Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Design of sustainable aquafeed for freshwater and marine Recirculating Aquaculture Systems

  • Fanizza, Cecilia
[ES] Esta tesis doctoral investiga la optimización de piensos acuáticos personalizados para sistemas acuícolas recirculantes marinos y de agua dulce (RAS), examinando el potencial de varios ingredientes. Evalúa las características de las materias primas, la digestibilidad, las propiedades de los piensos y los desechos, el rendimiento de los peces, la salud, la calidad de los filetes y la viabilidad económica. Los resultados se analizan a través de un análisis SWOT, que evalúa las fortalezas, debilidades, oportunidades y amenazas de los ingredientes dietéticos probados. El primer estudio examina la digestibilidad de las materias primas, las características de los pellets, las propiedades fecales y la excreción de nitrógeno en el jurel mayor (Seriola dumerili) en RAS. Los resultados muestran que la hemoglobina porcina, la harina de pescado, el concentrado de proteína de soja y la levadura de cerveza con grasa presentaron la mayor digestibilidad, mientras que la levadura de cerveza sin grasa y la pulpa de remolacha mostraron la menor. La harina de pescado mostró la mayor fuga de aceite, y la pulpa de remolacha la menor. Estos hallazgos respaldan la formulación sostenible de piensos acuáticos para el jurel mayor. El segundo estudio explora las estrategias de manejo de residuos en RAS para la trucha arcoíris (Oncorhynchus mykiss). Las dietas con diferentes fuentes de harina de pescado y proteínas alternativas indicaron que la harina de subproductos avícolas mejoró la digestibilidad de los nutrientes, mientras que la harina de plumas hidrolizada y la harina de colza redujeron la digestibilidad, pero tuvieron un impacto positivo en la calidad del agua. El estudio destaca el equilibrio entre la digestibilidad y la calidad del agua en la formulación de piensos. El tercer estudio investiga los efectos de diversas mezclas de harina de pescado y proteínas derivadas de aves sobre el pez gato africano (Clarias gariepinus). Una dieta con mayor contenido de proteínas avícolas redujo la digestibilidad y el rendimiento de crecimiento, mientras que una dieta equilibrada con harina de pescado y proteínas derivadas de aves favoreció el crecimiento óptimo. Esto sugiere que un reemplazo moderado de la harina de pescado por subproductos avícolas podría ser una estrategia viable. El análisis SWOT condujo al desarrollo de un marco de toma de decisiones basado en el análisis bibliométrico, presentando una pirámide de priorización para la selección de ingredientes en los piensos acuáticos para RAS. Revela un cambio en las prioridades de la industria hacia la calidad del agua y el abastecimiento sostenible de ingredientes, lo que refleja la alineación con los objetivos de sostenibilidad ambiental, mientras que los estándares regulatorios se han estabilizado. Este marco ofrece una guía para desarrollar piensos acuáticos sostenibles y eficientes en recursos, adaptados a RAS., [CA] Aquesta tesi doctoral investiga l'optimització d'aliments aquàtics personalitzats per a sistemes aqüícoles recirculants marins i d'aigua dolça (RAS), examinant el potencial de diversos ingredients. Avalua les característiques de les matèries primeres, la digestibilitat, les propietats de l'aliment i els residus, el rendiment dels peixos, la salut, la qualitat dels lloms i la viabilitat econòmica. Els resultats s'analitzen a través d'una anàlisi SWOT, que avalua els punts forts, febleses, oportunitats i amenaces dels ingredients dietètics provats. El primer estudi examina la digestibilitat de les matèries primeres, les característiques dels pellets, les propietats fecals i l'excreció de nitrogen en el jurel major (Seriola dumerili) en RAS. Els resultats mostren que l'hemoglobina porcina, la farina de peix, el concentrat de proteïna de soja i el llevat de cervesa amb greix van presentar la major digestibilitat, mentre que el llevat de cervesa sense greix i la polpa de remolatxa van mostrar la més baixa. La farina de peix va mostrar la major fuita d'oli, i la polpa de remolatxa la més baixa. Aquests resultats donen suport a la formulació sostenible d'aliments aquàtics per al jurel major. El segon estudi explora les estratègies de gestió de residus en RAS per a la truita de riu (Oncorhynchus mykiss). Les dietes amb diferents fonts de farina de peix i proteïnes alternatives van indicar que la farina de subproductes avícoles va millorar la digestibilitat dels nutrients, mentre que la farina d'ales hidrolitzada i la farina de colza van reduir la digestibilitat, però van tenir un impacte positiu en la qualitat de l'aigua. L'estudi destaca l'equilibri entre la digestibilitat i la qualitat de l'aigua en la formulació de pinsos. El tercer estudi investiga els efectes de diverses mescles de farina de peix i proteïnes derivades d'aus sobre el peix gat africà (Clarias gariepinus). Una dieta amb un major contingut de proteïnes avícoles va reduir la digestibilitat i el rendiment de creixement, mentre que una dieta equilibrada amb farina de peix i proteïnes derivades d'aus va afavorir el creixement òptim. Això suggereix que un reemplaçament moderat de la farina de peix per subproductes avícoles podria ser una estratègia viable. L'anàlisi SWOT va conduir al desenvolupament d'un marc de presa de decisions basat en l'anàlisi bibliomètrica, presentant una piràmide de priorització per a la selecció d'ingredients en els aliments aquàtics per a RAS. Revela un canvi en les prioritats de la indústria cap a la qualitat de l'aigua i l'obtenció sostenible d'ingredients, reflectint una alineació amb els objectius de sostenibilitat ambiental, mentre que els estàndards reguladors s'han estabilitzat. Aquest marc ofereix una guia per a desenvolupar aliments aquàtics sostenibles i eficients en recursos, adaptats a RAS., [EN] This PhD thesis investigates the optimization of tailored aquafeeds for marine and freshwater recirculating aquaculture systems (RAS), examining the potential of various ingredients. It evaluates raw material characteristics, digestibility, feed and waste properties, fish performance, health, fillet quality, and economic feasibility. The findings are analysed through a SWOT analysis, which assesses the strengths, weaknesses, opportunities, and threats of the tested dietary ingredients. The first study examines raw material digestibility, pellet characteristics, faecal properties, and nitrogen excretion in greater amberjack (Seriola dumerili) in RAS. Results show that porcine haemoglobin, fishmeal, soybean protein concentrate, and brewer's yeast with fat had the highest digestibility, while brewer's yeast without fat and beet pulp showed the lowest. Fishmeal exhibited the highest oil leakage, and beet pulp had the lowest. These findings support sustainable aquafeed formulation for greater amberjack. The second study explores waste management strategies in RAS for rainbow trout (Oncorhynchus mykiss). Diets with varying fishmeal and alternative protein sources indicated that poultry by-product meal improved nutrient digestibility, while hydrolysed feather meal and rapeseed meal reduced digestibility but positively impacted water quality. The study highlights the balance between digestibility and water quality in feed formulation. The third study investigates the effects of varying fishmeal and poultry-derived protein blends on African catfish (Clarias gariepinus). A diet with higher poultry protein content reduced digestibility and growth performance, while a balanced diet with fishmeal and poultry-derived proteins supported optimal growth. This suggests that moderate fishmeal replacement with poultry by-products could be a viable strategy. The SWOT analysis led to the development of a decision-making framework based on bibliometric analysis, presenting a prioritization pyramid for ingredient selection in RAS aquafeeds. It reveals a shift in industry priorities toward water quality and sustainable ingredient sourcing, reflecting alignment with environmental sustainability goals, while regulatory standards have stabilized. This framework offers a guide for developing resource-efficient, sustainable aquafeeds tailored to RAS., Thesis written with the financial contribution of PON Ricerca e Innovazione 2014-2020 (DM 1061/2021; CCI 2014IT16M2OP005), risorse FSE REACT-EU, Azione IV.5 <Dottorati su tematiche Green= (Ministero dell'Università e della Ricerca; CUP: C95F21007670007) and submitted in January 2025
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Inter-laboratory study on the influence of 3D concrete printing set-ups on the bond behaviour of various reinforcements

  • Gebhard, Lukas
  • Esposito, Laura
  • Menna, Costantino
  • Mata Falcon, Jaime|||0000-0001-8701-4410
[EN] This study investigates the influence of different printing set-ups and materials on the bond strength of reinforcement manually placed between 3D printed concrete layers. An identical experimental campaign was performed at two institutes in Switzerland and Italy. Each institute used its own printing process, which consisted either of a set on-demand mix or a high yield stress material. Two types of reinforcement (reinforcing bar Ø8 mm and a high strength steel wire Ø1 mm) and three production configurations (casting and printing with the reinforcement parallel or perpendicular to the printing direction) were investigated. The results showed high bond strength with only a limited influence of the fabrication method for the reinforcing bars. An increased bond was observed for the set on-demand approach compared to the high yield strength material. The comparison with existing models showed that the reinforcing bar bond strength of printed concrete varies slightly from conventional concrete. The high strength wires exhibited poor bond. Based on the gathered experiences, insights into the standardisation of testing for 3D concrete printing are discussed., The authors would like to thank the team of Etesias (Napoli, Italy) and Ana Anton (Digital Building Technologies, ETH Zurich) and Lex Reiter (Chair of Physical Chemistry of Building Materials, ETH Zurich) for their support in the printing laboratory. Furthermore, the authors are grateful for the support of the two teams of the structural labs at both institutes. At ETH Zurich, the experimental campaign was funded, and the exchange was supported by the Swiss National Science Foundation, within the National Centre for Competence in Research in Digital Fabrication (project number 51NF40-141853) . At UniNa, the experi-mental activities were supported by Italcementi Heidelberg CementGroup (industrial partner of the PhD program) and by the Italian Ministry of University and Research (MIUR) under program PON 2014-2020 (CCI 2014IT16M2OP005) . A special thanks for enabling the exchange and supporting the research goes to Prof. Dr. Walter Kaufmann (ETH Zurich).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The secret of secrets: carbonic anhydrase concentration in lizards' femoral gland secretions is tuned to environmental conditions

  • Mangiacotti, Marco
  • Fumagalli, Marco
  • Moreno-Rueda, Gregorio
  • Zamora-Camacho, Francisco J.
  • Martín, José
  • Sacchi, Roberto
Among the modalities of animal communication, the chemical channel is the only one that allows signalers and receivers to communicate without being necessarily in the same place at the same time. This asynchrony may influence signal design, as its effectiveness depends on adapting to predictable environmental conditions. Many lizard species scent-mark territories by depositing waxy secretions made of protein-lipid mixtures from specialized epidermal glands. These secretions, once left on a substrate, face environmental fluctuations, and their lifespan depends on the mixture's ability to tolerate such changes. Since some proteins in these secretions are enzymes, we hypothesize they may serve homeostatic functions, enabling the mixture to actively respond to external conditions. Accordingly, we can expect that (1) enzymes remain active in secretions; and (2) their abundance varies across an environmental gradient, tuning the homeostatic ability to the predictable external conditions. We tested these predictions using carbonic anhydrase (CA), an enzyme found in many lizard secretions that regulates pH by catalyzing the reaction between water and carbon dioxide. Protonography confirmed CA activity in proteins extracted from femoral gland secretions from eight Podarcis lizard species and Psammodromus algirus. We also analyzed CA abundance in males (N = 70) from 12 Ps. algirus populations, and its correlation with the environmental gradient (geography, topography, climate). Model comparison revealed a credible relationship between CA concentration and geography as well as bioclimatic variables in Ps. algirus. Taken together, these findings suggest CA plays an enzymatic function that may help stabilize the internal chemical environment of secretions, potentially enhancing the scent-mark's lifespan and effectiveness under varying environmental conditions., Fondo Sociale Europeo REACT EU; Programma Operativo Nazionale Ricerca e Innovazione 2014-2020; Italian Ministry for University and Research (MUR); Universita di Pavia; Wiley; CRUI-CARE
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Photoplethysmogram Signal Morphology-Based Stress Assessment

  • Rinkevicius, M.
  • Kontaxis, S.
  • Gil, E.
  • Bailon, R.
  • Lázaro, J.
  • Laguna, P.
  • Marozas, V.
Stress is a healthy natural response to a perceived or actual threat. However, when stress is persistent, it may decrease work productivity, increase the risk of diseases, and affect the quality of life. Stress is reflected in physiological variables, such as heart rate, blood pressure, and pulse wave velocity among others. A photoplethys-mogram (PPG) contains information related to pulse rate and blood pressure. This study analyses parameters derived from PPG signal morphology for mental stress assessment.A low-complexity algorithm is designed using bandpass filtered higher-order derivatives of the PPG signal for estimation of six morphological parameters: the forward pulse wave amplitude A1, the systole and diastole durations T1 and Td, the time delays of reflected waves T12 and T13 from the renal and iliac sites in the central arteries, and the pulse duration Tp. The parameters were investigated on a set of 18 healthy subjects by using a modified Trier Social Stress Test.The results show that the most sensitive PPG morphology parameters to mental stress are the amplitude of forward wave A1, the duration of diastole Td, the time delay of the reflected wave T13, and the pulse-to-pulse interval Tp.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Autonomic Nervous System Response to Heat Stress Exposure by Means of Heart Rate Variability

  • Kontaxis, S.
  • Bailon, R.
  • Rapalis, A.
  • Brazaitis, M.
  • Cernych, M.
  • Lazaro, J.
  • Laguna, P.
  • Gil, E.
  • Marozas, V.
In this study, a heart rate variability (HRV) analysis guided by respiration is conducted to assess changes in autonomic nervous system (ANS) regulation during pronounced heat stress induced by repetitive exposures to dry sauna in 13 young healthy subjects. The spectral power at the low frequency (LF) band [0.04, 0.15] Hz and at the high frequency band centered around the mean respiratory rate, estimated from ECG-derived respiration signals, are studied. The mean heart rate (HR), the total power of HRV, and the normalized LF power are also analyzed.Results show that mean HR and normalized LF power increase significantly after basal stage, not only during the sauna sessions, but also at the intermediate short rest stages and recovery phase after 30 min. A significant reduction in the total power of HRV during all sauna sessions is observed, while an increased power in LF band is shown only during recovery which might be related to improved cardiac function (increased cardiac output and reduced peripheral vascular resistance) after heat exposure. Respiratory rate does not change significantly during the protocol but a negative trend at stress stages may indicate a reverse reaction against an over-activation of the sympathetic branch. In conclusion, exposure to heat stress shifts sympathovagal balance of ANS toward sympathetic dominance that increases HR and diminishes HRV.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High oxygen and SNG injection in blast furnace ironmaking with Power to Gas integration and CO2 recycling

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begona
  • Romeo, Luis M.
  • Eveloy, Valerie
In the last years, reduction of CO2 emissions from the steel industry has been of great importance. Carbon capture, oxygen blast furnaces and top gas recycling technologies, among others, have been deeply studied as low carbon solutions. In this paper, a novel integration of carbon capture and power to gas technologies in the steelmaking industry is presented. Green hydrogen via proton exchange membrane (PEM) electrolysis and CO2 via methyldiethanolamine (MDEA) scrubbing from the blast furnace gas (BFG) are used to produce synthetic natural gas in an isothermal fixed bed methanation plant. The latter gas is injected into the blast furnace, closing a carbon loop and reducing coal consumption. The oxygen by-produced in the electrolyser covers the entire oxygen demand of the steelmaking plant and avoids the need for an air separation unit (ASU). The novelty of this work relies on the variation of the oxygen enrichment and its temperature in the hot blast, and how it influences the power to gas integration concept. This power to gas integration is compared with a conventional BF-BOF plant from a technical, economic, energy and environmental point of view. Both plant process configurations were implemented in Aspen Plus simulations, assessing the fossil fuel demand, energy penalty, cost and CO2 emissions. Emission reduction up to 34% can be achieved with power to gas integration, with an energy penalty of 17 MJ/tHM and a cost of 352 €/tCO2.