Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 29
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High thermoelectric performance in Bi2-xPbxBa2Co2Oy promoted by directional growth and annealing

  • Madre, M.A.
  • Costa, F.M.
  • Ferreira, N.M.
  • Costa, S.I.R.
  • Rasekh, S.
  • Torres, M.A.
  • Diez, J.C.
  • Amaral, V.S.
  • Amaral, J.S.
  • Sotelo, A.
Bi2-xPbxBa2Co2Oy (x=0.0, 0.2, 0.4, and 0.6) misfit compounds were grown by the laser floating zone technique. Microstructural analysis has shown the formation of thermoelectric grains together with high amount of secondary phases. Thermoelectric grains orientation is increased until 0.4Pb, while further substitution drastically destroys the preferential grain orientation. Electrical resistivity is very low compared with the values obtained in sintered materials, spectacularly increasing power factor. Moreover, the performance of these materials was further improved subjecting the as-grown samples to a postannealing step due to the rise of thermoelectric phase content. These microstructural modifications led to a high decrease of electrical resistivity, improving power factor in around a factor two at room temperature, compared with the as-grown samples. Moreover, the low thermal conductivity of the textured annealed samples leads to a maximum estimated ZT value of 0.53 for the 0.2 Pb-doped samples, much higher than the reported in literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thermoelectric doping effect in Ca3Co4-xNixO9 ceramics

  • Constantinescu, G.
  • Rasekh, S.
  • Torres, M.A.
  • Bosque, P.
  • Madre, M.A.
  • Sotelo, A.
  • Diez, J.C.
Ca3Co4-xNixO9 (x=0.01, 0.03, and 0.05) polycrystalline thermoelectric ceramics have been prepared by the classical solid state method. As a result of the Ni addition an increase in porosity has been detected. Moreover, the presence of Ni has been related with the increase of Ca2Co3O6 secondary phase and the appearance of a new NiO-CoO solid solution. However, for the 0.01-Ni doped samples an improvement in the thermoelectric performances has been measured. This effect has been related with a decrease in the resistivity values and an increase in the Seebeck coefficient. The raise in the power factor for the 0.01-Ni doped samples, compared with the undoped ones, is between 10 and 25% at 50 and 800 °C respectively. Moreover, the maximum power at 800 °C, around 0.25 mW/K2.m, is significantly higher than the best results obtained in Ni doped samples reported previously in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Thermoelectrics

  • Madre, M.A.
  • Rasekh, S.
  • Torres, M.A.
  • Diez, J.C.
  • Sotelo, A.
Metallic Ag microsphere in a ceramic matrix Thermoelectricity is the direct solid-state conversion between thermal and electrical energy, without any moving parts, due to the well-known Seebeck effect. Currently, more than half of the energy produced ends up in the form of wasted heat: thermoelectric harvesting and energy conversion constitutes an solution to improve the energy efficiency of classical industrial and domestic energy transforming processes, through thermoelectric modules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of Ag additions on the Bi1.6Pb0.4Sr2Co1.8Ox thermoelectric properties

  • Diez, J.C.
  • Rasekh, Sh.
  • Constantinescu, G.
  • Torres, M.A.
  • Madre, M.A.
  • Sotelo, A.
Bi1.6Pb0.4Sr2Co1.8Ox thermoelectric ceramics with small Ag additions (0, 1, and 3 wt.%) have been successfully produced by a sol-gel method via nitrates. Microstructure has shown a reduction on the amount of secondary phases and an increase on the bulk density with increasing Ag contents. The microstructural evolution, as a function of Ag content, is confirmed with the electrical resistivity values which show an important decrease for the 3 wt.% Ag samples, leading to maximum power factor values of about 0.025 mW/K2.m at room temperature, which is about two times higher than the obtained for the Ag-free sintered samples. Se han preparado cerámicas termoeléctricas de composición Bi1.6Pb0.4Sr2Co1.8Ox con pequeñas adiciones de Ag (0, 1, y 3 % en peso) por medio de un método sol-gel a partir de los nitratos metálicos. La microestructura ha mostrado una reducción de la cantidad de fases secundarias y un aumento de la densidad del material al aumentar la cantidad de Ag. La evolución microestructural, en función del contenido de Ag, se ha confirmado con los valores de la resistividad eléctrica que muestra una reducción importante para las muestras con 3 % en peso de Ag, lo que lleva a alcanzar valores máximos del factor de potencia de alrededor de 0.025 mW/K2.m a temperatura ambiente, que es dos veces mayor que el obtenido para muestras sinterizadas sin Ag
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Long-term high-temperature stability of directionally grown [Bi2Ba2O4]p[CoO2] rods

  • Diez, J.C.
  • Madre, M.A.
  • Torres, M.A.
  • Rasekh, S.
  • Sotelo, A.
[Bi2Ba2O4]p[CoO2] thermoelectric ceramics have been successfully grown from the melt using the laser floating zone method, followed by a thermal treatment at 700°C under air between 0 and 1532 h. The microstructural, thermoelectric, and mechanical properties were evaluated as a function of the thermal treatment length. Microstructure has shown that as-grown samples are composed of thermoelectric grains, together with a relatively high amount of secondary phases. Thermal treatment decreased the number and amount of secondary phases, producing nearly single-phase samples after 384 h. Consequently, the thermoelectric properties evaluated through the power factor showed a slight increase with the thermal treatment length, mainly due to the decrease of electrical resistivity, while the Seebeck coefficient was nearly unchanged. On the other hand, flexural strength was practically constant after 24 h thermal treatment.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High thermoelectric performances of Bi–AE–Co–O compounds directionally growth from the melt; [Altas prestaciones termoeléctricas en compuestos Bi-AE-Co-O crecidos direccionalmente desde el fundido]

  • Diez, J.C.
  • Rasekh, S.
  • Madre, M.A.
  • Torres, M.A.
  • Sotelo, A.E.
Bi2AE2Co2Ox (AE = Ca, Sr, and Ba) thermoelectric compounds were grown from the melt by the laser floating zone technique. Microstructural analysis of as-grown samples has shown the formation of well-aligned thermoelectric grains together with a relative high amount of secondary phases. On the other hand, a short (24 h) thermal treatment (810 °C for Sr, 800 °C for Ca, and 750 °C for Ba) under air, raises of thermoelectric phase content through the recombination of the secondary ones. These microstructural modifications led to a large decrease of electrical resistivity, improving the power factor. These results have been compared with samples prepared by the conventional solid state method and with the best values reported in the literature. From these data, it is possible to deduce that the high thermoelectric characteristics obtained in these samples make them very attractive for practical applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Continuous-mode laser ablation at the solid-liquid interface of pelletized low-cost materials for the production of luminescent Silicon Carbide nanocrystals

  • Ortega-Liébana, M. C.
  • Hueso, J. L.
  • Arenal, R.
  • Lahoz, R.
  • De La Fuente, G.F.
  • Santamaría, J.
We report on the fabrication of silicon carbide (SiC) nanocrystals using a continuous scanning mode laser for the ablation of pelletized SiC microparticles. As a major advantage, we propose the in situ generation and collection of freestanding nanoparticles in an ethanol liquid medium and the use of cost-effective SiC targets in comparison with those commercially available or synthesized after multiple steps. The SiC NPs exhibit luminescent properties under UV exposure and excellent colloidal stability for extended periods of time. The influence of a more oxidizing solvent such as water is also evaluated as the collecting medium.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Improved thermoelectric performances in textured Bi1.6Pb0.4Ba2Co2Oy/Ag composites

  • Sotelo, A.
  • Rasekh, S.
  • Torres, M. A.
  • Bosque, P.
  • Madre, M. A.
  • Diez, J. C.
Bi1.6Pb0.4Ba2Co2Oy thermoelectric ceramics with small Ag additions (0, 1, 3, and 5 wt%) have been textured using the laser floating zone method. Microstructure has shown a slight decrease on the secondary phases content and a better grain alignment in Ag added samples. These microstructural features are reflected in the thermoelectric properties, which have shown a significant decrease of electrical resistivity, when the Ag content is raised. In spite of a corresponding decrease of Seebeck coefficient, all the Ag-containing samples possess higher Power Factor values than the Bi1.6Pb0.4Ba2Co2Oy ones. Moreover, the maximum Power Factor values (about 0.36 mW/K2.m at 650 °C) have been measured in Bi1.6Pb0.4Ba2Co2Oy+3 wt% Ag samples, which are the best results reported in this family of materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Improving bulk Ca3Co4O9 thermoelectric materials through Zr doping

  • Madre, M.A.
  • Rasekh, S.
  • Torres, M.A.
  • Diez, J.C.
  • Sotelo, A.
Ca3Co4-xZrxOy polycrystalline ceramics with small Zr substitution have been prepared through the classical solid-state method. X-ray diffraction data have shown that all samples are composed only of Ca3Co4O9 and Ca3Co2O6 phases. Moreover, by increasing Zr substitution up to 0.07, Ca3Co2O6 phase content is decreased. Density measurements have revealed that all samples are very similar, with values around 74% of the theoretical density. Electrical resistivity is decreased in Zr-doped samples, with respect to the pure samples, while Seebeck coefficient is unchanged. Both factors lead to power factor values around 0.33 mW K-2 m-1 at 800°C in 0.07 Zr-doped samples, which are about 65% higher than those obtained for the undoped samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Microstructural characterization and tribological behavior of Laser Furnace processed ceramic tiles

  • Rey-García, F.
  • Gutiérrez-Mora, F.
  • Borrel, C.J.
  • Estepa, L.C.
  • Angurel, L.A.
  • De La Fuente, G.F.
This paper presents, for the first time, the processing of commercial ceramic tiles by means of Laser Furnace (LF) technology and its influence on their microstructure and tribology. Commercial porcelain and white clay, partially fired ceramic tiles, were processed by this method in order to study the effect of the laser treatment and its potential to produce ceramic items on a large scale, under extreme surface temperature conditions. The microstructure and depth of the laser irradiated ceramic samples were studied by FESEM. EDX analyses were employed to study composition before and after the laser treatment. Surface roughness was determined using Confocal Microscopy, while hardness and tribological behavior were studied using Vickers indentations and a ball-on-flat apparatus, respectively.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of simultaneous K, and Yb substitution for Ca on the microstructural and thermoelectric characteristics of CaMnO3 ceramics

  • Sotelo, A.
  • Depriester, M.
  • Torres, M.A.
  • Sahraoui, A.H.
  • Madre, M.A.
  • Diez, J.C.
CaMnO3-based materials are very attractive among n-type thermoelectric oxides for high-temperature applications when they are appropriately doped. The main drawback of these materials is the cost associated to the necessary rare earth cations. This work aims decreasing the amount of these materials through a partial substitution of Ca2+ by an equimolar mixture of K+ and Yb3+, Ca1-x(K0.5Yb0.5)xMnO3, with x = 0.05, 0.10, 0.15, and 0.20. XRD studies have confirmed that the thermoelectric phase is the major one in all samples. Microstructure has shown the formation of large crystals, and an increasing porosity when the substitution is raised. This evolution has been confirmed through density measurements. Electrical resistivity has been drastically decreased for the 0.10 substituted samples, compared with the 0.05 ones, slightly increasing for higher substitution. On the other hand, absolute Seebeck coefficient and thermal conductivity are lower when the substitution is raised. The best ZT values have been achieved for the 0.10 substituted samples, which are around the typical reported in the literature for higher doping level. These results clearly point out to a decrease of the necessary rare earth dopant content to achieve similar performances in CaMnO3 ceramics, which is of the main economic significance for their industrial production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Continuous processing of Bi2Sr2CaCu2O8+d precursor powders

  • Laliena, C.
  • Amaveda, H.
  • Özçelik, B.
  • Martínez, E.
  • de la Fuente, G.F.
  • Angurel, L.A.
A continuous solid-state process inside a roller furnace has been used to fabricate Bi-2212 powders. These powders were synthesized for their use as precursors to obtain textured monoliths by laser induced directional solidification. A thermal cycle has been defined, which depends on the length of the furnace, the prefixed temperature profile and the velocity of the sample inside the furnace. Powder properties have been studied as a function of the number of processing cycles. Phase evolution has been analyzed using X-ray diffraction, while other relevant properties of the powders, including grain size distribution, thermal behavior and temperature dependence of the AC susceptibility, have also been measured. These properties have been compared with those of commercial powders and precursors prepared using a standard solid-state protocol. Textured samples using these continuous solid-state precursors exhibit superconducting properties comparable to those similarly processed but prepared from commercial powders.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhanced electrical and thermoelectric properties from textured Bi1.6Pb0.4Ba2Co2Oy/Ag composites

  • Madre, M. A.
  • Rasekh, Sh.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Sotelo, A.
Bi1.6Pb0.4Ba2Co2Oy/3 wt% Ag composites have been textured using the laser floating zone technique. Microstructural observations have shown the formation of relatively high amounts of secondary phases and cracks along the plate-like grains in the as-grown materials. In spite of these microstructural features, electrical properties have not been drastically decreased. Annealing of these as-grown rods has enhanced the grains connectivity, decreased the contents of the secondary phases, and healed the cracks, thereby increasing their electrical performances. It has been deduced that oxygen content in the thermoelectric phase has not been significantly modified through annealing, as demonstrated by the very similar Seebeck values at room temperature in the as-grown and annealed samples. As a consequence of the low electrical resistivity values in the annealed materials, they reached higher power factor values than the as-grown ones. The highest power factor at room temperature is in the range of those reported for single crystals, while at 650 °C, it is the highest reported in Bi–Ba–Co–O polycrystalline family so far.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

From nanosized precursors to high performance ceramics: the case of Bi2Ca2Co1.7Ox

  • Madre, M. A.
  • Rasekh, Sh.
  • Touati, K.
  • Salvador, C.
  • Depriester, M.
  • Torres, M. A.
  • Bosque, P.
  • Diez, J. C.
  • Sotelo, A.
Bi2Ca2Co1.7Ox thermoelectric ceramics were prepared by four different synthesis routes: coprecipitation with ammonium carbonate or oxalic acid, attrition milling, and solid state (as reference). Microstructure showed that coprecipitation and attrition milling produced sintered materials with less porosity and smaller particle sizes than the solid state ones. Thermoelectric properties reflect the microstructure, leading to materials with lower electrical resistivity and higher Seebeck coefficient, when compared with the solid state ones. In spite of an increase in thermal conductivity in these samples due to their lower porosity, the maximum estimated Figure-of-Merit is higher than in sintered materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Laser-induced coloration of ceramic tiles covered with magnetron sputtered precursor layers

  • Rico, V.J.
  • Lahoz, R.
  • Rey-García, F.
  • de Francisco, I.
  • Gil-Rostra, J.
  • Espinós, J.P.
  • de la Fuente, G.F.
  • González-Elipe, A.R.
This paper reports a new methodology for the coloring of glazed ceramic tiles consisting of the near infrared pulsed laser processing of copper containing oxide coatings prepared by magnetron sputtering. As a second approach, the employ for the same purpose of a novel laser furnace technique is also described. Changing the laser parameters and using the laser furnace to treat the tiles at high temperature during irradiation has resulted in a wide color palette. The optical characterization of the modified tiles by UV-Vis spectroscopy has been complemented with their microstructural and compositional analysis by Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Time Of Flight Secondary Ion Mass Spectrometry (TOF-SIMS). The chemical composition of the surface was obtained by X-ray Photoemission Spectroscopy (XPS) and its structure determined by X?ray diffraction (XRD). The chemical resistance was characterized by several tests following the norm ISO 10545-13. Color changes have been attributed to surface microstructural and chemical transformations that have been accounted for by simple models involving different ablation, melting, diffusion, and segregation/agglomeration phenomena depending on the laser treatments employed.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Composite Bi-2212/Ag Superconductors Grown by Laser Travelling Floating Zone at Low Rates

  • Diez, J.C.
  • Sotelo, A.
  • Rasekh, S.
  • Amaveda, H.
  • Torres, M.A.
  • Bosque, P.
  • Chocarro, C.
  • Madre, M.A.
Well-textured Bi2.02Sr2.02Ca0.98Cu1.99O x /2.9 wt % Ag composite samples have been grown by the laser floating zone at very low rates (1, 3, and 5 mm/h). The as-grown samples present superconducting behavior, as a result of being composed by long and well-textured Bi-2212 grains as major phase. After annealing, the samples do not dramatically increase their J C. This effect has been associated with the presence of long cracks along the ab planes of the superconducting grains. Even after annealing, the cracks have not been totally removed and, as a consequence, the critical current of the samples after the thermal treatment has only been improved in around 50 %, compared with the as-grown samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Decrease of electrical resistivity in Ca3Co4O9 thermoelectric ceramics by Ti doping

  • Torres, M.A.
  • Rasekh, Sh.
  • Bosque, P.
  • Constantinescu, G.
  • Madre, M.A.
  • Diez, J.C.
  • Sotelo, A.
Ca3Co4−xTixO9 polycrystalline thermoelectric ceramics with small amounts of Ti have been prepared by the classical solid state method. X-ray diffraction data have shown that Ca3Co4O9 is the major phase, with small amounts of the Ca3Co2O6 one. Moreover, they show that Ti has been incorporated into these two phases. Electrical resistivity decreases, compared with the values for undoped samples, until 0.03-Ti doped ones. Further Ti addition produces an increase of resistivity with respect to the 0.03 Ti doped samples. Seebeck coefficient does not appreciably change in all the measured temperature range, independently of Ti content. The improvement in electrical resistivity leads to about 55 % higher power factor values for the 0.03 Ti-doped samples than that obtained in the undoped ones. The maximum power factor at 800 °C, around 0.33 mW/K2 m, is slightly higher than the obtained in higher density samples, clearly indicating the good thermoelectric performances of these doped samples.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of Sr substitution for Ca on the Ca3Co4O 9 thermoelectric properties

  • Constantinescu, G.
  • Rasekh, Sh.
  • Torres, M.A.
  • Diez, J.C.
  • Madre, M.A.
  • Sotelo, A.
Ca3−xSrxCo4O9 polycrystalline thermoelectric ceramics with small amounts of Sr have been synthesized by the classical solid state method. Microstructural characterizations have shown that all the Sr has been incorporated into the Ca3Co4O9 and Ca3Co2O6 structures and no Sr-based secondary phases have been produced. Apparent density measurements have shown that samples slightly increase their density until 0.05 Sr content, decreasing for higher contents. Electrical resistivity decreases and Seebeck coefficient slightly raises when Sr content increases until 0.07 Sr addition. The improvement in both parameters leads to higher power factor values than the usually obtained in samples prepared by the conventional solid state routes and close to those obtained in textured materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Use of laser technology to produce high thermoelectric performances in Bi2Sr2Co1.8Ox

  • Rasekh, S.
  • Costa, F.M.
  • Ferreira, N.M.
  • Torres, M.A.
  • Madre, M.A.
  • Diez, J.C.
  • Sotelo, A.
Bi2Sr2Co1.8Ox bulk polycrystalline ceramics were prepared by conventional sintering of powders, obtained by polymer solution method and by directional growth using the laser floating zone technique. Microstructural analysis showed randomly oriented grains in the classical sintered materials, while in the laser-textured samples well oriented crystals with the c-axis nearly perpendicular to the growth direction were observed. A significant reduction on electrical resistivity, compared with the sintered materials, was observed due to the decrease on the secondary phases content. As a consequence, a raise on the power factor of about 2 and 5 times, compared with the classically sintered samples, was obtained for the as-grown and annealed laser-textured samples, respectively. The maximum power factor obtained at 650 °C in the annealed laser-textured samples (∼0.20 mW/K2 m) is much higher than the best value obtained in sinter–forged textured materials at the same temperature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of Secondary Annealing Process on Critical Current Density in Highly Textured Bi-2212 Superconducting System

  • Aksan, M. A.
  • Madre, M. A.
  • Rasekh, S.
  • Constantinescu, G.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, A.
  • Yakinci, M. E.
Bi-2212 samples prepared by a solid-state reaction technique have been grown from the melt using the laser floating zone method. After annealing the as-grown bars, the samples showed a good grain alignment and a high transport critical current density. Secondary annealing processes were performed on the annealed samples with the aim of producing Bi-2212 phase controlled decomposition. Hence, the Bi-2201 phase and the secondary phases, which act as effective pinning centers, were obtained with the secondary annealing process. After these thermal treatments, the transport critical current densities of samples significantly increased, when compared to the annealed ones. The maximum critical current density was achieved when the samples were subjected to secondary annealing at 680°C for 168 h with an improvement of ~80%, compared to the annealed ones. Moreover, it was found that magnetization of the secondarily annealed samples was also increased. The magnetic critical current densities in these secondary annealed samples were about 3 times higher than the values obtained for the annealed ones. These results clearly indicate that the secondary annealing processes lead to the formation of effective pinning centers in the bulk material.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of current polarity on BSCCO/Ag ceramics textured by electrically assisted laser floating zone

  • Costa, F.M.
  • Rasekh, S.
  • Ferreira, N.M.
  • Sotelo, A.
  • Diez, J.C.
  • Madre, M.A.
Bi-2212/Ag superconducting ceramics were grown using the electrically assisted laser floating zone (EALFZ) technique. The main goal was improving the superconducting properties by applying an electrical current through the sample during the solidification process. The effect of a 100 mA current intensities in two configurations were studied: (i) direct current (connecting the seed rod to the positive pole and the feed to the negative one) and (ii) reverse current (positive pole connected to the feed rod and negative to the seed one). The resulting textured cylindrical bars were annealed in order to obtain the superconducting phases. A strong correlation between current polarity, grain alignment and superconducting properties was observed. The rods grown under direct current exhibit higher critical current density (∼3000 A/cm2) than the ones grown under conventional method (∼2300 A/cm2) or under reverse current condition (∼35 A/cm2). The superior value obtained for the direct current results from a better grain alignment and fewer amount of second phases.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Decrease of Ca3Co4O9+δthermal conductivity by Yb-doping

  • Kiirat, G.
  • Aksan, M.A.
  • Rasekh, Sh.
  • Madre, M.A.
  • Diez, J.C.
  • Sotelo, A.
In this study, the effect of Yb-substitution on the structural, electrical and thermal transport properties of the Ca 3Co 4O 9 þ δ system has been investigated in the low temperature region (between 10 and 300 K). The resistivity of samples increases with raising the Yb-concentration in the system. All the samples show a metal-semiconductor transition below 85 K. In the analysis based on Strongly Correlated Fermi Liquid Model, an increased bandwidth and a reduced electronic correlation are found. It has also been found that the energy gap, E0, value also decreases with Yb substitution. The samples show positive thermoelectric power, indicating that dominant charge carriers are holes in all the samples. The thermoelectric power value decreases with Yb-substitution. From Mott equation, it is determined that the Fermi energy and hole concentration decrease in the Yb-susbtituted samples, compared to the undoped ones. Thermal conductivity, κ, is decreased in about 50% of the measured in undoped samples for the 0.01 and 0.03 Yb-doped samples at 300 K. Highest figure of merit, ZT, value is found to be 5.4 10 3 at 300 K for the unsubstituted sample and the ZT value decreases by the substitution.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Development of a new thermoelectric Bi2Ca2Co 1.7Ox + Ca3Co4O9 composite

  • Rasekh, Sh.
  • Ferreira, N.M.
  • Costa, F.M.
  • Constantinescu, G.
  • Madre, M.A.
  • Torres, M.A.
  • Diez, J.C.
  • Sotelo, A.
Bi2Ca 2Co 1.7Ox nominal composition ceramic rods were textured by the electrically assisted laser floating zone technique. A new composite formed by three phases, two of them with well-known thermoelectric properties, Bi 2Ca2Co 1.7Ox and Ca 3Co 4O 9, was obtained for the first time when the growth process was performed with a 300 mA applied current. Under these conditions the thermoelectric performances of this new composite reach values above the highest ones reported in the literature for polycrystalline Bi 2Ca2Co 1.7Ox materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of postannealing process on Bi2Sr2.1Ca 0.9Cu2O8+δ textured superconductors

  • Sotelo, A.
  • Madre, M.A.
  • Rasekh, S.
  • Constantinescu, G.
  • Torres, M.A.
  • Diez, J.C.
Bi-2212 samples prepared by the classical solid-state method have been grown from the melt using the Laser Floating Zone (LFZ) method. They have shown good grain alignment and transport critical current densities (J c ). After postannealing processes designed to produce the Bi-2212 phase controlled decomposition, J c values have been increased in an important manner. Maximum values have been achieved when samples were thermally treated at 680 °C for 168 h with improvements around 80 %, compared with the original textured samples. The results clearly indicate that postannealing processes, when adequately controlled, produce the formation of effective pinning centers which are responsible for the increase in the measured J c values.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Textured Pb-Doped Bi-2212 Superconductors for Current Limiters

  • Sotelo, A.
  • Rasekh, Sh.
  • Amaveda, H.
  • Bosque, P.
  • Torres, M.A.
  • Madre, M.A.
  • Diez, J.C.
Bi2−x Pb x Sr2CaCu2O y (x = 0.0, 0.3, 0.4, and 0.5) textured materials have been prepared by the laser floating zone technique. The E − I curves showed and increase of the slope of the normal to superconducting transition with Pb addition. The best values have been obtained for the 0.4 Pb-doped samples, around 16 at 77 K. In spite of this improvement, Pb addition decreased J C and T C in all cases. On the other hand, electrical characterization at lower temperatures has led to an impressive raise in the 0.4 Pb-doped samples, reaching n values around 31, and J C of about 3,000 A/cm 2, at 65 K. At the same time, the mechanical integrity of the vitreous precursor materials has been determined. All the obtained results clearly indicate that these precursors, when properly processed by the laser floating technique, are promising candidates for practical applications as current limiters.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

New promising Co-free thermoelectric ceramic based on Ba-Fe-oxide

  • Constantinescu,G.
  • Diez,J. C.
  • Rasekh,Sh
  • Madre,M. A.
  • Torres,M. A.
  • Sotelo,A.
Thermoelectric ceramics are based in a limited number of transition metal oxides (Co, Mn, Ni,…) which produce materials with high thermoelectric performances. Based on previously existing thermoelectric phases, the phase diagram equilibrium can help to design new thermoelectric ceramics based on other transition metals (for example, Fe). In this work, BaFeOx ceramics have been prepared by the classical solid state method using different sintering temperatures. The produced materials have shown promising thermoelectric properties when treatment temperatures are in the perovskite zone domain of the phase equilibrium diagram. In spite of the good values for the Seebeck coefficients, power factor is low due to the high resistivities measured in all cases.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Improvement of thermoelectric properties of Bi2Sr2Co1.8Ox through solution synthetic methods

  • Torres, M.A.
  • Sotelo, A.
  • Rasekh, Sh.
  • Serrano, I.
  • Constantinescu, G.
  • Madre, M.A.
  • Diez, J.C.
Several solution synthetic methods, sol-gel and a polymeric route, have been studied in order to obtain Bi2Sr2Co1.8Ox ceramics with improved thermoelectric properties, compared to the classical solid state reaction. The products obtained by these different methods have been compared using DTA-TGA, powder X-ray diffraction, scanning electron microscopy, and thermoelectric characterizations. All the samples obtained by solution synthesis show higher homogeneity and lower content of secondary phases. The main differences in thermoelectrical properties are due to the decrease of electrical resistivity in samples obtained by solution methods, compared with the solid state obtained samples. Between them, the decrease is especially high for those samples prepared by the polymer solution method. Therefore, the polymeric solution synthesis route is shown to yield a power factor four times higher than the obtained for the solid state and sol-gel methods at room temperature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Influence of Ca substitution by Mg on the Ca3Co 4O9 performances

  • Constantinescu, G.
  • Rasekh, S.H.
  • Torres, M.A.
  • Chocarro, C.
  • Díez, J.C.
  • Madre, M.A.
  • Sotelo, A.
Ca3-x Mgx Co4 O 9 polycrystalline thermoelectric ceramics with small amounts of Mg have been synthesized by the classical solid state method. Microstructural characterizations have shown that all the Mg has been incorporated into the Ca 3 Co4 O 9 structure and no Mg-based secondary phases have been identified. Apparent density measurements have shown that samples do not modify their density until 0.05 Mg content, decreasing for higher contents. Electrical resistivity decreases and Seebeck coefficient slightly raises when Mg content increases until 0.05 Mg addition. The improvement in both parameters leads to higher power factor values than the usually obtained in samples prepared by the conventional solid state routes and close to those obtained in textured materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhancement of mechanical and thermoelectric properties of Ca3Co4O9 by Ag addition

  • Kahraman, F.
  • Madre, M. A.
  • Rasekh, S.
  • Salvador, C.
  • Bosque, P.
  • Torres, M. A.
  • Diez, J. C.
  • Sotelo, A.
Ca3Co4O9+x wt.% Ag (x=0, 1, 3, 5, and 10) polycrystalline thermoelectric ceramics have been prepared by a sol-gel route via nitrates followed by high temperature treatment before sintering. Out-of-plane XRD data have shown that major phase is the Ca3Co4O9 one, accompanied by metallic Ag. SEM observations have agreed with the XRD data. Apparent density measurements have revealed that all samples possess densities ranging between 80% and 90% when Ag content is raised. Mechanical properties have shown a drastic increase of bending stress when Ag is added to the samples. Electrical resistivity decreases with the Ag content, compared with the pure ones, while Seebeck coefficient slightly decreases. Maximum power factor values around 0.43mW/K2m at 800°C have been achieved for the 10wt.% Ag samples which is much higher than the measured in the pure Ca3Co4O9 samples.