Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Clay honeycomb monoliths for the simultaneous retention of lead and cadmium in water

  • Ahrouch, M.
  • Gatica Casas, José Manuel
  • Draoui, K.
  • Bellido Milla, Dolores
  • Vidal Muñoz, Hilario
Natural illite-smectite and stevensite Moroccan clays were used for the simultaneous removal of lead and cadmium from aqueous medium. The clays were employed in raw state and extruded as honeycomb monoliths form without any additives, which confirms the novelty of this approach in water treatment. The experiments were done in batch conditions with continuous stirring and using a recirculated flow, respectively. In addition to a characterization of the clays by XRF, XRD, TGA, laser granulometry, N2 physisorption, FTIR spectroscopy, SEM-EDS and evaluation of the cation exchange capacity, special attention was paid to the influence on the co-adsorption of variables such as adsorbent dosage, contact time and initial concentration of Cd2+ and Pb2+. Pseudo-second order kinetics and good fitting to Redlich-Peterson model for both heavy metals were found. Our results also suggest that Pb2+ and Cd2+ uptake is controlled by chemisorption with predominance of Langmuir characteristics. No significant depletion of the metals retention attributable to competition was observed, particularly for the stevensite (maximum retention capacity of 1.2 mg Pb2+/g and 4.6 mg Cd2+/g) that showed higher specific surface area. For both clays, cadmium ions adsorption was relatively favoured in the bimetallic solution, and the honeycombs kept the powders performance. Honeycomb monoliths as a compact adsorbent offer a promising way of water treatment thanks to their stability and easy incorporation into dynamic processes avoiding the issues of pressure drop under wastewater circulation. (c) 2022 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Honeycomb monolithic design to enhance the performance of Ni-based catalysts for dry reforming of methane

  • Agueniou, Fazia
  • Vidal Muñoz, Hilario
  • Yeste Siguenza, María del Pilar
  • Hernández Garrido, Juan Carlos
  • Cauqui López, Miguel Ángel
  • Rodríguez-Izquierdo Gil, José María
  • Calvino Gámez, José Juan
  • Gatica Casas, José Manuel
Supported Ni catalysts (4.5 wt%) using a Ce-Zr oxide (18/82 molar ratio and a ceria-rich surface) depicting advanced redox properties, were deposited by washcoating over cordierite honeycombs (230 and 400 cpsi). FIB-STEM unveiled nanostructure details otherwise undistinguishable by conventional techniques. The catalytic performance was evaluated in the dry reforming of methane at 700-900 ºC, using a CH4:CO2 1:1 feedstock, and exploring high Weight Hourly Space Velocity (115-346 L g-1 h-1). The structured catalysts exhibited better performance than the corresponding powders, reaching values close to thermodynamic limits for both reactants conversion and H2/CO ratio, from 750 ºC, and no deactivation was observed in prolonged experiments (24-48 hours). This was related to both the high catalyst efficiency after being deposited with low loading on the cordierite and the intrinsic advantages of the monolithic reactor, like preventing from the kinetic control that operates in powdered samples under high WHSV or limiting the deactivation., The authors thank the financial support by the Ministry of Economy and Competitiveness of Spain/FEDER Program of the EU (Project MAT2017-87579-R), and the Junta de Andalucía (Groups FQM-110 and FQM-334). We also acknowledge the Cadiz University SC-ICyT for using its facilities for the ICP-AES, XRD, XRF and SEM-EDX measurements, and the Seville University CITIUS for the FIB-(S)TEM studies., Artículo científico de 10 pgs. Publicado el 1 de enero de 2022 y cumplidos dos años desde dicha fecha, se puede incluir el fichero con la versión remitida a publicar en el repositorio institucional RODIN.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Methanation of carbon dioxide over ceria-praseodymia promoted Ni-alumina catalysts. Influence of metal loading, promoter composition and alumina modifier

  • Lechkar, Ali
  • Barroso Bogeat, Adrián
  • Blanco Montilla, Ginesa
  • Pintado Caña, José María
  • Soussi el Begrani, Mohamed
Two series of ceria-praseodymia promoted Ni-alumina catalysts were prepared from two different commercial modified alumina supports (3.5 wt% SiO2-Al2O3 and 4.0 wt% La2O3-Al2O3) by the incipient wetness impregnation method in two successive steps. The resulting materials were characterized in terms of their physico-chemical properties by means of N2 physical adsorption at −196 °C, powder X-ray diffraction (XRD) and temperature programmed reduction with H2 (H2-TPR). Furthermore, the as-prepared catalysts were tested for the CO2 methanation reaction in a fixed-bed reactor at atmospheric pressure, gas hourly space velocity (GHSV) of 72,000 cm3·(h·gcat)−1 and CO2/H2 molar ratio of 1/4 over the temperature range from 25 up to 850 °C. The influence of the nominal Ni loading (3, 5 and 10 wt%), molar composition of the Ce/Pr mixed oxide promoter (80/20 and 60/40), and alumina modifier (silica and lanthana) on the catalytic performance was carefully analyzed. Among these three composition parameters, the alumina dopant and especially the Ni content appear to have by far a much more pronounced effect on both the CO2 conversion and CH4 selectivity as compared to the Ce/Pr mixed oxide composition. Specifically, from the catalytic tests the sample containing a 10 wt% Ni loading, a Ce/Pr mixed oxide promoter of 80/20 molar composition, and silica as modifier provides the highest catalytic activity in terms of CO2 conversion and CH4 selectivity. Such behaviour has been ascribed to a complex interplay between several factors, mainly the larger fraction of catalytically active β-type NiO species and the lesser concentration of strong basic sites on the catalyst surface, as well as the electron back donation effect from the surface Ni atoms to the adsorbed COx species, which favours the C–O bond cleavage (i.e., the rate-determining step of the methanation reaction). These findings are expected to be very helpful in order to rationally design synthetic strategies that allow developing highly active and low cost Ni-based catalysts for the CO2 methanation reaction.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Valorization of Recycled Honeycombs from Exhausted TWCs by Means of Their Use as a Support of MnOx Catalysts for Acetone Combustion

  • De los Santos, Carolina
  • Gatica Casas, José Manuel
  • Castiglioni, Jorge
  • Vidal Muñoz, Hilario
Exhausted TWCs subjected to chemical/thermal treatments were used as a support of MnOx catalysts for the total combustion of acetone. The so-prepared new devices were characterized by using adherence tests, elemental and thermal analyses, XRD, N2 physisorption, and SEM-EDS. Incorporation of only 2.6 wt.% of the active phase (Mn2O3 and Mn3O4) to the recycled honeycomb considerably improved the catalytic response, achieving at 250 °C a 60% increase in acetone conversion with respect to the spent autocatalyst. The following procedure is proposed as a simple way to provide the TWC devoid of noble metals a second life in the VOCs’ oxidation field., 9 páginas
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

The Role of Surface {010} Facets in Improving the NOx Depolluting Activity of TiO2 and Its Application on Building Materials

  • Luna Aguilera, Manuel Jesús
  • Cruces, J.L.
  • Gatica Casas, José Manuel
  • Cruceira Fernández de Arjona, Álvaro
  • Cifredo Chacón, Gustavo Aurelio
  • Vidal Muñoz, Hilario
  • Mosquera Díaz, María Jesús
Air pollution, a major health concern, necessitates innovative solutions such as TiO2-based photocatalytic building materials to combat its harmful effects. This study focuses on developing high-performance TiO2 photocatalysts for NOx removal in building applications, aiming to overcome the limitations of commercial TiO2. These photocatalysts were synthesized via a hydrothermal method, with parameters such as synthesis time and post-treatment investigated to optimize their properties. Hydrothermal synthesis yielded TiO2 nanoparticles with reduced aggregation and a high proportion of elongated particles with exposed {010} facets. This resulted in significantly enhanced photocatalytic activity compared to commercial P25 in methylene blue degradation and NOx depollution. Subsequently, the optimized hydrothermal TiO2 was successfully integrated into a silica sol–gel coating for application on building materials. The coated concrete demonstrated significantly higher NOx removal efficiency and lower NO2 release, achieving a 1.7-fold improvement in overall NOx removal and significantly higher depolluting effectiveness compared to its P25 counterpart. These findings highlight the potential of hydrothermally synthesized TiO2 with controlled morphology for the development of high-performance, environmentally friendly building materials with enhanced air purification capabilities.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Novel combination of 3D-printing and electrochemical deposition to design and prepare metallic honeycomb supported catalysts for dry reforming

  • Bazta, Otman
  • Botana Pedemonte, Francisco Javier
  • Calvino Gámez, José Juan
  • Cauqui López, Miguel Ángel
  • Gatica Casas, José Manuel
  • Vidal Muñoz, Hilario
  • González Rovira, Leandro
  • López Castro, Juan De Dios
  • Yeste Siguenza, María del Pilar
  • Blanco Montilla, Ginesa
  • Hernández Garrido, Juan Carlos
A multidisciplinary approach has been followed for the development of structured catalysts based on 3D-printed metallic honeycomb monoliths, which allows overcoming some of the barriers that limit the industrial application of significant catalytic processes such as those related to CO2 valorization. In particular, nickel and/or cerium-containing catalysts have been incorporated into stainless steel honeycombs and evaluated in the Dry Reforming of Methane (DRM) reaction. Moreover, taking advantage of the conductive nature of the metallic substrate, a methodology that allows the incorporation of the active phase by electrochemical deposition has been implemented. The prepared catalysts were characterized by SEM coupled EDX compositional analysis, X-ray fluorescence, X-ray diffraction, X-ray Photoelectron Spectroscopy and Temperature-Programmed Reduction. In contrast to the catalyst where cerium and nickel were co-deposited, the catalyst obtained by sequential electrodeposition of Ce (first) and Ni (second) proved to be highly active and stable in the DRM process, with conversions of both CH4 and CO2 above 90% and H2/CO ratio of ca. 0.8 at 750 ºC for more than 40 h. Moreover, the catalyst kept its good performance after doubling the flow proving its great potential for a real application at higher scale., Ministry of Economy and Competitiveness of Spain (Project PID2020-113006-RB-I00) and the Junta de Andalucía (FQM-110, FQM-334 and TEP-231 groups, and Project P20-00918), Número de páginas: 13
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Tailoring CO2 adsorption and activation properties of ceria nanocubes by coating with nanometre-thick yttria layers

  • Barroso Bogeat, Adrián
  • Blanco Montilla, Ginesa
  • Pintado Caña, José María
  • Goma Jiménez, Daniel
  • Calvino Gámez, José Juan
Ceria (CeO2) is a ubiquitous component in catalysts for environmental protection processes, especially those devoted to CO2 valorisation. Aimed at preparing ceria-based nanomaterials with enhanced CO2 adsorption and activation properties, both the surface acid-base and redox features of ceria nanocubes were modulated by a novel, simple, wet chemistry synthetic strategy consisting of their coating with yttria (Y2O3) layers of variable thickness in the nanometre scale. The as-synthesised samples were characterised with special attention to their surface basicity and reducibility. Characterisation results revealed that the surface doping with yttria not only improved both the reducibility at low temperature and CO2 adsorption capacity of ceria nanocubes, but also introduced a variety of basic sites with different strength. Finally, the careful control of the yttria layer thickness allowed to modulate these effects and thereby the ability of nanostructured ceria to adsorb and activate the CO2 molecule.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

An atomically efficient, highly stable and redox active Ce0.5Tb0.5Ox (3% mol.)/MagO catalyst for total oxidation of methane

  • Sánchez Gil, Juan José
  • López Haro, Miguel
  • Hernández Garrido, Juan Carlos
  • Blanco Montilla, Ginesa
  • Cauqui López, Miguel Ángel
  • Rodríguez-Izquierdo Gil, José María
  • Pérez Omil, José Antonio
  • Calvino Gámez, José Juan
  • Yeste Siguenza, María del Pilar
Redox and catalytic performance in total methane oxidation of a nanostructured ceria-terbia catalyst supported on magnesia is presented and compared to that of a pure ceria catalyst supported on MgO. The investigated material, Ce0.5Tb0.5Ox (3% mol.)/MgO, features several remarkable properties: a quite low total molar loading of the two lanthanide elements, high reducibility as well as very high oxygen storage capacity at low temperatures and higher catalytic activity than MgO supported CeO2. In terms of lanthanide atomic content terms, the catalytic performance of Ce0.5Tb0.5Ox (3% mol.)/MgO largely improves that of bulk type ceria and ceria-magnesia solid solutions. Such behavior implies a proper optimization in the usage of the lanthanide elements. A second contribution to atomic economy in the catalyst design relates to the fact that the novel formulation demonstrates a good stability in the redox and catalytic performance against very high temperature treatments. An investigation of the structure of both the fresh and high temperature-aged catalyst at atomic scale, by means of complementary aberration corrected microscopy techniques, reveals the occurrence of a variety of highly dispersed, exotic, lanthanide-containing nanostructures, which span from isolated, atomically dispersed, Ln species, to nanometer-sized CeTbO2-x patches, extended CeTbO2-x bilayers and 3D CeTbO2-x nanoparticles. Nanoanalytical results evidence mixing of the two lanthanides at atomic levels in these nanostructures. The combined effect of nanostructuring, mixing of the lanthanides at atomic level and interaction with the MgO oxide are at the roots of the improvement in functional, redox and catalytic properties of the novel Ce0.5Tb0.5Ox (3% mol.)/MgO catalyst., The authors acknowledge financial support from FEDER/MINECO Projects (Ref: MAT2017-87579-R and MAT2016-81118-P) and Junta de Andalucía (FQM334, FQM110). The Electron Microscopy data were all acquired at DME SC-ICyT UCA, Se registra la plantilla en la que se ha remitido la versión final que resultó aceptada. Conforme a Sherpa Romeo, pasados dos años se puede facilitar el acceso a la versión final remitida por el autor.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Copper-iron mixed oxide supported onto cordierite honeycomb as a heterogeneous catalyst in the Kharasch-Sosnovsky oxidation of cyclohexene

  • Yeste Siguenza, María del Pilar
  • Fellak, M. Amine
  • Vidal Muñoz, Hilario
  • Guerra Martínez, Francisco Miguel
  • Moreno Dorado, Francisco Javier
  • Gatica Casas, José Manuel
A copper-iron mixed oxide was deposited by the washcoating procedure over cordierite honeycomb monoliths for its use as a heterogeneous catalyst in organic synthesis processes. In particular, the prepared catalyst, characterized by techniques such as X-ray fluorescence, X-ray diffraction, SEM-EDS, laser granulometry, adherence tests, Temperature-Programmed Oxidation and Temperature-Programmed Reduction, showed an excellent yield and stability in the selective production of the allylic ester derived from the Kharasch-Sosnovsky oxidation of cyclohexene with benzoic acid. The use of a structured catalyst here proposed opens up an interesting alternative to homogeneous catalysis in the field of synthetic chemistry. © 2021 The Authors, The authors thank the Ministry of Economy and Competitiveness of Spain (Projects MAT2017-85-719-R , and AGL2017-88083-R ), the Junta de Andalucía ( FQM-110 and FQM-169 groups), and the Institute of Electron Microscopy and Materials (IMEYMAT) of Cadiz University (UCA) (Projects HOMOGREEN and NUPRECAT) for their financial support. They also acknowledge the SC-ICYT of the UCA for using its XRD NMR, and electron microscopy division facilities.