Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Accelerated mild heating of dry-cured ham by applying power ultrasound in a liquid medium

  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Bon Corbín, José|||0000-0002-0457-9705
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
[EN] Mild thermal treatments could be considered a feasible technique with which to improve the texture of dry-cured ham. This study explores the feasibility of using power ultrasound (PuS) to intensify heat transfer during the mild thermal treatment of dry-cured ham immersed in a liquid medium. For that purpose, a temperature controlled ultrasonic bath was used to avoid the water temperature rise due to cavitation during ultrasonic application, which could mask the actual effect of ultrasound in heat transport mechanisms. Experiments were carried out using dry-cured ham slices (thickness 2 cm), which were heated at different temperatures (40, 45, 50 degrees C) with (PuS) and without (conventional mechanical stirring, CV) ultrasonic assistance. Temperature was monitored in the two main muscles of the ham (Biceps lemons and Semimembranosus) and in different positions of the slice. A model that considered heat transfer entirely controlled by conduction was chosen for describing heating kinetics and quantify the influence of temperature and ultrasonic application in the apparent thermal diffusivity. The heat conduction model proposed was adequate to describe both CV and PuS heating kinetics (VAR > 98.6%). Ultrasound application sped up the heat transfer by increasing the apparent thermal diffusivity up to 51%, but the higher the temperature, the lower the ultrasonic intensification. The apparent thermal diffusivities identified for the slices were satisfactorily validated (VAR > 98.4%) in independent experiments with ham cylinders. Therefore, PuS could be considered as an effective technology for the purposes of accelerating the heat transfer, thus shortening the heating time of dry-cured ham slices immersed in a liquid medium., The authors acknowledge the financial support from the "Spanish Ministerio de Economia y Competitividad (MINECO), Instituto Nacional de Investigation y Tecnologia Agraria y Alimentaria (INIA)" in Spain, the European Regional Development Fund (ERDF 2014-2020) (Project RTA2013-00030-C03-02) and the PhD grant of M. Contreras from Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Non-invasive ultrasonic technology for continuous monitoring of pork loin and ham dry salting

  • PRADOS PEDRAZA, MARTA DE
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Online ultrasound measurements were taken using pulse-echo mode in loins (Longissimus dorsi) and hams at different salting times (up to 30 days). From the time-domain ultrasonic wave, the time of flight (TOF) was computed as well as its variation between two signals (Delta TOF). A progressive decrease in TOF during dry salting was found, which was linked to the salt gain, water loss and the reduction in sample thickness. Predictive models based on the ultrasonic parameters (Delta TOF and initial time of flight, TOF0) correctly classified 85% of the loins and 90% of the hams into 3 groups of salt content (low/medium/high): The results obtained confirm that the use of the ultrasonic pulse-echo technique is of great potential in the non-destructive monitoring of dry salting in pork loins and hams, as well as in the prediction of the salt gain for classification purposes. (C) 2017 Elsevier Ltd. All rights reserved., This work was supported by the Spanish Ministerio de Economia y Competitividad (MINECO), the Instituto Nacional de Investigation y Tecnologia Agraria y Alimentaria (INIA) and the European Regional Development Fund (ERDF 2014-2020) (contract n. RTA2013-00030-C03-02), by the PROMETEOII\2014\005 and by the Universitat Politecnica de Valencia (UPV) through the FPI grant awarded to Marta de Prados (SP-1.2011-S1-2757)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic Characterization and online monitoring of pork meat dry salting process

  • De Prados, M.
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Bearing in mind the highly variable salt content in dry-cured meat products with anatomical integrity, such as pork loin or ham, non-destructive salt content characterization and the online monitoring of dry salting are highly relevant for industrial purposes. This study explores the ability of low-intensity ultrasound to monitor the dry salting of pork Biceps femoris (BF) and Longissimus dorsi (LD) online, as well as to estimate the salt content, both in these muscles and in hams. For this purpose, meat samples were dry salted for up to 16 d at 2 C. During the salting of the muscles, the ultrasonic velocity was continuously measured at time intervals of 5 min, while in the hams it was measured before and after salting. The ultrasonic velocity increased progressively during the salting due to salt gain and water loss, reaching a velocity variation (DV) of 46.8 m/s after 16 d of dry salting for hams and 59.5 and 30.6 m/s after 48 h of dry salting for LD and BF, respectively. Accurate correlations between salt gain and DV were obtained (R2 ¿ 0.903 in LD-BF muscles and R2 ¿ 0.758 in hams), which allowed the assessment of the salt content with an average estimation error of 0.4% w.b. for both muscles and hams. Further research should investigate the use of the time of flight obtained through the pulse-echo mode, instead of the ultrasonic velocity, in order to improve the industrial applicabili, This work was supported by the Spanish Ministerio de Economia y Competitividad (MINECO), Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) and European Regional Development Fund (ERDF 2014-2020) (contract n. RTA2013-00030-C03-02), by the PROMETEOII\2014\005 and by the Universitat Politecnica de Valencia (UPV) through the FPI grant awarded to Marta de Prados (SP-1.2011-S1-2757).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ultrasonic online monitoring of the ham salting process. Methods for signal analysis: Time of flight calculation

  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • De Prados, M.
  • Martínez, G.
  • Gomez Alvarez-Arenas, T. E.
[EN] In the dry-cured ham industry, an accurate control of the dry-salting process is especially complex because of the great heterogeneity of the meat pieces and the effect of different operational variables. The main objective of this study was to evaluate the feasibility of using an ultrasound system and methodology, adapted to the industry requirements, for the online monitoring of the ham dry-salting process. For that purpose, hams were dry salted for different times (4, 10, 11, 14, 16 and 30 days) at 2 degrees C. The cushion zone of the ham was placed over the transducers during salting and ultrasonic signals were taken automatically (5 min interval by using pulse-echo mode. Several methods of signal analysis were considered in order to assess the time of flight (TOF). TOF estimations by means of the energy threshold and cross-correlation methods (between the initial ultrasonic signal and the remaining signals measured during salting and between consecutive signals 5 min apart without interpolation) were affected by the low signal-to-noise ratio and the pulse distortion and were discarded for the online monitoring of ham salting. Otherwise, the cross-correlation method between consecutive signals (5 min apart) with interpolation n = 3 (CCM-CS n = 3), between non-consecutive signals (1 h apart) (CCM-NCS) and the phase spectrum method (PSM), provided close estimations of the variation of the TOF, which correlated well with the ham salt gain (R-2 = 0.83 for CCM-CS n = 3, 0.93 for CCM-NCS and 0.90 for PSM). Consequently, the use of ultrasonic pulse-echo TOF measurements could be considered as a simple, non-invasive, non-destructive and reliable technique for the industrial monitoring of the ham dry-salting process., This work was supported by the Spanish Ministerio de Economia y Competitividad (MINECO), Institute Nacional de Investigacion y Tecnologia Agraria y Alimentaria and European Regional Development Fund (ERDF 2014-2020) (project RTA 2013-00030-C03-02), and by the Universitat Politecnica de Valencia through the FPI grant awarded to Marta de Prados (SP-1.2011-S1-2757).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Proteomic footprint of ultrasound intensification on sliced dry-cured ham subjected to mild thermal conditions

  • López-Pedrouso, M.
  • Pérez-Santaescolástica, C.
  • Franco, D.
  • Carballo, J.
  • Zapata, C.
  • Lorenzo, J. M.
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Ultrasound can intensify the heating process used to correct texture defects in dry-cured hams. The effect of ultrasound-assisted heating on the proteome of sliced dry-cured ham was evaluated. Dry-cured hams with high proteolysis index (PI > 36) were sliced, vacuum packed and subjected to conventional (CV) and ultrasound-assisted (US) thermal treatments. Comparative proteome profiling between sample groups was assessed by two-dimensional electrophoresis (2-DE) coupled to tandem mass spectrometry. It was found that protein fragmentation increased markedly after US thermal treatment. Specifically, fragments of the major myofibrillar protein, actin, were abundantly over-represented following US heating. In addition, five unfragmented sarcoplasmic proteins (i.e. fatty acid-binding protein, peroxiredoxin-6, superoxide dismutase, carbonyl reductase and aminoacylase) showed increased abundance in the US sample group. These results suggest candidate biomarkers to monitor proteolysis intensity and proteolysis-independent effects linked to cured ham quality by ultrasound application. Significance: The present proteome profiling study of treated dry-cured ham demonstrates the impact of ultrasound action on proteins. Moreover, negative organoleptic effects can be appearing with ultrasound treatment due to proteolysis increase. Therefore, the proteolysis monitoring could help to control these effects. In this regards, our results suggest that actin can be a candidate biomarker to monitor proteolysis intensity., This research was supported by Grant RTA 2013-00030-C03-03 from INIA (Spain). Acknowledgements to INIA for granting Cristina Perez Santaescolastica with a predoctoral scholarship (grant number CPD2015-0212). Jose M. Lorenzo is member of the MARCARNE network, funded by CYTED (ref. 116RT0503).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Application of temperature and ultrasound as corrective measures to decrease the adhesiveness in dry-cured ham. Influence on free amino acid and volatile compound profile

  • Pérez-Santaescolástica, C.
  • Carballo, J.
  • Fulladosa, E.
  • Lorenzo, J.M
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] The impact of low temperattire treatment and its combination with ultrasound has been evaluated in order to correct texture defects in dry-cured hams. A total of 26 dry-cured hams, classified as high proteolysis index (PI > 36%), were used. From these hams, ten slices from each ham sample were cut, vacuum packed and submitted to three different treatments: control (without treatment), conventional thermal treatments (CV) and thermal treatment assisted by power ultrasound (US). The impact of these treatments on instrumental adhesiveness, free amino acid and volatile compounds profile were assessed. Statistical analysis showed that both US and CV treatments, significantly (P<.001) decreased the instrumental adhesiveness of dry-cured hams from 85.27 g for CO to 40.59 and 38.68 g for US and CV groups, respectively. The total free amino acid content was significantly (P<.001) affected by both treatments, presenting higher values the samples from the US group (6691.5 vs. 6067.5 vs. 5278.2 mg/100 g dry matter for US, CV and CO groups, respectively). No significant differences were observed between US and CV treatments. All the individual free amino acids were influenced by ultrasound and temperature treatments, showing the highest content in sliced dry-cured ham submitted to ultrasounds at 50 degrees C, except for isoleucine which presented the highest level in samples from CV group. Similarly, significant differences (P<.05) were also detected in the total volatile compound content between CO and US groups, with a higher concentration in the CO batch (56,662.84 AU x 10(3)/g of dry-cured ham) than in the US treatment (45,848.47 AU x 10(3)/g of dry-cured ham), being the values in the CV treatment intermediate (48,497.25 AU x 10(3)/g of dry-cured ham). Aldehydes, ethers and esters, carboxylic acids and sulphur compounds were more abundant in the CO group, while CV group showed higher concentrations of ketones, alcohols and nitrogen compounds., This research was supported by Grant RTA 2013-00030-CO3-03 from INIA (Spain). Acknowledgements to INIA for granting Cristina Perez Santaescolastica with a predoctoral scholarship (grant number CPD2015-0212). Jose M. Lorenzo is member of the MARCARNE network, funded by CYTED (ref. 116RT0503).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Non-destructive salt content prediction in brined pork meat using ultrasound technology

  • PRADOS PEDRAZA, MARTA DE
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] This works aims to show the feasibility of using low-intensity ultrasound (US) to predict the salt content in brined Biceps femoris (BF) and Longissimus dorsi (LD) pork muscles. For this purpose, meat samples were salted in brine solution (20% w/w at 2 degrees C) for different times (24, 48, 96 and 168 h) and the US velocity measured before and after salting. In addition, model samples with preset water and salt contents were formulated and the US velocity was measured. In the model samples, the salt content (X-S) had a more marked effect on the US velocity (13.0 m/s per Delta X-S = 1% wet basis) than the water content (5.0 m/s per Delta X-w = 1% wet basis). The salt gain and the water loss during brining caused the US velocity to increase (61.5 and 49.3 m/s for 168 h in LD and BF, respectively). Significant linear relationships between the US velocity and both factors (X-S and X-w) were established (R-2 > 0.771). A predictive model of the salt content based on the US velocity was proposed; this was successfully validated (average estimation error 0.48%), which shows the feasibility of using US for industrial quality control purposes. (C) 2015 Elsevier Ltd. All rights reserved., This work was supported by the spanish Ministerio de Economia y Competitividad (MINECO) and Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) (contracts n. RTA2010-00029-004-01/02; RTA2013-00030-003-02), European Regional Development Fund (ERDF) and by the Universitat Politecnica de Valencia (UPV) through the FPI grant awarded to Marta de Prados.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Tesis doctoral (DoctoralThesis)

Use of ultrasound for the characterization and correction of textural defects in dry-cured ham

  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
[EN] Dry-cured ham is a product highly appreciated by consumers, nevertheless, there are a large number of manufacturing process-related parameters, as well as ham intrinsic factors, that compromise its final quality. One of the main problems in the quality of dry-cured ham is the appearance of textural defects, in particular, the development of pastiness. This defect is characterized by an excessive softness and loss of elastic behavior of the ham and when tasted, it provokes a feeling similar to the mouth-coating sensation produced by a flour-water paste during the mastication process. Pastiness also makes slicing difficult and promotes the adhesiveness between slices. Currently, the methods available to measure ham pastiness are time-consuming and destructive. For this reason, the seek of faster and non-destructive technologies capable of detecting pastiness is of great importance. In this sense, different technologies such as near infrared spectroscopy, X-rays or ultrasound, that have been previously tested for the nondestructive characterization of different meat products, could be of interest for the detection of ham pastiness. Different approaches, such as the use of high hydrostatic pressure (HHP) or the application of low-temperature long-time thermal treatments (LTLT) at the end of the ham manufacturing, have been previously addressed for the correction of pastiness in dry-cured ham. Notwithstanding, the high cost and the long time required for the HHP and LTLT treatments, respectively, highlights the need for moderate cost and faster alternatives. In this context, the main goals of this thesis were to determine the feasibility of using low intensity ultrasound to non-destructively detect the appearance of pastiness during ham manufacturing and to characterize the level of pastiness in the final product, as well as to explore the feasibility of mild ultrasonic assisted thermal treatments to correct this textural defect. To meet the goal of ham pastiness characterization and correction, a customized drycured ham manufacturing was designed and carried out in order to obtain hams with different levels of pastiness with no remarkable differences on the salt content. During ham manufacturing, the feasibility of using contact ultrasound to monitor the appearance of pastiness was addressed. The ultrasonic velocity was measured in the raw ham, at the end of the salting and post-salting stages, 3 times during the drying-maturation and once the manufacturing was finished. At the end of the manufacturing, the pastiness level (high, medium and no pasty) was also sensory evaluated by an expert panel. As the manufacturing progressed, a progressive increase in the ultrasonic velocity, from 1536 m/s in the raw ham to 1713 m/s in the final dry-cured ham, was found. Notwithstanding, the increase in the ultrasonic velocity was not related with the pastiness defect, probably because the ham texture changes linked to pastiness were masked by the great influence of the compositional changes (salt gain and moisture loss) on the ultrasonic velocity. Therefore, the ultrasonic velocity was not an effective parameter to detect the appearance of pastiness in hams during manufacturing, neither to classify them according to its pastiness level at the end of the manufacturing. Contact ultrasound was also used to monitor the compositional and textural changes taking place along the ham post-salting stage. For this purpose, another batch of hams was salted and post-salting times from 7 to 56 days were tested. During post-salting, the hams were weighted and the ultrasonic velocity was measured every 2 days. Each 7 post-salting days, the composition and the textural properties of a different ham were destructively analyzed. The ham weight loss during the post-salting stage was satisfactorily (r=0.95) described by the increase in the ultrasonic velocity. Moreover, the salt distribution and the moisture loss in the internal parts of the ham were satisfactorily related (r=0.93 and r=0.86, respectively) with the increase in the ultrasonic velocity. The variation in the ham hardness during post-salting was negligible and hence, the velocity increase was mainly attributed to the compositional changes, being barely affected by the changes in texture. The hams obtained after the customized manufacturing were sliced and the ultrasonic velocity and attenuation were measured on the Biceps femoris muscle with the aim of nondestructively finding out its pastiness level. Furthermore, in order to better analyze this textural defect, the composition, protein degradation, instrumental texture and microstructure of the hams were analyzed. Pasty samples presented the highest proteolysis index (38.7% compared to 33.1% for non-pasty hams), exhibited the more relevant structural degradation (merged myofibril structures and appearance of large gaps) and consequently, were the softest (5.4 N of hardness compared to 16.7 N for non-pasty hams) and presented the most intense viscous behavior (0.434 compared to 0.372 for non-pasty hams), although a high degree of experimental variability was found. The non-destructive assessment performed with ultrasound revealed that ultrasonic attenuation could be successfully applied for the grading of dry-cured ham slices according to its pastiness level. Thus, the greater the pastiness, the higher the ultrasonic attenuation, being the average attenuation coefficient for high, medium and no-pasty samples 48.2, 45.4 and 43.1 Np/m, respectively. Notwithstanding, the ultrasonic velocity was similar in all the ham samples, regardless its pastiness level. As observed in whole hams, the ultrasonic velocity was not a satisfactory parameter to detect pastiness in sliced ham, since the large influence of the composition on the ultrasonic velocity added to a similar salt and moisture content of the samples, regardless its pastiness level, led to a similar velocity for the different pastiness levels. Air-coupled ultrasonic techniques in both through-transmission and pulse-echo modes were developed for the characterization of dry-cured ham texture. The non-invasive nature of aircoupled ultrasound allows a contactless measurement, which makes easier its industrial implementation compared to conventional ultrasound techniques for high speed applications without material surface alteration and cross-contamination between food items. As for corrective actions of the texture defects in dry-cured ham, mild thermal treatments in two different heating media (water and air) were evaluated. Furthermore, the feasibility of intensifying these mild thermal treatments with the assistance of power ultrasound was considered. For that purpose, commercial vacuum-packed dry-cured ham slices were heated in a liquid medium, with and without ultrasonic assistance, at different temperatures (40, 45 and 50 ºC), measuring the temperature in the Biceps femoris and in the Semimembranosus muscles. Regarding the treatments in air, commercial vacuum-packed dry-cured ham cylinders were used. In the first set of experiments, ham was heated at a constant air velocity (2 m/s) until different temperatures (40, 45 and 50 ºC) were reached. While in the second set of experiments, ham was treated at constant air temperature (50 ºC) at different air velocities (1, 2, 3, 4 and 6 m/s). In both sets, the treatments were performed with and without power ultrasound application, measuring the temperature in the center of the cylinder. Thermal treatments were extended until a target temperature of 5 ºC lower than the medium (water-air) heating temperature was reached, thus, holding temperature stage did not exist and the treatments only considered the heating one. The heating kinetics of the ham treated in both water and air heating media were mathematically described by means of a heat conduction model. Once the heating finalized, the textural changes of ham (hardness and elastic behavior) were evaluated. The experiments showed that power ultrasound application sped up the heat transfer, significantly (p<0.05) shortening the heating time and increasing the apparent thermal diffusivity up to 51 and 37% for water and air heat treatments, respectively. For the thermal treatments using water, the increase in temperature during the heating brought about a lower ultrasonic intensification (the apparent thermal diffusivity was increased by 51% at 40 ºC compared to the 21% at 50 ºC). On the contrary, in experiments with air, the higher the temperature, the greater the ultrasonic enhancement (the apparent thermal diffusivity was increased by 5% at 40 ºC compared to the 38% at 50 ºC). The effect of the ultrasound application decreased as the air velocity increased, being minimal when the air velocity was the highest (the apparent thermal diffusivity was increased by 21% at 1 m/s compared to the 5% at 6 m/s). As regards the changes in the textural properties of ham after the mild thermal treatments at short times, an increase in hardness and elastic behavior was observed. Finally, the texture correction in dry-cured ham with different levels of pastiness was tackled. For this purpose, vacuum-packed dry-cured ham slices with high, medium and no pastiness were heated in a liquid medium at 40 and 50 ºC for a longer time (5 h, including heating and holding stages) than heating experiments, with and without the assistance of power ultrasound during the heating phase. The texture (hardness, elastic behavior and adhesiveness) and the microstructure of the ham was evaluated in both treated and control samples. After the mild thermal treatments, the texture of ham was improved since the hardness was increased (102%) and the viscous behavior diminished (11%). On average, the increase of hardness at 50 ºC was 159% higher than at 40 ºC, while the decrease of the viscous behavior was 13.5% larger at 50 ºC compared to 40 ºC. The ham adhesiveness was also enhanced independently of the treatment temperature, with a 55% reduction being observed. The application of power ultrasound during the heating phase did not involve any additional textural change. Likewise, after the thermal treatments, the microstructure of hams with pastiness notably changed, experiencing a severe shrinkage of the myofibrils, which contributed to explain the reported textural changes. In conclusion, pastiness is a relevant and highly complex textural defect in dry-cured ham. The use of contact ultrasound and the measurement of the ultrasonic attenuation could be considered a potential technology to non-destructively detect and characterize pastiness in sliced dry-cured ham. Future work should focus on extending this approach to identify pasty whole hams, considering for this purpose the use of air-coupled ultrasound. Moreover, the use of mild thermal treatments in liquid or gas media could be a feasible method to correct the defective texture of dry-cured hams and the application of power ultrasound during the heating phase could be a relevant means of speeding up the thermal treatments., [ES] El jamón curado es un producto muy apreciado por los consumidores, sin embargo, existen numerosos parámetros relacionados con el procesado, así como factores intrínsecos del jamón, que comprometen su calidad final. Uno de los principales problemas de calidad del jamón curado es la aparición de defectos de textura, concretamente, el desarrollo de pastosidad. Este defecto se caracteriza por una textura excesivamente blanda y un comportamiento menos elástico del jamón. A nivel sensorial, provoca una sensación de recubrimiento en boca similar a la masticación de una pasta de harina y agua. La pastosidad también dificulta el loncheado y promueve la adhesividad entre lonchas. Actualmente, los métodos disponibles para caracterizar la pastosidad requieren mucho tiempo y son destructivos. Por esta razón, la búsqueda de tecnologías más rápidas y no destructivas capaces de detectar la pastosidad es de gran importancia. En este sentido, distintas tecnologías como espectroscopía de infrarrojo cercano, rayos-X o ultrasonidos, que han sido ensayadas previamente para la caracterización no destructiva de diferentes productos cárnicos, podrían ser de interés para la detección de pastosidad en jamón. Diferentes alternativas, como el uso de altas presiones hidrostáticas (HHP) o la aplicación de tratamientos térmicos de larga duración a baja temperatura (LTLT) al final del proceso de elaboración del jamón, han sido abordadas previamente para la corrección de pastosidad en jamón curado. Sin embargo, el elevado coste y el largo tiempo requerido para los tratamientos HHP y LTLT, respectivamente, pone de manifiesto la necesidad de encontrar alternativas con un coste moderado y más rápidas. En este contexto, los principales objetivos de esta tesis fueron determinar la viabilidad de la utilización de ultrasonidos de baja intensidad para detectar de manera no destructiva la aparición de pastosidad durante el proceso de elaboración de jamón curado y caracterizar el nivel de pastosidad en el producto final, así como explorar la viabilidad de tratamientos térmicos moderados asistidos por ultrasonidos de alta intensidad para corregir dicho defecto de textura. Para cumplir el objetivo de caracterizar y corregir el defecto de pastosidad en jamón, se diseñó y se llevó a cabo un proceso de elaboración para obtener jamones con distintos niveles de pastosidad sin diferencias considerables del contenido en sal. Durante el procesado, se abordó la viabilidad de utilizar ultrasonidos por contacto para monitorizar la aparición de la pastosidad. Así, la velocidad ultrasónica se midió en el jamón fresco, al final de las etapas de salado y postsalado, 3 veces durante el secado-maduración y una vez terminado el proceso de elaboración. Al final del procesado, también se evaluó el nivel de pastosidad (alto, medio y sin pastosidad) en el jamón loncheado por un panel experto. A medida que avanzó el proceso de elaboración, se observó un aumento progresivo de la velocidad ultrasónica, de 1536 m/s en jamón fresco hasta 1713 m/s en jamón curado. Sin embargo, el aumento en la velocidad ultrasónica no se relacionó con el defecto de pastosidad, probablemente porque los cambios de textura del jamón vinculados con la pastosidad fueron enmascarados por la gran influencia de los cambios composicionales (ganancia de sal y pérdida de humedad) en la velocidad ultrasónica. Así, la velocidad ultrasónica no fue un parámetro útil para detectar la aparición de pastosidad en jamón durante su procesado ni para clasificar los jamones según su nivel de pastosidad al final del procesado. Los ultrasonidos por contacto también se utilizaron para monitorizar los cambios composicionales y texturales que tienen lugar a lo largo de la etapa de postsalado del jamón. Para ello, se saló otro lote de jamones y se evaluaron distintos tiempos de postsalado, desde 7 hasta 56 días. Durante el postsalado, los jamones se pesaron y se midió su velocidad ultrasónica cada 2 días. Cada 7 días de postsalado, se analizó destructivamente la composición y las propiedades texturales de un jamón. La pérdida de peso de los jamones durante la etapa de postsalado fue descrita satisfactoriamente (r=0.95) por el aumento de la velocidad ultrasónica. Además, la distribución de sal y la pérdida de humedad en el interior del jamón se relacionaron de forma satisfactoria (r=0.93 y r=0.86, respectivamente) con el aumento de la velocidad ultrasónica. La variación en la dureza del jamón durante el postsalado fue no significativa y, por ello, el aumento de la velocidad ultrasónica se atribuyó principalmente a los cambios de composición, siendo apenas afectada por los cambios de textura. Los jamones obtenidos con distintos niveles de pastosidad después del proceso de elaboración, se cortaron y se midió la velocidad y la atenuación ultrasónica del músculo Biceps femoris con el objetivo de averiguar de forma no destructiva su nivel de pastosidad. Además, con el fin de analizar mejor este defecto de textura, se analizaron el índice de proteólisis, la microestructura, la textura instrumental y la composición de los jamones. Las muestras pastosas presentaron el índice de proteólisis más alto (38.7% comparado con el 33.1% de los jamones no pastosos), mostraron la degradación estructural más relevante (estructuras miofibrilares fusionadas y aparición de grandes huecos) y, en consecuencia, fueron las más blandas (5.4 N de dureza en comparación con los 16.7 N de los jamones no pastosos) y presentaron el comportamiento viscoso más intenso (0.434 comparado con el 0.372 de los jamones no pastosos), aunque se encontró una gran variabilidad experimental. La evaluación no destructiva llevada a cabo mediante ultrasonidos reveló que la atenuación ultrasónica se podría aplicar con éxito para la clasificación de las lonchas de jamón curado según su nivel de pastosidad. Así, cuanto mayor fue la pastosidad, mayor fue la atenuación ultrasónica, siendo el coeficiente de atenuación promedio de las muestras con alta, media y sin pastosidad de 48.2, 45.4 y 43.1 Np/m, respectivamente. Sin embargo, la velocidad ultrasónica fue muy similar en todas las muestras de jamón, independientemente de su nivel de pastosidad. Como se observó en los jamones enteros, la velocidad ultrasónica no fue un parámetro útil para cuantificar el defecto de pastosidad en jamón loncheado, ya que la gran influencia de la composición en la velocidad ultrasónica sumada al contenido similar de sal y humedad de las muestras, independientemente de su nivel de pastosidad, dio lugar a una velocidad similar en todos los niveles de pastosidad. Se desarrollaron dos técnicas de ultrasonidos acoplados por aire, tanto en modo transmisión-recepción como en pulso-eco, para caracterizar la textura de jamón curado. El carácter no invasivo de los ultrasonidos acoplados por aire permite llevar a cabo medidas sin contacto, facilitando su aplicación a nivel industrial en comparación con las técnicas ultrasónicas convencionales, ya que pueden realizarse medidas a mayor velocidad, sin alterar la superficie del material y evitando la contaminación cruzada entre alimentos. En cuanto a las medidas de corrección de defectos texturales en jamón curado, se evaluaron tratamientos térmicos moderados en dos medios de calentamiento diferentes (agua y aire). Además, se consideró la viabilidad de intensificar dichos tratamientos mediante la aplicación de ultrasonidos de alta intensidad (o de potencia). Para ello, se calentaron lonchas de jamón curado comercial envasadas al vacío en medio líquido, con y sin la aplicación de ultrasonidos, a diferentes temperaturas (40, 45 y 50 ºC), midiendo la temperatura en los músculos Biceps femoris y Semimembranosus. Respecto a los tratamientos en aire, se utilizaron cilindros de jamón curado comercial envasado al vacío. En el primer set de experimentos, el jamón se calentó a velocidad de aire constante (2 m/s) a diferentes temperaturas (40, 45 y 50 ºC); mientras que, en el segundo experimento, el jamón se calentó a temperatura de aire constante (50 ºC) a distintas velocidades (1, 2, 3, 4 y 6 m/s). En los dos sets, los tratamientos se llevaron a cabo con y sin la aplicación de ultrasonidos de potencia, midiendo la temperatura en el centro del cilindro. Los tratamientos térmicos se prolongaron hasta alcanzar la temperatura objetivo, definida como 5 ºC por debajo de la temperatura del medio de calentamiento (agua o aire). Así, no se llevó a cabo una fase de mantenimiento de la temperatura y sólo se consideró la fase de calentamiento de los tratamientos térmicos. Las cinéticas de calentamiento del jamón tratado tanto en agua como en aire se describieron matemáticamente considerando que la transferencia de calor estuvo únicamente controlada por conducción. Una vez finalizado el calentamiento, se evaluaron los cambios texturales del jamón (dureza y comportamiento elástico). Los experimentos mostraron que la aplicación de ultrasonidos de potencia aceleró la transferencia de calor, reduciendo significativamente (p<0.05) el tiempo de calentamiento y aumentando la difusividad térmica aparente hasta un 51 y 37% en los tratamientos térmicos en agua y aire, respectivamente. En el caso de los tratamientos térmicos en agua, el aumento de la temperatura durante el calentamiento provocó una intensificación ultrasónica menor (la difusividad térmica aparente aumentó un 51% a 40 ºC comparado con el 21% a 50 ºC). Por el contrario, en las experiencias en aire, cuanto mayor fue la temperatura, más efectiva fue la aplicación de los ultrasonidos (la difusividad térmica aparente incrementó un 5% a 40 ºC comparado con el 38% a 50 ºC). El efecto de la aplicación de los ultrasonidos disminuyó con el aumento de la velocidad del aire, siendo mínimo con la velocidad de aire más alta ensayada (la difusividad térmica aparente aumentó un 21% a 1 m/s comparado con el 5% a 6 m/s). En cuanto a los cambios de las propiedades texturales del jamón después de los tratamientos térmicos moderados limitados a la fase de calentamiento, se observó un aumento en su dureza y en su comportamiento elástico. Por último, se abordó la corrección de textura en jamón curado con distintos niveles de pastosidad. Para ello, se calentaron lonchas de jamón con alta, media y sin pastosidad envasadas al vacío en medio líquido a 40 y 50 ºC durante tiempos más largos (5 h, incluyendo las fases de calentamiento y mantenimiento) que en las experiencias sólo de calentamiento, con y sin la aplicación de ultrasonidos de potencia únicamente durante la fase de calentamiento. La textura (dureza, comportamiento elástico y adhesividad) y la microestructura del jamón se evaluaron tanto en las muestras tratadas como en las control. Después de los tratamientos térmicos moderados, la textura del jamón se vio mejorada puesto que su dureza aumentó (102%) y su comportamiento viscoso disminuyó (11%). En promedio, el aumento de la dureza a 50 ºC fue un 159% mayor que a 40 ºC, mientras que la disminución del comportamiento viscoso fue un 13.5% mayor a 50 ºC que a 40 ºC. La adhesividad del jamón también se vio disminuida, independientemente de la temperatura de tratamiento, observándose una reducción media del 55%. La aplicación de ultrasonidos de potencia durante la fase de calentamiento no implicó ningún cambio textural adicional. Asimismo, después de los tratamientos térmicos, la microestructura de los jamones con alta pastosidad cambió notablemente, experimentando una severa contracción de las miofibrillas, lo cual contribuyó a explicar los cambios de textura mencionados. En conclusión, la pastosidad es un defecto textural relevante y muy complejo en jamón curado. El uso de ultrasonidos por contacto y la medida de la atenuación ultrasónica podría considerarse a nivel industrial para detectar y caracterizar de forma no destructiva la pastosidad en lonchas de jamón curado. Futuros trabajos deberían estar orientados a la aplicación de esta tecnología para la identificación de jamones pastosos enteros, considerando para ello el uso de ultrasonidos acoplados por aire. Además, el uso de tratamientos térmicos moderados en medio líquido o gaseoso podría ser un método viable para corregir la textura defectuosa de jamones curados y la aplicación de ultrasonidos de potencia durante la fase de calentamiento podría considerarse para acelerar los tratamientos térmicos., [CA] El pernil curat és un producte molt apreciat pels consumidors, no obstant això, existeixen nombrosos paràmetres relacionats amb el processament, així com factors intrínsecs del pernil, que comprometen la seua qualitat final. Un dels principals problemes de qualitat del pernil curat és l'aparició de defectes de textura, concretament, el desenvolupament de pastositat. Aquest defecte es caracteritza per una excessiva blanor i una pèrdua del comportament elàstic del pernil. A nivell sensorial, provoca una sensació de recobriment en boca similar a la masticació d'una pasta de farina i aigua. La pastositat també dificulta el tallat i promou l'adhesivitat entre rodanxes. Actualment, els mètodes disponibles per a mesurar la pastositat requereixen molt de temps i són destructius. Per aquesta raó, la cerca de tecnologies més ràpides i no destructives capaces de detectar la pastositat és de gran importància. En aquest sentit, diferents tecnologies com espectroscòpia d'infraroig pròxim, raigs-X o ultrasons, que han sigut assajades prèviament per a la caracterització no destructiva de diferents productes carnis, podrien ser d'interés per a la detecció de pastositat en pernil. Diferents alternatives, com l'ús d'altes pressions hidroestàtiques (HHP) o l'aplicació de tractaments tèrmics de llarga duració a baixa temperatura (LTLT) al final del procés d'elaboració del pernil, han sigut abordades prèviament per a la correcció de pastositat en pernil curat. No obstant això, l'elevat cost i el llarg temps requerit per als tractaments HHP i LTLT, respectivament, posa de manifest la necessitat de trobar alternatives amb un cost moderat i més ràpides. En aquest context, els principals objectius d'aquesta tesi van ser determinar la viabilitat de la utilització dels ultrasons de baixa intensità per a detectar de manera no destructiva l'aparició de pastositat durant el procés d’elaboració de pernil curat i caracteritzar el nivell de pastositat en el producte final, així com explorar la viabilitat de tractaments tèrmics moderats assistits per ultrasons d’alta intensitat per a corregir aquest defecte de textura. Per a complir l'objectiu de caracteritzar i corregir el defecte de pastositat en pernil, es va dissenyar i es va dur a terme un procés d'elaboració configurat per a obtindre pernils amb diferents nivells de pastositat sense diferències considerables del contingut en sal. Durant el processament, es va abordar la viabilitat d'utilitzar ultrasons per contacte per a monitorar l'aparició de pastositat. La velocitat ultrasònica es va mesurar en el pernil fresc, al final de les etapes de salat i postsalat, 3 vegades durant l'assecat-maduració i una vegada acabat el procés d'elaboració. Al final del processament, el nivell de pastositat (alta, mitjana i sense pastositat) també es va avaluar per un panell expert. A mesura que va avançar el procés d'elaboració, es va trobar un augment progressiu de la velocitat ultrasònica, anant des de 1536 m/s en pernil fresc fins a 1713 m/s en pernil curat. No obstant això, l'augment en la velocitat ultrasònica no es va relacionar amb el defecte de pastositat, probablement perquè els canvis de textura del pernil vinculats amb la pastositat van ser emmascarats per la gran influència dels canvis composicionals (guany de sal i pèrdua d'humitat) en la velocitat ultrasònica. Així, la velocitat ultrasònica no va ser un paràmetre efectiu per a detectar l'aparició de pastositat en pernil durant el seu processament ni per a classificar els pernils segons el seu nivell de pastositat al final del processament. Els ultrasons per contacte també es van utilitzar per a monitorar els canvis composicionals i texturals que tenen lloc al llarg de l'etapa de postsalat del pernil. Per a això, es va salar un altre lot de pernils i es van avaluar diferents temps de postsalat, des de 7 fins a 56 dies. Durant el postsalat, els pernils es van pesar i es va mesurar la seua velocitat ultrasònica cada 2 dies. Cada 7 dies de postsalat, es van analitzar destructivament la composició i les propietats texturals d'un pernil diferent. La pèrdua de pes dels pernils durant l'etapa de postsalat va ser descrita satisfactòriament (r=0.95) per l'augment de la velocitat ultrasònica. A més, la distribució de sal i la pèrdua d'humitat a l'interior del pernil es van relacionar de manera satisfactòria (r=0.93 i r=0.86, respectivament) amb l'augment de la velocitat ultrasònica. La variació en la duresa del pernil durant el postsalat va ser mínima i, per això, l'augment de la velocitat ultrasònica es va atribuir principalment als canvis de composició, sent a penes afectada pels canvis de textura. Els pernils obtinguts després del procés d'elaboració configurat per a obtindre pernils amb diferents nivells de pastositat, es van tallar i es va mesurar la velocitat i l'atenuació ultrasònica del múscul Biceps femoris amb l'objectiu d'esbrinar de forma no destructiva el seu nivell de pastositat. A més, amb la finalitat d'analitzar millor aquest defecte de textura, es van analitzar la composició, la degradació proteica, la textura instrumental i la microestructura dels pernils. Les mostres pastoses van presentar l'índex de proteòlisis més alt (38.7% comparat amb el 33.1% dels pernils no pastosos), van mostrar la degradació estructural més rellevant (estructures miofibrilars fusionades i aparició de grans buits) i, en conseqüència, van ser les més blanes (5.4 N de duresa en comparació amb els 16.7 N dels pernils no pastosos) i van presentar el comportament viscós més intens (0.434 comparat amb el 0.372 dels pernils no pastosos), encara que es va trobar una gran variabilitat experimental. L'avaluació no destructiva duta a terme mitjançant ultrasons va revelar que l'atenuació ultrasònica es podria aplicar amb èxit per a la classificació de les rodanxes de pernil curat segons el seu nivell de pastositat. Així, com més gran va ser la pastositat, major va ser l'atenuació ultrasònica, sent el coeficient d'atenuació mitjà de les mostres amb alta, mitjana i sense pastositat 48.2, 45.4 i 43.1 Np/m, respectivament. No obstant això, la velocitat ultrasònica va ser molt similar en totes les mostres de pernil, independentment del seu nivell de pastositat. Com es va observar en els pernils sencers, la velocitat ultrasònica no va ser un paràmetre satisfactori per a detectar el defecte de pastositat en pernil tallat a rodanxes, ja que la gran influència de la composició en la velocitat ultrasònica sumada al contingut similar de sal i humitat de les mostres, independentment del seu nivell de pastositat, va donar lloc a una velocitat similar en tots els nivells de pastositat. Es van desenvolupar dues tècniques d'ultrasons acoblats per aire, tant en manera transmissió-recepció com en pols-eco, per a caracteritzar la textura de pernil curat. El caràcter no invasiu dels ultrasons acoblats per aire permet dur a terme mesures sense contacte, facilitant la seua aplicació a nivell industrial en comparació amb les tècniques ultrasòniques convencionals, ja que poden realitzar-se mesures a major velocitat, sense alterar la superfície del material i evitant la contaminació creuada entre aliments. Quant a les mesures de correcció de defectes texturals en pernil curat, es van avaluar tractaments tèrmics moderats en dos medis de calfament diferents (aigua i aire). A més, es va considerar la viabilitat d'intensificar aquests tractaments mitjançant l'aplicació d'ultrasons de potència. Per a això, es van calfar rodanxes de pernil curat comercial envasades al buit en medi líquid, amb i sense l'aplicació d'ultrasons, a diferents temperatures (40, 45 i 50 °C), mesurant la temperatura en els músculs Biceps femoris i Semimembranosus. Respecte als tractaments en aire, es van utilitzar cilindres de pernil curat comercial envasat al buit. En el primer set d'experiments, el pernil es va calfar a velocitat d'aire constant (2 m/s) fins que es van aconseguir diferents temperatures (40, 45 i 50 °C). Mentre que, en el segon, el pernil es va calfar a temperatura d'aire constant (50 °C) a diferents velocitats (1, 2, 3, 4 i 6 m/s). En els dos sets, els tractaments es van dur a terme amb i sense l'aplicació d'ultrasons de potència, mesurant la temperatura en el centre del cilindre. Els tractaments tèrmics es van prolongar fins a aconseguir la temperatura objectiu, definida 5 °C per davall de la temperatura del medi de calfament (aigua o aire); així, no es va dur a terme una fase de manteniment de la temperatura i només es va considerar la fase de calfament dels tractaments tèrmics. Les cinètiques de calfament del pernil tractat tant en aigua com en aire es van descriure matemàticament mitjançant un model de conducció de calor. Una vegada finalitzat el calfament, es van avaluar els canvis texturals del pernil (duresa i comportament elàstic). Els experiments van mostrar que l'aplicació d'ultrasons de potència va accelerar la transferència de calor, reduint significativament (p<0.05) el temps de calfament i augmentant la difusivitat tèrmica aparent fins a un 51 i 37% en els tractaments tèrmics en aigua i aire, respectivament. En el cas dels tractaments tèrmics en aigua, l'augment de la temperatura durant el calfament va provocar una intensificació ultrasònica menor (la difusivitat tèrmica aparent va augmentar un 51% a 40 °C comparat amb el 21% a 50 °C). Per contra, en les experiències en aire, com més alta va ser la temperatura, més efectiva va ser l'aplicació dels ultrasons (la difusivitat tèrmica aparent va incrementar un 5% a 40 °C comparat amb el 38% a 50 °C). L'efecte de l'aplicació dels ultrasons va disminuir amb l'augment de la velocitat de l'aire, sent mínim amb la velocitat d'aire més alta assajada (la difusivitat tèrmica aparent va augmentar un 21% a 1 m/s comparat amb el 5% a 6 m/s). Quant als canvis de les propietats texturals del pernil després dels tractaments tèrmics moderats a temps curts, es va observar un augment en la seua duresa i en el seu comportament elàstic. Finalment, es va abordar la correcció de textura en pernil curat amb diferents nivells de pastositat. Per a això, es van calfar rodanxes de pernil amb alta, mitjana i sense pastositat envasades al buit en medi líquid a 40 i 50 °C durant temps més llargs (5 h, incloent les fases de calfament i manteniment) que en les experiències només de calfament, amb i sense l'aplicació d'ultrasons de potència durant la fase de calfament. La textura (duresa, comportament elàstic i adhesivitat) i la microestructura del pernil es van avaluar tant en les mostres tractades com en les control. Després dels tractaments tèrmics moderats, la textura del pernil es va veure millorada perquè la seua duresa va augmentar (102%) i el seu comportament viscós va disminuir (11%). En mitjana, l'augment de la duresa a 50 °C va ser un 159% major que a 40 °C, mentre que la disminució del comportament viscós va ser un 13.5% major a 50 °C que a 40 °C. L'adhesivitat del pernil també es va veure disminuïda, independentment de la temperatura de tractament, observant-se una reducció del 55%. L'aplicació d'ultrasons de potència durant la fase de calfament no va implicar cap canvi textural addicional. Així mateix, després dels tractaments tèrmics, la microestructura dels pernils amb alta pastositat va canviar notablement, experimentant una severa contracció de les miofibrilles, el que va contribuir a explicar els canvis de textura esmentats. En conclusió, la pastositat és un defecte de textura rellevant i molt complex en pernil curat. L'ús d'ultrasons per contacte i la mesura de l'atenuació ultrasònica podria considerar-se una tecnologia potencial per a detectar i caracteritzar de forma no destructiva la pastositat en rodanxes de pernil curat. Futurs treballs haurien d'estar orientats a l'aplicació d'aquesta tecnologia per a la identificació de pernils pastosos sencers, considerant per a això l'ús d'ultrasons acoblats per aire. A més, l'ús de tractaments tèrmics moderats en medi líquid o gasós podria ser un mètode viable per a corregir la textura defectuosa de pernils curats i l'aplicació d'ultrasons de potència durant la fase de calfament podria ser una forma rellevant d'accelerar els tractaments tèrmics., Gracias a la Universitat Politècnica de València por concederme la beca para realizar mis estudios de doctorado, así como a los proyectos de investigación en los que he participado (RTA2013-00030-C03-02 y RTA2017-00024-C04-03)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Texture characterization of dry-cured ham using multi energy X-ray analysis

  • Fulladosa, E.
  • Austrich, A.
  • Muñoz, I
  • Guerrero, L.
  • Lorenzo, J.M
  • Gou, P.
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Multi energy X-ray sensors are able to differentiate and quantify X-rays of different energies. In contrast to conventional sensors, which simply record the overall energy of the X-rays whatever the energy of x-rays is, multi energy sensors provides a spectrum of the X-rays energies, which may be differently attenuated. In this study, the feasibility of this technology to detect changes in dry-cured ham slices after inducing proteolysis was evaluated. Effect of salt and water contents on the attenuation was also studied. In addition, the classification of commercial samples according to their proteolysis index was assessed. Results showed a decrease of attenuation for increasing proteolysis induction times (p < 0.01) for all the regions of the spectrum (energy bands), but not with the same intensity, at any of the analysed acquisition conditions. Salt and water contents produced a significant (p < 0.01) effect on the attenuation. Influence of salt content was higher than that of water content, and both affected the prediction of the proteolysis index. Classification score of commercial samples exhibited a limited discrimination capacity, showing the need for more sophisticated data analysis. (C) 2018 Elsevier Ltd. All rights reserved., This work was partially supported by INIA (contract n. RTA201300030-0O3-01), Ministerio de Economia y Competitividad (PEJ2014-A34573) and CERCA programme from Generalitat de Catalunya.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of proteolysis index level on instrumental adhesiveness, free amino acids content and volatile compounds profile of dry-cured ham

  • Pérez-Santaescolástica, C.
  • Carballo, J.
  • Fulladosa, E.
  • Lorenzo, J.M.
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Benedito Fort, José Javier|||0000-0003-0163-4593
[EN] Defective textures in dry-cured ham are a common problem that causes important economic losses in the ham industry. An increase of proteolysis during the dry-cured ham processing may lead to high adhesiveness and consumer rejection of the product. Therefore, the influence of proteolysis index (PI) on instrumental adhesiveness, free amino acids and volatile profile of dry-cured ham was assessed. Two hundred Spanish dry-cured ham units were firstly classified according to their PI: low PI ( < 32%), medium PI (32-36%) and high PI ( > 36%). Instrumental adhesiveness was affected by PI, showing the lowest values in the batch with low PI. Significant differences (P < 0.05) among groups were found in six amino acids: serine, taurine, cysteine, methionine, isoleucine and leucine. The content of leucine, serine, methionine, and isoleucine significantly (P < 0.05) increased as the proteolysis index rose. However, taurine and cysteine content showed an opposite behaviour, reaching the highest values in the dry-cured hams with low PI. Significant differences (P < 0.001) in the total content of volatile compounds among ham groups were observed, with the highest concentration in the batch with low PI, and decreasing the concentration as the PI increased. Regarding the different chemical families of volatiles, the hydrocarbons (the main family), alcohols, aldehydes, ketones and acids were more abundant in the hams showing the lowest PI. Esters did not show significant differences among the three batches of hams studied. The present study demonstrated that, apart from the effect on the adhesiveness, an excessive proteolysis seems to be associated with negative effects on the taste and aroma of the dry-cured ham., This research was supported by Grant RTA 2013-00030-CO3-03 from INIA (Spain). Acknowledgements to INIA for granting Cristina Perez Santaescolastica with a predoctoral scholarship. Jose M. Lorenzo is member of the MARCARNE network, funded by CYTED (ref. 116RT0503).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Intensification of heat transfer during mild thermal treatment of dry-cured ham by using airborne ultrasound

  • Contreras-Ruiz, Marina|||0000-0002-5107-5702
  • Benedito Fort, José Javier|||0000-0003-0163-4593
  • Bon Corbín, José|||0000-0002-0457-9705
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
[EN] The application of power ultrasound (PuS) could be used as a novel technology with which to intensify thermal treatments using hot air. Mild thermal treatments have been applied to improve the soft texture of dry-cured ham caused by defective processing. In this regard, the aim of this study was to assess the kinetic intensification linked to the application of airborne PuS in the mild thermal treatment using hot air of dry-cured ham. For this purpose, vacuum packed cylindrical samples (2.52±0.11cm in diameter and 1.90±0.14cm in height) of dry-cured ham were heated using hot air at different temperatures (40, 45, 50°C) and air velocities (1, 2, 3, 4, 6m/s) with (22.3kHz, 50W) and without PuS application. Heat transfer was analyzed by considering that it was entirely controlled by conduction and the apparent thermal diffusivity was identified by fitting the model to the heating kinetics. The obtained results revealed that PuS application sped up the heat transfer, showing an increase in the apparent thermal diffusivity (up to 37%). The improvement in the apparent thermal diffusivity produced by PuS application was greater at high temperatures (50°C) but negligible at high air velocities (6m/s). Heating caused an increase in the hardness and elasticity of dry-cured ham, which would correct ham pastiness defects, while the influence of PuS on such textural parameters was negligible., The authors acknowledge financial support from the "Spanish Ministerio de Economia y Competitividad (MINECO), the Institute Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA)" in Spain, the European Regional Development Fund (ERDF 2014-2020) (Project RTA2013-00030-C03-02) and the PhD grant of M. Contreras from the Universitat Politecnica de Valencia (Ref 2447 FPI-Programe 1-2015).