Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Effect of soft annealing on optoelectronic performances of Ti-hyperdoped Si photodiodes

  • Benítez Fernández, Rafael
  • Rahman, K. M. A.
  • Godoy Pérez, Guillermo
  • Caudevilla Gutiérrez, Daniel
  • Studgeon, John W.
  • Pérez Zenteno, Francisco José
  • Duarte Cano, Sebastián
  • Algaidy, Sari
  • García Hernansanz, Rodrigo
  • Olea Ariza, Javier
  • Pastor Pastor, David
  • Prado Millán, Álvaro Del
  • San Andrés Serrano, Enrique
  • Sher, Meng-Ju
  • García Hemme, Eric
We investigate the impact of soft furnace annealing (250–450 °C) on the optoelectronic performance of Ti-hyperdoped Si photodiodes. The annealing step, introduced between Ti ion implantation and nanosecond pulsed laser melting (ns-PLM), was designed to improve the crystalline quality of the seed layer from which ns-PLM recrystallizes the implanted region. For Ti doses of 1 × 1015 and 2 × 1015 cm−2, soft annealing enhanced the minority carrier lifetime and reduced the diffusion saturation current, leading to improved external quantum efficiency (EQE) above the Si absorption edge (photon energies higher than 1.12 eV). At higher implantation doses, however, these improvements were less pronounced, suggesting a dose-dependent interplay between defect passivation and recrystallization dynamics. However, EQE in the sub-bandgap range slightly decreased after annealing for both dose levels, while high-dose samples consistently exhibited stronger photoresponse, indicating that process-induced defects may contribute beneficially to sub-bandgap absorption in Ti-hyperdoped Si. These findings highlight soft annealing as a practical means of tailoring carrier dynamics and optical response in Ti-hyperdoped Si. By balancing defect passivation and controlled defect retention, this approach opens new opportunities for optimizing Ti-hyperdoped Si photodiodes toward applications in broadband light detection, short-wave infrared sensing, and CMOS-compatible optoelectronics.
Docta Complutense
Publicación Contribución de congreso (ConferenceOutput)

Characterization of TiOx as electron selective contact using low-temperature oxidation process via high-pressure sputtering, Characterization of TiOx as electron selective contact using low-temperature oxidation process via high-pressure sputtering

  • Pérez Zenteno, Francisco José
  • Duarte Cano, Sebastián
  • Benítez Fernández, Rafael
  • Godoy Pérez, Guillermo
  • Torres, I.
  • Barrio, R.
  • Rebohle, L.
  • Caudevilla Gutiérrez, Daniel
  • Algaidy, Sari
  • García Hernansanz, Rodrigo
  • Olea Ariza, Javier
  • Pastor Pastor, David
  • Prado Millán, Álvaro Del
  • García Hemme, Eric
  • San Andrés Serrano, Enrique
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optoelectronic properties of GaP:Ti photovoltaic devices

  • Olea, J.
  • Gonzalo de los Reyes, J.
  • Siegel, Jan
  • Braña, A. F.
  • Godoy-Pérez, G.
  • Benítez-Fernández, R.
  • Caudevilla, D.
  • Algaidy, S.
  • Pérez-Zenteno, F.
  • Duarte-Cano, S.
  • Prado, A. del
  • García-Hemme, E.
  • García-Hernansanz, R.
  • Pastor, D.
  • San-Andrés, E.
  • Mártil, I.
6 pages, 6 figures, 1 table, Supersaturated GaP is of interest for the photovoltaic field since optical transitions at energies below the bandgap (2.26 eV) could enhance the overall device efficiency up to theoretically 60%. We have previously demonstrated that Ti supersaturated GaP can be obtained by means of ion implantation and pulsed-laser melting with high structural quality and measured its below-bandgap photoconductivity. In this work we report the first results of a GaP:Ti based photovoltaic device. We have fabricated and measured photovoltaic devices with a GaP:Ti absorber layer showing enhanced external quantum efficiency at wavelengths above 550 nm. Also, we have measured the absorption coefficient (around 104 cm−1) and refractive index of this absorber layer. Finally, current-voltage curves in darkness were measured and analyzed using a two-diodes model, showing improvable characteristics. Ideas to enhance the properties of the devices are suggested., Authors would like to acknowledge the “CAI de Tecnicas Físicas” of the Universidad Complutense de Madrid for the fabrication processes and “Laboratorio de Caracterizaci´ on de Superficies” of CENIM for XPS measurements. This work was partially supported by the Project MADRID-PV2 (P2018/EMT-4308) funded by the Regional Government of Madrid with the support from FEDER Funds, by the Spanish Research Agency (AEI, Ministry of Research and Innovation) and the European Regional Development Fund (ERDF) under grants TEC2017-84378-R, PID2020-116508RB-I00 and PID2020-117498RB-I00. The authors also acknowledge financial support via research grants HyperSolar (TED2021-130894B–C21/C22) funded by the Recovery and Resilience Facility of the EU and ALPHOMENA (PID2021-123190OB-I00) funded by the Spanish Research Agency (AEI, Ministry of Research and Innovation) and the European Regional Development Fund (ERDF). D. Caudevilla would also acknowledge the grant PRE2018-083798, financed by MICINN and European Social Fund. F. Perez-Zenteno is also thankful for financial collaboration from the Mexican grants program CONACyT and for predoctoral contract from UCM (call CT58/21-CT59/ 21). The authors would also like to acknowledge financial support from Ministry of Education in the Kingdom of Saudi Arabia. G. Godoy-Perez and R. Benítez-Fernandez acknowledges the research contracts under the Investigo Program (CT19/23-INVM-35 and CT19/23-INVM-27) of the Ministerio de Trabajo y Economía Social. A. F. Bra˜ na gratefully acknowledges the financial support from rom Grant No. TED2021- 129624B–C43 funded by the Spanish International Research Agency MCIN/AEI/10.13039/501100011033 and by “NextGenerationEU”/ PRTR., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tuning spike-like morphologies in Silicon by sustainable fs-laser processing in air for enhanced light absorption

  • Gómez-Munoz, Gonzalo
  • Benítez-Fernández, Rafael
  • Godoy-Perez, Guillermo
  • Cabello, Fatima
  • García-Pardo, Marina
  • Caudevilla, Daniel
  • Gonzalo de los Reyes, J.
  • Solís Céspedes, Javier
  • García-Lechuga, Mario
  • Olea, Javier
  • Pastor, David
  • Siegel, Jan
11 pages, 6 figures, 2 tables, In this work, we demonstrate that ultrafast laser processing (1030 nm, 290 fs) of silicon in ambient air strongly improves the material's performance in terms of absorption, both in the visible and near infrared spectral range, which paves the way for further studies on increasing the sub-bandgap absorption after texturing, suggesting the material developed as a sustainable substitute for black silicon processed in greenhouse gases atmospheres. Our approach is based on the fabrication of spike-like morphologies in ambient air and the subsequent annealing of the material by pulsed laser melting or rapid thermal annealing to recover its crystalline phase. In particular, the influence of three main processing parameters (fluence, pulse number and repetition rate) on the properties of the spike-like structures has been investigated, each of them revealing the possibility of a direct control on the size, shape and period of the spikes, and achieving a total tuning range of the period from 4 μm to 14 μm for a single laser wavelength. Macroscopic areas have been fabricated using short processing times, yielding absorption values A > 94% over the UV–VIS-NIR spectral range (250 nm - 1100 nm) without hyperdoping, and A ≥ 20% for longer wavelengths up to 2500 nm, while preserving the electrical performance of pristine silicon., This work has been supported by grant HyperSolar (TED2021-130894B-C21 and TED2021-130894B-C22) funded by MICIU/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”, grant ULS_PSB (PID2020-112770RB-C21) funded by MICIU/AEI/10.13039/501100011033, and grant HyperPHIR (PID2020-117498RB-I00) funded by the Spanish Research Agency (AEI, Ministry of Research and Innovation), the European Regional Development Fund (ERDF) and by the Spanish Ministry of Science and Innovation. G. Godoy-Pérez and R. Benítez-Fernández acknowledge the research contracts under the Investigo Program (CT19/23-INVM-35 and CT19/23-INVM-27) of the Ministerio de Trabajo y Economía Social. The authors would like to thank David Gomez at ICTP-CSIC for performing the 45° SEM measurements. Authors want to acknowledge assistance from CAI de Técnicas Químicas (Espectroscopía Raman y Correlación) and CAI de Técnicas Físicas (Implantación Iónica) from the Universidad Complutense de Madrid for Raman measurements and RTA. We also acknowledge ICTS-CNME (Madrid, Spain) for the SEM images and EDX characterization., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High-quality fs-laser structured Si in air for optoelectronic applications

  • Benítez-Fernández, Rafael
  • Gómez-Muñoz, Gonzalo
  • García-Hemme, Eric
  • Roca–Giménez, Núria
  • Cabello, Fátima
  • García-Pardo, Marina
  • Gonzalo de los Reyes, José
  • Solís Céspedes, Javier
  • Prado, Álvaro del
  • García-Lechuga, Mario
  • Olea, Javier
  • Siegel, Jan
  • Pastor, David
10 pages, 10 figures, In this work, we describe a methodology to highly improve the quality of micro-structured silicon obtained by femtosecond-laser irradiation in ambient air atmosphere. Optimum femtosecond laser irradiation conditions have been selected to obtain a high aspect ratio spike morphology at the surface of silicon. Due to the aggressive fs-laser process, the crystalline structure of the material presents extended defects, which can be removed by rapid thermal annealing. Moreover, thermal annealing triggers diffusion of oxygen to the surface, which was incorporated from the air atmosphere into the bulk upon repetitive fs-laser irradiation. This oxygen binds with silicon atoms within the amorphous surface layer, giving rise to SiOx, obtaining irregular decorations at the surface of the spike structures. These decorations can be removed by a buffered hydrofluoric acid solution, which etches the silicon oxide but not the crystalline silicon. Using this strategy we have obtained a high crystalline quality with: high absorption of around 95 % in the wavelength region from 200 to 1100 nm, minimized defect-related absorption from 1100 to 2500 nm; a crystalline lattice free of defects and oxygen; and a high aspect-ratio micro-spike morphology formed by c-Si free of surface SiO<inf>x</inf> nano-decorations that can be useful to fabricate optoelectronic devices., This work has been supported by grant HyperSolar (TED2021130894B-C21 and TED2021-130894B-C22) funded by MICIU/AEI/ 10.13039/501100011033 and by the European Union NextGenerationEU/PRTR, grant HyperSpec (PID2023-148178OB-C21 and PID2023‑148178OB-C22) funded by MICIU/AEI/10.13039/ 501100011033 and by ERDF/EU, grant MATRIX-CM ((TEC-2024/TEC- 85), funded by Consejería de Educacion, Ciencia y Universidades (Comunidad de Madrid, (Spain)). The support of the Regional Government of Madrid through the Project 4EVERPV-CM (TEC-2024/ECO-72) is acknowledged. This work was partially supported by the Spanish Research Agency (AEI, Ministry of Research and Innovation) and the European Regional Development Fund (ERDF) under grants PID2020- 116508RB-I00 and PID2020–117498RB-I00. R. Benítez-Fernandez acknowledges the predoctoral contract from Comunidad Autonoma de Madrid (PIPF-2023/ECO-30541). Authors want to acknowledge assistance from CAI de Tecnicas Químicas (Espectroscopía Raman y Correlacion) for the Raman measurements and CAI de Tecnicas Físicas (Implantaci on Ionica) from the Universidad Complutense de Madrid for the RTA processes. We also acknowledge ICTS-CNME (Madrid, Spain) for the SEM, TEM and STEM images, EDS and EDX characterization. Authors also acknowledge Servicio de Nanotecnología y Analisis de Superficies del CACTI de la Universidad de Vigo for ToF-SIMS measurements. Authors acknowledge the use of instrumentation as well as the technical advice provided by the National Facility ELECMI ICTS, node “Laboratorio de Microscopías Avanzadas” at University of Zaragoza, Peer reviewed
Docta Complutense
Publicación Artículo científico (JournalArticle)

High-quality fs-laser structured Si in air for optoelectronic applications

  • Benítez Fernández, Rafael
  • Gomez-Munoz, Gonzalo
  • García Hemme, Eric
  • Roca Giménez, Nuria
  • Cabello, Fátima
  • García Pardo, Marina
  • Gonzalo, Jose
  • Solis, Javier
  • Prado Millán, Álvaro Del
  • GarciaLechuga, Mario
  • Olea Ariza, Javier
  • Siegel, Jan
  • Pastor Pastor, David
In this work, we describe a methodology to highly improve the quality of micro-structured silicon obtained by femtosecond-laser irradiation in ambient air atmosphere. Optimum femtosecond laser irradiation conditions have been selected to obtain a high aspect ratio spike morphology at the surface of silicon. Due to the aggressive fs-laser process, the crystalline structure of the material presents extended defects, which can be removed by rapid thermal annealing. Moreover, thermal annealing triggers diffusion of oxygen to the surface, which was incorporated from the air atmosphere into the bulk upon repetitive fs-laser irradiation. This oxygen binds with silicon atoms within the amorphous surface layer, giving rise to SiOx, obtaining irregular decorations at the surface of the spike structures. These decorations can be removed by a buffered hydrofluoric acid solution, which etches the silicon oxide but not the crystalline silicon. Using this strategy we have obtained a high crystalline quality with: high absorption of around 95 % in the wavelength region from 200 to 1100 nm, minimized defect-related absorption from 1100 to 2500 nm; a crystalline lattice free of defects and oxygen; and a high aspect-ratio micro-spike morphology formed by c-Si free of surface SiOx nano-decorations that can be useful to fabricate optoelectronic devices.