Pasar al contenido principal

ESTABILIDAD HIDRAULICA DE LOS MANTOS DE ESCOLLERA, CUBOS Y CUBIPODOS FRENTE A OLEAJE LIMITADO POR EL FONDO

BIA2012-33967

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Nacional de Proyectos de Investigación Fundamental
Subprograma Subprograma de Proyectos de Investigación Fundamental no Orientada
Convocatoria Proyectos I+D
Año convocatoria 2012
Plan Estatal 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Unidad de gestión Secretaría de Estado de Investigación, Desarrollo e Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Diseño y construcción de diques rompeolas, Design and construction of mound breakwaters

  • Medina, Josep R.|||0000-0001-5007-7426
  • Vidal, César
[ES] Se describe la evolución de las técnicas de diseño de los diques rompeolas y de algunos equipos y técnicas constructivas que los han impulsado. Se analiza sobre todo la influencia de las investigaciones teóricas y de laboratorio, desde los estudios y procedimientos pioneros de Iribarren hace 80 años hasta la construcción de diques protegidos con mantos monocapa de las últimas décadas y la optimización económica de las huellas energéticas y del carbono para una construcción sostenible. Se analiza el desarrollo de nuevos conceptos, la invención de nuevas formas geométricas para las unidades del manto, el gran impacto de las observaciones basadas en los ensayos físicos a escala reducida y la importancia de los condicionantes logísticos, métodos y técnicas de cada época para explicar la evolución en la manera de diseñar y construir grandes diques en talud a lo largo del tiempo., [EN] This paper describes the evolution of design techniques applied to mound breakwaters as well as some key tools, equipment and construction techniques. The influence of the theoretical and laboratory research is analyzed in detail, from the pioneering research by Iribarren eighty years ago to the construction of single-layer armored breakwaters in recent decades. The economic optimization and the new embodied energy and carbon concepts associated to the construction of mound breakwaters are studied. New concepts as well as the invention of new armor units are examined as is their impact based on the observations from small-scale physical experiments and the relevance of the equipment and logistic constraints to explain the evolution of the way mound breakwaters have been designed and built over time., Se agradece la financiación proporcionada por el Ministerio de Economía y Competitividad y FEDER (BIA2012-33967).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Toe berm design for very shallow waters on steep sea bottoms

  • Herrera Gamboa, María Piedad
  • Medina, Josep R.|||0000-0001-5007-7426
The toe berm is a relevant design element when rubble mound breakwaters are built on steep sea bottoms in breaking conditions. Different design formulas can be found in the literature to predict the damage caused to submerged toe berms placed on gentle bottom slopes. However, these formulas are not valid for very shallow waters in combination with steep sea bottoms where toe berms receive the full force of breaking waves. To guarantee breakwater stability in these conditions, new design formulas are needed for toe berms. To this end, physical model tests were carried out and data were analyzed to characterize rock toe berm stability in very shallow water and with a bottom slope m = 1/10. Based on test results, a new formula was developed with three parameters to estimate the nominal diameter (Dn50) of the toe berm rocks: water depth at the toe (hs), deep water significant wave height (Hs0), and deep water wave length (L0p)., The first author was financially supported through the FPU program (Formacion del Profesorado Universitario) funded by the Spanish Ministry of Education (Ministerio de Educacion, Cultura y Deporte) FPU13/01872. The authors also acknowledge financial support from the Spanish Ministry of Economy and Competitiveness (grant BIA2012-33967). The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Distribution of individual wave overtopping volumes on mound breakwaters

  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
  • Herrera, Maria P.
[EN] Conventional mound breakwaters are usually designed to withstand low mean wave overtopping discharges and a low proportion of overtopping waves (P-ow). Existing formulas to estimate P-ow, and maximum individual wave overtopping volume are usually based on tests with high P-ow; this study is focused on mound breakwaters subjected to P-ow, < 0.2. The performance of the 2-parameter Weibull and Exponential distributions is examined in order to describe individual wave overtopping volumes of mound breakwaters in non-breaking wave conditions. A new methodology is applied to 164 small-scale 2D physical tests to identify the number of overtopping waves, and the corresponding individual wave overtopping volumes. Utility functions are used to consider the relative relevance of the observed data: in this study, a quadratic utility function depending on all the individual wave overtopping volumes and step utility functions with 10%, 30% and 50% of the highest volumes are used to fit the Weibull and Exponential distributions. In this study, a new estimator of P-ow is proposed to improve the predictions required to estimate the maximum individual wave overtopping volume. Existing estimators of P-ow, underpredict the largest values of P-ow, measured in the physical tests. The parameters fitted to the Weibull and Exponential distributions using the quadratic utility function provide estimations of the dimensionless maximum individual wave overtopping volume with relative mean squared errors rMSE = 10.4% and 10.6%, respectively. When CLASH Neural Network-estimated mean overtopping rates are used to predict the maximum individual wave overtopping with the quadratic utility function, the 2-parameter Weibull and Exponential distributions provide rMSE = 31.6% and rMSE = 33.3%, respectively. The new estimators proposed in this study improve the predictions of P-ow and maximum individual wave overtopping volumes on conventional mound breakwaters designed for low wave overtopping rates., The authors are grateful for financial support from European FEDER and Spanish Ministerio de Economia y Competitividad (Grants BIA2012-33967 and BIA2015-70435-R), SATO (OHL Group), Universitat Politecnica de Valencia (Grant SP20180111, Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia) and CDTI (Centro para el Desarrollo Tecnologico e Industrial). The authors also thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Calibration of overtopping roughness factors for concrete armor units in non-breaking conditions using the CLASH database

  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
The roughness factor (γf) is a parameter used in overtopping estimators to account for the effects of armor unit geometry, the number of layers in the armor and other structural characteristics. Different values of γf for the same armors are given in the literature; however, in this study, the value of γf was calibrated for each overtopping estimator using the best available overtopping data. A methodology based on a bootstrapping technique is proposed to statistically characterize the roughness factors which best fit each formula. For each selected armor unit and overtopping formula, three percentiles (10%, 50% and 90%) of γf are given. Five sets of γf are given for five different overtopping estimators, calibrated using overtopping data from the CLASH database and additional tests with Cubipod armors in non-breaking conditions. The results indicate differences up to 20% in the optimum values of γf compared to those given in the literature. Optimum roughness factors are provided for the CLASH neural network (CLNN); the CLNN was found to be a better overtopping estimator than the other four overtopping formulas compared in this study. The γf is dependent on both the overtopping estimator and the dataset used. Armor porosity affects not only armor roughness and overtopping but also armor hydraulic stability; thus, recommended packing densities must be followed to avoid changes in porosity during lifetime. The sensitivity of the overtopping prediction to the roughness factor depends on the relative crest freeboard (Rc/Hm0); the greater the Rc/Hm0, the higher the sensitivity., The authors are grateful for financial support from Spanish Ministerio de Economia y Competitividad (Grant BIA2012-33967). The first author was funded through the FPU program (Formacion del Profesorado Universitario, Grant AP2010-4366) by the Spanish Ministerio de Educacion, Cultura y Deporte. The authors also thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic stability of nominal and sacrificial toe berms for mound breakwaters on steep sea bottoms

  • Herrera Gamboa, María Piedad
  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] When mound breakwaters are placed on steep sea bottoms in combination with very shallow waters, the design of the toe berm becomes a relevant issue. Toe berms built close to the water surface on a steep sea bottom must withstand such high wave loads that their design may not be feasible with available quarrystones. In this study, a new design method was developed to reduce the rock size by increasing the toe berm width. The analysis involved specific 2D small-scale tests with toe berms of different rock sizes and widths, placed on a m = 1/10 bottom slope with the water surface close to the toe berm crest. Two new concepts were introduced to better characterize damage to wide toe berms: (1) the most shoreward toe berm area which effectively supports the armor layer, in this study referred to as the primary or nominal toe berm and (2) the most seaward toe berm area which serves to protect the nominal toe berm, in this study called the secondary or the sacrificial toe berm. Damage to the nominal toe berm was used to describe hydraulic stability of wider toe berms. Given a standard toe berm of three rocks wide (nominal toe berm), an equivalent toe berm with damage similar to the nominal toe berm was defined by increasing the berm width and decreasing the rock size. The reduction in rock size showed an inverse 0.4-power relation with the relative berm width.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of armour porosity on the hydraulic stability of cube armour layers

  • Medina, Josep R.|||0000-0001-5007-7426
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
Armour placement and packing density directly affect construction costs and hydraulic performance of mound breakwaters. In this paper, the literature concerning the influence of armour porosity on the hydraulic stability of single- and double-layer armours is discussed. Qualitative and quantitative estimations for the influence of armour porosity and packing density on the hydraulic stability are given for the most common concrete armour units. The analysis focuses on specific 2D hydraulic stability tests of double-layer randomly-placed cube armours with different armour porosities and permeable core. The stability number showed a 1.2-power relationship with the packing density for double-layer randomly-placed cube armours considering armour unit extraction and Heterogeneous Packing. The literature review and experimental results with small-scale breakwater models protected with a variety of armour units clearly indicate that a significant increase in armour porosity above the recommended values substantially decreases armour hydraulic stability. To avoid uncontrolled model effects, packing density should be routinely measured in small-scale tests, and armour placement techniques should be monitored at prototype scale. The actual packing density obtained in small-scale models and prototypes has to be explicitly reported, because packing density significantly affects hydraulic stability during service time. (C) 2014 Elsevier Ltd. All rights reserved., The authors are grateful for financial support from European FEDER and Spanish Ministerio de Economia y Competitividad (Grant BIA2012-33967) and CDTI (CUBIPOD and CLIOMAR Projects). The second author was funded through the FPU program (Formacion del Profesorado Universitario, Grant AP2010-4366) by the Spanish Ministerio de Educacion, Cultura y Deporte. The authors also thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic stability of rock armors in breaking wave conditions

  • Herrera Gamboa, María Piedad
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Armor layers of mound breakwaters are usually designed with empirical formulas based on small-scale tests in non-breaking wave conditions. However, most rubble mound breakwaters are constructed in the depth-induced breaking zone, where they must withstand design storms having some percentage of large waves breaking before reaching the structure; in these cases, the design formulas for non-breaking wave conditions are not fully valid. To characterize double-layer rock armor damage in breaking wave conditions, 2D physical model tests were carried out with a bottom slope m=1/50. In order to develop a simple method to determine the wave parameters in the depth-induced breaking zone, experimental wave measurements were compared to the numerical estimations given by the SwanOne model. An analysis was conducted to select the best characteristic wave height to estimate rock armor damage when dealing with depth-induced breaking waves; the spectral significant wave height, Hm0, estimated at a distance of 3hs seaward from the structure toe, was found to be the most adequate. A new hydraulic stability formula is proposed for double-layer rock armors in breaking wave conditions, considering the observed potential 6-power relationship between the equivalent dimensionless armor damage and the Hm0 at 3hs seaward distance from the structure toe., The authors acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness (grants BIA2012-33967 and BIA2015-70436-R). The first author was financially supported through the FPU program (Formacion del Profesorado Universitario) funded by the Spanish Ministry of Education (Ministerio de Educacion, Cultura y Deporte) FPU13/01872. The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Explicit wave overtopping formula for mound breakwaters with crown walls using CLASH neural network-derived data

  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
Based on the Crest Level Assessment of Coastal Structures (CLASH) Neural Network Overtopping prediction method, a new 16-parameter overtopping estimator (Q6) was developed for conventional mound breakwaters with crown walls, both with and without toe berms. Q6 was built up using the overtopping estimations given by the CLASH Neural Network and checked using the CLASH database. Q6 was compared to other conventional overtopping formulas, and the Q6 obtained the lowest prediction errors. Q6 provides overtopping predictions similar to the CLASH Neural Network for conventional mound breakwaters but using only six explanatory dimensionless variables (Rc=Hm0; Ir; Rc=h;Gc=Hm0; Ac=Rc, and a toe berm variable based on Rc=h) and two reduction factors (g f and g b ). Q6 describes explicit relationships between input variables and overtopping discharge, and hence it facilitates use in engineering design to identify costeffective solutions and to quantify the influence of variations in wave and structural parameters., The authors are grateful for financial support from the Spanish Ministerio de Economia y Competitividad (Grant BIA2012-33967). The first author was funded through the FPU program (Formacion del Profesorado Universitario, Grant AP2010-4366) by the Spanish Ministerio de Educacion, Cultura y Deporte. The authors also thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic stability of cube-armored mound breakwaters in depth-limited breaking wave conditions

  • Mares-Nasarre, Patricia
  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Armor erosion due to wave attack has been studied intensively since it is considered the main failure mode of mound breakwaters. Cube-armored mound breakwaters in depth-limited breaking wave conditions are common in practice but have received limited attention in the literature. In this study, 2D physical tests were performed on non-overtopped double-layer randomly-placed cube-armored mound breakwater models with armor slope cot¿ = 1.5 and bottom slope m = 2% in breaking wave conditions. Using the experimental results, a new hydraulic stability formula was derived with a coefficient of determination R2 = 0.85 based on a power relationship between the armor damage and the stability number and the dimensionless water depth. A lower hydraulic stability was found for the front slope of non-overtopped cube-armored structures in breaking wave conditions when compared to formulas given in the literature., The authors acknowledge the support from grant RTI2018-101073B-I00 funded by MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe", the Spanish Ministry of Economy and Competitiveness under grant BIA2012-33967, the Generalitat Valenciana under the grant AEST/2021/045 and FEDER. The authors thank Debra Westall for revising the manuscript.