Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Semitransparent wide bandgap Cu2ZnGe(S,Se)4 thin-film solar cells: role of the sulfurization process

  • Ruiz-Perona, Andrea
  • Palma-Lafuente, David
  • Sánchez, Yudania
  • Guc, Maxim
  • Kodalle, Tim
  • Salem, Mohamed Ould
  • Placidi, Marcel
  • Serna, Rosalia
  • Pérez-Rodríguez, Alejandro
  • Merino Álvarez, José Manuel
  • Caballero Mesa, Ana Raquel
Semitransparent solar cells are very attractive due to the increasing integration in daily life. Kesterite-type based thin-film solar cells stand out because of its environmentally benign composition and outstanding stability. Herein, the influence of the back contact (Mo/V2O5/FTO or Mo/FTO) and thickness of Cu2ZnGe(S,Se)4 (CZGSSe) absorber layer, grown by sulfurization of coevaporated CZGSe, is investigated. To increase the transparency, thinner absorber layers with higher bandgap energy are produced. A double sulfur gradient through the CZGSSe layer with a considerable S content near the back contact and the formation of Mo(S,Se)2 phase at the back interface is detected for an absorber of only 400 nm thickness. Efficiencies of 3.1% and 2.7% are achieved for 1.2 μm CZGSSe-based devices with Eg of 1.73 and 1.86 eV, respectively, while enabling transmittance values higher than 20% in the near-infrared (NIR). The highest transmittance, 40% in the NIR, is achieved for the 400 nm CZGSSe-based solar cells with Eg of 2.1 eV; however, a significant reduction of these devices’ performance is obtained due to the presence of ZnS secondary phase and a different back-contact interface formation. This work presents the first promising semitransparent CZGSSe solar cells, opening new paths of applications, This work was supported by CELL2WIN (PID2019‐104372RB‐C32), InnoPV (PID2022‐140226OB‐C33) funded by MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe,” ASSESS (TED2021‐129666B‐C21 and TED2021‐129666B‐C22) funded by MCIN/AEI/10.13039/501100011033 by the “European Union NextGenerationEU/PRTR” and the European Project INFINITE‐CELL (H2020‐MSCA‐RISE‐2017‐777968). M.P. and M.G. acknowledge the financial support from the Spanish Ministry of Science, Innovation and Universities within the Ramón y Cajal (grant no. RYC‐2017‐23758) and Ramón y Cajal (grant no. RYC2022‐035588‐I) programs, respectively. A.R.P. also acknowledges the financial support from Community of Madrid within Youth Employment Program (grant no. PEJD‐2017‐PRE/IND‐4062). The authors would also like to thank Fátima Cabello and Marina García for technical support.
Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Sulfurization of co-evaporated Cu2ZnGeSe4 layers: Influence of the precursor cation’s ratios on the properties of Cu2ZnGe(S,Se)4 thin films

  • Palma Lafuente, David
  • Diez Silva, Pablo
  • Rotaru, Victoria
  • Jawhari, Tariq
  • Bertram, Tobias
  • Reyes Figueroa, Pablo
  • Guc, Maxim
  • Merino Álvarez, José Manuel
  • Caballero Mesa, Ana Raquel
Cu2ZnGe(S,Se)4 (CZGSSe) thin films were fabricated by sulfurization of co-evaporated Cu2ZnGeSe4 (CZGSe) thin films. The goal of this work is to investigate the effect of the composition of CZGSe layers on the structural, vibrational and morphological properties of CZGSSe compounds. Different CZGSe layers with different cation's ratios (Cu-poor, Zn-rich; Cu-poor, Zn-stoichiometric and Cu-poor, Ge-rich) were investigated before and after the sulfurization process. Break-off and different cooling experiments during sulfurization of CZGSe were also carried out. Break-off experiments revealed that 440 °C is the key temperature to incorporate S into CZGSe lattice, being required 480 °C to enhance the interdiffusion of the elements. Fast cooling experiments during sulfurization appeared to be a promising strategy to avoid the formation of secondary phases. All the samples showed the CZGSSe kesterite phase, as well as higher S content and different secondary phases at the surface. These experiments demonstrate that a minimum Ge content in CZGSe is required to assist the growth of CZGSSe grains and develop a compact structure. These results indicate the importance of controlling the cation's ratio of CZGSe to develop high quality wide band gap CZGSSe compounds, which can be very attractive for different applications, This work was supported by Spanish Ministry of Science, Innovation and Universities Project (CELL2WIN: PID2019-104372RB-C32) and European Project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). DPL acknowledges the financial support from Spanish Ministry of Science and Innovation within FPI Program. MG acknowledges the financial support from Spanish Ministry of Science, Innovation and Universities within the Juan de la Cierva Program (IJC2018-038199-I). Authors from IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the “Generalitat de Catalunya” (Ref. 2017 SGR 862). The authors acknowledge the service from the MiNa Laboratory at IMN-CSIC, and funding from CM (project S2018/NMT-4291 TEC2SPACE), MINECO (project CSIC13-4E-1794) and European Union (FEDER, FSE)
Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2ZnSnS4 bulk poly-crystals

  • Levcenko, S.
  • Hajdeu-Chicarosh, E.
  • Garcia-Llamas, E.
  • Caballero, Raquel
  • Serna, R.
  • Bodnar, I. V.
  • Victorov, I.
  • Guc, M.
  • Merino Álvarez, José Manuel
  • Pérez-Rodriguez, A.
  • Arushanov, E.
  • León, M.
The linear optical properties of Cu2ZnSnS4 bulk poly-crystals have been investigated using spectroscopic ellipsometry in the range of 1.2-4.6 eV at room temperature. The characteristic features identified in the optical spectra are explained by using the Adachi analytical model for the interband transitions at the corresponding critical points in the Brillouin zone. The experimental data have been modeled over the entire spectral range taking into account the lowest E0 transition near the fundamental absorption edge and E1A and E1B higher energy interband transitions. In addition, the spectral dependences of the refractive index, extinction coefficient, absorption coefficient, and normal-incidence reflectivity values have been accurately determined and are provided since they are essential data for the design of Cu2ZnSnS4 based optoelectronic devices, The research leading to the presented results was partially supported by the European Project INFINITE-CELL (Ref. H2020-MSCA-RISE-2017-777968, 2017–2021, www.infinitecell.eu) and the Spanish MINECO Projects “WINCOST” (ENE2016-80788-C5-2-R) and PHOTOMANA (TEC2015- 69916-C2-1-R). The authors from the Institute of Applied Physics appreciate the financial support from STCU 6224 and from the Institutional Project No. CSSDT 15.817.02.04A
Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Effect of Na and the back contact on Cu2Zn(Sn,Ge)Se4 thin-film solar cells: Towards semi-transparent solar cells

  • Ruiz-Perona, Andrea
  • Sánchez, Yudania
  • Guc, Maxim
  • Khelifi, Samira
  • Kodalle, Tim
  • Placidi, Marcel
  • León Macarrón, Máximo
  • Caballero Mesa, Ana Raquel
  • Merino Álvarez, José Manuel
Cu2ZnSn1-xGexSe4 (CZTGSe) thin films have been grown onto Mo/SLG and Mo/V2O5/FTO/SLG substrates using thermal co-evaporation followed by a subsequent thermal annealing. A NaF precursor layer was evaporated prior to the deposition of the kesterite absorber layer. In the samples grown on Mo/SLG, it has been found that Na promotes Ge incorporation into the Cu2ZnSnSe4 lattice. The high concentration of incorporated Ge leads to the segregation of Sn-Se secondary phases as well as to an accumulation of Sn next to the Mo layer. The use of 12 and 16 nm NaF thick precursor layers prior to the CZTGSe deposition leads to absorber band gaps of 1.30 and 1.34 eV, and to device performances of 4.7 and 4.0%, respectively. A higher Na content, furthermore, caused the formation of bigger grains, a higher charge carrier concentration and a shorter depletion width. A 12 nm NaF precursor layer was used for the devices grown on FTO-based substrates, producing an optimal back contact that allows achieving efficiencies of 5.6% and transmittance of 30% in the near infrared range. This enhanced performance can be associated with the absence of secondary phases and Ge distribution through the absorber layer. The formation of a MoSe2 layer at the back interface in all the investigated devices seems to play a crucial role to improve the solar cell efficiency, This work was supported by Spanish Ministry of Science, Innovation and Universities Project (WINCOST, ENE2016-80788-C5-2-R) and European Project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). ARP also acknowledges financial support from Community of Madrid within Youth Employment Program (PEJD-2017-PRE/IND-4062). MG acknowledges the financial support from ACCIÓ-Generalitat de Catalunya within the TECNIOspring Plus fellowship (TECSPR18-1-0048). MP acknowledges the financial support from Spanish Ministry of Science, Innovation and Universities within the Ramón y Cajal Program (RYC-2017-23758). The authors would like to thank K. Mayer-Stillrich and M. Hartig at PVComB-HZB for Mo deposition, Dr. G. San Vicente from CIEMAT for allowing to perform transmittance mesaurements, Prof. Dr. F. Briones from Instituto de Micro y Nanotecnología, CSIC, and Dr. I. Fernández from Nano4Energy for the technical support with the Se evaporation source.
Dipòsit Digital de la UB
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2ZnSnS4 bulk poly-crystals

  • Levcenko, Sergiu
  • Hajdeu Chicarosh, Elena
  • Garcia Llamas, Elena
  • Caballero, Raquel
  • Serna, Rosalía
  • Bodnar, Ivan V.
  • Victorov, Ivan A.
  • Guc, Maxim
  • Merino, José Manuel
  • Pérez Rodríguez, Alejandro
  • Arushanov, Ernest
  • León, Máximo
The linear optical properties of Cu2ZnSnS4 bulk poly-crystals have been investigated using spectroscopic ellipsometry in the range of 1.2-4.6 eV at room temperature. The characteristic features identified in the optical spectra are explained by using the Adachi analytical model for the interband transitions at the corresponding critical points in the Brillouin zone. The experimental data have been modeled over the entire spectral range taking into account the lowest E0 transition near the fundamental absorption edge and E1A and E1B higher energy interband transitions. In addition, the spectral dependences of the refractive index, extinction coefficient, absorption coefficient, and normal-incidence reflectivity values have been accurately determined and are provided since they are essential data for the design of Cu2ZnSnS4 based optoelectronic devices.
Dipòsit Digital de la UB
Publicación Artículo científico (JournalArticle)

Progress and perspectives of thin film kesterite photovoltaic technology: a critical review

  • Giraldo Muñoz, Sergio
  • Jehl Li-Kao, Zacharie
  • Placidi, Marcel
  • Izquierdo Roca, Victor
  • Pérez Rodríguez, Alejandro
  • Saucedo Silva, Edgardo
The latest progress and future perspectives of thin film photovoltaic kesterite technology are reviewed herein. Kesterite is currently the most promising emerging fully inorganic thin film photovoltaic technology based on critical raw-material-free and sustainable solutions. The positioning of kesterites in the frame of the emerging inorganic solar cells is first addressed, and the recent history of this family of materials briefly described. A review of the fast progress achieved earlier this decade is presented, toward the relative slowdown in the recent years partly explained by the large open circuit voltage (VOC) deficit recurrently observed even in the best solar cell devices in the literature. Then, through a comparison with the close cousin Cu(In,Ga)Se2 technology, doping and alloying strategies are proposed as critical for enhancing the conversion efficiency of kesterite. In the second section herein, intrinsic and extrinsic doping, as well as alloying strategies are reviewed, presenting the most relevant and recent results, and proposing possible pathways for future implementation. In the last section, a review on technological applications of kesterite is presented, going beyond conven tional photovoltaic devices, and demonstrating their suitability as potential candidates in advanced tandem concepts, photocatalysis, thermoelectric, gas sensing, etc.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2ZnSnS4 bulk poly-crystals

  • Levcenko, S.
  • Hajdeu-Chicarosh, E.
  • García-Llamas, E.
  • Caballero, Raquel
  • Serna, Rosalía
  • Bodnar, I. V.
  • Victorov, I. A.
  • Guc, M.
  • Merino, J. M.
  • Pérez-Rodríguez, A.
  • Arushanov, E.
  • León, M.
5 pags., 3 figs., 3 tabs., The linear optical properties of Cu2ZnSnS4 bulk poly-crystals have been investigated using spectroscopic ellipsometry in the range of 1.2–4.6 eV at room temperature. The characteristic features identified in the optical spectra are explained by using the Adachi analytical model for the interband transitions at the corresponding critical points in the Brillouin zone. The experimental data have been modeled over the entire spectral range taking into account the lowest E0 transition near the fundamental absorption edge and E1A and E1B higher energy interband transitions. In addition, the spectral dependences of the refractive index, extinction coefficient, absorption coefficient, and normal-incidence reflectivity values have been accurately determined and are provided since they are essential data for the design of Cu2ZnSnS4 based optoelectronic devices. Published by AIP Publishing., The research leading to the presented results was partially supported by the European Project INFINITE-CELL (Ref. H2020-MSCA-RISE-2017-777968, 2017–2021, www.infinitecell. eu) and the Spanish MINECO Projects “WINCOST” (ENE2016-80788-C5-2-R) and PHOTOMANA (TEC2015- 69916-C2-1-R). The authors from the Institute of Applied Physics appreciate the financial support from STCU 6224 and from the Institutional Project No. CSSDT 15.817.02.04A, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2ZnSn(SxSe1-x)4 bulk polycrystals

  • Levcenko, S.
  • Hajdeu-Chicarosh, E.
  • Serna, Rosalía
  • Guc, Maxim
  • Victorov, I. A.
  • Nateprov, A.
  • Caballero, Raquel
  • Merino, J. M.
  • Arushanov, E.
  • León, M.
6 pags., 4 figs., 2 tabs., The pseudo dielectric function of CuZnSn(SSe) [x = 0.35, 0.62, 0.81] bulk polycrystals is determined over the range 1.1–4.6 eV at room temperature from the analysis of spectroscopic ellipsometry data using the Adachi model. From the analysis, the lowest E transition and high energy E and E transitions are clearly identified, and used to follow the evolution of the pseudo dielectric function as a function of the composition. It is shown that the fundamental E and high energy E transitions can be tuned by increasing the sulfur content over a range of 0.3 eV. These results show the potential of the kesterite compounds for the design of efficient tailored photovoltaic solar cells., The research leading to the presented results was partially supported by the European Project INFINITE-CELL (Ref. H2020-MSCA-RISE-2017-777968, 2017e2021,www.infinitecell.eu) andthe Spanish MINECO Projects“WINCOST”(ENE2016-80788-C5-2-R) and“SENSIL”RTI2018-096498-B-I00 (MCIU/AEI/FEDER, UE).The authors from the Institute of Applied Physics appreciate the financial support from the Bilateral Project No. ANCD19.80013.16.02.01F/BL and from the Institutional Project No. CSSDT15.817.02.04A. Authors from IREC belong to the M-2E (Electronic Materials for Energy) Consolidated Research Group and the XaR-MAE Network of Excellence on Materials for Energy of the“Generalitat de Catalunya”. M. Guc thanks Generalitat de Catalunya for the TECNIO springþ fellowship (TECSPR18-1-0048).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The effect of annealing temperature on Cu2ZnGeSe4 thin films and solar cells grown on transparent substrates

  • Ruiz-Perona, Andrea
  • Sánchez, Yudania
  • Guc, Maxim
  • Kodalle, Tim
  • Placidi, Marcel
  • Merino, J.M.
  • Cabello, Fátima
  • Garcia-Pardo, Marina
  • León, Máximo
  • Caballero, Raquel
9 pags., 7 figs., 2 tabs., Semi-transparent solar cells are the next step for photovoltaics into our daily life. Over the last years, kesterite-type material has attracted a special attention to be used as an absorber in thin-film solar cells because of its low toxicity and earth abundant constituents. Here, Cu2ZnGeSe4 (CZGSe) thin films are grown by co-evaporation and subsequent annealing at a maximum temperature of 480 ◦C or 525 ◦C onto Mo/V2O5/FTO/glass stacks. The goal of this work is to investigate the influence of the annealing temperature on the composition, morphology, vibrational properties, and transmittance of CZGSe layers, the formation of secondary phases, and distribution of elements within the absorber layer as well as on the optoelectronic properties of the corresponding solar cell devices. Raising the annealing temperature to 525 ◦C leads to a more uniform distribution of Cu, Zn, Ge and Se throughout the absorber layer, a reduction of the presence of the GeSe2 secondary phase, which is mainly detected at 480 ◦C, a larger grain size and the formation of a thicker MoSe2 layer at the CZGSe/back contact interface. The strategy of increasing the annealing temperature allows for improved J–V characteristics and higher spectral response resulting in an enhanced device performance of 5.3% compared to 4.2% when using 525 ◦C and 480 ◦C, respectively. Both absorber layers present an optical band gap energy of 1.47 eV. Furthermore, higher annealing temperature has beneficial effect to the CZGSe-based devices without losses in total transmitted light because of the higher diffuse transmittance. This work shows first promising semi-transparent CZGSe-based solar cells possibly open up new routes of applications., This work was supported by Spanish Ministry of Science, Innovation and Universities Project WINCOST (ENE2016-80788-C5-2-R), Project RTI (2018-096498-B-I00, AEI/MICINN/ERDF) and European Project INFINITE CELL (H2020-MSCA-RISE-2017-777968). Authors from IREC belong to the SEMS (Solar EnergyMaterials and Systems) Consolidated Research Group of the ‘Generalitat de Catalunya’ (Ref 2017 SGR 862).MG and MP acknowledge the financial support from Spanish Ministry of Science, Innovation and Universities within the Juan de la Cierva (IJC2018-038199-I) and Ramón y Cajal (RYC-2017-23758) Fellowships respectively. MGP also acknowledges funding from AEI/MICINN (PTA2019-016763-I). The authors acknowledge the service from the MiNa Laboratory at IMN-CSIC, and funding from CM (project S2018/NMT-4291 TEC2SPACE), MINECO (project CSIC13-4E-1794) and European Union (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2Zn(GexSi1-x)Se4 bulk poly-crystals

  • Hajdeu-Chicarosh, E.
  • Levcenko, S.
  • Serna, Rosalía
  • Bodnar, I. V.
  • Victorov, I. A.
  • Iaseniuc, Oxana
  • Caballero, Raquel
  • Merino, J. M.
  • Arushanov, E.
  • León, Máximo
5 pags., 3 figs., 2 tabs., The present study addresses to the synthesis and determination of the dielectric function of CuZn(GeSi)Se solid solutions with x = 0.4 and 0.8 over the range 1–4.5 eV by spectroscopic ellipsometry analysis, with the aim to achieve a suitable band gap tuning. The dielectric function of the samples is determined using the Adachi model. From the analysis the lowest E transition and high energy E and E transitions are identified. It is found that the band gap varies nonlinearly on composition in the CuZn(GeSi)Se alloys and band gap values as large as 1.87 eV are obtained. These results are essential for the design of efficient tailored photovoltaic solar cells and show the high potential of the kesterite compounds for the development of low-cost sustainable future solar cells., This research was supported by the H2020 programme under the project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). The authors appreciate also the financial support from the Institutional Project ANCD 20.80009.5007.03., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Semitransparent Wide Bandgap Cu2ZnGe(S,Se)4Thin-FilmSolar Cells: Role of the Sulfurization Process

  • Ruiz-Perona, Andrea
  • Palma-Lafuente, David
  • Sánchez, Yudania
  • Guc, Maxim
  • Kodalle, Tim
  • Salem, Mohamed Ould
  • Placidi, Marcel
  • Serna, Rosalía
  • Pérez-Rodríguez, Alejandro
  • Merino, José Manuel
  • Caballero, Raquel
9 pags., 6 figs., 2 tabs., Semitransparent solar cells are very attractive due to the increasing integration in daily life. Kesterite-type based thin-film solar cells stand out because of its environmentally benign composition and outstanding stability. Herein, the influence of the back contact (Mo/V2O5/FTO or Mo/FTO) and thickness of Cu2ZnGe(S,Se)4 (CZGSSe) absorber layer, grown by sulfurization of coevaporated CZGSe, is investigated. To increase the transparency, thinner absorber layers with higher bandgap energy are produced. A double sulfur gradient through the CZGSSe layer with a considerable S content near the back contact and the formation of Mo(S,Se)2 phase at the back interface is detected for an absorber of only 400 nm thickness. Efficiencies of 3.1% and 2.7% are achieved for 1.2 μm CZGSSe-based devices with Eg of 1.73 and 1.86 eV, respectively, while enabling transmittance values higher than 20% in the near-infrared (NIR). The highest transmittance, 40% in the NIR, is achieved for the 400 nm CZGSSe-based solar cells with Eg of 2.1 eV; however, a significant reduction of these devices’ performance is obtained due to the presence of ZnS secondary phase and a different back-contact interface formation. This work presents the first promising semitransparent CZGSSe solar cells, opening new paths of applications., This work was supported by CELL2WIN (PID2019-104372RB-C32), InnoPV(PID2022-140226OB-C33) funded by MCIN/AEI/ 10.13039/501100011033and by“ERDF A way of making Europe,”ASSESS (TED2021-129666B-C21and TED2021-129666B-C22) funded by MCIN/AEI/10.13039/501100011033 by the“European Union NextGenerationEU/PRTR”andthe European Project INFINITE-CELL (H2020-MSCA-RISE-2017-777968).M.P. and M.G. acknowledge thefinancial support from the SpanishMinistry of Science, Innovation and Universities within the Ramón yCajal (grant no. RYC-2017-23758) and Ramón y Cajal (grant no.RYC2022-035588-I) programs, respectively. A.R.P. also acknowledgesthefinancial support from Community of Madrid within YouthEmployment Program (grant no. PEJD-2017-PRE/IND-4062)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sulfurization of co-evaporated Cu2ZnGeSe4 layers: Influence of the precursor cation's ratios on the properties of Cu2ZnGe(S,Se)4 thin films

  • Palma-Lafuente, David
  • Diez-Silva, Pablo
  • Rotaru, Victoria
  • Jawhari, Tariq
  • Bertram, Tobias
  • Reyes-Figueroa, Pablo
  • Guc, Maxim
  • Merino, José Manuel
  • Caballero, Raquel
12 pages, 16 figures, 1 table, Cu2ZnGe(S,Se)4 (CZGSSe) thin films were fabricated by sulfurization of co-evaporated Cu2ZnGeSe4 (CZGSe) thin films. The goal of this work is to investigate the effect of the composition of CZGSe layers on the structural, vibrational and morphological properties of CZGSSe compounds. Different CZGSe layers with different cation's ratios (Cu-poor, Zn-rich; Cu-poor, Zn-stoichiometric and Cu-poor, Ge-rich) were investigated before and after the sulfurization process. Break-off and different cooling experiments during sulfurization of CZGSe were also carried out. Break-off experiments revealed that 440 °C is the key temperature to incorporate S into CZGSe lattice, being required 480 °C to enhance the interdiffusion of the elements. Fast cooling experiments during sulfurization appeared to be a promising strategy to avoid the formation of secondary phases. All the samples showed the CZGSSe kesterite phase, as well as higher S content and different secondary phases at the surface. These experiments demonstrate that a minimum Ge content in CZGSe is required to assist the growth of CZGSSe grains and develop a compact structure. These results indicate the importance of controlling the cation's ratio of CZGSe to develop high quality wide band gap CZGSSe compounds, which can be very attractive for different applications., This work was supported by Spanish Ministry of Science, Innovation and Universities Project (CELL2WIN: PID2019-104372RB-C32) and European Project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). DPL acknowledges the financial support from Spanish Ministry of Science and Innovation within FPI Program. MG acknowledges the financial support from Spanish Ministry of Science, Innovation and Universities within the Juan de la Cierva Program (IJC2018-038199-I). Authors from IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the “Generalitat de Catalunya” (Ref. 2017 SGR 862). The authors acknowledge the service from the MiNa Laboratory at IMN-CSIC, and funding from CM (project S2018/NMT-4291 TEC2SPACE), MINECO (project CSIC13-4E-1794) and European Union (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Wide band gap Cu2ZnGe(S,Se)4 thin films and solar cells: Influence of Na content and incorporation method

  • Ruiz-Perona, Andrea
  • Guc, Maxim
  • Sánchez, Yudania
  • Kodalle, Tim
  • Merino, José M.
  • León, Máximo
  • Caballero, Raquel
9 pages, 9 figures, 2 tables, The influence of the Na content and incorporation procedure into Cu2ZnGe(S,Se)4 (CZGSSe) thin films and solar cells is investigated. The effects of the presence/absence of Se during the deposition of a 15 nm thick NaF layer before and/or after the Cu2ZnGeSe4 (CZGSe) co-evaporation, are compared. Both the Na content, and Na-supply method significantly influence the incorporation of S into the CZGSe lattice and its distribution in the absorber. A [S]/([S] + [Se])-gradient throughout the CZGSSe layers is observed for all the samples and correlated with effects induced by the Na incorporation procedure. For instance, the evaporation of Se together with NaF leads to an increased S concentration in the surface-region of the CZGSSe layer and a modified surface morphology. CZGSSe-based solar cells with band gap energies of about 2 eV are obtained, regardless of the NaF addition method used, while the absence of the NaF layer reduces the S incorporation and the Eg. However, the evaporation of Se together with NaF results in higher Eg and open circuit voltage VOC, probably related to a higher S accumulation near the surface, demonstrating the importance of the [S]/([S] + [Se]) distribution. CZGSSe-based photovoltaic devices with efficiency of 3.2 % and Eg of 2 eV are obtained., This work was supported by Spanish Ministry of Science, Innovation and Universities Project (WINCOST: ENE2016-80788-C5-2-R, CELL2WIN: PID2019-104372RB-C32) and European Project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). MG acknowledges the financial support from Spanish Ministry of Science, Innovation and Universities within the Juan de la Cierva Program (IJC2018-038199-I). Authors from IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the “Generalitat de Catalunya” (Ref. 2017 SGR 862). The authors acknowledge the service from the MiNa Laboratory at IMN-CSIC, and funding from CM (project S2018/ NMT-4291 TEC2SPACE), MINECO (project CSIC13-4E-1794) and European Union (FEDER, FSE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Routes to develop a [S]/([S]+[Se]) gradient in wide band-gap Cu2ZnGe(S,Se)4 thin-film solar cells

  • Ruiz-Perona, Andrea
  • Gurieva, Galina
  • Sun, Michael
  • Kodalle, Tim
  • Sánchez, Yudania
  • Grossberg, Maarja
  • Merino, José Manuel
  • Schorr, Susan
  • León, Máximo
  • Caballero, Raquel
9 pages, 6 figures, 2 tables, Wide band-gap kesterite-based solar cells are very attractive to be used for tandem devices as well as for semi-transparent photovoltaic cells. Here, Cu2ZnGe(S,Se)4 (CZGSSe) thin films have been grown by sulfurization of co-evaporated Cu2ZnGeSe4. The influence of a NaF precursor layer and of a Se capping film on CZGSSe absorbers and solar cells has been investigated. It has been found that the distribution of [S]/([S]+[Se]) through the CZGSSe absorber layer is strongly dependent on the Na content. Na promotes the diffusion of S towards the bulk of the absorber layer. Thicker NaF layers>6 nm lead to a higher S content in the bulk of the absorber layer, but to a decreased accumulation of sulphur at the surface, as detected by GIXRD, GD-OES, and Raman spectroscopy measurements. A relationship between Jsc, FF and Na-content supplied was found; higher Na content resulted in improved solar cell efficiencies. It has also been possible to modify the [S]/([S]+[Se])-gradient throughout the CZGSSe film by the absence of the Se capping layer, achieving devices with 2.7% performance and Eg = 2.0 eV. This work reveals two ways to control the [S]/([S]+[Se]) depth-profile to produce wide band gap CZGSSe absorber layers for efficient solar cells., This work was supported by Spanish Ministry of Science and Innovation Project WINCOST (ENE2016-80788-C5–2-R), CELL2WIN (PID2019-104372RB-C32) and European Project INFINITE-CELL (H2020-MSCA-RISE-2017–777968). ARP also acknowledges financial support from Community of Madrid within Youth Employment Program (PEJD-2017-PRE/IND-4062). M.G. also acknowledges financial support from L′Oréal Baltic For Women in Science Programme and from the European Regional Development (Project TK141)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Na and the back contact on Cu2Zn(Sn,Ge)Se4 thin-film solar cells: Towards semi-transparent solar cells

  • Ruiz-Perona, Andrea
  • Sánchez, Yudania
  • Guc, Maxim
  • Khelifi, Samira
  • Kodalle, Tim
  • Placidi, Marcel
  • Merino, José Manuel
  • León, Máximo
  • Caballero, Raquel
9 pages, 8 figures, 2 tables, Cu2ZnSn1-xGexSe4 (CZTGSe) thin films have been grown onto Mo/SLG and Mo/V2O5/FTO/SLG substrates using thermal co-evaporation followed by a subsequent thermal annealing. A NaF precursor layer was evaporated prior to the deposition of the kesterite absorber layer. In the samples grown on Mo/SLG, it has been found that Na promotes Ge incorporation into the Cu2ZnSnSe4 lattice. The high concentration of incorporated Ge leads to the segregation of Sn-Se secondary phases as well as to an accumulation of Sn next to the Mo layer. The use of 12 and 16 nm NaF thick precursor layers prior to the CZTGSe deposition leads to absorber band gaps of 1.30 and 1.34 eV, and to device performances of 4.7 and 4.0%, respectively. A higher Na content, furthermore, caused the formation of bigger grains, a higher charge carrier concentration and a shorter depletion width. A 12 nm NaF precursor layer was used for the devices grown on FTO-based substrates, producing an optimal back contact that allows achieving efficiencies of 5.6% and transmittance of 30% in the near infrared range. This enhanced performance can be associated with the absence of secondary phases and Ge distribution through the absorber layer. The formation of a MoSe2 layer at the back interface in all the investigated devices seems to play a crucial role to improve the solar cell efficiency., This work was supported by Spanish Ministry of Science, Innovation and Universities Project (WINCOST, ENE2016-80788-C5-2-R) and European Project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). ARP also acknowledges financial support from Community of Madrid within Youth Employment Program (PEJD-2017-PRE/IND-4062). MG acknowledges the financial support from ACCIÓ-Generalitat de Catalunya within the TECNIOspring Plus fellowship (TECSPR18-10048). MP acknowledges the financial support from Spanish Ministry of Science, Innovation and Universities within the Ramón y Cajal Program (RYC-2017-23758). The authors would like to thank K. Mayer-Stillrich and M. Hartig at PVComB-HZB for Mo deposition, Dr. G. San Vicente from CIEMAT for allowing to perform transmittance mesaurements, Prof. Dr. F. Briones from Instituto de Micro y Nanotecnología, CSIC, and Dr. I. Fernández from Nano4Energy for the technical support with the Se evaporation source., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Zn excess on compositional, structural and vibrational properties of Cu2ZnSn0.5Ge0.5Se4 thin films and their effect on solar cell efficiency

  • Ruiz-Perona, A.
  • Sánchez, Y.
  • Guc, M.
  • Calvo-Barrio, L.
  • Jawhari, T.
  • Merino, J. M.
  • León, M.
  • Caballero, Raquel
8 pages, 8 figures, 2 tables, The effect of Zn content on compositional, structural and vibrational properties of Cu2ZnSn1-xGexSe4 (CZTGSe, x ~ 0.5) thin films is studied. Kesterite layer is deposited by co-evaporation onto 5 × 5 cm2 Mo/SLG substrate followed by a thermal treatment at maximum temperature of 480 °C, obtaining areas with different composition and morphology which are due to the sample position in the co-evaporation system and to the non-uniform temperature distribution across the substrate. Kesterite layers with higher Zn amounts are characterized by lower Cu and Ge contents; however, a uniform Ge distribution through the absorber layer is detected in all cases. The excess Zn concentration leads to the formation of ZnSe secondary phase on the surface and in the bulk of the absorber as determined by Raman spectroscopy. When higher Ge content and no ZnSe are present in the absorber layer, a compact structure is formed with larger grain size of kesterite. This effect could explain the higher Voc of the solar cell. The Zn content does not affect the bandgap energy significantly (Eg near 1.3 eV), although the observed effect of Zn excess in CZTGSe results in a decreased device performance from 6.4 to 4.2%. This investigation reveals the importance of the control of the off-stoichiometric CZTGSe composition during the deposition process to enhance solar cells properties., This work was supported by Spanish Ministry of Science, Innovation and Universities Project WINCOST (ENE2016-80788-C5-2-R) and European Project INFINITE CELL (H2020-MSCA-RISE-2017-777968). ARP also acknowledges financial support from Community of Madrid within Youth Employment Program (PEJD-2017-PRE/IND-4062). MG acknowledges the financial support from ACCIÓ-Generalitat de Catalunya within the TECNIOspring Plus fellowship (TECSPR18-10048), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Physical routes for the synthesis of kesterite

  • Ratz, T.
  • Brammertz, G.
  • Caballero, Raquel
  • León, M.
  • Canulescu, S.
  • Schou, J.
  • Gütay, L.
  • Pareek, D.
  • Taskesen, T.
  • Kim, D. H.
  • Kang, J. K.
  • Malerba, C.
  • Redinger, A.
  • Saucedo, E.
  • Shin, B.
  • Tampo, H.
  • Timmo, K.
  • Nguyen, N. D.
  • Vermang, B.
23 pages, 7 figures, 2 tables, This paper provides an overview of the physical vapor technologies used to synthesize Cu2ZnSn(S,Se)4 thin films as absorber layers for photovoltaic applications. Through the years, CZT(S,Se) thin films have been fabricated using sequential stacking or co-sputtering of precursors as well as using sequential or co-evaporation of elemental sources, leading to high-efficient solar cells. In addition, pulsed laser deposition of composite targets and monograin growth by the molten salt method were developed as alternative methods for kesterite layers deposition. This review presents the growing increase of the kesterite-based solar cell efficiencies achieved over the recent years. A historical description of the main issues limiting this efficiency and of the experimental pathways designed to prevent or limit these issues is provided and discussed as well. A final section is dedicated to the description of promising process steps aiming at further improvements of solar cell efficiency, such as alkali doping and bandgap grading., RCaballero and MLeón acknowledge financial support via the Spanish Ministry of Science, Innovation and Universities project (WINCOST,ENE2016-80788-C5-2-R) and thank H2020 EU Programme under the project INFINITE-CELL(H2020-MSCA-RISE-2017-777968). SCanulescu and JSchou acknowledge the support from Innovation Fund Denmark. D-Kim acknowledges financial support via the DGISTR&DProgram of the Ministry of Science and ICT, KOREA(18-BD-05). CMalerba acknowledges the support from the Italian Ministry of Economic Development in the framework of the Operating Agreement with ENEA for the Research on the Electric System. A Redinger acknowledges financial support via the FNR Attract program, Project : SUNSPOT, Nr. 11244141. 6. E Saucedo thanks H2020EUProgramme under the projects STARCELL (H2020-NMBP-03-2016-720907) and INFINITE-CELL(H2020-MSCA-RISE-2017-777968), the Spanish Ministry of Science, Innovation and Universities for the IGNITEproject(ENE2017-87671-C3-1-R),and the European Regional Development Funds (ERDF, FEDER Programa Competitivit at de Cataluny a2007–2013). IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the‘Generalitat de Catalunya’ (Ref.2017SGR862). Taltech acknowledges financial support via the Estonian Ministry of Education and Research funding project IUT19-28 and the European Union Regional Development Fund, ProjectTK141. B Vermang has received funding from the European Research Council (ERC) under the European Union’s Horizon2020 Research and Innovation Programme(GrantAgreement No 715027)., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Transition metal oxides for kesterite solar cells developed on transparent substrates

  • Becerril Romero, Ignacio
  • Sylla, Dioulde
  • Placidi, Marcel Jose|||0000-0001-5684-9669
  • Sánchez González, Yudania|||0000-0002-5740-1150
  • Andrade Arvizu, Jacob
  • Izquierdo Roca, Víctor
  • Guc, Maxim|||0000-0002-2072-9566
  • Pérez Rodríguez, Alejandro
  • Grini, Sigbjørn
  • Vines, Lasse
  • Pusay Villarroel, Benjamín Andrés
  • Almache Hernández, Rosa Estefanía|||0000-0002-3172-5026
  • Puigdollers i González, Joaquim|||0000-0002-1834-2565
  • Pistor, Jan Paul|||0000-0002-9244-915X
  • Saucedo Silva, Edgardo Ademar|||0000-0003-2123-6162
  • Espindola Rodríguez, Moisés|||0000-0003-4843-7474
This document is the unedited Author’s version of a Submitted Work that was subsequently accepted for publication in Transition-Metal Oxides for Kesterite Solar Cells Developed on Transparent Substrates, copyright © American Chemical Society after peer review. To access the final edited and published work see https://pubs.acs.org/doi/10.1021/acsami.0c06992, Fabrication on transparent soda-lime glass/fluorine-doped tin oxide (FTO) substrates opens the way to advanced applications for kesterite solar cells such as semitransparent, bifacial, and tandem devices, which are key to the future of the PV market. However, the complex behavior of the p-kesterite/n-FTO back-interface potentially limits the power conversion efficiency of such devices. Overcoming this issue requires careful interface engineering. This work empirically explores the use of transition-metal oxides (TMOs) and Mo-based nanolayers to improve the back-interface of Cu2ZnSnSe4, Cu2ZnSnS4, and Cu2ZnSn(S,Se)4 solar cells fabricated on transparent glass/FTO substrates. Although the use of TMOs alone is found to be highly detrimental to the devices inducing complex current-blocking behaviors, the use of Mo:Na nanolayers and their combination with n-type TMOs TiO2 and V2O5 are shown to be a very promising strategy to improve the limited performance of kesterite devices fabricated on transparent substrates. The optoelectronic, morphological, structural, and in-depth compositional characterization performed on the devices suggests that the improvements observed are related to a combination of shunt insulation and recombination reduction. This way, record efficiencies of 6.1, 6.2, and 7.9% are obtained for Cu2ZnSnSe4, Cu2ZnSnS4, and Cu2ZnSn(S,Se)4 devices, respectively, giving proof of the potential of TMOs for the development of kesterite solar cells on transparent substrates., This research was supported by the H2020 Programme under the project INFINITE-CELL (H2020-MSCA-RISE-2017-777968), by the Ministry of Science and Innovation of Spain under IGNITE project (ENE2017-87671-C3-1-R), by the European Regional Development Funds (ERDF, FEDER Programa Competitivitat de Catalunya 2007–2013) and CERCA Programme / Generalitat de Catalunya. Authors from IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the “Generalitat de Catalunya” (Ref. 2017 SGR 862), Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Progress and perspectives of thin film kesterite photovoltaic technology: a critical review

  • Giraldo Muñoz, Sergio
  • Jehl Li-Kao, Zacharie
  • Placidi, Marcel
  • Izquierdo Roca, Victor
  • Pérez Rodríguez, Alejandro
  • Saucedo Silva, Edgardo
The latest progress and future perspectives of thin film photovoltaic kesterite technology are reviewed herein. Kesterite is currently the most promising emerging fully inorganic thin film photovoltaic technology based on critical raw-material-free and sustainable solutions. The positioning of kesterites in the frame of the emerging inorganic solar cells is first addressed, and the recent history of this family of materials briefly described. A review of the fast progress achieved earlier this decade is presented, toward the relative slowdown in the recent years partly explained by the large open circuit voltage (VOC) deficit recurrently observed even in the best solar cell devices in the literature. Then, through a comparison with the close cousin Cu(In,Ga)Se2 technology, doping and alloying strategies are proposed as critical for enhancing the conversion efficiency of kesterite. In the second section herein, intrinsic and extrinsic doping, as well as alloying strategies are reviewed, presenting the most relevant and recent results, and proposing possible pathways for future implementation. In the last section, a review on technological applications of kesterite is presented, going beyond conven tional photovoltaic devices, and demonstrating their suitability as potential candidates in advanced tandem concepts, photocatalysis, thermoelectric, gas sensing, etc.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Transition metal oxides for kesterite solar cells developed on transparent substrates

  • Becerril Romero, Ignacio
  • Sylla, Dioulde
  • Placidi, Marcel Jose
  • Sánchez González, Yudania
  • Andrade Arvizu, Jacob
  • Izquierdo Roca, Víctor
  • Guc, Maxim
  • Pérez Rodríguez, Alejandro
  • Grini, Sigbjørn
  • Vines, Lasse
  • Pusay Villarroel, Benjamín Andrés
  • Almache Hernández, Rosa Estefanía
  • Puigdollers i González, Joaquim
  • Pistor, Jan Paul
  • Saucedo Silva, Edgardo Ademar
  • Espindola Rodríguez, Moisés
This document is the unedited Author’s version of a Submitted Work that was subsequently accepted for publication in Transition-Metal Oxides for Kesterite Solar Cells Developed on Transparent Substrates, copyright © American Chemical Society after peer review. To access the final edited and published work see https://pubs.acs.org/doi/10.1021/acsami.0c06992, Fabrication on transparent soda-lime glass/fluorine-doped tin oxide (FTO) substrates opens the way to advanced applications for kesterite solar cells such as semitransparent, bifacial, and tandem devices, which are key to the future of the PV market. However, the complex behavior of the p-kesterite/n-FTO back-interface potentially limits the power conversion efficiency of such devices. Overcoming this issue requires careful interface engineering. This work empirically explores the use of transition-metal oxides (TMOs) and Mo-based nanolayers to improve the back-interface of Cu2ZnSnSe4, Cu2ZnSnS4, and Cu2ZnSn(S,Se)4 solar cells fabricated on transparent glass/FTO substrates. Although the use of TMOs alone is found to be highly detrimental to the devices inducing complex current-blocking behaviors, the use of Mo:Na nanolayers and their combination with n-type TMOs TiO2 and V2O5 are shown to be a very promising strategy to improve the limited performance of kesterite devices fabricated on transparent substrates. The optoelectronic, morphological, structural, and in-depth compositional characterization performed on the devices suggests that the improvements observed are related to a combination of shunt insulation and recombination reduction. This way, record efficiencies of 6.1, 6.2, and 7.9% are obtained for Cu2ZnSnSe4, Cu2ZnSnS4, and Cu2ZnSn(S,Se)4 devices, respectively, giving proof of the potential of TMOs for the development of kesterite solar cells on transparent substrates., This research was supported by the H2020 Programme under the project INFINITE-CELL (H2020-MSCA-RISE-2017-777968), by the Ministry of Science and Innovation of Spain under IGNITE project (ENE2017-87671-C3-1-R), by the European Regional Development Funds (ERDF, FEDER Programa Competitivitat de Catalunya 2007–2013) and CERCA Programme / Generalitat de Catalunya. Authors from IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the “Generalitat de Catalunya” (Ref. 2017 SGR 862), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Spectroscopic ellipsometry study of Cu2ZnSnS4 bulk poly-crystals

  • Levcenko, Sergiu
  • Hajdeu Chicarosh, Elena
  • Garcia Llamas, Elena
  • Caballero, Raquel
  • Serna, Rosalía
  • Bodnar, Ivan V.
  • Victorov, Ivan A.
  • Guc, Maxim
  • Merino, José Manuel
  • Pérez Rodríguez, Alejandro
  • Arushanov, Ernest
  • León, Máximo
The linear optical properties of Cu2ZnSnS4 bulk poly-crystals have been investigated using spectroscopic ellipsometry in the range of 1.2-4.6 eV at room temperature. The characteristic features identified in the optical spectra are explained by using the Adachi analytical model for the interband transitions at the corresponding critical points in the Brillouin zone. The experimental data have been modeled over the entire spectral range taking into account the lowest E0 transition near the fundamental absorption edge and E1A and E1B higher energy interband transitions. In addition, the spectral dependences of the refractive index, extinction coefficient, absorption coefficient, and normal-incidence reflectivity values have been accurately determined and are provided since they are essential data for the design of Cu2ZnSnS4 based optoelectronic devices.