Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 36
Encontrada(s) 1 página(s)

Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Thermophysical properties of choline and pyridinium based ionic liquids as advanced materials for energy applications

  • Parajó Vieito, Juan José
  • Villanueva López, María
  • Troncoso Casares, Jacobo
  • Salgado Carballo, Josefa
Phase transitions, isobaric heat capacities and thermal stability of four ionic liquids (ILs) are determined in this work. The selected Ionic Liquids (ILs) have two different cations, pyridinium and choline, and they are combined with three different anions, acetate, dihydrogen phosphate and tosylate. Solid-solid and solid-liquid phase transitions and isobaric molar heat capacities are determined using two calorimeters, both based on the differential scanning calorimetry methodology. Thermal stability of the studied compounds is analysed through the thermogravimetric technique (TGA). Degradation temperatures are obtained from TGA experiments using the dynamic method, whereas isothermal TGA is used to determine the maximum operation temperature. The results show that, all the ILs present crystalline behaviour, with melting temperatures within the interval of 88 °C and 123 °C, whereas heat capacities linearly increases with temperature. A clear dependence with the anion is observed for both heat capacities and thermal stability, being ILs with the tosylate anion those presenting the highest values of molar heat capacities and the highest thermal stability.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Accuracy of refractive index spectroscopy by broadband interferometry

  • Arosa Lobato, Yago
  • Rodríguez-Fernández, Carlos Damián
  • Doval Casas, Alejandro
  • López Lago, María Elena
  • Fuente Carballo, Raúl de la
Uncertainties of refractive and group index in dispersion measurement by spectrally resolved white light interferometry are deeply analyzed. First, the contribution to uncertainty of the different parameters affecting both indices is identified. Afterwards, results are presented for a 1.5 mm thick fused silica sample over a broad spectral range, from 400 to 1000 nm, and the effects that mostly deteriorate the measurement accuracy are established. Finally, the different contributions are quadratically combined to determine the total uncertainty of the two indices
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Ecotoxicity of binary mixtures of ILs and inorganic salts of electrochemical interest

  • Parajó Vieito, Juan José
  • Vallet Moreno, Pablo
  • Varela Cabo, Luis Miguel
  • Villanueva López, María
  • Salgado Carballo, Josefa
The applicability of ionic liquids (ILs) has increased over the last years, and even new opportunities are becoming a reality, i.e. mixtures of pure IL and inorganic salt as electrolytes for smart electrochemical devices, yet the effects on the environment are almost unknown. In this work, the ecotoxicity of two pure protic ILs (Ethylammonium nitrate and Ethylimidazolium nitrate) and two pure aprotic ILs (butylmethylpyrrolidinium bis(trifluoromethylsulfonyl)imide and butyldimethylimidazolium bis(trifluoromethylsulfonyl)imide) and that of their binary mixtures with inorganic salts with common cation was tested towards changes in the bioluminescence of the bacteria Aliivibrio fischeri, using the Microtox® standard toxicity test. EC50 of these mixtures was determined over three standard periods of time and compared with the corresponding values to pure ILs. Results indicate that the aprotic ILs are more toxic than protic and that aromatic are more toxic than non-aromatic. The addition of inorganic mono (LiNO3), di (Ca(NO3)2·4H2O, Mg(NO3)2·6H2O) and trivalent (Al(NO3)3·9H2O) salts in binary mixtures with EAN was analysed first. The latter was found to induce an important increase in toxicity. Finally, mixtures of IL-inorganic lithium salt (LiNO3, for the protic ILs and LiTFSI for the aprotic ILs) toxicity was also studied, which showed toxicity levels strongly dependent on the IL of the mixture
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Non-additive electronic polarizabilities of ionic liquids: charge delocalization effects

  • Rodríguez-Fernández, Carlos Damián
  • López Lago, María Elena
  • Schröder, Christian
  • Varela Cabo, Luis Miguel
Electronic charge delocalization on the molecular backbones of ionic liquid-forming ions substantially impacts their molecular polarizabilities. Density functional theory calculations of polarizabilities and volumes of many cations and anions are reported and applied to yield refractive indices of 1216 ionic liquids. A novel expression for the precise estimation of the molecular volumes of the ionic liquids from simulation data is also introduced, adding quadratic corrections to the usual sum of atomic volumes. Our significant findings include i) that the usual assumption of uniform, additive atomic polarizabilities is challenged when highly mobile electrons in conjugated systems are present, and ii) that cations with conjugated large carbon chains can be used together with anions for the design of ionic liquids with very high refractive indices. A novel relation for the polarizability volume is reported together with a refractive index map made up of the studied ionic liquids
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Structure, dynamics and conductivities of ionic liquid-alcohol mixtures

  • Otero Mato, José Manuel
  • Montes-Campos, Hadrián
  • Gómez González, Víctor
  • Montoto, Martín
  • Cabeza Gras, Óscar
  • Kondrat, Svyatoslav
  • Varela Cabo, Luis Miguel
We study the microscopic structure and transport properties of ions in mixtures of 1-butyl-3-methylimidazolium and 1-butyl-3-ethylimidazolium iodide with ethanol using atomistic molecular dynamics simulations and conductivity measurements. Compared with the same ionic liquids in water, we reveal essential differences in ionic structure that are closely related to the differences in the solubility mechanisms of both types of solvents. In particular, unlike for aqueous solutions, we find a homogeneous distribution of solvent molecules in the system, i.e., we observe no cluster formation, which agrees with the nano-structured solvation paradigm. In addition, we calculate the conductivities of these systems in the whole concentration range and compare them with experimental data. Although the simulated values slightly underestimate the experimental ones, they reproduce the shape of the experimental conductivity dome reasonably well. We also show that the pseudo-lattice random-alloy model, which is based on microscopic ion jumping frequencies, describes the conductivity data accurately. We compute the average jumping frequencies directly from simulations and find that they agree well with those obtained by fitting the simulation conductivity data. These results show that the pseudo-lattice random-alloy model provides a valuable tool to describe the conductivities of ionic liquid–solvent mixtures and particularly their concentration dependence. It shall also apply to other systems, e.g., inorganic electrolytes and dispersed ionic conductors
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Density functional theory of alkali metals at the IL/graphene electrochemical interface

  • Montes-Campos, Hadrián
  • Rivera-Pousa, Alejandro
  • Méndez-Morales, Trinidad
The mechanism of charge transfer between metal ions and graphene in the presence of an ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate) is investigated by means of density functional theory calculations. For that purpose, two different comparisons are established: (i) the behavior of Li+ and K+ when adsorbed onto the basal plane of graphene and (ii) the differences between Li+ approaching the carbon surface from the basal plane and being intercalated through the edge plane of trilayer graphene. In the first case, it is found that the metal ions must overcome high energy barriers due to their interaction with the ionic liquid before reaching an equilibrium position close to the interface. In addition, no significant charge transfer between any of the metals and graphene takes place until very close energetically unfavorable distances. The second configuration shows that Li+ has no equilibrium position in the proximity of the interface but instead has an equilibrium position when it is inside the electrode for which it has to cross an energy barrier. In this case, the formation of a LiC12 complex is observed since the charge transfer at the equilibrium distance is achieved to a considerable extent. Thus, the interfacial charge transfer resistance on the electrode in energy devices based on ionic liquids clearly depends not only on the binding of the ionic liquid to the metal cations and their ability to form a dense solvation shell around them but also on the surface topography and its effect on the ion packing on the surface.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Role of Anions in 5-Hydroxymethylfurfural Solvation in Ionic Liquids from Molecular Dynamics Simulations

  • Montes-Campos, Hadrián
  • Méndez Morales, Trinidad
  • Varela Cabo, Luis Miguel
  • Ortuño Maqueda, Manuel Ángel
The proper selection of solvents for biomass upgrading is a crucial task as it should carefully balance the enhancement of reactivity with a facile product recovery. A challenging case is the conversion of glucose and fructose to 5-hydroxymethylfurfural (HMF). Ionic liquids (ILs) are often employed to boost the activity and selectivity of this process, although the isolation of HMF from the medium remains a major drawback. To investigate such solvent effects in a realistic (dynamic) environment, classical molecular dynamics (MD) simulations of HMF are performed in imidazolium-based ILs with different anions. Several parameters are identified that directly control HMF–anion interactions, which may hamper product separation, as well as HMF–HMF contacts, which can promote undesired side-reactions. These computational results would guide future high-throughput screenings of new and improved IL media
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

On the physical properties of mixtures of nitrate salts and protic ionic liquids

  • Vallet Moreno, Pablo
  • Bouzón Capelo, Silvia Diana
  • Méndez Morales, Trinidad
  • Gómez González, Víctor
  • Arosa Lobato, Yago
  • Fuente Carballo, Raúl de la
  • López Lago, María Elena
  • Rodríguez González, Julio Ramón
  • Gallego del Hoyo, Luis Javier
  • Parajó Vieito, Juan José
  • Salgado Carballo, Josefa
  • Turmine, Mireille
  • Segade Zas, Luisa María
  • Cabeza Gras, Óscar
  • Varela Cabo, Luis Miguel
We report a systematic study of the effect of salt concentration and its cation valence on several equilibrium and transport properties of mixtures of the model protic ionic liquid ethylammonium nitrate with monovalent (LiNO3), divalent (Mg(NO3)2 and Ca(NO3)2), and trivalent (Al(NO3)3) salts. These properties, determined by appropriate experimental techniques, include density, sound velocity, refractive index, surface tension, conductivity and viscosity. Single-particle dynamics and radial distribution functions were also analyzed by means of molecular dynamics simulations. The temperature dependence of the conductivity was studied in the Vogel-Fulcher-Tammann framework, and we obtained effective activation energies, fragility indexes, and Vogel temperatures. In addition, we performed a high-temperature Arrhenius analysis and we calculated the activation energies of both conductivity and viscosity. Finally, the exponents of the fractional Walden rule for the different mixtures were obtained and the ionicities and fragilities of the systems were analyzed, proving that all the mixtures are subionic and fragile. The distortion of the network of hydrogen bonds characteristic of protic ionic liquids and the formation of long-lived anionic aggregates composed of the cations of the added salt and the nitrate anions in their first solvation shell were found to have a deep impact on the analyzed properties. The role of the surface charge density of the salt cations on the structure and transport properties of the solutions is detailedly analyzed and related to solvation of salt species in the polar nanoregions of the ionic liquid (nanostructured solvation)
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

A new solid-state proton conductor: the salt hydrate based on imidazolium and 12-Tungstophosphate

  • Martinelli, Anna
  • Otero Mato, José Manuel
  • Garaga, Mounesha
  • Elamin, Khalid
  • Habibur Rahman, Seikh Mohammad
  • Zwanziger, Josef W.
  • Werner-Zwanziger, Ulrike
  • Varela Cabo, Luis Miguel
We report the structure and charge transport properties of a novel solid-state proton conductor obtained by acid–base chemistry via proton transfer from 12-tungstophosphoric acid to imidazole. The resulting material (henceforth named Imid3WP) is a solid salt hydrate that, at room temperature, includes four water molecules per structural unit. To our knowledge, this is the first attempt to tune the properties of a heteropolyacid-based solid-state proton conductor by means of a mixture of water and imidazole, interpolating between water-based and ionic liquid-based proton conductors of high thermal and electrochemical stability. The proton conductivity of Imid3WP·4H2O measured at truly anhydrous conditions reads 0.8 × 10–6 S cm–1 at 322 K, which is higher than the conductivity reported for any other related salt hydrate, despite the lower hydration. In the pseudoanhydrous state, that is, for Imid3WP·2H2O, the proton conductivity is still remarkable and, judging from the low activation energy (Ea = 0.26 eV), attributed to structural diffusion of protons. From complementary X-ray diffraction data, vibrational spectroscopy, and solid-state NMR experiments, the local structure of this salt hydrate was resolved, with imidazolium cations preferably orienting flat on the surface of the tungstophosphate anions, thus achieving a densely packed solid material, and water molecules of hydration that establish extremely strong hydrogen bonds. Computational results confirm these structural details and also evidence that the path of lowest energy for the proton transfer involves primarily imidazole and water molecules, while the proximate Keggin anion contributes with reducing the energy barrier for this particular pathway.
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Influence of Small Quantities of Water on the Physical Properties of Alkylammonium Nitrate Ionic Liquids

  • Ausín Neira, David
  • Parajó Vieito, Juan José
  • Trenzado, José Luis
  • Varela Cabo, Luis Miguel
  • Cabeza, Oscar
  • Segade, Luisa
This paper presents a comprehensive study of two alkylammonium nitrate ionic liquids. As part of this family of materials, mainly ethylammonium nitrate (EAN) and also propylammonium nitrate (PAN) have attracted a great deal of attention during the last decades due to their potential applications in many fields. Although there have been numerous publications focused on the measurement of their physical properties, a great dispersion can be observed in the results obtained for the same magnitude. One of the critical points to be taken into account in their physical characterization is their water content. Thus, the main objective of this work was to determine the degree of influence of the presence of small quantities of water in EAN and PAN on the measurement of density, viscosity, electrical conductivity, refractive index and surface tension. For this purpose, the first three properties were determined in samples of EAN and PAN with water contents below 30,000 ppm in a wide range of temperatures, between 5 and 95 °C, while the last two were obtained at 25 °C. As a result of this study, it has been concluded that the presence of water is critical in those physical properties that involve mass or charge transport processes, resulting in the finding that the absolute value of the average percentage change in both viscosity and electrical conductivity is above 40%. Meanwhile, refractive index (≤0.3%), density (≤0.5%) and surface tension (≤2%) present much less significant changes
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Structure, dynamics and ionic conductivities of ternary ionic liquid/lithium salt/DMSO mixtures

  • Martínez Crespo, Pablo
  • Otero Lema, Martín
  • Cabeza Gras, Óscar
  • Montes-Campos, Hadrián
  • Varela Cabo, Luis Miguel
In this paper we report classical Molecular Dynamics and ab initio Density Functional Theory simulations of the structure and single particle dynamics of ternary mixtures of a protic (ethylammonium nitrate, EAN) and an aprotic (1-Ethyl-3-methylimidazolium tetrafluoroborate, EMIMBF4) ionic liquid, lithium salts with common anion and a molecular cosolvent, dimethyl sulfoxide (DMSO). The coordination numbers and electrical conductivities of the different mixtures have been calculated throughout the whole concentration range, and the differences between mixtures with the protic and aprotic ionic liquids were analyzed. In both cases, the evolution of the electrical conductivity is seen to correlate well with the formation of mixed tetrahedral solvation complexes of lithium cations with ionic liquid anions and cosolvent molecules. The differences in the solvation and charge transport mechanisms in hydrogen bonded mixtures and those based in the aprotic ionic liquid are analyzed. Our conclusions indicate that the major feature behind the electrical conductivity of the ternary mixtures is the composition of the solvation shell of the metal cations in the mixtures and the rate at which anions in it are replaced by DMSO molecules
Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Thermophysical properties of n‑alkyl‑ammonium nitrate ionic liquids (n=2,3,4) pure and water saturated for energy applications

  • Parajó Vieito, Juan José
  • Vallet Moreno, Pablo
  • García Guimarey, María Jesús
  • Santiago Alonso, Antía
  • Teijeira Pernas, Tamara
  • Amigo Pombo, Alfredo José
  • Varela Cabo, Luis Miguel
  • Salgado Carballo, Josefa
  • Villanueva López, María
Phase transition temperatures of three ionic liquids (ILs) with ammonium cations of different alkyl chain length and nitrate common anion were determined in this paper by differential scanning calorimetry. Thermal stability of these ILs in air and nitrogen atmosphere and the maximum operation temperatures of the compounds were also studied using a thermogravimetric analyser. Furthermore, thermophysical properties as density, viscosity, thermal conductivity, and heat capacity against temperature of these pure ionic liquids were determined and compared with the corresponding values for water saturated samples. For this purpose, different techniques were employed: for density and viscosity a rotational automated viscodensimeter; for thermal conductivity measurements a thermal conductimeter that follows the transient hot-wire method; and for heat capacity measurements a microdifferential scanning calorimeter. Different behaviours were observed depending on the analysed thermophysical properties. In case of dried samples, density and thermal conductivity decrease with alkyl chain; for saturated samples, same tendency is observed for density but is the opposite in case of thermal conductivity. Isobaric specific heat and viscosity increase with alkyl chain length in case of dried samples; for saturated samples same tendency is observed for the viscosity, whereas the tendency is the contrary in case of isobaric specific heat
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Influence of metal salts addition on physical and electrochemical properties of ethyl and propylammonium nitrate

  • Ausín, David
  • Trenzado, José L.
  • Turmine, Mireille
  • Varela, Luis M.
  • Cabeza, Oscar
  • González Romero, Elisa
  • Segade Zas, MaríaLuisa
In this work, we deepen in the characterization of two protic ionic liquids (PILs), ethylammonium nitrate (EAN) and propylammonium nitrate (PAN). With this aim, we determined the influence of inorganic nitrate salts addition on their physical properties and their electrochemical potential window (EPW). Thus, experimental measurements of electrical conductivity, density, viscosity, refractive index and surface tension of mixtures of {EAN or PAN + LiNO3, Ca(NO3)2, Mg(NO3)2 or Al(NO3)3} at a temperature range between 5 and 95 °C are presented first, except for the last two properties which were measured at 25 °C. In the second part, the corresponding EPWs were determined at 25 °C by linear sweep voltammetry using three different electrochemical cells. Effect of the salt addition was associated mainly with the metal cation characteristics, so, generally, LiNO3 showed the lower influence, followed by Ca(NO3)2, Mg(NO3)2 or Al(NO3)3. The results obtained for the EAN + LiNO3 mixtures, along with those from a previous work, allowed us to develop novel predictive equations for most of the presented physical properties as functions of the lithium salt concentration, the temperature and the water content. Electrochemical results showed that a general order of EPW can be established for both PILs, although exceptions related to measurement conditions and the properties of the mixtures were found., Fundación Segundo Gil Dávila, Agencia Estatal de Investigación | Ref. MAT2017-89239-C2-1-P, Agencia Estatal de Investigación | Ref. MAT2017-89239-C2-2-P
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Ionogels Based on Protic Ionic Liquid - Lithium Salt Mixtures

  • Parajó, Juan José
  • Vallet Moreno, Pablo
  • Villanueva López, María
  • Cabeza, Óscar
  • Fernández Carretero, Francisco José
  • García-Luis, Alberto
  • Di Pietro, Maria Enrica
  • Mele, Andrea
  • Castiglione, Franca
  • Salgado, Josefa
  • Varela, Luis M.
[Abstract] The effect of the addition of lithium nitrate on the liquid range and electrical conductivity of mixtures of a protic ionic liquid, ethylammonium nitrate (EAN) with LiNO3 is reported in this work. Moreover, changes in these properties upon confinement in silica-based matrices are also analysed and related to variations on the microstructure of the mixtures. Our results show that gelation of the mixtures induces amorphous behaviour in all the samples, but no significant changes in the thermal stability are detected. However, important differences on the electrical conductivity of the liquid and gel states of the mixtures were observed. While this magnitude decreases with the addition of salt in the liquid samples for all the temperatures it increases at low concentrations of LiNO3 up to a maximum in the gelled samples with the lowest concentration of added salt (0.1 mol of salt by kg of EAN). High resolution magic angle spinning (HRMAS) NMR shows that the addition of lithium nitrate increases the mobility (both rotational and translational motion) of the cation EA+ within the ionogel and the diffusion of the cation provides evidence of the presence of two different populations of the same molecules experiencing two distinct apparent diffusion coefficients (bi-exponential decay of magnetization in diffusion NMR experiments), while it is mono-exponential in the pure ionic liquid. The Li+ cation is shown to display a higher mobility (both rotational and translational motion) in the ionogel than in the neat ionic liquid. The frustration of the formation of solvation complexes due to the confinement is suspected to be behind this behaviour., Authors acknowledge M. Gómez (RIAIDT-USC) for the technical support in DSC measurements. This work was supported by Spanish Ministry of Economy and Competitiveness and FEDER Program through the projects MAT2017-89239-C2-1-P and MAT2017-89239-C2-2-P and the SISE Network RED2018-102679-T as well as by Xunta de Galicia through GRC ED431C 2020/10 project and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06. P. Vallet and J. J. Parajó thank funding support of FPI Program from Spanish Ministry of Science, Education and Universities and I2C postdoctoral Program of Xunta de Galicia, respectively, Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED431D 2017/06
RUC. Repositorio da Universidade da Coruña
Publicación Contribución de congreso (ConferenceOutput)

Ionogels: Polimeric and Sol-Gel Silica Nanoscaffolds of Ionic Liquids as Smart Materials

  • Santiago Alonso, Antía
  • Vallet Moreno, Pablo
  • Parajó, Juan José
  • Villanueva López, María
  • Cabeza, Óscar
  • Varela, Luis M.
  • Salgado, Josefa
Presented at the 26th International Electronic Conference on Synthetic Organic Chemistry, 15–30 November 2022; Available online: https://sciforum.net/event/ecsoc-26., [Abstract] The purpose of this work is to check the viability of mixtures of ionic liquids and lithium salt as electrolytes in Li- batteries. Firstly, the determination of the thermo-electrical properties of liquid mixtures of the ionic liquid N-butyl-N-methyl-pyrrolidinium bis(trifluoromethanesulfonyl)imide [BMPyrr][TFSI] with [Li][TFSI] salt at different concentrations was performed. Additionally, these results were compared with the corresponding ionogels of these mixtures designed by two different gelation methods, one of them using Poly (vinylidene fluoride) (PVDF) as a supporting matrix and the other one using a silica matrix., This work was supported by Spanish Ministry of Economy and Competitiveness and FEDER Program through the project MAT2017-89239-C2-1-P and the Network Ionic Systems for energy sustainability (SISE) RED2018-102679-T and by Xunta de Galicia through GRC ED431C 2020/10 project and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06, Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED431D 2017/06, https://sciforum.net/event/ecsoc-26
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Preliminary Study of New Electrolytes Based on [MPPyr][TFSI] for Lithium Ion Batteries

  • García-Garabal, Sandra
  • Domínguez-Pérez, Montserrat
  • Portela, Dafne
  • Varela, Luis M.
  • Cabeza, Óscar
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] The application of ionic liquids in lithium ion batteries has increased in recent years in order to find new electrolytes that improve both performance and safety. The gathering of experimental data in order to understand the behaviour of these systems will help us design electrolytes that can be optimized for a specific objective. Data on electrolytes made up of a ternary mixture with an ionic liquid are missing in the literature. In this work, we provide new data on physical properties and refractive indexes for the ternary mixtures 1-methyl-1-propylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([MPPyr][TFSI]) + acetonitrile (AN) or γ butyrolactone (GBL) or dimethyl sulfoxide (DMSO) + lithium bis(trifluoromethylsulfonyl)imide (LiTFSI) with different concentrations of salt, specifically, 10%, 15%, 20%, 30%, 35%. The measured properties were density (ρ), viscosity (η) and ionic conductivity (κ) in the temperature range of 278.15 to 358.15 K except for the mixtures with acetonitrile whose temperature range was 278.15 K to 328.15 K and the refractive indexes (nD) that were measured at a single temperature of 298.15 K. In general, the addition of salt in the binary mixtures provokes an increase of density and viscosity and therefore a decrease of ionic conductivity. It is worth mentioning that some of the studied systems showed values of ionic conductivity even better than those obtained for electrolyte systems based on carbonate., This work was supported by Ministerio de Economia y Competitividad (MINECO) and FEDER Program through the projects MAT2017–89239-C2–1-P, MAT2017–89239-C2–2-P and D2018–102679-T; Xunta de Galicia. Funding for open access charge: Universidade da Coruña/CISUG
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Experimental Device to Measure the Ionic Conductivity Anisotropy in Liquid Crystal Hydrogel Based In [EMIM] Alkyl Sulfate Ionic Liquids

  • Portela, Dafne
  • Segade, Luisa
  • Arosa, Yago
  • López Lago, Elena
  • Varela, Luis M.
  • Tojo, Emilia
  • Cabeza, Óscar
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, [Abstract] We have built an experimental device with the aim to measure the expected electrical conductivity anisotropy in a liquid crystal, obtained from the gelation of the ionic liquid 1-ethyl-3-methyl imidazolium decyl sulfate, [EMIM][DSO4]. This ionic liquid has the particularity that it transits to a semi-solid gel state at room temperature when it contains water, naturally adsorbed from the environment until a balance is reached between the concentration of water in the IL and the atmospheric humidity grade. The quantity of water adsorbed to form the hydrogel at room temperature varies from about 5 to 30 wt%, each composition giving place to different smectic phases. In the gel state, the ionic liquid ions and the water molecules self-organize into micro-sized mesophases that resemble the structures of a liquid crystal. Our device is a closed 2D sample holder (with sides 150 times longer than its thickness), with a single narrow window open to the atmosphere, and four copper contacts on the sides. The dried ionic liquid is tempered at 40 °C to increase its fluidity when injected into the cavity, and then, it can only adsorb water through the narrow opening. Thus, water adsorption is unidirectional and slow, so the transition of the IL to the gel phase happens progressively. A metastable giant mesophase appears as an orientated macrodomain in the form of a striped pattern. In this state, we measure the electrical conductivity of the confined film in directions parallel and perpendicular to the observed strips, finding a difference of up to 26% between both values of the conductivity. If the sample freezes (below 10 °C) or it liquefies (above 50 °C) the meso structure is broken and the observed anisotropy destroyed. We can return the sample to gel state by varying the temperature, but the ordered macroscopic state is no longer recovered. This research must give clues to solve the charge transport mechanism quiz in ionic liquids and semi-solid coductors., This work was supported by Ministerio de Economia y Competitividad (MINECO) and FEDER Program through the projects MAT2017–89239-C2–1-P, MAT2017–89239-C2–2-P and RED2018–102679-T; Xunta de Galicia and FEDER (GRC 508 ED431C 2020/10). Funding for open access charge: Universidade da Coruña/CISUG, Xunta de Galicia; GRC 508 ED431C 2020/10
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Strange Behaviour of Transport Properties in Novel Metal Thiocyanate Based Ionic Liquids

  • Cabeza, Óscar
  • Segade, Luisa
  • Domínguez-Pérez, Montserrat
  • Rilo, Esther
  • Ausín, David
  • Seijas, Julio A.
  • Vázquez-Tato, M. Pilar
  • Matveev, Vladimir V.
  • Ievlev, A.V.
  • Salgado, Josefa
  • Varela, Luis M.
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, The following are the Supplementary data to this article: https://ars.els-cdn.com/content/image/1-s2.0-S0167732221018882-mmc1.docx, [Abstract] In a previous paper some of us presented the structure and some properties of a new family of ionic liquids, ILs, with a common cation, 1-butyl-3-methyl imidazolium (the popular [C4C1Im]⁺ or [BMIM]⁺) and a variety of anions based in thiocyanate (SCN)¯: one reference sample and ten with anionic metal complexes of different valences: Al¹¹¹, Mn¹¹, Fe¹¹, Cr¹¹¹, Ni¹¹, Hg¹¹, Zn¹¹, Co¹¹ and Cu¹, resulting, respectively, [BMIM](SCN), [BMIM]₃ Al(SCN)₆, [BMIM]₄ Mn(SCN)₆, [BMIM]₃ Fe(SCN)₆, [BMIM]₃ Cr(SCN)₆, [BMIM]₄ Ni(SCN)₆, [BMIM]₂ Hg(SCN)₄, [BMIM]₂ Zn(SCN)₄, [BMIM]₂ Co(SCN)₄ and [BMIM]₃ Cu(SCN)₄. In this paper we show experimental measurements of electrical conductivity of these ILs in a broad temperature range (about 90 K). Viscosity has been measured for six compounds in a wide temperature range. In addition, the diffusion coefficient for both ions forming the IL has been measured for some of the samples using NMR-Dosy technique. In spite of being very similar compounds from a chemical point of view, they present very different transport property values. Thus, viscosity varies more than two orders of magnitude among those metal thiocyanate ILs, being the highest for the compound with Al and the lowest for that with Hg. Moreover, differences between ionic conductivity and diffusion coefficient values extend more than one order of magnitude among the thiocyanate ILs. These three properties will be related in pairs, thus through Walden’s rule we compare molar conductivity and fluidity, while using Kohlrausch’s law and Nerst-Einstein equation molar conductivity and diffusion coefficient are related. Also, diffusion coefficient and fluidity (the inverse of viscosity) are compared by means of Stokes-Einstein relationship. In addition, we calculate the Laity interionic friction coefficients for both anions of the IL with Hg. Finally, a theoretical model is suggested to explain all the experimental evidences reported., We acknowledge the financial support of Ministerio de Economía y Competitividad MINECO) (MAT2017-86109-P and MAT2017-89239-C2-(1.2)-P); and Xunta de Galicia (AGRU 015/11. GRC ED431C 2016/001 and ED431D 2017/06). All these research projects were partially supported by FEDER. Also, D.A. acknowledges Gil Dávila Foundation for his postgraduate grant. Funding for open access charge: Universidade da Coruña/CISUG., Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431D 2017/06, https://ars.els-cdn.com/content/image/1-s2.0-S0167732221018882-mmc1.docx
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Synthesis, Microstructure and Volumetry of Novel Metal Thiocyanate Ionic Liquids With [BMIM] Cation

  • Cabeza, Óscar
  • Varela, Luis M.
  • Rilo, Esther
  • Segade, Luisa
  • Domínguez-Pérez, Montserrat
  • Ausín, David
  • Pedro, Manuel de
  • Rodríguez Fernández, Jesús
  • González, Jesús Antonio
  • Vázquez-Tato, M. Pilar
  • Arosa, Yago
  • López Lago, Elena
  • Fuente, Raúl de la
  • Parajó, Juan José
  • Salgado, Josefa
  • Villanueva López, María
  • Matveev, Vladimir V.
  • Ievlev, A.V.
  • Seijas, Julio A.
This is an accepted version of the published document., [Abstract] We present a new family of ionic liquids (ILs) with a common cation, 1-butyl-3-methyl imidazolium, the popular [BMIM]+ (also written C4C1Im+) and a variety of anionic complexes (also called adducts) based in thiocyanate (SCN)−: one blank compound, BMIM(SCN), and ten doped with metals having different oxidation states: Al+3, Mn+2, Fe+3, Cr+3, Ni+2, Hg+2, Zn+2, Co+2, Cd+2 and Cu+, forming, respectively, [BMIM]3[Al(SCN)6], [BMIM]4 Mn(SCN)6, [BMIM]3 Fe(SCN)6, [BMIM]3 Cr(SCN)6, [BMIM]4 Ni(SCN)6, [BMIM]2 Hg(SCN)4, [BMIM]2 Zn(SCN)4, [BMIM]2 Co(SCN)4, [BMIM]2 Cd(SCN)4 and [BMIM]3 Cu(SCN)4. All of them were synthesized by us, except the blank IL and the Co thiocyanate, which are commercial. Obtained products have been characterized by NMR, and also by electrospray ionization, MS-ES, which allows the determination of the new ILs purities. Then, compounds have been analyzed using FT-IR and Raman spectroscopy. In addition, magnetic susceptibility and refractive index measurements were performed in some of the compounds studied, as well as thermal characterization using DSC and TGA. Finally, experimental measurements of density on all those ILs have been performed, and for some of the samples in a broad temperature range (about 100 K). In spite of being very similar compounds from the chemical point of view, they present quite different physical properties, including optical, thermal and magnetic ones… Also, they show different oxidation states (one with +1, six with +2 and other three with +3). We guess that this family of ILs will have interesting applications, mainly for photonic devices., We acknowledge fruitful comments with our colleague Dr. A. Macías from USC. We also acknowledge the financial support of Ministerio de Economía y Competitividad (MINECO) (MAT2014-57943-C3-(1-3)-P and MAT2017-89239-C2-(1,2)-P); Xunta de Galicia (AGRU 2015/11, GRC ED431C 2016/001 and ED431D 2017/06, ED431E 2018/08). All these last research projects were partially supported by FEDER, Xunta de Galicia; AGRU 2015/11, Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431D 2017/06, Xunta de Galicia; ED431E 2018/08
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Anomalous Behaviour of the Ionic Conductivity of Nanoconfined IL -Lithium Salt Mixtures

  • Vallet Moreno, Pablo
  • Parajó, Juan José
  • Santiago Alonso, Antía
  • Villanueva López, María
  • Cabeza, Óscar
  • Varela, Luis M.
  • Salgado, Josefa
[Abstract] The effect of salt addition on the protic ionic liquid (IL) ethylimidazolium nitrate is analysed in this work in terms of structural changes measured by NMR, thermal behaviour and ionic conductivity. Additionally, the effect of the immobilization of these mixtures in nano-silica structures on the same properties is also studied. Results show that the influence of salt on the chemical shifts of the signals associated to hydrogen atoms in the apolar regions of the ionic liquid is almost negligible, both in liquid and gel states. The salt accommodates in the polar region of the IL, according to the nanostructured solvation paradigm. The liquid range increases with salt concentration in both states, being this effect especially interesting for high and low temperature applications. The ionic conductivity takes appropriate values to use these compounds as electrolytes in electrochemical devices; pure IL presents 6.9 mS·cm−1 at 298 K rising to 17.38 mS·cm−1 at 323 K and this property decreases with salt concentration in the liquid state, as can be expected. Although gel samples present lower ionic conductivity than liquid samples, an anomalous behaviour can be observed in the ionogel samples upon the salt concentration, characterized by an absolute maximum, 13.26 mS·cm−1 at 323 K, at the lowest salt concentration (0.5 mol·kg−1 of Li+ salt addition), which represents the 12 % higher than the corresponding values of pure ionogel at this temperature., Authors acknowledge M. Gómez and M. Martín-Pastor (RIAIDT-USC) for their technical support in DSC and NMR measurements, respectively. This work was founded by Spanish Ministry of Economy and Competitiveness and FEDER Program through the project MAT2017-89239-C2. Vallet, J. J. Parajó and A. Santiago-Alonso thank funding support of FPI Program from Spanish Ministry of Science, Education and Universities, I2C postdoctoral and predoctoral Programs of Xunta de Galicia, respectively
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Electrical Conductivity and Nyquist Plot of C₄C₁Im BF₄ at Room Temperature by Impedance Spectroscopy

  • Vallet Moreno, Pablo
  • Parajó, Juan José
  • Sotuela, Félix
  • Morcillo, Ángel
  • Villanueva López, María
  • Cabeza, Óscar
  • Varela, Luis M.
  • Salgado, Josefa
[Abstract] Ionic liquids (ILs) represent a real alternative for electrochemical applications due to their remarkable characteristics, namely a very low vapour pressure, low flammability, high thermal stability, wide potential window and high ionic conductivity. In this work, Nyquist plot and impedance spectroscopy at room temperature is proposed as an alternative method to obtain the ionic conductivity for ionic liquids by using an Agilent HP 4284A RLC precision meter. For this propose, the IL 1-butyl-3-methylimidazolium tetrafluoroborate (C₄C₁Im BF₄) was selected and results were compared with the previously obtained from the conductimeter CRISON GLP31., This work was supported by Spanish Ministry of Economy and Competitiveness and FEDER Program through the project MAT2017-89239-C2-1-P and by Xunta de Galicia through GRC ED431C 2020/10 project and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06. P. Vallet and J. J. Parajó thank funding support of FPI Program from Spanish Ministry of Science, Education and Universities and I2C postdoctoral Program of Xunta de Galicia, respectively, Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED431D 2017/06
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Structure, Dynamics and Conductivities of Ionic Liquid-Alcohol Mixtures

  • Otero-Mato, José M.
  • Montes-Campos, Hadrián
  • Gómez-González, Víctor
  • Montoto, Martín
  • Cabeza, Óscar
  • Kondrat, Svyatoslav
  • Varela, Luis M.
[Abstract] We study the microscopic structure and transport properties of ions in mixtures of 1-butyl-3-methylimidazolium and 1-butyl-3-ethylimidazolium iodide with ethanol using atomistic molecular dynamics simulations and conductivity measurements. Compared with the same ionic liquids in water, we reveal essential differences in ionic structure that are closely related to the differences in the solubility mechanisms of both types of solvents. In particular, unlike for aqueous solutions, we find a homogeneous distribution of solvent molecules in the system, i.e., we observe no cluster formation, which agrees with the nano-structured solvation paradigm. In addition, we calculate the conductivities of these systems in the whole concentration range and compare them with experimental data. Although the simulated values slightly underestimate the experimental ones, they reproduce the shape of the experimental conductivity dome reasonably well. We also show that the pseudo-lattice random-alloy model, which is based on microscopic ion jumping frequencies, describes the conductivity data accurately. We compute the average jumping frequencies directly from simulations and find that they agree well with those obtained by fitting the simulation conductivity data. These results show that the pseudo-lattice random-alloy model provides a valuable tool to describe the conductivities of ionic liquid–solvent mixtures and particularly their concentration dependence. It shall also apply to other systems, e.g., inorganic electrolytes and dispersed ionic conductors., The financial support of the Spanish Ministry of Economy and Competitiveness (Projects MAT2017-89239-C2-1-P and MAT2017-89239- C2-2-P) is gratefully acknowledged. Moreover, this work was funded by the Xunta de Galicia (ED431D 2017/06, ED431E 2018/08, GRC ED431C 2016/001 and GRC ED431C 2020/10). All these research projects were partially supported by FEDER. The help of the technician M. C. V. from UDC for some of the measurements presented is also acknowledged. H. M-C. and J. M. O-M. thank the Spanish Ministry of Education for their FPU grant, and H. M-C. thanks the USC for his “Convocatoria de Recualificación do Sistema Universitario Español-Margarita Salas” postdoc grant under the “Plan de Recuperación Transformación” program funded by the Spanish Ministry of Universities with European Union’s NextGenerationEU funds, Xunta de Galicia; ED431D 2017/06, Xunta de Galicia; ED431E 2018/08, Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431C 2020/10
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Effect of Gold Nanoparticles on Transport Properties of the Protic Ionic Liquid Propylammonium Nitrate

  • García-Garabal, Sandra
  • Domínguez-Pérez, Montserrat
  • Cabeza, Óscar
  • Arosa, Yago
  • Varela, Luis M.
  • Fernández-López, Cristina
  • Pérez-Juste, Jorge
  • Pastoriza-Santos, Isabel
Financiado para publicación en acceso aberto: Universidade da Coruña/CISUG, The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.jced.1c00135, [Abstract] Here, we analyze the effect of gold-nanoparticle (AuNPs)-doping of the protic ionic liquid (IL) propyl ammonium nitrate (PAN) on some physical properties, such as density, viscosity, and ionic conductivity, in a broad temperature range. This IL was lightly doped with four different AuNPs (concentration of gold lower than 0.2 mM): Au nanospheres of about 15, 60, and 80 nm diameter and Au nanorods of about 40 nm length and 12 nm width. AuNPs were synthesized following a seed growth approach and further functionalized with O-[2-(3-mercapto propionylamino)ethyl] O′-methyl-poly(ethylene glycol) (m-PEG-SH) in order to provide stability to the IL medium. The stability of the AuNPs in PAN was characterized by UV–vis spectroscopy. The results obtained here indicate that their presence produces a strong influence on the measured transport properties of PAN, decreasing viscosity up to 25% and increasing ionic conductivity up to 10% for the smallest AuNPs. Moreover, as temperature increases, the influence of AuNPs produces a decrease in the percentage deviations for viscosity and ionic conductivity. In the case of density, the AuNP-doping produces a mainly unexpected increase only for the sample with the smallest AuNPs, that is practically constant with temperature. When we equalize the AuNP concentration for all sizes and shapes, it is observed that the smallest AuNPs give higher variations in the studied properties than the bigger ones; also, the shape of the rod has an influence on the measured results. In addition, we have applied Walden’s rule to relate the three measured magnitudes, observing that AuNP addition decreases ionicity with respect to the reference sample, which is even more when we added smaller AuNPs. Finally, we explain all data assuming cation solvation of the AuNPs, which creates a local breaking of the pseudolattice structure of the PAN. Comparison with other published data is difficult because the behavior of a nanoparticle solution strongly depends on its particular composition and no data are available, in our knowledge, of any similar mixture to those studied here., The financial support of Ministerio de Economía y Competitividad (MINECO) (MAT2016-77809-R and MAT2017-89239-C2-(1,2)-P); Xunta de Galicia (GRC ED431C 2016/001 and ED431D 2017/06) is also acknowledged. All these research projects were partially supported by FEDER, Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431D 2017/06, https://pubs.acs.org/doi/suppl/10.1021/acs.jced.1c00135/suppl_file/je1c00135_si_001.pdf
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Influence of Metal Salts Addition on Physical and Electrochemical Properties of Ethyl and Propylammonium Nitrate

  • Ausín, David
  • Trenzado Diepa, José Luis
  • Turmine, Mireille
  • Varela, Luis M.
  • Cabeza, Óscar
  • González-Romero, Elisa
  • Segade, Luisa
[Abstract] In this work, we deepen in the characterization of two protic ionic liquids (PILs), ethylammonium nitrate (EAN) and propylammonium nitrate (PAN). With this aim, we determined the influence of inorganic nitrate salts addition on their physical properties and their electrochemical potential window (EPW). Thus, experimental measurements of electrical conductivity, density, viscosity, refractive index and surface tension of mixtures of {EAN or PAN + LiNO3, Ca(NO3)2, Mg(NO3)2 or Al(NO3)3} at a temperature range between 5 and 95 °C are presented first, except for the last two properties which were measured at 25 °C. In the second part, the corresponding EPWs were determined at 25 °C by linear sweep voltammetry using three different electrochemical cells. Effect of the salt addition was associated mainly with the metal cation characteristics, so, generally, LiNO3 showed the lower influence, followed by Ca(NO3)2, Mg(NO3)2 or Al(NO3)3. The results obtained for the EAN + LiNO3 mixtures, along with those from a previous work, allowed us to develop novel predictive equations for most of the presented physical properties as functions of the lithium salt concentration, the temperature and the water content. Electrochemical results showed that a general order of EPW can be established for both PILs, although exceptions related to measurement conditions and the properties of the mixtures were found., This research was funded by the Spanish Ministry of Economy, Industry and Competitiveness, grant numbers MAT2017-89239-C2-1-P and MAT2017-89239-C2-2-P. D. Ausín thanks the funding support of Fundación Segundo Gil Dávila
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Determination of Thermophysical Properties of the Protic Ionic Liquid EIM NO₃, Pure and Doped with Lithium Nitrate Salt

  • Vallet Moreno, Pablo
  • Parajó, Juan José
  • Cabeza, Óscar
  • Varela, Luis M.
  • Salgado, Josefa
  • Villanueva López, María
[Abstract] In this work, viscosity, density and electrical conductivity of the ionic liquid, Ethylimidazolium Nitrate pure and doped with lithium nitrate salt were determined in order to check the properties’ improvement of the ionic liquid with the salt addition to consider these mixtures as potential electrolytes. Viscosity decreases exponentially as temperature increases, and increases with salt content, as expected. Density values decrease linearly as temperature increases and also increases with salt content. From electrical studies, an increase of conductivity with temperature and a decrease with salt concentration were observed. No significant differences between pure and doped sample were observed on Walden plots., This work was supported by Spanish Ministry of Economy and Competitiveness and FEDER Program through the projects MAT2014-57943-C3-1-P, MAT2014-57943-C3-3-P, MAT2017-89239-C2-1-P, as well as by Xunta de Galicia through GRC ED431C 2020/10 project and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06. P. Vallet and J. J. Parajó thank funding support of FPI Program from Spanish Ministry of Science, Education and Universities and I2C postdoctoral Program of Xunta de Galicia, respectively, Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED431D 2017/06
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Thermal Behaviour of Ionogels Based on Ionic Liquid Lithium Salt Mixtures

  • Parajó, Juan José
  • Vallet Moreno, Pablo
  • Fernández Míguez, Lois
  • Villanueva López, María
  • Cabeza, Óscar
  • Varela, Luis M.
  • Salgado, Josefa
Presented at the 24th International Electronic Conference on Synthetic Organic Chemistry, 15 November–5 December 2020; Available online: https://ecsoc-24.sciforum.net/, [Abstract] The thermal behavior of the mixtures of two protic ionic liquids (ethylammonium nitrate (EAN) and ethylimidazolium nitrate ([EIm][NO3])) with lithium nitrate salt (LiNO3), and one aprotic ionic liquid (butyl methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([BMpyrr][TFSI)) with lithium bis(trifluoromethylsulfonyl)imide salt (LiTFSI), at different concentrations, was studied in this work using a Differential Scanning Calorimeter (DSC-Q2000-TA Instruments). Comparisons with the thermal behavior of silica-based ionogels of these mixtures were also performed., This work was supported by Spanish Ministry of Economy and Competitiveness and FEDER Program through the projects MAT2014-57943-C3-1-P, MAT2014-57943-C3-3-P, MAT2017-89239-C2-1-P as well as by Xunta de Galicia through GRC ED431C 2020/10 project and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06. P. Vallet and J. J. Parajó thank funding support of FPI Program from Spanish Ministry of Science, Education and Universities and I2C postdoctoral Program of Xunta de Galicia, respectively., Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED431D 2017/06, https://sciforum.net/paper/view/8371
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

On the Physical Properties of Mixtures of Nitrate Salts and Protic Ionic Liquids

  • Vallet Moreno, Pablo
  • Bouzón-Capelo, Silvia
  • Méndez-Morales, Trinidad
  • Gómez-González, Víctor
  • Arosa, Yago
  • de la Fuente, Raúl
  • López Lago, Elena
  • Rodríguez, Julio R.
  • Gallego, Luis J.
  • Parajó, Juan José
  • Salgado, Josefa
  • Turmine, Mireille
  • Segade, Luisa
  • Cabeza, Óscar
  • Varela, Luis M.
[Abstract] We report a systematic study of the effect of salt concentration and its cation valence on several equilibrium and transport properties of mixtures of the model protic ionic liquid ethylammonium nitrate with monovalent (LiNO3), divalent (Mg(NO3)2 and Ca(NO3)2), and trivalent (Al(NO3)3) salts. These properties, determined by appropriate experimental techniques, include density, sound velocity, refractive index, surface tension, conductivity and viscosity. Single-particle dynamics and radial distribution functions were also analyzed by means of molecular dynamics simulations. The temperature dependence of the conductivity was studied in the Vogel-Fulcher-Tammann framework, and we obtained effective activation energies, fragility indexes, and Vogel temperatures. In addition, we performed a high-temperature Arrhenius analysis and we calculated the activation energies of both conductivity and viscosity. Finally, the exponents of the fractional Walden rule for the different mixtures were obtained and the ionicities and fragilities of the systems were analyzed, proving that all the mixtures are subionic and fragile. The distortion of the network of hydrogen bonds characteristic of protic ionic liquids and the formation of long-lived anionic aggregates composed of the cations of the added salt and the nitrate anions in their first solvation shell were found to have a deep impact on the analyzed properties. The role of the surface charge density of the salt cations on the structure and transport properties of the solutions is detailedly analyzed and related to solvation of salt species in the polar nanoregions of the ionic liquid (nanostructured solvation)., The financial support of the Spanish Ministry of Economy and Competitiveness (Projects MAT2017-89239-C2-1-P and MAT2017-89239- C2-2-P) is gratefully acknowledged. Moreover, this work was funded by the Xunta de Galicia (ED431D 2017/06, ED431E 2018/08, GRC ED431C 2016/001 and GRC ED431C 2020/10). All these research projects were partially supported by FEDER. P. V. thanks the Spanish Ministry of Science, Innovation and Universities for his FPI grant (PRE2018-084212). T.M.-M. thanks the Spanish Ministry of Science, Innovation and Universities for her Juan de la Cierva grant (IJC2018-036774-I).J. J. Parajó thanks the funding support of I2C postdoctoral program of Xunta de Galicia. Y. A. thanks the funding support from postdoctoral Program of Xunta de Galicia (ED481B-2021-027). Facilities provided by the Galician Supercomputing Centre (CESGA) are also acknowledged, Xunta de Galicia; ED431D 2017/06, Xunta de Galicia; ED431E 2018/08, Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED481B-2021-027
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Structure, Dynamics and Ionic Conductivities of Ternary Ionic Liquid/Lithium Salt/DMSO Mixtures

  • Martínez-Crespo, Pablo
  • Otero-Lema, Martín
  • Cabeza, Óscar
  • Montes-Campos, Hadrián
  • Varela, Luis M.
[Abstract] In this paper we report classical Molecular Dynamics and ab initio Density Functional Theory simulations of the structure and single particle dynamics of ternary mixtures of a protic (ethylammonium nitrate, EAN) and an aprotic (1-Ethyl-3-methylimidazolium tetrafluoroborate, EMIMBF4) ionic liquid, lithium salts with common anion and a molecular cosolvent, dimethyl sulfoxide (DMSO). The coordination numbers and electrical conductivities of the different mixtures have been calculated throughout the whole concentration range, and the differences between mixtures with the protic and aprotic ionic liquids were analyzed. In both cases, the evolution of the electrical conductivity is seen to correlate well with the formation of mixed tetrahedral solvation complexes of lithium cations with ionic liquid anions and cosolvent molecules. The differences in the solvation and charge transport mechanisms in hydrogen bonded mixtures and those based in the aprotic ionic liquid are analyzed. Our conclusions indicate that the major feature behind the electrical conductivity of the ternary mixtures is the composition of the solvation shell of the metal cations in the mixtures and the rate at which anions in it are replaced by DMSO molecules., The financial support of the Spanish Ministry of Economy and Competitiveness (Projects MAT2017-89239-C2-1-P, MAT2017-89239-C2-2-P) is gratefully acknowledged. Moreover, this work was funded by the Xunta de Galicia (ED431E 2018/08 and GRC 369 ED431C 2020/10). All these research projects were partially supported by FEDER. H. M-C. thanks the USC for his “Convocatoria de Recualificación del Sistema Universitario Español-Margarita Salas” postdoc grant under the “Plan de Recuperación, Transformación y Resiliencia” program funded by the Spanish Ministry of Universities with European Union’s NextGenerationEU funds, Xunta de Galicia; ED431E 2018/08, Xunta de Galicia; GRC 369 ED431C 2020/10
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Thermophysical Characterization of TFSI Based Ionic Liquid and Lithium Salt Mixtures

  • Fernández-Míguez, Lois
  • Vallet Moreno, Pablo
  • Tasende-Rodríguez, Lucía Camila
  • Doval, Alejandro
  • Villanueva López, María
  • Cabeza, Óscar
  • Varela, Luis M.
  • Salgado, Josefa
  • Parajó, Juan José
Este artigo pertence ás actas do The 23rd International Electronic Conference on Synthetic Organic Chemistry., [Abstract] The ionic liquids (ILs) doped with metal salts have become a real alternative as electrolytes for batteries, but the right choice of these compounds for reaching the adequate properties and performance is still a challenge, and strategies are therefore needed for achieving it. The thermophysical properties of IL 1-butyl-1-methylpyrrolidinium bis[(trifluoromethyl)sulfonyl]imide ([bmpyr] [TFSI]) and its mixture with bis-(trifluoromethane)-sulfonimide lithium salt (from 0.1 m to saturation level) were determined in this work. These properties are density (ρ), speed of sound (U), and corresponding derived magnitudes, such as the bulk modulus and the thermal coefficient, as well as electrical conductivity (σ) against temperature. Density shows a linear decreasing dependence with temperature and a clear increase with the addition of salt, whereas the thermal expansion coefficient increases with temperature and salt addition. Speed of sound decreases with both temperature and salt concentration, and the adiabatic compressibility calculated by means of the well-known Laplace equation increases, as expected, with temperature in all the studied cases, although a small variation with concentration was observed. Electrical conductivity increases with temperature following the Vogel–Fulcher–Tammann (VFT) equation and decreases with the addition of salt., This research was funded by the Spanish Ministry of Economy and Competitiveness and FEDER (Fondo Europeo de Desarrollo Regional) Program through the projects MAT2014-57943-C3-1-P, MAT2014-57943-C3-3-P, MAT2017-89239-C2-1-P as well as by Xunta de Galicia through the GRC (Grupo de Referencia Competitiva) ED431C 2016/001 project, and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06. P. Vallet and J. J. Parajó are thankful for funding support from the FPI (Formación de Personal Investigador) Program from the Spanish Ministry of Science, Education and Universities and I2C postdoctoral Program of Xunta de Galicia, respectively., Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431D 2017/06
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Accuracy of refractive index spectroscopy by broadband interferometry

  • Rodríguez-Fernández, Carlos Damián
  • Arosa, Yago
  • Doval, Alejandro
  • López Lago, Elena
  • Fuente, Raúl de la
[Abstract] Uncertainties of refractive and group index in dispersion measurement by spectrally resolved white light interferometry are deeply analyzed. First, the contribution to uncertainty of the different parameters affecting both indices is identified. Afterwards, results are presented for a 1.5 mm thick fused silica sample over a broad spectral range, from 400 to 1000 nm, and the effects that mostly deteriorate the measurement accuracy are established. Finally, the different contributions are quadratically combined to determine the total uncertainty of the two indices., The financial support of the Spanish Ministry of Economy and Competitiveness through the coordinated grants MAT2017-89239-C2-1-P is gratefully acknowledged. Moreover, this work was funded by the Xunta de Galicia and FEDER (ED431D 2017/06, ED431E2018/08, GRC 508 ED431C 2020/10)., Xunta de Galicia ; ED431D 2017/06, Xunta de Galicia ; ED431E2018/08, Xunta de Galicia ; GRC 508 ED431C 2020/10
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Random-Alloy Model for the Conductivity of Ionic Liquid–Solvent Mixtures

  • Montes-Campos, Hadrián
  • Kondrat, Svyatoslav
  • Rilo, Esther
  • Cabeza, Óscar
  • Varela, Luis M.
This document is the Accepted Manuscript version of a Published Work that appeared in final form in The Journal of Physical Chemistry C, copyright © 2020 American Chemical Society after peer review and technical editing by the publisher., [Abstract] Charge transport in ionic systems is of paramount importance in many areas, but the existing theories provide reliable description only at low electrolyte concentrations. A promising theory is the pseudo-lattice or cell theory of fluids, which describes an ionic solution as a mixture of solvent-rich and ion-rich cells, characterized by different ion mobilities, with ion transport taking place by means of a hopping mechanism. The conventional approach considers ion hops between statistically independent cells and leads to a quadratic dependence of the conductivity on ion concentration. Herein, we derive a new equation for the concentration-dependent conductivity by adopting the random-alloy approximation, which takes into account cell–cell correlations. The derived equation describes remarkably well the conductivities of ionic liquid–solvent mixtures and inorganic electrolytes in the whole range of concentration and brings new insights into their temperature and size dependence., Financial support from the Spanish Ministry of Economy and Competitiveness is gratefully acknowledged (grant numbers MAT2017-89239-C2-1-P and MAT 2017-89239-C2-2-P). This work received funding from Xunta de Galicia (AGRUP2015/11, ED431D 2017/06, ED431E 2018/08, and GRC ED431C 2016/001) and was partially supported by FEDER. H.M.-C. thanks the Spanish Ministry of Education for the FPU grant. We thank Galician Supercomputing Centre (CESGA) for providing computational facilities. Funding from the European Union COST Actions CM1206 and MP1303 is also acknowledged. S.K. and L.M.V. acknowledge CONIN project of the European Union’s Horizon 2020 Research and Innovation Programme (Marie Skłodowska-Curie grant agreement 409734276) and personally thank Alina Ciach (IPC, Warsaw) for the invitation to the CONIN Workshop in Warsaw where this work was initiated, Xunta de Galicia; AGRUP2015/11, Xunta de Galicia; ED431D 2017/06, Xunta de Galicia; ED431E 2018/08, Xunta de Galicia; ED431C 2016/001
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Influence of Small Quantities of Water on the Physical Properties of Alkylammonium Nitrate Ionic Liquids

  • Ausín, David
  • Parajó, Juan José
  • Trenzado, José L.
  • Varela, Luis M.
  • Cabeza, Óscar
  • Segade, Luisa
[Abstract] This paper presents a comprehensive study of two alkylammonium nitrate ionic liquids. As part of this family of materials, mainly ethylammonium nitrate (EAN) and also propylammonium nitrate (PAN) have attracted a great deal of attention during the last decades due to their potential applications in many fields. Although there have been numerous publications focused on the measurement of their physical properties, a great dispersion can be observed in the results obtained for the same magnitude. One of the critical points to be taken into account in their physical characterization is their water content. Thus, the main objective of this work was to determine the degree of influence of the presence of small quantities of water in EAN and PAN on the measurement of density, viscosity, electrical conductivity, refractive index and surface tension. For this purpose, the first three properties were determined in samples of EAN and PAN with water contents below 30,000 ppm in a wide range of temperatures, between 5 and 95 °C, while the last two were obtained at 25 °C. As a result of this study, it has been concluded that the presence of water is critical in those physical properties that involve mass or charge transport processes, resulting in the finding that the absolute value of the average percentage change in both viscosity and electrical conductivity is above 40%. Meanwhile, refractive index (≤0.3%), density (≤0.5%) and surface tension (≤2%) present much less significant changes., This research was funded by the Spanish MINISTRY OF ECONOMY AND COMPETITIVENESS, grant numbers MAT2017-89239-C2-1-P and MAT2017-89239-C2-2-P. D. Ausín thanks the funding support of Fundación Segundo Gil Dávila. J.J. Parajó thanks the funding support of I2C postdoctoral program of Xunta de Galicia
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Structural Characterization by NMR Procedure of C₄C₁Pyrr TFSI Doped with Lithium TFSI Salt in Liquid and Gel States

  • Vallet Moreno, Pablo
  • Parajó, Juan José
  • Fernández-Míguez, Lois
  • Sotuela, Félix
  • Morcillo, Ángel
  • Villanueva López, María
  • Cabeza, Óscar
  • Matveev, Vladimir V.
  • Ievlev, A.V.
  • Tutukin, Konstantin
  • Varela, Luis M.
  • Salgado, Josefa
[Abstract] Ionic liquids represent a viable option as electrolytes for electrochemical applications such as energy storage devices, due to their high ionic conductivity and wide electrochemical window. However, liquid electrolytes present important problems of safety and performance, and encapsulation in a solid matrix can be a good solution to improve it. In this work, changes in the structure of the mixtures of ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide and lithium bis(trifluoromethylsulfonyl)imide against the concentration of the salt (0, 0.1, and 1.5 molal), and the effect of nanoconfinement through gelation process were studied using NMR technique., This work was supported by the Spanish Ministry of Economy and Competitiveness and FEDER Program through the projects MAT2014-57943-C3-1-P, MAT2014-57943-C3-3-P, MAT2017-89239-C2-1-P as well as by Xunta de Galicia through GRC ED431C 2020/10 project and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06. P. Vallet and J. J. Parajó thank funding support of FPI Program from the Spanish Ministry of Science, Education and Universities and I2C postdoctoral Program of Xunta de Galicia, respectively, Xunta de Galicia; ED431C 2020/10, Xunta de Galicia; ED431D 2017/06
RUC. Repositorio da Universidade da Coruña
Publicación Artículo científico (JournalArticle)

Liquid Range of Ionic Liquid – Metal Salt Mixtures for Electrochemical Applications

  • Salgado, Josefa
  • Parajó, Juan José
  • Villanueva López, María
  • Rodríguez, Julio R.
  • Cabeza, Óscar
  • Varela, Luis M.
This is an accepted version of the published document., [Abstract] The effect of the nitrate salt addition on the liquid range of the protic ionic liquid ethylammonium nitrate (EAN) was studied in this work. The salts used were monovalent, LiNO3; divalent, Mg(NO3)2 and Ca(NO3)2, and trivalent, Al(NO3)3; inorganic salts containing metals relevant for electrochemical applications. Solid-liquid transitions, which define the lower limit of the liquid range of the fluids, were determined using differential scanning calorimetry (DSC), whereas the upper limit, which is given by degradation or boiling temperatures, was determined by means of thermogravimetric analysis (TGA). Our results show that salt addition induces melting-point depressions, but no significant boiling point elevations were detected. The so-called nanostructured solvation mechanism is used in order to rationalize the thermodynamics of the mixtures in terms of the occurrence of highly incompressible, low mobility solvation complexes [M(NO3)n]z+−n in the polar cavities of the IL giving rise to pseudo-lattice nanocrystals that are stable in the liquid phase., Authors acknowledge M. Gómez (RIAIDT-USC) for the technical support in DSC measurements. This work was supported by Spanish Ministry of Economy and Competitiveness and FEDER Program through the projects MAT2014-57943-C3-1-P, MAT2014-57943-C3-3-P, MAT2017-89239-C2-1-P and MAT2017-89239-C2-2-P as well as by Xunta de Galicia through GRC ED431C 2016/001 and ED431E 2018/08 projects and the Galician Network of Ionic Liquids (ReGaLIs) ED431D 2017/06, Xunta de Galicia; ED431C 2016/001, Xunta de Galicia; ED431E 2018/08, Xunta de Galicia; ED431D 2017/06
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Borophene vs. graphene interfaces: Tuning the electric double layer in ionic liquids

  • Gómez-González, Víctor
  • Otero-Mato, J. Manuel
  • Montes-Campos, Hadrián
  • García-Andrade, Xabier
  • García-Fuente, Amador
  • Vega, Andrés
  • Carrete, Jesús
  • Cabeza, Oscar
  • Gallego, Luis J.
  • Varela, Luis M.
In this work we perform molecular dynamics simulations of mixtures of a prototypical protic ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4]), with lithium tetrafluoroborate (LiBF4), confined between two borophene walls of three different surface charges, −1, 0 and +1 e/nm2, where e is the elementary charge. The properties of the system are analyzed by means of ionic density profiles, angular orientations of [BMIM]+ cations close to the wall and vibrational densities of states for the salt cations close to the walls. The lateral structure of the first layer close to the surface is also studied on one hand, calculating Minkowski parameters and the Shannon entropy of the patterns of the 2D density maps of the anions placed there and, on the other hand, computing the 2D-Fourier transform of the positions of these anions. Our results are compared with those obtained previously for the same mixtures confined between two graphene walls. Although similarities exist between both cases, interesting differences are observed in the lateral structure that the ionic liquid adopts near borophene interfaces due to their strong anisotropy. In particular, we have observed that borophene induces more markedly ordered 2D patterns in the innermost layer of the ionic liquid electric double layer, specially when they are charged. It is this feature that makes borophene a potential candidate for battery electrode applications with possibilities beyond those of graphene., The financial support of the Spanish Ministry of Economy and Competitiveness (Projects MAT2017-89239-C2-1-P, MAT2017-89239-C2-2-P, CTQ2015-65816-R and PGC2018-093745-B-I00) is gratefully acknowledged. Moreover, this work was funded by the Xunta de Galicia (ED431D 2017/06, ED431E 2018/08 and GRC ED431C 2016/001) and the Junta de Castilla y León (Project VA124G18). All these research projects were partially supported by FEDER. H. M-C. and J. M. O-M. thank the Spanish Ministry of Education for their FPU grant. Facilities provided by the Galician Supercomputing Centre (CESGA) are also acknowledged, as well as funding from the European Union (COST Actions CM1206 and MP1303)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ionic liquids nanoconfined in zeolite-templated carbon: A computational study

  • Montes-Campos, Hadrián
  • Méndez-Morales, T.
  • Otero-Mato, J. Manuel
  • Cabeza, Oscar
  • Gallego, Luis J.
  • Lomba, Enrique
  • Varela, Luis M.
12 pags., 17 figs., 1 tab., Molecular dynamics simulations are reported for a protic (ethylammonium nitrate) and an aprotic (1-ethyl-3-methylimidazolium tetrafluoroborate) ionic liquid nanoconfined inside a faujasite-templated carbon. The structure and dynamics of ionic species inside nanotubes of relevant sizes are studied in order to understand the behavior of the dense ionic solvents in the zeolite-templated carbon. The structure (density, coordination numbers) of the confined fluid reflects a mixed dimensionality inside the zeolite-templated carbon, while the single-particle dynamics shows fundamental changes relative to that of ionic liquids confined in carbon nanotubes. Finally, no significant differences are found between the protic and the aprotic ionic liquids, which seems to suggest that the influence of hydrogen bonding is heavily suppressed inside the zeolite-templated carbon., The financial support of the Spanish Ministry of Economy and Competitiveness (Projects MAT2017-89239-C2-1-P and MAT2017-89239-C2-2-P) is gratefully acknowledged. Moreover, this work was fundedby the Xunta de Galicia (ED431D 2017/06, ED431E 2018/08 and GRCED431C 2016/001). All these research projects were partially supportedby FEDER. H.M.-C. and J.M.O.-M. thank the Spanish Ministry of Education for their FPU grant. T. M.-M. thanks the Spanish Ministry of Science,Innovation and Universities for her Juan de la Cierva grant (IJC2018-036774-I). E.L acknowledges the support from the Agencia Estatal deInvestigación and Fondo Europeo de Desarrollo Regional (FEDER) undergrant No. FIS2017-89361-C3-2-P. Facilities provided by the Galician Supercomputing Centre (CESGA) are also acknowledged.