Pasar al contenido principal

PROCESADO DUAL DE VITRIMEROS: MATERIALES SOSTENIBLES

PID2020-115102RB-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT ROVIRA I VIRGILI

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Membranes for Cation Transport Based on Dendronized Poly(epichlorohydrin-co-ethylene oxide). Part 1: The Effect of Dendron Amount and Column Orientation on Copolymer Mobility

  • Zare, Alireza
  • De la Flor, Silvia
  • Montané, Xavier
  • Reina, José Antonio
  • Giamberini, Marta
  • B. Pascual-Jose|||0000-0001-7562-916X
  • Ribes-Greus, A.|||0000-0003-2460-8291
[EN] Dendronized polyethers give rise to columnar LC structures which can successfully act as cation transport materials. Therefore, we prepared two different materials, based on Poly(epichlorohydrin-co-ethylene oxide) (PECH-co-EO) grafted with methyl 3,4,5-tris[4-(n-dodecan-1-yloxy)benzyloxy] benzoate, containing 20% or 40% modified units, respectively. The obtained polymers were characterized by differential scanning calorimetry (DSC), X-ray diffraction and optical microscopy between crossed polars (POM) and compared to the unmodified PECH-co-EO. In order to reach efficient transport properties, homeotropically oriented membranes were prepared by a fine-tuned thermal annealing treatment and were subsequently investigated by dynamic mechanical thermal analysis (DMTA) and dielectric thermal analysis (DETA). We found that the presence of the dendrons induces a main chain partial crystallization of the polyether chain and coherently increases the polymer Tg. This effect is more evident in the oriented membranes. As for copolymer orientation upon annealing, the cooling rate and the annealing temperature were the most crucial factors. DMTA and DETA confirmed that grafting with the dendron strongly hinders copolymer motions, but did not show great differences between unoriented and oriented membranes, regardless of the amount of dendrons., This research was funded by Ministerio de Ciencia e Innovacion, grant number PID2020116322RB-C32, PID2020-116322RB-C31 and PID2020-115102RB-C21. This project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 713679 and from the Universitat Rovira i Virgili (URV).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dielectric Properties in Oriented and Unoriented Membranes Based on Poly(Epichlorohydrin-co-Ethylene Oxide) Copolymers: Part III

  • B. Pascual-Jose|||0000-0001-7562-916X
  • Ribes-Greus, A.|||0000-0003-2460-8291
  • Zare, Alireza
  • De la Flor, Silvia
  • Reina, José Antonio
  • Giamberini, M.
[EN] The dielectric spectra and conductivity properties of neat poly(epichlorohydrin-co-ethylene oxide)(PECH-co-EO) copolymer and two modified copolymers with a 20% or 40% of dendron 3,4,5-tris[4-(n-dodecan-1-yloxy)benzyloxy] benzoate units were analysed. A process of thermal orientation was applied to the copolymers to fine-tune the molecular motion of the side chains and determine their validity for cation transport materials. The study was conducted using Dielectric Thermal Analysis (DETA). The spectra of the modified unoriented and oriented copolymers consisted of five dielectric relaxations (delta, gamma, beta, alpha(Tg), and alpha(melting)). The analysis of the relaxations processes shows that as the grafting with the dendron units increases, both the lateral and main chains have a greater difficulty moving. The thermal orientation induces in the main chain partial crystallization, including the polyether segments, and modifies the cooperative motion of the main chain associated with the glass transition (alpha(Tg)). A deep analysis of the electrical loss modulus revealed that the degree of modification only modifies the temperature peak of each relaxation, and this effect is more perceived if the dendron unit content is higher (40%). The thermal orientation process seems equal to the spectra of CP20-O and CP40-O to the point that the degree of modification does not matter. Nevertheless, the fragility index denotes the differences in the molecular motion between both copolymers (40% and 20%) due to the thermal orientation. The study of the electric conductivity showed that the ideal long-range pathways were being altered by neither the thermal orientation process nor the addition of dendrimers. The analysis of the through-plane proton conductivity confirmed that the oriented copolymer with the highest concentration of dendrimers was the best performer and the most suitable copolymer for proton transport materials., This research was funded by Ministerio de Ciencia e Innovacion, grant number PID2020115102RB-C21, PID2020-116322RB-C31, PID2020-116322RB-C32. This project has received funding from the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No. 713679 and from the Universitat Rovira i Virgili(URV).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Dual-cured thermosets based on eugenol derivatives and thiol chemistry

  • Roig Gibert, Adriá
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • De la Flor López, Silvia
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
This paper aims to increase sustainability in thermosetting polymeric fields using bio-based monomers and environmentally friendly processing technologies based on dual-curing. Eugenol has been transformed into acrylate epoxy eugenol (AEEU) that can participate in thio-Michael additions and thiol-epoxy reactions. These reactions constitute the first and second steps of the sequential dual-curing process. A basic catalyst has been added to favor the kinetics of the curing process. We have selected three thiols with functionalities 3, 4, and 6, the first is derived from eugenol, and the others are derived from pentaerythritol, all can be obtained from renewable resources. To tailor and improve the intermediate material characteristics in the dual-curing process, we have added the triacrylate of glycerol. By changing its proportion, a liquid or a rubbery solid can be obtained as an intermediate, which allows a significant number of application technologies. Rheology, DSC, and FTIR were used to follow the evolution of both curing steps and to confirm the sequential character of the dual-curing. The thermal characteristics of intermediate and final materials have been evaluated by TGA and DMTA. Tensile tests at break were performed to evaluate the mechanical properties., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/10.13039/501100011033 and European Union “NextGenerationEU”/PRTR. We acknowledge these grants, and we also thank the Generalitat de Catalunya (2021-SGR00154). Bruno Bock Thiochemicals is acknowledge for kindly giving us thiol monomers.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Eugenol-based dual-cured materials with multiple dynamic exchangeable bonds

  • Roig Gibert, Adriá
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • De la Flor López, Silvia
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
In the present work, the preparation of sustainable thermosets has been approached simultaneously from three different points of view: a) the use of bio-based monomers chemically modified through green methodologies, b) the adoption of dual curing through click-type reactions to implement more efficient manufacturing processes, and c) inclusion of interchangeable groups in the network, to enable the reuse and recycling of the material at the end of its useful life and avoid waste generation. The first goal has been approached by synthesizing in a greener way an acrylate-epoxy derivative of eugenol (AEEU) and a glycerol triacrylate (GTA), both biobased resources. Then, the second approach was addressed by using biobased cystamine as a crosslinker to obtain materials through a dual-curing procedure based on a first “click” aza-Michael reaction and a second “click” epoxy-amine reaction. Intermediate and final materials could be prepared with different tailorable properties by controlling the molar ratio of the AEEU and GTA. By using DSC and rheology, we could evaluate the sequentiality and the gelation of the curing process. Finally, the covalent adaptable networks (CANs) prepared contained three different types of dynamic bonds (disulfide, esters, and ß-aminoesters) and their thermomechanical properties were tested by DMA revealing Tgs above room temperature from 47 to 70 °C. Bending tests at break were performed to evaluate the mechanical properties reaching values up to 90 MPa of stress at break and 7 % of deformation. Stress relaxation tests showed that all materials could relax the stress at relatively low temperatures (120 °C) in less than 21 min. The associative and dissociative behavior of these materials was investigated through rheology revealing a clear drop of the modulus at high temperatures and frequencies when cystamine was used as a crosslinker. Moreover, their reprocessability was tested obtaining homogeneous samples with no significant changes in their chemical and thermal properties highlighting the great potential and wide range of possibilities in many different fields of these CANs., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/10.13039/ 501100011033 and European Union “NextGenerationEU”/PRTR. We acknowledge these grants and we also thank to the Generalitat de Cat- alunya (2021-SGR-00154).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Tunable dual-curing acrylic/epoxy systems for 3D printing with enhanced joint performance via carbon nanotubes

  • Escribá Flores, Armando Alfredo
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ferrando Piera, Francesc|||0000-0003-4450-2734
  • Fabregat Sanjuan, Albert|||0000-0002-2878-1369
This study presents a novel dual-curing strategy for low-viscosity, high-performance acrylic/epoxy systems, which enables precise control over the final density of the co-network structure and its thermo-mechanical properties. Unlike conventional acrylate/epoxy dual-curing systems, this new strategy incorporates a long chain extender (polyethylene glycol) covalently bonded within the epoxy network to specifically reduce the crosslinking density achieved in the second curing stage. This allows for fine-tuning of the material's mechanical properties, facilitating adjustments to the elastic modulus from 3 MPa to 2500 MPa and achieving maximum tensile strength values of 80 MPa, while maintaining a low viscosity of less than 35 mPa s, making it ideal for 3D printing vat photopolymerization applications. Additionally, the material exhibits good thermal stability and excellent printed components resolution, thereby opening a wide range of design options for achieving optimal configurations related to mechanical preferences and precise geometric accuracy. The work further includes an analysis of tensile strength in bonded joints, which is a crucial parameter in structural design, particularly for the fabrication of large parts through bonding. Moreover, the project proposes the incorporation of functionalized multi-walled carbon nanotubes (MWCNT-COOH) to enhance interfacial adhesion between phases., This work was funded by the Spanish Ministry of Science and Inno vation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21, PID2020-115102RB-C22 and PID2023- 147128OB-C21, and also by Generalitat de Catalunya (2021-SGR- 154). Armando Escribá acknowledges to the Martí Franqués fellowship program (2021PMF-BS-08). X. Fernández-Francos acknowledges the Serra-Húnter programme (Generalitat de Catalunya)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Biobased imine vitrimers obtained by photo and thermal curing procedures-promising materials for 3D printing

  • Vilanova Pérez, Anna
  • De la Flor López, Silvia
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
  • Roig Gibert, Adriá
Imine-based vitrimers were prepared from synthesized diimine-dimethacrylate monomer derived from biobased vanillin. First, a methacrylate derivative starting from vanillin was synthesized. The diimine derivative was synthesized by condensation of the aldehyde groups from two vanillin methacrylate units with the amine groups of hexamethylenediamine (HMDA). The synthesized product was used in formulations containing ethylene glycol phenyl ether methacrylate (EGPMA) as a reactive diluent for the customization of final material properties and cured by exposure to ultraviolet (UV)-light using suitable radical photoinitiators or else with temperature using a radical thermal initiator. Materials with glass transition temperatures (Tgs) ranging from 70 to 90 °C were prepared, showing good thermal stability and mechanical and thermomechanical properties. The evaluation of their vitrimeric characteristics revealed that all materials achieved a stress-relaxation factor (s = 0.37s0) in less than 130 s at 160 °C, with photocured materials exhibiting faster relaxation rates. The catalytic effect of phosphine oxide groups in imine metathesis has also been evidenced. All prepared materials could be mechanically recycled and completely solubilized in a two-step degradation process, putting evidence of their potential use for carbon fiber-reinforced composites (CFRCs). In addition, they demonstrated promising self-repairing abilities. Finally, as a proof of concept, it was established that these formulations could be effectively processed using a Digital Light Processing three-dimensional (3D) Printer (DLP), resulting in the fabrication of complex shapes with high resolution., This work is part of the R&D projects PID2020-115102RB- C21, PID2020-115102RB-C22, and TED2021-131102B−C22 funded by MCNI/AEI/10.13039/501100011033 and Euro- pean Union “NextGenerationEU”/PRTR. The authors ac- knowledge these grants and also thank the Generalitat de Catalunya (2021-SGR-00154).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Preparation of poly(thiourethane) networks by using a novel acidic organocatalyst. Evaluation of their vitrimer-like behavior

  • Guerrero Ruiz, Federico
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Flor López, Sílvia de la|||0000-0002-6851-1371
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
In this work, a novel acidic catalyst, isopropyl methane sulfonate, has been tested for the preparation of a series of poly(thiourethane) thermosets (PTU)s. The advantage of this compound is that in addition to being free of metals, by heating at temperatures above 100 °C, it releases methane sulfonic acid, which is the true catalyst allowing to maintain the formulation liquid at room temperature for a longer time than when using the more common dibutyltin dilaurate (DBTDL) catalyst. The materials obtained were characterized by thermogravimetry and thermomechanical analysis, which allow determining higher initial degradation temperatures than using tetraphenyl borate amidinium salts as basic organic catalysts. The PTUs prepared with this catalyst show good vitrimeric-like characteristics, with faster relaxation on increasing the amount of catalyst. The materials could be recycled without losing their chemical structure and mechanical performance., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/ 10.13039/ 501100011033. We acknowledge these grants and to the Generalitat de Catalunya (2017-SGR-77 and BASE3D). F.G. thanks to MCNI/AEI for the grant PRE2018-084192.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

The use of lanthanide triflates in the preparation of poly(thiourethane) covalent adaptable networks

  • Guerrero Ruiz, Federico
  • Gamardella, Francesco
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • De la Flor López, Silvia
  • Serra Albet, Maria Àngels|||0000-0003-1387-0358
Covalent adaptable networks (CANs) are new polymeric materials with the mechanical properties of thermosets and the possibility of being recycled like thermoplastics. Poly(thiourethane) networks have demonstrated vitrimeric-like behavior at high temperatures due to the trans-thiocarbamoylation process, which Lewis acids and bases can accelerate. In this study, we report the use of lanthanide triflates (La, Sm, Dy, Er, and Yb) as Lewis acid catalysts, a greener alternative to other metallic catalysts as dibutyltin dilaurate (DBTDL) widely used in poly (urethane) and poly(thiourethane) networks. Moreover, they are not as reactive as DBTDL, and the curing mixture can be manipulated for a longer time at room temperature. As monomers, trimethylolpropane tris(3- mercapto propionate) (S3), hexamethylene diisocyanate (HDI), and isophorone diisocyanate (IPDI) have been used. We have demonstrated that the materials prepared with lanthanum triflate present the lowest relaxation times than those prepared with other lanthanide triflates or DBTDL. Calorimetry (DSC) and infrared spectroscopy (FTIR) were applied to study the curing process. The materials obtained were fully characterized by thermog- ravimetric analysis (TGA) and thermomechanical tests (DMA)., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/10.13039/ 501100011033. We acknowledge these grants and to the Generalitat de Catalunya (2021-SGR-00154 and BASE3D). F.G. thanks to MCNI/AEI for the grant PRE2018-084192.
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Harnessing disulfide and transesterification bond exchange reactions for recyclable and reprocessable 3D-printed vitrimers

  • Vilanova Pérez, Anna
  • Moradi, Sasan|||0000-0002-3481-2889
  • Konuray, Ali Osman|||0000-0001-7281-006X
  • Ramis Juan, Xavier|||0000-0003-2550-7185
  • Roig Gibert, Adriá
  • Fernández Francos, Xavier|||0000-0002-3492-2922
Two new vitrimeric materials have been studied for potential additive manufacturing applications such as 3D- printing. A monomer containing disulfide bonds and ß-hydroxyesters was easily synthesized from two low- cost and commercially available reagents. Another disulfide-containing monomer was synthesized for compar- ison purposes. Materials were prepared through a UV-light radical polymerization of methacrylates. The addition of two reactive diluents such as poly(ethylene glycol) methyl ether methacrylate (PEGMA) and ethylene glycol phenyl ether methacrylate (EGPMA) was necessary to achieve a suitable viscosity for the curing as well as for their printability. The curing process was controlled by FTIR. Thermomechanical properties were investigated by means of DMTA analysis revealing near-ambient Tg values. Stress relaxation tests revealed that both materials were capable to relax the 63% of the initial stress in less than 10 min at 110 ¿C. The recyclability of the materials was achieved, and the mechanical and thermomechanical properties of the recycled samples were compared to the virgin ones revealing a great recovery of the initial properties. Finally, Digital Light Processing (DLP) technique was used to print complex structures with high resolution highlighting the great potential of these vitrimeric materials in 3D printing., This work was funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22, and also by Generalitat de Catalunya (2021-SGR-00154 and BASE3D). X. Fernández-Francos and O. Konuray acknowledge the Serra-Húnter programme (Generalitat de Catalunya)., Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Analysis of the non-ideal crosslinking process in thiol-X “click” thermosets

  • Belmonte Parra, Alberto|||0000-0002-0172-7557
  • De la Flor López, Silvia
  • Konuray, Ali Osman|||0000-0001-7281-006X
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ramis Juan, Xavier|||0000-0003-2550-7185
Thiol-click reactions are widely used in the preparation of thermosets. The network build-up process follows step-wise polymerization behavior, which is commonly analyzed assuming ideal step-wise behavior using well- known expressions such as the Flory-Stockmayer equation for the prediction of the gel point conversion. However, a number of factors contributing to departures from the expected ideal behavior can be identified: a) impurity of the reagents, b) complexity of the reaction mechanism and c) internal cyclization processes. In order to maximize the accuracy of predictions about the expected crosslinking behavior and therefore fine-tune the design of thermosets designed as dual-curing systems or covalent adaptable networks (CANs), it is necessary to take into consideration all these sources of non-ideality. In this work, we aim to describe the effects of such factors on the network build-up process of thiol-click thermosets, making use of the recursive methodology of Miller and Macosko. The contribution of each factor is analyzed separately and their overall combined effect is discussed in relation with real data reported in the literature and experimental results., This work was funded by the Spanish Ministry of Science and Inno- vation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22, and also by Generalitat de Catalunya (2021-SGR-154). X. Fernández-Francos and O. Konuray acknowledge the Serra-Húnter programme (Generalitat de Catalunya).
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Evaluation of the effect of coupling agent on the kinetic and mechanical properties of a 3D printable dual curing epoxy/acrylate system

  • Escribá Flores, Armando Alfredo
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Ferrando Piera, Francesc|||0000-0003-4450-2734
  • Fabregat Sanjuan, Albert|||0000-0002-2878-1369
In recent years, the use of vat photopolymerization in additive manufacturing technology has created a prominent potential in the world manufacturing industry due to its adaptability and quick production capabilities. However, a challenge faced by this technology is creating large-sized parts and ensuring the geometric versatility of processed parts. The physical and mechanical properties of existing materials limit their processing, affecting their final applications. Moreover, dual-curing systems allow new possibilities to 3D printing if shape geometry is changed after the first curing stage and fixed in the second curing stage. This study aims to address these challenges by developing a dual-curing system involving epoxy/acrylic resins. We assess the kinetic and mechanical behavior, focusing on variations in the network coupling agent. The initial curing stage of a low viscous formulation, achieved through processing on a DLP 3D printer (partially cured), produces a flexible material allowing deformations up to 160 %. The second curing stage, achieved through thermal treatment, transforms the material into a rigid system with an impressive maximum tensile strength close to 80 MPa. We compare the contribution of the bonding agent in partial and total cured states. Comprehensive mechanical tests have been performed, including tension and shear evaluations. Results have been favorably aligned with relevant literature. The dual-curing approach shows promise in expanding 3D printing vat photopolymerization applications, providing new design and manufacturing possibilities by enhancing material availability. Our findings emphasize the benefits of the dual-curing system, including low viscosity, shape manipulation during intermediate curing that allows complex geometries with fast procedures and without the need of supports and exceptional strength and durability achieved in the final curing phase. Results on mechanical characterization in joints show that dual curing resins could be attractive in applications where different parts must be joined and precise alignment and structural integrity are crucial. The main reason for that is the interaction with the bonding agent in each state of the dual curing., This work was funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22, and also by Generalitat de Catalunya (2021-SGR-154). Armando Escribá acknowledges the Martí Franquès Research Fellowship Programme (2021PMFBS- 08). X. Fernández-Francos acknowledges the Serra-Húnter programme (Generalitat de Catalunya)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Electro-responsive shape-memory composites obtained via dual-curing processing

  • Russo, Claudio
  • Ramirez Falo, José Luis
  • Fernández Francos, Xavier|||0000-0002-3492-2922
  • Flor López, Sílvia de la|||0000-0002-6851-1371
In this work, electro-responsive shape-memory actuators were developed by incorporating a conductive heater in a dual-curing thiol-acrylate-epoxy shape-memory polymer (SMP). A conductive heater, consisting of an electrically conductive silverink track printed on Kapton® substrate, was assembled to the SMP, taking advantage of the dual-curing processing. The shape-memory effect (SME) was activated by the heat dissipated by the Joule effect in the conductive track. Boron nitride agglomerates were dispersed in the thiol-acrylate-epoxy layers to increase thermal conductivity and achieve faster shape-recovery. A thermoelectric control unit was developed to control the shape recovery of the electro-responsive actuators and provide different activation strategies. The electrically activated SME was investigated and compared to a traditional SME based on an external heating source given by the dynamic mechanical analyzer (DMA) apparatus. Electro-responsive actuators were found extremely faster than the conventional SMPs based on external heating. The fastest recovery was obtained by the 15% boron nitride actuator, which recovered the 100% of the original shape in only 8 s. The thermoelectric controlling device provided an optimal control of the shape recovery speed based on the pulse width modulation of the heating current under the application of a low voltage (5 V)., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Biobased imine vitrimers obtained by photo and thermal curing procedures-promising materials for 3D printing

  • Vilanova Pérez, Anna
  • De la Flor López, Silvia
  • Fernández Francos, Xavier
  • Serra Albet, Maria Àngels
  • Roig Gibert, Adriá
Imine-based vitrimers were prepared from synthesized diimine-dimethacrylate monomer derived from biobased vanillin. First, a methacrylate derivative starting from vanillin was synthesized. The diimine derivative was synthesized by condensation of the aldehyde groups from two vanillin methacrylate units with the amine groups of hexamethylenediamine (HMDA). The synthesized product was used in formulations containing ethylene glycol phenyl ether methacrylate (EGPMA) as a reactive diluent for the customization of final material properties and cured by exposure to ultraviolet (UV)-light using suitable radical photoinitiators or else with temperature using a radical thermal initiator. Materials with glass transition temperatures (Tgs) ranging from 70 to 90 °C were prepared, showing good thermal stability and mechanical and thermomechanical properties. The evaluation of their vitrimeric characteristics revealed that all materials achieved a stress-relaxation factor (s = 0.37s0) in less than 130 s at 160 °C, with photocured materials exhibiting faster relaxation rates. The catalytic effect of phosphine oxide groups in imine metathesis has also been evidenced. All prepared materials could be mechanically recycled and completely solubilized in a two-step degradation process, putting evidence of their potential use for carbon fiber-reinforced composites (CFRCs). In addition, they demonstrated promising self-repairing abilities. Finally, as a proof of concept, it was established that these formulations could be effectively processed using a Digital Light Processing three-dimensional (3D) Printer (DLP), resulting in the fabrication of complex shapes with high resolution., This work is part of the R&D projects PID2020-115102RB- C21, PID2020-115102RB-C22, and TED2021-131102B−C22 funded by MCNI/AEI/10.13039/501100011033 and Euro- pean Union “NextGenerationEU”/PRTR. The authors ac- knowledge these grants and also thank the Generalitat de Catalunya (2021-SGR-00154)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Tunable dual-curing acrylic/epoxy systems for 3D printing with enhanced joint performance via carbon nanotubes

  • Escribá Flores, Armando Alfredo
  • Fernández Francos, Xavier
  • Ferrando Piera, Francesc
  • Fabregat Sanjuan, Albert
This study presents a novel dual-curing strategy for low-viscosity, high-performance acrylic/epoxy systems, which enables precise control over the final density of the co-network structure and its thermo-mechanical properties. Unlike conventional acrylate/epoxy dual-curing systems, this new strategy incorporates a long chain extender (polyethylene glycol) covalently bonded within the epoxy network to specifically reduce the crosslinking density achieved in the second curing stage. This allows for fine-tuning of the material's mechanical properties, facilitating adjustments to the elastic modulus from 3 MPa to 2500 MPa and achieving maximum tensile strength values of 80 MPa, while maintaining a low viscosity of less than 35 mPa s, making it ideal for 3D printing vat photopolymerization applications. Additionally, the material exhibits good thermal stability and excellent printed components resolution, thereby opening a wide range of design options for achieving optimal configurations related to mechanical preferences and precise geometric accuracy. The work further includes an analysis of tensile strength in bonded joints, which is a crucial parameter in structural design, particularly for the fabrication of large parts through bonding. Moreover, the project proposes the incorporation of functionalized multi-walled carbon nanotubes (MWCNT-COOH) to enhance interfacial adhesion between phases., This work was funded by the Spanish Ministry of Science and Inno vation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21, PID2020-115102RB-C22 and PID2023- 147128OB-C21, and also by Generalitat de Catalunya (2021-SGR- 154). Armando Escribá acknowledges to the Martí Franqués fellowship program (2021PMF-BS-08). X. Fernández-Francos acknowledges the Serra-Húnter programme (Generalitat de Catalunya)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Electro-responsive shape-memory composites obtained via dual-curing processing

  • Russo, Claudio
  • Ramirez Falo, José Luis
  • Fernández Francos, Xavier
  • Flor López, Sílvia de la
In this work, electro-responsive shape-memory actuators were developed by incorporating a conductive heater in a dual-curing thiol-acrylate-epoxy shape-memory polymer (SMP). A conductive heater, consisting of an electrically conductive silverink track printed on Kapton® substrate, was assembled to the SMP, taking advantage of the dual-curing processing. The shape-memory effect (SME) was activated by the heat dissipated by the Joule effect in the conductive track. Boron nitride agglomerates were dispersed in the thiol-acrylate-epoxy layers to increase thermal conductivity and achieve faster shape-recovery. A thermoelectric control unit was developed to control the shape recovery of the electro-responsive actuators and provide different activation strategies. The electrically activated SME was investigated and compared to a traditional SME based on an external heating source given by the dynamic mechanical analyzer (DMA) apparatus. Electro-responsive actuators were found extremely faster than the conventional SMPs based on external heating. The fastest recovery was obtained by the 15% boron nitride actuator, which recovered the 100% of the original shape in only 8 s. The thermoelectric controlling device provided an optimal control of the shape recovery speed based on the pulse width modulation of the heating current under the application of a low voltage (5 V)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Evaluation of the effect of coupling agent on the kinetic and mechanical properties of a 3D printable dual curing epoxy/acrylate system

  • Escribá Flores, Armando Alfredo
  • Fernández Francos, Xavier
  • Ferrando Piera, Francesc
  • Fabregat Sanjuan, Albert
In recent years, the use of vat photopolymerization in additive manufacturing technology has created a prominent potential in the world manufacturing industry due to its adaptability and quick production capabilities. However, a challenge faced by this technology is creating large-sized parts and ensuring the geometric versatility of processed parts. The physical and mechanical properties of existing materials limit their processing, affecting their final applications. Moreover, dual-curing systems allow new possibilities to 3D printing if shape geometry is changed after the first curing stage and fixed in the second curing stage. This study aims to address these challenges by developing a dual-curing system involving epoxy/acrylic resins. We assess the kinetic and mechanical behavior, focusing on variations in the network coupling agent. The initial curing stage of a low viscous formulation, achieved through processing on a DLP 3D printer (partially cured), produces a flexible material allowing deformations up to 160 %. The second curing stage, achieved through thermal treatment, transforms the material into a rigid system with an impressive maximum tensile strength close to 80 MPa. We compare the contribution of the bonding agent in partial and total cured states. Comprehensive mechanical tests have been performed, including tension and shear evaluations. Results have been favorably aligned with relevant literature. The dual-curing approach shows promise in expanding 3D printing vat photopolymerization applications, providing new design and manufacturing possibilities by enhancing material availability. Our findings emphasize the benefits of the dual-curing system, including low viscosity, shape manipulation during intermediate curing that allows complex geometries with fast procedures and without the need of supports and exceptional strength and durability achieved in the final curing phase. Results on mechanical characterization in joints show that dual curing resins could be attractive in applications where different parts must be joined and precise alignment and structural integrity are crucial. The main reason for that is the interaction with the bonding agent in each state of the dual curing., This work was funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22, and also by Generalitat de Catalunya (2021-SGR-154). Armando Escribá acknowledges the Martí Franquès Research Fellowship Programme (2021PMFBS- 08). X. Fernández-Francos acknowledges the Serra-Húnter programme (Generalitat de Catalunya)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

The use of lanthanide triflates in the preparation of poly(thiourethane) covalent adaptable networks

  • Guerrero Ruiz, Federico
  • Gamardella, Francesco
  • Ramis Juan, Xavier
  • De la Flor López, Silvia
  • Serra Albet, Maria Àngels
Covalent adaptable networks (CANs) are new polymeric materials with the mechanical properties of thermosets and the possibility of being recycled like thermoplastics. Poly(thiourethane) networks have demonstrated vitrimeric-like behavior at high temperatures due to the trans-thiocarbamoylation process, which Lewis acids and bases can accelerate. In this study, we report the use of lanthanide triflates (La, Sm, Dy, Er, and Yb) as Lewis acid catalysts, a greener alternative to other metallic catalysts as dibutyltin dilaurate (DBTDL) widely used in poly (urethane) and poly(thiourethane) networks. Moreover, they are not as reactive as DBTDL, and the curing mixture can be manipulated for a longer time at room temperature. As monomers, trimethylolpropane tris(3- mercapto propionate) (S3), hexamethylene diisocyanate (HDI), and isophorone diisocyanate (IPDI) have been used. We have demonstrated that the materials prepared with lanthanum triflate present the lowest relaxation times than those prepared with other lanthanide triflates or DBTDL. Calorimetry (DSC) and infrared spectroscopy (FTIR) were applied to study the curing process. The materials obtained were fully characterized by thermog- ravimetric analysis (TGA) and thermomechanical tests (DMA)., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/10.13039/ 501100011033. We acknowledge these grants and to the Generalitat de Catalunya (2021-SGR-00154 and BASE3D). F.G. thanks to MCNI/AEI for the grant PRE2018-084192., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Dual-cured thermosets based on eugenol derivatives and thiol chemistry

  • Roig Gibert, Adriá
  • Ramis Juan, Xavier
  • De la Flor López, Silvia
  • Serra Albet, Maria Àngels
This paper aims to increase sustainability in thermosetting polymeric fields using bio-based monomers and environmentally friendly processing technologies based on dual-curing. Eugenol has been transformed into acrylate epoxy eugenol (AEEU) that can participate in thio-Michael additions and thiol-epoxy reactions. These reactions constitute the first and second steps of the sequential dual-curing process. A basic catalyst has been added to favor the kinetics of the curing process. We have selected three thiols with functionalities 3, 4, and 6, the first is derived from eugenol, and the others are derived from pentaerythritol, all can be obtained from renewable resources. To tailor and improve the intermediate material characteristics in the dual-curing process, we have added the triacrylate of glycerol. By changing its proportion, a liquid or a rubbery solid can be obtained as an intermediate, which allows a significant number of application technologies. Rheology, DSC, and FTIR were used to follow the evolution of both curing steps and to confirm the sequential character of the dual-curing. The thermal characteristics of intermediate and final materials have been evaluated by TGA and DMTA. Tensile tests at break were performed to evaluate the mechanical properties., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/10.13039/501100011033 and European Union “NextGenerationEU”/PRTR. We acknowledge these grants, and we also thank the Generalitat de Catalunya (2021-SGR00154). Bruno Bock Thiochemicals is acknowledge for kindly giving us thiol monomers., Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Harnessing disulfide and transesterification bond exchange reactions for recyclable and reprocessable 3D-printed vitrimers

  • Vilanova Pérez, Anna
  • Moradi, Sasan
  • Konuray, Ali Osman
  • Ramis Juan, Xavier
  • Roig Gibert, Adriá
  • Fernández Francos, Xavier
Two new vitrimeric materials have been studied for potential additive manufacturing applications such as 3D- printing. A monomer containing disulfide bonds and ß-hydroxyesters was easily synthesized from two low- cost and commercially available reagents. Another disulfide-containing monomer was synthesized for compar- ison purposes. Materials were prepared through a UV-light radical polymerization of methacrylates. The addition of two reactive diluents such as poly(ethylene glycol) methyl ether methacrylate (PEGMA) and ethylene glycol phenyl ether methacrylate (EGPMA) was necessary to achieve a suitable viscosity for the curing as well as for their printability. The curing process was controlled by FTIR. Thermomechanical properties were investigated by means of DMTA analysis revealing near-ambient Tg values. Stress relaxation tests revealed that both materials were capable to relax the 63% of the initial stress in less than 10 min at 110 ¿C. The recyclability of the materials was achieved, and the mechanical and thermomechanical properties of the recycled samples were compared to the virgin ones revealing a great recovery of the initial properties. Finally, Digital Light Processing (DLP) technique was used to print complex structures with high resolution highlighting the great potential of these vitrimeric materials in 3D printing., This work was funded by the Spanish Ministry of Science and Innovation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22, and also by Generalitat de Catalunya (2021-SGR-00154 and BASE3D). X. Fernández-Francos and O. Konuray acknowledge the Serra-Húnter programme (Generalitat de Catalunya)., Objectius de Desenvolupament Sostenible::9 - Indústria, Innovació i Infraestructura, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Analysis of the non-ideal crosslinking process in thiol-X “click” thermosets

  • Belmonte Parra, Alberto
  • De la Flor López, Silvia
  • Konuray, Ali Osman
  • Fernández Francos, Xavier
  • Ramis Juan, Xavier
Thiol-click reactions are widely used in the preparation of thermosets. The network build-up process follows step-wise polymerization behavior, which is commonly analyzed assuming ideal step-wise behavior using well- known expressions such as the Flory-Stockmayer equation for the prediction of the gel point conversion. However, a number of factors contributing to departures from the expected ideal behavior can be identified: a) impurity of the reagents, b) complexity of the reaction mechanism and c) internal cyclization processes. In order to maximize the accuracy of predictions about the expected crosslinking behavior and therefore fine-tune the design of thermosets designed as dual-curing systems or covalent adaptable networks (CANs), it is necessary to take into consideration all these sources of non-ideality. In this work, we aim to describe the effects of such factors on the network build-up process of thiol-click thermosets, making use of the recursive methodology of Miller and Macosko. The contribution of each factor is analyzed separately and their overall combined effect is discussed in relation with real data reported in the literature and experimental results., This work was funded by the Spanish Ministry of Science and Inno- vation (MCIN/AEI/10.13039/501100011033) through R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22, and also by Generalitat de Catalunya (2021-SGR-154). X. Fernández-Francos and O. Konuray acknowledge the Serra-Húnter programme (Generalitat de Catalunya)., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Preparation of poly(thiourethane) networks by using a novel acidic organocatalyst. Evaluation of their vitrimer-like behavior

  • Guerrero Ruiz, Federico
  • Ramis Juan, Xavier
  • Flor López, Sílvia de la
  • Serra Albet, Maria Àngels
In this work, a novel acidic catalyst, isopropyl methane sulfonate, has been tested for the preparation of a series of poly(thiourethane) thermosets (PTU)s. The advantage of this compound is that in addition to being free of metals, by heating at temperatures above 100 °C, it releases methane sulfonic acid, which is the true catalyst allowing to maintain the formulation liquid at room temperature for a longer time than when using the more common dibutyltin dilaurate (DBTDL) catalyst. The materials obtained were characterized by thermogravimetry and thermomechanical analysis, which allow determining higher initial degradation temperatures than using tetraphenyl borate amidinium salts as basic organic catalysts. The PTUs prepared with this catalyst show good vitrimeric-like characteristics, with faster relaxation on increasing the amount of catalyst. The materials could be recycled without losing their chemical structure and mechanical performance., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/ 10.13039/ 501100011033. We acknowledge these grants and to the Generalitat de Catalunya (2017-SGR-77 and BASE3D). F.G. thanks to MCNI/AEI for the grant PRE2018-084192., Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Eugenol-based dual-cured materials with multiple dynamic exchangeable bonds

  • Roig Gibert, Adriá
  • Ramis Juan, Xavier
  • De la Flor López, Silvia
  • Serra Albet, Maria Àngels
In the present work, the preparation of sustainable thermosets has been approached simultaneously from three different points of view: a) the use of bio-based monomers chemically modified through green methodologies, b) the adoption of dual curing through click-type reactions to implement more efficient manufacturing processes, and c) inclusion of interchangeable groups in the network, to enable the reuse and recycling of the material at the end of its useful life and avoid waste generation. The first goal has been approached by synthesizing in a greener way an acrylate-epoxy derivative of eugenol (AEEU) and a glycerol triacrylate (GTA), both biobased resources. Then, the second approach was addressed by using biobased cystamine as a crosslinker to obtain materials through a dual-curing procedure based on a first “click” aza-Michael reaction and a second “click” epoxy-amine reaction. Intermediate and final materials could be prepared with different tailorable properties by controlling the molar ratio of the AEEU and GTA. By using DSC and rheology, we could evaluate the sequentiality and the gelation of the curing process. Finally, the covalent adaptable networks (CANs) prepared contained three different types of dynamic bonds (disulfide, esters, and ß-aminoesters) and their thermomechanical properties were tested by DMA revealing Tgs above room temperature from 47 to 70 °C. Bending tests at break were performed to evaluate the mechanical properties reaching values up to 90 MPa of stress at break and 7 % of deformation. Stress relaxation tests showed that all materials could relax the stress at relatively low temperatures (120 °C) in less than 21 min. The associative and dissociative behavior of these materials was investigated through rheology revealing a clear drop of the modulus at high temperatures and frequencies when cystamine was used as a crosslinker. Moreover, their reprocessability was tested obtaining homogeneous samples with no significant changes in their chemical and thermal properties highlighting the great potential and wide range of possibilities in many different fields of these CANs., This work is part of the R&D projects PID2020-115102RB-C21 and PID2020-115102RB-C22 funded by MCNI/AEI/10.13039/ 501100011033 and European Union “NextGenerationEU”/PRTR. We acknowledge these grants and we also thank to the Generalitat de Cat- alunya (2021-SGR-00154)., Postprint (published version)