treatment with perfluorooctyltriethoxysilane (PFOTES) vapor or, for comparative purposes, infused with a low surface tension liquid. A comparative analysis of the wetting, water condensation and anti-icing properties of these two systems showed an outstandingly better performance for the grafted surfaces with respect to the infused ones. Grafted surfaces were markedly superhydrophobic and required higher water vapor pressures to induce condensation. When looking for their anti-icing capacity, they presented quite long freezing delay times for supercooled water droplets (i.e. almost four hours) and exhibited a notably low ice accretion in a wind tunnel test. The high aging resistance and durability of these grafted surfaces and the reproducibility of the results obtained when subjected to successive ice accretion cycles show that molecular grafting is an efficient anti-icing methodology that, in aggressive media, may outperform the classical infusion procedures. The role of the fluorocarbon chains anchored on the surface in inducing an anti-icing functionality is discussed., This work has been carried out with the support of the EU project PHOBIC2ICE (ref 690819). The authors want to specially thank Airbus Group Innovations DE, Concordia Institute of Aerospace Design & Innovation of Concordia University and Department of Engineering Physics of Polytechnique Montreal for, respectively, the rain erosion, thermal cycling and sand erosion tests carried out within the frame of this project. The authors also thank the European Regional Development Funds program (EU-FEDER) and the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00, PID2019-110430GB-C21 and CSIC 201860E050) for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US” (VI PPIT-US).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Anisotropic Resistivity Surfaces Produced in ITO Films by Laser‐Induced Nanoscale Self‐organization

  • López-Santos, Carmen
  • Puerto, D.
  • Siegel, Jan
  • Macías-Montero, M.
  • Florian, Camilo
  • Gil-Rostra, J.
  • López-Flores, Víctor
  • Borrás, Ana
  • González-Elipe, Agustín R.
  • Solís Céspedes, Javier
11 pags., 8 figs., 2 tabs., Highly anisotropic resistivity surfaces are produced in indium tin oxide (ITO) films by nanoscale self‐organization upon irradiation with a fs‐laser beam operating at 1030 nm. Anisotropy is caused by the formation of laser‐induced periodic surface structures (LIPSS) extended over cm‐sized regions. Two types of optimized structures are observed. At high fluence, nearly complete ablation at the valleys of the LIPSS and strong ablation at their ridges lead to an insulating structure in the direction transverse to the LIPSS and conductive in the longitudinal one. A strong diminution of In content in the remaining material is then observed, leading to a longitudinal resistivity ρL ≈ 1.0 Ω·cm. At a lower fluence, the material at the LIPSS ridges remains essentially unmodified while partial ablation is observed at the valleys. The structures show a longitudinal conductivity two times higher than the transverse one, and a resistivity similar to that of the pristine ITO film (ρ ≈ 5 × 10−4 Ω·cm). A thorough characterization of these transparent structures is presented and discussed. The compositional changes induced as laser pulses accumulate, condition the LIPSS evolution and thus the result of the structuring process. Strategies to further improve the achieved anisotropic resistivity results are also provided., This research was funded by the Spanish Ministry of Science, Innovation and Universities, the Spanish Research Agency (AEI, Ministry of Research and Innovation), and the European Regional Development Fund (ERDF) (grant numbers TEC2017-82464-R, PID2019-109603RA-I00, and PID2019- 110430GB-C21), the “Consejería de Economía y Conocimiento de la Junta de Andalucía” (PAIDI-2020 projects P18-RT-3480 and -6079). The authors also acknowledge the Consejo Superior de Investigaciones Científicas for the “Intramural Project” (201850E057). C.L.-S. acknowledges the funding of the University of Seville through the “VI Plan Propio de Investigación y Transferencia de la US” (VI PPIT-US). M.M.-M. acknowledges the postdoctoral Juan de la Cierva Incorporación grant (IJCI-2017-33317)) of the same ministry. C.F. thanks the support from the European Commission through the Marie Curie Global Fellowship grant number 844977. V.L.-F. thanks the support from European Commission/Junta de Andalucía Talent-Hub Program. The authors thank the Research, Technology, and Innovation Center of the University of Seville (CITIUS) and Microscopy Service of the University Pablo de Olavide (Seville) for access to several material characterization facilities, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Comparative analysis of the germination of barley seeds subjected to drying, hydrogen peroxide, or oxidative air plasma treatments

  • Perea-Brenes, Álvaro
  • Gómez-Ramírez, Ana
  • López-Santos, Carmen
  • Oliva-Ramírez, Manuel
  • Molina Mansilla, Ricardo
  • Cotrino, José
  • García Fernández, José Luis
  • Cantos, Manuel
  • González-Elipe, Agustín R.
17 páginas.- 10 figura.- 1 tablas.- 63 referencias, Acceleration in germination time by 12-24 h for barley seeds treated with atmospheric air plasmas may have a significant economic impact on malting processes. In this study, the increase in germination rate and decrease in contamination level upon plasma treatment could not be directly correlated with any significant increase in the water uptake capacity, except for seeds exposed to mild drying treatment. A variety of germination essays have been carried out with seeds impregnated with an abscisic acid solution, a retarding factor of germination, treated with a peroxide solution, and/or subjected to the plasma and drying treatments. Results suggest that plasma and hydrogen peroxide treatments induce the formation of reactive oxygen and nitrogen species that affects the abscisic acid factor and accelerate the germination rate. ABA factorbarley germinationhydrogen peroxide treatmentplasma surface oxidation, the financial support of the Consejeria de Economia, Conocimiento, Empresas y Universidad de la Junta de Andalucia through first the project US-1381045, and second the US-1380977, as well as the EU through cohesion fund and FEDER 2014-2020 programs for financial support. We also thank the AEI-MICINN (PID2019-110430GB-C21, PID2019-109603RA-10, and PID2020-114270RA-I00 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF (FEDER) A way of making Europe," by the "European Union." The contribution of Arquimea Research for the realization of parts of this study is also acknowledged. We thank Intermalta S.A. for the seeds supply. This article frames within COST Action PIAgri-CA19110, supported by COST (European Cooperation in Science and Technology), . Carmen Lopez-Santos thanks the support of the University of Seville through the VI PPIT-US and the Ramon y Cajal Spanish National programs funded by MCIN/AEI/10.13039/501100011033. Manuel Oliva-Ramirez thanks a contract grant within the Paidi 2020 of the EU social fund-University of Seville. We also thank effusively the support of Dr. Pedro E. Sanchez-Jimenez during the thermogravimetric microbalance experiments., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Germination and First Stages of Growth in Drought, Salinity, and Cold Stress Conditions of Plasma-Treated Barley Seeds

  • Perea-Brenes, Álvaro
  • García Fernández, José Luis
  • Cantos, Manuel
  • Cotrino, José
  • González-Elipe, Agustín R.
  • Gómez-Ramírez, Ana
  • López-Santos, Carmen
Numerous works have demonstrated that cold plasma treatments constitute an effective procedure to accelerate seed germination under nonstress conditions. Evidence also exists about a positive effect of plasmas for germination under environmental stress conditions. For barley seeds, this work studies the influence of cold plasma treatments on the germination rate and initial stages of plant growth in common stress environments, such as drought, salinity, and low-temperature conditions. As a general result, it has been found that the germination rate was higher for plasma-treated than for untreated seeds. Plasma also induced favorable changes in plant and radicle dimensions, which depended on the environment. The obtained results demonstrate that plasma affects the biochemical metabolic chains of seeds and plants, resulting in changes in the concentration of biochemical growing factors, a faster germination, and an initially more robust plant growth, even under stress conditions. These changes in phenotype are accompanied by differences in the concentration of biomarkers such as photosynthetic pigments (chlorophylls a and b and carotenoids), reactive oxygen species, and, particularly, the amino acid proline in the leaves of young plants, with changes that depend on environmental conditions and the application of a plasma treatment. This supports the idea that, rather than an increase in seed water imbibition capacity, there are clear beneficial effects on seedling of plasma treatments., We acknowledge the financial support of the Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía through first the project US-1381045 and second the US-1380977 as well as the EU through a cohesion fund and FEDER 2014–2020 programs. We also thank the AEI-MICINN (PID2019-110430GB-C21, PID2019-109603RA-I00, PID2020-114270RA-I00, TED2021-130124A-I00, and TED2021-130916B-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe” and “NextGenerationEU”/PRTR” by the European Union; AEI. We thank Intermalta S.A. for the seeds supply. This article frames within COST Action PIAgri-CA19110, supported by COST (European Cooperation in Science and Technology), www.cost.eu. C.L.-S. thanks the support of the University of Seville through the VI PPIT-US and the Ramon y Cajal Spanish National programs funded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A holistic solution to icing by acoustic waves: de-icing, active anti-icing, sensing with piezoelectric crystals, and synergy with thin film passive anti-icing solutions

  • Moral, Jaime del
  • Montes, Laura
  • Rico, Víctor J.
  • López-Santos, Carmen
  • Jacob, Stefan
  • Oliva-Ramírez, Manuel
  • Gil-Rostra, J.
  • Fakhfouri, Armaghan
  • Pandey, Shilpi
  • Gonzalez, Miguel
  • Mora, Julio
  • Garcia-Gallego, Paloma
  • Ibanez-Ibanez, Pablo F.
  • Rodriguez-Valverde, Miguel A
  • Winkler, Andreas
  • Borrás, Ana
  • González-Elipe, Agustín R.
20 pages including Supporting Information; 8 figures in the main text, Icing has become a hot topic both in academia and in the industry given its implications in transport, wind turbines, photovoltaics, and telecommunications. Recently proposed de-icing solutions involving the propagation of acoustic waves (AWs) at suitable substrates may open the path for a sustainable alternative to standard de-icing or anti-icing procedures. Herein, the fundamental interactions are unraveled that contribute to the de-icing and/or hinder the icing on AW-activated substrates. The response toward icing of a reliable model system consisting of a piezoelectric plate activated by extended electrodes is characterized at a laboratory scale and in an icing wind tunnel under realistic conditions. Experiments show that surface modification with anti-icing functionalities provides a synergistic response when activated with AWs. A thoughtful analysis of the resonance frequency dependence on experimental variables such as temperature, ice formation, or wind velocity demonstrates the application of AW devices for real-time monitoring of icing processes., J.D.M. and L.M. contributed equally to this work. The authors thank projects PID2019-110430GB-C21, PID2019-109603RA-I00, and PID2020-112620GB-I00 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF (FEDER) A way of making Europe", by the "European Union". The project leading to this article has received funding from the EU H2020 program under grant agreement 899352 (FETOPEN-01-2018-2019-2020 - SOUNDofICE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exalted dual-scale surface roughening in laser ablated aluminum capped with a transparent thin film: Wetting and anti-icing behavior

  • Ghemras, Ismail
  • Montes, Laura
  • López-Santos, Carmen
  • González-Elipe, Agustín R.
  • Rico, Víctor J.
Near infrared laser ablation of metals, specifically aluminum, has been systematically applied to generate surface roughness. Very high laser fluences may even lead to a so called “explosive” ablation regime where roughness becomes dramatically enhanced. In the present work we have developed an alternative methodology that, utilizing milder laser irradiation conditions (i.e. laser fluences from 0.37 to 0.72 J/cm2), renders aluminum surfaces with a dual-scale roughness character and Sp parameter values twice or even trice the value found in reference samples. This has been possible for aluminum substrates coated with a highly transparent aluminum oxynitride capping layer. The resulting surfaces, consisting of very rough partially oxidized aluminum with negligible amounts of nitrogen species, resulted highly hydrophobic and depicted long icing delay times as required for anti-icing applications. A correlation has been found between the wetting and anti-icing behaviors, the use of a capping layer and the laser irradiation conditions. To account for this exalted roughening phenomenon, we propose that the transparent capping layer confines the laser energy within the aluminum shallow zones, delays the formation of the plasma plume and produces an enhancement in the aluminum ablation, even at relatively low laser fluences., This work was supported by the General Directorate for Scientific Research and Technological Development (DGRSDT) of the High School Educational and Scientific Research Ministry (MESRS) of Algeria [Grant: P.N.E (2018-2019)]. Also, the project leading to this article has received funding from the EU H2020 program under grant agreement 899352 (FETOPEN-01-2018-2019-2020 - SOUNDofICE). We also thank the AEI-MICINN (PID2019-110430GB-C21, PID2020-112620GBI00 and PID2019-109603RA-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe,” by the “European Union”. We acknowledge the financial support of the Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía through the project US-1381045 as well as the EU through cohesion fund and FEDER 2014–2020 programs for financial support. Carmen López-Santos thanks the support of the University of Seville through the VI PPIT-US and the Ramón y Cajal Spanish National programs funded by MCIN/AEI/10.13039/501100011033, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Setting a comprehensive strategy to face the runback icing phenomena

  • Mora, J.
  • López García, Paloma
  • Carreño, F.
  • González, M.
  • Gutiérrez, M.
  • Montes, L.
  • Gavira, V. R.
  • López-Santos, Carmen
  • Vicente, A.
  • Rivero, P.
  • Rodríguez, R.
  • Larumbe, S.
  • Acosta, C.
  • Ibáñez-Ibáñez, P.
  • Corozzi, A.
  • Raimondo, M,
  • Kozera, R,
  • Przybyszewski, B,
  • González-Elipe, Agustín R.
  • Borrás, Ana
  • Redondo, F,
  • Agüero, A,
The development of anti-icing robust surfaces is a hot topic nowadays and particularly crucial in the aeronautics or wind energy sectors as ice accretion can compromise safety and power generation efficiency. However, the current performance of most anti-icing strategies has been proven insufficient for such demanding applications, particularly in large unprotected zones, which located downstream from thermally protected areas, may undergo secondary icing. Herein, a new testing methodology is proposed to evaluate accretion mechanisms and secondary icing phenomena through, respectively, direct impact and running-wet processes and systematically applied to anti-icing materials including commercial solutions and the latest trends in the state-of-the-art. Five categories of materials (hard, elastomeric, polymeric matrix, SLIPS and superhydrophobic) with up to fifteen formulations have been tested. This Round-Robin approach provides a deeper understanding of anti-icing mechanisms revealing the strengths and weaknesses of each material. The conclusion is that there is no single passive solution for anti-ice protection. Thus, to effectively protect a given real component, different tailored materials fitted for each particular zone of the system are required. For this selection, shape analysis of such a component and the impact characteristics of water droplets under real conditions are needed as schematically illustrated for aeronautic turbines., The project leading to this article has received funding from the EU H2020 program under grant agreement 899352 (FETOPEN-01-2018-2019-2020 - SOUNDofICE). The authors also thank the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00 and PID2019-110430GB-C21) funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe”, to RTI2018-096262-B-C44–MAITAI, Multidisciplinary Approach for the Implementation of New Technologies to prevent Accretion of Ice on aircraft, funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia, Innovación y Universidades—Retos) and CSIC 202160E002-217538, for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US”(VI PPIT-US) and the Ramon y Cajal Grant program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly Stable Photoluminescence in Vacuum-Processed Halide Perovskite Core–Shell 1D Nanostructures

  • Castillo-Seoane, Javier
  • Contreras-Bernal, Lidia
  • Rojas, T. Cristina
  • Espinós, J.P.
  • Castro-Méndez, Andrés Felipe
  • Correa-Baena, Juan Pablo.
  • Barranco, Ángel
  • Borrás, Ana
  • Sánchez-Valencia, J. R.
Hybrid organometal halide perovskites (HP) present exceptional optoelectronic properties, but their poor long-term stability is a major bottleneck for their commercialization. Herein, a solvent-free approach to growing single-crystal organic nanowires (ONW) is presented, along with nanoporous metal oxide scaffolds and HP, to form a core@multishell architecture. The synthesis is carried out under mild vacuum conditions employing thermal evaporation for the metal-free phthalocyanine (H2Pc) nanowires, which are the core, plasma-enhanced chemical vapor deposition (PECVD) for the TiO2 shell, and co-evaporation of lead iodide (PbI2) and methylammonium iodide (CH3NH3I/MAI) for the CH3NH3PbI3 (MAPbI3/MAPI) perovskite shell. A detailed characterization of the nanostructures by electron microscopy, (S)-TEM, and X-ray diffraction, XRD, is presented, revealing a different crystallization of the HP depending on the template: while the growth on H2Pc nanowires induces the typical MAPI tetragonal structure, a low-dimensional phase (LDP) is observed on the 1D-TiO2 nanotubes. Such a combination yields an unprecedentedly stable photoluminescence emission over 20 h and over 300 h after encapsulation in polymethyl methacrylate (PMMA) under different atmospheres including N2, air, and high moisture levels. Moreover, the unique 1D morphology of the system, together with the high refractive index, allows for a strong waveguiding effect along the HP nanowire length., The authors thank the projects PID2022-143120OB-I00, PID2019-109603RA-I00, TED2021-130916B-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe, Fondos Nextgeneration EU and Plan de Recuperación, Transformación y Resiliencia”. The authors also want to thank CSIC for its financial support through the Intramural Project PIE 202260I156 and Interdisciplinary Thematic Platform (PTI) Transición Energética Sostenible (PTI-TRANSENER+). The project leading to this article has received funding from the EU H2020 program under grant agreement 851929 (ERC Starting Grant 3DScavengers). The authors also thank the group of Prof. Heben at the University of Toledo (US) for their assistance in understanding the crystalline low-dimensional phase., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Multidimensional nanoarchitectures for improved indoor light harvesting in dye-sensitized solar cells

  • Castillo-Seoane, Javier
  • Contreras-Bernal, Lidia
  • Riquelme, Antonio J.
  • Fauvel, Samuel
  • Kervella, Yann
  • Gil-Rostra, Jorge
  • Lozano, Gabriel
  • Barranco, Ángel
  • Demadrille, Renaud
  • Sánchez-Valencia, Juan R.
  • Borrás, Ana
Dye Sensitized Solar Cells (DSSCs) have recently gained renewed interest for their potential in indoor light harvesting and powering wireless devices. However, to fully exploit their potential, crucial aspects require further attention, in particular, the improvement of spectral compatibility and low-light harvesting mechanisms, as well as the development of efficient photoanodes through high-yield scalable methods. In this article, we propose the use of nanocomposite photoanodes integrating mesoporous TiO2 nanoparticles, ITO nanotubes (NT), and anatase TiO2 shells (ITO@TiO2 NT) prepared by step-by-step method relying on mild temperature conditions and avoiding toxic precursors. These photoanodes outperform previous attempts to implement low-dimensional ITO and ITO@TiO2 nanowires and nanotubes for outdoor light conversion, demonstrating a power conversion efficiency under low artificial light intensity of 24 % for at 0.014 mW cm−2, a 166 % increase compared to the conventional architectures. Advanced microstructural, optical, and electrochemical characterizations have revealed that the strong scattering effect of the light in the visible range coupled with enhanced charge collection at low-intensity illumination are the essential mechanisms responsible for such enhanced energy conversion. Remarkably, our devices retain up to 90 % of the normal incidence efficiency even under glancing illumination, while conventional reference devices retain only 30 %., We thank the projects PID2019-109603RA-I00, TED2021-130916B-I00, PID2019-110430 GB-C21, and PID2022-143120OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe, Fondos NextgenerationEU and Plan de Recuperación, Transformación y Resiliencia”. LCB acknowledges the French embassy in Spain for the grant “123892U” within framework of the proposal scientific call 2022 “Becas doctorales y postdoctorales”. Thanks to C.M.D Felipe II, particularly María Inmaculada Carmona Rivera, for providing some tools for preparing counter-electrodes. The authors also thank CSIC for its financial support through the Interdisciplinary Thematic Platform (PTI) Transición Energética Sostenible (PTI-TRANSENER+). R.D. acknowledges the European Research Council (ERC) for funding. This work was funded under the European Union's Horizon 2020 research and innovation programme (grant agreement number 832606; project PISCO). The project leading to this article has received funding from the EU H2020 program under grant agreement 851929 (ERC Starting Grant 3DScavengers)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mechanically Switchable Wetting Petal Effect in Self-Patterned Nanocolumnar Films on Poly(dimethylsiloxane)

  • Parra-Barranco, Julian
  • López-Santos, Carmen
  • Sánchez-Valencia, Juan Ramón
  • Borrás, Ana
  • González-Elipe, Agustín R.
  • Barranco, Ángel
Switchable mechanically induced changes in the wetting behavior of surfaces are of paramount importance for advanced microfluidic, self-cleaning and biomedical applications. In this work we show that the well-known polydimethylsiloxane (PDMS) elastomer develops self-patterning when it is coated with nanostructured TiO2 films prepared by physical vapor deposition at glancing angles and subsequently subjected to a mechanical deformation. Thus, unlike the disordered wrinkled surfaces typically created by deformation of the bare elastomer, well-ordered and aligned micro-scaled grooves form on TiO2/PDMS after the first post-deposition bending or stretching event. These regularly patterned surfaces can be reversibly modified by mechanical deformation, thereby inducing a switchable and reversible wetting petal effect and the sliding of liquid droplets. When performed in a dynamic way, this mechanical actuation produces a unique capacity of liquid droplets (water and diiodomethane) transport and tweezing, this latter through their selective capture and release depending on their volume and chemical characteristics. Scanning electron and atomic force microscopy studies of the strained samples showed that a dual-scale roughness, a parallel alignment of patterned grooves and their reversible widening upon deformation, are critical factors controlling this singular sliding behavior and the possibility to tailor their response by the appropriate manufacturing of surface structures., The projects leading to this article received funding from the EU H2020 program under the grant agreement 899352 (FETOPEN-01-2018-2019-2020—SOUNDofICE), the AEI-MICINN (PID2019-110430GB-C21 and PID2019-109603RA-I0, MAT2013-40852-R, MAT2013- 42900-P and MINECO-CSIC 201560E055) and the Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía (PAIDI-2020 through projects ref. AT17-6079, P18-RT-3480)., The authors thank the AEI-MICINN (PID2019-110430GB-C21 and PID2019-109603RA-I0, MAT2013-40852-R, MAT2013- 42900-P and MINECO-CSIC 201560E055), the Consejería de Economía, Conocimiento, Empresas y Universidad de la Junta de Andalucía (PAIDI-2020 through projects ref. AT17-6079, P18-RT-3480, US-1263142 and US-1381045) and the EU through cohesion fund and FEDER 2014–2020 and the EU H2020 program under the grant agreement 899352 (FETOPEN-01-2018-2019-2020—SOUNDofICE). C.L.-S. and J.R.S.-V. thank the University of Seville through the VI PPIT-US program. J.R.S.-V. thanks the Ramon y Cajal Spanish National program., Peer reviewed
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Setting a comprehensive strategy to face the runback icing phenomena

  • Mora, Julio
  • García, Paloma
  • Carreño, Francisco
  • González, Miguel
  • Gutiérrez, Marcos
  • Montes, Laura
  • Rico, Victor J.
  • López-Santos, Carmen
  • Vicente Gómara, Adrián
  • Rivero Fuente, Pedro J.
  • Rodríguez Trías, Rafael
  • Larumbe Abuin, Silvia
  • Acosta, Carolina
  • Ibáñez-Ibáñez, Pablo
  • Corozzi, Alessandro.
  • Raimondo, Mariarosa
  • Kozera, Rafal
  • Przybyszewski, Bartlomiej
  • González-Elipe, Agustín R.
  • Borrás, Ana
  • Redondo, Francisco
  • Agüero, Alina
The development of anti-icing robust surfaces is a hot topic nowadays and particularly crucial in the aeronautics or wind energy sectors as ice accretion can compromise safety and power generation efficiency. However, the current performance of most anti-icing strategies has been proven insufficient for such demanding applications, particularly in large unprotected zones, which located downstream from thermally protected areas, may undergo secondary icing. Herein, a new testing methodology is proposed to evaluate accretion mechanisms and secondary icing phenomena through, respectively, direct impact and running-wet processes and systematically applied to anti-icing materials including commercial solutions and the latest trends in the state-of-the-art. Five categories of materials (hard, elastomeric, polymeric matrix, SLIPS and superhydrophobic) with up to fifteen formulations have been tested. This Round-Robin approach provides a deeper understanding of anti-icing mechanisms revealing the strengths and weaknesses of each material. The conclusion is that there is no single passive solution for anti-ice protection. Thus, to effectively protect a given real component, different tailored materials fitted for each particular zone of the system are required. For this selection, shape analysis of such a component and the impact characteristics of water droplets under real conditions are needed as schematically illustrated for aeronautic turbines., The project leading to this article has received funding from the EU H2020 program under grant agreement 899352 (FETOPEN-01-2018-2019-2020 - SOUNDofICE). The authors also thank the MINECO-AEI (MAT2016-79866-R, PID2019-109603RA-I00 and PID2019-110430GB-C21) funded by MCIN/AEI/10.13039/501100011033 and by “ERDF (FEDER) A way of making Europe”, to RTI2018-096262-B-C44–MAITAI, Multidisciplinary Approach for the Implementation of New Technologies to prevent Accretion of Ice on aircraft, funded by MCIN/AEI/10.13039/501100011033 (Ministerio de Ciencia, Innovación y Universidades—Retos) and CSIC 202160E002-217538, for financial support. CLS thanks the University of Seville through the VI “Plan Propio de Investigación y Transferencia de la US”(VI PPIT-US) and the Ramon y Cajal Grant program.