Pasar al contenido principal

ENERGIA RENOVABLE A PRODUCTOS: PRUEBA DE CONCEPTO Y ANALISIS DE SOSTENIBILIDAD

PID2020-112845RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE CANTABRIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Use of Chitosan as Copper Binder in the Continuous Electrochemical Reduction of CO2 to Ethylene in Alkaline Medium

  • Marcos-Madrazo, Aitor
  • Casado-Coterillo, Clara
  • Iniesta, Jesus
  • Irabien, Ángel
  • Iniesta, Jesus|||/items/9131f62f-f4a8-44bf-83be-90c9270e5d9d
This work explores the potential of novel renewable materials in electrode fabrication for the electrochemical conversion of carbon dioxide (CO2) to ethylene in alkaline media. In this regard, the use of the renewable chitosan (CS) biopolymer as ion-exchange binder of the copper (Cu) electrocatalyst nanoparticles (NPs) is compared with commercial anion-exchange binders Sustainion and Fumion on the fabrication of gas diffusion electrodes (GDEs) for the electrochemical reduction of carbon dioxide (CO2R) in an alkaline medium. They were tested in membrane electrode assemblies (MEAs), where selectivity to ethylene (C2H4) increased when using the Cu:CS GDE compared to the Cu:Sustainion and Cu:Fumion GDEs, respectively, with a Faradaic efficiency (FE) of 93.7% at 10 mA cm−2 and a cell potential of −1.9 V, with a C2H4 production rate of 420 µmol m−2 s−1 for the Cu:CS GDE. Upon increasing current density to 90 mA cm−2, however, the production rate of the Cu:CS GDE rose to 509 µmol/m2s but the FE dropped to 69% due to increasing hydrogen evolution reaction (HER) competition. The control of mass transport limitations by tuning up the membrane overlayer properties in membrane coated electrodes (MCE) prepared by coating a CS-based membrane over the Cu:CS GDE enhanced its selectivity to C2H4 to a FE of 98% at 10 mA cm−2 with negligible competing HER. The concentration of carbon monoxide was below the experimental detection limit irrespective of the current density, with no CO2 crossover to the anodic compartment. This study suggests there may be potential in sustainable alernatives to fossil-based or perfluorinated materials in ion-exchange membrane and electrode fabrication, which constitute a step forward towards decarbonization in the circular economy perspective.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Continuous carbon dioxide electroreduction to formate coupled with the single-pass glycerol oxidation to high value-added products

  • Fernández-Caso, Kevin
  • Peña-Rodríguez, Ailen
  • Solla-Gullón, José
  • Montiel, Vicente
  • Díaz-Sainz, Guillermo
  • Alvarez-Guerra, Manuel
  • Irabien, Ángel
  • Montiel, Vicente|||/items/bd7466e3-f423-4916-87ab-1bc5372bde2f
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
CO2 electroreduction has been considered a promising alternative to simultaneously reduce CO2 emissions and produce value-added products. Among others, the production of formic acid/formate is particularly attractive. Although promising results have already been obtained in the literature, one of the recent approaches to improve the process deals with the use of an alternative reaction at the anode instead of the traditional oxygen evolution reaction (OER). In this context, this work reports, for the first time, the study of the CO2 electroreduction to formate coupled with the electrooxidation of glycerol to high-added value products where both half-reactions operate in a continuous mode with a single pass of the reactants through the electrochemical cell. Interestingly, at the cathode, similar results to those previously reported were obtained, reaching formate concentrations of about 18 g·L-1 at a 200 mA·cm-2. In addition, at the anode, promising dihydroxyacetone productions of 196 µmol·m-2·s-1 were simultaneously achieved in the output stream of the anodic compartment. These findings represent a significant step forward for the development and application of the technology.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Magnetically enhanced electrochemical conversion of CO2 to formate: Experimental studies

  • Abarca, Jose Antonio
  • Wu, Xian
  • González-Fernández, Cristina
  • Karampelas, Ioannis H.
  • Gutierrez-Carballo, Alejandro
  • Gauthier, Joseph A.
  • Botte, Gerardine G.
  • Solla-Gullón, José
  • Díaz-Sainz, Guillermo
  • Irabien, Ángel
  • Gomez-Pastora, Jenifer
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
The application of external magnetic fields in electrochemical processes has emerged as a promising strategy to enhance efficiency. Nevertheless, the use of magnetic fields in electrochemical CO2 reduction (ERCO2) has been scarcely explored. This study evaluates the impact of magnetic fields on ERCO2 to formate in a filter-press reactor, combining experimental analysis with magnetic field modeling to understand the performance enhancements achieved by placing magnets outside the electrochemical cell. Magnetic field modeling reveals that the positioning of magnets relative to the cathode surface significantly affects the field strength. For instance, placing a magnet near the anode generates a field strength of 20 mT on the GDE, while positioning two magnets at opposite ends of the cell increases the field to 400 mT. Experimentally, placing magnets near the cathode or at both ends of the cell boosts formate concentration by more than 20 %, achieving values of 4.4 g L−1 and 4.95 g L−1, respectively, with FEs approaching 100 %. These improvements are attributed to the magnetohydrodynamic (MHD) effect, which enhances mass transfer by inducing turbulence in the cathodic electrolyte. This effect is particularly important at low catholyte flow rates, leading to a more than 50 % increase in formate concentration, reaching up to 27.25 g L−1 at a flow rate of 0.07 mL min−1 cm−2. However, the application of magnetic fields also increases energy consumption due to the higher cell voltage requirements, as indicated by Tafel analysis. Despite this limitation, this study demonstrates the potential application of magnetic fields to enhance ERCO2 processes, paving the way for future research to further explore and optimize this promising strategy.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Coupling glycerol oxidation reaction using Ni-Co foam anodes to CO2 electroreduction in gas-phase for continuous co-valorization

  • Fernández-Caso, Kevin
  • Molera, Martí
  • Andreu, Teresa
  • Solla-Gullón, José
  • Montiel, Vicente
  • Díaz-Sainz, Guillermo
  • Alvarez-Guerra, Manuel
  • Irabien, Ángel
  • Montiel, Vicente|||/items/bd7466e3-f423-4916-87ab-1bc5372bde2f
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
Electrocatalytic reduction of CO2 is a promising alternative for storing energy and producing valuable products, such as formic acid/formate. Continuous gas-phase CO2 electroreduction has shown great potential in producing high concentrations of formic acid or formate at the cathode while allowing the oxygen evolution or the hydrogen oxidation reactions to occur at the anode. It is advantageous to use a more relevant oxidation reaction, such as glycerol which is a plentiful by-product of current biodiesel production process. This work successfully manages to couple the glycerol oxidation reaction with continuous gas-phase CO2 electroreduction to formate with the implementation of Ni-Co foam-based anodes. The MEA-electrolyzer developed can achieve significantly high formate concentrations of up to 359 g L-1 with high Faradaic efficiencies of up to 95%, while also producing dihydroxyacetone at a rate of 0.434 mmol m−2 s−1. In comparison with existing literature, this represents an excellent trade-off between relevant figures of merit and can remarkably contribute to a future implementation of this coupled electrochemical system approach at larger scales.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Electrodeposited BiVO4-based photoanodes for an energy-efficient photo-assisted CO2-to-formate conversion

  • Abarca, Jose Antonio
  • Molera, Martí
  • Merino-Garcia, Ivan
  • Díaz-Sainz, Guillermo
  • Irabien, Ángel
  • Solla-Gullón, José
  • Fàbrega, Cristian
  • Andreu, Teresa
  • Albo, Jonathan
  • Solla-Gullón, José|||/items/59027465-51a1-4647-8345-0b316b59de48
The development of efficient photoanodes that reduce external energy requirements for the electrochemical conversion of CO2 to formate is essential for the future implementation of this technology. In this work, we explore different photoanode structures based on electrodeposited BiVO4 onto transparent FTO substrates to achieve a more efficient PEC reduction of CO2. Among the tested structures, the photoanode incorporating a Bi2O3 underlayer, which enhances the BiVO4-FTO interface by reducing electron-hole recombination, exhibits the best PEC performance. Integrating this photoanode into a CO2 photoelectrolyzer with back visible light illumination achieves an impressive current density of −29 mA cm−2 at constant −1.8 V (vs. Ag/AgCl). Using a Bi/C GDE as the cathode, the system produces up to 56.2 g L−1 of formate with a Faradaic efficiency of 96 %. In terms of energy performance, illuminating the photoanode reduces energy consumption by nearly 40 %, bringing it down to 317 kWh kmol−1, with an energy efficiency of 38 %. The external bias can be further decreased by increasing the irradiation intensity to 2.5 suns using concentrated solar light, resulting in an additional 10 % reduction in energy consumption (290 kWh kmol−1), while maintaining high conversion efficiencies for CO2 to formate (over 95 % Faradaic efficiency). Besides, energy efficiency improves by 12 %, as the cathodic potential is reduced to −1.65 V (vs. Ag/AgCl). These results represent significant progress in reducing the external bias required for CO2 to formate conversion in PEC systems, marking a step toward the industrial application of CO2 conversion technology.