Pasar al contenido principal

ESTABILIDAD HIDRAULICA Y TRANSMISION DE DIQUES ROMPEOLAS HOMOGENEOS DE BAJA COTA DISEÑADOS A ROTURA POR FONDO

PRE2019-089542

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprograma Subprograma Estatal de Formación
Convocatoria Contratos Predoctorales
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A new method to measure damage progression in Homogeneous Low-Crested Structures with a low-cost 3D depth-sensor

  • Muñoz-Palao, Sergio
  • Díaz-Carrasco, Pilar
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mechanical profilers are commonly used to measure damage to rubble mound breakwaters in small-scale physical tests. This study developed a non-intrusive methodology using low-cost 3D depth-sensors to measure damage progression in Homogeneous Low-Crested Structures (HLCS) with and without water in the wave flume. Although light refraction causes distortion in the presence of water, distorted scans are corrected with this new method using a Neural Network (NN) model. The new methodology is adequate to obtain undistorted profiles of emerged or submerged breakwaters and may be described in two steps: (1) a digital profiler algorithm, to describe the breakwater models in series of profiles in order to measure damage, and (2) a trained NN model, to correct the distortions caused by light refraction for the scans taken with water in the wave flume. The NN model to correct profiles requires two sets of scans, one in empty conditions and the other in submerged conditions; the two scans (dry-wet) can be easily obtained without disturbing the usual test programs. This is done by taking the scans at the beginning (dry and wet) and at the end (wet and dry) of each test series. By comparing profiles, the breakwater damage can be analysed after obtaining the series of undistorted profiles from the trained NN model and the distorted scans. To validate the method, a series of small-scale physical tests with Cubipod HLCS were carried out from no damage to severe damage, and then the estimations given by the trained NN models were compared with blind observations, taken from additional pairs of dry and wet scans. The good agreement between the observations and the estimations (R-2 > 0.985, r > 0.993) showed that low-cost 3D depth-sensors may be used as non-intrusive methods for breakwater profiling, even when scanning is done with water in the wave flume or basin., The first author is grateful for the financial support of MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe" under grant PRE2019-089542. This study was supported by two projects: (1) REMOBE (PID2021-126475OB-I00) and (2) HOLOBRACE (PID2021-128035OA-I00) funded by MCIN/AEI/10.13039/501100011033 and, as appropriate, by "ERDF A way of making Europe", by the "European Union NextGenerationEU/PRTR". The manuscript was revised by Debra Westall (Universitat Politecnica de Valencia, Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical construction tests to assess the feasibility of placement grids for Cubipod Homogeneous Low-Crested Structures

  • Muñoz-Palao, Sergio
  • Díaz-Carrasco, Pilar
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Placement grid design is a key phase when constructing armor layers in mound breakwaters. Homogeneous Low-Crested Structures (HLCS) are low-crested structures designed as artificial reefs for marine colonization, coral reef regeneration and beach protection. The placement grid affects the construction feasibility, hydraulic stability and wave transmission of HLCS. This study presents a numerical methodology to simulate a realistic placement procedure for armor units during the construction of HLCS. This numerical simulator is based on the open-source physics engine Bullet Physics Engine (BPE), which applies Newton's laws of motion to rigid bodies. From an initial theorical placement grid for Cubipod HLCS, a series of numerical realistic unit placement tests are carried out to emulate the placement process at prototype scale; placement velocity and spatial deviation of crawler cranes are given parameters associated with each specific project. Considering the placement velocity and spatial deviation during construction, the quality of each specific placement grid is associated with the measured placement errors and the corresponding initial construction deviation to HLCS. This numerical methodology is valuable to understand the influence and the uncertaintly of the construction procedure of armor layers in mound breakwaters., This study was funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe under grants HOLOBREAK (RTI2018-101073-B-I00), REMOBE (PID2021-126475OB-I00) and HOLOBRACE (PID2021-128035OA-I00). The first author is grateful for the financial support of MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe under grant PRE2019-089542. The second author is funded through the Juan de la Cierva 2020 program (FJC2020-044778- I) by Union Europea NextGenerationEU en el marco del Plan de Recuperacion, Transformacion y Resiliencia de Espana , Spanish Ministry of Science and Innovation. The manuscript was revised by Debra Westall (Universitat Politecnica de Valencia, Spain).
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Numerical construction tests to assess the feasibility of placement grids for Cubipod Homogeneous Low-Crested Structures

  • Muñoz-Palao, Sergio
  • Diaz-Carrasco, Pilar
  • Molines, Jorge
  • Gómez-Martín, M. Esther
  • Medina, Josep R.
Placement grid design is a key phase when constructing armor layers in mound breakwaters. Homogeneous Low-Crested Structures (HLCS) are low-crested structures designed as artificial reefs for marine colonization, coral reef regeneration and beach protection. The placement grid affects the construction feasibility, hydraulic stability and wave transmission of HLCS. This study presents a numerical methodology to simulate a realistic placement procedure for armor units during the construction of HLCS. This numerical simulator is based on the open-source physics engine Bullet Physics Engine (BPE), which applies Newton's laws of motion to rigid bodies. From an initial theorical placement grid for Cubipod HLCS, a series of numerical realistic unit placement tests are carried out to emulate the placement process at prototype scale; placement velocity and spatial deviation of crawler cranes are given parameters associated with each specific project. Considering the placement velocity and spatial deviation during construction, the quality of each specific placement grid is associated with the measured placement errors and the corresponding initial construction deviation to HLCS. This numerical methodology is valuable to understand the influence and the uncertaintly of the construction procedure of armor layers in mound breakwaters.