Pasar al contenido principal

DISPOSITIVOS Y SISTEMAS FOTONICOS SENSORES PARA ESTRUCTURAS INTELIGENTES Y EVALUACION NO DESTRUCTIVA II

PID2019-107270RB-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD PUBLICA DE NAVARRA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 40
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Linewidth on the Relative Intensity Noise in Random Distributed Feedback Raman Fiber Lasers

  • Rota-Rodrigo, S.
  • Leandro, D.
  • Santarelli, G.
  • López-Amo, Manuel
  • Ania Castañón, Juan Diego
Artículo con 5 figuras, We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz., This research was funded by the Spanish Government grants RTI2018-097957-B-C33, PID2021-128000OB-C21, and PID2019-107270RB-C22; Conseil Régional d’Aquitaine (2017-1R50302-00013493); LAPHIA (Lasers and Photonics in Aquitaine); the Horizon 2020 Framework Programme (H2020) (Marie Sklodowska-Curie—748839); and Comunidad de Madrid project SINFOTON2-CM (S2018-NMT/4326). Additional support was from AEI/FEDER funds.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cross Sections for Electron Scattering from Cadmium: Theory and Experiment

  • Marinković, B. P.
  • McEachran, R. P.
  • Fursa, D. V.
  • Bray, I.
  • Umer, H.
  • Blanco, F.
  • García, Gustavo
  • Brunger, M. J.
  • Campbell, L.
  • Jones, D. B.
12 pags., 5 figs. -- This paper is dedicated to Professor Michael Brunger, who coordinated the collaborative contributions, Results from the application of optical potential, relativistic optical potential, relativistic convergent close-coupling, and binary encounter Bethe models to electron scattering from gas-phase cadmium are presented. In particular, integral cross sections for elastic scattering, summed discrete electronic-state excitation, and ionization scattering processes are reported over an extended incident electron-energy range. Total cross sections are constructed by taking their sum. Measurements are presented for elastic scattering and for excitation to the 51P1 state. The theoretical and experimental results are compared to previous calculations and measurements. Recommended electron cross-section datasets are constructed over an incident electron energy range of 0.01-10 000 eV., This work was financially supported, in part, by the Australian Research Council (ARC) DP180101655, DP190100696, and DP220101480 projects; in part, by the Institute of Physics University Belgrade, through the grant by the Ministry of Education, Science and Technological Development of the Republic of Serbia (Grant No. 451-03-9/2021-14); in part, by the Spanish Ministry of Science and Innovation (Project Nos. PID2019-10727RB-C21 and C22); and, in part, by resources provided by the Pawsey Supercomputing Centre with funding from the Australian Government and the Government of Western Australia. D.B.J. is the recipient of an ARC Future Fellowship (Grant No. FT210100264) funded by the Australian Government., Peer reviewed
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Láser random de fibra óptica asistido por reflectores de fibra con retrodispersión controlada artificialmente, Optical fiber random laser assisted by artificially controlled backscattering fiber reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Galarza Galarza, Marko
  • Sañudo-Lasagabaster Ibáñez, Silvia
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
Este trabajo presenta un láser de fibra tipo random (LFR) en cavidad semi-abierta, mediante amplificación híbrida Raman-Erbio y asistida por reflectores de fibra con retrodispersión controlada artificialmente (RFRCA). Como medio activo se ha empleado una combinación de 2,4 km de fibra compensadora de dispersión con dos tramos de fibra altamente dopada con erbio de 5 m cada uno. Se ha obtenido una única línea de emisión láser centrada a en 1553.8 nm y con una relación señal a ruido óptica de 47 dB cuando en la estructura se inyectaba una potencia de bombeo de 37.5 dBm. Además, se ha medido la estabilidad en términos de potencia de salida de este láser durante 3 horas, obteniendo una inestabilidad tan baja como 0,08 dB con un nivel de confianza del 100%., This work shows a semi-open cavity random type fiber laser (RFL), using hybrid Raman- Erbium amplification and assisted by artificially controlled backscattering fiber reflectors (RFRCA). As active medium, a combination of 2.4 km of dispersion compensating fiber with two sections of highly erbium doped fiber of 5 m each has been used. A single random laser emission line centered at 1553.8 nm and with a signal-to-optical noise ratio of 47 dB was obtained when a pump power of 37.5 dBm was injected into the structure. In addition, the stability in terms of output power of this laser has been measured along 3 hours, obtaining an instability as low as 0.08 dB with a 100% confidence level., Este trabajo ha sido financiado por el Ministerio de Ciencia e Innovación y la Agencia Estatal de Investigación (PID2019-107270RB), fondos FEDER, el Ministerio de Educación, Cultura y Deporte de España (Beca FPU2018/02797), y los Proyectos de Jóvenes Investigadores de la UPNA 2019 (PJUPNA1928).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Erbium-doped fiber ring cavity for the measurement of refractive index variations

  • Pérez Herrera, Rosa Ana
  • Soares, Liliana
  • Novais, Susana
  • Frazão, Orlando
  • Silva, Susana
In this work, an erbium-doped fiber ring cavity based on a 3dB optical coupler for refractive index measurements is presented and experimentally verified. This interrogation system, based on a 1 x 2 optical coupler, uses one of these output ports to increase the reflected optical power by means of a fiber Bragg Grating (FBG), used as a reflector. Moreover, the other output port is used as a refractive index sensing head. A spectral analysis of this interrogator system as well as a fiber cavity ring refractive index sensor characterization are carried out. Finally, an experimental comparison of the refractive index sensor range when the 3dB coupler is replace by a 1x3 one is also presented., This work is financed by the program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Universidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR; and National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020 and FCT, Portugal through the Grant 2020.05297.BD
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Compensation of laser phase noise in coded distributed acoustic sensing

  • Piñeiro Ben, Enrique
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We demonstrate, for the first time to our knowledge, a technique for the compensation of phase noise effects in coded pulse compression DAS and compare its performance to systems using frequency-modulated pulse compression., PID2019-107270RB-C22/AEI/10.13039/501100011033. PID2022-137269OB-C21/AEI.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Aluminum coated fiber optic sensor for enhancing flow rate measurement

  • Rodríguez Rodríguez, Armando
  • Urroz Unzueta, José Carlos
  • Diéguez Elizondo, Pedro
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
  • López Rodríguez, José Javier
A water flow and velocity aluminum-coated Fiber Bragg Grating sensor system for open channels was designed, simulated and tested. The sensing head was designed, ruggedized and customized to measure velocities at different depths, in order to calculate the discharge in open channels. This paper shows, for the first time to our knowledge, the simulation of such kind of fiber sensors in open channels., This work was supported in part by projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Compensation of phase noise impairments in distributed acoustic sensors based on optical pulse compression time-domain reflectometry

  • Piñeiro Ben, Enrique
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a method to compensate for the deleterious effects of the phase noise of the laser source on long-range distributed acoustic sensors (DAS) that implement optical pulse compression (OPC). Pulse compression can be used in coherent optical time-domain reflectometry (COTDR) sensors to extend the measurement range without compromising spatial resolution. In fact, OPC-COTDR sensors have demonstrated the longest measurement range to date in passive sensing links that do not require distributed amplification to compensate fiber attenuation. However, it has been found that the limited coherence of the laser source has a degrading effect on the actual performance enhancement that pulse compression can bring because it constrains the maximum duration of the compression waveforms that can be used and makes the use of lasers with extremely low phase noise necessary.We introduce a technique to compensate for the effects of phase noise on OPC-COTDR sensors so that they can demonstrate their full potential for long-range measurements using lasers with less stringent phase noise requirements. The method is based on sampling the phase noise of the laser with an auxiliary interferometer and using this information in a simple signal processing technique to mitigate its deleterious effect on the signal measured. We test our method in an OPCCOTDR sensor that uses 500-μs linear frequency modulated pulses to demonstrate 100-km range measurements with 200 p/√Hz of strain sensitivity at 2-m initial spatial resolution that becomes 10-m after applying the gauge length. To our knowledge, this is the longest compression waveform demonstrated to date in an OPCCOTDR sensor. Its use provides an extra 20-km range compared to previous demonstrations using laser sources of comparable linewidth. Furthermore, comparable performance is also demonstrated when using a laser source with an order of magnitude larger linewidth., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER “A way to make Europe” and MCIN/AEI/10.13039/501100011033 under Grant PID2019-107270RB-C22, and in part by the Gobierno de Navarra under Grant PC210-211 FIBRATRAFIC.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

C and L band fiber lasers enhanced by ultrafast laser inscribed artificial backscatter reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
This letter presents an experimental comparison between two linear-cavity erbiumdoped fiber lasers (EDFL) assisted by two different artificial backscatter fiber-based reflectors. Both reflectors were inscribed by femtosecond laser direct writing, one of them within a single-mode fiber (SMF) and the other one within a multi-mode fiber (MMF). Although the erbium-doped fiber amplifier (EDFA) used in both structures was the same and both reflectors were manufactured under the same parameters, the reflection spectrum of each was clearly different due to their different physical properties. The first linear-cavity EDFL, consisting of an SMF-based reflector with 9µm core and 125µm cladding, resulted in a single laser emission line located in the C-band and centered at 1564.4 nm, exhibiting an optical signal-to-noise ratio (OSNR) of 52dB when pumped at 100mW. On the other hand, a single laser emission line with a similar OSNR but in L-band (centered at 1574.5nm) was obtained when using an MMF-based reflector with 50µm core and 125µm cladding., Ministerio de Educacion, Cultura y Deporte (PhD grant FPU2018/02797); European Commission (Next generation EU/PTR); FEDER (A way to make Europe); MCIN/AEI/10.13039/501100011033 (PDC2021-121172-C21, PID2019-107270RB).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Micro-displacement sensor based on hollow core fiber interferometers

  • Sánchez González, Arturo
  • Rodríguez Rodríguez, Armando
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Pérez Herrera, Rosa Ana
  • López-Amo Sáinz, Manuel
An interferometric sensor based on hollow core fibers for the measurement of micro-displacement has been designed. Its characterization has resulted in a linear response, suggesting its application in pressure sensors., This work is part of the projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and PDC2021-121172-C01 funded by MCIN/ AEI/10.13039/501100011033 and European Union "Next generationEU"/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Medida de torsión en seguidores solares con sensores de fibra óptica, Torsion measurements on solar trackers using fiber optic sensors

  • Leandro González, Daniel
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
  • Loayssa Lara, Alayn
  • Júdez Colorado, Aitor
  • Mariñelarena Ollacarizqueta, Jon
  • Falcone Lanas, Francisco
  • Jiménez Romero, Sergio
  • Moriana García, Iñaki
En este trabajo se ha monitorizado la torsión sufrida por una estructura de seguidores solares empleando sensores de fibra óptica. Estas medidas de campo se han obtenido con una red de sensores formada por 45 redes de difracción de Bragg en una huerta solar activa. Estos resultados, correlados con la velocidad y dirección del viento permitirían aumentar la eficiencia de los seguidores y ayudar a entender y prevenir efectos negativos relacionados con inestabilidades aeroelásticas., In this work, the torsion experienced by set of solar trackers is monitored using fiber optic sensors. The in-field measurements were obtained using a sensor network comprising 45 fiber Bragg gratings in an active solar plant. These results, correlated with wind speed and direction could increase efficiency and lead to understand and prevent harmful effects related to aeroelastic instability events., Este trabajo ha sido financiado por el proyecto WINDSOLAR (0011-1365-2017-000122) del Gobierno de Navarra, los proyectos TEC2016-76021-C2 y PID2019-107270RB-C22, los fondos FEDER, la European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 838143 y las fundaciones 'Caja Navarra' y 'la Caixa' con el proyecto LCF/PR/PR13/51080004.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Development of a water flow and velocity optical fiber sensor for field testing

  • Rodríguez Rodríguez, Armando
  • Urroz Unzueta, José Carlos
  • Diéguez Elizondo, Pedro
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
  • López Rodríguez, José Javier
A water flow and velocity fiber optic sensor system was developed and tested. The sensing head was especially developed and ruggedized to measure velocities at different depths, in order to calculate the discharge in channels., This work is part of the projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and PDC2021-121172-C01 funded by MCIN/ AEI/10.13039/501100011033 and European Union "Next generation EU"/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Tesis doctoral (DoctoralThesis)

Desarrollo de láseres de fibra óptica con aplicación en sistemas de sensores, Development of optical fiber lasers for sensing applications

  • Sánchez González, Arturo
Esta tesis presenta el desarrollo y análisis de distintas tecnologías fotónicas basadas en fibra óptica para la monitorización de magnitudes físicas, con énfasis en configuraciones tanto puntuales como cuasidistribuidas. El trabajo se organiza en torno a tres bloques principales que abordan, de forma progresiva, desde el diseño de fuentes láser hasta técnicas avanzadas de interrogación y monitorización estructural. El primer bloque se centra en el estudio de láseres aleatorios de fibra óptica coherentes, fabricados a partir de reflectores pseudoaleatorios inscritos mediante láser de femtosegundo. Se desarrollan diferentes configuraciones orientadas a mejorar la estabilidad espectral, lograr operación en modo longitudinal único y extender la emisión a bandas C y L. Asimismo, se analiza su funcionalidad como sensores multiparamétricos, destacando su capacidad para la discriminación simultánea de temperatura y deformación mediante fuentes multilínea. El segundo bloque examina sensores ópticos interferométricos construidos con fibras de núcleo hueco, en los que se propone una estrategia alternativa de interrogación basada en la transformación espectral al dominio temporal. Este enfoque permite descomponer interferogramas complejos, mejorar la resolución de medida y facilitar la identificación precisa de los mecanismos físicos subyacentes. La técnica se valida experimentalmente en la medición de deformación transversal, demostrando su viabilidad para aplicaciones de caracterización multiparamétrica. El tercer bloque introduce una estrategia cuasidistribuida de monitorización mediante reflectometría óptica en el dominio de la frecuencia. A través de una catenaria de reflectores interferométricos y un modelo analítico detallado, se logra la detección simultánea de vibraciones espectralmente complejas y deformaciones longitudinales, con mejoras en resolución y tiempos de respuesta frente a otras tipologías de esquemas distribuidos basados en retrodispersión Rayleigh. Esta arquitectura se plantea como una solución escalable para aplicaciones de diagnóstico estructural de precisión. En conjunto, la tesis proporciona una base técnica y metodológica para el desarrollo de sistemas fotónicos de monitorización física, abordando tanto aspectos estructurales de los dispositivos como estrategias de interrogación y procesamiento de señal. Los resultados permiten identificar nuevas vías de avance en el diseño de láseres y sensores compactos, estables y adaptables a diferentes entornos operativos., This thesis presents the development and analysis of various photonic technologies based on optical fiber for the monitoring of physical parameters, with an emphasis on both point and quasi-distributed configurations. The work is organized into three main sections that progressively address topics ranging from the design of laser sources to advanced interrogation techniques and structural monitoring. The first section focuses on the study of coherent random fiber lasers, fabricated using pseudo-random reflectors inscribed by femtosecond laser. Several configurations are developed with the aim of improving spectral stability, achieving single longitudinal mode operation, and extending emission to the C and L bands. Additionally, their functionality as multiparametric sensors is analyzed, highlighting their ability to simultaneously discriminate between temperature and strain through multi-line sources. The second section examines interferometric optical sensors constructed with hollow-core fibers, proposing an alternative interrogation strategy based on spectral-to-temporal domain transformation. This approach enables the decomposition of complex interferograms, enhances measurement resolution, and facilitates the precise identification of underlying physical mechanisms. The technique is experimentally validated in the measurement of transverse strain, demonstrating its feasibility for multiparametric characterization applications. The third section introduces a quasi-distributed monitoring strategy using frequency-domain optical reflectometry. Through a catenary of interferometric reflectors and a detailed analytical model, simultaneous detection of spectrally complex vibrations and longitudinal strains is enabled, with improved resolution and response times compared to other distributed schemes based on Rayleigh backscattering. This architecture is proposed as a scalable solution for precision structural diagnostics. Overall, the thesis provides a technical and methodological foundation for the development of photonic systems for physical monitoring, addressing both structural aspects of the devices and strategies for interrogation and signal processing. The results make it possible to identify new avenues for advancement in the design of compact, stable, and adaptable lasers and sensors for various operational environments., Financiado por Universidad Pública de Navarra mediante los «Contratos predoctorales UPNA 2020/2021»(Resolución 989/2020), Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación (AEI) mediante el proyecto «Dispositivos y Sistemas Fotónicos Sensores para estructuras inteligentes y evaluación no destructiva II»(PID2019-107270RB-C22), Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación (AEI), Unión Europea NextGenerationEU/PRTR mediante el proyecto «Sistema integrado para la monitorización de tráfico y mantenimiento de carreteras usando sensores de fibra óptica I»(PDC2021-121172-C21) y Fondo Europeo de Desarrollo Regional, Agencia Estatal de Investigación (AEI) mediante el proyecto «Sensores fotónicos para ciudades inteligentes y sostenibles I»(PID2022-137269OB-C21)., Programa de Doctorado en Tecnologías de las Comunicaciones, Bioingeniería y de las Energías Renovables (RD 99/2011), Bioingeniaritzako eta Komunikazioen eta Energia Berriztagarrien Teknologietako Doktoretza Programa Ofiziala (ED 99/2011)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Measurement of paracetamol concentration using a fiber laser system

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Frazão, Orlando
  • Silva, Susana
A linear fiber laser system for measurements of paracetamol concentration is experimentally demonstrated. The cavity is based on a fiber loop mirror and an FBG centered at 1567.8 nm. The sensing head corresponds to a refractometric sensor, whose which principle of operation is based on Fresnel reflection in the fiber tip (FBG side). The system works at detected variations of paracetamol concentrations with a sensitivity of [8.74± 0.34)× 10-5] µW/(g/kg) and a resolution of 2.77 g/kg. The results prove that the fiber laser system could be an asset for processing industries, specifically for non-invasive and real-time measurements of concentration., This work was financially supported by the Wellcome Trust, UK, through the Innovator Award “Light-activated cap for catheter sterilization” (WT223940/Z/21/Z); National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020 and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021- 130378B-C22 funded by MCIN/ AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

One-year analysis of road condition using FBG arrays

  • Corera Orzanco, Íñigo
  • Pradas Martínez, Javier
  • Leandro González, Daniel
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
In this work, it is presented an analysis of FBG arrays installed in a public road. The arrays were installed in a newly paved urban road and were monitored for more than one year. The study evidences the permanent deformation of the wearing course and the degradation of the reflected spectra of the sensors., This work is part of the projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and PDC2021-121172-C01 funded by MCIN/ AEI/10.13039/501100011033 and European Union “Next generationEU”/PTR and the project PJUPNA06-2022 from the Public University of Navarre and the Beatriz Galindo BEAGAL18/00116 grant funded by MICINN.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Cavidad láser de fibra óptica multibanda basada en reflectores pseudoaleatorios cuasidistribuidos

  • Sánchez González, Arturo
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
Trabajo presentado a la XIII Reunión Nacional de Óptica, 22-24 Noviembre 2021, En este trabajo se presenta un análisis experimental de las prestaciones alcanzadas por una cavidad láser en línea asistida por un reflector de fibra con retrodispersión controlada artificialmente (RFRCA). Dicho reflector ha sido concebido para permitir oscilación en un único modo longitudinal (SLM) en bandas C y L, presentando inestabilidades en potencia de emisión inferiores a 0.1 dB y relaciones de señal óptica a ruido (OSNR) superiores a 44 dB., Trabajo financiado por MICINN y AEI (PID2019-107270RB); fondos FEDER; MECD (Beca PFU 2018/02797); y los Proyectos de Jóvenes Investigadores de la UPNA 2019 (PJUPNA1928).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Long-range and high-resolution traffic monitoring based on pulse-compression DAS and advanced vehicle tracking algorithm

  • Corera Orzanco, Íñigo
  • Piñeiro Ben, Enrique
  • Navallas Irujo, Javier
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We demonstrate traffic monitoring over tens of kilometres of road using an enhanced distributed acoustic sensing system based on optical pulse compression and a novel transformed-domain-based processing scheme with enhanced vehicle detection and tracking capabilities., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER ”A way to make Europe” and MCIN/AEI/10.13039/501100011033 under grant PID2019-107270RB, and in part by Gobierno de Navarra under grant PC210-211 FIBRATRAFIC. The authors would like to thank Gobierno de Navarra and NASERTIC S.A.U for their support by giving access to the dark fiber deployed in this work.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Wavelength-switchable L-band fiber laser assisted by random reflectors

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
A wavelength-switchable L-band erbium-doped fiber laser (EDFL) assisted by an artificially controlled backscattering (ACB) fiber reflector is here presented. This random reflector was inscribed by femtosecond (fs) laser direct writing on the axial axis of a multimode fiber with 50 lm core and 125 lm cladding with a length of 17 mm. This microstructure was placed inside a surgical syringe to be positioned in the center of a high-precision rotation mount to accurately control its angle of rotation. Only by rotating this mount, three different output spectra were obtained: a single wavelength lasing centered at 1574.75 nm, a dual wavelength lasing centered at 1574.75 nm and 1575.75 nm, and a single wavelength lasing centered at 1575.5 nm. All of them showed an optical signal-to-noise ratio (OSNR) of around 60 dB when pumped at 300 mW, This work was financed by the program "José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores", funded by the Ministerio de Universidades of Spain (reference CAS21/00351); the Spanish AEI projects PID2019-107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe", and projects PDC2021-121172 and TED2021-130378B funded by MCIN/ AEI/10.13039/501100011033 and European Union "Next generation EU"/PTR. Finally, the work was also founded by the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Diseño y caracterización de reflectores incoherentes de retrodispersión de fibra microperforada para láseres random de fibra óptica, Design and characterization of incoherent backscattering microdrilled fiber reflectors for random fiber optic lasers

  • Galarza Galarza, Marko
  • Sañudo-Lasagabaster Ibáñez, Silvia
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
Los láseres random de fibra óptica presentan una serie de características que los hacen idóneos para una gran variedad de aplicaciones industriales. La elevada longitud de fibra necesaria en la cavidad debido a sus bajos índices de dispersión Rayleigh, se reduce utilizando fibras de baja área efectiva (compensadoras de dispersión), o generando artificialmente elementos muy dispersivos. En este trabajo presentamos el diseño de reflectores aleatorios de tan solo varios milímetros, generados mediante microperforación del núcleo con un láser de femtosegundo y su utilización en la cavidad de una estructura láser., Random fiber lasers show very interesting features for many industrial applications. The length of the fiber needed in the cavity reaches several tenths of kilometers due to the low Rayleigh dispersion coefficient. Using dispersion compensating fibers (fibers with small effective area) reduces this length, as well as using artificially generated dispersive elements. We present the design of random reflectors generated using a femtosecond laser to create the defects, which are only several millimeters long. The reflectors are used in a fiber laser structures and measured., Este trabajo ha sido financiado por el Ministerio de Ciencia e Innovación y la Agencia Estatal de Investigación (PID2019-107270RB), fondos FEDER, el Ministerio de Educación, Cultura y Deporte de España (Beca FPU2018/02797), y los Proyectos de Jóvenes Investigadores de la UPNA 2019 (PJUPNA1928).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Design of optical fiber Bragg grating-based sensors for flow measurement in pipes

  • Diéguez Elizondo, Pedro
  • Rodríguez Rodríguez, Armando
  • Urroz Unzueta, José Carlos
  • López Rodríguez, José Javier
  • López-Amo Sáinz, Manuel
In this work, optical Fiber Bragg grating (FBG) sensors were used to measure water flow in pipes. Several types of coatings were incorporated into the design of the sensors to examine their effects on the elastic strain that the fiber underwent as a result of the water flow. ANSYS-CFX V2020 R2 software was used to model the elastic strain encountered by the fiber under various flow rates in order to assess the performance of the FBG sensors. The calculations and experimental data exhibited good convergence, demonstrating the accuracy of the FBG sensors in determining water flow. These calculations and procedures can be extrapolated to any other fluid., This work was supported in part by projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Multiparameter sensor based on a multiinterferometric serial configuration for temperature and strain measurements

  • Pérez Herrera, Rosa Ana
  • Bravo Acha, Mikel
  • Leandro González, Daniel
  • Novais, Susana
  • Pradas Martínez, Javier
  • López-Amo Sáinz, Manuel
In this work, a multi-parameter point sensor based on the combination of Fabry-Perot (FP) and the anti-resonant (AR) reflecting guidance in cascade configuration is proposed and experimentally demonstrated. This structure, based on FP interference and AR reflecting guidance, was fabricated with two different air micro-cavities. The attained experimental results showed different strain and temperature sensitivities for the antiresonance contribution. However, when analyzing the FP interference, only strain sensitivity was observed, demonstrating that this air micro-cavity was also insensitive to temperature variations., This work was supported by the Spanish AEI projects TEC2016-76021-C2 and PID2019-107270RB-C22, FEDER Funds, the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 838143, Projects for young researches UPNA 2019, “Caja Navarra” and “la Caixa” foundations under agreement LCF/PR/PR13/51080004 and the grant BGP18/00180 of the “Beatriz Galindo” programme from the Spanish Ministry of Science, Innovation and Universities.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Multicore fiber sensors for strain measurement towards traffic monitoring

  • Sánchez González, Arturo
  • Pradas Martínez, Javier
  • Corera Orzanco, Íñigo
  • Bravo Acha, Mikel
  • Leandro González, Daniel
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Pérez Herrera, Rosa Ana
  • López-Amo Sáinz, Manuel
In this work, two new interferometric sensors based on multicore optical fibers for the measurement of strain with the ultimate goal of traffic monitoring are presented. The operating principle of each sensor relied on the monitoring of the phase shift difference accumulated between the supermodes of the structure of the multicore segment in a full round trip. The strain characterization for both sensors resulted in a linear response, with sensitivities of -4.073·10-3 rad/με and - 4.389·10-3 rad/με for the aligned and V-shaped cases respectively, and one-hour instabilities below 4.6·10-3 rad with a 95% confidence level. These results suggest its feasibility in applications requiring high sensitivities over very wide strain ranges, such as heavy-vehicle traffic monitoring. To corroborate the hypothesis, both sensors were integrated into the pavement and their response to the traffic was analyzed., This work is part of the projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, and PDC2021-121172-C01 funded by MCIN/ AEI/10.13039/501100011033 and European Union “Next generationEU”/PTR and the project PJUPNA06-2022 from the Public University of Navarre and the Beatriz Galindo BEAGAL18/00116 grant funded by MICINN.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Ring cavity erbium-doped fiber for refractive index measurements

  • Pérez Herrera, Rosa Ana
  • Soares, Liliana
  • Silva, Susana
  • Frazão, Orlando
In this study, an interrogation system based on an erbium-doped fiber ring cavity for refractive index measurements is presented and experimentally demonstrated. This cavity ring includes a 1 × 3 coupler wherein one of the fiber output ports is used to increase the optical power of the system by means of an FBG used as a reflector. The other two output ports are used as a refractive index sensing head and reference port, respectively. An experimental demonstration of this proposed sensor system for the measurement of a distinct refractive index is presented., This work is financed by the program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Universidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR; and National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020. Liliana Soares acknowledges the support of FCT, Portugal through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Sistema de interrogación multi-sensor basado en multiplexación en longitud de onda y tiempo, Multi-sensor interrogation system based on wavelength and time multiplexing

  • Bravo Acha, Mikel
  • Leandro González, Daniel
  • Pérez González, Asier
  • López-Amo Sáinz, Manuel
En este trabajo se propone un sistema de interrogación versátil y económico basada en la generación de pulsos empleando la modulación directa de diodos láser DFB. Se ha demostrado una resolución en longitud de onda de 1 pm para una separación de sensores de 600m. La validación del interrogador se ha llevado a cabo monitorizando una red de sensores de 26 km de longitud que incluye redes de difracción de Bragg, reflectores y un interferómetro Fabry-Pérot., This work proposes a versatile and cost-effective interrogation system based on pulses generation using direct modulated DFB laser diodes. A wavelength resolution of 1 pm is demonstrated for a 600 m sensor-spacing. A 26 km-long sensor network including fiber Bragg gratings, wideband reflectors and a Fabry-Pérot interferometer is used to validate the interrogator., Este trabajo ha sido financiado por los proyectos TEC2016-76021-C2 y PID2019-107270RB-C22, los fondos FEDER, la European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 838143, el contrato Beatriz Galindo BEAGAL18/00116 y las fundaciones 'Caja Navarra' y 'la Caixa' con el proyecto LCF/PR/PR13/51080004.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High frequency vibration sensor using a fiber laser with a multicore fiber interferometer

  • Correa Serrano, Ángel Ignacio
  • Galarza Galarza, Marko
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • López-Amo Sáinz, Manuel
  • Pérez Herrera, Rosa Ana
We present an interferometric vibration sensor that uses three-core fibers. The transducer is constructed by splicing a segment 20 mm long of a multicore optical fiber (MCF) to a single-mode optical fiber (SMF). The end of the MCF segment is cut off and painted using silver metallic paint. The sensor head is operated in reflection mode. The structure is placed on a polyvinyl chloride (PVC) plate, which is excited with a wide range of frequency signals. The vibrations induce cyclic bending in the MCF segment, resulting in periodic oscillations of the reflected interference spectrum. This device is demonstrated to be suitable to measure vibrations in a frequency range of the order of 300 kHz detecting deformations as small as 0.40μm ., This work was supported in part by projects PID2019-107270RB-C02 and PID2022- 137269OB-C21, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe,” and TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Quasi-distributed vibration analysis of a cantilever beam using OFDR and weak reflectors

  • Leandro González, Daniel
  • Zhu, Mengshi
  • Wada, Daichi
  • Kasai, Tokio
  • Igawa, Hirotaka
  • López-Amo Sáinz, Manuel
  • Murayama, Hideaki
This work evaluates the performance of a quasi-distributed in-line velocimeter based on OFDR and weak reflectors to measure vibration every 10 cm, using a cantilever beam under free-end damping and during an impact-hammer test., The project leading to these results has received funding from “la Caixa” Foundation, under agreement CF/PR/PR13/51080004 and from the project PID2019-107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Microdrilled tapers to enhance optical fiber lasers for sensing

  • Pérez Herrera, Rosa Ana
  • Bravo Acha, Mikel
  • Roldán Varona, Pablo
  • Leandro González, Daniel
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
In this work, an experimental analysis of the performance of different types of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror is presented. These artificially-controlled backscattering fiber reflectors are used in short linear cavity fiber lasers. In particular, laser emission and sensor application features are analyzed when employing optical tapered fibers, micro-drilled optical fibers and 50 μm-waist or 100 μm-waist micro-drilled tapered fibers (MDTF). Single-wavelength laser with an output power level of about 8.2 dBm and an optical signal-to-noise ratio of 45 dB were measured when employing a 50 μm-waist micro-drilled tapered optical fiber. The achieved temperature sensitivities were similar to those of FBGs; however, the strain sensitivity improved more than one order of magnitude in comparison with FBG sensors, attaining slope sensitivities as good as 18.1 pm/με when using a 50 μm-waist MDTF as distributed reflector., This work is part of the project PID2019-107270RB, funded by MCIN/ AEI/10.13039/501100011033 and FEDER 'A way to make Europe', the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 838143, the Beatriz Galindo BEAGAL18/00116 fellowship, the 'Fundación Caja Navarra' and 'Fundación la Caixa' with the proyect LCF/PR/PR13/51080004 and Projects for young researchers UPNA 2019.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Study of in-line capillary fiber sensor for uniaxial transverse deformation

  • Sánchez González, Arturo
  • Leandro González, Daniel
  • Dauliat, Romain
  • Jamier, Raphael
  • Roy, Philippe
  • Pérez Herrera, Rosa Ana
This research explores the impact of cyclic uniaxial transverse deformation on an in-line hollow-core fiber etalon. The structure consists of a 6 mm long section of capillary fiber spliced between two standard single-mode fibers. The optical response of the structure is theoretically analyzed in spectral and transformed domains, evidencing Fabry-Perot and antiresonant interferometric mechanisms. A validation of the theoretical behavior is carried out both through simulation and experimentation. The performance of the structure for uniaxial transverse deformation is subsequently evaluated by tracking the phase of the main component in the transformed domain. The relevance of measuring in the time domain is discussed, demonstrating improved accuracy over wavelength shift and inverse spatial domain methods. Several sensors with different internal diameters underwent cycles of transverse deformation, revealing robust linear trends in every case. On average, the structure demonstrated elastic behavior under deformations up to 42 μm, with a mean sensitivity of 0.174 rad/μm, and mechanical breakage taking place at 58 μm. The results confirmed the suitability of the sensor to withstand uniaxial micro-displacements or pressures, with smaller inner diameter capillary fibers showing the best performance., This work was supported in part by MCIN/AEI/10.13039/501100011033 and FEDER "A way to make Europe" under Project PID2019-107270RB-C22 and Project PID2022-137269OB-C21, in part by MCIN/AEI/10.13039/501100011033 and European Union "Next generation EU"/PRTR under Project PDC2021-121172-C21 and Project TED2021- 130378B-C22, and in part by the Public University of Navarre under Project PJUPNA06-2022. Open access funding provided by Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Long-range traffic monitoring based on pulse-compression distributed acoustic sensing and advanced vehicle tracking and classification algorithm

  • Corera Orzanco, Íñigo
  • Piñeiro Ben, Enrique
  • Navallas Irujo, Javier
  • Sagüés García, Mikel
  • Loayssa Lara, Alayn
We introduce a novel long-range traffic monitoring system for vehicle detection, tracking, and classification based on fiber-optic distributed acoustic sensing (DAS). High resolution and long range are provided by the use of an optimized setup incorporating pulse compression, which, to our knowledge, is the first time that is applied to a traffic-monitoring DAS system. The raw data acquired with this sensor feeds an automatic vehicle detection and tracking algorithm based on a novel transformed domain that can be regarded as an evolution of the Hough Transform operating with non-binary valued signals. The detection of vehicles is performed by calculating the local maxima in the transformed domain for a given time-distance processing block of the detected signal. Then, an automatic tracking algorithm, which relies on a moving window paradigm, identifies the trajectory of the vehicle. Hence, the output of the tracking stage is a set of trajectories, each of which can be regarded as a vehicle passing event from which a vehicle signature can be extracted. This signature is unique for each vehicle, allowing us to implement a machine-learning algorithm for vehicle classification purposes. The system has been experimentally tested by performing measurements using dark fiber in a telecommunication fiber cable running in a buried conduit along 40 km of a road open to traffic. Excellent results were obtained, with a general classification rate of 97.7% for detecting vehicle passing events and 99.6% and 85.7% for specific car and truck passing events, respectively., This work was supported in part by European Union “Next generationEU”/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER “A way to make Europe” and MCIN/AEI/10.13039/501100011033 under grant PID2019-107270RB, and in part by Gobierno de Navarra under grant PC210-211 FIBRATRAFIC.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

High performance fiber laser resonator for dual band (C and L) sensing

  • Sánchez González, Arturo
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
This work presents an experimental analysis and comparison of the performance of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror both in C- and L-band. Single-wavelength emission has been obtained in either band when using these artificially controlled backscattering fiber reflectors in a ring-cavity fiber laser. Single-longitudinal mode operation with an optical signal to noise ratio (OSNR) of 47 dB and an output power instability as low as 0.04 dB have been measured when employing a C-band optical amplifier. When replaced by an L-band optical amplifier, a single-longitudinal mode behavior has also been obtained, showing an OSNR of 44 dB and an output power instability of 0.09 dB. Regarding their performance as fiber-laser sensing systems, very similar temperature and strain sensitivities have been obtained in both bands, comparable to fiber Bragg grating sensors in the case of temperature and one order of magnitude higher in the case of strain variations., and European Union “Next generationEU”/PTR.This work is part of the project PID2019-107270RB, funded by MCIN/ AEI/10.13039/501100011033 and FEDER “A way to make Europe”, the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), and PDC2021-121172, funded by MCIN/ AEI/10.13039/501100011033
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Frazão, Orlando
  • Silva, Susana
A paracetamol concentration-sensing scheme based on a linear cavity fiber laser configuration is demonstrated experimentally. The laser cavity has a fiber sensor at one end, that allows refractive index measurements. The refractometer consists of a cleaved fiber tip combined with an FBG functioning as a reflecting mirror. The combination of a fiber loop mirror at the other end allows to reflect all the light from the FBG and refractometer, forming a linear cavity. By measuring the intensity variation of the Fresnel reflection at the fiber-to-liquid interface, the measured concentration is linear and have a concentration sensitivity of -8.74±0.34×10-5 µW/(g/kg), over a range of 52.61 to 219.25 g/kg, and with a resolution of 2.77 g/kg. The results obtained present high stability and prove the potential of the fiber laser system to performed real-time measurements of concentration, in a non-invasive way., This research was funded by: National Funds through the Portuguese funding agency, FCT - Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020 and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22 funded by MCIN/ AEI/https://doi.org/10.13039/501100011033 and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Time-transformed spectral analysis for multiparametric sensing using a single antiresonant interferometer

  • Jaso Gallego, Isabel
  • Sánchez González, Arturo
  • Bravo Acha, Mikel
  • Pérez Herrera, Rosa Ana
  • Leandro González, Daniel
This work explores the potential of spectral composition analysis in the time-transformed domain for multiparametric sensing using a single in-line hollow-core interferometer. By effectively distinguishing between antiresonance guidance and Fabry Perot-induced contributions, this approach allows simultaneous measurement of two independent parameters. The sensor, featuring polyimide coating, was characterized during humidity cycles at varying temperatures by monitoring phase variations in the transformed domain. The distinct sensitivities of antiresonance and Fabry-Perot components allowed the determination of temperature and relative humidity using a multiparametric linear model, achieving good agreement with experimental results and underscoring its robustness for multiparametric sensing applications., This work was supported in part by projects PID2019-107270RB-C22, PID2022-137269OB-C21 funded by MCIN/AEI/10.13039/501100011033 and FEDER 'A way to make Europe', projects PDC2021-121172-C21, TED2021-130378B-C22 funded by MCIN/AEI/10.13039/501100011033 and European Union 'Next generation EU'/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Stable L-band fiber laser sensor using a backscattering-based multimode fiber reflector

  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Sánchez González, Arturo
  • Durán Lázaro, María
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
A new and highly stable L-band fiber laser for sensing is demonstrated. An emission line at 1575.47 nm, was achieved using a special reflector. Good strain sensitivity, optical signal to noise ratio and output power stability were measured., This work is part of the projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, PDC2021-121172-C01 funded by MCIN/ AEI/10.13039/501100011033, the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), and European Union “Next generationEU”/PTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Láseres de fibra óptica basados en reflectores clásicos, estrechados y microperforados, Optical fiber lasers based on classic, tapered and micro-drilled mirrors

  • Sánchez González, Arturo
  • Pérez Herrera, Rosa Ana
  • Roldán Varona, Pablo
  • Rodríguez Cobo, Luis
  • López Higuera, José Miguel
  • López-Amo Sáinz, Manuel
En este trabajo se presenta un estudio comparativo entre distintos láseres de fibra óptica altamente dopada con erbio, con cavidades lineales conformadas tanto por reflectores puntuales clásicos como reflectores distribuidos. El estudio analiza experimentalmente las principales prestaciones de cada configuración, destacando las mejoras en estabilidad de emisión y estrechamiento de línea alcanzadas con fibras estrechadas microperforadas., This work presents a comparative study between different linear cavity highly erbiumdoped fiber lasers, both by means of classic point reflectors and newly developed distributed reflectors. The study analyzes the main parameters of each configuration, highlighting the enhancement in emission stability and line narrowing achieved with micro-drilled tapered fibers., Este trabajo ha sido financiado por el Ministerio de Ciencia e Innovación y la Agencia Estatal de Investigación (PID2019-107270RB), fondos FEDER, el Ministerio de Educación, Cultura y Deporte de España (Beca FPU2018/02797), y los Proyectos de Jóvenes Investigadores de la UPNA 2019 (PJUPNA1928).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Phase noise effects on phase-sensitive OTDR sensors using optical pulse compression

  • Loayssa Lara, Alayn
  • Sagüés García, Mikel
  • Eyal, Avishay
We introduce a detailed theoretical, numerical, and experimental study of the effects of laser's phase noise on the performance of phase-sensitive optical time-domain reflectometry (-OTDR) sensors that use optical pulse compression (OPC). Pulse compression is a technique that can be used to improve the received signal amplitude by increasing the effective energy of the pulses that are launched into the fiber without degrading the spatial resolution of the measurements. Therefore, it is a valuable tool to extend the range of these sensors and mitigate fiber attenuation constraints. However, it has been observed that the limited coherence of the laser source has a degrading effect on the actual performance enhancement that this method can provide. Here, we derive a theoretical model that can be used to quantify this degradation for any type of OPC such as those based on either linear frequency modulation (LFM) pulses or perfect periodic autocorrelation (PPA) bipolar bit sequences. The model facilitates numerical estimation of the sensitivity of the -OTDR measurements. It also produces theoretical expressions for the mean and the variance of the phase-noise perturbed backscatter response. These results are validated via numerical simulations and experiments in -OTDR setups using LFM as well as PPA OPC. Furthermore, we demonstrate the use of the model to investigate the basic trade-offs involved in the design of OPC -OTDR systems., This work is part of the project PDC2021-121172-C21 funded by MCIN/AEI/10.13039/501100011033 and European Union ‘Next generationEU’/PRTR, and of project PID2019- 107270RB, funded by MCIN/AEI/10.13039/501100011033 and FEDER ‘A way to make Europe’. The work was supported in part by the Israeli Science Foundation (ISF), grant number 2675/20.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Femtosecond laser inscription of diffraction gratings in CYTOP fibers for optical fiber sensing

  • Lomer, Mauro
  • Roldán Varona, Pablo
  • Algorri, J. F.
  • Rodríguez Cobo, Luis
  • Pérez Herrera, Rosa Ana
  • López-Amo Sáinz, Manuel
  • López Higuera, José Miguel
The use of the new CYTOP fibers for the inscription of optical structures and the sensing of different parameters has started to gain importance in the last decade. This work presents the design and manufacture of a CYTOP fiber-based optical structure intended for later use as a refractive index sensor. The structure is based on a diffraction grating inscribed in an area of the fiber with a specific curvature, and previously polished., This work has been supported by the FEDER/Ministerio de Ciencia, Innovación y Universidades and Agencia Estatal de Investigación (RTC-2017-6321-1, PID2019-107270RB-C21 and PID2019-107270RB-C22), the Ministerio de Educación, Cultura y Deporte of Spain (PhD grant FPU2018/02797), and Projects for young researches UPNA 2019.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Two-wavelength phase-sensitive OTDR sensor using perfect periodic correlation codes for measurement range enhancement, noise reduction and fading compensation

  • Sagüés García, Mikel
  • Piñeiro Ben, Enrique
  • Cerri, Enis
  • Minardo, Aldo
  • Eyal, Avishay
  • Loayssa Lara, Alayn
We demonstrate a two-wavelength differential-phase-measuring OTDR sensor that uses perfect periodic correlation phase codes to enhance the measurement performance. The two-wavelength technique extends the measurement range of OTDR sensors by synthesizing a virtual longer-wavelength measurement from two simultaneous measurements of phase using different lasers. This increases the range free from phase unwrapping errors. However, we find that the application of this technique greatly increases the relative measurement noise. To compensate for this issue, we introduce the use of optical pulse compression using perfect periodic correlation phase codes to increase the measurement signal-to-noise ratio and also to facilitate the simultaneous compensation of Rayleigh and polarization fading. In addition, we apply a method to further reduce the relative noise that is added to the two-wavelength measurement by using the synthetic wavelength measurement to unwrap the differential phase measured with a single wavelength. All this is highlighted in a 1-km sensing link in which up to 20-cm spatial resolution and 12.6 pϵ/√Hz strain sensitivity are demonstrated as well as a 67-fold enhancement in measurement range compared with the use of the conventional single-wavelength method., Agencia Estatal de Investigación (PID2019-107270RB-C22)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Compensation of phase-noise in pulse-compression phase-sensitive OTDR sensors

  • Piñeiro Ben, Enrique
  • Sagüés García, Mikel
  • Eyal, Avishay
  • Loayssa Lara, Alayn
We introduce a technique to compensate the performance impairments due to the laser phase noise in long-range pulse-compression DAS sensors. Experiments demonstrate the use of the longest duration pulse compression waveform to date., This work was supported in part by European Union "Next generationEU"/PRTR and MCIN/AEI/10.13039/501100011033 under grant PDC2021-121172-C21, in part by FEDER "A way to make Europe"and MCIN/AEI/10.13039/501100011033 under grant PID2019-107270RB, in part by Gobierno de Navarra under grant PC210-211 FIBRATRAFIC, and in part by the Israeli Science Foundation (ISF) under grant number 2675/20.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Fiber optic mirror fabrication using general-purpose metallic pigments

  • Jaso Gallego, Isabel
  • Mejia-Olivo, Edison
  • Bravo Acha, Mikel
  • Leandro González, Daniel
  • López-Amo Sáinz, Manuel
In this work, the potential of using general-purpose paints to fabricate highly reflective, low-cost optical mirrors is evaluated. The study shows that high-reflectivity mirrors can be created in standard single-mode fiber in a reliable, simple and economic manner using the appropriate metallic paint. Preliminary results confirm that the grain size of the metallic particles is a crucial factor in the reflective behavior, together with the substrate in which the particles are suspended. Moreover, interferometric patterns have been observed in some cases, which could lead to the creation of simple and economic fiber optic sensors., This work is part of the projects PID2019-107270RB-C02, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”, TED2021-130378B-C22, funded by MCIN/AEI/10.13039/501100011033 and European Union “Next generation EU”/PTR, and PDC2021-121172-C01 funded by MCIN/ AEI/10.13039/501100011033 and European Union “Next generationEU”/PTR and the project PJUPNA06-2022 from the Public University of Navarre and the Beatriz Galindo BEAGAL18/00116 grant funded by MICINN.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Effect of linewidth on the relative intensity noise in random distributed feedback raman fiber lasers

  • Rota Rodrigo, Sergio
  • Leandro González, Daniel
  • Santarelli, Giorgio
  • López-Amo Sáinz, Manuel
  • Ania-Castañón, Juan Diego
We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz., This research was funded by the Spanish Government grants RTI2018-097957-B-C33, PID2021-128000OB-C21, and PID2019-107270RB-C22; Conseil Régional d’Aquitaine (2017-1R50302-00013493); LAPHIA (Lasers and Photonics in Aquitaine); the Horizon 2020 Framework Programme (H2020) (Marie Sklodowska-Curie—748839); and Comunidad de Madrid project SINFOTON2-CM (S2018-NMT/4326). Additional support was from AEI/FEDER funds.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Measurement of paracetamol concentration using an erbium-doped fiber ring cavity

  • Soares, Liliana
  • Pérez Herrera, Rosa Ana
  • Novais, Susana
  • Ferreira, António
  • Silva, Susana
  • Frazão, Orlando
Process Analytical Technology (PAT) has been increasingly used in the pharmaceutical industry to monitor essential parameters in real-time during pharmaceutical processes. The concentration of Active Pharmaceutical Ingredients (APIs), such as paracetamol, is one of these parameters, and controlling its variations allows for optimization of the production process. In this study, a refractometric sensor, implemented by an interrogation system based on an Erbium-Doped Fiber Ring Cavity (EDFRC), was presented and experimentally demonstrated. The Cavity Ring proposed included a 1 × 3 coupler. One port of the coupler was used to increase the optical power of the system through a Fiber Bragg Grating (FBG), and the other two ports were used as sensing head and reference. The sensor detected variations of paracetamol concentration with a sensitivity of [(−1.00 ± 0.05) × 10−3] nW/(g/kg) and a resolution of 5.53 g/kg. The results demonstrate the potential of this technology as a possible non-invasive PAT tool., and European Union “Next generation EU”/PTR. Liliana Soares acknowledges the support of FCT, Portugal, through the Grant 2020.05297.BD.This research was funded by: National Funds through the Portuguese funding agency, FCT—Fundação para a Ciência e a Tecnologia, within project UIDB/50014/2020; National Funds through FCT/MCTES (PIDDAC), within projects LA/P/0045/2020 (ALiCE), UIDB/00511/2020, and UIDP/00511/2020 (LEPABE); Program “José Castillejo para estancias de movilidad en el extranjero de jóvenes doctores”, funded by the Ministerio de Univesidades of Spain (reference CAS21/00351); project PID2019-107270RB-C22, funded by MCIN/AEI/10.13039/501100011033 and FEDER “A way to make Europe”; projects PDC2021-121172-C21 and TED2021-130378B-C22, funded by MCIN/AEI/10.13039/501100011033