Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Graphene or carbon nanofiber-reinforced zirconia composites: Are they really worthwhile for structural applications?

  • Cano-Crespo, Rafael
  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Moreno, Rodrigo
  • Domínguez Rodríguez, Arturo
The use of allotropic phases of carbon (i.e. nanotubes, graphene or carbon nanofibers) as second phases to design ceramic composites is a hot topic at present. Researchers try to provide a remarkable improvement of the parent ceramic assuming that some of the outstanding mechanical properties of these phases migrate to the resultant composite. This reasonable idea has been questioned severely in the case of nanotubes addition but there is not any analysis for the other two phases cited previously. To elucidate this question, zirconia was selected as a model ceramic. This paper reports the mechanical properties of zirconia composites reinforced either with graphene or carbon nanofibers, with special emphasis on the high-temperature plasticity., The authors acknowledge the financial support awarded by the Regional project of Excellence of “Junta de Andalucía”P12-FQM-1079 and the Spanish MINECO and FEDER funds through the projects MAT2015-71411-R and MAT2015-67586-C3-2-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Carbon nanofibers replacing graphene oxide in ceramic composites as a reinforcing-phase: Is it feasible?

  • Cano-Crespo, Rafael
  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
  • Moreno, Rodrigo
In recent years, the interest of graphene and graphene-oxide has increased extraordinarily due to the outstanding properties concurring in this material. In ceramic science, the possibility of combining excellent electrical conductivities together with an enhancement of mechanical properties has motivated the research in fabrication of graphene oxide-reinforced ceramic composites despite the intrinsic difficulties for sintering. In this work a comparison is made between graphene oxide-reinforced alumina composites and carbon nanofiber-reinforced alumina ones. It will be concluded that the improvement of mechanical properties is scarce, if any. Since carbon nanofibers have also a good electrical conductivity their importance for future applications as a replacement of more sophisticated but expensive graphene-based ceramic composites will be stressed., The authors acknowledge the financial support awarded by the Regional project of Excellence of “Junta de Andalucía”P12-FQM-1079 and the Spanish MINECO and FEDER funds through the projects MAT2015-71411-R and MAT2015-67586-C3-2-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Friction and wear behavior of alumina-based graphene and CNFs composites

  • Gutiérrez-Mora, F.
  • Cano-Crespo, R.
  • Rincón, A.
  • Moreno, Rodrigo
  • Domínguez-Rodríguez, A.
Alumina – carbon nanofibers (CNF) and alumina – graphene oxide (GO) composites were prepared by spark plasma sintering using freeze-dried powders prepared from optimized suspensions of the mixtures. The tribological behavior was studied using the ball-on-disk technique in dry sliding at ambient conditions and compared to a monolithic alumina used as a reference. At low loads there was little difference between friction and wear behavior, whereas at moderate loads the composites showed a noticeable reduction in wear rate over monolithic alumina, five and 2.5 times for the GO and the CNF composite respectively; the friction coefficient slightly decreased for the alumina – GO material. This behavior is related to the presence of a carbon-rich protecting tribofilm. The film present in the alumina – GO showed better tribological performance due to the absence of coalescence of cracks that led to delamination events in the case of the alumina – CNF composite., The authors acknowledge the financial support provided by the Junta de Andalucía (Spain) – Regional Proyect of Excellence P12-FQM-1079. It was also financied by Ministerio de Ciencia e Innovación (Government of Spain) and FEDER Funds under the Grant no. MAT 2015-67586-C3-2-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optimization of laser-patterned YSZ-LSM composite cathode-electrolyte interfaces for solid oxide fuel cells

  • Cebollero, Jose Antonio
  • Laguna-Bercero, M. A.
  • Lahoz, Fernando J.
  • Silva-Treviño, J.
  • Moreno, Rodrigo
  • Larrea, Ángel
Patterned cathode/electrolyte interfaces formed by a hexagonal array of ∼22 μm deep wells with 24 μm lattice parameter have been prepared by pulsed laser machining to enlarge the contact surface and, consequently, to reduce the cathode polarization of Solid Oxide Fuel Cells. These new interfaces have been tested in YSZ-LSM/YSZ/YSZ-LSM symmetrical cells, where the cathode is deposited by dip-coating. Appropriate ceramic suspensions have been formulated to penetrate into deep wells without presenting interfacial delamination after sintering. We analyse their applicability by comparing their rheology with the microstructure and electrochemical performance of the cells. The activation component of the polarization resistance is reduced by ∼50% using ethanol-based suspensions with 20 wt% solids loading, although the gas diffusion component increases due to excessive densification. Alternative ceramic suspensions with 17.5 wt% solids loading provide optimum electrode gas diffusion but lower activation components, resulting in an overall decrease of ∼20% in polarization resistance., This work was funded by the MAT2015-68078-R and MAT2015-67586-C3-2-R projects, which are financed by the Spanish Government (Ministerio de Economía y Competitividad) and the Feder Program of the European Union.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Better ceramics through colloid chemistry

  • Moreno, Rodrigo
[EN] In this work, the key role of colloid chemistry in the development of novel processing routes for ceramic manufacture is reported. An overview of the origins of a ceramic processing science is presented, emphasizing the pioneering works and the scientific fundaments of all processing steps that make use of suspensions. A brief review of the importance of colloid chemistry in the synthesis of nanoparticles with controlled purity, size and shape is given, followed by a description of the suspension properties and their effect in the beneficiation and shaping of ceramics. The main shaping techniques for the production of bulk parts, substrates and coatings and layered ceramics are shown, as well as the multiple possibilities for the design of composites with tailored microstructures and microarchitectures., This work has been supported by the Spanish Ministry of Economy, Industry and Competitiveness and FEDER Funds under Grants MAT2015-67586-C3-2-R (MINECO/FEDER, UE) and RTI2018-099033-B-C33 (MCIU/AEI/FEDER, UE). The author greatly acknowledges the JECS Trust Board members for the concession of the JECS Trust Award 2017.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Nd3+ Doping on the Structure, Thermal Evolution and Photoluminescence Properties of Nanoparticulate TiO2 Xerogels

  • Colomer, María T.
  • Roa, Carlos
  • Ortiz, Ángel L.
  • Ballesteros, Luz M.
  • Molina, Pablo
[EN] Undoped and Nd-doped xerogels (Nd-dopant content in the range 0.5–10 mol%) were obtained from colloidal sols in turn prepared by a “green sol-gel route” in aqueous media. The as-synthesized xerogels were characterized by X-ray diffractometry (XRD), high resolution electron microscopy (HREM) together with selected area electron diffractometry (SAED), and Raman spectroscopy (RS), finding that they crystallize as tiny nanocrystals of anatase with traces of brookite and rutile. The thermal stability of the as-synthesized xerogels was next studied in-situ by X-ray thermo-diffractometry (XRTD) as well as ex-situ by XRD, HREM/SAED, and RS on xerogels calcined at different temperatures (400–900 °C), concluding that Nd doping results in the formation of substitutional solid solutions with enlarged unit-cell volume that (i) stabilizes the anatase phase retarding the onset of its transformation to rutile to ever higher temperatures and (ii) provides the anatase nanocrystals with superior resistance to crystal growth. It was also found that NdTiO eventually precipitates at high temperatures when the Nd-dopant content is equal to or higher than 3 mol%, which leaves the still-existing anatase nanocrystals without stabilizer cations therefore causing their immediate transformation to rutile. Finally, the photoluminescence (PL) behaviour of the Nd-doped TiO xerogels with both anatase and rutile crystal structures was investigated and critically compared, observing that the PL emission (i) increases with increasing crystallinity of the host nanocrystals, (ii) decreases above a certain optimal Nd-dopant content due to concentration quenching, and (iii) is much greater for rutile host matrices. In this scenario, the 3 mol% Nd-doped rutile xerogel maximized the PL emission, emitting at both ∼915 and 925 nm due to the existence of two distinct local crystal fields for the Nd cations., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under the Grants nº MAT2016-76638-R, MAT2015-67586-C3-2-R, and MAT2016-78700-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Controlling colloidal processing of (K,Na)NbO3-based materials in aqueous medium

  • Venet, Michel
  • Santa-Rosa, Washington
  • M'Peko, Jean-Claude
  • Amorín, Harvey
  • Algueró, Miguel
  • Moreno, Rodrigo
[EN] K0:5Na0:5NbO3-based materials are serious candidates to replace leadbased piezoceramics since they show excellent electrical and piezoelectric properties. The tape casting technique can be used to obtain highly textured KNN-based ceramics; however, despite industrial and environmental advantages of water-based processing, there are not reports about the control of colloidal processing conditions to obtain optimized K0:5Na0:5NbO3-based slurries in aqueous medium. This paper reports a procedure for controlling colloidal stability and rheological behavior of aqueous (K0:5Na0:5)0:97Li0:03Nb0:8Ta0:2O3 suspensions. Zeta potential and cationic solubility measurements as a function of pH showed that pH 8.5 is adequate for concentrated suspensions, while ow curves analysis allowed optimizing processing parameters, such as, powder content, amount of de occulant and binder, and sonication time. Optimized colloidal suspensions were prepared and used to obtain high quality tapes. Processed ceramics from these stacked tapes show equivalent properties to those processed directly from powders, which demonstrates the effectiveness of the colloidal route reported here., Research co-funded by the Coordenacao de Aperfeicoamento de Pessoal de Nivel Superior - Brasil (CAPES) - Finance Code 001 (process 88881.030500/2013-01), Sao Paulo Research Foundation FAPESP (grants#2013/00134-7 and #2017/17872-1), and Spanish MINECO (projects MAT2014-58816-R, MAT2015-67586-CR-2-R, and MAT2017-88788-R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microwave-assisted synthesis of TiO2 nanoparticles: photocatalytic activity of powders and thin films

  • Falk, Gilberto S.
  • Borlaf, Mario
  • López-Muñoz, M. José
  • Fariñas, Juan C.
  • Rodrigues Neto, J. B.
  • Moreno, Rodrigo
A simple, rapid, and effective synthesis methodology for the preparation of high-performance TiO2 nanoparticles and thin films by combining colloidal sol-gel and microwave-assisted hydrothermal synthesis was developed. The obtained results indicate that the heating with microwaves at 180 °C for 20 min was enough to synthesize crystalline TiO2 nanoparticles, presenting anatase as a major phase with a crystal size of ~ 7 nm and a specific surface area of 220 m2 g−1. A secondary thermal treatment improved the crystallinity and induced the anatase-to-rutile transformation. The highest photocatalytic activity was found for the as-synthesized powder without any additional thermal treatment. Thin films were also prepared by dip-coating and its high photocatalytic activity showed a kinetic curve comparable to that of a thin film of commercial TiO2 powder prepared under similar conditions., This work was supported by Ministerio de Economía, Industria y Competitividad (Government of Spain) and FEDER Funds under the Grant No. MAT2015-67586-C3-2-R and CTM2015-69246-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microwave-assisted synthesis of Nb2O5 for photocatalytic application of nanopowders and thin films

  • Falk, Gilberto
  • Borlaf, Mario
  • López-Muñoz, María José
  • Fariñas, Juan C.
  • Rodrigues Neto, João Batista
  • Moreno, Rodrigo
A new rapid and energy saving method for the obtention of high performance nanoparticles and thin films of Nb2O5 by microwave-assisted hydrothermal synthesis is reported. The hydrothermal treatment of a sol-gel precursor solution in a microwave oven at 180 °C for 20 min was enough to obtain amorphous nanoparticles with average sizes of 40 nm. The calcination promotes the formation of different phases of Nb2O5 (TT and T) with pseudohexagonal and orthorhombic structure, respectively, that transform at higher temperatures in a mixture of orthorhombic and monoclinic phases. Crystalline phase composition was found to have a significant influence on the photocatalytic activity. The best photocatalytic performance was observed for the material mainly constituted by the TT-Nb2O5 phase. Thin films constituted by the TT phase were prepared by dip-coating. Photocatalytic experiments confirmed the high photocatalytic activity of this material, which showed a kinetic curve similar to that of a reference TiO2-P25 thin film., This work was supported by Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under the Grant no. MAT2015-67586-C3-2-R and CTM2015-69246-R. The authors thank the resources provided by CAPES under the International Cooperation Program Science without Borders for Special Guest Researcher, PVE (MEC/MCTI/CAPES/CNPQ/FAP/71/2013), Project No. A011/2013., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation of manganese oxide - graphite electrodes by electrophoretic deposition

  • Argüello, Juan A.
  • Cerpa, Arisbel
  • Alanbari, Mohammad H.
  • Fariñas, Juan C.
  • Moreno, Rodrigo
Manganese oxide is a promising active material for supercapacitors (SCs) with pseudocapacitance due to its high capacitance and its environmentally friendly character. This paper deals with the preparation of electrodes for supercapacitors consisting of manganese oxide supported onto graphite by electrophoretic deposition. Manganese oxide powders were characterized and dispersed in water by controlling the colloidal and rheological behavior in order to obtain stable suspensions. Optimized manganese oxide suspensions were deposited onto graphite electrodes by electrophoretic deposition. The deposited mass per unit area in the electrodes was optimized by controlling the applied current density and the deposition time. It has been demonstrated that the introduction of a binder helped to improve the adherence to graphite; otherwise the deposit thickness obtained by EPD is limited and no films can be obtained by simply dipping. These conditions allowed us to obtain more homogeneous deposits with higher specific energy than without binder., This work was supported by Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under the Grant no. MAT2015-67586-C3-R. Financial support from the UEM under the Grant no. 2016/UEM17 is gratefully acknowledged as well., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Graphene or carbon nanofiber-reinforced zirconia composites: Are they really worthwhile for structural applications?

  • Cano-Crespo, R.
  • Moshtaghioun, B.M.
  • Gómez-García, D.
  • Moreno, R.
  • Domínguez-Rodríguez, A.
The use of allotropic phases of carbon (i.e. nanotubes, graphene or carbon nanofibers) as second phases to design ceramic composites is a hot topic at present. Researchers try to provide a remarkable improvement of the parent ceramic assuming that some of the outstanding mechanical properties of these phases migrate to the resultant composite. This reasonable idea has been questioned severely in the case of nanotubes addition but there is not any analysis for the other two phases cited previously. To elucidate this question, zirconia was selected as a model ceramic. This paper reports the mechanical properties of zirconia composites reinforced either with graphene or carbon nanofibers, with special emphasis on the high-temperature plasticity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Optimization of laser-patterned YSZ-LSM composite cathode-electrolyte interfaces for solid oxide fuel cells

  • Cebollero, J.A.
  • Laguna-Bercero, M.A.
  • Lahoz, R.
  • Silva, J.
  • Moreno, R.
  • Larrea, A.
Patterned cathode/electrolyte interfaces formed by a hexagonal array of ~22 µm deep wells with 24 µm lattice parameter have been prepared by pulsed laser machining to enlarge the contact surface and, consequently, to reduce the cathode polarization of Solid Oxide Fuel Cells. These new interfaces have been tested in YSZ-LSM/YSZ/YSZ-LSM symmetrical cells, where the cathode is deposited by dip-coating. Appropriate ceramic suspensions have been formulated to penetrate into deep wells without presenting interfacial delamination after sintering. We analyse their applicability by comparing their rheology with the microstructure and electrochemical performance of the cells. The activation component of the polarization resistance is reduced by ~50% using ethanol-based suspensions with 20 wt% solids loading, although the gas diffusion component increases due to excessive densification. Alternative ceramic suspensions with 17.5 wt% solids loading provide optimum electrode gas diffusion but lower activation components, resulting in an overall decrease of ~20% in polarization resistance.