Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

X-ray absorptiometry and ultrasound technologies for non-destructive compositional analysis of dry-cured ham

  • Fulladosa, E.
  • PRADOS PEDRAZA, MARTA DE
  • Muñoz, I
  • Arnau, J.
  • Gou, Pere
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] The characterization of dry-cured ham according to salt and fat contents is of great interest to industry and consumers. In this study, the feasibility of using non-destructive technologies such as X-rays and ultrasound (US) for this purpose was evaluated in dry-cured ham portions. Predictive models for fat and salt contents were based on the measurement of X-ray attenuation at different incident energies and the US velocity when the ham was at 2 and 15 degrees C. A semi-empirical model based on the US measurements was also developed. Salt content was better predicted by X-ray technology (RMSEV = 0.43%) than US (RMSEV = 0.69%) and their combination had little impact on the accuracy of the prediction. US predicted fat content slightly better (RMSEV = 6.70%) than X-rays (RMSEV = 7.00%), and their combination increased the accuracy of the prediction (RMSEV = 5.60%). Using the best models, 81% of samples were correctly classified into three salt content categories with X-rays whereas 71% of samples were correctly classified into three fat content categories by combining X-rays and US. (C) 2015 Elsevier Ltd. All rights reserved., This work was supported by Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) (contract n. RTA2010-00029-CO4-01/02) and by Universitat Politecnica de Valencia (UPV) through the FPI-2011 Grant awarded to Marta de Prados.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Non-destructive determination of fat content in green hams using ultrasound and X-rays

  • PRADOS PEDRAZA, MARTA DE
  • Fulladosa, E.
  • GOU, P.
  • Muñoz, I
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] This work addresses the use of ultrasound (US) and medical dual energy X-ray absorptiometry methods to predict the fat content in green pork hams. Ultrasonic velocity (õ) and X-ray absorption were measured in 78 green hams. An increase in the fat content involved an increase in õ and a decrease in the X-ray attenuationmeasured at 2 °C.Models developed to predict the fat content fromthe ultrasonic velocity or X-ray parameters provided errors of 2.97% and 4.65%, respectively. The combination of both US and X-ray technologies did not improve prediction accuracy. These models allowed green hams to be classified into three levels of fatness, with 88.5% and 65.4% of the hams correctly classified when using models based on ultrasonic and X-ray parameters, respectively. Therefore, US and X-rays emerge as useful quality control technologies with which to estimate the fat content in green pork hams, This work was supported by the spanish Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) (contracts n. RTA2010-00029-CO4-01/02) and by Universitat Politecnica de Valencia (UPV) through the FPI grant given to Marta de Prados (SP-1.2011-S1-2757).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Advances in the Ultrasound Characterization Of Dry-Cured Meat Products

  • Corona Jiménez, Edith
  • Gómez Álvarez-Arenas, Tomas E.
  • Watson, Nicholas
  • Povey, Malcolm J.W.
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] In this work, the feasibility of using non-contact ultrasonic techniques (air-coupled and scanning acoustic microscopy, SAM) for characterizing different dry-cured meat products was assessed. Air-coupled ultrasonic measurements were performed on vacuum packaged sliced dry-cured ham, and compared with contact measurements. The average ultrasonic velocity in dry-cured ham was 1846 +/- 49 m/s and 1842 +/- 42 m/s for air-coupled and contact measurements, respectively. The deviation (1% relative error) between both techniques was related to the influence of the heterogeneous structure and composition of dry-cured ham and the transducer focusing. The SAM was used to characterize dry-cured ham and chorizo samples. B-scan images for dry-cured ham and chorizo showed two dominant reflections from the sample, linked to reflections in the lean and fatty tissues. The results indicate that contact ultrasonic measurements could be replaced by the air-coupled technique, reducing the measuring time and the material handling. On the other hand, SAM technique allows the microscopic characterization of dry-cured meat products. (C) 2013 Elsevier Ltd. All rights reserved., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad" in Spain through the Projects RTA 2010-00029-C04-02 and DPI2011-22438.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic characterization of the fat source and composition of formulated dry-cured meat products

  • Corona Jiménez, Edith
  • Ventanas Canillas, Sonia
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] The aim of this work was to test the feasibility of using ultrasonic measurements to estimate the fat content and identify the fat sources used in formulated dry-cured pork meat products. For that purpose, dry-cured sausages were prepared using different fat sources (two Iberian pork backfats, Iberian lard, and sunflower oil) and contents (fat content from 3% to 17% wet basis) and characterized by measuring the ultrasonic velocity (at 2?, 6?, 10?, 15?, 20?, and 25?), fatty acid profile, thermal behavior, and composition. The fatty acid composition affected the melting behavior of the sausages, which also involved different ultrasonic velocities, depending on the fat source used for the sausage formulation. Significant (p<0.05) linear relationships were established between the ultrasonic velocity and the percentage of melted fat, by means of which the sausage batches were differentiated according to the fat source used. The ultrasonic velocity temperature dependence allowed the determination of the fat content (explained variance 96.1%) by measuring the ultrasonic velocity in the dry-cured sausages at 2? and 25? and using a semi-empirical equation. Therefore, the ultrasonic measurements could be considered as a reliable tool for the characterization and differentiation of formulated dry-cured meat products with different fat sources and contents., The authors acknowledge the financial support from the 'Ministerio de Ciencia e Innovacion' in Spain (Project RTA 2010-00029-C04-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Non-destructive salt content prediction in brined pork meat using ultrasound technology

  • PRADOS PEDRAZA, MARTA DE
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] This works aims to show the feasibility of using low-intensity ultrasound (US) to predict the salt content in brined Biceps femoris (BF) and Longissimus dorsi (LD) pork muscles. For this purpose, meat samples were salted in brine solution (20% w/w at 2 degrees C) for different times (24, 48, 96 and 168 h) and the US velocity measured before and after salting. In addition, model samples with preset water and salt contents were formulated and the US velocity was measured. In the model samples, the salt content (X-S) had a more marked effect on the US velocity (13.0 m/s per Delta X-S = 1% wet basis) than the water content (5.0 m/s per Delta X-w = 1% wet basis). The salt gain and the water loss during brining caused the US velocity to increase (61.5 and 49.3 m/s for 168 h in LD and BF, respectively). Significant linear relationships between the US velocity and both factors (X-S and X-w) were established (R-2 > 0.771). A predictive model of the salt content based on the US velocity was proposed; this was successfully validated (average estimation error 0.48%), which shows the feasibility of using US for industrial quality control purposes. (C) 2015 Elsevier Ltd. All rights reserved., This work was supported by the spanish Ministerio de Economia y Competitividad (MINECO) and Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) (contracts n. RTA2010-00029-004-01/02; RTA2013-00030-003-02), European Regional Development Fund (ERDF) and by the Universitat Politecnica de Valencia (UPV) through the FPI grant awarded to Marta de Prados.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic Characterisation of B.femoris from Iberian pigs of different genetics and feeding systems

  • Niñoles Rodenes, Laura
  • Ventanas, Sonia
  • Mulet Pons, Antonio|||0000-0001-6748-2663
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Ultrasonic velocity was used to characterise the differences in composition and texture of Biceps Femoris muscles from four batches of pigs of different genetics (Iberian and Iberian x Duroc) and feeding systems ("montanera" and concentrate). Significant differences (p<0.05) were found for the ultrasonic velocity in samples with different genetics and feeding systems. These differences were dependent on the temperature of the measurements and were related to the intramuscular fat content (IMF) of the samples and, therefore, to the meat quality. The ultrasonic velocities at 0 and 20 degrees C were related to the IMF (R=0.77 and 0.65, respectively). A discriminant analysis, including ultrasonic velocity at temperatures from 0 to 20 degrees C, allowed 87.0% of the samples to be correctly classified in the batches. Therefore, ultrasonics could be useful in the characterisation and differentiation of B. lemons muscles of Iberian pigs with different genetics and from different feeding systems. (C) 2011 Elsevier Ltd. All rights reserved, The authors acknowledge financial support from the "Ministerio de Educacion y Ciencia" in Spain (Projects RTA 2010-00029-004-02: CONSOLIDER - Ingenio 2010: CARNISENUSA (CSD2007-00016)) and the valuable advice of Professor Jesus Ventanas.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic characterization of pork fat crystallization during cold storage

  • Corona Jiménez, Edith
  • Santacatalina Bonet, Juan Vicente
  • Ventanas, Sonia
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] In this work, the feasibility of using ultrasonic velocity measurements for characterizing and differentiating the crystallization pattern in 2 pork backfats (Montanera and Cebo Iberian fats) during cold storage (0 degrees C, 2 degrees C, 5 degrees C, 7 degrees C, and 10 degrees C) was evaluated. The fatty acid profile, thermal behavior, and textural properties (hardness) of fat were also determined. Both fats became harder during cold storage (average hardness increase for both fats, 11.5 N, 8 N, and 1.8 N at 0, degrees C 2 degrees C, and 5 degrees C , respectively), showing a 2-step pattern related with the separate crystallization of the different existing triacylglycerols, which was well described using a modified Avrami equation (explained variance > 99%). Due to a greater content of saturated triacylglycerols, Cebo fat (45.1%) was harder than Montanera (41.8%). The ultrasonic velocity followed a similar 2-step pattern to hardness during cold storage, being found an average increase for both fats of 184, 161, and 150 m/s at 0 degrees C 2 degrees C, and 5 degrees C, respectively. Thus, ultrasonic measurements were useful both to characterize the textural changes taking place during cold storage and to differentiate between fats with different composition. Practical ApplicationThe cold storage of dry-cured meat products during their distribution and retail sale exert an important effect on their textural properties and consumers' acceptance due to the crystallization of the fat fraction, which is greatly influenced by the type of fat. In this work, a nondestructive ultrasonic technique was used to identify the textural changes provoked by the crystallization during cold storage, and to differentiate between fats, which could be used for quality control purposes., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad" in Spain (Project RTA 2010-00029-C04-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic assessment of textural changes in vacuum packaged sliced Iberian ham induced by high pressure treatment or cold storage

  • Corona Jiménez, Edith
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Mulet Pons, Antonio|||0000-0001-6748-2663
  • Benedito Fort, José Javier|||0000-0003-0163-4593
Ultrasonic measurements were used to characterize the effect of high pressure treatment (HPT) (600 MPa/6 min) or cold storage (6 °C/120 days) on the textural properties of vacuum packaged dry-cured ham. The ultrasonic velocity, textural properties and fat content were determined in the ham packages. The ultrasonic velocity was related to the ham hardness, which depends on the sample composition. HPT induced molecular alterations which resulted in an average increase in the hardness of lean tissue of 0.2 N and one of 0.3 N in that of fatty tissue. These textural changes give rise to a velocity increase (8 m/s for lean and 17 m/s for fatty tissue). The cold storage of the Iberian hamalso led to an increase in hardness (average 1.10 N) and ultrasonic velocity (average 70 m/s). Therefore, the non-destructive ultrasonic technique could be a reliable method with which to assess the textural changes induced by HPT or cold storage on packaged dry-cured ham., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad" in Spain (Project RTA 2010-00029-C04-02).