Pasar al contenido principal

SUPERFICIES INTELIGENTES CON PROPIEDADES REPELENTES, AUTO-LIMPIANTES, DESCONTAMINANTES Y AUTO-ESTERILIZANTES

PID2020-115843RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE CADIZ

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Studying the influence of surface properties on the cell attachment and anti-fouling capacity of Ag/SiO2 superhydrophobic coatings for building materials

  • Zarzuela, Rafael
  • Carbú, María
  • Moreno-Garrido, Ignacio
  • Diaz, Ana
  • Cantoral, Jesús M.
  • Almoraima Gil, M.L.
  • Mosquera, María J.
  • Domínguez-Rodríguez, Marcia|||0000-0002-0635-0699
[EN] Anti-fouling coatings are a common solution for the protection of porous building materials from the effects of microbial colonization over their functionality and durability. Usually, this is achieved through the incorporation of biocides or the passive control by reducing bioreceptivity. Superhydrophobic surfaces are considered a promising strategy due to their reported capacity for reducing cell adhesion, but their affinity to non-polar substances may decrease their effectiveness under the right circumstances (e.g. organic contamination, cell walls with hydrophobic domains). The combination of these surfaces with active biocides may compensate these drawbacks, however, a close contact with the microorganisms is necessary to promote their effect.This work studies the factors that determine the anti-fouling capacity of a coating, tested on porous building materials, that combines superhydrophobic surface with a nanostructured Ag/SiO2 biocide agent. Special attention is paid to understanding to which extent the cell-surface interactions modulate the initial cell attachment to the surface and the biocidal effect. To this end, the electrostatic forces and surface energy balance were considered using different reference bacteria and a yeast. The results indicate that the hydrophobic character of the surface favors the cell attachment and the biocide agent may be unable to fully compensate this effect for all microorganisms. In addition, changes in micro and nano roughness seem to play an equally significant role. Overall, this study aims to provide a theoretical and experimental insight to assist in the future design of anti-fouling coatings tailored to the organisms responsible of fouling processes., This work has been financed by the Spanish State Research Agency (MCIN/AEI/ 10.13039/501100011033) R&D programs 2020 2021 (Project references: PID2020-115843RB-I00 and PDC2021-121652-I00); This work has been co-financed by the European Union under the 2014 2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia (Project reference: FEDER- UCA18-106613)
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Strong Metal-Support Interaction (SMSI) in Au/TiO2 photocatalysts for environmental remediation applications: Effectiveness enhancement and side effects

  • Luna Aguilera, Manuel Jesús
  • González Hidalgo, Adrián
  • Díaz, Ana
  • Goma Jiménez, Daniel
  • Gatica Casas, José Manuel
  • Mosquera Díaz, María Jesús
Strong Metal−Support Interaction (SMSI) is a well-known phenomenon of heterogeneous catalysis that have not been extensively investigated in photocatalytic applications. Moreover, the reactions previously studied for photocatalysts under SMSI state are mainly restricted to energy related uses. The present work seeks to explore the effect of SMSI induced by soft wet-chemistry in a Au/TiO2 photocatalyst with specific focus on photocatalytic environmental remediation. With this aim, the developed photocatalyst has been evaluated considering liquid, gas and solid pollutants in order to represent the wide range of environmental photocatalysis applications. These photooxidation scenarios were methylene blue dissolved in water, gaseous NO, and soot directly deposited on the photocatalyst. The results revealed that the SMSI induction has a generally positive effect on photoactivity promoting the MB and soot removal by 53% and 60%, respectively. However, the SMSI did not provide any additional benefit in the NOx elimination compared to the non-SMSI Au/TiO2 photocatalyst, because the enveloping of AuNPs limits the gold-pollutant interaction.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Clay honeycomb monoliths for the simultaneous retention of lead and cadmium in water

  • Ahrouch, M.
  • Gatica Casas, José Manuel
  • Draoui, K.
  • Bellido Milla, Dolores
  • Vidal Muñoz, Hilario
Natural illite-smectite and stevensite Moroccan clays were used for the simultaneous removal of lead and cadmium from aqueous medium. The clays were employed in raw state and extruded as honeycomb monoliths form without any additives, which confirms the novelty of this approach in water treatment. The experiments were done in batch conditions with continuous stirring and using a recirculated flow, respectively. In addition to a characterization of the clays by XRF, XRD, TGA, laser granulometry, N2 physisorption, FTIR spectroscopy, SEM-EDS and evaluation of the cation exchange capacity, special attention was paid to the influence on the co-adsorption of variables such as adsorbent dosage, contact time and initial concentration of Cd2+ and Pb2+. Pseudo-second order kinetics and good fitting to Redlich-Peterson model for both heavy metals were found. Our results also suggest that Pb2+ and Cd2+ uptake is controlled by chemisorption with predominance of Langmuir characteristics. No significant depletion of the metals retention attributable to competition was observed, particularly for the stevensite (maximum retention capacity of 1.2 mg Pb2+/g and 4.6 mg Cd2+/g) that showed higher specific surface area. For both clays, cadmium ions adsorption was relatively favoured in the bimetallic solution, and the honeycombs kept the powders performance. Honeycomb monoliths as a compact adsorbent offer a promising way of water treatment thanks to their stability and easy incorporation into dynamic processes avoiding the issues of pressure drop under wastewater circulation. (c) 2022 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Studying the bulk hydrophobization of cement mortars by the combination of alkylalkoxysilane admixture and fluoropolymer-functionalized aggregate

  • Zarzuela Sánchez, Rafael
  • González-Coneo, Jorge
  • Luna Aguilera, Manuel Jesús
  • Díaz, Ana
  • Mosquera Díaz, María Jesús
In this work, hydrophobic mortars are produced by combining a silane-based admixture with the pre-treatment of the aggregates with an alkoxysilane-ended fluoropolymer. A comparative study is presented to determine the effect of the components, under different curing conditions, on the hydrophobicity, mechanical performance, composition and micro-structure. The combination of both strategies allows obtaining hydrophobic properties at different curing conditions, whereas the silane loses effectiveness at high humidity and the modified aggregate at low humidity. The silane hinders cement hydration and promotes gaps in the aggregate-matrix interfacial transition zone, decreasing mechanical resistance, whereas the modified aggregate changes the interfacial transition zone morphology without significant effects on resistance. The combination of both strategies partially compensates the negative impact of the silane admixture, especially when the mortars are cured at high humidity. Thus, this combination increases versatility of the mortars and poses as a potential route to address the limitations of silane admixtures. © 2022 The Authors
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Studying the influence of surface properties on the cell attachment and anti-fouling capacity of Ag/SiO2 superhydrophobic coatings for building materials

  • Zarzuela Sánchez, Rafael
  • Domínguez, Marcia
  • Carbú Espinosa de los Monteros, María
  • Moreno-Garrido, Ignacio
  • Díaz Sánchez, Ana Belén
  • Cantoral Fernández, Jesús Manuel
  • Gil Montero, María Luisa Almoraima
  • Mosquera Díaz, María Jesús
Anti-fouling coatings are a common solution for the protection of porous building materials from the effects of microbial colonization over their functionality and durability. Usually, this is achieved through the incorporation of biocides or the passive control by reducing bioreceptivity. Superhydrophobic surfaces are considered a promising strategy due to their reported capacity for reducing cell adhesion, but their affinity to non-polar substances may decrease their effectiveness under the right circumstances (e.g. organic contamination, cell walls with hydrophobic domains). The combination of these surfaces with active biocides may compensate these drawbacks, however, a close contact with the microorganisms is necessary to promote their effect. This work studies the factors that determine the anti-fouling capacity of a coating, tested on porous building materials, that combines superhydrophobic surface with a nanostructured Ag/SiO2 biocide agent. Special attention is paid to understanding to which extent the cell-surface interactions modulate the initial cell attachment to the surface and the biocidal effect. To this end, the electrostatic forces and surface energy balance were considered using different reference bacteria and a yeast. The results indicate that the hydrophobic character of the surface favors the cell attachment and the biocide agent may be unable to fully compensate this effect for all microorganisms. In addition, changes in micro and nano roughness seem to play an equally significant role. Overall, this study aims to provide a theoretical and experimental insight to assist in the future design of anti-fouling coatings tailored to the organisms responsible of fouling processes.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Study of the nickel removal from water applying Design of Experiments and using natural clay honeycomb monoliths

  • Bellido Milla, Dolores
  • Vidal Muñoz, Hilario
  • Núñez, María
  • Ahrouch, Mohammadi
  • Gatica Casas, José Manuel
A natural Moroccan illite-smectite clay was investigated as adsorbent of nickel in water. Before its use, it was processed without additives as honeycomb monoliths, an advantageous design in many methods developed to control environmental pollution. The performance of the resulting monoliths was studied in dynamic conditions by flow recirculation through the honeycombs and using Atomic Absorption Spectroscopy for the determination of residual nickel concentration in the solutions. Design of experiments (DoE) was employed to evaluate the influence of three parameters and their interaction on the nickel adsorption capacity of the clay honeycombs: nickel concentration (10–206 ppm), salt concentration (4–36 g/L), and water flow (94–364 mL/min). Based on previous studies, recirculation time, pH and temperature were fixed at 1 h, 4.5 and room temperature, respectively. The maximum amount of nickel adsorbed (0.83 mg/g of clay) was obtained for a nickel concentration of 206 ppm, a 218 mL/min flow, and a salt concentration of 4 g/L. Experimental conditions for the highest repeatability were estimated, the respective values being 108.2 ppm, 94 mL/min and 20 g/L. Nickel retention by the clay was also confirmed after the adsorption tests by direct characterization of the used structured adsorbent through X-ray Fluorescence and SEM-EDS.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

The Role of Surface {010} Facets in Improving the NOx Depolluting Activity of TiO2 and Its Application on Building Materials

  • Luna Aguilera, Manuel Jesús
  • Cruces, J.L.
  • Gatica Casas, José Manuel
  • Cruceira Fernández de Arjona, Álvaro
  • Cifredo Chacón, Gustavo Aurelio
  • Vidal Muñoz, Hilario
  • Mosquera Díaz, María Jesús
Air pollution, a major health concern, necessitates innovative solutions such as TiO2-based photocatalytic building materials to combat its harmful effects. This study focuses on developing high-performance TiO2 photocatalysts for NOx removal in building applications, aiming to overcome the limitations of commercial TiO2. These photocatalysts were synthesized via a hydrothermal method, with parameters such as synthesis time and post-treatment investigated to optimize their properties. Hydrothermal synthesis yielded TiO2 nanoparticles with reduced aggregation and a high proportion of elongated particles with exposed {010} facets. This resulted in significantly enhanced photocatalytic activity compared to commercial P25 in methylene blue degradation and NOx depollution. Subsequently, the optimized hydrothermal TiO2 was successfully integrated into a silica sol–gel coating for application on building materials. The coated concrete demonstrated significantly higher NOx removal efficiency and lower NO2 release, achieving a 1.7-fold improvement in overall NOx removal and significantly higher depolluting effectiveness compared to its P25 counterpart. These findings highlight the potential of hydrothermally synthesized TiO2 with controlled morphology for the development of high-performance, environmentally friendly building materials with enhanced air purification capabilities.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Cu-TiO2/SiO2 photocatalysts for concrete-based building materials: Self-cleaning and air de-pollution performance

  • Khannyra, Souad
  • Mosquera Díaz, María Jesús
  • Addou, Mohammed
  • Gil Montero, María Luisa Almoraima
As a consequence of human activities, today, we are exposed to high pollution levels that cause building materials damage and many diseases. The application of TiO2 as coating on building materials has proven the efficiency of self-cleaning and air de-pollution. However, its performance is limited due to its absorption being exclusively located at UV light. In this study, Cu-TiO2 photocatalysts were integrated into silica sol-gel synthesis to manufacture new long-lasting term coatings with self-cleaning and air purification properties for concretebased building materials. The enhancement of TiO2 photoactivity by incorporating Cu into its network has been clearly demonstrated. The self-cleaning and air de-polluting efficiency were assessed using methylene blue (MB), soot and NO, respectively, indicating that the presence of Cu promotes the TiO2 performance. For low doping levels, by increasing the copper loading, the TiO2 photoactivity increased. The highest efficiency was obtained by the photocatalyst containing 5% copper, which shows maximum destruction of methylene blue and soot of 95% and 50% within 60 min and 168 h of irradiation, respectively. However, higher copper loading led to a decrease in its performance, reaching a total degradation of MB and soot of 90% and 45% after 60 min and 168 h of irradiation, respectively, for the sample containing 15% of copper loading., This work has been supported by the Spanish Government/FEDEREUMAT2017-84228-R, MINECO/AEI/FEDER/UE) and PID2020115843RB-I00/AEI/10.13039/501100011033. This work has been cofinanced by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106613. We want to thank Margarita Carballido, Mercedes Marquez and Sergio Moreno to facilitate the real exposure of the samples.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Exploring the low cell adhesion of photoinduced superhydrophilic surfaces for improving the effect of antifouling protective coatings on porous building materials

  • Zarzuela Sánchez, Rafael
  • Cervera, Jaime J.
  • Moreno Corbacho, Ignacio
  • Gil Montero, María Luisa Almoraima
  • Mosquera Díaz, María Jesús
The susceptibility of building materials to biological colonization is associated with accelerated decay processes, aesthetical alterations and health risks. Thus, preventive measurements involving the use of coatings with passive (bioreceptivity decrease) and active (biocides) antifouling mechanisms are common. Hydrophobic and superhydrophobic coatings that decrease water availability are the most common anti-fouling strategies, although they can promote cell adhesion under the right circumstances and lose effectiveness after the initial biofilm setting. In this work, we explore an innovative alternative strategy to improve the anti-fouling effect of a hydrophobic coating through surface modification to grant low cell-adhesion superhydrophilic properties (while preserving its low water absorption) and its combination with nano-biocides. This is achieved by the incorporation of Ag or CuO-modified TiO2 into an ormosil sol–gel matrix. Irradiation with UV–Vis light activates the superhydrophilic surface while maintaining a decrease in capillary water absorption of >90% and accelerated algal exposure tests showed a markedly lower colonization rate compared to the superhydrophobic surface, owing to the modifications in cell-water-surface interfacial tensions. The nano-biocides showed a dual effect, promoting the transition to superhydrophilic and further decreasing colonization. Furthermore, the superhydrophilic surfaces enhance the biocide effect by promoting the interaction of the nanoparticles with the surrounding media., 16 páginas
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Water-soluble fluorosilane supplemented with fumed silica as admixture for producing hydrophobic concrete: Effects on cement hydration, mechanical properties and water protection properties

  • González-Coneo, Jorge
  • Zarzuela Sánchez, Rafael
  • Luna Aguilera, Manuel Jesús
  • Mosquera Díaz, María Jesús
Hydrophobic admixtures protect concrete from water-related degradation, although they may have negative effects over cement hydration, mechanical properties and have low miscibility with water. Aiming to overcome these drawbacks, this work studies the properties of concretes containing admixtures based on a water-soluble fluoroalkylsilane and fumed silica to densify the structure. The effects of the admixture were evaluated in terms of hydrophobic, mechanical and chemical properties. The admixture decreased capillary absorption by over 70% while also increasing the internal cohesion, despite an increased porosity. Raman and XRD analysis indicated it promoted the consumption of C3S and the formation of portlandite and C–S–H gels with higher silicon content, compensating the effect of porosity on the concrete resistance. Incorporation of fumed silica in the admixture delayed the early development of hydrated phases, but after full curing promoted a more compact structure of the cement matrix, decreasing water absorption rate and improving mechanical properties.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Photocatalytic TiO2 nanosheets-SiO2 coatings on concrete and limestone: An enhancement of de-polluting and self-cleaning properties by nanoparticle design

  • Luna Aguilera, Manuel Jesús
  • Delgado Jaén, Juan José
  • Romero Ocaña, Ismael
  • Montini, T.
  • Gil Montero, María Luisa Almoraima
  • Martínez López, Francisco Javier
  • Fornasiero, P.
  • Mosquera Díaz, María Jesús
In this study, we develop TiO2-SiO2 nanocomposites that can be employed as photoactive coatings to create surfaces with antipollution and self-cleaning properties in urban buildings. In particular, anatase titanium dioxide with a high percentage of {001} facets, commonly called titania nanosheet (TNS), was used as active phase. This approach allows us to improve the antipollution properties of similar sols based on P25. The obtained TNS were intensively characterized by UV–Vis diffuse reflectance absorption, X-Ray diffraction and transmission electron microscopy to rationalize the sol synthesis and fully understand the photocatalytic performances. Our results clearly show that after treating the titania nanosheets with NaOH to remove adsorbed residual fluoride from the synthesis, they can be easily dispersed and the photocatalytic activity is dramatically improved. This material has been shown to effectively reduce concentrations of NOx, soot and organic dyes under simulated sun light radiation.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Self-cleaning durability assessment of TiO2/SiO2 photocatalysts coated concrete: Effect of indoor and outdoor conditions on the photocatalytic activity

  • Khannyra, Souad
  • Luna Aguilera, Manuel Jesús
  • Gil Montero, María Luisa Almoraima
  • Addou, Mohammed
  • Mosquera Díaz, María Jesús
A self-cleaning nanostructured TiO2 coating has demonstrated the capacity to mitigate undesired effects from air pollution. Not only it reduces the deterioration of building materials but may also prevent certain pollution-related human health problems. In this study, mesoporous TiO2/SiO2 photocatalysts were synthesized in order to produce self-cleaning and long-lasting coatings that meet the necessary requirements for outdoor applications. The synthesized products were sprayed on concrete substrates and their self-cleaning and air depolluting capabilities were evaluated. The former one as a function of methylene blue (MB) and soot degradation and the latter, according to nitrogen oxides reduction. The coatings proved to have high photocatalytic activity, and their efficiency was enhanced as TiO2 loadings were increased. Thus, after the first 60 min of their irradiation by UV–vis light, the photocatalysts ST1 and S4T had removed 79% and 95% of the MB, respectively. These coatings presented particulate surfaces that provided more surface area and porosity, which are key factors for a high photocatalytic activity. Moreover, the same samples after 104 h of irradiation exhibited 38% and 49% conversion of total NO, respectively. While E503, a commercially available photocatalyst, produced coating cracked surfaces and a total MB degradation of just 50% after 60 min of irradiation as well as 35% of NO conversion after 104 h of irradiation. The TiO2/SiO2 coatings’ photocatalytic efficacy remained practically invariable after four months of exposure to real-life conditions and three MB degradation cycles. After the outdoor durability tests, the coated surfaces exhibited a practically unchanged structure, which confirms their long-lasting efficiency. © 2022 The Authors, This work has been supported by the Spanish Government MAT2017-84228-R (MINECO/AEI//FEDER, UE) and PID2020- 115843RB-I00/AEI/10.13039/501100011033 . This work has been co-financed by the European Union under the 2014–2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia . Project reference: FEDER-UCA18-106613 .
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Alkoxysilane-based consolidation treatments: Laboratory and 3-years In-Situ assessment tests on biocalcarenite stone from Roman Theatre (Cadiz)

  • Gemelli, Giada María Chiara
  • Zarzuela Sánchez, Rafael
  • Alarcón-Castellano, Francisco
  • Mosquera Díaz, María Jesús
  • Gil Montero, María Luisa Almoraima
This manuscript presents a 1 year in the laboratory and 3 years In-Situ evaluation of an alkoxysilane-based consolidant containing SiO2 nanoparticles (SiO2NPs) on Ostionera stone, a biocalcarenite traditionally employed in Southwestern Spain. C ' adiz Roman Theatre was selected for In-Situ application and testing. In order to safeguard the theatre, preliminary laboratory experiments were carried out. Firstly, the compatibility and the effectiveness of the consolidant product were evaluated in the laboratory, demonstrating that the incorporation of SiO2NPs improves drying time and consolidant effect. Subsequently, the consolidant was applied In-Situ and the long-term performance was monitored over 3 years through non-destructive tests. The treatment exhibit moderate incompatibility degree (6.1) and demonstrating the long-lasting performance of the SiO2NPs-based consolidant treatment., 1 This work has been supported by the Spanish Government MAT2017-84228-R (MINECO/AEI//FEDER,UE) and PID2020-115843RB-I00/AEI/10.13039/501100011033. This work been cofinanced by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106613. Giada M.C. Gemelli would also like to thank the Spanish Government for her predoctoral grants (PRE2018-085799). We thank the Cadiz Roman Theatre staff and Manuel Luna for their collaboration.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Validation of alkoxysilane-based protective treatments for increasing service life of cementitious materials under different weathering conditions

  • Zarzuela Sánchez, Rafael
  • Luna Aguilera, Manuel Jesús
  • Gemelli, Giada María Chiara
  • González-Coneo, Jorge
  • Garcia-Lodeiro, Inés
  • Blanco-Varela, María Teresa
  • Mosquera Díaz, María Jesús
Gradual degradation of cementitious materials by exposure to the environment decreases the lifespan of buildings, increasing maintenance andrepair costs. Surface treatments based on alkoxysilanes may prevent weathering effects and repair onset damages, though little attention is paid to how the physical-chemical alterations caused by weathering affect their performance. This work reports a comprehensive characterization/validation of an alkoxysilane-based protective treatment on a mortar subjected to different artificial aging processes (freeze-thaw, thermal cycles, carbonation and chlorides), including measurements of water transport, mechanical properties, reaction products and durability under freeze-thaw and sulfate exposure cycles. Formation of compact silica and C-S-H gel structures decreases porosity and water absorption rate with minimal effect on vapor permeability. Bulk mechanical reinforcement and waterproofing are substantially limited on freeze-thaw aged mortars, whereas surface hardness is barely increased for carbonated mortars. These properties were found to effectively increase the mortar resistance against sulfate and freeze-thaw induced damages.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Influence of gold nanoparticles size for photocatalytic NO oxidation in low loading Au/TiO2 catalysts

  • Luna Aguilera, Manuel Jesús
  • Cruceira Fernández de Arjona, Álvaro
  • Díaz Sánchez, Ana Belén
  • Gatica Casas, José Manuel
  • Mosquera Díaz, María Jesús
Gold nanoparticles (AuNPs) supported on TiO2 are one of the most investigated photocat-alysts, however, the positive effect of AuNPs size reduction on Au/TiO2 activity is clear for conventional catalysis, but this relationship not strictly happens in photocatalysis. The present work investigates how small changes in the lower size range of AuNPs can affect the Au/TiO2 photoactivity in order to maximize the performance of photocatalysts with low metal loadings (<1 wt%). Precipitation-deposition methods and a speciation-controlled incipient wetness impregnation (ScIWI) method have been employed for preparing Au/TiO2 photocatalysts that exhibited a NOx elimination capacity significantly higher than pristine TiO2. Comparing the photocatalysts, ScIWI method achieved the highest gold dispersion and Au-TiO2 contact perimeter providing the most active photocatalysts, confirming the positive effect of AuNPs size reduction in the average sizes around 2 nm. In addition, on the basis of the results obtained, it has been proposed that the adsorption of nitrogen oxides species on gold has a relevant role on the NO photooxidation process.(c) 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Tesis doctoral (DoctoralThesis)

Desarrollo de hormigones con acción hidrofóbica y repelente al agua

  • González-Coneo, Jorge
En la mayor parte de los procesos de deterioro del hormigón, tales como corrosión, cristalización de sales o biodeterioro, interviene el agua. Para reducir la absorción de agua, se suelen emplear tratamientos superficiales que generan una superficie hidrófoba. Su principal inconveniente se relaciona con la limitada durabilidad de su efecto protector que está asociado a la escasa penetración de los tratamientos en el hormigón. Otra estrategia alternativa es la incorporación del componente hidrófobo, como aditivo, durante el proceso de fabricación. No obstante, esta estrategia presenta también inconvenientes asociados a la ralentización de las reacciones de hidratación del cemento y a la dificultad de mezclado de los componentes, que provocan un claro empeoramiento de las propiedades mecánicas del material. En esta Tesis Doctoral, se han desarrollado diversas estrategias de síntesis para producir tres formulaciones, basadas en alcoxisilanos, con aplicación como aditivos en el proceso de fabricación del hormigón. Las formulaciones son empleada con el objetivo de dotar al hormigón de propiedades hidrófobas y establecer, además, una interacción efectiva con las fases cementantes, promoviendo la formación de silicato de calcio hidratado (gel C-S-H). Adicionalmente, se exploró la incorporación de áridos funcionalizados con un agente hidrófobo con capacidad de interaccionar simultáneamente con los componentes del hormigón y con las formulaciones objeto de investigación. Para evaluar la efectividad de las estrategias empleadas, se ha llevado a cabo una completa caracterización de los siguientes parámetros: (i) procesos de hidratación del cemento en presencia de las formulaciones desarrolladas; (ii) interacciones químicas entre los componentes del hormigón y las formulaciones; (iii) microestructura del hormigón fabricado y (iv) propiedades mecánicas, hídricas y texturales del hormigón. Los resultados obtenidos han demostrado que las estrategias aplicadas permiten obtener hormigones con una elevada resistencia a la absorción de agua, consiguiéndose la repelencia en algunas de las formulaciones ensayadas. Además, se confirmó que la formación de silicato de calcio hidratado, como consecuencia de la interacción entre alcoxisilano y portlandita resultante de las reacciones de hidratación, contribuyen a una mayor cohesión del hormigón fabricado. También se determinó que las condiciones de curado tienen un efecto significativo en el comportamiento hidrofugante de los materiales, siendo más favorable en las condiciones de humedad reducida. Por último, destacar que en una de las formulaciones desarrolladas se comparó la eficacia y durabilidad del tratamiento aplicado como aditivo, con respecto a su aplicación en superficie y también se comparó con productos comerciales. En todos los casos, los mejores resultados fueron obtenidos con la formación desarrollada en nuestro laboratorio y aplicada como aditivo en el proceso de fabricación del hormigón.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Alkylsiloxane/alkoxysilane sols as hydrophobic treatments for concrete: A comparative study of bulk vs surface application

  • González-Coneo, Jorge
  • Zarzuela Sánchez, Rafael
  • Elhaddad, Farid
  • Martínez Carrascosa, Luis Antonio
  • Gil Montero, María Luisa Almoraima
  • Mosquera Díaz, María Jesús
Water and waterborne decay agents (e.g. salts, microorganisms) are commonly associated with undesired alterations and damages on concrete elements. A strategy to mitigate their impact is to decrease water retention in the material either by surface treatments or admixtures. In this work, hydrophobic concretes were developed by the addition of a hydrophobic sol containing TEOS and PDMS oligomers, synthetized by a surfactant-assisted sol-gel route, either as an admixture or as a surface treatment. The hydrophobic performance was similar for both application modes (>70% capillary absorption reduction) and higher than concrete containing a commercial (calcium stearate) admixture or a nanosilica-based hydrophobic coating. Addition as an admixture led to a higher durability in the rain and abrasion tests. The hydrophobic sol as an admixture promotes an increase of surface roughness and porosity, as well as the formation of C–S–H like reaction products with the cement matrix components, as evidenced by AFM, MIP, SEM and FTIR. Despite the higher porosity, impact resistance and material cohesion were not negatively affected respect to the plain concrete. Application as a surface treatment decreased porosity and led to a higher amorphous SiO2 content. The material cohesion and impact resistance was increased by this application, although penetration was limited to the first 4 mm and the hydrophobic properties were more susceptible to mechanical damages to the surface. © 2021 The Authors, This project has received funding from the European Union's Horizon 2020 - Research and Innovation Framework Programme under grant agreement No 760858; This work has been financed by the Spanish State Research Agency R&D program 2020 (Project reference: PID2020-115843RB-I00); This work has been co-financed by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia (Project reference: FEDER- UCA18-106613).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Multifunctional silane-based superhydrophobic/impregnation treatments for concrete producing C-S-H gel: Validation on mockup specimens from European heritage structures

  • Zarzuela Sánchez, Rafael
  • Luna Aguilera, Manuel Jesús
  • González-Coneo, Jorge
  • Gemelli, Giada María Chiara
  • Andreouli, Dia
  • Kaloidas, Vasilis
  • Mosquera Díaz, María Jesús
Many of the concrete structures that conform our modern cultural heritage are in need of repair and protective interventions. Silane-based impregnation treatments can be used to repair onset cracks and reinforce the surface due to their ability to produce silica and C-S-H gels, and can be modified by incorporating hydrophobic precursors to create multifunctional treatments that also protect from water ingress. Since the effectiveness of impregnation treatments is dependent on substrate properties and chemical-physical changes it may have experienced over time, validation using standard materials may not always be representative of on-site application. In this work, the effectiveness of three innovative silane-based impregnation treatments developed by our group (two of them combining superhydrophobic properties) was evaluated on mockup specimens, which simulate the properties of the cementitious materials from six different heritage structures across Europe, artificially aged to simulate weathering by three methods: carbonation, chloride ingress and physical damages (freeze–thaw and thermal cycles). The characterization of the treatments showed they are compatible in terms of chemical interaction, applicability and minimal aesthetical alterations. Surface resistance and ultrasound pulse measurements have been used to assess the improvement in mechanical properties. The incorporation of hydrophobic components and fumed silica has a relatively low impact over the mechanical properties while it significantly reduces water absorption and grants water repellent properties to the surface, giving rise to a superhydrophobic performance. © 2022 The Authors
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Achieving superhydrophobic surfaces with tunable roughness on building materials via nanosecond laser texturing of silane/ siloxane coatings

  • Martínez Carrascosa, Luis Antonio
  • Zarzuela Sánchez, Rafael
  • Botana Galvín, Marta
  • Botana Pedemonte, Francisco Javier
  • Mosquera Díaz, María Jesús
In this work, we employ a versatile laser-based top-down approach that allows to create superhydrophobic and hydrophobic surfaces, with controlled roughness and wetting properties, on marble and potentially other building materials. The process involves two stages: (1) application of an organically modified silica coating to reduce surface energy. (2) Controlled texturing of the coating by ablation using a nanosecond-pulse laser. In general terms, at higher laser fluence (energy per unity of area), the contact angles increased from 110 degrees of the non-textured surface to values around 155 degrees, following a nearly linear correlation with the measured roughness values. Starting from fluence values of 154 J cm-2, the surfaces displayed water repellence (hysteresis <= 10 degrees) and the micrographs showed the formation of sub-micrometric structures on top of the micro-roughness by melting and re-deposition of the coating material, suggesting the formation of a Cassie-Baxter wetting regime. Ablation at lower fluences created a random micro-roughness, leading to static contact angles of 135-145 degrees but no water repellence, which is indicative of a Wenzel wetting regime. At the highest fluence values tested, the increasing trends respect roughness and hydrophobic/water repellent properties are inverted due to the damages suffered by the coating. In terms of durability, the coating demonstrated a good adhesion to the stone surface, maintaining its superhydrophobic properties after repeated cycles of an "adhesive tape test". The sand falling test showed that water repellence is relatively sensitive to abrasion, although the hydrophobic character of the coating is maintained.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Dye decomposition and air de-pollution performance of TiO2/SiO2 and N-TiO2/SiO2 photocatalysts coated on Portland cement mortar substates

  • Khannyra, Souad
  • Gil Montero, María Luisa Almoraima
  • Addou, Mohammed
  • Mosquera Díaz, María Jesús
In this study, the newly synthesized TiO2 and N doped TiO2 clusters were added to silica sol to synthesize N-TiO2/SiO2 composites via the sol-gel method. Afterwards, the prepared cols were applied by brushing on portland cement. Doping with nitrogen significantly increased the absorption of TiO2 towards the visible region, thus, increasing the photocatalytic activity. SEM characterization of the treated samples showed that the clusters were distributed in form of aggregates on the samples' surface. The self-cleaning and air de-polluting performances were assessed through methylene blue degradation and the oxidation of nitrogen oxide, resulting in methylene blue (MB) removal of 85% and 78% after 60 min of irradiation for SN10TiO(2) and STiO2, respectively. Regarding air de-pollution performance, the newly synthesized photocatalysts showed the ability of NOx reduction. However, their efficiency was somewhat lower, in which 23.81% of NO has been oxidized by the sample SN10TiO(2), while SP25 showed a total NO conversion of 38.98%. The powdered xerogels of the newly synthesized nanoparticles revealed high photocatalytic efficiency concerning NO oxidation, resulting in a higher performance compared to those obtained by the xerogel containing P25, Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This project has received funding from the European Union's Horizon 2020 Research and Innovation Framework Programme under grant agreement no 760858. This work has been financed by the Spanish State Research Agency R&D programme 2020 (Project reference: PID2020-115843RB-I00) and has been co-financed by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia (Project reference: FEDER-UCA18-106613). S. Khannyra would also like to thank the Aula del Estrecho of the University of Cadiz for her predoctoral grant.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

4-Year in-situ assessment of a photocatalytic TiO2/SiO2 antifouling treatment for historic mortar in a coastal city

  • Gemelli, Giada M. C.
  • Luna, Manuel
  • Zarzuela, Rafael
  • Almoraima Gil, M. L.
  • Carbú, María
  • Moreno-Garrido, Ignacio
  • Mosquera, María J.
This manuscript presents a 4 years in-situ evaluation of TiO2/SiO2-based product applied to a mortar seating belonging to the bleachers of the Cadiz Roman Theatre, affected by biofouling and organic deposits. Antifouling performance was studied by colorimetric measurements and ATP analyses. Surface sampling was performed for biofouling identification, being remarkable the presence of filamentous fungi and cyanobacteria. Additionally, antifouling performance was checked during a 4 years in-situ monitoring study. SEM observations, carried out 4 years after the product application, demonstrate that the TiO2 integration in a SiO2 matrix produces a durable coating which allows for prolongation of the antifouling performance over time. According to the results obtained, 4 years after the application of the treatment, the treated area still maintains its antifouling efficacy, exhibiting a 40% reduction in organic deposit and 61% inhibition of biological growth compared to the untreated area. The results of this study show that the application of the SiO2/TiO2-based product may potentially reduce the costs of cleaning and maintenance works. At the same time, it is considered that the antifouling efficacy is more pronounced during the first two years and could be taken into account in the maintenance and re-application actions., This work has been supported by the Spanish Government MAT2017-84228-R (MINECO/AEI//FEDER, UE) and PID2020- 115843RB-I00/AEI/10.13039/501100011033. This work has been co-financed by the European Union under the 2014–2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia. Project reference: FEDER-UCA18-106613. Giada M.C. Gemelli would also like to thank the Spanish Government for her pre-doctoral grants (PRE2018-085799). M. Luna would also like to thank the Spanish Government for his Margarita Salas grant (2021-067/PN/MS-RECUAL/CD) supported by the European Union-NextGenerationEU., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploring the low cell adhesion of photoinduced superhydrophilic surfaces for improving the effect of antifouling protective coatings on porous building materials

  • Zarzuela, Rafael
  • Cervera, Jaime J.
  • Moreno de Alborán, Ignacio
  • Almoraima Gil, M. L.
  • Mosquera, María J.
The susceptibility of building materials to biological colonization is associated with accelerated decay processes, aesthetical alterations and health risks. Thus, preventive measurements involving the use of coatings with passive (bioreceptivity decrease) and active (biocides) antifouling mechanisms are common. Hydrophobic and superhydrophobic coatings that decrease water availability are the most common anti-fouling strategies, although they can promote cell adhesion under the right circumstances and lose effectiveness after the initial biofilm setting. In this work, we explore an innovative alternative strategy to improve the anti-fouling effect of a hydrophobic coating through surface modification to grant low cell-adhesion superhydrophilic properties (while preserving its low water absorption) and its combination with nano-biocides. This is achieved by the incorporation of Ag or CuO-modified TiO2 into an ormosil sol–gel matrix. Irradiation with UV–Vis light activates the superhydrophilic surface while maintaining a decrease in capillary water absorption of >90% and accelerated algal exposure tests showed a markedly lower colonization rate compared to the superhydrophobic surface, owing to the modifications in cell-water-surface interfacial tensions. The nano-biocides showed a dual effect, promoting the transition to superhydrophilic and further decreasing colonization. Furthermore, the superhydrophilic surfaces enhance the biocide effect by promoting the interaction of the nanoparticles with the surrounding media., This work has been supported under grant PID2020-115843RB-I00 funded by MCIN/AEI/ 10.13039/501100011033; This work has been co-financed by the European Union under the 2014-2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia (Project reference: FEDER-UCA18-106613)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Studying the influence of surface properties on the cell attachment and anti-fouling capacity of Ag/SiO2 superhydrophobic coatings for building materials

  • Zarzuela, Rafael
  • Domínguez, Marcia
  • Carbú, María
  • Moreno-Garrido, Ignacio
  • Diaz, Ana
  • Cantoral, Jesús M.
  • Almoraima Gil, M. L.
  • Mosquera, María J.
Anti-fouling coatings are a common solution for the protection of porous building materials from the effects of microbial colonization over their functionality and durability. Usually, this is achieved through the incorporation of biocides or the passive control by reducing bioreceptivity. Superhydrophobic surfaces are considered a promising strategy due to their reported capacity for reducing cell adhesion, but their affinity to non-polar substances may decrease their effectiveness under the right circumstances (e.g. organic contamination, cell walls with hydrophobic domains). The combination of these surfaces with active biocides may compensate these drawbacks, however, a close contact with the microorganisms is necessary to promote their effect. This work studies the factors that determine the anti-fouling capacity of a coating, tested on porous building materials, that combines superhydrophobic surface with a nanostructured Ag/SiO2 biocide agent. Special attention is paid to understanding to which extent the cell-surface interactions modulate the initial cell attachment to the surface and the biocidal effect. To this end, the electrostatic forces and surface energy balance were considered using different reference bacteria and a yeast. The results indicate that the hydrophobic character of the surface favors the cell attachment and the biocide agent may be unable to fully compensate this effect for all microorganisms. In addition, changes in micro and nano roughness seem to play an equally significant role. Overall, this study aims to provide a theoretical and experimental insight to assist in the future design of anti-fouling coatings tailored to the organisms responsible of fouling processes., This work has been financed by the Spanish State Research Agency (MCIN/AEI/ 10.13039/501100011033) R&D programs 2020–2021 (Project references: PID2020-115843RB-I00 and PDC2021-121652-I00); This work has been co-financed by the European Union under the 2014–2020 ERDF Operational Programme and by the Department of Economic Transformation, Industry, Knowledge, and Universities of the Regional Government of Andalusia (Project reference: FEDER- UCA18-106613), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Validation of alkoxysilane-based protective treatments for increasing service life of cementitious materials under different weathering conditions

  • Zarzuela, Rafael
  • Luna, Manuel
  • Gemelli, Giada
  • Gonzalez-Coneo, Jorge
  • García-Lodeiro, Inés
  • Blanco-Varela, María Teresa
  • Mosquera, Maria Jesus
Gradual degradation of cementitious materials by exposure to the environment decreases the lifespan of buildings, increasing maintenance andrepair costs. Surface treatments based on alkoxysilanes may prevent weathering effects and repair onset damages, though little attention is paid to how the physical-chemical alterations caused by weathering affect their performance. This work reports a comprehensive characterization/validation of an alkoxysilane-based protective treatment on a mortar subjected to different artificial aging processes (freeze-thaw, thermal cycles, carbonation and chlorides), including measurements of water transport, mechanical properties, reaction products and durability under freeze-thaw and sulfate exposure cycles. Formation of compact silica and C-S-H gel structures decreases porosity and water absorption rate with minimal effect on vapor permeability. Bulk mechanical reinforcement and waterproofing are substantially limited on freeze-thaw aged mortars, whereas surface hardness is barely increased for carbonated mortars. These properties were found to effectively increase the mortar resistance against sulfate and freeze-thaw induced damages., Peer reviewed