Pasar al contenido principal

ESTABILIDAD HIDRAULICA DEL MANTO, BERMAS Y CORONACION DE DIQUES EN TALUD CON REBASE Y ROTURA POR FONDO

BIA2015-70436-R

•
Nombre agencia financiadora Ministerio de Economía y Competitividad
Acrónimo agencia financiadora MINECO
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2015
Plan Estatal 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Unidad de gestión Dirección General de Investigación Científica y Técnica
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA
Identificador persistente http://dx.doi.org/10.13039/501100003329

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Influence of Mild Bottom Slopes on the Overtopping Flow over Mound Breakwaters under Depth-Limited Breaking Wave Conditions

  • Mares-Nasarre, Patricia
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] The crest elevation of mound breakwaters is usually designed considering a tolerable mean wave overtopping discharge. However, pedestrian safety, characterized by the overtopping layer thickness (OLT) and the overtopping flow velocity (OFV), is becoming more relevant due to the reduction of the crest freeboards of coastal structures. Studies in the literature focusing on OLT and OFV do not consider the bottom slope effect, even if it has a remarkable impact on mound breakwater design under depth-limited breaking wave conditions. Therefore, this research focuses on the influence of the bottom slope on OLT and OFV exceeded by 2% of incoming waves, hc,2% and uc,2%. A total of 235 2D physical tests were conducted on conventional mound breakwaters with a single-layer Cubipod® and double-layer rock and cube armors with 2% and 4% bottom slopes. Neural networks were used to determine the optimum point to estimate wave characteristics for hc,2% and uc,2% calculation; that point was located at a distance from the model toe of three times the water depth at the toe (hs) of the structure. The influence of the bottom slope is studied using trained neural networks with fixed wave conditions in the wave generation zone; hc,2% slightly decreases and uc,2% increases as the gradient of the bottom slope increases., This research was funded by Ministerio de Economia y Competitividad and the Fondo Europeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R and RTI2018-101073-B-I00. The first author was also financially supported by the Ministerio de Educacion, Cultura y Deporte through the FPU program (Formacion de Profesorado Universitario) under grant FPU16/05081.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Distribution of individual wave overtopping volumes on mound breakwaters

  • Molines, Jorge|||0000-0001-7850-0759
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
  • Herrera, Maria P.
[EN] Conventional mound breakwaters are usually designed to withstand low mean wave overtopping discharges and a low proportion of overtopping waves (P-ow). Existing formulas to estimate P-ow, and maximum individual wave overtopping volume are usually based on tests with high P-ow; this study is focused on mound breakwaters subjected to P-ow, < 0.2. The performance of the 2-parameter Weibull and Exponential distributions is examined in order to describe individual wave overtopping volumes of mound breakwaters in non-breaking wave conditions. A new methodology is applied to 164 small-scale 2D physical tests to identify the number of overtopping waves, and the corresponding individual wave overtopping volumes. Utility functions are used to consider the relative relevance of the observed data: in this study, a quadratic utility function depending on all the individual wave overtopping volumes and step utility functions with 10%, 30% and 50% of the highest volumes are used to fit the Weibull and Exponential distributions. In this study, a new estimator of P-ow is proposed to improve the predictions required to estimate the maximum individual wave overtopping volume. Existing estimators of P-ow, underpredict the largest values of P-ow, measured in the physical tests. The parameters fitted to the Weibull and Exponential distributions using the quadratic utility function provide estimations of the dimensionless maximum individual wave overtopping volume with relative mean squared errors rMSE = 10.4% and 10.6%, respectively. When CLASH Neural Network-estimated mean overtopping rates are used to predict the maximum individual wave overtopping with the quadratic utility function, the 2-parameter Weibull and Exponential distributions provide rMSE = 31.6% and rMSE = 33.3%, respectively. The new estimators proposed in this study improve the predictions of P-ow and maximum individual wave overtopping volumes on conventional mound breakwaters designed for low wave overtopping rates., The authors are grateful for financial support from European FEDER and Spanish Ministerio de Economia y Competitividad (Grants BIA2012-33967 and BIA2015-70435-R), SATO (OHL Group), Universitat Politecnica de Valencia (Grant SP20180111, Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia) and CDTI (Centro para el Desarrollo Tecnologico e Industrial). The authors also thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Overtopping layer thickness and overtopping flow velocity on mound breakwaters

  • Mares-Nasarre, Patricia
  • Argente-Garrido, Gloria Maria
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mound breakwater design is evolving owing to rising sea levels caused by climate change and social concern regarding the visual impact of coastal structures. The crest freeboard of coastal structures tends to decrease while overtopping hazard increases over time. Pedestrian safety when facing overtopping events on coastal structures has been assessed considering the overtopping layer thickness (OLT) and overtopping flow velocity (OFV). This paper proposes a new method to estimate the OLT and OFV on mound breakwater crests during extreme overtopping events, based on 123 2D small-scale physical tests of conventional low-crested mound breakwaters with a single-layer Cubipod® and double-layer rock and cube armors. The new method to estimate OLT exceeded by 2% of incoming waves is based on formulas given in literature for dikes, but adapted and calibrated for mound breakwaters. The formula to estimate the OFV exceeded by 2% of incoming waves is based on the correlation between the statistics of the OLT and OFV, considering an empirical coefficient calibrated for each type of armor layer. Exponential and Rayleigh distribution functions are proposed for estimating the OLT and OFV with exceedance probabilities under 2%. Although the statistics of OLT and OFV depend on similar variables, contrary to intuition, specific OLT and OFV corresponding to the same overtopping event appear to be independent., The authors acknowledge the financial support from the Ministerio de Economfa y Competitividad and the Fondo Europeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R, and from the Conselleria d'Educacio, Investigacia, Cultura i Esport (Generalitat Valenciana) under grant GV/2017/031. The first author was financially supported through the FPU program (Formacion de Profesorado Universitario) funded by the Ministerio de Education, Cultura y Deporte under grant FPU16/05081.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic Stability of the Armor Layer of Overtopped Breakwaters

  • Argente-Garrido, Gloria Maria
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Mound breakwaters with significant overtopping rates in depth-limited conditions are common in practice due to social concern about the visual impact of coastal structures and sea level rise due to climatic change. For overtopped mound breakwaters, the highest waves pass over the crest producing armor damage, not only to the front slope, but also to the crest and the rear slope. To guarantee the breakwater stability, it is necessary to limit the armor damage in the three parts of the structure: Front slope, crest, and rear slope. This paper describes the hydraulic stability of the armor layer of medium and low-crested structures in wave breaking conditions. Small-scale physical model tests were carried out with different relative crest freeboards and three armor units: Rocks, cubes, and Cubipods. The armor damage progression in the front slope, crest, and rear slope was analyzed using the Virtual Net method to consider the heterogeneous packing and porosity evolution along the armor slope. A comparison is provided between the hydraulic stability of the different armors and their relationship with the measured overtopping volumes., This research was funded by Ministerio de Economia y Competitividad and the FondoEuropeo de Desarrollo Regional (FEDER) under grant BIA2015-70436-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Estimations of wave forces on crown walls based on wave overtopping rates

  • Molines, Jorge|||0000-0001-7850-0759
  • Medina, Josep R.|||0000-0001-5007-7426
  • Herrera Gamboa, María Piedad
[EN] In this study, seven input variables are used to estimate wave forces on the crown wall, and explanatory variables are ranked using neural network techniques. 274 small-scale 2D tests, including both wave overtopping and pressure on crown-wall measurements, were used to calibrate the wave force predictors. Wave overtopping (log Q) was the most relevant variable to estimate horizontal wave forces and overturning moments, while the relative foundation level (F-e/L-0p) was the most relevant variable to estimate wave up-lift forces. The new wave force estimators showed prediction errors slightly higher than the formulas given in the literature, but using fewer parameters and explanatory variables. The range of application of the new formulas is 1.67 < R-c/(gamma(f) H-m0) < 6.55, 1.39 < xi(0p) < 7.77, 0.36 < gamma(f) R-u0.1%/R-c < 1.41, 0.00 < (R-c-A(c))/C-h < 0.59, 2.64 < root L-m/G(c) < 6.54, 0.00 < F-c/ L-0p < 0.03 and -6.00 < logQ < -2.78. Compared to pressure on crown walls, the mean wave overtopping rate is relatively easy to measure in small-scale tests and prototypes. The new estimators of wave forces on the crown wall can be used to indirectly calculate forces on models when only overtopping rates are measured. If wave overtopping is one order of magnitude higher, the wave forces and overturning moments on the crown wall increase between 11% and 60%, considerably reducing the crown wall stability., The authors acknowledge financial support from European FEDER and Spanish Mirtisterio de Economia y Competitividad (Grant BIA2015-70436-R), SATO (OHL Group) and CDTI. The second author was funded through the FPU program (Formacion del Profesorado Universitario, Grant FP2013/01872) by the Spanish Ministerio de Educacion, Culturay Deporte. The authors thank Debra Westall for revising the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Overtopping flow on mound breakwaters under depth-limited breaking wave conditions

  • Mares Nasarre, Patricia
[ES] El cambio climático y la conciencia social sobre el impacto de las infraestructuras en el medio está llevando a la necesidad de diseñar diques en talud con cotas de coronación reducidas frente a eventos de rebase más extremos. Además, la mayoría de estos diques se construyen en zonas de profundidades reducidas, donde el oleaje rompe a causa de la limitación por fondo. Estudios recientes apuntan a la necesidad de considerar no sólo la caudal medio de rebase (q) sino también el máximo volumen individual de rebase (Vmax), el espesor de lámina de agua (OLT) y la velocidad del flujo de rebase (OFV) en el diseño de la cota de coronación de un dique en talud según criterios de rebase. No obstante, existen pocos estudios en la literatura científica centrados en Vmax en estructuras costeras sometidas a oleaje limitado por fondo. Además, estos estudios proporcionan resultados contradictorios en relación a la influencia de la limitación por fondo del oleaje sobre Vmax. En cuanto a OLT y OFV, no se han encontrado estudios en la literatura científica que permitan su predicción en diques en talud. En esta tesis doctoral, se han realizado ensayos físicos 2D en diques en talud rebasables (0.3≤Rc/Hm0≤2.5) sin espaldón y con tres mantos principales (Cubípodo®-1L, cubo-2L y escollera-2L) sobre dos pendientes de fondo suaves (m=2% and 4%) en condiciones de oleaje limitado por fondo (0.2≤Hm0/h≤0.9). Vmax junto con q son las variables más recomendadas en la literatura científica para diseñar la cota de coronación de diques en talud según criterios de rebase. En el presente estudio, los mejores resultados en la estimación de Vmax*=Vmax/(gHm0T012) se han obtenido empleando la función de distribución Weibull de dos parámetros con un coeficiente de determinación R2=0.833. Durante la fase de diseño de un dique en talud, es necesario predecir q para calcular Vmax cuando se emplean los métodos dados en la literatura científica. Por tanto, se debe estimar q con fines de diseño si no se dispone de observaciones directas. En caso de emplear la red neuronal CLASH NN para estimar q (R2=0.636), la bondad de ajuste de la función de distribución Weibull de dos parámetros propuesta en esta tesis para predecir Vmax* es R2=0.617. Así, el ratio entre Vmax* medido y estimado cae dentro del rango de 1/2 a 2 (banda de confianza del 90%) cuando se emplea q estimado con CLASH NN. Los nuevos estimadores desarrollados en la presente disertación proporcionan resultados satisfactorios en la predicción de Vmax* con un método más simple que aquellos propuestos en la literatura científica. No se ha encontrado una influencia significativa de la pendiente de fondo ni de la limitación por fondo del oleaje sobre Vmax* en este estudio. OLT y OFV están directamente relacionados con la estabilidad hidráulica de la coronación del dique y la seguridad peatonal frente a rebase. Por tanto, se requiere estimar OLT y OFV en la coronación del dique para diseñar apropiadamente su cota de coronación empleando criterios de rebase. En este estudio, se han empleado redes neuronales para desarrollar nuevos estimadores explícitos que permiten predecir OLT y OFV superados por el 2% del oleaje incidente con un alto coeficiente de determinación (0.866≤R2≤0.867). El número de cifras significativas apropiado para los coeficientes experimentales de dichos estimadores se ha determinado en base a su variabilidad. El punto óptimo en el que las características del oleaje deben ser estimadas para predecir OLT y OFV se ha identificado a una distancia de 3h desde el pie de la estructura (siendo h la profundidad a pie de dique). La pendiente de fondo tiene influencia sobre OLT y OFV. Los valores más extremos de OLT y OFV se han descrito empleando las distribuciones Exponencial de un parámetro y Rayleigh, respectivamente, con resultados satisfactorios (0.803≤R2≤0.812)., [CA] El canvi climàtic i la consciència social sobre l'impacte de les infraestructures al medi està portant a la necessitat de dissenyar dics en talús amb cotes de coronació reduïdes front a esdeveniments d'ultrapassament més extrems. A més, la majoria dels dics es construeixen en zones amb profunditats reduïdes on l'onatge es trenca a causa de la limitació per fons. Estudis recents apunten a la necessitat de considerar no solament el cabal mitjà de sobrepasse (q) sinó també el màxim volum individual de sobrepasse (Vmax), l'espessor de la làmina d'aigua (OLT) i la velocitat del flux de sobrepasse (OFV) pel disseny de la cota de coronació d'un dic en talús segons criteris de sobrepasse. No obstant, existeixen pocs estudis a la literatura científica centrats en Vmax en estructures costeres sotmeses a onatge limitat per fons. Addicionalment, aquests estudis proporcionen resultats contradictoris en relació a la influència de la limitació per fons de l'onatge sobre Vmax. Quant a OLT i OFV, no s'han trobat estudis a la literatura científica que permeten la seua predicció a dics en talús. En aquesta tesi doctoral, s'han realitzat assajos físics 2D amb dics en talús amb sobrepassos rellevants (0.3≤Rc/Hm0≤2.5) sense espatlló i amb tres elements al mantell principal (Cubípode-1L, cubs-2L i esculleres-2L) ubicats sobre pendents de fons suaus (m=2% i 4%) en condicions d'onatge limitat pel fons (0.2≤Hm0/h≤0.9). Vmax conjuntament amb q són les variables més recomanades a la literatura científica per dissenyar la cota de coronació en dics en talús segons criteris d'ultrapassament. Al present estudi, els millors resultats en l'estimació de Vmax*=Vmax/(gHm0T012) s'han obtingut utilitzant la funció de distribució Weibull de dos paràmetres amb un elevat coeficient de determinació R2=0.833. Durant la fase de disseny d'un dic en talús, és necessari predir q per calcular Vmax quan s'utilitzen els mètodes donats a la literatura científica. Per tant, es deu estimar q amb fins de disseny si no es disposa d'observacions directes. Si s'aplica la xarxa neuronal de CLASH NN per estimar q (R2=0.636), la bondat d'ajust de la funció de distribució Weibull de dos paràmetres proposada a aquesta tesi per predir Vmax* és R2=0.617. Així doncs, el ràtio entre el Vmax* mesurat i estimat es troba dins del rang de 1/2 a 2 (banda de confiança del 90%) quan s'usa q predit amb CLASH NN. Els nous estimadors desenvolupats a aquesta dissertació proporcionen resultats satisfactoris en la predicció de Vmax* amb un mètode més senzill que aquells proposats a la literatura científica. No s'ha trobat una influència significativa de la pendent de fons ni de la limitació de l'onatge per fons sobre Vmax* a aquest estudi. OLT i OFV estan directament relacionats amb l'estabilitat hidràulica de la coronació de dics i la seguretat de vianants front a ultrapassaments. Per tant, es requereix estimar OLT i OFV en la coronació de dics per dissenyar apropiadament la seua cota de coronació utilitzant criteris de sobrepasse. En aquest estudi, s'han usat xarxes neuronals per desenvolupar nous estimadors explícits que permeten predir OLT i OFV superats pel 2% de l'onatge incident amb un elevat coeficient de determinació (0.866≤R2≤0.867). El nombre de xifres significatives apropiat per als coeficients experimentals dels mencionats estimadors s'ha determinat basant-se en la seua variabilitat. El punt òptim on determinar les característiques de l'onatge deuen ser estimades per predir OLT i OFV s'ha identificat a una distància de 3h des del peu de l'estructura (on h és la profunditat a peu de dic). La pendent de fons té influència sobre OLT i OFV. Els valors més extrems de OLT i OFV s'han descrit amb les distribucions Exponencial d'un paràmetre i Rayleigh, respectivament, amb resultats satisfactoris (0.803≤R2≤0.812)., [EN] Climate change and the social concern about the impact of infrastructures is leading to mound breakwaters with reduced crest freeboards facing higher extreme overtopping events. In addition, most mound breakwaters are built in the surf zone where depth-limited wave breaking takes place. Recent studies point out the need of considering not only the mean wave overtopping discharge (q) but also the maximum individual wave overtopping volume (Vmax), the overtopping layer thickness (OLT) and the overtopping flow velocity (OFV) when designing mound breakwater crest elevation using overtopping criteria. However, few studies in the literature are focused on Vmax on coastal structures under depth-limited breaking wave conditions. In addition, those few studies report contradictory conclusions regarding the significance of depth-limited breaking waves on Vmax. With respect to OLT and OFV, no studies are found in the literature for their prediction on mound breakwaters. In this PhD thesis, 2D physical model tests were conducted on overtopped mound breakwaters (0.3≤Rc/Hm0≤2.5) without a crown wall armored with three armor layers (Cubipod®-1L, cube-2L and rock-2L) on two gentle bottom slopes (m=2% and 4%) in depth-limited breaking wave conditions (0.2≤Hm0/h≤0.9). Vmax together with q are the most recommended variables in the literature to design mound breakwater crest elevation based on overtopping criteria. In the present study, the 2-parameter Weibull distribution provides the best results when estimating Vmax*=Vmax/(gHm0T012) with coefficient of determination R2=0.833. During the design phase of a mound breakwater, q is needed to predict Vmax using methods given in the literature. Thus, q must be estimated for design purposes when direct observations are not available. If CLASH NN is used to estimate q (R2=0.636), the goodness-of-fit of the 2-parameter Weibull distribution proposed in this thesis to predict Vmax* is R2=0.617. Hence, the ratio between the estimated and measured Vmax* falls within the range 1/2 to 2 (90% error band) when q is predicted using CLASH NN. The new estimators derived in this study provide satisfactory estimations of Vmax* with a method simpler than those found in the literature. Neither the bottom slope nor the depth-induced wave breaking seem to significantly influence the dimensionless Vmax* in this study. OLT and OFV are directly related to the hydraulic stability of the armored crest and the pedestrian safety. Thus, OLT and OFV are required to properly design crest elevation using overtopping criteria. Neural Networks (NNs) are used in this study to develop new explicit unbiased estimators for the OLT and OFV exceeded by 2% of the incoming waves with a high coefficient of determination (0.866≤R2≤0.867). The appropriate number of significant figures of the empirical coefficients of such estimators is selected according to their variability. The optimum point where wave characteristics are determined to predict OLT and OFV was identified at a distance of 3h from the toe of the structure (where h is the water depth at the toe of the structure). The bottom slope does influence both OLT and OFV. The most extreme values of OLT and OFV are described with the 1-parameter Exponential and Rayleigh distribution functions, respectively, with satisfactory results (0.803≤R2≤0.812)., Al Ministerio de Educación, Cultura y Deporte, por la financiación brindada con el programa de Formación de Profesorado Universitario (FPU16/05081). Al Ministerio de Economía y Competitividad, por la financiación de los proyectos ESBECO (EStabilidad hidráulica del manto, BErmas y COronación de diques en talud con rebase y rotura por fondo, BIA2015-70436-R) y HOLOBREAK (Estabilidad Hidráulica y Transmisión de Diques Rompeolas Homogéneos de Baja Cota Diseñados a Rotura por Fondo, RTI2018-101073-B-I00-AR).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Hydraulic stability of rock armors in breaking wave conditions

  • Herrera Gamboa, María Piedad
  • GÓMEZ-MARTÍN, M. ESTHER|||0000-0003-1555-4383
  • Medina, Josep R.|||0000-0001-5007-7426
[EN] Armor layers of mound breakwaters are usually designed with empirical formulas based on small-scale tests in non-breaking wave conditions. However, most rubble mound breakwaters are constructed in the depth-induced breaking zone, where they must withstand design storms having some percentage of large waves breaking before reaching the structure; in these cases, the design formulas for non-breaking wave conditions are not fully valid. To characterize double-layer rock armor damage in breaking wave conditions, 2D physical model tests were carried out with a bottom slope m=1/50. In order to develop a simple method to determine the wave parameters in the depth-induced breaking zone, experimental wave measurements were compared to the numerical estimations given by the SwanOne model. An analysis was conducted to select the best characteristic wave height to estimate rock armor damage when dealing with depth-induced breaking waves; the spectral significant wave height, Hm0, estimated at a distance of 3hs seaward from the structure toe, was found to be the most adequate. A new hydraulic stability formula is proposed for double-layer rock armors in breaking wave conditions, considering the observed potential 6-power relationship between the equivalent dimensionless armor damage and the Hm0 at 3hs seaward distance from the structure toe., The authors acknowledge the financial support from the Spanish Ministry of Economy and Competitiveness (grants BIA2012-33967 and BIA2015-70436-R). The first author was financially supported through the FPU program (Formacion del Profesorado Universitario) funded by the Spanish Ministry of Education (Ministerio de Educacion, Cultura y Deporte) FPU13/01872. The authors thank Debra Westall for revising the manuscript.