Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exotic grain growth law in twinned boron carbide under electric fields

  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Domínguez Rodríguez, Arturo
Grain growth is a ubiquitous phenomenon in all materials, and it affects both structural and functional properties. Despite its intrinsic importance, a full comprehension of grain growth from a fundamental point of view—i.e., from the nanoscale to the macroscale—is still a pending issue. In practical terms, our knowledge relies on the classical kinetic laws reported sixty years ago. This paper reports the violation of such classical laws in boron carbide ceramics consolidated by spark plasma sintering. The conjunction of high temperature gradients with large compressive stress when a pulse electric current passes through the ceramic powders gives rise to an intense twinning–detwinning formation. These forming steps at the grain boundaries change the grain mobility drastically. Therefore, a new ‘exotic’ law for grain-growth kinetics is found and validated at different temperatures and dwell times., The authors gratefully acknowledge the financial support provided by MINECO and FEDER Funds through the research project MAT2015-71411-R. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Grain-boundary diffusion coefficient in α-Al2O3 from spark plasma sintering tests: Evidence of collective motion of charge disconnections

  • Tamura, Yoshihiro
  • Zapata-Solvas, E.
  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Domínguez Rodríguez, Arturo
The sintering of fine-grained α-alumina by spark plasma sintering (SPS) was performed to study grain growth under SPS conditions. Grain growth is found to be extensive at relative densities above 95%. A grain growth versus dwell time analysis during SPS allows for the determination of the grain-boundary diffusion coefficient. This study shows that the remarkable enhancement of grain-boundary diffusion derived from a previous analysis could be a consequence of the presence of the recently discovered “disconnections” at the grain boundaries of α-alumina. Their presence, together with their electric charge and the external electric field at the boundaries, are the key ingredients for a violation of the typical grain growth kinetic law. When they are introduced appropriately, an updated value of the grain-boundary diffusion coefficient is achieved. A comparison with other values reported previously in the literature through other techniques and a critical analysis are also carried out., The authors acknowledge Nippon Steel & Sumitomo Metal Corporation, Japan for the doctoral thesis financial support awarded to Y. Tamura. They also acknowledge the financial support provided by the project from the Spanish ministry of Economy (MINECO) MAT-2015-71411-R as well as through a contract for Dr. Zapata-Solvas from the JAE-DOC program of CSIC, Spain. Dr. B. M. Moshtaghioun wants to acknowledge the financial support provided by the Spanish MINECO through the "Juan de la Cierva-Incorporación" contract during her postdoctoral stay in CSIC-Universidad de Zaragoza, Spain. The authors also acknowledge some financial support from the regional government "Junta de Andalucía" P12-FQM-1079., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Graphene or carbon nanofiber-reinforced zirconia composites: Are they really worthwhile for structural applications?

  • Cano-Crespo, Rafael
  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Moreno, Rodrigo
  • Domínguez Rodríguez, Arturo
The use of allotropic phases of carbon (i.e. nanotubes, graphene or carbon nanofibers) as second phases to design ceramic composites is a hot topic at present. Researchers try to provide a remarkable improvement of the parent ceramic assuming that some of the outstanding mechanical properties of these phases migrate to the resultant composite. This reasonable idea has been questioned severely in the case of nanotubes addition but there is not any analysis for the other two phases cited previously. To elucidate this question, zirconia was selected as a model ceramic. This paper reports the mechanical properties of zirconia composites reinforced either with graphene or carbon nanofibers, with special emphasis on the high-temperature plasticity., The authors acknowledge the financial support awarded by the Regional project of Excellence of “Junta de Andalucía”P12-FQM-1079 and the Spanish MINECO and FEDER funds through the projects MAT2015-71411-R and MAT2015-67586-C3-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spark plasma sintering of fine-grained alumina ceramics reinforced with alumina whiskers

  • Tamura, Yoshihiro
  • Malmal Moshtaghioun, Bibi
  • Gómez-García, Diego
  • Domínguez Rodríguez, Arturo
Densification of alumina whisker-reinforced alumina ceramics by spark plasma sintering (SPS) has been investigated with the aim of obtaining a fine-grained microstructure and also studying the effect of whisker addition on the room-temperature mechanical properties. It was found that whisker addition retards slightly the sinterability of alumina by whisker hindering of particle rearrangement. Besides, the internal stress on the alumina matrix particles reduced due to the presence of a whisker network structure of strong rigid boundaries. Nevertheless near fully-dense and fine-grained alumina ceramics with alumina whisker content between 3 wt% and 10 wt% could be obtained under appropriate SPS conditions. The hardness of alumina ceramics with 3 wt% was comparable to that of pure alumina ceramics (∼26 GPa) whereas its fracture toughness (5.6 MPa m) was higher (4.2 MPa m). Crack bridging by well-dispersed whiskers and whiskers pull-out were identified as the main toughening mechanisms., The authors acknowledge Nippon Steel & Sumitomo Metal Corporation (Japan) for doctoral thesis financial support through a Spanish-Japanese research joint project (FIUS1967/0679), the project from Spanish Ministry of Science MAT-2015–71411-R and the project from Andalucia Government P12-FQM-1079.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Carbon nanofibers replacing graphene oxide in ceramic composites as a reinforcing-phase: Is it feasible?

  • Cano-Crespo, Rafael
  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
  • Moreno, Rodrigo
In recent years, the interest of graphene and graphene-oxide has increased extraordinarily due to the outstanding properties concurring in this material. In ceramic science, the possibility of combining excellent electrical conductivities together with an enhancement of mechanical properties has motivated the research in fabrication of graphene oxide-reinforced ceramic composites despite the intrinsic difficulties for sintering. In this work a comparison is made between graphene oxide-reinforced alumina composites and carbon nanofiber-reinforced alumina ones. It will be concluded that the improvement of mechanical properties is scarce, if any. Since carbon nanofibers have also a good electrical conductivity their importance for future applications as a replacement of more sophisticated but expensive graphene-based ceramic composites will be stressed., The authors acknowledge the financial support awarded by the Regional project of Excellence of “Junta de Andalucía”P12-FQM-1079 and the Spanish MINECO and FEDER funds through the projects MAT2015-71411-R and MAT2015-67586-C3-2-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ceramics of Ta-doping stabilized orthorhombic ZrO2 densified by spark plasma sintering and the effect of post-annealing in air

  • Sponchia, Gabriele
  • Moshtaghioun, Bibi Malmal
  • Benedetti, Alvise
  • Riello, Prieto
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
  • Ortiz, Ángel L.
16 mol% Ta-doped ZrO powders were synthesized and densified by spark-plasma sintering (SPS) in vacuum, followed by post-SPS annealing in air, thus obtaining two ultrafine-grained ceramics consisting of Ta-doping stabilized orthorhombic ZrO. The as-SPSed ceramic is black because it is actually a suboxide essentially with reduced cations and abundant oxygen vacancies, whereas the post-annealed ceramic is white because it is an oxide without vacancies and with only partially reduced cations. Both ceramics are relatively hard and brittle, but the as-SPSed ceramic was slightly more so, attributable to crystallographic and microstructural differences. Implications of interest for the ceramics community are discussed., This work was supported by the Junta de Andalucía under Grant n° P12-FQM-1079 and from the Junta de Extremadura under Grant n° GR15078, co-financed with FEDER Funds. Financial support from the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under the Grants n° MAT2013–41012-P and MAT2015-71411-R is gratefully acknowledged as well.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Does grain size have an influence on intrinsic mechanical properties and conduction mechanism of near fully-dense boron carbide ceramics?

  • Moshtaghioun, Bibi Malmal
  • Laguna-Bercero, M. A.
  • Gómez-García, Diego
  • Peña, J. I.
This work is concentrated on getting a reply to the following question: how does the grain size of boron carbide specimens influence on their mechanical and electrical response? It is a common issue that both essential properties are usually affected by the grain boundaries. To this purpose, a set of near fully-dense boron carbide specimens were prepared by spark plasma sintering. In order to reduce residual porosity and grain-size effects, nanoindentation tests at room temperature were conducted. DC conductivity was measured through four-point test technique from room temperature up to 800 °C. The results show that hardness can reach values as high as ∼60 GPa and plasticity onset takes place at around 23 GPa by dislocation nucleation. Regarding the conductivity, it is found that grain boundaries can block the mobility of bipolarons in an effective way. A simple additive law is provided to account for the resistivity of boron carbide polycrystals., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2015- 71411-R. and MAT2016-77769-R wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Elusive super-hard B6C accessible through the laser-foating zone method

  • Moshtaghioun, Bibi Malmal
  • Cumbrera, F. L.
  • Gómez-García, Diego
  • Peña, J. I.
Boron carbide is among the most promising ceramic materials nowadays: their mechanical properties are outstanding, and they open potential critical applications in near future. Since sinterability is the most critical drawback to this goal, innovative and competitive sintering procedures are attractive research topics in the science and technology of this carbide. This work reports the pioneer use of the laser-floating zone technique with this carbide. Crystallographic, microstructural and mechanical characterization of the so-prepared samples is carefully analysed. One unexpected output is the fabrication of a B6C composite when critical conditions of growth rate are adopted. Since this is one of the hardest materials in Nature and it is achievable only under extremely high pressures and temperatures in hot-pressing, the use of this technique offers a promising alternative for the fabrication. Hardness and elastic modulus of this material reached to 52 GPa and 600 GPa respectively, which is close to theoretical predictions reported in literature., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants Nos MAT2015-71411-R and MAT2016-77769-R. B.M.M. wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-temperature compressive creep of novel fine-grained orthorhombic ZrO2 ceramics stabilized with 12 mol% Ta doping

  • Sponchia, Gabriele
  • Moshtaghioun, Bibi Malmal
  • Riello, Prieto
  • Benedetti, Alvise
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Domingo
  • Ortiz, Ángel L.
A novel fine-grained orthorhombic ZrO2 ceramic stabilized with 12 mol% Ta doping was fabricated by spark-plasma sintering from home-made powders, and its high-temperature mechanical properties evaluated for the first time by compressive creep tests in both Ar and air. It was found that the high-temperature plasticity of the ceramic deformed in Ar, under which the Ta-doped orthorhombic ZrO2 is a black suboxide with abundant oxygen vacancies in its crystal structure, is controlled by grain boundary sliding (stress exponent ∼2, and activation energy ∼780–800 kJ/mol). However, the high-temperature plasticity of the ceramic deformed in air, under which the Ta-doped orthorhombic ZrO2 is a white oxide due to the elimination in situ of oxygen vacancies, is controlled by recovery creep (stress exponent ∼3, and activation energy ∼750 kJ/mol). It was also observed that black Ta-doped orthorhombic ZrO2 is more creep resistant than its white counterpart with the same grain size, and that the former deforms as the more conventional Y2O3-stabilized ZrO2 does., This work was supported by the Junta de Andalucía under Grant nº P12-FQM-1079 and by the Junta de Extremadura under Grant nº GR15078, co-financed with FEDER Funds. Financial support from the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants nº MAT2015-71411-R and MAT2016-76638-R is gratefully acknowledged as well.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High temperature creep of 20 vol%. SiC-HfB2 UHTCs up to 2000 °C and the effect of La2O3 addition

  • Zapata-Solvas, E.
  • Gómez-García, Diego
  • Domínguez-Rodríguez, A.
  • Lee, W. E.
High temperature compressive creep of SiC-HfB2 UHTCs up to 2000 °C has been studied. Microstructural analysis after deformation reveals formation of new phases in the Hf-B-Si and Hf-B-Si-C systems, which are responsible for the poor creep resistance. RE oxide additions have a negative effect reducing the creep resistance of SiC-HfB2 UHTCs. A simplistic analysis for the required creep resistance is described, indicating that only SiC-HfB2 UHTCs could withstand re-entry conditions for 5 min in a single use. However, RE oxide addition to SiC-HfB2 UHTCs does not provide the required creep resistance for them to be candidate materials for hypersonic applications., EZS also acknowledges support through a contract from the JAE-DOC program of CSIC, Spain, co-funded by the FSE to carry out this research project (2012–2015). DGG, ADR and EZS acknowledge the project MAT2015-71411-R from MINECO (Spain). EZS and WEL acknowledges the EPSRC grant XMAT (EP/K008749/1) for supporting this research and EZS while doing compression testing at Imperial College London., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Is an alumina-whisker-reinforced alumina composite the most efficient choice for an oxidation-resistant high-temperature ceramic?

  • Tamura, Yoshihiro
  • Moshtaghioun, Bibi Malmal
  • Zapata-Solvas, E.
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
  • Cerecedo-Fernández, Carmen
  • Valcárcel-Juárez, Víctor
The search of a competitive ceramic material for structural applications demands several requisites: a simple microstructure with easy reproducibility, good intrinsic mechanical properties and most of all, an optimal oxidation resistance. This later point is a challenging point for most ultrahigh refractory materials. In this work an alumina (AlO) whisker-reinforced AlO composite prepared by spark plasma sintering (SPS) is studied. It will be shown that, although the microstructure is quite similar to that of pure monolithic one, there is a notorious enhancement of the high-temperature deformation resistance, reaching up to one order of magnitude over the pure AlO specimen. On the other hand, the activation energy of these composites increases notably. The results are explained in terms of an original model. A comparison with reported data shows that such composite is as efficient as a SiC-whisker-reinforced AlO composite, with the advantage of its oxidation resistance and much less fabrication cost., The authors acknowledge Nippon Steel & Sumitomo Metal Corporation (Japan) for doctoral thesis financial support through a Spanish-Japanese research joint project (FIUS1967/0679), the project from Spanish Ministry of Science MAT-2015–71411-R and the project from Andalucía Government P12-FQM-1079. EZS also acknowledges support through a contract from the JAE-DOC program of CSIC, Spain, co-funded by the FSE (2012–2015). This work is also supported by Guangdong Innovative and Entrepreneurial Research Team Program (No. 2013C099) and International Science & Technology Cooperation Program of China (No. 2014DFA2014DFA53020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spark plasma sintering of titanium nitride in nitrogen: Does it affect the sinterability and the mechanical properties?

  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
Titanium nitride ceramics have an intrinsic interest due to its optical and structural applications. However, the conditions for sintering of dense pieces are not still clarified. This research work is focused on the spark plasma sintering (SPS) of near-fully dense fine-grained TiN. The main goal is giving a response to a longstanding debate: can the external atmosphere favor sintering? Different sintering atmospheres, either vacuum or a nitrogen flow, have been used during SPS heating to this purpose. X ray diffraction analysis has showed the presence of TiN as the main phase with traces of Ti4O7 in optimal SPS conditions (1600 °C, one minute dwell time). Our results show that the use of a nitrogen flow while heating can improve sinterability very slightly, but mechanical properties are essentially unaltered within the experimental uncertainty. The hardness reaches values as high as 20GPa whereas fracture toughness can be evaluated around 4 MPam1/2., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER funds under the Research project MAT2015-71411-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sintering kinetics, defect chemistry and room-temperature mechanical properties of titanium nitride prepared by spark plasma sintering

  • Morgado Chávez, Jose M.
  • Moshtaghioun, Bibi Malmal
  • Cumbrera, Francisco Luis
  • Gómez-García, Diego
Fully dense titanium nitride polycrystals have been prepared by spark plasma sintering. The kinetics of the sintering process and the optimized conditions for SPS processing have been put forward. Microstructural analyses of the resulting samples have unambiguously shown the coexistence of titanium as Ti, Ti and Ti, thus driving the presence of cation vacancies. This fact is a new ingredient which is shown to influence the mechanical properties of this strategic ceramic., The authors want to acknowledge the financial support provided by the research project MAT2015-71411-R awarded by the Spanish authorities. JMM wants to acknowledge the support provided by the Regional Government ‘Junta de Andalucía' through his contract in frame of the ‘Plan de Empleo Joven’ program. BMM expresses her recognition to the Spanish Ministry of Science for her postdoctoral contract through the ‘Juan de la Cierva-incorporación' program at the University of Zaragoza, Spain.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Disclination dipoles are the Holy Grail for high temperature superplasticity in ceramics

  • Moshtaghioun, Bibi Malmal
  • Bejarano-Palma, José Antonio
  • Gómez-García, Diego
A model for high-temperature plasticity of polycrystals controlled by disclination dipoles is proposed that predict a parabolic dependence of the strain rate versus the applied stress. The presence of a precise stationary disclination density explains the origin of plasticity without microstructural invariance, commonly known as superplasticity. The disclination mechanism is universal, although other processes, such as dislocation glide, are superposed to this one in many systems such as metals or metallic alloys. While, in ceramics it is likely to be the only operative mechanism. Activation of disclination dipoles is a necessary condition for plasticity and sufficient one for superplastic yielding., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2015-71411-R. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza and also the funding by the ‘Junta de Andalucía’ Regional Government through the project P18-RTJ-1972., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mg2SiO4-MgAl2O4 directionally solidified eutectics: Hardness dependence modelled through an array of screw dislocations

  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Peña, J. I.
Mg2SiO4-MgAl2O4 eutectic ceramics have been fabricated by means of the laser floating zone (LFZ) technique. The microstructure has revealed as an unusual one at lower growth rate, composed of broken lamellae of MgAl2O4 distributed randomly along one matrix, composed of Mg2SiO4. At higher growth rates, a cell structure with intra-cell lamella structure is dominant. Contrary to most eutectic systems, hardness is not dependent upon the inter-spacing, but it does depend on one characteristic length of lamellae: their perimeter. One simple model based upon the dislocation is proposed, which successfully accounts for such extraordinary hardness law. Accordingly, Mg2SiO4-MgAl2O4 eutectic ceramics fabricated at 50 mm/h growth rate with the smallest MgAl2O4 lamella perimeter favorably showed more elevated hardness (13.4 GPa from Vickers indentation and 15.3 GPa from nanoindentation) and strength (∼430 MPa) than those found in the monolithic Mg2SiO4 matrix., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2016-77769-R and MAT2015- 71411-R and Gobierno de Aragon (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza and the ‘Junta de Andalucía’ project P18-RTJ-1972., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cation-driven electrical conductivity in Ta-doped orthorhombic zirconia ceramics

  • Moshtaghioun, Bibi Malmal
  • Laguna-Bercero, M. A.
  • Peña, J. I.
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
This paper is devoted to the study of the electrical conductivity of tantalum-doped zirconia ceramics prepared by spark plasma sintering. In this study, the temperature dependence of conductivity in as-prepared specimens and in those previously annealed in air is determined and compared. A semi-empirical model, which is based on the oxidation states of the cations, has been developed and successfully assessed. According to this, the conductivity is basically controlled by the diffusion of tetravalent zirconium cations in both cases, although the concentration of these species varies drastically with the amount of induced oxygen vacancies. This is a quite unexpected fact, since conductivity is normally controlled by anionic diffusion in zirconia ceramics. This option is forbidden here due to the presence of substitutional pentavalent cations. Therefore, conductivity values are much lower than those reported in trivalent or divalent substitutional cation doped zirconia ceramics., The authors would like to acknowledge provided by several institutions: BMM wants to acknowledge the Spanish Ministry of Science and Innovation through the grant PID2019-103847RJ-I00, as well as the financial support awarded by the Regional government of the ‘Junta de Andalucía’ through the project P18-RTJ-1972. BMM and JIP gratefully acknowledge the financial support provided the Ministry of Science in Spain through the projects MAT2016-77769-R and Gobierno de Aragón, Spain (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. MLB acknowledges the funding support provided by the projects MAT2015-68078-R and PID2019-107106RB-C32 funded by the Spanish Ministry of Science and Innovation. Finally, DGG and ADR are grateful to the Spanish Ministry of Science for the research funding through the project MAT2015-71411-R., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Graphene or carbon nanofiber-reinforced zirconia composites: Are they really worthwhile for structural applications?

  • Cano-Crespo, R.
  • Moshtaghioun, B.M.
  • Gómez-García, D.
  • Moreno, R.
  • Domínguez-Rodríguez, A.
The use of allotropic phases of carbon (i.e. nanotubes, graphene or carbon nanofibers) as second phases to design ceramic composites is a hot topic at present. Researchers try to provide a remarkable improvement of the parent ceramic assuming that some of the outstanding mechanical properties of these phases migrate to the resultant composite. This reasonable idea has been questioned severely in the case of nanotubes addition but there is not any analysis for the other two phases cited previously. To elucidate this question, zirconia was selected as a model ceramic. This paper reports the mechanical properties of zirconia composites reinforced either with graphene or carbon nanofibers, with special emphasis on the high-temperature plasticity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Mg2SiO4-MgAl2O4 directionally solidified eutectics: Hardness dependence modelled through an array of screw dislocations

  • Moshtaghioun, B.M.
  • Gomez-Garcia, D.
  • Peña, J.I.
Mg2SiO4-MgAl2O4 eutectic ceramics have been fabricated by means of the laser floating zone (LFZ) technique. The microstructure has revealed as an unusual one at lower growth rate, composed of broken lamellae of MgAl2O4 distributed randomly along one matrix, composed of Mg2SiO4. At higher growth rates, a cell structure with intra-cell lamella structure is dominant. Contrary to most eutectic systems, hardness is not dependent upon the inter-spacing, but it does depend on one characteristic length of lamellae: their perimeter. One simple model based upon the dislocation is proposed, which successfully accounts for such extraordinary hardness law. Accordingly, Mg2SiO4-MgAl2O4 eutectic ceramics fabricated at 50 mm/h growth rate with the smallest MgAl2O4 lamella perimeter favorably showed more elevated hardness (13.4 GPa from Vickers indentation and 15.3 GPa from nanoindentation) and strength (~430 MPa) than those found in the monolithic Mg2SiO4 matrix.