Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

CO2 recycling in the iron and steel industry via power-to-gas and oxy-fuel combustion

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Romeo, Luis M.
  • Peña, Begoña
  • Eveloy, Valerie
The iron and steel industry is the largest energy-consuming sector in the world. It is responsible for emitting 4-5% of the total anthropogenic CO2. As an energy-intensive industry, it is essential that the iron and steel sector accomplishes important carbon emission reduction. Carbon capture is one of the most promising alternatives to achieve this aim. Moreover, if carbon utilization via power-to-gas is integrated with carbon capture, there could be a significant increase in the interest of this alternative in the iron and steel sector. This paper presents several simulations to integrate oxy-fuel processes and power-to-gas in a steel plant, and compares gas productions (coke oven gas, blast furnace gas, and blast oxygen furnace gas), energy requirements, and carbon reduction with a base case in order to obtain the technical feasibility of the proposals. Two different power-to-gas technology implementations were selected, together with the oxy blast furnace and the top gas recycling technologies. These integrations are based on three strategies: (i) converting the blast furnace (BF) process into an oxy-fuel process, (ii) recirculating blast furnace gas (BFG) back to the BF itself, and (iii) using a methanation process to generate CH4 and also introduce it to the BF. Applying these improvements to the steel industry, we achieved reductions in CO2 emissions of up to 8%, and reductions in coal fuel consumption of 12.8%. On the basis of the results, we are able to conclude that the energy required to achieve the above emission savings could be as low as 4.9 MJ/kg CO2 for the second implementation. These values highlight the importance of carrying out future research in the implementation of carbon capture and power-to-gas in the industrial sector. © 2021 by the authors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Synthetic natural gas production in a 1 kW reactor using Ni–Ce/Al2O3 and Ru–Ce/Al2O3: Kinetics, catalyst degradation and process design

  • Bailera, M.
  • Lisbona, P.
  • Peña, B.
  • Alarcón, A.
  • Guilera, J.
  • Perpiñán, J.
  • Romeo, L. M.
Nickel and ruthenium promoted by ceria were compared as catalyst active phase for the production of synthetic natural gas in a 1 kW fixed-bed reactor (49 cm in length and 3 cm in diameter). Both catalysts were tested in a broad range of conditions: 250–450 °C, 8000–16000 h−1 GHSV, 3.5–5.5H2/CO2 ratio, and atmospheric pressure. The Ni-based catalyst presented higher CO2 conversion and lower reduction of BET area and metal dispersion after utilization. Two kinetic models were elaborated according to the performance of the catalysts in this reactor. The minimum mean squared error between the kinetic model and experiments was 3.0% for the Ru-based catalyst and 1.4% for the Ni-based catalyst. The kinetic model of the Ni-based catalyst was implemented in Aspen Plus to evaluate potential methanation plant designs. The simulation minimized the amount of catalyst required to reach 95 vol% of CH4, within proper technical limits (GHSV 5000 h−1 and temperature 300 °C). The 3-reactor plant was the most adequate configuration. The total catalyst mass was 3.26 kg per kg/h of SNG, the heat removed from the reactors was 10.8 MJ/kgSNG, and the preheating necessity was 4.90 MJ/kgSNG. The electrolysis energy consumption was 86.4 MJ/kgSNG.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Revisiting the Rist diagram for predicting operating conditions in blast furnaces with multiple injections

  • Bailera, Manuel
  • Nakagaki, Takao
  • Kataoka, Ryoma
Background: The Rist diagram is useful for predicting changes in blast furnaces when the operating conditions are modified. In this paper, we revisit this methodology to provide a general model with additions and corrections. The reason for this is to study a new concept proposal that combines oxygen blast furnaces with Power to Gas technology. The latter produces synthetic methane by using renewable electricity and CO2 to partly replace the fossil input in the blast furnace. Carbon is thus continuously recycled in a closed loop and geological storage is avoided. Methods: The new model is validated with three data sets corresponding to (1) an air-blown blast furnace without auxiliary injections, (2) an air-blown blast furnace with pulverized coal injection and (3) an oxygen blast furnace with top gas recycling and pulverized coal injection. The error is below 8% in all cases. Results: Assuming a 280 tHM/h oxygen blast furnace that produces 1154 kgCO2/tHM, we can reduce the CO2 emissions between 6.1% and 7.4% by coupling a 150 MW Power to Gas plant. This produces 21.8 kg/tHM of synthetic methane that replaces 22.8 kg/tHM of coke or 30.2 kg/tHM of coal. The gross energy penalization of the CO2 avoidance is 27.1 MJ/kgCO2 when coke is replaced and 22.4 MJ/kgCO2 when coal is replaced. Considering the energy content of the saved fossil fuel, and the electricity no longer consumed in the air separation unit thanks to the O2 coming from the electrolyzer, the net energy penalizations are 23.1 MJ/kgCO2 and 17.9 MJ/kgCO2, respectively. Discussion: The proposed integration has energy penalizations greater than conventional amine carbon capture (typically 3.7 – 4.8 MJ/kgCO2), but in return it could reduce the economic costs thanks to diminishing the coke/coal consumption, reducing the electricity consumption in the air separation unit, and eliminating the requirement of geological storage.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Limits on the integration of power to gas with blast furnace ironmaking

  • Bailera, Manuel
  • Nakagaki, Takao
  • Kataoka, Ryoma
This article compares 16 Power to Gas integrations for blast furnace ironmaking by using 17 key performance indicators. The study includes 4 types of PtG (PtH2, PtSNG using pure CO2, PtSNG using treated BFG, and PtSNG using BFG), two types of blast furnaces (air-blown and oxygen) and two types of fossil replacement (coal or coke). The blast furnaces are modelled using the Rist diagram, validated with literature data (<2% deviation). For most cases, the decrease in total CO2 emissions is around 150–215 kgCO2/tHM per MW/(tHM/h) of electrolysis. The energy penalty (in terms of electricity consumption) was found to be mostly independent on the size of the PtG plant, but greatly dependent on the type of integration (10.1–20.6 MJ/kgCO2). If significant CO2 reductions are aimed, self-sufficiency in electricity consumption will not be achieved. In practice, the maximum PtG capacity to install is limited by the decrease in the flame temperature. In this context, the PtSNG integration consuming treated BFG, applied to OBF for coal replacement, provides the best results. Assuming a 500 tHM/h blast furnace, the PtG capacity of this concept could be as large as 490 MW and avoid up to 21% of the CO2 emissions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Extending the Operating Line Methodology to Consider Shaft and Preheating Injections in Blast Furnaces

  • Bailera, Manuel
  • Nakagaki, Takao
  • Kataoka, Ryoma
In the last years, the injection of reducing gases in the shaft and preparation zone of the blast furnace has been proposed as a decarbonization option, mainly associated to oxyfuel blast furnaces and top gas recycling configurations. However, the Rist diagram, which is one of the preferred methodologies to characterize the operation of blast furnaces, is not valid to evaluate these new decarbonization options. In this article we propose a generalization of the operating line methodology to extend its applicability to scenarios of variable molar flows along the blast furnace (i.e., shaft and preheating injections) and non-continuous oxidation profiles (presence of CO2 and H2O in the injected gases). The extended operating line methodology was implemented in an Aspen Plus simulation, which provides a detailed modelling of the preparation zone, the thermal reserve zone, the lower zone and the raceways. The simulation was used to validate the generalized operating line methodology through three different data sets: (i) an air-blown blast furnace with pulverized coal injection and O2 enrichment, (ii) an oxyfuel blast furnace with shaft gas injection, and (iii) an oxyfuel blast furnace with preheating gas injection in the preparation zone. In general, the discrepancy between the reference data and the simulation results is well below 3.5%, so the extended operating line methodology is considered validated.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Integration of carbon capture technologies in blast furnace based steel making: a comprehensive and systematic review

  • Perpiñán, J.
  • Peña, B.
  • Bailera, M.
  • Eveloy, V.
  • Kannan, P.
  • Raj, A.
  • Lisbona, P.
  • Romeo, L. M.
Decarbonization of the iron and steel industry, which accounts for 7–9% of global annual emissions, is a strategic objective to achieve carbon emissions reduction targets in line with climate change policies, while maintaining economic competitiveness. Carbon capture (CC) technologies are of critical importance to achieve these goals. This work presents the first systematic review of the integration of CC technologies in the blast furnace-basic oxygen furnace (BF-BOF) steelmaking route, which is expected to maintain a dominant market share over the coming decades. Integration options for post-combustion, looping cycles, oxy-combustion and pre-combustion are described and compared in terms of energy penalty, carbon emissions abatement potential, cost, technology readiness level, and practical deployment considerations. The review yielded 188 studies from peer-reviewed articles and technical papers. Research is mainly focused on chemical absorption, physical adsorption, and oxy-blast furnace technologies, but other carbon capture methods including calcium looping, Sorption Enhanced Water Gas Shift, and membranes appear promising in terms of cost and carbon emission reduction. This article provides an in-depth analysis of the current state of the art and crucial considerations for future decision making in the techno-economic selection and integration of CC technologies. Barriers to overcome for practical implementation are also identified and discussed in this article.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Comparing different syngas for blast furnace ironmaking by using the extended operating line methodology

  • Bailera, Manuel
This paper assesses the injection of different syngas in air-blown blast furnaces, oxygen blast furnaces, and advanced oxygen blast furnaces. The selected types of syngas come from biomass gasification, plastic gasification, CO2 electrolysis, and reverse water–gas shift reaction. An Aspen Plus model, based on the new extended operating line methodology, was used for the simulation. This methodology is a generalization of the conventional Rist diagram, to extend its application to cases in which the injected gases have large contents of CO2 and H2O, and also to cases in which injections take place at the middle or upper zone of the blast furnace. The base cases were elaborated and validated with data from literature, with a discrepancy below 3.5%. A total of 7 key performance indicators were defined for the study (mass flow of syngas, coke replacement ratio, gas utilization, percentage of direct reduction, blast furnace gas temperature, flame temperature, and net CO2 emissions). In practice, the amount of syngas that can be injected is limited to 92 – 264 kgsyngas/tHM because of the drop in the flame temperature. The lowest net CO2 emissions are achieved in oxygen blast furnace with injection of syngas from reverse water–gas shift reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High oxygen and SNG injection in blast furnace ironmaking with Power to Gas integration and CO2 recycling

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begona
  • Romeo, Luis M.
  • Eveloy, Valerie
In the last years, reduction of CO2 emissions from the steel industry has been of great importance. Carbon capture, oxygen blast furnaces and top gas recycling technologies, among others, have been deeply studied as low carbon solutions. In this paper, a novel integration of carbon capture and power to gas technologies in the steelmaking industry is presented. Green hydrogen via proton exchange membrane (PEM) electrolysis and CO2 via methyldiethanolamine (MDEA) scrubbing from the blast furnace gas (BFG) are used to produce synthetic natural gas in an isothermal fixed bed methanation plant. The latter gas is injected into the blast furnace, closing a carbon loop and reducing coal consumption. The oxygen by-produced in the electrolyser covers the entire oxygen demand of the steelmaking plant and avoids the need for an air separation unit (ASU). The novelty of this work relies on the variation of the oxygen enrichment and its temperature in the hot blast, and how it influences the power to gas integration concept. This power to gas integration is compared with a conventional BF-BOF plant from a technical, economic, energy and environmental point of view. Both plant process configurations were implemented in Aspen Plus simulations, assessing the fossil fuel demand, energy penalty, cost and CO2 emissions. Emission reduction up to 34% can be achieved with power to gas integration, with an energy penalty of 17 MJ/tHM and a cost of 352 €/tCO2.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Technical and economic assessment of iron and steelmaking decarbonization via power to gas and amine scrubbing

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begoña
  • Romeo, Luis M.
  • Eveloy, Valerie
The iron and steel industry is one of the most energy-intensive industries, emitting 5% of the total anthropogenic carbon dioxide (CO2). The control of CO2 emissions has become increasingly stringent in the European Union (EU), resulting in EU allowance above 90 €/tCO2. Carbon capture will be required to achieve CO2 emissions control, and carbon utilization via power-to-gas could significantly increase interest in carbon capture in the iron and steel sector. This paper presents a new concept that combines amine scrubbing with power-to-gas to reduce emissions in blast furnace-basic oxygen furnace steelmaking plants. Synthetic natural gas (SNG) is produced using green hydrogen from water electrolysis and CO2 from steelmaking. The synthetic natural gas is later used as a reducing agent in the blast furnace, constantly recycling carbon in a closed loop and avoiding geological storage. The oxygen by-produced via electrolysis eliminates the necessity of an air separation unit. By applying these innovations to steelmaking, a reduction in CO2 emissions of 9.4% is obtained with an energy penalty of 16.2 MJ/kgCO2, and economic costs of 52 €/tHM or 283 €/tCO2. A sensitivity analysis with respect to electricity and the CO2 allowances prices is also performed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Full oxygen blast furnace steelmaking: From direct hydrogen injection to methanized BFG injection

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begoña
This paper presents a novel concept of Power to Gas in an oxygen blast furnace, through blast furnace gas methanation and direct H2 injection. The PEM electrolyser produces H2, which reacts with the CO and CO2 from the blast furnace gas forming synthetic natural gas. The latter gas is injected into the blast furnace, closing a carbon loop and avoiding CO2 emissions. A parametric analysis is performed to vary the H2:CO2 ratio in the methanation reaction. Different ratios are simulated and compared, among of which the most representative are: (i) 2.5, where unreacted CO2 is directly recycled with the synthetic natural gas; (ii) 4, where stoichiometric conditions are found and the synthetic gas is composed mostly by CH4; and (iii) 8, where an excess of H2 is found in the synthetic gas; and (iv) an infinite ratio, where only H2 is injected in the blast furnace. In the latter, the methanation plant is not required, and no synthetic natural gas is produced. The results show that low H2:CO2 ratios perform poorly, involving high PEM sizes and high costs but only a 5% of CO2 avoidance (compared to conventional blast furnaces). A H2:CO2 ratio of 4 and full H2 injection results in higher reduction of CO2 emissions (33.8 % and 28.6%) with carbon abatement costs of 260 and 245 €/tCO2, respectively.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Power to gas and top gas recycling integration in an oxygen blast furnace steelmaking industry

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begoña
  • Kannan, Pravin
  • Eveloy, Valerie
  • Romeo, Luis M.
A new process concept integrating power to methane with top gas recycling in an oxygen blast furnace (BF) is investigated to reduce the emission intensity of steelmaking. Power to gas produces synthetic methane using hydrogen (H2) generated by an electrolyser operated with renewable electricity, and CO2 captured from the BF gas by amine scrubbing supplied with heat from the methanation process. The clean gas from the amine scrubbing is recycled and injected in the BF (via top gas recycling), together with synthetic methane. A parametric analysis is performed to vary the amount of top gas recycled (from 0 kg/tHM to 270 kg/tHM). Based on the results, CO2 equivalent emissions can decrease by 34% using power to gas technology, and by 30% with power to gas and top gas recycling (compared to conventional BFs). Nevertheless, if both integrations are present, additional benefits on the specific energy consumption (12.0 MJ/tHM), and specific cost (130 €/tHM) are achieved, compared to only applying power to gas (17.5 MJ/tHM and 233 €/tHM). In all cases, the downstream thermal energy needs of the steel plant are fulfilled, contrarily to conventional top gas recycling concepts. The main conclusion is that top gas recycling should be considered together with PtG technology, and vice versa, when integrated in blast furnace ironmaking, in order to both abate emissions while supplying downstream energy needs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Integration of power to gas and biomass charcoal in oxygen blast furnace ironmaking

  • Bailera, Manuel
  • Rebolledo, Boris
The paper introduces a novel approach for mitigating CO2 emissions in blast furnaces by integrating top gas recycling, an oxy-fuel regime, power to gas, and biomass pyrolysis. Various case studies were conducted, involving the adjustment of pyrolysis temperatures (300 °C, 500 °C, 700 °C, and 900 °C) and varying the quantity of blast furnace gas directed to methanation for carbon recycling. Pinus radiata, abundant and cost-effective in Chile and Spain, was chosen as the biomass source. The integration was modeled using the extended operating line methodology and evaluated through 12 key performance indicators, such as flame temperature, coke consumption, CO2 emissions, and specific primary energy consumption per unit of CO2 avoided. Optimal performance was observed with pyrolysis at 700 °C and no blast furnace gas recycled through methanation. This configuration achieved a 58 % reduction in CO2 emissions, with an energy consumption of 9.8 MJ/kgCO2, and obviated the need for geological storage. Comparing this innovative proposal with other oxygen blast furnace approaches from the literature revealed a 13 percentage point improvement in CO2 reduction over the second-best alternative. Additionally, the required electrolysis capacity, influencing capital expenditure, was 57 % lower, and energy consumption was reduced by 44 %.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Outline of all potential Power to Gas integrations in blast furnace ironmaking: A systematic review

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begoña
This work presents the first systematic review analysis of potential Power to Gas integrations in blast furnace ironmaking. The primary objective of the paper is to evaluate the PtG technology implementation in both conventional air-blown and full oxygen blast furnaces, considering different BFG recycling routes (upper, shaft or tuyeres), and synthetic gases (SNG, H2 or syngas). Employing a systematic methodology, the paper compares all the studies using 14 Key Performance Indicators (KPI) and elaborates a discussion on the main findings and limitations, proposing areas for future research. PtG application enables air-blown blast furnaces to cut emissions to 1060 kgCO2/tHM. With PtG and top gas recycling, oxygen blast furnaces achieve a reduction to 747 kgCO2/tHM, and when combined with geological storage, the reduction further drops to 435 kgCO2/tHM. Additionally, the authors propose a novel PtG-ironmaking integration based on the findings of this paper.