Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 33
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

50-km remote electronic-sensor integration in fiber optic networks using power over fiber and microelectromechanical modulators

  • Rodríguez Rodríguez, Armando
  • López-Amo Sáinz, Manuel
  • Bravo Acha, Mikel
This work presents a power-efficient solution that combines and enables the use of electronic devices in fiber optic networks for environmental monitoring. The system is based on a frequency encoding scheme of the sensor data, which modulates the optical carrier via a microelectromechanical (MEMS) variable optical attenuator (VOA). We demonstrate a remote battery-less sensor node, powered exclusively by power-over-fiber (PoF), over a 50-km standard telecom link, using energy harvesting techniques. As a proof-of-concept, a low-power microcontroller encodes the data from electronic sensors of temperature, eCO2, and pressure in a frequency pattern, which are used as modulating signals. A Frequency Shift Keying (FSK) modulation was implemented, resulting in data rates of up to 1.5 kbps at the maximum corner frequency value of the modulator. The retrieved and decoded data were transmitted via a second optical fiber segment, extending 50 km., This work was supported in part by projects PID2022-137269OB-C21, funded by MCIN/AEI/10.13039/501100011033 and FEDER \u201CA way to make Europe\u201D, and TED2021-130378B-C22, funded by MCIN/AEI/10.13039/501100011033 and European Union \u201CNext generation EU\u201D/PRTR. and the Beatriz Galindo BEAGAL18/00116 grant funded by MICINN.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Optical fiber laser sensor for torsion measurement using a three-core fiber and a nanocrystals-based reflector

  • Correa Serrano, Ángel Ignacio
  • Vento Álvarez, José Raúl
  • Galarza Galarza, Marko
  • Sánchez González, Arturo
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Humbert, Georges
  • Pérez Herrera, Rosa Ana
  • López-Amo Sáinz, Manuel
This study presents a novel and highly sensitive torsion sensor based on a multicore fiber (MCF) inside a Sagnac interferometer, which acts both as a mirror and a sensor head of a fiber ring laser. This laser sensor configuration also incorporates a distributed reflector consisting of an optical fiber segment doped with ZnGa2O4 nanocrystals, enhancing the overall performance. The sensor demonstrates high sensitivity to torsion across a range of 0° to 150°. The phase analysis in the 0°-50° range achieves a sensitivity of 0.08 rad/º. A Machine Learning Integration, with a function-fitting neural network, shows a detection limit of 0.06°., This work was supported in part by projects PID2022-137269OB, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Torsion sensor using a high-birefringence nine-hole optical fiber

  • Rodríguez Rodríguez, Armando
  • Vento Álvarez, José Raúl
  • Galarza Galarza, Marko
  • Vanegas Tenezaca, Evelyn Dayanara
  • Schuster, Kay
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
This article presents a novel high-birefringence fiber-based torsion sensor based on a microstructured optical fiber with nine holes and seven cores microstructured holes and cores optical fiber (MHCF) embedded into a Sagnac interferometer (SI). A segment of this fiber is inserted into a symmetric SMF-MMF-MHCF-MMF-SMF arrangement, which provides efficient coupling to the multiple cores of the birefringent fiber and, consequently, multimode interference (MMI). Fast Fourier transform (FFT) spectral data analysis is employed to enhance measurement stability and reduce dependence on optical source variations. The sensor demonstrates a linear response to torsion angles between −50◦ and +50◦ , with a 16-mrad/◦ sensitivity. The high sensitivity and good linearity of the sensor are enhanced through the application of machine learning (ML) techniques., This work was supported in part by CIN/AEI/10.13039/501100011033 and Fondo Europeo de Desarrollo Regional (FEDER) \u201CA way to make Europe,\u201D under Project PID2022-137269OB; and in part by MCIN/AEI/10.13039/501100011033 and European Union (EU) \u201CNext generation EU\u201D/Plan de Recuperaci\u00F3n, Transformaci\u00F3n y Resiliencia (PRTR) under Project TED2021-130378B. Open access funding provided by Universidad P\u00FAblica de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Erbium-doped fiber ring cavity for the measurement of refractive index variations

  • Pérez Herrera, Rosa Ana
  • Soares, Liliana
  • Novais, Susana
  • Frazão, Orlando
  • Silva, Susana
In this work, an erbium-doped fiber ring cavity based on a 3dB optical coupler for refractive index measurements is presented and experimentally verified. This interrogation system, based on a 1 x 2 optical coupler, uses one of these output ports to increase the reflected optical power by means of a fiber Bragg Grating (FBG), used as a reflector. Moreover, the other output port is used as a refractive index sensing head. A spectral analysis of this interrogator system as well as a fiber cavity ring refractive index sensor characterization are carried out. Finally, an experimental comparison of the refractive index sensor range when the 3dB coupler is replace by a 1x3 one is also presented., This work is financed by the program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Universidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR; and National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020 and FCT, Portugal through the Grant 2020.05297.BD
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Aluminum coated fiber optic sensor for enhancing flow rate measurement

  • Rodríguez Rodríguez, Armando
  • Urroz Unzueta, José Carlos
  • Diéguez Elizondo, Pedro
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
  • López Rodríguez, José Javier
A water flow and velocity aluminum-coated Fiber Bragg Grating sensor system for open channels was designed, simulated and tested. The sensing head was designed, ruggedized and customized to measure velocities at different depths, in order to calculate the discharge in open channels. This paper shows, for the first time to our knowledge, the simulation of such kind of fiber sensors in open channels., This work was supported in part by projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical fiber sensor for water velocity measurement in rivers and channels

  • Rodríguez Rodríguez, Armando
  • Diéguez Elizondo, Pedro
  • Urroz Unzueta, José Carlos
  • Bravo Acha, Mikel
  • López Rodríguez, José Javier
  • López-Amo Sáinz, Manuel
In this work, optical fiber Bragg grating sensors were used to measure water velocity and examine how it was distributed in open channels. Several types of coatings were incorporated into the design of the sensors to examine their effects on the strain that the fibers experienced as a result of the water flow. Due to their low elastic coefficient, which reduced the hysteresis, the results indicated that the aluminum- and acrylate-coated fibers had the best performance. ANSYS-CFX V2020 R2 software was used to model the strain encountered by the fibers under various flow rates to assess the performance of the FBG sensors. The calculations and actual data exhibited good convergence, demonstrating the accuracy of the FBG sensors in determining water velocity. The study illustrated the usability of the proposal in both scenarios by contrasting its application in rivers and channels., This work was supported in part by projects PID2022-137269OB-C21, funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and FEDER 'A way to make Europe', and TED2021-130378B-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and European Union 'Next generation EU'/PTR
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Improved liquid level sensor by using a multi-capillary structure

  • Vanegas Tenezaca, Evelyn Dayanara
  • López-Amo Ocón, Manuel
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
We demonstrate a new optical fiber liquid level sensor based on two sections of capillary optical fibers spliced between single-mode fibers. Last section without coating is in contact with the liquid. A measurement range of 60 mm is obtained when the structure is monitored in reflection by using a FBGs interrogator., This work was supported in part by projects PID2019-107270RB-C02 and PID2022-137269OB-C21 funded by MCIN/AEI/10.13039/501100011033 and FEDER 'A way to make Europe', and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union 'Next generation EU'/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High resolution liquid level measurement using a multisection interferometer based on capillary fibers

  • Vanegas Tenezaca, Evelyn Dayanara
  • Galarza Galarza, Marko
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
This paper presents a novel capillary structure for liquid level measurement. The multifiber interferometric structure, which employs two capillary sections, is well-suited to the measurement of liquid levels in both short distances and with high resolution. The measurement range extends up to 60 mm with a resolution of 0.70 mm., This work was supported in part by the MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe" under Grant PID2022-137269OB-C21 and in part by the MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR under Grant TED2021-130378B-C22. Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Switchable L-band fiber ring laser driven by a motorized polarization fiber controller

  • Janices Chamizo, Iñaki
  • Salinas Anguiano, Álvaro
  • Erro Betrán, María José
  • Tainta Ausejo, Santiago
  • Pérez Herrera, Rosa Ana
In this work, a switchable multiwavelength L-band fiber ring laser based on a polarization-dependent booster optical amplifier (BOA) and a motorized polarization controller is experimentally demonstrated. Lasing wavelengths selection is achieved by automatically adjusting the polarization state, enabling single, dual, or triple line emission., This research was supported by the Public University of Navarre Collaboration grants. This work was supported in part by projects PID2022-137269OB, funded by CIN/AEI/10.13039/501100011033 and FEDER 'A way to make Europe', and TED2021-130378B funded by MCIN/AEI/10.13039/501100011033 and European Union 'Next generation EU'/PRTR, and PID2019-104426GB-100 funded by MCIN/AEI.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Multidirectional bending sensor using capillary fibers and machine learning for real-time applications

  • Vanegas Tenezaca, Evelyn Dayanara
  • Galarza Galarza, Marko
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
In this article, the design and implementation of a bidirectional curvature sensor based on a fiber-optic interferometer are presented. The sensor structure was fabricated by fusing a capillary fiber fragment between single-mode fibers (SMFs), with the addition of a long end capillary to promote a long interferometric section, forming a Fabry-Perot (FP) cavity. Detailed analysis of the curvature data was carried out using machine learning techniques, allowing accurate classification of curvature in both directions of rotation. The experimental results showed excellent agreement (R2: 0.9998) with the predicted values. The sensor exhibits a maximum error of 1.9485°. This approach presents significant potential for applications requiring accurate real-time curvature measurements., This work was supported in part by CIN/AEI/10.13039/501100011033 and FEDER "AWay to Make Europe" under Project PID2022-137269OB and in part by MCIN/AEI/10.13039/501100011033 and European Union "Next Generation EU"/PRTR under Project TED2021-130378B. Open access funding provided by Universidad Publica de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Measurement of paracetamol concentration using a fiber laser system

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Frazão, Orlando
  • Silva, Susana
A linear fiber laser system for measurements of paracetamol concentration is experimentally demonstrated. The cavity is based on a fiber loop mirror and an FBG centered at 1567.8 nm. The sensing head corresponds to a refractometric sensor, whose which principle of operation is based on Fresnel reflection in the fiber tip (FBG side). The system works at detected variations of paracetamol concentrations with a sensitivity of [8.74± 0.34)× 10-5] µW/(g/kg) and a resolution of 2.77 g/kg. The results prove that the fiber laser system could be an asset for processing industries, specifically for non-invasive and real-time measurements of concentration., This work was financially supported by the Wellcome Trust, UK, through the Innovator Award “Light-activated cap for catheter sterilization” (WT223940/Z/21/Z); National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020 and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021- 130378B-C22 funded by MCIN/ AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Low-cost system for vital signs monitoring based on long-period fiber grating

  • Molinos Rodríguez, Ariana
  • Martínez Ortiz, Francisco
  • Erro Betrán, María José
  • Tainta Ausejo, Santiago
  • Pérez Herrera, Rosa Ana
Accurate and continuous respiratory and heart rate monitoring is essential during medical procedures to ensure patient safety. This work explores the feasibility of using LPGs for monitoring in clinical environments where immunity to electromagnetic interference is crucial. Preliminary analysis and results suggest the validity of the proposal. Future research will focus on experimental validation and signal processing techniques to enhance performance., This research was supported by the Public University of Navarre Collaboration grants. This work was supported in part by projects PID2022-137269OB, funded by CIN/AEI/10.13039/501100011033 and FEDER ¿A way to make Europe¿, and TED2021-130378B funded by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical test set for microwave vector network analyzers based on homodyne detection

  • Vallifuoco, Raffaele
  • Sagüés García, Mikel
  • Zeni, Luigi
  • Minardo, Aldo
  • Loayssa Lara, Alayn
We present an optical test set for a microwave vector network analyzer that transforms the instrument into a full vector optical analyzer (OVA), enabling measurements of the optical field transfer function of components and systems with Hz-level frequency resolution. The setup is simple, consisting of a laser source, a standard Mach-Zehnder electro-optic modulator, and a self-homodyne receiver based on a 90° optical hybrid and balanced detectors. Unlike other OVA methods that use RF-modulated optical signals, our technique avoids complex setups and multi-step procedures. It is also immune to errors caused by beating between unwanted modulation sidebands. We provide a detailed theoretical derivation of the mathematical framework underlying the method. In addition, we introduce a calibration technique that compensates for all optical and electrical non-idealities in the setup, including those introduced by the optical hybrid. We demonstrate the system's operation through proof-of-concept experiments, measuring both the magnitude and phase of the optical field transfer function of narrowband optical components., This work was supported in part by MCIN/AEI/10.13039/501100011033 under Grant PID2022-137269OB-C21, in part by ERDF ¿A way to make Europe¿, in part by MCIN/AEI/10.13039/501100011033 under Grant TED2021-130378B-C22, in part by European Union "Next generationEU"/PRTR, and in part by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Wavelength-switchable L-band fiber laser assisted by random reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
A wavelength-switchable L-band erbium-doped fiber laser (EDFL) assisted by an artificially controlled backscattering (ACB) fiber reflector is here presented. This random reflector was inscribed by femtosecond (fs) laser direct writing on the axial axis of a multimode fiber with 50 lm core and 125 lm cladding with a length of 17 mm. This microstructure was placed inside a surgical syringe to be positioned in the center of a high-precision rotation mount to accurately control its angle of rotation. Only by rotating this mount, three different output spectra were obtained: a single wavelength lasing centered at 1574.75 nm, a dual wavelength lasing centered at 1574.75 nm and 1575.75 nm, and a single wavelength lasing centered at 1575.5 nm. All of them showed an optical signal-to-noise ratio (OSNR) of around 60 dB when pumped at 300 mW, This work was financed by the program "José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores", funded by the Ministerio de Universidades of Spain (reference CAS21/00351); the Spanish AEI projects PID2019-107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and projects PDC2021-121172 and TED2021-130378B funded by MCIN/ AEI/10.13039/501100011033 and European Union "Next generation EU"/PTR. Finally, the work was also founded by the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Optical fiber pH sensors based on PAni-coated microstructured optical fibers

  • Rodríguez Rodríguez, Armando
  • Lopes, Guilherme
  • Nedoma, Jan
  • Pereira, Sónia O.
  • Fernandes, Antonio J. S.
  • Jamier, Raphael
  • Roy, Philippe
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
  • Marques, Carlos
In this article, we report the analysis of a novel optical fiber pH sensor based in polyaniline (PAni) coating applied on a trenched core-free (only-bridge) silica fiber. The results are compared to another pH sensor based on side-polished silica fiber. The pH-sensitive polymer is synthesized over the fiber sample by means of oxidative polymerization, keeping records of the time where the reaction occurs to improve the sensitivity. The response to pH is enhanced in the case of the trenched core-free bridge fiber due to the higher interaction of the evanescent field with the PAni film and, thus, the surrounding media. The sensitivity in the linear zone of operation is 1.1 mW/pH, and a total transmittance of 55% in the pH range is 4.2-8.1. The repeatability of both sensors was checked, showing a high capability to perform studies in liquid samples due to its temperature independence, good sensitivity, and long-term stability., This work was supported in part by MCIN/AEI/10.13039/501100011033 under Project PID2022-137269OBC21 and Project TED2021-130378B-C22; in part by the Fondo Europeo de Desarrollo Regional (FEDER) “A way to make Europe;” in part by the European Union “Next Generation EU”/PRTR; in part by Beatriz Galindo in MICINN under Grant BEAGAL18/00116; in part by the CICECO–Aveiro Institute of Materials under Project LA/P/0006/2020, Project UIDB/50011/2020, and Project UIDP/50011/2020; in part by i3N under Project UIDB/50025/2020, Project UIDP/50025/2020, and Project LA/P/0037/2020; in part by DigiAqua under Project PTDC/EEIEEE/0415/2021; in part by the National Funds through the Portuguese Science and Technology Foundation/MCTES (FCT I.P., Portugal); in part by the European Union through the Research Excellence For Region Sustainability and High-Tech Industries (REFRESH) under Project CZ.10.03.01/00/22_003/0000048 via the Operational Program Just Transition; and in part by the Ministry of Education, Youth, and Sports of the Czech Republic through the VSB–Technical University of Ostrava under Grant SP2024/081 and Grant SP2024/059. Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Design of optical fiber Bragg grating-based sensors for flow measurement in pipes

  • Diéguez Elizondo, Pedro
  • Rodríguez Rodríguez, Armando
  • Urroz Unzueta, José Carlos
  • López Rodríguez, José Javier
  • López-Amo Sáinz, Manuel
In this work, optical Fiber Bragg grating (FBG) sensors were used to measure water flow in pipes. Several types of coatings were incorporated into the design of the sensors to examine their effects on the elastic strain that the fiber underwent as a result of the water flow. ANSYS-CFX V2020 R2 software was used to model the elastic strain encountered by the fiber under various flow rates in order to assess the performance of the FBG sensors. The calculations and experimental data exhibited good convergence, demonstrating the accuracy of the FBG sensors in determining water flow. These calculations and procedures can be extrapolated to any other fluid., This work was supported in part by projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Polarization-switched fiber optic ring laser for L-band multiwavelength remote sensing applications

  • Pérez Herrera, Rosa Ana
  • Janices Chamizo, Iñaki
  • San Miguel Zarraluqui, Uxue
  • Salinas Anguiano, Álvaro
  • Sánchez González, Arturo
  • Erro Betrán, María José
  • Tainta Ausejo, Santiago
This work presents the experimental demonstration of a three-channel remote sensor that operates in the L-band. It is based on a fiber ring laser cavity, formed by a semiconductor optical amplifier and three fiber Bragg gratings used both for the selection of the operating wavelengths and the sensing. A polarization-controller allows the activation of one, two or the three emission wavelengths simultaneously. The sensing elements can be situated in a remote localization, without compromising the temperature sensitivity of the experimental setup. To validate this functionality, a 25 km standard single-mode fiber optic reel is incorporated between the FBG-based sensors and the cavity, demonstrating the system's ability to perform long-range sensing while preserving signal integrity and operational reliability., This work was supported in part by projects PID2022-137269OB, funded by MCIN/AEI/10.13039/501100011033 and FEDER 'A way to make Europe', and TED2021-130378B funded by MCIN/AEI/10.13039/501100011033 and European Union 'Next generation EU'/PRTR, and PID2019-104426GB-100 funded by MCIN/AEI. This research was supported by the Public University of Navarre Collaboration grants.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Ring cavity erbium-doped fiber for refractive index measurements

  • Pérez Herrera, Rosa Ana
  • Soares, Liliana
  • Silva, Susana
  • Frazão, Orlando
In this study, an interrogation system based on an erbium-doped fiber ring cavity for refractive index measurements is presented and experimentally demonstrated. This cavity ring includes a 1 × 3 coupler wherein one of the fiber output ports is used to increase the optical power of the system by means of an FBG used as a reflector. The other two output ports are used as a refractive index sensing head and reference port, respectively. An experimental demonstration of this proposed sensor system for the measurement of a distinct refractive index is presented., This work is financed by the program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Universidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR; and National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020. Liliana Soares acknowledges the support of FCT, Portugal through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High frequency vibration sensor using a fiber laser with a multicore fiber interferometer

  • Correa Serrano, Ángel Ignacio
  • Galarza Galarza, Marko
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
  • Pérez Herrera, Rosa Ana
We present an interferometric vibration sensor that uses three-core fibers. The transducer is constructed by splicing a segment 20 mm long of a multicore optical fiber (MCF) to a single-mode optical fiber (SMF). The end of the MCF segment is cut off and painted using silver metallic paint. The sensor head is operated in reflection mode. The structure is placed on a polyvinyl chloride (PVC) plate, which is excited with a wide range of frequency signals. The vibrations induce cyclic bending in the MCF segment, resulting in periodic oscillations of the reflected interference spectrum. This device is demonstrated to be suitable to measure vibrations in a frequency range of the order of 300 kHz detecting deformations as small as 0.40μm ., This work was supported in part by projects PID2019-107270RB-C02 and PID2022- 137269OB-C21, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe,” and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Study of in-line capillary fiber sensor for uniaxial transverse deformation

  • Sánchez González, Arturo
  • Leandro González, Daniel
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Pérez Herrera, Rosa Ana
This research explores the impact of cyclic uniaxial transverse deformation on an in-line hollow-core fiber etalon. The structure consists of a 6 mm long section of capillary fiber spliced between two standard single-mode fibers. The optical response of the structure is theoretically analyzed in spectral and transformed domains, evidencing Fabry-Perot and antiresonant interferometric mechanisms. A validation of the theoretical behavior is carried out both through simulation and experimentation. The performance of the structure for uniaxial transverse deformation is subsequently evaluated by tracking the phase of the main component in the transformed domain. The relevance of measuring in the time domain is discussed, demonstrating improved accuracy over wavelength shift and inverse spatial domain methods. Several sensors with different internal diameters underwent cycles of transverse deformation, revealing robust linear trends in every case. On average, the structure demonstrated elastic behavior under deformations up to 42 μm, with a mean sensitivity of 0.174 rad/μm, and mechanical breakage taking place at 58 μm. The results confirmed the suitability of the sensor to withstand uniaxial micro-displacements or pressures, with smaller inner diameter capillary fibers showing the best performance., This work was supported in part by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe" under Project PID2019-107270RB-C22 and Project PID2022-137269OB-C21, in part by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR under Project PDC2021-121172-C21 and Project TED2021- 130378B-C22, and in part by the Public University of Navarre under Project PJUPNA06-2022. Open access funding provided by Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Rayleigh signature interrogation in time-domain DAS sensors using the short-frequency Fourier transform

  • Sharif, Vahid
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We present a general method to determine the dependence of Rayleigh backreflection in an optical fiber on position and optical frequency. It is based on applying the so-called short-frequency Fourier transform to signals obtained from coherent optical time-domain reflectometry (COTDR) measurements. The proposed method enables the implementation of distributed acoustic sensors (DAS) with high linearity, spatial resolution, and measurement frequency, while being immune to signal fading. Additionally, the technique is compatible with both conventional COTDR setups and those employing pulse compression, including phase-coded compression waveforms. We experimentally demonstrate the technique with DAS measurements of a 50-km sensing fiber, achieving a 2-m spatial resolution and a sensitivity of 137 p epsilon/root Hz using a pulse-compression COTDR with a P4 phase-coded compression waveform., Grant PID2022-137269OB-C21 funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way to make Europe. Grant TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union Next generationEU/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Remote power over fiber electro-mechanical modulation for enabling hybrid sensor networks

  • Rodríguez Rodríguez, Armando
  • López-Amo Sáinz, Manuel
  • Bravo Acha, Mikel
This work presents a power-efficient solution based on Power over Fiber technology that combines and enables the use of electronic devices in fiber optic networks. The optical carrier is modulated via a microelectromechanical variable optical attenuator, using the processed sensor data, which is encoded in a frequency shift keying technique. To illustrate the concept, a 50-km remote environmental station is powered by energy harvesting techniques to provide the requisite power, and a low-power microcontroller encodes the data from electronic sensors. The data was successfully retrieved, achieving data rates of up to 1.5 kbps., This work was supported in part by projects PID2022-137269OB-C21, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Power over fiber system for heterogeneous sensors multiplexing

  • Rodríguez Rodríguez, Armando
  • Vanegas Tenezaca, Evelyn Dayanara
  • Vento Álvarez, José Raúl
  • López-Amo Sáinz, Manuel
  • Bravo Acha, Mikel
This paper presents a Power-over-Fiber based remote electronic and optical fiber sensors multiplexing scheme. The system architecture consists of a 50-km linear cavity Raman-fiber laser that is used for interrogation of FBG optical fiber sensors. Simultaneously, electronic sensors information is modulated in amplitude while the optical sensors' data are encoded in the spectral information. In order to bias the electronic sensors, the residual power of the Raman pump laser is collected in an energy harvesting unit. This electric power is used for biasing an ATTiny85 control unit and two electro-optical modulators. A proof-of-concept is presented where a couple of optical fiber-Bragg-gratings sensors collect strain information that is self-compensated in temperature according to the digital data achieved from the electronic sensors. A 9.6 kbit/s data rate was achieved using Mach-Zehnder amplitude modulators and a maximum 35 ksample/s was retrieved using a high-speed C-band spectrometer and performing spectral analysis via a software developed in Python. Authors, This work was supported in part by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", under Project PID2022-137269OB-C21, in part by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR under Project TED2021-130378B-C22, and in part by MICINN under the Beatriz Galindo BEAGAL18/00116 Grant. Open access funding provided by Universidad Publica de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Frazão, Orlando
  • Silva, Susana
A paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration is demonstrated experimentally. The laser cavity has a fiber sensor at one end, that allows refractive index measurements. The refractometer consists of a cleaved fiber tip combined with an FBG functioning as a reflecting mirror. The combination of a fiber loop mirror at the other end allows to reflect all the light from the FBG and refractometer, forming a linear cavity. By measuring the intensity variation of the Fresnel reflection at the fiber-to-liquid interface, the measured concentration is linear and have a concentration sensitivity of -8.74±0.34×10-5 µW/(g/kg), over a range of 52.61 to 219.25 g/kg, and with a resolution of 2.77 g/kg. The results obtained present high stability and prove the potential of the fiber laser system to performed real-time measurements of concentration, in a non-invasive way., This research was funded by: National Funds through the Portuguese funding agency, FCT - Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020 and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/ AEI/https://doi.org/10.13039/501100011033 and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Urban water leakage detection system over dark fiber networks based on distributed acoustic sensing and sparse autoencoders

  • Sharif, Vahid
  • Yao, Yuanyuan
  • Loayssa Lara, Alayn
  • Sagüés García, Mikel
We propose and experimentally validate an automatic urban water leakage detection architecture that leverages dark fiber links already deployed in telecommunication networks in underground conduits in the vicinity of water pipelines. The sensing stage relies on a differential-phase coherent optical time-domain reflectometry interrogator enhanced with optical pulse compression to improve sensitivity. Building on this vibration acquisition stage, automatic leakage detection algorithms are implemented by searching for leak-induced activity in the frequency domain, which is well suited to revealing leakage-related features. After acquiring a baseline calibration to characterize normal-condition vibrations at each sensing position, leakage candidates are identified by comparing distribution-based metrics computed over multiple measurements against the corresponding baseline statistics. Two automatic leakage detection strategies are developed. First, low-complexity feature-based metrics are implemented, enabling continuous monitoring with minimal computational requirements. Second, an autoencoder-based anomaly detection technique is introduced, which also relies on location-specific normal-condition calibration but reduces the dependence on prior knowledge of the expected leakage vibration signatures. A real-world field trial on an urban network demonstrates reliable detection and localization using controlled leak events generated in the field, with measurements performed over a 17 km sensing fiber and an effective spatial resolution of 2.6 m. Benchmarking against a commercial punctual electro-acoustic leak detector yields consistent trends. Overall, the proposed system could complement existing technologies by enabling automated, continuous city-scale monitoring over already deployed dark fiber infrastructure., This work was supported in part by grant PID2022-137269OB-C21 funded by MCIN/AEI/10.13039/501100011033, ERDF “A way to make Europe”, and by grant TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generationEU”/PRTR, and the China Scholarship Council (CSC). Open accessfunding was provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Time-transformed spectral analysis for multiparametric sensing using a single antiresonant interferometer

  • Jaso Gallego, Isabel
  • Sánchez González, Arturo
  • Bravo Acha, Mikel
  • Pérez Herrera, Rosa Ana
  • Leandro González, Daniel
This work explores the potential of spectral composition analysis in the time-transformed domain for multiparametric sensing using a single in-line hollow-core interferometer. By effectively distinguishing between antiresonance guidance and Fabry Perot-induced contributions, this approach allows simultaneous measurement of two independent parameters. The sensor, featuring polyimide coating, was characterized during humidity cycles at varying temperatures by monitoring phase variations in the transformed domain. The distinct sensitivities of antiresonance and Fabry-Perot components allowed the determination of temperature and relative humidity using a multiparametric linear model, achieving good agreement with experimental results and underscoring its robustness for multiparametric sensing applications., This work was supported in part by projects PID2019-107270RB-C22, PID2022-137269OB-C21 funded by MCIN/AEI/10.13039/501100011033 and FEDER 'A way to make Europe', projects PDC2021-121172-C21, TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union 'Next generation EU'/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

General method for Rayleigh signature interrogation in distributed acoustic sensors based on optical time-domain reflectometry

  • Sharif, Vahid
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a method to measure the Rayleigh signature of an optical fiber, which is defined as the frequency dependence of the backscattering from each position along its length. The method uses the Short-Frequency Fourier transform to extract frequency-dependent time-resolved information from the spectrum of the detected pulse response in an optical time-domain reflectometry (OTDR) setup. The Rayleigh signature obtained can be used to implement broadband high-sensitivity high-linearity distributed acoustic sensors (DAS) that are immune to signal fading problems commonly affecting other OTDR-based systems. Rayleigh signature interrogation has been widely applied in optical frequency-domain reflectometry sensors and some specialized OTDR configurations. However, to our knowledge, this is the first technique that enables its general use in conventional single-pulse coherent OTDR setups, as well as in other time-domain systems that measure the impulse response of a fiber, such as those that utilize pulse compression. We experimentally demonstrate the method in a conventional heterodyne-detection OTDR DAS and also in a enhanced-performance pulse compression setup employing phasecoded waveforms. Measurements in a 50 km fiber with spatial resolution 2 m and a sensitivity of 113 p/√Hz demonstrate the capabilities of the technique., publication 15 July 2025; date of current version 16 September 2025. This work was supported in part by Grant PID2022-137269OBC21 funded by MCIN/AEI/10.13039/501100011033 and by ERDF “A way to make Europe”, in part by Grant TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generationEU”/PRTR. Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Quasi-distributed 3-cm vibration and strain monitoring using OFDR and in-line interferometers

  • Sánchez González, Arturo
  • Leandro González, Daniel
  • Shi, Muyu
  • Zhu, Mengshi
  • Murayama, Hideaki
Fecha de publicación: 2024-06-21, This study presents a new quasi-distributed vibration sensing approach with a 3-cm spatial resolution, capable of performing multiparameter measurements. In-line interferometers are employed simultaneously as strain point sensors and reflectors for vibration monitoring due to the Doppler effect. The interferometers consist of capillary fiber segments spliced between single-mode fibers, forming a sensing etalon. A study of the characteristics required for the fiber array fabrication is carried out. A 60 cm array comprising 20 sensing sections is used for the proof-of-concept of the technique for strain and vibration sensing. An analysis of the behavior for static strain and vibrations is performed, both individually and simultaneously, using a free-end cantilever experiment., This work was supported in part by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", under Project PID2022-137269OB-C21, in part by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR, under Project TED2021-130378B-C22, and in part by the Science and Technology Commission of Shanghai Municipality, China under Grant 23002400300. Open access funding provided by Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Urban water leakage detection system based on distributed acoustic sensing over dark fiber networks

  • Sharif, Vahid
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
A novel system for automatically detecting leaks in urban water supply networks is proposed and experimentally demonstrated in a real-world scenario. It leverages the extensive fiber optic access network infrastructure already available., Funding Grant PID2022-137269OB-C21 funded by MCIN/AEI/10.13039/501100011033 and by ERDF 'A way to make Europe'. Grant TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union 'Next generationEU' PRTR. Special thanks to ANIMSA S.A.U and Mancomunidad de la Comarca de Pamplona for their support by giving access to the dark fiber and the water supply network.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Tesis doctoral (DoctoralThesis)

Development of point optical fiber sensor systems for applications in smart cities, Desarrollo de sistemas de sensores puntuales de fibra óptica para aplicaciones en ciudades inteligentes

  • Rodríguez Rodríguez, Armando
La tecnología de fibra óptica ha avanzado significativamente en las últimas décadas debido a su rendimiento superior en aplicaciones de comunicación. Basándose en estas innovaciones científicas y tecnológicas, los sensores de fibra óptica (FOS) han surgido como soluciones versátiles a muchas limitaciones de las tecnologías de detección tradicionales. Por ejemplo, los sensores de fibra óptica son químicamente inertes y resistentes a la interferencia electromagnética, lo que los hace ideales para su uso en entornos peligrosos. Además de estos beneficios, los sensores de fibra óptica tienen otras características deseables, como bajo ruido de señal, diseño ligero y compacidad. Estas cualidades únicas han hecho posible su implementación en varias aplicaciones, siendo las que han mostrado mayor éxito, las tecnologías basadas en mecanismos interferométricos, de retrodispersión y de redes de difracción de Bragg (FBGs). Las estrategias de detección por fibra óptica utilizan diversos mecanismos de transductores y métodos de multiplexación. Sin embargo, se necesitan mejoras, principalmente debido al alto coste de los sensores de fibra en comparación con las tecnologías establecidas. Por lo tanto, las técnicas de multiplexación son esenciales para reducir los costes por sensor. Elegir un enfoque de multiplexación depende del tipo específico de sensor y de los requisitos de la aplicación. Por ejemplo, las redes de difracción de Bragg funcionan bien con la multiplexación por división de longitud de onda, mientras que los sensores interferométricos requieren métodos más complejos. Aunque el coste es una preocupación principal, el rendimiento y la versatilidad también deben ser considerados para una solución óptima. El progreso de las Ciudades Inteligentes requiere tecnologías de sensores innovadoras que puedan abordar las complejidades de los sistemas urbanos modernos con precisión, eficiencia y escalabilidad. En este sentido, esta tesis pretende contribuir con nuevas soluciones de sensores de fibra óptica puntuales. Incluye la incorporación de redes de difracción de Bragg y fibras ópticas microestructuradas, desplegando métodos de multiplexación híbridos para redes de sensores escalables, e implementando la tecnología Power over Fiber para facilitar el suministro remoto de energía y la interrogación eficiente de redes de sensores heterogéneas. Estas estructuras pueden adaptarse para aplicaciones tales como la medición de parámetros ambientales y el monitoreo de la calidad del agua y la salud estructural. El trabajo desarrollado durante esta tesis ha sido realizado en el grupo de investigación de Comunicaciones Ópticas y Aplicaciones Electrónicas de la Universidad Pública de Navarra (UPNA) bajo el Programa de Doctorado en “Tecnologías de la Comunicación, Bioingeniería y Energías Renovables” para el Grado de Doctor en Ingeniería de Telecomunicación. Además, este trabajo se ha desarrollado en parte durante una estancia de investigación en la Universidade de Aveiro (Portugal) bajo la supervisión del Prof. Dr. Carlos Marques., Fiber optic technology has advanced significantly in recent decades due to its superior performance in communication applications. Building on these scientific and technological innovations, fiber optic sensors (FOS) have emerged as versatile solutions to many limitations of traditional sensing technologies. For instance, fiber optic sensors are chemically inert and resistant to electromagnetic interference, making them ideal for use in hazardous environments. In addition to these benefits, fiber optic sensors have other desirable features, including low signal noise, a lightweight design, and compactness. These unique qualities have enabled their deployment in several applications, with technologies based on interferometric mechanisms, backscattering, and Fiber Bragg Gratings (FBGs) showing the most success. Several fiber optic sensing strategies use various transducer mechanisms and multiplexing methods. However, improvements are needed, primarily due to the high cost of fiber sensors compared to established technologies. Thus, multiplexing techniques are essential for reducing the cost per sensor. Choosing a multiplexing approach depends on the specific sensor type and application requirements. For example, fiber Bragg gratings work well with wavelength division multiplexing, while interferometric sensors require more complex methods. Although cost is a primary concern, performance and versatility must also be considered for an optimal solution. The progress of Smart Cities requires innovative sensing technologies that can address the complexities of modern urban systems with precision, efficiency, and scalability. In this regard, this thesis aims to contribute to the development of new point optical fiber sensing solutions. It includes the incorporation of fiber Bragg gratings and microstructured optical fibers, deploying hybrid multiplexing methods for scalable sensor networks, and implementing Power over Fiber technology to facilitate remote power provision and efficient interrogation of heterogeneous sensor networks. These structures can be adapted for various applications, including measuring environmental parameters and monitoring water quality and structural integrity. The work developed during this thesis was conducted in the Optical Communication and Electronic Applications research group at Universidad Pública de Navarra (UPNA) under the Doctorate Program in “Communications Technologies, Bioengineering, and Renewable Energies” for the degree of Doctor of Philosophy (Ph.D.) in Telecommunication Engineering. Additionally, this work was developed in part during a research stay at the Department of Physics and I3N, Universidade de Aveiro, Aveiro, Portugal, under the supervision of Prof. Dr. Carlos Marques., Financial support received: Universidad Pública de Navarra (UPNA) through the pre-doctoral research grants, mobility grants, and complementary grants for doctoral theses; Research project PID2019-107270RB-C02 funded by the Spanish Government Ministerio de Ciencia e Innovación (MCIN)/Agencia Estatal de Investigación (AEI) and FEDER “A way to make Europe”; Research project PDC2021-121172-C01 funded by the Spanish Government MCIN/AEI and the European Union “Next generation EU” / Plan de Recuperación, Transformación y Resilencia (PRTR); Research project TED2021-130378B-C22 funded by the Spanish Government MCIN/AEI and the European Union “Next Generation EU” / PRTR and Research project PID2022-137269OB funded by the Spanish Government CIN/AEI and FEDER “A way to make Europe”., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa Ofiziala (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Microdisplacement sensor based on a processed optical fiber by an ultrafast laser-assisted etching method

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Gómez-Galdós, C.
  • López-Amo Sáinz, Manuel
  • López Higuera, José Miguel
  • Rodríguez Cobo, Luis
In this work, a fabrication technique for microchannel-based reflectors used as an optical fiber sensor is demonstrated by using a processed optical fiber by an ultrafast laser-assisted etching method. This microdisplacement sensor was experimentally demonstrated to have an outstanding resolution of 5.9 rad/μm in the measurement range from 0 to 80 microns, by using the fast Fourier transform (FFT) measuring method., This work was supported in part by projects PID2022-137269OB, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and TED2021-130378B funded by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR, and by the R+D project INNVAL23/10 financed by IDIVAL.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Capillary-based optical fiber sensor for turbidity measurement

  • Vanegas Tenezaca, Evelyn Dayanara
  • Galarza Galarza, Marko
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Cobo, Adolfo
  • López-Amo Sáinz, Manuel
This work introduces an innovative capillary or hollow core-based sensor designed to measure turbidity by using the reflection of light in its cladding. The structure consists of two different capillary sections and has been optimized to maximise the interaction of light with the external liquid. Experimentation includes data collection from different turbidity levels using the reflected spectrum. To improve the measuring results, machine learning is implemented, exploring the effectiveness of various algorithms and neural network architectures to achieve a good root mean square error., This work was supported in part by projects PID2022-137269OB, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Measurement of paracetamol concentration using an erbium-doped fiber ring cavity

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Silva, Susana
  • Frazão, Orlando
Process Analytical Technology (PAT) has been increasingly used in the pharmaceutical industry to monitor essential parameters in real-time during pharmaceutical processes. The concentration of Active Pharmaceutical Ingredients (APIs), such as paracetamol, is one of these parameters, and controlling its variations allows for optimization of the production process. In this study, a refractometric sensor, implemented by an interrogation system based on an Erbium-Doped Fiber Ring Cavity (EDFRC), was presented and experimentally demonstrated. The Cavity Ring proposed included a 1 × 3 coupler. One port of the coupler was used to increase the optical power of the system through a Fiber Bragg Grating (FBG), and the other two ports were used as sensing head and reference. The sensor detected variations of paracetamol concentration with a sensitivity of [(−1.00 ± 0.05) × 10−3] nW/(g/kg) and a resolution of 5.53 g/kg. The results demonstrate the potential of this technology as a possible non-invasive PAT tool., and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.This research was funded by: National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020, and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22, funded by MCIN/AEI/10.13039/501100011033