Pasar al contenido principal

SINERGIAS DE FUNCIONALIZACION POR LASER E HIPERDOPADO PARA DISPOSITIVOS ESPECTRALMENTE SELECTIVOS-UCM

PID2023-148178OB-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2023
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD COMPLUTENSE DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Effect of soft annealing on optoelectronic performances of Ti-hyperdoped Si photodiodes

  • Benítez Fernández, Rafael
  • Rahman, K. M. A.
  • Godoy Pérez, Guillermo
  • Caudevilla Gutiérrez, Daniel
  • Studgeon, John W.
  • Pérez Zenteno, Francisco José
  • Duarte Cano, Sebastián
  • Algaidy, Sari
  • García Hernansanz, Rodrigo
  • Olea Ariza, Javier
  • Pastor Pastor, David
  • Prado Millán, Álvaro Del
  • San Andrés Serrano, Enrique
  • Sher, Meng-Ju
  • García Hemme, Eric
We investigate the impact of soft furnace annealing (250–450 °C) on the optoelectronic performance of Ti-hyperdoped Si photodiodes. The annealing step, introduced between Ti ion implantation and nanosecond pulsed laser melting (ns-PLM), was designed to improve the crystalline quality of the seed layer from which ns-PLM recrystallizes the implanted region. For Ti doses of 1 × 1015 and 2 × 1015 cm−2, soft annealing enhanced the minority carrier lifetime and reduced the diffusion saturation current, leading to improved external quantum efficiency (EQE) above the Si absorption edge (photon energies higher than 1.12 eV). At higher implantation doses, however, these improvements were less pronounced, suggesting a dose-dependent interplay between defect passivation and recrystallization dynamics. However, EQE in the sub-bandgap range slightly decreased after annealing for both dose levels, while high-dose samples consistently exhibited stronger photoresponse, indicating that process-induced defects may contribute beneficially to sub-bandgap absorption in Ti-hyperdoped Si. These findings highlight soft annealing as a practical means of tailoring carrier dynamics and optical response in Ti-hyperdoped Si. By balancing defect passivation and controlled defect retention, this approach opens new opportunities for optimizing Ti-hyperdoped Si photodiodes toward applications in broadband light detection, short-wave infrared sensing, and CMOS-compatible optoelectronics.
Docta Complutense
Publicación Artículo científico (JournalArticle)

Characterization of Cr implanted GaAs processed with ArF and Nd-YAG laser melting

  • Algaidy, Sari
  • Caudevilla Gutiérrez, Daniel
  • Benítez Fernández, Rafael
  • Duarte Cano, Sebastián
  • Pérez Zenteno, Francisco José
  • García Hernansanz, Rodrigo
  • San Andrés Serrano, Enrique
  • García Hemme, Eric
  • Olea Ariza, Javier
  • Siegel, Jan
  • Gonzalo, José
  • Pastor Pastor, David
  • Prado Millán, Álvaro Del
We present a detailed investigation on the properties of supersaturated GaAs using Cr implantation followed by nanosecond pulsed laser melting (PLM). A comparison between two different lasers was carried out (ArF and Nd:YAG). We have analyzed supersaturated samples by means of structural, electrical, optical, and optoelectronic techniques. Raman spectroscopy and Transmission electron microscopy results show a recovery of crystallinity after the PLM process. ToF-SIMS results reveal a Cr concentration above the solid solubility limit after the PLM process, featuring depth distribution depending on the type of laser used. The sheet resistance results obtained using van der Pauw configuration measurements show an activation of the implanted Cr in semi-insulating GaAs after PLM. Optical transmittance and Reflectance measurements show a sub-bandgap absorption (up to 10% for λ = 1250 nm) of the supersaturated GaAs:Cr related to the Cr incorporation, besides absorption induced by the PLM process itself. The origin of this sub-bandgap absorption has been analyzed by means of opto-electronic measurements revealing sub-bandgap photoresponsivity related to the absorption analyzed. The photoresponsivity measured below the bandgap originates from both the defects introduced by the PLM process and the states within the bandgap associated to the implanted Cr.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterization of Cr implanted GaAs processed with ArF and Nd-YAG laser melting

  • Algaidy, Sari
  • Caudevilla, Daniel
  • Benítez-Fernández, Rafael
  • Duarte-Cano, Sebastián
  • Pérez-Zenteno, Francisco
  • García-Hernansanz, Rodrigo
  • San Andres, Enrique
  • García-Hemme, Eric
  • Olea, Javier
  • Siegel, Jan
  • Gonzalo de los Reyes, J.
  • Pastor, David
  • Del Prado, Alvaro
14 pages, 9 figures, 2 tables . -- Special Issue on Ultra-doped Semiconductors for Electronic, Photonic and Spintronic Applications, We present a detailed investigation on the properties of supersaturated GaAs using Cr implantation followed by nanosecond pulsed laser melting (PLM). A comparison between two different lasers was carried out (ArF and Nd:YAG). We have analyzed supersaturated samples by means of structural, electrical, optical, and optoelectronic techniques. Raman spectroscopy and Transmission electron microscopy results show a recovery of crystallinity after the PLM process. ToF-SIMS results reveal a Cr concentration above the solid solubility limit after the PLM process, featuring depth distribution depending on the type of laser used. The sheet resistance results obtained using van der Pauw configuration measurements show an activation of the implanted Cr in semi-insulating GaAs after PLM. Optical transmittance and Reflectance measurements show a sub-bandgap absorption (up to 10% for λ = 1250 nm) of the supersaturated GaAs:Cr related to the Cr incorporation, besides absorption induced by the PLM process itself. The origin of this sub-bandgap absorption has been analyzed by means of opto-electronic measurements revealing sub-bandgap photoresponsivity related to the absorption analyzed. The photoresponsivity measured below the bandgap originates from both the defects introduced by the PLM process and the states within the bandgap associated to the implanted Cr., This work was partially supported by the Spanish Research Agency (AEI, Ministry of Research and Innovation) and the European Regional Development Fund (ERDF) under Grants PID2020-116508RB-I00, PID2023-149369OBC21 and PID2023-148178OB-C21/C22. The authors also acknowledge financial support via research grants HyperSolar (TED2021-130894B-C21) funded by the Recovery and Resilience Facility of the EU. The authors would also like to acknowledge financial support from the Ministry of Education in the Kingdom of Saudi Arabia. F Pérez-Zenteno is also thankful for predoctoral contract from UCM (call CT58/21CT59/21). R Benítez-Fernández acknowledges the predoctoral contract from Comunidad Autónoma de Madrid (PIPF2023/ECO-30541). The authors would like to acknowledge the support of the regional government of Madrid through the Project 4EVERPV-CM (TEC-2024/ECO-72)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-quality fs-laser structured Si in air for optoelectronic applications

  • Benítez-Fernández, Rafael
  • Gómez-Muñoz, Gonzalo
  • García-Hemme, Eric
  • Roca–Giménez, Núria
  • Cabello, Fátima
  • García-Pardo, Marina
  • Gonzalo de los Reyes, José
  • Solís Céspedes, Javier
  • Prado, Álvaro del
  • García-Lechuga, Mario
  • Olea, Javier
  • Siegel, Jan
  • Pastor, David
10 pages, 10 figures, In this work, we describe a methodology to highly improve the quality of micro-structured silicon obtained by femtosecond-laser irradiation in ambient air atmosphere. Optimum femtosecond laser irradiation conditions have been selected to obtain a high aspect ratio spike morphology at the surface of silicon. Due to the aggressive fs-laser process, the crystalline structure of the material presents extended defects, which can be removed by rapid thermal annealing. Moreover, thermal annealing triggers diffusion of oxygen to the surface, which was incorporated from the air atmosphere into the bulk upon repetitive fs-laser irradiation. This oxygen binds with silicon atoms within the amorphous surface layer, giving rise to SiOx, obtaining irregular decorations at the surface of the spike structures. These decorations can be removed by a buffered hydrofluoric acid solution, which etches the silicon oxide but not the crystalline silicon. Using this strategy we have obtained a high crystalline quality with: high absorption of around 95 % in the wavelength region from 200 to 1100 nm, minimized defect-related absorption from 1100 to 2500 nm; a crystalline lattice free of defects and oxygen; and a high aspect-ratio micro-spike morphology formed by c-Si free of surface SiO<inf>x</inf> nano-decorations that can be useful to fabricate optoelectronic devices., This work has been supported by grant HyperSolar (TED2021130894B-C21 and TED2021-130894B-C22) funded by MICIU/AEI/ 10.13039/501100011033 and by the European Union NextGenerationEU/PRTR, grant HyperSpec (PID2023-148178OB-C21 and PID2023‑148178OB-C22) funded by MICIU/AEI/10.13039/ 501100011033 and by ERDF/EU, grant MATRIX-CM ((TEC-2024/TEC- 85), funded by Consejería de Educacion, Ciencia y Universidades (Comunidad de Madrid, (Spain)). The support of the Regional Government of Madrid through the Project 4EVERPV-CM (TEC-2024/ECO-72) is acknowledged. This work was partially supported by the Spanish Research Agency (AEI, Ministry of Research and Innovation) and the European Regional Development Fund (ERDF) under grants PID2020- 116508RB-I00 and PID2020–117498RB-I00. R. Benítez-Fernandez acknowledges the predoctoral contract from Comunidad Autonoma de Madrid (PIPF-2023/ECO-30541). Authors want to acknowledge assistance from CAI de Tecnicas Químicas (Espectroscopía Raman y Correlacion) for the Raman measurements and CAI de Tecnicas Físicas (Implantaci on Ionica) from the Universidad Complutense de Madrid for the RTA processes. We also acknowledge ICTS-CNME (Madrid, Spain) for the SEM, TEM and STEM images, EDS and EDX characterization. Authors also acknowledge Servicio de Nanotecnología y Analisis de Superficies del CACTI de la Universidad de Vigo for ToF-SIMS measurements. Authors acknowledge the use of instrumentation as well as the technical advice provided by the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas” at University of Zaragoza, Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

High-quality fs-laser structured Si in air for optoelectronic applications

  • Benítez Fernández, Rafael
  • Gomez-Munoz, Gonzalo
  • García Hemme, Eric
  • Roca Giménez, Nuria
  • Cabello, Fátima
  • García Pardo, Marina
  • Gonzalo, Jose
  • Solis, Javier
  • Prado Millán, Álvaro Del
  • GarciaLechuga, Mario
  • Olea Ariza, Javier
  • Siegel, Jan
  • Pastor Pastor, David
In this work, we describe a methodology to highly improve the quality of micro-structured silicon obtained by femtosecond-laser irradiation in ambient air atmosphere. Optimum femtosecond laser irradiation conditions have been selected to obtain a high aspect ratio spike morphology at the surface of silicon. Due to the aggressive fs-laser process, the crystalline structure of the material presents extended defects, which can be removed by rapid thermal annealing. Moreover, thermal annealing triggers diffusion of oxygen to the surface, which was incorporated from the air atmosphere into the bulk upon repetitive fs-laser irradiation. This oxygen binds with silicon atoms within the amorphous surface layer, giving rise to SiOx, obtaining irregular decorations at the surface of the spike structures. These decorations can be removed by a buffered hydrofluoric acid solution, which etches the silicon oxide but not the crystalline silicon. Using this strategy we have obtained a high crystalline quality with: high absorption of around 95 % in the wavelength region from 200 to 1100 nm, minimized defect-related absorption from 1100 to 2500 nm; a crystalline lattice free of defects and oxygen; and a high aspect-ratio micro-spike morphology formed by c-Si free of surface SiOx nano-decorations that can be useful to fabricate optoelectronic devices.