Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Optical Tuning of Nanospheres Through Phase Transition: An Optical Nanocircuit Analysis

  • Cuadrado, Alexander
  • Toudert, Johan
  • García Cámara, Braulio
  • Vergaz Benito, Ricardo
  • González Benito, Francisco Javier
  • Alda, Javier
  • Serna, Rosalía
Plasmonic nanostructures can be described by equivalent impedance, allowing the analysis of their properties and performance by an RLC circuit equivalent model. In this letter, the equivalent impedance has been obtained from a power budget calculation that considers the dielectric functions of the matrix and the nanostructured material, the nanostructure geometry (in this case, spheres), the light wavelength, and its polarization. When Bi or Ga nanospheres are considered, the equivalent circuit undergoes a switching from a capacitive to and inductive response when the materials change their phase from solid to liquid. Finally, this approach is applied to the design of reconfigurable metamaterials., This work was supported by the Ministerio de Economía y Competitividad of Spain, project 32 of CEMIE-Solar from Secretara de Energía-Sustentabilidad Energética and the Terahertz Science and Technology National Lab from CONACYT (México) under Grant TEC2012-38901-C02-01, Grant TEC2015-69916-C2-1-R, Explora Grant TEC2013-50138-EXP, Grant TEC2013-40442, and Grant PR2015-00063., Publicado
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Modeling of the refractive index and composition of luminescent nanometric chlorinated-silicon nitride films with embedded Si-quantum dots

  • Rodríguez-Gómez, A.
  • Escobar-Alarcón, L.
  • Serna, Rosalía
  • Cabello, Fátima
  • Haro-Poniatowski, E.
  • García-Valenzuela, A.
  • Alonso, J.C.
6 págs.; 9 figs.; 3 tabs., The refractive index of nanometric (<100 nm) chlorinated-silicon nitride films with embedded silicon quantum dots, prepared by remote plasma enhanced chemical vapor deposition was investigated by spectroscopic ellipsometry. The complex refractive indexes and thicknesses of the films were obtained from the ellipsometric measurements using the Cauchy model. The chemical composition of the bulk of the films, including the hydrogen, chlorine, and oxygen content, was measured by elastic forward analysis (EFA) and X-ray photoelectron spectroscopy (XPS). The EFA and XPS results indicate that the films are composed of nearly stoichiometric silicon nitride (SiN) with different amounts of hydrogen, chlorine, and oxygen, and that their top surface is oxidized. Based on the composition results the refractive index of the films was fitted using the effective medium approximation considering the system: Si substrate + SiN + Si + voids + top ultrathin oxidized surface layer. Published by AIP Publishing, This research work was partially supported under Project PAPIIT-UNAM No. IG100614-2. We also acknowledge the funding from the Spanish Ministry for Economy and Competitiveness through TEC 2012-38901- C02-01 and TEC 2015-69916-C2-1-R projects., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polaritonic-to-Plasmonic Transition in Optically Resonant Bismuth Nanospheres for High-Contrast Switchable Ultraviolet Meta-Filters

  • Cuadrado, A.
  • Toudert, Johann
  • Serna, Rosalía
12 págs.; 4 figs., In the quest to unveil alternative plasmonic elements overcoming noble metals for selected applications in photonics, we investigate, by numerical simulations, the near ultraviolet (UV)-to-near infrared optical response of solid and liquid Bi nanospheres embedded in a dielectric matrix. We also determine the resulting transmission contrast upon reversible solid-liquid phase transition to evaluate their potential for switchable optical filtering. The optical response of the solid (liquid) Bi nanospheres is ruled by localized polaritonic (plasmonic) resonances tunable by controlling the diameter. For a selected diameter between 20 and 50 nm, both solid and liquid nanospheres present a dipolar resonance, inducing a strong peak extinction in the near UV, however, at different photon energies. This enables a high transmission contrast at selected near UV photon energies. It is estimated that a 2-D assembly of 30-nm solid Bi nanospheres with a surface coverage of 32% will almost totally render extinct (transmission of 2%) a near UV 3.45-eV (359 nm) light beam, whereas upon phase transition, the resulting liquid Bi nanospheres will show a transmission of 30%. This paper is appealing for the fabrication of locally reconfigurable optical metamaterials for integrated switchable near-UV optics. Ó 2016 IEEE, This work was supported in part by the European Community Seventh Framework Programme (FP7-NMP-2010-EU-MEXICO) under Grant 263878 and in part by the Spanish Ministry for Economy and Competitiveness under Project TEC2012-38901-C02-01 and Project TEC2015-69916-C2-1-R., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultraviolet-visible interband plasmonics with p-block elements

  • Toudert, Johann
  • Serna, Rosalía
14 págs.; 4 figs. ; OCIS codes: (160.0160) Materials; (160.4760) Optical properties; (250.5403) Plasmonics; (260.5740) Resonance; (240.5420) Polaritons; (300.0300) Spectroscopy, We investigate the origin of the ultraviolet - visible plasmonic properties of three elemental materials from the p-block: Bi, Sb and Ga, which has not been discussed so far despite growing interest in these materials for plasmonic applications. We review and analyze a broad range of optically-determined dielectric functions ε = ε + jε of these elemental materials available in the literature, covering a wide photon energy range (from 0.03 to 24 eV). It is shown that the contribution of free carriers to ε in the ultraviolet - visible is negligible for Bi and Sb and small for Ga. In contrast, the interband transitions of these elemental materials show a high oscillator strength that yields a strong negative contribution to ε in the ultraviolet - visible. Therefore it is proposed that, in nanostructures made of these elemental materials, the interband transitions induce localized surface plasmon-like resonances in the ultraviolet - visible. It is exemplified how these resonances are sensitive to the size and environment of the nanostructures. Furthermore, ultraviolet - visible plasmonic properties achieved through interband transitions, without free carrier excitation, are especially appealing because they might be tuned through the tailoring of the band structure and by the occupancy of electronic states. Therefore they are promising for the development of broadly tunable nanostructures and metamaterials. ©2016 Optical Society of America, We acknowledge the Spanish Ministry for Economy and Competitiveness (Projects TEC 2012-38901-C02-01 and TEC2015-69916-C2-1-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation and broadband white emission of Eu-doped thin films based on SiAlON

  • Camps, I.
  • Mariscal, A.
  • Serna, Rosalía
5 pags., 4 figs., The optical performance of europium (Eu) doped SiAlON thin films and its preparation by pulsed laser deposition are studied. The undoped SiAlON films show a high refractive index (2.34) close to that of silicon nitride. After doping with Eu the oxygen content increases in the films and leads to the formation of an oxynitride with a refractive index of 1.87 and excellent transparency in the visible-near infrared. Upon excitation at 355 nm the films show a broad band (FWHM of 200 nm) emission in the visible range (400¿750 nm) that is associated to the emission of the Eu in the 2+ oxidation state. Enhancement of the emission together with a blue spectral shift has been found when the films are annealed at low temperature (600 °C). These films show promising properties for the development of Si compatible thin films integrated emitters. & 2016 Elsevier B.V., This work was partially funded by MINECO TEC2012-38901- C02-01 and MINECO /FEDER TEC2015-69916-C2-1-R. We ac- knowledge the work of N.P.B,E.A.andL.C.A.(IPFN,Portugal) for their help with the RBS analysis., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unveiling the far infrared-to-ultraviolet optical properties of bismuth for applications in plasmonics and nanophotonics

  • Toudert, Johann
  • Serna, Rosalía
  • Camps, I.
  • Wojcik, J.
  • Mascher, P.
  • Rebollar, Esther
  • Ezquerra, Tiberio A.
11 pags., 6 figs., For years bismuth (Bi) has appealed to a broad community of scientists due to its peculiar electronic, optical, and more recently plasmonic and photocatalytic properties, which enable both the understanding of basic science phenomena and the development of a wide range of applications. In spite of this interest, a comprehensive spectral analysis of the dielectric function (¿ = ¿1 + j¿2) of bulk Bi from the far infrared (IR) to the ultraviolet (UV) region is not available. So far, the data have been reported in limited spectral ranges and show a wide dispersion that is especially notorious for the IR region. In this work we report ¿ for Bi in a wide spectral range from 0.05 to 4.7 eV (24.8 to 0.3 ¿m, far IR to UV). ¿ is extracted from spectroscopic ellipsometry measurements of excellent quality (dense and smooth) Bi films by using the transfer matrix formalism and Kramers¿Kronig consistent analysis. The higher quality and accuracy of the obtained ¿ compared with the literature data is demonstrated. The analysis and use of this reference bulk dielectric function provides crucial information for the exploration and understanding of the optical, plasmonic, and photocatalytic properties of Bi nanostructures. From its analysis, it is evidenced that the optical properties of Bi in the mid wave IR-to-UV are driven only by interband transitions, which are responsible for the dominant absorption band peaking at about 0.8 eV. Therefore, the plasmonic behavior and the photocatalytic performance of Bi nanostructures in the visible and UV are likely driven by these interband transitions that make ¿1 turn negative in this region without the need of exciting free carriers. Furthermore, classical electrodynamic simulations using the obtained ¿ show a strong size dependence for the optical extinction of Bi nanospheres in the far IR-to-near IR with Mie-like resonances broadly tunable across this region., This research received funding from the European Community Seven Framework Programme (FP7-NMP-2010-EU-MEXICO) under Grant Agreement No. 263878. We also acknowledge funding from the Spanish Ministry for Economy and Competitiveness through and TEC2012-38901-C02-01 and TEC 2015-69916-C2-1-R projects. E.R. acknowledges funding from the Spanish Ministry for Economy and Competitiveness through a Ramón y Cajal Fellowship (RYC-2011-08069). In Canada, this work was supported by the Discovery Grants program of the Natural Science and Engineering Research Council (NSERC)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Interband transitions in semi-metals, semiconductors, and topological insulators: a new driving force for plasmonics and nanophotonics

  • Toudert, Johann
  • Serna, Rosalía
27 pags., 10 figs. -- OCIS codes: (160.4760) Optical properties; (160.6000) Semiconductor materials; (160.4236) Nanomaterials; (050.6624) Subwavelength structures; (250.5403) Plasmonics; (350.4238) Nanophotonics and photonic crystals., Plasmonic and dielectric Mie resonances in subwavelength nanostructures provide an efficient way to manipulate light below the diffraction limit that has fostered the growth of plasmonics and nanophotonics. Plasmonic resonances have been mainly related with the excitation of free charge carriers, initially in metals, and dielectric Mie resonances have been identified in Si nanostructures. Remarkably, although much less studied, semi-metals, semiconductors and topological insulators of the p-block enable plasmonic resonances without free charge carriers and dielectric Mie resonances with enhanced properties compared with Si. In this review, we explain how interband transitions in these materials show a major role in this duality. We evaluate the plasmonic and Mie performance of nanostructures made of relevant p-block elements and compounds, especially Bi, and discuss their promising potential for applications ranging from switchable plasmonics and nanophotonics to energy conversion, especially photocatalysis., European Community Seventh Framework Programme (FP7-NMP-2010-EUMEXICO) (263878); Spanish Ministry for Economy and Competitiveness (TEC 2012-38901-C02-01 and TEC 2015-69916-C2-1-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2ZnSnS4 bulk poly-crystals

  • Levcenko, S.
  • Hajdeu-Chicarosh, E.
  • García-Llamas, E.
  • Caballero, Raquel
  • Serna, Rosalía
  • Bodnar, I. V.
  • Victorov, I. A.
  • Guc, M.
  • Merino, J. M.
  • Pérez-Rodríguez, A.
  • Arushanov, E.
  • León, M.
5 pags., 3 figs., 3 tabs., The linear optical properties of Cu2ZnSnS4 bulk poly-crystals have been investigated using spectroscopic ellipsometry in the range of 1.2–4.6 eV at room temperature. The characteristic features identified in the optical spectra are explained by using the Adachi analytical model for the interband transitions at the corresponding critical points in the Brillouin zone. The experimental data have been modeled over the entire spectral range taking into account the lowest E0 transition near the fundamental absorption edge and E1A and E1B higher energy interband transitions. In addition, the spectral dependences of the refractive index, extinction coefficient, absorption coefficient, and normal-incidence reflectivity values have been accurately determined and are provided since they are essential data for the design of Cu2ZnSnS4 based optoelectronic devices. Published by AIP Publishing., The research leading to the presented results was partially supported by the European Project INFINITE-CELL (Ref. H2020-MSCA-RISE-2017-777968, 2017–2021, www.infinitecell. eu) and the Spanish MINECO Projects “WINCOST” (ENE2016-80788-C5-2-R) and PHOTOMANA (TEC2015- 69916-C2-1-R). The authors from the Institute of Applied Physics appreciate the financial support from STCU 6224 and from the Institutional Project No. CSSDT 15.817.02.04A, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis of transparent Er-doped fluorotellurite glass-ceramics through controlled crystallization

  • Morea, Roberta
  • Teddy Fernandez, Toney
  • Fernández, Joaquín
  • Balda, Rolindes
  • Gonzalo de los Reyes, J.
This work presents a detailed study of the preparation and microstructure of transparent glass-ceramics obtained from a TeO2-ZnO-ZnF2 fluorotellurite glass doped with ErF3. The determination of nucleation and crystal growth rate-like curves allows establishing a narrow temperature range (340-350°C) for a controlled crystal- lization. Thereafter, a crystalline phase was grown through a two-step heat treatment: 10-20 h at a temperature slightly above the glass transition temperature, followed by a 2.5-3 h treatment at 340°C. Structural analysis showed the nucleation of ErF3 nanocrystals (NCs) with a typical size of ≈50 nm that were homogeneously distributed in the glass matrix. The resulting glass-ceramic material remains highly transparent, with a small crystalline to amorphous ratio; yet the presence of ErF3 NCs has a large impact on the photoluminescence response of Er3+ ions. Upconverted visible emission is analyzed under 980 nm excitation: red emission from the 4F9/2 level is dramatically enhanced with respect to green 2H11/2, 4S3/2 → 4I15/2 hypersensitive transitions. The observed behaviour is attributed to the presence of Er3+ ions in the NCs, which are sites with lower phonon energy than the glass matrix. Moreover, the shorter interionic distance between Er3+ ions in the NCs eases energy transfer between them., This work has been supported by the Spanish Ministry of Economy & Competitivity (Projects MAT 2013-48246- C2-2-P, TEC 2012-38901-C02-01, and TEC 2015-69916-C2-1-R) and the Basque Country Government (Project IT-943-16). R. Morea acknowledges a FPI grant from the Spanish Government., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Europium monoxide nanocrystalline thin films with high near-infrared transparency

  • Mariscal, A.
  • Quesada, Adrián
  • Tarazaga Martín-Luengo, Aitana
  • García García-Tuñón, Miguel Ángel
  • Bonanni, A.
  • Fernández Lozano, José Francisco
  • Serna, Rosalía
5 pags., 3 figs., Nanocrystalline textured EuO thin films are prepared by an oxygen loss process from a pure EuO bulk ceramic target through pulsed laser deposition in vacuum at room temperature. X-ray diffraction spectra evidence a well-defined diffraction peak corresponding to the EuO phase textured along the (1 1 0) direction. Analysis of the XRD peak profile indicates that the films are nanocrystalline (average crystallite size of 11 nm) with a compressive residual strain. The formation of stoichiometric EuO is further confirmed by a strong signal from Eu in the X-ray photoelectron spectra. The complex refractive index in the near infrared has been determined by spectroscopic ellipsometry and shows that the EuO films have a high transparency (k < 10) and a refractive index of 2.1. A band-gap shift of 0.25 eV is found with respect to the EuO bulk. These films, deposited by an accessible and efficient method, open a new route to produce EuO films with optical quality, suitable for NIR optoelectronic components., This work has been financially supported by the Spanish Ministry of Economy and Competitiveness through the projects MINECO/FEDER TEC2015-69916-C2-1-R, MAT2013-47878-C2-1-R and MAT2013-48009-C4-1-P co-funded with FEDER funds. Support by the EC’s Horizon2020 Research and Innovation Programme (grant 645776), by the Austrian Science Fund – FWF (P24471 and P26830), and by the NATO Science for Peace Programme (grant 984735) is acknowledged. A.M. acknowledges the financial support through BES-2013-062593., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Evidencing early pyrochlore formation in rare-earth doped TiO2 nanocrystals: Structure sensing via VIS and NIR Er3+ light emission

  • Camps, I.
  • Borlaf, Mario
  • Toudert, Johann
  • Andrés, Alicia de
  • Colomer, María T.
  • Moreno, Rodrigo
  • Serna, Rosalía
8 pags., 6 figs., Er doping of TiO colloidal nanocrystals enhances their performance for photo-induced applications. Such doping is known to delay the anatase to rutile transformation under thermal treatment; nonetheless relevant information on the Er light emission and location within the TiO structures is still incomplete. Er photoluminescence emission both in the visible (upconverted) and infrared photoluminescence is used for the first time to probe the ions location within the different TiO structures. The results show that Er ions in the as-prepared xerogels are not embedded in the anatase crystallites, and only upon thermal treatment Er diffusion is induced into crystal interstitial positions to form a solid solution. At higher temperatures rutile is formed inducing Er segregation and giving rise to the formation of pyrochlore (ErTiO), as shown by a distinct emission in the infrared spectrum due to the Er ions located within the pyrochlore compound. Although pyrochlore is usually a high temperature phase, analysis of the photoluminescence allows its labeling at temperatures as low as 600–700 °C for small Er concentrations (1 mol %). Increasing Er concentration promotes its enrichment at the nanocrystallites surface accomplished by the anatase-to-rutile phase transformation, suggesting that Er ions control the TiO nanocrystals surface properties., This work was supported by the Ministerio de Economía y Competitividad (MINECO, Government of Spain) under Grants MINECO/FEDER TEC2015-69916-C2-1-R and MAT2015-65356-C3-1-R. IC and MB acknowledge the grants JAE-Pre-201100578 and JAE-Pre-083, respectively., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Strong subbandgap photoconductivity in GaP implanted with Ti

  • Olea, Javier
  • Prado, Álvaro del
  • García-Hemme, E.
  • García-Hernansanz, R.
  • Montero, D.
  • González-Díaz, Germán
  • Gonzalo de los Reyes, J.
  • López, E.
  • Siegel, Jan
  • López, Esther
9 pags., 6 figs., 1 tab., Photovoltaic solar cells based on the intermediate band (IB) concept could greatly enhance the efficiency of future devices. We have analyzed the electrical and photoconductivity properties of GaP supersaturated with Ti to assess its suitability for IB solar cells. GaP:Ti was obtained by ion implantation followed by pulsed-laser melting (PLM) using an ArF excimer laser. It was found that PLM energy densities between 0.35 and 0.55 J/cm produced a good recovery of the crystalline structure of GaP (both unimplanted and implanted with Ti), as evidenced by high mobility measured values (close to the reference GaP). Outside this energy density window, the PLM failed to recover the crystalline structure producing a low mobility layer that is electrically isolated from the substrate. Spectral photoconductivity measurements were performed by using the van der Pauw set up. For GaP:Ti a significant enhancement of the conductivity was observed when illuminating the sample with photon energies below 2.26 eV, suggesting that this photoconductivity is related to the presence of Ti in a concentration high enough to form an IB within the GaP bandgap. The position of the IB was estimated to be around 1.1 eV from the conduction band or the valence band of GaP, which would lead to maximum theoretical efficiencies of 25% to 35% for a selective absorption coefficients scenario and higher for an overlapping scenario., This work was partially supported by Project MADRID‐PV (grant no. P2013/MAE‐2780) funded by the Comunidad de Madrid, by the Spanish MINECO (Ministerio de Economía y Competitividad) under grants TEC 2013‐41730‐R and TEC 2015‐ 69916‐C2‐1‐R, and by the Universidad Complutense de Madrid (Programa de Financiación de Grupos de Investigación UCM–Banco Santander) under grant 910173‐2014. The work of D. Montero was supported by the Spanish MINECO under contract BES‐2014‐ 067585., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optical properties of bismuth nanostructures towards the ultrathin film regime

  • Toudert, Johann
  • Serna, Rosalía
  • Deeb, C.
  • Rebollar, Esther
13 pags., 9 digs., 1 tab. -- Open Access funded by Creative Commons Atribution Licence 4.0, Bulk bismuth presents outstanding optical properties, such as a giant infrared refractive index (n~10) and a negative ultraviolet-visible permittivity induced by giant interband electronic transitions. Although such properties are very appealing for applications in nanophotonics, the dielectric function of bismuth nanostructures has been scarcely studied. Here, we determine by spectroscopic ellipsometry the far infrared-to-ultraviolet dielectric function of pulsed laser deposited bismuth thin films with nominal thickness tBi varied from near 10 nm to several tens of nm. For t > 15 nm, the films display a continuous structure and their dielectric function is comparable with that of bulk bismuth. For t < 15 nm, the film structure is discontinuous, and the dielectric function differs markedly from that of bulk bismuth. It is proposed from FDTD simulations that this marked difference arises mainly from effective medium effects induced by the discontinuous film structure, where quantum electronic confinement does not play a dominant role. This suggests that ultrathin and continuous bismuth films should present the same outstanding optical properties as bulk bismuth for high performance nanophotonic devices., Ministerio de Ciencia, Innovación y Universidades (MICINN) (MICINN RTI2018-096498-B-I00, MINECO/FEDER TEC2015-69916-C2-1-R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mid-to-far infrared tunable perfect absorption by a sub - λ/100 nanofilm in a fractal phasor resonant cavity

  • Toudert, Johann
  • Serna, Rosalía
  • Garcia-Pardo, Marina
  • Ramos, Nicolás
  • Peláez, Ramón J.
  • Maté, Belén
17 pags., 12 figs., Integrating an absorbing thin film into a resonant cavity is the most practical way to achieve perfect absorption of light at a selected wavelength in the mid-to-far infrared, as required to target blackbody radiation or molecular fingerprints. The cavity is designed to resonate and enable perfect absorption in the film at the chosen wavelength λ. However, in current state-of-the-art designs, a still large absorbing film thickness (∼λ/50) is needed and tuning the perfect absorption wavelength over a broad range requires changing the cavity materials. Here, we introduce a new resonant cavity concept to achieve perfect absorption of infrared light in much thinner and thus, really nanoscale films, with a broad wavelength tenability by using a single set of cavity materials. It requires a nanofilm with giant refractive index and small extinction coefficient (found in emerging semi-metals, semi-conductors and topological insulators) backed by a transparent spacer and a metal mirror. The nanofilm acts both as absorber and multiple reflector for the internal cavity waves, which after escaping follow a fractal phasor trajectory. This enables a totally destructive optical interference for a nanofilm thickness more than 2 orders of magnitude smaller than λ. With this remarkable effect, we demonstrate angle-insensitive perfect absorption in sub - λ/100 bismuth nanofilms, at a wavelength tunable from 3 to 20 μm., European Social Fund (ESF); Spanish Ministry for Economy and Competitiveness (MINECO) (MINECO/ERDF TEC2015-69916-C2-1-R); European Regional Development Fund (ERDF) (MINECO/ERDF TEC2015-69916-C2-1-R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Two-dimensional carbon nanostructures obtained by laser ablation in liquid: effect of an ultrasonic field

  • Escobar Alarcón, L.
  • Espinosa-Pesqueira, M. E.
  • Solís-Casados, Dora Alicia
  • Gonzalo de los Reyes, J.
  • Solís Céspedes, Javier
  • Martínez-Orts, M.
  • Haro-Poniatowski, E.
7 pags., 6 figs., The ablation of a carbon target immersed in deionized water, in absence and in presence of ultrasonic waves is reported, and the differences investigated. The obtained nanostructures are characterized by transmission electron microscopy, Raman spectroscopy and photoluminescence. Transmission electron images reveal that the produced carbon nanostructures, with and without ultrasonic excitation, are graphene-like sheets with improved quality in the first case. Samples prepared with ultrasounds show graphene layers with large sizes (several microns) and regular shapes, whereas the samples prepared without ultrasounds show smaller sizes and irregular shapes; additionally, some dispersed quasi-spherical nanoparticles are observed in the samples prepared without ultrasound. Photoluminescence measurements of the obtained nanostructures reveal emission in the blue spectral region., This work was partially supported by the CONACYT project CB-240998 and the Spanish project MINECO/FEDER TEC2015-69916-C2-1-R. Additionally, ININ through the project CB-602 is acknowledged. M. Martinez-Orts acknowledges the financial support of the Autonomous Community of Madrid and the European Social Fund (contract E-28-2017-0679526). The technical support with TEM measurements provided by P. Castillo of the electron microscopy laboratory of UAMI is also recognized.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Self-Assembled Nanostructured Photonic-Plasmonic Metasurfaces for High-Resolution Optical Thermometry

  • Baraldi, G.
  • Garcia-Pardo, Marina
  • Gonzalo de los Reyes, J.
  • Serna, Rosalía
  • Toudert, Johann
7 pags., 3 figs., Sensing devices for environment, safety, healthcare, and optoelectronic applications require an accurate and noninvasive monitoring of their tem- perature, because its variations markedly affect the overall response of the device. Monitoring the optical response of temperature-sensitive integrated photonic elements, such as microresonators or microinterferometers, is an appealing solution in this context. However, achieving high-resolution optical thermometry with such elements is unpractical and costly as this requires lithography processing, highly monochromatic laser sources, complex light coupling strategies. Here, a photonic-plasmonic metasurface design that ena- bles practical optical thermometry with a sub-10¿3 °C resolution is proposed. It is based on a self-assembled nanostructured material implemented with a lithography-free process. The optical response of the temperature-sensitive metasurface is probed using a white light source and by monitoring the optical phase in a standard reflectance configuration. This facile, yet pow- erful, sensing scheme stands on the effective response of the metasurface, which involves the hybridization of thin film interference and low-quality- factor plasmon resonances to enable a quasi-darkness response with a sharp spectral variation (jump) of the optical phase. Such jump is equivalent with a high-quality-factor resonator that yields a high sensor responsivity and thus enables high-resolution optical thermometry., M.G.P. acknowledges support from the European Social Fund and G.B. a CSIC-JAE predoctoral grant, cofunded by the European Social Fund. This work was funded in part by the Spanish Ministry for Economy and Competitiveness through the project MINECO/FEDER TEC2015-69916-C2-1-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Silicon oxynitride nanofilms prepared by PLD with controlled Eu-local concentration for broadband white light emitters

  • Camps, I.
  • Mariscal, A.
  • Serna, Rosalía
5 pags., 5 figs., 1 tab., We report the successful preparation and characterization of active silicon oxynitride thin films with controlled europium (Eu) doping by alternated pulsed laser deposition. The successful Eu doping with a nanostructured dopant distribution, as well as the stoichiometry of the oxynitride film, have been determined by ion beam analysis (RBS). The oxidation state of the incorporated Eu ions has been determined by in-depth x-ray photoelectron spectroscopy (XPS) and it is shown that the Eu ions are in the 2+ state, in contrast to the usual results found in oxide matrices for which the 3+ oxidation state prevails. The Eu-doped films show an intense broadband emission (FWHM >210 nm) associated to the optical transition fd → S of the Eu ions within the amorphous matrix. As expected, the intensity of the emission band increases as the Eu concentration increases, and it is remarkable that the emission shifts towards longer wavelengths. In terms of the chromatic coordinates (CIE) this implies a color tuning from a bluish to orange that enables color tunable emission, and potential white like emission by combining layers with different Eu ions concentration. Therefore, the developed oxynitride films with controlled Eu ions concentration achieved by PLD are promising for the development of color -tailored LED's., This work was partially funded by Spanish grants MINECO/FEDER TEC2015-69916-C2-1-R, MICINN/FEDER RTI2018-096498-B-I00 and PID2021-123190OB-I00, and by the CSIC (Spain) grants PIE202050E195 and AEPP2021-128. I.C. acknowledges the financial support through CSIC scholarship JAE-Pre2011 00578. A.M. acknowledges the financial support through FPI grant BES-2013-062593