Pasar al contenido principal

ESTABILIDAD HIDRAULICA Y TRANSMISION DE DIQUES ROMPEOLAS HOMOGENEOS DE BAJA COTA DISEÑADOS A ROTURA POR FONDO

RTI2018-101073-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Contribución de congreso (ConferenceOutput)

Crown Wall Stability of Cube and Cubipod Armored Mound Breakwaters

  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mound breakwaters usually have a concrete crown wall to reduce the amount of quarry material and to improve accessibility. Popular methods to design crown walls consider the same value of the horizontal pressure in the lower edge of the vertical wall and the seaward edge of the crown wall base. Up-lift forces are calculated assuming a triangular pressure distribution with a value given by pressures in the vertical wall. This assumption is reasonable in structures where the foundation level is below the sea water level, but may significantly differ from reality in crown walls with foundation levels above the sea water level. This study focuses on the influence of the foundation level on the crown wall stability analyzing 2D physical tests of cube and Cubipod armored breakwaters with crown wall., The authors acknowledge the financial support of FEDER, Spanish Ministerio de Ciencia, Innovación y Universidades (Grant RTI2018-101073-B-100), SATO (Grupo OHL), Universitat Politècnica de València (Grant SP20180111, Primeros Proyectos de Investigación (PAID-06-18),Vicerrectorado de Investigación, Innovación y Transferencia de la Universitat Politècnica de València) and Generalitat Valenciana (Grant AEST/2019/004)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Estimation of layer coefficients of cubipod homogeneous low-crested structures using physical and numerical model placement tests

  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
  • Centi, Riccardo
  • Di Risio, Marcello
[EN] Homogeneous low-crested structures (HLCSs) on hard seabed are designed to protect beaches and regenerate coral reefs. The height of a HLCS depends on the placement grid which determines the crest freeboard, wave transmission and concrete consumption. In real seafloor conditions, it is not easy to define feasible placement grids for HLCSs on uneven sea bottoms. In this study, the parameters of the numerical model Bullet Physics Engine (BPE) are calibrated and validated using the results of small-scale physical model placement tests of fivelayer Cubipod HLCSs on horizontal rigid bottom. The BPE model showed a low sensitivity to variations in the calibrated parameters; the numerical model estimated the layer coefficients with global mean relative errors of 1.04% and 1.39% in the triangular and rectangular placements grids, respectively. Once the numerical model was calibrated, new numerical and physical model tests on a 4% rigid bottom slope were compared for validation. A five-layer Cubipod HLCS on a 4% bottom slope was simulated using the BPE numerical model showing a global mean relative error of 2.75% compared to the small-scale physical model tests. A good agreement was found between numerical and physical model tests of five-layer Cubipod HLCSs on both horizontal as well as 4% rigid bottom slope. The BPE numerical model was found a suitable tool to estimate the structure height of HLCSs and to optimize placement grids of HLCSs on real cases with hard sea bottom., The authors thank the two anonymous reviewers for their constructive comments and suggestions, the financial support of the Spanish Ministerio de Ciencia, Innovacion y Universidades (Grant RTI 2018-101073-B-I00) and also Karel De Keyser and Elias Jacobs for conducting the physical placement test.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical Study of Wave Forces on Crown Walls of Mound Breakwaters with Parapets

  • Molines, Jorge|||0000-0001-7850-0759
  • Bayón, Arnau|||0000-0001-5007-0208
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] The influence of parapets on crown walls of mound breakwaters on wave forces has not been extensively analyzed in the literature. In this study, numerical experiments were carried out using the open-source platform OpenFOAM(R) to evaluate the influence of nine crown wall geometries with and without parapets. The OpenFOAM(R) model was validated with laboratory experiments. Dimensionless horizontal forces and overturning moments due to horizontal forces increase when there is a parapet. Dimensionless up-lift forces provide similar results, regardless of the existence of a parapet. Crown walls with parapets increase the horizontal wave forces and overturning moments due to horizontal wave forces by a factor of two., This research was funded by (1) Universitat Politecnica de Valencia (Grant SP20180111, Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia) and (2) Spanish Ministerio de Ciencia, Innovacion y Universidades (Grant RTI2018-101073-B-I00).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Mild Bottom Slopes on the Overtopping Flow over Mound Breakwaters under Depth-Limited Breaking Wave Conditions

  • Mares-Nasarre, Patricia
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] The crest elevation of mound breakwaters is usually designed considering a tolerable mean wave overtopping discharge. However, pedestrian safety, characterized by the overtopping layer thickness (OLT) and the overtopping flow velocity (OFV), is becoming more relevant due to the reduction of the crest freeboards of coastal structures. Studies in the literature focusing on OLT and OFV do not consider the bottom slope effect, even if it has a remarkable impact on mound breakwater design under depth-limited breaking wave conditions. Therefore, this research focuses on the influence of the bottom slope on OLT and OFV exceeded by 2% of incoming waves, hc,2% and uc,2%. A total of 235 2D physical tests were conducted on conventional mound breakwaters with a single-layer Cubipod® and double-layer rock and cube armors with 2% and 4% bottom slopes. Neural networks were used to determine the optimum point to estimate wave characteristics for hc,2% and uc,2% calculation; that point was located at a distance from the model toe of three times the water depth at the toe (hs) of the structure. The influence of the bottom slope is studied using trained neural networks with fixed wave conditions in the wave generation zone; hc,2% slightly decreases and uc,2% increases as the gradient of the bottom slope increases., This research was funded by Ministerio de Economia y Competitividad and the Fondo Europeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R and RTI2018-101073-B-I00. The first author was also financially supported by the Ministerio de Educacion, Cultura y Deporte through the FPU program (Formacion de Profesorado Universitario) under grant FPU16/05081.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Analyzing sustainability awareness and professional ethics of civil engineering bachelor&apos, s degree students

  • Mares-Nasarre, Patricia
  • Martínez Ibáñez, Víctor|||0000-0003-4445-2896
  • Sanz-Benlloch, Amalia|||0000-0001-8051-0649
[EN] Teaching sustainability and ethics to engineering students is a challenging but necessary task that has been increasingly investigated during the last few years. In this research, a systematic method to identify the level of awareness in students about sustainability and ethics is developed. Here, it is applied to students studying the Civil Engineering bachelor¿s degree at the School of Civil Engineering of Universitat Politècnica de València (UPV), though this method is potentially applicable to equivalent ABET and EUR-ACE accredited bachelor¿s degrees. A survey was performed, and data was analyzed using Analytical hierarchical process technique; this technique determines the relative importance of each criterion, as well as the consistency of the emitted judgements, in an objective manner. These results allowed to discover that students do not have a robust opinion related to sustainability and ethics, except those students with previous experience in the construction sector. Environmental and social dimensions of sustainability and ethics were identified as the main focuses to emphasize in the civil engineering curriculum. Finally, actions to boot these principles are also proposed; potential courses where sustainability and ethics concepts could be explicitly included were selected and the inclusion of an environmental budget in the bachelor thesis was recommended, among others suggestions., The first author was financially supported by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe under grant RTI2018-101073-B-I00.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bunker consumption of containerships considering sailing speed and wind conditions

  • Medina, Josep R.|||0000-0001-5007-7426
  • Molines, Jorge|||0000-0001-7850-0759
  • Gonzalez-Escriva, J.A.|||0000-0003-2634-7961
  • Aguilar Herrando, José|||0000-0002-5518-1860
[EN] This study focuses on container vessel fuel consumption considering the wind conditions along the ship path in the liner route. Simple analytical and semi-empirical formulas are provided to estimate the total resistance force and the bunker consumption rate of fully loaded containerships between 5000 and 15000 TEU considering the effect of wind and the corresponding waves on the Beaufort scale. The bunker consumption rate is proportional to the total resistance force, so bad weather significantly increases fuel consumption. Examples of wind hindcasts and added resistance increases for the Atlantic Ocean, the Mediterranean Sea, and the Indian Ocean are provided for a better "a priori" estimation of the bunker consumption for a containership in a given route and time of the year, This work was supported by the Ministerio de Economia y Competitividad, Spain, and Fondo Europeo de Desarrollo Regional FEDER, EU [grant RTI2018-101073-B-I00].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Parapets on Wave Overtopping on Mound Breakwaters with Crown Walls

  • Molines, Jorge|||0000-0001-7850-0759
  • Bayón, Arnau|||0000-0001-5007-0208
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Background literature on the influence of parapets on the overtopping of mound breakwaters is limited. In this study, numerical tests were conducted using computational fluid dynamics (CFD) to analyze the influence of nine crown wall geometries (seven with parapets). The CFD model was implemented in OpenFOAM((R)) and successfully validated with laboratory tests. A new estimator of the dimensionless mean wave-overtopping discharges (logQ) on structures with parapets is proposed. The new estimator depends on the estimation of logQ of the same structure without a parapet. The effects on wave overtopping of the parapet angle (epsilon(p)), parapet width (w(p)), and parapet height (h(p)) were analyzed. Low values of epsilon(p) and w(p)/h(p) approximate to 1 produced the highest parapet effectiveness to reduce the mean wave-overtopping discharges., This research was funded by Universitat Politecnica de Valencia (Grant SP20180111, Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia). The authors are grateful for financial support from European FEDER and Spanish Ministerio de Economía y Competitividad (Grant RTI2018-101073-B-I00), SATO (OHL Group). The authors acknowledge the support provided by the postdoctoral company internship program AEST granted to Jorge Molines by Generalitat Valenciana (Grant AEST/2019/004) and by the postdoctoral program APOSTD granted to Arnau Bayon by Generalitat Valenciana (Grant APOSTD/2019/100).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

A new design formula to estimate wave transmission on cubipod homogeneous low-crested structures

  • Díaz-Carrasco, Pilar
  • Mares-Nasarre, Patricia
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] This study presents a new explicit empirical formula to estimate wave transmission on Cubipod Homogeneous Low-Crested Structures (HLCS) under depth-limited breaking wave conditions. The formula was derived using Artificial Neural Networks (ANN) to identify and quantify the influence of nineteen candidate explanatory variables on the squared wave transmission coefficient, K2T. A total of 210 two-dimensional physical model tests conducted at the Universitat Polite`cnica de Vale`ncia (Spain) were used to calibrate the formula. The dimensionless crest freeboard using the nominal diameter (Rc/Dn50) and the dimensionless incident wave height at the structure toe using the water depth (Hm0,I/hs) were identified as the most relevant explanatory variables. A new two-variable formulation with 3 fitting-parameters was found to estimate the proportion of transmitted energy, K2T, with a coefficient of determination R2 = 0.89. The proposed formula was also applied to an external dataset of experimental tests on Cubipod HLCS previously reported in the literature. The results demonstrated a significantly better agreement than existing empirical formulas confirming the robustness and applicability of the new formula. The proposed formula is a reliable and easy-to-apply new tool for the preliminary design of emerged and submerged undamaged HLCS in depth-limited breaking wave conditions. The new explicit formula is particularly suited for low-crested structures aimed at combining coastal protection and ecosystem enhancement, such as artificial reefs in coral environments., The authors acknowledge the support from grant RTI 2018-101073-B-I00 (HOLOBREAK) and PD 2021-128035OA-I00 (HOLOBRACE) funded by MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Explicit Neural Network-derived formula for overtopping flow on mound breakwaters in depth-limited breaking wave conditions

  • Mares-Nasarre, Patricia
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Sea level rise due to climate change, as well as social pressure to decrease the visual impact of coastal structures, have led to reduced crest freeboards, and this increases the overtopping hazard. In previous studies, pedestrian safety during overtopping events was assessed considering the overtopping layer thickness (OLT) and the overtopping flow velocity (OFV). This study analyzed the statistics of OLT and OFV on mound breakwaters without crown walls during severe wave storms. Small-scale 2D physical tests were conducted on mound breakwaters with dimensionless crest freeboards between 0.29 and 1.77, testing three armor layers (single-layer Cubipod (R), and double-layer cubes and rocks) in depth-limited breaking wave conditions and with two bottom slopes. Neural Networks were used to develop new estimators for the OLT and OFV exceeded by 2% of the incoming waves with a high coefficient of determination (0.866 < R-2 < 0.876). The best number of significant figures in the empirical coefficients of the new estimators was determined according to their variability. The 1 parameter Exponential and Rayleigh distribution functions were proposed to estimate the extreme values of OLT and OFV with 0.803 < R-2 < 0.812, respectively., The authors thank the three anonymous reviewers for their comments and suggestions. The authors acknowledge the financial support from the Spanish Ministerio de Economia y Competitividad and Fondo Europeo de Desarrollo Regional (FEDER) under grant RTI2018-101073-BI00. The first author was also financially supported through the FPU program (Formacion de Profesorado Universitario) funded by the Spanish Ministerio de Educacion, Cultura y Deporte under grant FPU16/05081. The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Overtopping flow on mound breakwaters under depth-limited breaking wave conditions

  • Mares Nasarre, Patricia
[ES] El cambio climático y la conciencia social sobre el impacto de las infraestructuras en el medio está llevando a la necesidad de diseñar diques en talud con cotas de coronación reducidas frente a eventos de rebase más extremos. Además, la mayoría de estos diques se construyen en zonas de profundidades reducidas, donde el oleaje rompe a causa de la limitación por fondo. Estudios recientes apuntan a la necesidad de considerar no sólo la caudal medio de rebase (q) sino también el máximo volumen individual de rebase (Vmax), el espesor de lámina de agua (OLT) y la velocidad del flujo de rebase (OFV) en el diseño de la cota de coronación de un dique en talud según criterios de rebase. No obstante, existen pocos estudios en la literatura científica centrados en Vmax en estructuras costeras sometidas a oleaje limitado por fondo. Además, estos estudios proporcionan resultados contradictorios en relación a la influencia de la limitación por fondo del oleaje sobre Vmax. En cuanto a OLT y OFV, no se han encontrado estudios en la literatura científica que permitan su predicción en diques en talud. En esta tesis doctoral, se han realizado ensayos físicos 2D en diques en talud rebasables (0.3≤Rc/Hm0≤2.5) sin espaldón y con tres mantos principales (Cubípodo®-1L, cubo-2L y escollera-2L) sobre dos pendientes de fondo suaves (m=2% and 4%) en condiciones de oleaje limitado por fondo (0.2≤Hm0/h≤0.9). Vmax junto con q son las variables más recomendadas en la literatura científica para diseñar la cota de coronación de diques en talud según criterios de rebase. En el presente estudio, los mejores resultados en la estimación de Vmax*=Vmax/(gHm0T012) se han obtenido empleando la función de distribución Weibull de dos parámetros con un coeficiente de determinación R2=0.833. Durante la fase de diseño de un dique en talud, es necesario predecir q para calcular Vmax cuando se emplean los métodos dados en la literatura científica. Por tanto, se debe estimar q con fines de diseño si no se dispone de observaciones directas. En caso de emplear la red neuronal CLASH NN para estimar q (R2=0.636), la bondad de ajuste de la función de distribución Weibull de dos parámetros propuesta en esta tesis para predecir Vmax* es R2=0.617. Así, el ratio entre Vmax* medido y estimado cae dentro del rango de 1/2 a 2 (banda de confianza del 90%) cuando se emplea q estimado con CLASH NN. Los nuevos estimadores desarrollados en la presente disertación proporcionan resultados satisfactorios en la predicción de Vmax* con un método más simple que aquellos propuestos en la literatura científica. No se ha encontrado una influencia significativa de la pendiente de fondo ni de la limitación por fondo del oleaje sobre Vmax* en este estudio. OLT y OFV están directamente relacionados con la estabilidad hidráulica de la coronación del dique y la seguridad peatonal frente a rebase. Por tanto, se requiere estimar OLT y OFV en la coronación del dique para diseñar apropiadamente su cota de coronación empleando criterios de rebase. En este estudio, se han empleado redes neuronales para desarrollar nuevos estimadores explícitos que permiten predecir OLT y OFV superados por el 2% del oleaje incidente con un alto coeficiente de determinación (0.866≤R2≤0.867). El número de cifras significativas apropiado para los coeficientes experimentales de dichos estimadores se ha determinado en base a su variabilidad. El punto óptimo en el que las características del oleaje deben ser estimadas para predecir OLT y OFV se ha identificado a una distancia de 3h desde el pie de la estructura (siendo h la profundidad a pie de dique). La pendiente de fondo tiene influencia sobre OLT y OFV. Los valores más extremos de OLT y OFV se han descrito empleando las distribuciones Exponencial de un parámetro y Rayleigh, respectivamente, con resultados satisfactorios (0.803≤R2≤0.812)., [CA] El canvi climàtic i la consciència social sobre l'impacte de les infraestructures al medi està portant a la necessitat de dissenyar dics en talús amb cotes de coronació reduïdes front a esdeveniments d'ultrapassament més extrems. A més, la majoria dels dics es construeixen en zones amb profunditats reduïdes on l'onatge es trenca a causa de la limitació per fons. Estudis recents apunten a la necessitat de considerar no solament el cabal mitjà de sobrepasse (q) sinó també el màxim volum individual de sobrepasse (Vmax), l'espessor de la làmina d'aigua (OLT) i la velocitat del flux de sobrepasse (OFV) pel disseny de la cota de coronació d'un dic en talús segons criteris de sobrepasse. No obstant, existeixen pocs estudis a la literatura científica centrats en Vmax en estructures costeres sotmeses a onatge limitat per fons. Addicionalment, aquests estudis proporcionen resultats contradictoris en relació a la influència de la limitació per fons de l'onatge sobre Vmax. Quant a OLT i OFV, no s'han trobat estudis a la literatura científica que permeten la seua predicció a dics en talús. En aquesta tesi doctoral, s'han realitzat assajos físics 2D amb dics en talús amb sobrepassos rellevants (0.3≤Rc/Hm0≤2.5) sense espatlló i amb tres elements al mantell principal (Cubípode-1L, cubs-2L i esculleres-2L) ubicats sobre pendents de fons suaus (m=2% i 4%) en condicions d'onatge limitat pel fons (0.2≤Hm0/h≤0.9). Vmax conjuntament amb q són les variables més recomanades a la literatura científica per dissenyar la cota de coronació en dics en talús segons criteris d'ultrapassament. Al present estudi, els millors resultats en l'estimació de Vmax*=Vmax/(gHm0T012) s'han obtingut utilitzant la funció de distribució Weibull de dos paràmetres amb un elevat coeficient de determinació R2=0.833. Durant la fase de disseny d'un dic en talús, és necessari predir q per calcular Vmax quan s'utilitzen els mètodes donats a la literatura científica. Per tant, es deu estimar q amb fins de disseny si no es disposa d'observacions directes. Si s'aplica la xarxa neuronal de CLASH NN per estimar q (R2=0.636), la bondat d'ajust de la funció de distribució Weibull de dos paràmetres proposada a aquesta tesi per predir Vmax* és R2=0.617. Així doncs, el ràtio entre el Vmax* mesurat i estimat es troba dins del rang de 1/2 a 2 (banda de confiança del 90%) quan s'usa q predit amb CLASH NN. Els nous estimadors desenvolupats a aquesta dissertació proporcionen resultats satisfactoris en la predicció de Vmax* amb un mètode més senzill que aquells proposats a la literatura científica. No s'ha trobat una influència significativa de la pendent de fons ni de la limitació de l'onatge per fons sobre Vmax* a aquest estudi. OLT i OFV estan directament relacionats amb l'estabilitat hidràulica de la coronació de dics i la seguretat de vianants front a ultrapassaments. Per tant, es requereix estimar OLT i OFV en la coronació de dics per dissenyar apropiadament la seua cota de coronació utilitzant criteris de sobrepasse. En aquest estudi, s'han usat xarxes neuronals per desenvolupar nous estimadors explícits que permeten predir OLT i OFV superats pel 2% de l'onatge incident amb un elevat coeficient de determinació (0.866≤R2≤0.867). El nombre de xifres significatives apropiat per als coeficients experimentals dels mencionats estimadors s'ha determinat basant-se en la seua variabilitat. El punt òptim on determinar les característiques de l'onatge deuen ser estimades per predir OLT i OFV s'ha identificat a una distància de 3h des del peu de l'estructura (on h és la profunditat a peu de dic). La pendent de fons té influència sobre OLT i OFV. Els valors més extrems de OLT i OFV s'han descrit amb les distribucions Exponencial d'un paràmetre i Rayleigh, respectivament, amb resultats satisfactoris (0.803≤R2≤0.812)., [EN] Climate change and the social concern about the impact of infrastructures is leading to mound breakwaters with reduced crest freeboards facing higher extreme overtopping events. In addition, most mound breakwaters are built in the surf zone where depth-limited wave breaking takes place. Recent studies point out the need of considering not only the mean wave overtopping discharge (q) but also the maximum individual wave overtopping volume (Vmax), the overtopping layer thickness (OLT) and the overtopping flow velocity (OFV) when designing mound breakwater crest elevation using overtopping criteria. However, few studies in the literature are focused on Vmax on coastal structures under depth-limited breaking wave conditions. In addition, those few studies report contradictory conclusions regarding the significance of depth-limited breaking waves on Vmax. With respect to OLT and OFV, no studies are found in the literature for their prediction on mound breakwaters. In this PhD thesis, 2D physical model tests were conducted on overtopped mound breakwaters (0.3≤Rc/Hm0≤2.5) without a crown wall armored with three armor layers (Cubipod®-1L, cube-2L and rock-2L) on two gentle bottom slopes (m=2% and 4%) in depth-limited breaking wave conditions (0.2≤Hm0/h≤0.9). Vmax together with q are the most recommended variables in the literature to design mound breakwater crest elevation based on overtopping criteria. In the present study, the 2-parameter Weibull distribution provides the best results when estimating Vmax*=Vmax/(gHm0T012) with coefficient of determination R2=0.833. During the design phase of a mound breakwater, q is needed to predict Vmax using methods given in the literature. Thus, q must be estimated for design purposes when direct observations are not available. If CLASH NN is used to estimate q (R2=0.636), the goodness-of-fit of the 2-parameter Weibull distribution proposed in this thesis to predict Vmax* is R2=0.617. Hence, the ratio between the estimated and measured Vmax* falls within the range 1/2 to 2 (90% error band) when q is predicted using CLASH NN. The new estimators derived in this study provide satisfactory estimations of Vmax* with a method simpler than those found in the literature. Neither the bottom slope nor the depth-induced wave breaking seem to significantly influence the dimensionless Vmax* in this study. OLT and OFV are directly related to the hydraulic stability of the armored crest and the pedestrian safety. Thus, OLT and OFV are required to properly design crest elevation using overtopping criteria. Neural Networks (NNs) are used in this study to develop new explicit unbiased estimators for the OLT and OFV exceeded by 2% of the incoming waves with a high coefficient of determination (0.866≤R2≤0.867). The appropriate number of significant figures of the empirical coefficients of such estimators is selected according to their variability. The optimum point where wave characteristics are determined to predict OLT and OFV was identified at a distance of 3h from the toe of the structure (where h is the water depth at the toe of the structure). The bottom slope does influence both OLT and OFV. The most extreme values of OLT and OFV are described with the 1-parameter Exponential and Rayleigh distribution functions, respectively, with satisfactory results (0.803≤R2≤0.812)., Al Ministerio de Educación, Cultura y Deporte, por la financiación brindada con el programa de Formación de Profesorado Universitario (FPU16/05081). Al Ministerio de Economía y Competitividad, por la financiación de los proyectos ESBECO (EStabilidad hidráulica del manto, BErmas y COronación de diques en talud con rebase y rotura por fondo, BIA2015-70436-R) y HOLOBREAK (Estabilidad Hidráulica y Transmisión de Diques Rompeolas Homogéneos de Baja Cota Diseñados a Rotura por Fondo, RTI2018-101073-B-I00-AR).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Numerical construction tests to assess the feasibility of placement grids for Cubipod Homogeneous Low-Crested Structures

  • Muñoz-Palao, Sergio
  • Díaz-Carrasco, Pilar
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Placement grid design is a key phase when constructing armor layers in mound breakwaters. Homogeneous Low-Crested Structures (HLCS) are low-crested structures designed as artificial reefs for marine colonization, coral reef regeneration and beach protection. The placement grid affects the construction feasibility, hydraulic stability and wave transmission of HLCS. This study presents a numerical methodology to simulate a realistic placement procedure for armor units during the construction of HLCS. This numerical simulator is based on the open-source physics engine Bullet Physics Engine (BPE), which applies Newton's laws of motion to rigid bodies. From an initial theorical placement grid for Cubipod HLCS, a series of numerical realistic unit placement tests are carried out to emulate the placement process at prototype scale; placement velocity and spatial deviation of crawler cranes are given parameters associated with each specific project. Considering the placement velocity and spatial deviation during construction, the quality of each specific placement grid is associated with the measured placement errors and the corresponding initial construction deviation to HLCS. This numerical methodology is valuable to understand the influence and the uncertaintly of the construction procedure of armor layers in mound breakwaters., This study was funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe under grants HOLOBREAK (RTI2018-101073-B-I00), REMOBE (PID2021-126475OB-I00) and HOLOBRACE (PID2021-128035OA-I00). The first author is grateful for the financial support of MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe under grant PRE2019-089542. The second author is funded through the Juan de la Cierva 2020 program (FJC2020-044778- I) by Union Europea NextGenerationEU en el marco del Plan de Recuperacion, Transformacion y Resiliencia de Espana , Spanish Ministry of Science and Innovation. The manuscript was revised by Debra Westall (Universitat Politecnica de Valencia, Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Individual wave overtopping volumes on mound breakwaters in breaking wave conditions and gentle sea bottoms

  • Mares-Nasarre, Patricia
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mound breakwaters are usually designed to limit the mean wave overtopping rate (q) or the maximum individual wave overtopping volume (V-max). However, rarely do studies focus on wave overtopping volumes on breakwaters in depth-limited breaking wave conditions. This study analyzes 2D physical tests on mound breakwaters with relevant overtopping rates (0.33 <= R-c/H-m0 <= 2.83) and three armor layers (Cubipod (R)-1L, rock-2L and cube-2L) in depth-limited breaking wave conditions (0.20 <= H-m0/h(s) <= 0.90) and with two bottom slopes (m = 1/25 and m = 1/50). The 2-parameter Weibull distribution was used to estimate V-max* = V-max/(gH(m0)T(01)(2)) with co-efficient of determination R-2 = 83.3%. In this study, the bottom slope (m = 1/50 and m = 1/25) did not significantly influence V-mox or the number of overtopping events, N-ow. During the design phase of a mound breakwater, q is required to use the methods given in the literature to estimate Thus, q must be estimated for design purposes when measured q is not available. In this study, CLASH Neural Network (CLASH NN) was used to estimate q with R-2 = 63.6%. If the 2-parameter Weibull distribution proposed in this study is used to estimate V-max with q estimated using CLASH NN, the prediction error of V-max* is R-2 = 61.7%. With the method presented in this study, the ratio between estimated and measured falls within the range 1/2 to 2 (90% error band) when q is estimated with CLASH NN. The new estimators derived in this study provide good predictions of N-ow and V-max with a method simpler than those in the literature on overtopped mound breakwaters in depth-limited breaking wave conditions on gentle sea bottoms (1/50 <= m <= 1/25)., The authors acknowledge the financial support from the Ministerio de Economia y Competitividad and Fondo Europeo de Desarrollo Regional (FEDER) under grant RTI2018-101073-B-I00, Universitat Politecnica de Valencia (Grant SP20180111), Primeros Proyectos de Investigacion (PAID06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia and Generalitat Valenciana (Grant AEST/2019/004). The first author was also financially supported through the FPU program (Formacion de Profesorado Universitario) funded by Ministerio de Educacion, Cultura y Deporte under grant FPU16/05081. The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic stability of cube-armored mound breakwaters in depth-limited breaking wave conditions

  • Mares-Nasarre, Patricia
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Armor erosion due to wave attack has been studied intensively since it is considered the main failure mode of mound breakwaters. Cube-armored mound breakwaters in depth-limited breaking wave conditions are common in practice but have received limited attention in the literature. In this study, 2D physical tests were performed on non-overtopped double-layer randomly-placed cube-armored mound breakwater models with armor slope cot¿ = 1.5 and bottom slope m = 2% in breaking wave conditions. Using the experimental results, a new hydraulic stability formula was derived with a coefficient of determination R2 = 0.85 based on a power relationship between the armor damage and the stability number and the dimensionless water depth. A lower hydraulic stability was found for the front slope of non-overtopped cube-armored structures in breaking wave conditions when compared to formulas given in the literature., The authors acknowledge the support from grant RTI2018-101073B-I00 funded by MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe", the Spanish Ministry of Economy and Competitiveness under grant BIA2012-33967, the Generalitat Valenciana under the grant AEST/2021/045 and FEDER. The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Armor Damage of Overtopped Mound Breakwaters in Depth-Limited Breaking Wave Conditions

  • Mares-Nasarre, Patricia
  • Argente, Gloria
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Armor damage due to wave attack is the principal failure mode to be considered when designing conventional mound breakwaters. Armor layers of mound breakwaters are typically designed using formulas in the literature for non-overtopped mound breakwaters in non-breaking wave conditions, although overtopped mound breakwaters in the depth-induced breaking wave zone are common design conditions. In this study, 2D physical tests with an armor slope H/V = 3/2 are analyzed in order to better describe the hydraulic stability of overtopped mound breakwaters with double-layer rock, double-layer randomly-place cube and single-layer Cubipod® armors in depth-limited breaking wave conditions. Hydraulic stability formulas are derived for each armor section (front slope, crest and rear slope) and each armor layer. The front slope of overtopped double-layer rock structures is more stable than the front slope of non-overtopped mound breakwaters in breaking wave conditions. When wave attack increases, armor damage appears first on the front slope, later on the crest and, finally, on the rear side. However, once the damage begins on the crest and rear side, the progression is much faster than on the front slope, because more wave energy is dissipated through the armored crest and rear side., The authors acknowledge the financial support from the Agencia Estatal de Investigacion and Fondo Europeo de Desarrollo Regional (FEDER) under grant RTI2018-101073-B-I00.
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publicación Artículo científico (JournalArticle)

Numerical construction tests to assess the feasibility of placement grids for Cubipod Homogeneous Low-Crested Structures

  • Muñoz-Palao, Sergio
  • Diaz-Carrasco, Pilar
  • Molines, Jorge
  • Gómez-Martín, M. Esther
  • Medina, Josep R.
Placement grid design is a key phase when constructing armor layers in mound breakwaters. Homogeneous Low-Crested Structures (HLCS) are low-crested structures designed as artificial reefs for marine colonization, coral reef regeneration and beach protection. The placement grid affects the construction feasibility, hydraulic stability and wave transmission of HLCS. This study presents a numerical methodology to simulate a realistic placement procedure for armor units during the construction of HLCS. This numerical simulator is based on the open-source physics engine Bullet Physics Engine (BPE), which applies Newton's laws of motion to rigid bodies. From an initial theorical placement grid for Cubipod HLCS, a series of numerical realistic unit placement tests are carried out to emulate the placement process at prototype scale; placement velocity and spatial deviation of crawler cranes are given parameters associated with each specific project. Considering the placement velocity and spatial deviation during construction, the quality of each specific placement grid is associated with the measured placement errors and the corresponding initial construction deviation to HLCS. This numerical methodology is valuable to understand the influence and the uncertaintly of the construction procedure of armor layers in mound breakwaters.