Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Nano-heaters: New insights on the outstanding deposition of dielectric energy on perovskite nanoparticles

  • Gracia, J.
  • Escuin, M.
  • Mallada, R.
  • Navascues, N.
  • Santamaria, J.
It has been experimentally observed that, in some Mott nanomaterials, outstanding dielectric losses may appear at microwave frequencies, leading to a rapid increase of temperature. This often takes place in association with the insulator to metal transition (IMT) in these materials. However, when other materials with a similar structure and composition are subjected to the same intensity of microwave (MW) irradiation, the observed heating is minimal. Here we show that the electron dynamics of these materials are responsible for their different heating behaviour. More specifically, for LaCoO3 perovskite nanoparticles, the spin shifts causing the IMT are also responsible for the observed heating behaviour. Under suitable conditions, the intense absorption of MW radiation leads to extremely high heating rates, above 600 degrees per second. The insight gained from this study has been used to design a directly heated catalytic system (LaCoO3 perovskite nanoparticles on a MW-transparent cordierite monolith) capable to operate under a stable, significant solid-gas temperature gradient.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Electrospun Au/CeO2 nanofibers: A highly accessible low-pressure drop catalyst for preferential CO oxidation

  • Moreno, I.
  • Navascues, N.
  • Irusta, S.
  • Santamaria, J.
Au/CeO2 catalysts shaped as nanofibers were obtained by supporting Au nanoparticles (ca. 3 nm) on CeO2 nanofibers of around 200 nm diameter. The CeO2 support was prepared by calcining electrospun polymer nanocomposite fibers with a high Ce content; then gold nanoparticles were either synthesized in situ or deposited from a suspension. The prepared catalysts were used in the preferential oxidation of CO in a hydrogen-rich stream. The catalysts prepared by deposition of preformed gold nanoparticles were less stable and underwent sintering due to a weaker nanoparticle–support interaction. In contrast, the catalysts with Au nanoparticles synthesized in situ were active (90% conversion and 46% selectivity) and stable. The fiber-shaped catalyst was able to give maximum reactant access at a much lower pressure drop than catalyst in powder form.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Amine-functionalized mesoporous silica: A material capable of CO2 adsorption and fast regeneration by microwave heating

  • Nigar, H.
  • Garcia-Baños, B.
  • Peñaranda-Foix, F.L.
  • Catalá-Civera, J.M.
  • Mallada, R.
  • Santamaría, J.
The surface of ordered mesoporous (MCM-48) silica has been subjected to covalent grafting with silane molecules containing one to three amino groups. The dielectric properties of the materials were studied in detail, and the functionalized materials were used for CO2 adsorption at room temperature, followed by regeneration under either conventional heating or microwave irradiation. It has been found that, as the intensity of functionalization with amino groups increases (from mono- to tri-amino silanes) both the CO2 load and the dielectric response at microwave frequencies increase. In particular, functionalization with a tri-amino silane derivative gave the highest CO2 adsorption and the fastest microwave heating, resulting in a fourfold acceleration of adsorbent regeneration. The grafted material was fully stable for at least 20 adsorption-regeneration cycles, making it an ideal candidate for microwave-swing adsorption (MWSA) processes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ethylene epoxidation in microwave heated structured reactors

  • Ramírez, A.
  • Hueso, J. L.
  • Mallada, R.
  • Santamaría, J.
In the present work we show the microwave-induced heating of monolithic reactors containing a thin-layered catalyst that exhibits a strong and selective heating susceptibility under microwave irradiation. The combination of microwave radiation and structured reactors has been successfully applied for the intensification of the selective oxidation of ethylene to ethylene oxide (epoxidation) while operating at lower power consumptions and with higher energy efficiencies than in conventional heating conditions. The microwave radiation selectively heats the catalyst and the monolith walls while maintaining a relatively colder gas stream thereby creating a gas/solid temperature gradient of up to ~70 °C at a reaction temperature of 225 °C. Moreover, the influence of different parameters such as the distribution of the catalyst onto the structured monoliths or the temperature measurement techniques employed to determine the heating profiles (Optic Fibers and/or IR thermography) have been also thoroughly evaluated to justify the obtained catalytic results.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

A Nanoarchitecture Based on Silver and Copper Oxide with an Exceptional Response in the Chlorine-Promoted Epoxidation of Ethylene

  • Ramirez, A.
  • Hueso, J. L.
  • Suarez, H.
  • Mallada, R.
  • Ibarra, A.
  • Irusta, S.
  • Santamaria, J.
The selective oxidation of ethylene to ethylene epoxide is highly challenging as a result of competing reaction pathways leading to the deep oxidation of both ethylene and ethylene oxide. Herein we present a novel catalyst based on silver and copper oxide with an excellent response in the selective oxidation pathway towards ethylene epoxide. The catalyst is composed of different silver nanostructures dispersed on a tubular copper oxide matrix. This type of hybrid nanoarchitecture seems to facilitate the accommodation of chlorine promoters, leading to high yields at low reaction temperatures. The stability after the addition of chlorine promoters implies a substantial improvement over the industrial practice: a single pretreatment step at ambient pressure suffices in contrast with the common practice of continuously feeding organochlorinated precursors during the reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

In situ temperature measurements in microwave-heated gassolid catalytic systems. Detection of hot spots and solid-fluid temperature gradients in the ethylene epoxidation reaction

  • Ramírez, A.
  • Hueso, J.L.
  • Mallada, R.
  • Santamaria, J.
Infrared thermographic techniques have been used for the first time to determine real-time gas and solid temperatures, as well as gas- solid temperature gradients in microwave heated structured reactors. A special reactor vessel has been developed that allows direct observation of the catalyst under microwave heating, and an operating procedure is presented to obtain gas and solid apparent emissivities as a function of temperature. These values are thereafter used to calculate temperatures at any point in the gas and solid phases under reaction. The method has been used to obtain gas and solid temperatures during the ethylene epoxidation reaction carried out on a silver-copper oxide catalyst. The direct heating of the monolith walls produced a stable, large temperature gradient between the solid and the gas phase.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Extraordinary sensitizing effect of co-doped carbon nanodots derived from mate herb: application to enhanced photocatalytic degradation of chlorinated wastewater compounds under visible light

  • Ortega-Liebana, M. Carmen
  • Hueso, José L.
  • Ferdousi, Shammi
  • Arenal, Raul
  • Irusta, Silvia
  • Yeung, King L.
  • Santamaria, Jesus
tThe present work investigates the role of two types of carbon nanodots (CNDs) as novel sensitizers of TiO2to create a visible-light driven photo-catalyst that is not only efficient for solar-driven pollution abate-ment, but also inexpensive, durable and environmentally-friendly. Two widely available green organicprecursors, the Argentinean herb Mate and the Stevia plant have been selected as the carbogenic sourceto thermally induce the formation of different types of CNDs with different levels of N and P doping andtunable photoluminescence response in the UV–vis-near infrared (NIR) ranges. These CNDs have beensuccessfully assembled with TiO2to form heterogeneous photocatalysts that are highly active in thevisible-light and NIR- driven photodegradation of 2,4-dichlorophenol (2,4-DCP), a persistent chlorinatedorganic compound present in numerous pesticide formulations.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Uniform luminescent carbon nanodots prepared by rapid pyrolysis of organic precursors confined within nanoporous templating structures

  • Ortega-Liebana, M.
  • Chung, N. X.
  • Limpens, R.
  • Gomez, L.
  • Hueso, J. L.
  • Santamaria, J.
  • Gregorkiewicz, T.
Although several methods on the preparation of carbon nanodots (CNDs) emitting throughout the visible have been recently reported, in most of the processes the product suffers from inhomogeneity in size and shape limiting their impact. Here, we report the synthesis of undoped and nitrogen-doped luminescent carbon nanodots by rapid pyrolysis using ordered mesoporous silica nanorods as confining templates. A rapid thermal decomposition (pyrolysis) within the confined dimensions of their pores leads to a highly uniform size distribution of CNDs with average sizes below 4 nm. These CNDs are synthesized in an extremely short time period (5 min of reaction) by immersion in a fluidized-bed reactor that provides heating homogeneity and ensures fast heat transfer. In addition, a rapid release of the homogeneous CNDs can be easily achieved by a simple ultrasonication-filtration step that prevents further chemical action on the mesoporous templates. The emission of both undoped and N-doped CNDs in colloidal and solid state (with an efficiency of 1–5%) originates from a combination of quantum confinement effects and the presence of oxidized surface states; N-doping introduces resonant absorption states which participate in emission. Furthermore, we present a simple model to describe the excitation-dependent/-independent mechanism of carbon nanodots.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

In-situ preparation of ultra-small Pt nanoparticles within rod-shaped mesoporous silica particles: 3-D tomography and catalytic oxidation of n-hexane

  • Uson, Laura
  • Hueso, José L.
  • Sebastian, Víctor
  • Arenal, Raul
  • Florea, Ileana
  • Irusta, Silvia
  • Arruebo, Manuel
  • Santamaria, Jesús
The shape and porous configuration of supports are key parameters to design outstanding catalysts. However, the selection of a proper mesoporous support, such as SBA-15, by itself does not guarantee accessibility to catalytic sites. The distribution of the active phase and its stability are strongly related to the procedure used to deposit it on the catalytic substrate. Herein, we have prepared rod-shaped SBA-15 silica supports functionalized with amine groups to facilitate the electrostatic attraction and a good distribution of the resulting Pt-based catalytic nanoparticles along the pore walls. Additionally, the use of tetrakis-(hydroxymethyl)-phosphonium chloride (THPC) as both reductant and stabilizer is presented as a novel alternative for Pt nanoparticle synthesis. The behaviour of this catalyst in the total oxidation of n-hexane demonstrates high activity and excellent stability after 70 h on reaction stream. STEM-HAADF and 3-D tomography were used to confirm the presence of the metallic nanoparticles within the mesochannels and to corroborate their reduced sintering after reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Luminescent mesoporous nanorods as photocatalytic enzyme-like peroxidase surrogates

  • Ortega-Liebana, M.Carmen
  • Hueso, Jose L.
  • Fernandez-Pacheco, Rodrigo
  • Irusta, Silvia
  • Santamaria, Jesus
Herein we report on a novel inorganic peroxidase-mimicking nanocatalyst activated under blue LED photoirradiation. A novel flash-pyrolysis method has been developed for the generation of strong blue photoluminescence (PL) centers attributed to silicon and carbon-based sites within a mesoporous SBA-15 silica nanorod platform. The type of centers and their PL response can be controlled by varying the flash thermal treatment conditions. By tailoring the operating conditions the system can be driven towards the preferential generation of carbon-based luminescent centers, with or without the simultaneous generation of silicon-based centers. The properties and the nature of these luminescent centers within the mesoporous nanorods have been thoroughly corroborated by a battery of characterization techniques including fluorescence spectroscopy, X-ray photoelectron spectroscopy (XPS) and electron energy loss spectroscopy (EELS) at the local level of the structures combined with scanning transmission electron microscopy (STEM) imaging. In addition, these luminescent mesoporous nanorods have been successfully tested as robust photocatalysts able to display peroxidase-like activity and indirect glucose sensing in a wider range of pH conditions compared to the natural enzyme, especially when carbogenic dots and oxygen-deficient silica centers are simultaneously present in the structure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Escaping undesired gas-phase chemistry: Microwave-driven selectivity enhancement in heterogeneous catalytic reactors

  • Ramirez, A.
  • Hueso, J.L.
  • Abian, M.
  • Alzueta, M.U.
  • Mallada, R.
  • Santamaria, J.
Research in solid-gas heterogeneous catalytic processes is typically aimed toward optimization of catalyst composition to achieve a higher conversion and, especially, a higher selectivity. However, even with the most selective catalysts, an upper limit is found: Above a certain temperature, gas-phase reactions become important and their effects cannot be neglected. Here, we apply a microwave field to a catalyst-support ensemble capable of direct microwave heating (MWH). We have taken extra precautions to ensure that (i) the solid phase is free from significant hot spots and (ii) an accurate estimation of both solid and gas temperatures is obtained. MWH allows operating with a catalyst that is significantly hotter than the surrounding gas, achieving a high conversion on the catalyst while reducing undesired homogeneous reactions. We demonstrate the concept with the CO 2 -mediated oxidative dehydrogenation of isobutane, but it can be applied to any system with significant undesired homogeneous contributions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Green synthesis of a Cu/SiO2 catalyst for efficient H2-SCR of NO

  • Gioria, Esteban
  • Marchesini, F. Albana
  • Soldati, Analia
  • Giorello, Antonella
  • Hueso, José L.
  • Gutiérrez, Laura
In this work, the synthesis of Cu/SiO2 catalysts starting frompre-formed copper nanoparticle (CuNP) colloidal suspensions was carried out. Two different protocols for the CuNP synthesis were tested: (i) a green approach using water as solvent and ascorbic acid as reducer and stabilizing agent, and (ii) a second solvothermal method involving the use of diethylene glycol as solvent, sodium hypophosphite (NaH2PO2) as reducer, and polyvinylpyrrolidone (PVP) and cetyltrimethylammonium bromide (CTAB) as stabilizing agents. In addition, and for the sake of comparison, a third catalyst was prepared by solid state conventional grinding of CuO with SiO2. The catalysts were tested in the environmentally relevant catalytic reduction of NOX with H2, in a temperature range from 300 to 500 °C. The catalysts were characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR) cycles, Raman spectroscopy, and N2 adsorption for specific surface BET measurements. From these techniques CuO and Cu(0) species were detected depending on the synthesis protocol. CuNP size and size distribution in the colloid suspensions were determined by transmission electronic microscopy (TEM). The catalyst prepared from the aqueous suspension (CuAsc/SiO2) exhibited higher NO conversion (100%) and selectivity (85%) toward N2 at the lower reaction evaluated temperature (300 °C). The CuCTAB/SiO2 catalyst obtained by the solvothermal approach showed activity at high reaction temperature (400 °C) preferentially. The metal-support mechanical mixture exhibited a negligible response at low temperature and low conversion (68%) and selectivity (88%) at 500 °C. Nanoparticle size and distribution on the support, together with the metal-support interaction, were postulated as the most plausible parameters governing the catalytic performance of the different Cu/SiO2 materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Upconverting Carbon Nanodots from EDTA as Near-Infrared Activated Phototheranostic Agents

  • Ortega-Liebana, M.C.
  • Encabo-Berzosa, M.M.
  • Casanova, Á
  • Pereboom, M.D.
  • Alda, O.
  • Hueso, J.L.
  • Santamaría, J.
This work describes the synthesis of nitrogen-doped carbon nanodots (CNDs) synthesized from ethylene diamine tetra acetic acid (EDTA) as a precursor and their application as luminescent agents with a dual-mode theranostic role as near-infrared (NIR) triggered imaging and photodynamic therapy agents. Interestingly, these fluorescent CNDs are more rapidly and selectively internalized in tumor cells and exhibit no cytotoxicity until remotely activated with a NIR illumination source. These CNDs are excellent candidates for photo-theranostic purposes, i.e.: simultaneous imaging and therapy can be carried out on cancer cells using their luminescent properties and the in situ generation of reactive oxidative species (ROS) upon excitation in the NIR range. In the presence of CNDs NIR remote activation induces the in vitro killing of U251 MG cells. Through the use of flow imaging cytometry we have been able to successfully map and quantify the different type of cell deaths induced by the presence of intracellular superoxide anions (¿O2-) and hydrogen peroxide (H2O2) ROS species generated in situ upon NIR irradiation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microwave-activated structured reactors to maximize propylene selectivity in the oxidative dehydrogenation of propane

  • Ramírez, Adrián
  • Hueso, José Luis
  • Mallada, Reyes
  • Santamaría, Jesús
Microwave (MW) heating has been applied to increase the selectivity to propylene in the oxidative dehydrogenation (ODH) of propane. The preferential heating of the solid monolith (made of SiC, a good microwave susceptor), allows working with a lower gas phase temperature, reducing the formation of undesired by-products in the gas phase via homogeneous reactions. Conversion levels of ~ 21% and selectivity to propylene up to 70% have been achieved with MW-heated straight channel monolithic reactors coated with a VMgO catalyst. These competitive values contrast with the more limited performance delivered by the same catalytic system when it is subjected to conventional heating in a fixed-bed reactor configuration, thereby corroborating the advantage of working under a significant gas–solid temperature gap to minimize the extent of homogeneous reactions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Contribución de congreso (ConferenceOutput)

Titania-coated gold nanorods with expanded photocatalytic response. Enzyme-like glucose oxidation under near-infrared illumination

  • Ortega-Liebana, M.C.
  • Hueso Martos, José Luis
  • Arenal, R.
  • Santamaria, J.
Gold nanorods coated with a uniform titanium dioxide nanoshell have been prepared and used as glucose-oxidase surrogates. Remarkably, this core-shell photocatalytic nanostructure has been able to induce complete oxidation of glucose at near room temperature (32-34 °C) in a wide range of pH values with the aid of a near-infrared (NIR) irradiation source. In contrast, the uncoated gold nanorods exhibit negligible photo-oxidation response under identical experimental conditions thereby proving the photoactivity of the titania shell towards glucose oxidation. The process takes place via in situ photo-generation of singlet oxygen or hydroxyl radicals as reactive oxidative species (ROS). This underlines the role played by the core nanorods as plasmonic light harvesters in the NIR range and constitutes the first example of a NIR-activated enzyme-like catalyst.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Nitrogen-doped luminescent carbon nanodots for optimal photo-generation of hydroxyl radicals and visible-light expanded photo-catalysis

  • Ortega-Liébana, M.
  • Hueso, J. L.
  • Ferdousi, S.
  • Yeung, K. L.
  • Santamaría, Jesús
Luminescent carbon nanodots (CNDs) have been obtained by hydrothermal processing of ascorbic acid (AA) and ethanolamine (EN). The resulting N-doped carbon nanostructures exhibit interesting and tunable emission capabilities with a dual behavior as down-converters and more importantly, as up-converting quantum dots. Herein, we also evaluate the optical response of these CNDs to selectively generate highly reactive oxidative hydroxyls (OH) upon irradiation with different light-emitting diodes (LEDs) in the visible-NIR range. Finally, the role of the N-doped CNDs as nano-sensitizers to maximize the solar light harvesting and expand the photo-catalytic response of a commonly used UV-active catalyst such as TiO2 was successfully tested in the degradation of an organo-chlorinated compound under visible light.