Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microelectronic cmos implementation of a machine learning technique for sensor calibration

  • Martinez-Nieto, J.A.
  • Sanz-Pascual, M.T.
  • Medrano, N.
  • Calvo Lopez, B.
  • Antolín Cañada, D.
An integrated machine-learning based adaptive circuit for sensor calibration implemented in standard 0.18μm CMOS technology with 1.8V power supply is presented in this paper. In addition to linearizing the device response, the proposed system is also capable to correct offset and gain errors. The building blocks conforming the adaptive system are designed and experimentally characterized to generate numerical high-level models which are used to verify the proper performance of each analog block within a defined multilayer perceptron architecture. The network weights, obtained from the learning phase, are stored in a microcontroller EEPROM memory, and then loaded into each of the registers of the proposed integrated prototype. In order to verify the proposed system performance, the non-linear characteristic of a thermistor is compensated as an application example, achieving a relative error er below 3% within an input span of 130°C, which is almost 6 times less than the uncorrected response. The power consumption of the whole system is 1.4mW and it has an active area of 0.86mm 2 . The digital programmability of the network weights provides flexibility when a sensor change is required.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

1.0 v-0.18 µm CMOS tunable low pass filters with 73 db dr for on-chip sensing acquisition systems

  • Pérez-Bailón, Jorge
  • Calvo, Belén
  • Medrano, Nicolás
This paper presents a new approach based on the use of a Current Steering (CS) technique for the design of fully integrated Gm–C Low Pass Filters (LPF) with sub-Hz to kHz tunable cut-off frequencies and an enhanced power-area-dynamic range trade-off. The proposed approach has been experimentally validated by two different first-order single-ended LPFs designed in a 0.18 µm CMOS technology powered by a 1.0 V single supply: a folded-OTA based LPF and a mirrored-OTA based LPF. The first one exhibits a constant power consumption of 180 nW at 100 nA bias current with an active area of 0.00135 mm2 and a tunable cutoff frequency that spans over 4 orders of magnitude (~100 mHz–152 Hz @ CL = 50 pF) preserving dynamic figures greater than 78 dB. The second one exhibits a power consumption of 1.75 µW at 500 nA with an active area of 0.0137 mm2 and a tunable cutoff frequency that spans over 5 orders of magnitude (~80 mHz–~1.2 kHz @ CL = 50 pF) preserving a dynamic range greater than 73 dB. Compared with previously reported filters, this proposal is a competitive solution while satisfying the low-voltage low-power on-chip constraints, becoming a preferable choice for general-purpose reconfigurable front-end sensor interfaces.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A wireless instrumentation control system based on low-cost single board computer gateways

  • Enériz Orta, D.
  • Medrano, N.
  • Calvo, B.
Nowadays, most of the automatized measurement processes are carried out by VISA (Virtual Instrument Software Architecture) compatible instruments, that execute the instructions provided by a host computer connected through wired standard buses, as USB (Universal Serial Bus), GPIB (General-Purpose Instrumentation Bus), PXI (PCI eXtensions for Instrumentation) or Ethernet. To overcome the intrinsic limitations associated to these wired systems, this work presents an instrumentation control system based on the IEEE 802.11 wireless communications standard. Intended for instruments having a USB control port, this port is connected to a gateway based on a compact Raspberry Single Board Computer (SBC) and thus the instrument can be connected to the host computer via Wireless Fidelity (WiFi), easily allowing the deployment of an ad-hoc instruments communication network in the working area or its connection to a previously deployed general purpose WiFi network. Developed under Python, the operation commands, wireless link protocol, and USB connection allow two modes of operation to provide system flexibility: a live mode, where commands are sent individually from the host computer to the selected instrument; and a standalone mode, where a full measurement process can be entirely downloaded in the gateway to be autonomously executed on the instrumentation. The system performance in both operation modes, distance of operation, time latencies, and operating lifetime in battery operation have been characterized.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A fully-integrated 180 nm CMOS 1.2 V low-dropout regulator for low-power portable applications

  • Pérez-Bailón, J.
  • Calvo, B.
  • Medrano, N.
This paper presents the design and postlayout simulation results of a capacitor-less low dropout (LDO) regulator fully integrated in a low-cost standard 180 nm Complementary Metal-Oxide-Semiconductor (CMOS) technology which regulates the output voltage at 1.2 V from a 3.3 to 1.3 V battery over a -40 to 120 degrees C temperature range. To meet with the constraints of system-on-chip (SoC) battery-operated devices, ultralow power (I-q = 8.6 mu A) and minimum area consumption (0.109 mm(2)) are maintained, including a reference voltage V-ref = 0.4 V. It uses a high-gain dynamically biased folded-based error amplifier topology optimized for low-voltage operation that achieves an enhanced regulation-fast transient performance trade-off.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Wide-band compact 1.8 V-0.18 µm CMOS analog front-end for impedance spectroscopy

  • Perez-Bailon, J.
  • Sanz-Pascual, M. T.
  • Calvo, B.
  • Medrano, N.
In this letter, a fully integrated configurable front-end for Impedance Spectroscopy (IS) is presented. The circuit includes fully differential in-phase and quadrature channels, using a transconductor (TC)-transimpedance (TI) approach. The input TC, shared for both channels, is based on a programmable degenerated differential pair to attain low-noise programmable-gain, while identical TII/Q with embedded synchronous rectification provide both I, Q outputs, filtered through fc adjustable Gm-C integrators. It exhibits a programmable gain ranging from 0 dB to 40 dB with 87 MHz bandwidth, amplitude and phase recovery errors below 1.9% and 2.5∘ respectively and an input referred noise floor of 16.7 nV/Hz. The result is a high-performance very compact topology with a total power consumption of 292 μW at a 1.8 V power supply, thus constituting an appropriate solution for full on chip multichannel IS systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Three-Stage CMOS LDO with Optimized Power and Dynamic Performance for Portable Devices

  • Serrano-Reyes, Andrés
  • Sanz-Pascual, María Teresa
  • Calvo-López, Belén
Low dropout (LDO) regulators are crucial components in power management systems for portable, i.e., battery-powered, devices. However, the design of LDO regulators presents a challenging trade-off between dynamic performance, power consumption, and area efficiency. This paper proposes a novel LDO regulator design that addresses these challenges by employing the reverse nested Miller compensation (RNMC) with current buffers embedded within the own class AB high gain error amplifier (EA) topology, and a time response enhancement circuit (TREC). High-gain (>120 dB) class AB EA renders good regulation performance with enhanced dynamic performance. The proposed compensation scheme improves the gain bandwidth product (GBW) and stability of the regulator, while the TREC reduces overshoot and undershoot during load transients without additional steady-state power consumption. Post-layout simulations confirm the robustness of the proposed 180 nm CMOS design across a wide range of operating conditions, achieving a regulated output voltage of 1.8 V with 100 mV dropout, good load and line regulating performance, and excellent load transient response with reduced undershoot and overshoot at minimum power (Iq = 13.8 μA) and area (314 μm × 150 μm) consumption. The proposed LDO regulator thus offers a compelling compromise between power consumption, area efficiency, and dynamic performance, making it highly suitable for portable applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Outline of all potential Power to Gas integrations in blast furnace ironmaking: A systematic review

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begoña
This work presents the first systematic review analysis of potential Power to Gas integrations in blast furnace ironmaking. The primary objective of the paper is to evaluate the PtG technology implementation in both conventional air-blown and full oxygen blast furnaces, considering different BFG recycling routes (upper, shaft or tuyeres), and synthetic gases (SNG, H2 or syngas). Employing a systematic methodology, the paper compares all the studies using 14 Key Performance Indicators (KPI) and elaborates a discussion on the main findings and limitations, proposing areas for future research. PtG application enables air-blown blast furnaces to cut emissions to 1060 kgCO2/tHM. With PtG and top gas recycling, oxygen blast furnaces achieve a reduction to 747 kgCO2/tHM, and when combined with geological storage, the reduction further drops to 435 kgCO2/tHM. Additionally, the authors propose a novel PtG-ironmaking integration based on the findings of this paper.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Analysis of Varroa Mite Colony Infestation Level Using New Open Software Based on Deep Learning Techniques

  • Divasón, Jose
  • Romero, Ana
  • Martinez-de-Pison, Francisco Javier
  • Casalongue, Matías
  • Silvestre, Miguel A.
  • Santolaria, Pilar
  • Yániz, Jesús L.
Varroa mites, scientifically identified as Varroa destructor, pose a significant threat to beekeeping and cause one of the most destructive diseases affecting honey bee populations. These parasites attach to bees, feeding on their fat tissue, weakening their immune systems, reducing their lifespans, and even causing colony collapse. They also feed during the pre-imaginal stages of the honey bee in brood cells. Given the critical role of honey bees in pollination and the global food supply, controlling Varroa mites is imperative. One of the most common methods used to evaluate the level of Varroa mite infestation in a bee colony is to count all the mites that fall onto sticky boards placed at the bottom of a colony. However, this is usually a manual process that takes a considerable amount of time. This work proposes a deep learning approach for locating and counting Varroa mites using images of the sticky boards taken by smartphone cameras. To this end, a new realistic dataset has been built: it includes images containing numerous artifacts and blurred parts, which makes the task challenging. After testing various architectures (mainly based on two-stage detectors with feature pyramid networks), combination of hyperparameters and some image enhancement techniques, we have obtained a system that achieves a mean average precision (mAP) metric of 0.9073 on the validation set.